Related
A friend of mine also tried plugging in his HTC G2 (with Cyanogenmod), which also did not work. And I've been looking for a solution all around the place, and it seems to be a problem with Android phones in general; however, I know it's possible to get it working somehow because not everyone has the issue.
Basically, no matter if I have the USB connected via charge only or mass storage, the car display flashes "UNSUPPORTED". I've tried it with and without USB debugging enabled. And with all those combinations, I've tried having a music application open/no music apps running.
I also tried a solution here, which also did not do anything different.
I've also seen a few responses saying to just use Bluetooth instead. My car does not have Bluetooth capabilities. Using an AUX cable is a possibility, though I'd rather have the USB working.
Thanks!
Seems like the system wants to recognize your phone, but USB mode takes a few seconds to enable and therefore the system just rejects it. Disk mode will DEFINITELY have to be activated at some point, but the question is when. Try these steps:
1. With the car on, turn on the radio but don't have it in USB mode yet. Use radio, aux, cd, whatever. This will likely power the USB port at least.
2. Plug in your phone, make sure to select disk/mass storage mode.
3. Wait like 10-15 seconds for it to settle in, THEN select USB mode.
If that doesn't work, try different combinations. Like start with the radio completely off or something. If you have more than one USB port, try a different one. Other than that... I'm stumped. I got it working in a rental Ford Fiesta, but I don't remember the exact method. But it was something like this.
Try the radio with a USB stick drive to see if the radio even works that way
Sent From My Pocket
Sorry thegregbradley, I tried it but it didn't work.
I tried doing a couple of different things similar to that too, and it didn't work either.
As far as using a regular USB drive with some music files on it, it works fine! My friend used her iPod and that worked fine too. I don't see why it has such a problem with Android though...
In doing some reading, I have discovered information that says you need to turn USB debugging OFF for this to work...
Info comes from this thread:
http://www.hondacivicforum.com/foru...nics-10/2012-usb-android-support-88695/page2/
If not that, then I wonder if it's a problem of file management on your SD card? Just as a test, try putting your songs directly in your root folder. Or at most, one folder deep. The Fiesta I rented had bluetooth functionality, so I ended up doing it that way, as it was faster and less problematic. But I definitely would rather just plug it in if it just worked that way.
Iv found that running a rooted rom with debugging off and in mounted mode works great in my car.... No other combo has worked for me
@pwncloud, did you ever get this to work with USB debugging off? Just curious
I have debugging off in my car too and no mods to my android, it's a G2 and I get the same error on my 2012 Civic LX.
To update, no I never got it to work. I've settled with an aux cable.
Hello I am looking for guidance to fix my firestick. I've exhausted all search options.
I lost my firestick remote some time ago and just got competed moving. I decided to re setup my firestick. However I am running into the following issue.
I now have a new router, so my firestick is still looking to connect to the old router settings. I downloaded the firetv app but i can't remember my old router net id and password settings to create a hotspot with my phone and update my network settings.
I purchased a new remote as I have read you can just pair it to your current firestick by holding the home button for 10 seconds. I've tried this several times. However my firestick seems to be stuck in sleep mode. I have tried to unplug the firestick to reboot it. However I cannot get past the black screen.
I have verified that I am on the correct hdmi screen and the unit is plugged in. I also tried two different hdmi ports on my tv and no luck.
Does anyone have a work around or am I stuck buying a new firestick?
Do you see anything as the FireTV boots? It's just black?
malacoid said:
Do you see anything as the FireTV boots? It's just black?
Click to expand...
Click to collapse
I do not get to see it even boot. When I plug the unit into the hdmi port the screen stays black. I am on the correct hdmi setting on the tv. I have 6 hdmi ports and have no luck on any of them.
I've read that people say the USB cord can get burned out so the unit is not getting power. I will swap my iPhone cord to see if that is the issue.
Hi everyone, having weird issues with op9pro and new Mazda CX5 infotainment. I could get it connected a couple of times but it starts to disconnect everytime I use it.
I tried opo6 with a custom rom based on Android 10 and it works perfectly.
In my previous Mazda 6 the op9pro use to work without any issue.... I read around there are issues with AA and android 11 in general, with different cars, I tried various workarounds but it seems impossible to have a stable connection here... Am I the only one around? Some suggestions would be appreciated
I'm also having problems with AA on my car. Here is my work-around:
Standard power charging going on and off. Can't use Android Auto [work-around]
Work-around : https://forum.xda-developers.com/t/standard-power-charging-going-on-and-off-cant-use-android-auto-work-around.4258043/post-84822769 I'm having a problem when I plug my phone into my car usb-a for charging and Android Auto (AA)...
forum.xda-developers.com
You can read the full thread, I've tried a lot of things.
clavelm80 said:
I'm also having problems with AA on my car. Here is my work-around:
Standard power charging going on and off. Can't use Android Auto [work-around]
Work-around : https://forum.xda-developers.com/t/standard-power-charging-going-on-and-off-cant-use-android-auto-work-around.4258043/post-84822769 I'm having a problem when I plug my phone into my car usb-a for charging and Android Auto (AA)...
forum.xda-developers.com
You can read the full thread, I've tried a lot of things.
Click to expand...
Click to collapse
thx, already ordered a new cable, I will give it a try and trace it here!
wollax said:
thx, already ordered a new cable, I will give it a try and trace it here!
Click to expand...
Click to collapse
Changing cables did not solve the AA problem for me. Except the oneplus 3t cable, I've only tried with anker ones. Maybe I should have tried other brands.
Interesting thing, the Anker USB-C to USB-A USB2 cable has solved the problem with my older power-bank.
hi to all, changed cable, tried PTP workaround, it could work once or twice but later as you connect the phone to the car it won't work for sure .... a real pain .... the only way for me is to use the old OP6 with android 10 custom ROM with the car, and the OP9P (main device and number!) not connected at all with the car, using a BT headset to answer while driving ..... what a shame!
wollax said:
hi to all, changed cable, tried PTP workaround, it could work once or twice but later as you connect the phone to the car it won't work for sure .... a real pain .... the only way for me is to use the old OP6 with android 10 custom ROM with the car, and the OP9P (main device and number!) not connected at all with the car, using a BT headset to answer while driving ..... what a shame!
Click to expand...
Click to collapse
Have you tried setting don't optimize for aa, then when you plus your phone into your car hold on the notification. Change it to important then turn sound and vibration off for that notification
I had similar issues with my OP9. I then made sure USB debugging was on in developer settings and that fixed the issue.
toolhas4degrees said:
Have you tried setting don't optimize for aa, then when you plus your phone into your car hold on the notification. Change it to important then turn sound and vibration off for that notification
Click to expand...
Click to collapse
thanks for suggestion but no way, I can connect once the OP9P playing with usb in developer section settings, but it works once, and I have to delete the car from the phone and the phone from the car settings ! When I reconnect to the car the OP9P starts to opening AA and closes it quickly, it never connects as my old OP6 with android 10 and custom ROM does ....
Now I am waiting for amazon to deliver other usb cables from Ugreen, but I don't think they will solve my issue .... hope very soon a custom ROM will arrive for this OP9P so that I will probably solve this SW issue, not sure it is only on Goolge side the reason for this issue, I suppose it could be something on Oneplus Oxygen ....
XNine said:
I had similar issues with my OP9. I then made sure USB debugging was on in developer settings and that fixed the issue.
Click to expand...
Click to collapse
sure I have developer activated but it's not enough!
wollax said:
sure I have developer activated but it's not enough!
Click to expand...
Click to collapse
You need developer settings on.
You need to turn on USB Debugging.
If this still fails, try switching the DEFAULT USB CONFIGURATION to FILE TRANSFER from NO DATA TRANSFER.
You may need to reboot after this, you may not.
Default USB Configuration is found under the Networking section in Developer Options, between Tethering hardware acceleration and Show Bluetooth devices without names.
XNine said:
You need developer settings on.
You need to turn on USB Debugging.
If this still fails, try switching the DEFAULT USB CONFIGURATION to FILE TRANSFER from NO DATA TRANSFER.
You may need to reboot after this, you may not.
Default USB Configuration is found under the Networking section in Developer Options, between Tethering hardware acceleration and Show Bluetooth devices without names.
Click to expand...
Click to collapse
all settings are ok in the OP9P, but it works as usual only once and after I stop the car in never reconnects again! if I reboot OP9P sometimes it works again .... for me it's not the "right" way to use it.
the OP6 works perfectly you can connect and disconnect how many times you want it never fails!
let's wait for next oxygen updates and maybe also google patches for their SW .... thanks again for sharing your experience!
Here is an update, after some time trying various combinations, I realized this device works perfectly the first time you connect to the car, if you turn off the car for example to get some fuel for a few minutes or less, or if you disconnect the phone and reconnect it without waiting, op9p won't connect anymore, but if you wait like a quarter then it will work perfectly.... the old op6 is not doing like that!!!!
Anyway now I know how to make it work and I can handle it someway!
Does anyone know why I'm having android auto issues? When I connect my phone, it just loops connecting and disconnecting android auto over and over, and randomly will decide to connect after some amount of time or rebooting the phone. Just to clarify, once it connects it stays connected, so it's just an issue with the initialization.
It is not the cable, I've used it with my Galaxy for a while and even tried others. This issue was also present before and after rooting so I know it's not that. This was also present on the OP9 non-pro I tried. I also tried switching the default USB mode to File Transfer and PTP with no improvement.
Thanks guys!
Hi, there is a problem with the 1+9 pro, not yet fixed in Oxygen OS 11.2.5.5.LE15BA.
Here is a thread about it, and a work-around that works for me,
but not for everyone it seems.
Standard power charging going on and off. Can't use Android Auto [work-around]
Work-around : https://forum.xda-developers.com/t/standard-power-charging-going-on-and-off-cant-use-android-auto-work-around.4258043/post-84822769 I'm having a problem when I plug my phone into my car usb-a for charging and Android Auto (AA)...
forum.xda-developers.com
clavelm80 said:
Hi, there is a problem with the 1+9 pro, not yet fixed in Oxygen OS 11.2.5.5.LE15BA.
Here is a thread about it, and a work-around that works for me,
but not for everyone it seems.
Standard power charging going on and off. Can't use Android Auto [work-around]
Work-around : https://forum.xda-developers.com/t/standard-power-charging-going-on-and-off-cant-use-android-auto-work-around.4258043/post-84822769 I'm having a problem when I plug my phone into my car usb-a for charging and Android Auto (AA)...
forum.xda-developers.com
Click to expand...
Click to collapse
Glad to know it's OP and not my phone. I'm confident the cable isn't the issue. In terms of your workaround, why not just set PTP as default in developer settings? What's different about setting it yourself?
dkcats3 said:
Glad to know it's OP and not my phone. I'm confident the cable isn't the issue. In terms of your workaround, why not just set PTP as default in developer settings? What's different about setting it yourself?
Click to expand...
Click to collapse
First, choosing PTP or "data transfer" does the trick. When the connection to AA is stable, the phone goes back to "only charging" .
Secondly, I did not try "extensively" setting a default connection mode other than charging in dev options when looking for a work-around.
Some said it works for them (one 1+ forum) but when I tried it, it didn't for me. I did not try to set it, reboot, try, set another, reboot. I was looking for something better so I've skipped it and my actual work-around is okay for me.
Thirdly, I don't like to let a connection access to the data of my phone without having to unlock it.
After I did the update yesterday when I connect any of my USB DACs they stop playing after I turn the screen off. When I turn the screen back on it doesn't resume playing and other apps freeze up and it will even restart on its own until I disconnect my USB DAC. I tried messing with the USB settings and nothing seems to affect it. I'd rather not hard reset, I will lose a few things like Vanced that I had prior to it being discontinued. I know there's a new one out there but if there is another solution I'd like to try that first. Any suggestions?
Found the fix!! Too bad I didn't find it before I factory reset my phone... Smh..
I found the problem, default USB settings were set to File Transfer.
Settings > Developer Options > Default USB Configuration > No data transfer.
Audio will now play with screen locked and adapter plugged in.
Click to expand...
Click to collapse
Original Article Thread