Guide for Install TWRP & Root Moto_C_Plus With Locked Bootloader
I have ported TWRP recovery for Moto C Plus
TWRP porting guide followed on xda [thanks for xda]
Code:
Follow instruction correctly..try at your own risk..i'm not responsible for if your device bricked..
Here is the step by step procedure for install twrp recovery on moto c plus with locked bootloader
Instructions:-The simple way to install twrp recovery on devices,, is to unlock the bootloader..and flash the recovery through fastboot..
I'm going to show you step by step instructions to flash the twrp on moto c plus WITHOUT unlocking the bootloader or lose any data.
1. first thing u need to some files..
Download and extract my ported recovery & files from here Tools NEW G-DRIVE LINK UPDATED!!!
Code:
[I][FONT="Times New Roman"][COLOR="Red"][SIZE="4"]note:[/SIZE][/COLOR][/FONT][/I]after dowloading file..
extract it and copy [I]SuperSU-v2.82-201705271822.zip[/I] file in ur sd card,,,,
DONT FORGET to flash SuperSU-v2.82-201705271822.zip file
after write memory ,,otherwise your device will stuck at
moto logo or soft brick
2.Open download tool(file provided in the above link,use provide sp_flash tool only because moto c plus have secure chip,need to authentication file,, so u cant flash through normal sp_flash tool) and load the download agent "MTK_AllInOne_DA.bin" & authentication file auth_sv5.auth from download_tool folder
3.Load the scatter-file found in the provided file.. select preloader only..but don't flash it.
4. Click Alt + Ctrl + V to activate advanced mode in sp flash tool.
5.Click on "window" up there and select "write mode"
6. Change the Begin address to "0x2d80000" and click on "file path" and choose the TWRP RECOVERY.img from extracted provided zip file
7. Click on "write Memeory", then Power off your device and remove the battery.. press and hold vol- button, then connect phone to pc via USB cable.. press &hold vol- key until pc detect...wait for Write memory ok window appears,, now your recovery is ready.
8.Next insert ur battery, press vol+ and power button simultaneously.. than select recovery mode..& boot into recovery
9.In twrp recovery select install and locate SuperSU-v2.82-201705271822.zip file in ur sd card and flash it..
10.After successful flash... hit reboot device..
!!!NOW YOU ARE ROOTED MOTO C PLUS!!!! Enjoy!!!!:good::good:
...Image Instruction are also available in attached file..
For Compiled twrp go here Compiled Twrp
XDA-DevDB Information
TWRP For Moto C Plus with locked bootloader. Tool/Utility for all devices MT67xx
Contributor:
shr!pad
Created:13-12-2017
Last Update:02-05-2018
If u like my work, hit like button....
In ticked preloader , wut can I choose Broo.. ( TWRP RECOVERY.img ) ,??????
---------- Post added at 11:37 AM ---------- Previous post was at 11:32 AM ----------
Any Mtk Drivers Needed for pc to detact phone ????
u dont need to add twrp recovery in download section..u need to select twrp recovery in write memory...see in attached images..
Yes..u need mtk vcom drivers for detect phone..
I get this error
S_FT_ENABLE_DRAM_FAIL (0xFC0)
[EMI] Enable DRAM Failed!
[HINT] Please check your load matches to your target which is to be downloaded.
check..image instruction.. All files must be loaded..
And check u r enterd beginning adress 0x2d80000 is correct..
See instruction correctly..i think u r problem..in connecting phone...
Read instruction again..said that..press and hold vol- key then connect usb to phone..hold vol- key untill write memory ok window appears..?
Welcome
u dont need to add twrp recovery in download section..u need to select twrp recovery in write memory...see in attached images..
Yes..u need mtk vcom drivers for detect phone..
I double checked evey file and the begin adress, and i remove the battery hold vol - and connect the phone until in the status shows write memory but getting the same error in my 1+16gb
In the note section, u have mention flash SuperSU-v2.82-201705271822.zip file after write memory, this has to be done in the 9th step??
Yes..that to be done in 9th step
Yes..that to be done in 9th step
check that, r u installed vcom drivers correctly....is required for detect u r device..
Bro , TWRP successfully flashed but after flashing TWRP my moto c plus was not booting up strucking on MOTO LOGO ( I again flashed full firmware for use my phone )
Thanks for your work. I'm getting the Dram error as well.
Have double checked all the steps, using supplied cable and tried different ports on the PC.
My device is XT1723. Could it be that this version of TWRP is not correct for my device?
Kindly give proper credit
work on Xt1726 too?
After several unsuccessful attempts on XT1726, this method does not work... But, thank you for your hard work!
u need to flash super su file.. after writing the recovery provided in link.. otherwise u will bricked..read 9th step,,,,it's the problem u have facing
it's correct twrp.. i think ur problem..in drivers,, first install vcom drivers for detect the phone..
yes..thank you.. u need to first install usb vcom drivers for detect phone...
Related
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
BUGS / Not functioning features :
Backing up the data not working
USB mount SDCARD through recovery not working
Credits:
I, Me & Myself..
EDIT:
i have tried removing some bugs, try and tell me u all!!!
I have also included the stock recovery.img file in the attatchment for people who want the stock recovery.
********************Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!*********************
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Good Job done
Built from source or using web builder?
i cant flash this through sp - tool
vshlkmr said:
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Credits:
I, Me & Myself..
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Click to expand...
Click to collapse
while downloading i got the error
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
First Check if the MTK drivers are installed, check it by going tinto the device managers hardware section in my computer
If it is proper then try connecting your phone without the battery inserted
Same problem..
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
I'm facing the same problem.. I tried with battery in and out.. have installed the drivers as well..
i ported this recovery from a ZOPO Z900 Leader chinese android handset...i tried building from source, but i failed at it because of partition style in a18...
For people facing problems flashing it through sp tools, u all can try to flash it using another pc or alternatively view this youtube video -> http://www.youtube.com/watch?v=969xwsUTkSY
ujjwalk308 said:
I'm facing the same problem.. I tried with battery in and out.. have installed the drivers as well..
Click to expand...
Click to collapse
Same problem here.
Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!
vshlkmr said:
Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!
Click to expand...
Click to collapse
Ok.now waiting for the bugfix.
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
always usb cable error
Connect usb cable & discconet auto & charging mode
this is usb driver ????
great job. im a noob at this so will try after people posting have successfully ported the cwm to their phone
There are two recovery.img files in your attachments. recovery.img and cwmfinal.img. Which one should be used in sp flash tool?
I recently purchased Karbonn a21, can I try this on it?
Sent from my GT-I9300 using xda app-developers app
Thnx bro worked like a charm.
Sent from my Karbonn_A18 using xda app-developers app
fail root
plz send device manager screen shot
Can anyone please upload stock rom of karbonn a18. My device stock at boot animation screen.
Sent from my GT-P1000 using xda premium
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
same problem any help pz
Cwm flashed
I have successfully installed cwm on my karbonn a18.
I did it wit the help of mobileunckle tools.
What are the next motives now??
1) can we change the battery indicator at the notification area to percentage signs?
vshlkmr said:
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
BUGS / Not functioning features :
Backing up the data not working
USB mount SDCARD through recovery not working
Credits:
I, Me & Myself..
EDIT:
i have tried removing some bugs, try and tell me u all!!!
I have also included the stock recovery.img file in the attatchment for people who want the stock recovery.
********************Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!*********************
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Click to expand...
Click to collapse
will you please give CWM for Micromax A90 specification maybe same as A18
here is Specification
Micromax A90
Super Amoled Plus LCD with 262 k
MTK6575 CPU 1 Ghz
512 MB RAM (350 - 400) User available
512 MB ROM ( its not RAM ) for apps
2.5 GB external SD for media file ( Music/Video,,,etc.)
8 Mega Pixel Camera + 0. Mega Pixel Front Camera
Android OS 4.0.3
with Rooted cell
plz help us to create new CWM + Custom ROM
also its same specification from some Chinese Brand like Zoppo / Hero / Gionnee / HDC
plz help.
Pritesh.mohan said:
I have successfully installed cwm on my karbonn a18.
I did it wit the help of mobileunckle tools.
What are the next motives now??
1) can we change the battery indicator at the notification area to percentage signs?
Click to expand...
Click to collapse
You could do that before flashing Cwm aswell.. Use rom toolbox.. I did it the day I got this phone
:highfive:Hi guys, because of the lack of support for our phone, I wanted to create a unified thread for all Optimus EX SU880.
this thread aims to help all users to flash, upgrade or unbricked their phone.
disclaimer:
I am not a developer but just a mere user of SU880 so i am just collating all information i can gather to help us understand our device more further.
so before doing something posted on this thread, please make sure that you do your own back up because I will not be held responsible if you bricked or damage your phone.
Downloads:
V20c Firmware
V19c Firmware
APX Driver
Bootloader installer for V19c
CWM for V19c
Xrecovery For V19c
Root For V19c
ROOT for V20c
LG USB driver
KDZ_FW_UPD_EN.7z
Smart Flash
Rom Converter
Words you might encounter
1.KDZ = File extension for firmware
2.APX mode aka NVflash = utility where you can flash bios for devices that has nvidia card
3.SOFTWARE UPGRADE mode aka S/W = mode where you can flash a firmware normally
For V19c
Things to do:
1.enable USB debugging
2.back up your files (in case of fire =p )
Upgrading to Stock ROM
Step 1.
>Plug your device via USB cable
>Enable USB debugging and Install the LG united Driver
Step 2.
>Run Rom converter and Extract the Content of your KDZ file
>The tool will asked you about integrated tool ClockworkMod select No and press Enter
>It will extract 3 files but whats important are the SU880_ap.Bin and SU880_cp.fls (take note of the location of the file) then close the RomConverter
>Open SmartFlash and click on the tab ROM copy D/L
>Select the 2 files that you extracted earlier (CP bin for the CP file / AP bin for the AP file)
>tick on normal mode
Step 3.
>Enter S/W mode on your phone
>Power OFF the phone
>Hold the Volume down(-) then Plug the USB cable
>Wait until the SmartFlash Detect the COM port and the Communication driver
>Click the Start button on the SmartFlash tool
>Wait until it says Complete then Reboot your phone by Remove/Insert the battery then press the power button
Rooting V19c stock ROM
>Unplug USB cable
>enable USB debugging mode then Plug back the USB
>Download Root for V19c above
>extract the content to a folder and run ROOT.bat
>press 1 under CMD and select Data Restore on your phone screen
>your Phone will restart
>Turn ON your Phone and you will receive a message from the command prompt that the root is successful
>to verify, you can look for a new ICON (android with a red cape flying)
For V20cc
Things to do:
1.enable USB debugging
2.back up your files (in case of fire =p )
Upgrading to Stock ROM
Step 1.
>Plug your device via USB cable
>Enable USB debugging and Install the LG united Driver
Step 2.
>Enter S/W mode on your phone
>Power OFF the phone
>Hold the Volume down(-) then Plug the USB cable (wait until the computer install the drivers)
>Download the v20c KDZ file
>Run KDZ_FW_UPD and select the V20c KDZ file that you have downloaded
>Select Type: 3GQCT Phonemode: DIAG
>Click Launch Software Update
>Let the application Run until it says finish
>Wait until it says Complete then Reboot your phone by Remove/Insert the battery then press the power button
Note:
**Some user encounter error when using The KDZ Updater (crash / freeze / hang)
**try running the KDZ Updater via Administrator / Go back to Win 7 default theme (not aero) /use Windows XP as an alternative.
Rooting V20c stock ROM
Step 1.
>Unplug USB cable
>enable USB debugging mode then Plug back the USB
>Download Root for V20c above and extract
Step 2.
>Enter APX mode
>Download and install the APX driver above
>remove battery, mmc card and Sim
>phone PIN code
>Hold Both Volume rocker (-) (+) while plugging the USB cable
>Run Start_rooting.bat File and press enter under Command prompt.
>after the CMD finished loading the bootloader
>unplug USB cable and insert the battery back
>Turn on the device normally
>plug the USB cable back
>press enter agan on the command prompt windows t finish the rooting
>wait until it shows root finished
THanks,
That's it for now, but if you have any other question, Just feel free to ask.
and by the way, some of the tools are program using different language so please just bear with them.
One thing that i can promise you is my Phone is unbrickable. =)
Extra:
1.Disable SMS limit
>download Root explorer from the market or you can look for other free app that can enter you root directory
>Download Handcent/ GO sms
>open root explorer then Navigate to >Etc folder>Featuredset.xml>look for Max_user_data, Limit_user_data , Max_user_data and change it your countries preferred value.
Hit "thanks" for the effort =)
Provision Official V4
Jelly bean 4.1.2
Provision Official V4
How to:
1.Install CWM recovery
2.Boot into CWM and perform Factory Reset/Wipe Cache (use volume rocker and power button to navigate)
3.install Provision_official_4SU880.zip
4.reboot device
5.reboot to CWM recovery
6.install gapps for jb (formula 84)
7.reboot normally (you will get Android upgrading message)
8.Enjoy
**fix limited SMS
**Device will be rooted automatically
**device wont reboot changing signal from GSM to WCDMA
**additional settings found
**better battery life
**bloat apps remove
******PLEASE POST YOUR FEEDBACK*******
known issue:
**vibration due to kernel issue
**HDMI connection
LGSU880_4.2.2 version-CM10.1 system - final version
change log here (make sure to use google chrome to translate)
http://bbs.angeeks.com/thread-3009972-1-1.html
Steps:
1.Download CWM recovery
CWM Recovery extract content to desktop
2.Download rom and put it inside your SD card
LZ_LGSU880
Google service pack
3.Remove battery
4.press the volume rocker (-)(+) while plugging the USB
5.if ask for APX driver, manually install it. (APX driver included in the folder)
6.Open the CWM folder and run FLASH.bat
7.boot to CWM and flash the ROM and Update
8.Perform a factory reset.
Enjoy
alamatnitotoy said:
[Reserved]
Custom Rom page
Click to expand...
Click to collapse
Can i use CWM and EXrecovery (v19c) for v20c rom?
Hi @alamatnitotoy !
Me and my friend, who has su880, were testing the v20c kdz.
We flashed v20c kdz using KDZ updater, smartflash and even we tried the offical LG update upgrading from v19c to v20c.
After every way of flasing v20c the phone always stucked at LG boot logo. So We read back every partition from the phone and it turned out that the LNX partition, which contains the kernel, is empty. I mean the kernel was missing after every flash of v20c, but every other partition was okay.
We extracted the the every file from the kdz and the the kernel image was empty in this case as well.
I don't know what is it. Maybe we are doing something wrong or LG simply left out the kernel file from v20c?
Did you flashed v20c?
boy977 said:
Can i use CWM and EXrecovery (v19c) for v20c rom?
Click to expand...
Click to collapse
as far as i know, you should use the one that is design for each version
bitdomo said:
Hi @alamatnitotoy !
Me and my friend, who has su880, were testing the v20c kdz.
We flashed v20c kdz using KDZ updater, smartflash and even we tried the offical LG update upgrading from v19c to v20c.
After every way of flasing v20c the phone always stucked at LG boot logo. So We read back every partition from the phone and it turned out that the LNX partition, which contains the kernel, is empty. I mean the kernel was missing after every flash of v20c, but every other partition was okay.
We extracted the the every file from the kdz and the the kernel image was empty in this case as well.
I don't know what is it. Maybe we are doing something wrong or LG simply left out the kernel file from v20c?
Did you flashed v20c?
Click to expand...
Click to collapse
yes i did flash the v20c. I had that problem before also when using other flasher other than the kdz updater. also sometimes when its failing, what i do is i run the file "Root v20c" thru apx before using the KDZ updater to upload the v20c
alamatnitotoy said:
yes i did flash the v20c. I had that problem before also when using other flasher other than the kdz updater. also sometimes when its failing, what i do is i run the file "Root v20c" thru apx before using the KDZ updater to upload the v20c
Click to expand...
Click to collapse
Thnak you! The rooting-forv20c.rar contains the v20c kernel file.
I need CWM for v20c.Do you have it?
@alamatnitotoy I looked deeply into why flashing v20c brick your phone. My statement that the kernel image is missing from v20c was wrong. The kernel is there but an wrong place. When you use the extractor from P990 AIO toolkit to extract the image files from AP.bin file, the extractor shows you that which image file is at what OFFSET (or address) in the AP.bin file. Here is what am I talking about:
Code:
[01] address=0x00100000 size=0x00400000 // bct file
[02] address=0x00500000 size=0x00200000 // partition layout
[03] address=0x00700000 size=0x00200000 // bootloader
[04] address=0x00900000 size=0x00600000 // recovery
[05] address=0x00f00000 size=0x2bc00000 // system
[06] address=0x2cb00000 size=0x00600000 // kernel
[07] address=0x2d100000 size=0x12c00000 // internal sd content
These adresses also used during smartflashing. These adresses tells the smartflash where is the kernel image and system image and etc in the v20c AP.bin file
If you flash v20c and you read back the 12th partiton with nvflash you can see only zeros.
If you open teh v20c AP.bin file in a hex editor and you go to the 2CB00000 offset you can see there is nothing just bunch of zeros, the kernel is not there. The kernel actually at 2E000000 offset. Not just the kernel is at a wrong offset, also the sd-img is at the wrong offset. sd-img should be at 2D100000 offset, but in the v20c AP.bin it is at 2E600000 offset. So, when you flash v20c the kernel partition will be filled with 00 hex values and the internal sdcard got damaged as well, because the kernel image gets flashed to the internal sdcard. This cause the Stuck at LG boot logo effect, even if you flash v20c kernel to the righ partition with nvflash, because the internal sdcard is damaged.
Fixing v20c AP.bin file:
There are only 00 hex values From 2CB00000 to 2E000000.
Delete those 00 hex values, then the kernel image and the sd-int.img get to the right offset
Insert the same amount of 00 hex values as the amount of deleted 00 hex values to the end of the v20c AP.bin file to keep the size of the sd-int.img, then save the modifications.
I flashed this modified v20c AP.bin to my p990. I read back every necessary partition with nvflash and everything was okay. bootloader, bct, partitions, kernel, recovery, system are aon the right partition so maybe it's fixed, but I am not 100% sure just 98% because I don't have su880
I want to share you and with others the fixed v20c, so you can test. You can download it here
I want to share my google drive folder as well where you can find my works with su880. It has cwm for v19c and v20c. I also write a read me how can you flash it and root your phone with CWM. Well it was not tested as well, I am 98% sure it works, because rooting p990 and su660 stock roms works that way and p990, su660 and su880 almost the same. I use the CWM recovery image from "CWM for v19c".
My folder is here, some files are still uploading. I will notice you in this post when it is finished
There is no bootloader.img in the folder "SU880_V20C_CWM".Have you forgot it?
boy977 said:
There is no bootloader.img in the folder "SU880_V20C_CWM".Have you forgot it?
Click to expand...
Click to collapse
Oh sorry . Bootloader is there just rename it to bootloader.img from bootloader.bin, or download the rar file again from my google drive folder. I fixed it now.
I'm trying to fix "dual clock" at the lockscreen on my v20c rom.Do you know how?
boy977 said:
I'm trying to fix "dual clock" at the lockscreen on my v20c rom.Do you know how?
Click to expand...
Click to collapse
Search for that in the Optimus 2x forums, there should be the solution. I remember that some peopla who are useing su660 solved this dual clock thing.
smartflash
i have flashed my su880 with smartflash as u teach above, now it stuck lg logo? what should i do? please help..
joeclap said:
i have flashed my su880 with smartflash as u teach above, now it stuck lg logo? what should i do? please help..
Click to expand...
Click to collapse
What rom did you flashed? Ippnclude download link for the downloaded rom.
Sent from my LG-P990 using xda app-developers app
Celebrate mempaho
bitdomo said:
What rom did you flashed? Ippnclude download link for the downloaded rom.
Sent from my LG-P990 using xda app-developers app
Click to expand...
Click to collapse
V20c rom, i've extracted rom files by rom covertor and flashed with smartflash. Thats all. Now stuck lg logo...
joeclap said:
V20c rom, i've extracted rom files by rom covertor and flashed with smartflash. Thats all. Now stuck lg logo...
Click to expand...
Click to collapse
If you can go to S/W download mode then flash this with smartflash. If you can't go to S/W download mode use "Bootloader installer for v19c", and flash that rom I linked
I cant go s/w mode but volume+ power working. What should i do? Can u explain step by step? Where i can find bootloader installer for v19c?
joeclap said:
I cant go s/w mode but volume+ power working. What should i do? Can u explain step by step? Where i can find bootloader installer for v19c?
Click to expand...
Click to collapse
The bootloader installer is at the first post of this thread.
Enter your phone to APX mode:
Remove battery
Press and hold volume_up and voulume_down button while you connect USB cable
Install APX drivers
Run the bootloader installer for v19c.
Hey i need bootloader for v20c.Can you give it to me?
Update: SPFlashTool flashable Marshmallow firmware file is now available. Build MOB30N.
OTA links are already there on xda, but here was no specific thread for Canvas A1 so i am writing one
Google has released the OTA files for Canvas A1 and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery. (Not applicable if using sp flash tool)
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
Canvas A1 users can easily update their device by following method(s)
Method 1 (the usual method):
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_aq4501sprout_aq4501/dc78fbefaf5f69cc4754751251d9ece094bc96e6.signed-sprout-mmx-MRA58M-from-LMY48M.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0 :laugh:
Method 2 (using sp flash tool, best method)
This method can be used even if you are running a custom rom. You can also use this method to unbrick Micromax Canvas A1.
Pre-requisites: Windows computer, USB cable, and most important "patience".
Step 1:
a) Download micromax driver.{thanks to @mohsin.r.munshi}
Extract its content, you will find an .exe file inside a folder "driver9401". Disable your antivirus and run the .exe file as administrator. (If you are using 64-bit windows, you will need to "disable driver signature enforcement". Google it)
b) Download SP Flash tool from my mediafire or from its official website. Extract it to any folder
c) Download SPflashTool flashable Marshmallow firmware . Extract the zip file. You will see the following files in it (similar not exact)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Note the location of MT6582_Android_scatter.txt file
Step2: Goto the folder where you have extracted sp flash tool. Run flash_tool.exe
Step 3: In sp flash tool, Click on "scatter loading". Then locate and select "MT6582_Android_scatter.txt". SP Flash tool will load all firmware files from the folder where you have extracted the OTA files.
Step 4: Power off your phone. And REMOVE the battery. Now on SP flash tool, click on "Download".
(refer to screenshots given on this website. Ignore the steps given on this website, just refer screenshots)
Step 5: (pay attention to every word) Connect USB cable to your phone only. Then Press and HOLD volume down button and insert the other end of USB cable to your pc. Flashing will start automatically. Wait till you see "OK" message on your pc.
Step 6: Once you see "OK" message, disconnect your phone and reinsert your phone's battery. Turn ON your phone. The first boot will take longer than usual.
Congo! You just updated/unbricked your Micromax Canvas A1.
Feel free to post comments for any doubts and errors
My canvas a1 software has been damaged, and it shows an error while installing update from sd card , so how do I can solve this problem ???? Please reply fast........
gd5121995 said:
My canvas a1 software has been damaged, and it shows an error while installing update from sd card , so how do I can solve this problem ???? Please reply fast........
Click to expand...
Click to collapse
flash official lollipop rom using method 2 above
Hi.. I'm on CM13 now. But I don't have mobile data for some reason. So I want to flash stock ROM. But last time I tried flashing stock, it wiped my IMEI numbers. Luckily my warranty status was somehow reset. So I had to get the phone replaced. Does this have a chance to cause the same problem (wipe my IMEI numbers)??
GughanRk said:
Hi.. I'm on CM13 now. But I don't have mobile data for some reason. So I want to flash stock ROM. But last time I tried flashing stock, it wiped my IMEI numbers. Luckily my warranty status was somehow reset. So I had to get the phone replaced. Does this have a chance to cause the same problem (wipe my IMEI numbers)??
Click to expand...
Click to collapse
sp flastool wipes userdata only, you wont loose your imei using spft.
sziraqui said:
sp flastool wipes userdata only, you wont loose your imei using spft.
Click to expand...
Click to collapse
Realy sorry to say this, but I lost my IMEI using SP Flashtools only. Check this thread.. There are a lot of other users facing the same problem.
And SN Write Tool method didn't help me get my IMEI back.. So I want to be really sure before flashing this time
recover imei android one....
try this...worked for my spice android one (mi-498)
http://forum.xda-developers.com/cro...lashable-zip-imei-repair-android-one-t2992846
GughanRk said:
Realy sorry to say this, but I lost my IMEI using SP Flashtools only. Check this thread.. There are a lot of other users facing the same problem.
And SN Write Tool method didn't help me get my IMEI back.. So I want to be really sure before flashing this time
Click to expand...
Click to collapse
In that case, i would suggest you to take a backup of your imei data using MTK Droid tool. Also copy your nvram folder straight from your phone to as many external storages as you can. Nvram (imei data) somehow becomes unrecognised after downgrading some phones.
Solution:
1. Use MTK droid tool to restore it from a previous backup.
or
2. locate nvram folder ( /data/nvram, correct me if i m wrong) DELETE it. Then paste a copy of your nvram folder that you copied when imei was not lost. DONT chmod. You will most probably get your network working (ensure that sim card was PRSENT and Radios were ON during this copy paste) within few seconds. I did this to restore imei on galaxy s4.
well, i have flashed 9 different mediatek phones using spflashtool, didnt lose imei in any.
sziraqui said:
In that case, i would suggest you to take a backup of your imei data using MTK Droid tool. Also copy your nvram folder straight from your phone to as many external storages as you can. Nvram (imei data) somehow becomes unrecognised after downgrading some phones.
Solution:
1. Use MTK droid tool to restore it from a previous backup.
or
2. locate nvram folder ( /data/nvram, correct me if i m wrong) DELETE it. Then paste a copy of your nvram folder that you copied when imei was not lost. DONT chmod. You will most probably get your network working (ensure that sim card was PRSENT and Radios were during this copy paste) within few seconds. I did this to restore imei on galaxy s4.
well, i have flashed 9 different mediatek phones using spflashtool, didnt lose imei in any.
Click to expand...
Click to collapse
Thanks! I'll post an update when I come around to flashing the stock ROM. Don't have the time now.
hi can i use these update for micromax unite2(8gb) from lolipop to marshmallow.
Firmwares are device specific. You CANNOT install a this on any other phone. You will brick your phone by installing a ROM which is not made for your device
Please update stock marshmallow link sir as soon as possible
.......
Thanks in advance
Micromax android one got hang at marshmallow logo.
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
ravipreet23 said:
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
Click to expand...
Click to collapse
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
ravipreet23 said:
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
Click to expand...
Click to collapse
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
sziraqui said:
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
Click to expand...
Click to collapse
I have installed all drivers as my pc detect my mobile as i can see in device manager. I perform all steps that you mention but SP flash player show nothings. CAn you tell me can i flash Lollipop stock rom on my android one which is running marshmallow previously. I cant find marshmallow stock rom thats why i have to flash lollipop stock rom??
sziraqui said:
OTA links are already there on xda, but here was no specific thread for Canvas A1 so i am writing one
Google has released the OTA files for Canvas A1 and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery. (Not applicable if using sp flash tool)
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
Canvas A1 users can easily update their device by following method(s)
Method 1 (the usual method):
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_aq4501sprout_aq4501/dc78fbefaf5f69cc4754751251d9ece094bc96e6.signed-sprout-mmx-MRA58M-from-LMY48M.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0 :laugh:
Method 2 (using sp flash tool, best method)
This method can be used even if you are running a custom rom. You can also use this method to unbrick Micromax Canvas A1.
Pre-requisites: Windows computer, USB cable, and most important "patience".
Step 1:
a) Download micromax driver.{thanks to @mohsin.r.munshi}
Extract its content, you will find an .exe file inside a folder "driver9401". Disable your antivirus and run the .exe file as administrator. (If you are using 64-bit windows, you will need to "disable driver signature enforcement". Google it)
b) Download SP Flash tool from my mediafire or from its official website. Extract it to any folder
c) Extract the the contents of factory image. [Edit: sp flashtool flashable Android 6.0 is currently not available. I 'll add a link as soon as it is available. I wrote this too early, sorry. For now, if you are running a custom rom, flash official lollipop first and then use method 1 to update to marshmallow.].You will see the following files in it.
Note the location of MT6582_Android_scatter.txt
Step2: Goto the folder where you have extracted sp flash tool. Run flash_tool.exe
Step 3: In sp flash tool, Click on "scatter loading". Then locate and select "MT6582_Android_scatter.txt". SP Flash tool will load all firmware files from the folder where you have extracted the OTA files.
Step 4: Power off your phone. And REMOVE the battery. Now on SP flash tool, click on "Download".
(refer to screenshots given on this website. Ignore the steps given on this website, just refer screenshots)
Step 5: (pay attention to every word) Connect USB cable to your phone only. Then Press and HOLD volume down button and insert the other end of USB cable to your pc. Flashing will start automatically. Wait till you see "OK" message on your pc.
Step 6: Once you see "OK" message, disconnect your phone and reinsert your phone's battery. Turn ON your phone. The first boot will take longer than usual.
Congo! You just updated/unbricked your Micromax Canvas A1.
Feel free to post comments for any doubts and errors
Click to expand...
Click to collapse
BROM error : S_FT_DOWNLOAD_FAIL[4008]
Download to flash fail. Please press ctrl +alt +T to turn on debug log then reproduce again.
Hint- BROM_DLL_V5.log and BROM_DLL.log would be created and record more detail information.
It is showing this error what should i do.?
please reply fast sir.
MayankGupta said:
BROM error : S_FT_DOWNLOAD_FAIL[4008]
Download to flash fail. Please press ctrl +alt +T to turn on debug log then reproduce again.
Hint- BROM_DLL_V5.log and BROM_DLL.log would be created and record more detail information.
It is showing this error what should i do.?
please reply fast sir.
Click to expand...
Click to collapse
I can help you if you provide me more details.
Which phone model you were dealing with? Which rom it it was running before? What were you exactly trying to achieve? Also if possible post the log files here.
xposed
can i have xposed for cm13 marshmallow ?
---------- Post added at 05:34 PM ---------- Previous post was at 04:41 PM ----------
can i have xposed for cm13 marshmallow ?
KadirDvl said:
can i have xposed for cm13 marshmallow ?
---------- Post added at 05:34 PM ---------- Previous post was at 04:41 PM ----------
can i have xposed for cm13 marshmallow ?
Click to expand...
Click to collapse
Yes there are xposed for MM.. Just google it.
[url]http://forum.xda-developers.com/xposed/discussion-xposed-marshmallow-t3249095 [/url]
Sent from my sprout4 using XDA Labs
100%&100% working ROOT TWRP Recovery & bootloop restart solution LeTV Le1s x507&x509
TWRP Recovery & root & bootloop restart
solution LeTV Le1s x507&x509 Indian Version
No more brick and bootloop problem
100%tested solution 8s&14s
New Method added
18/05/2016
Backup all internal storage
install pdanet and preloder driverhttps://drive.google.com/file/d/0By_LtpUoEtFzUDNZLW9JeHhhNnc/view
http://pdanet.co/a/
restart pc
Download new Rar filehttps://drive.google.com/file/d/0B5KBP3GG99Q2aU1wNnYwakliUHM/view?usp=sharing?Extract folder Desktop
Go to mobile settings >> About Phone >>
tap Version 7 Times and hit back
U will have a new option just
above the About Phone option called Developer Options
open it and select USB Debugging
Connect the mobile with pc through USB cable
how to unlock bootloder
duble click recovery bat press any key to enter fastboot mode
After it Reboots
close cmd.exe
press shift+right click select open command windows here
Type fastboot oem unlock HIT ENTER
press volume up confirm NOW THE BOOTLOADER IS UNLOCKED
how to install recovery
duble click recovery bat
press A key to Flash recovery img
again press a akey
switch off the mobile press 10 second power key
now mobile is boot loop
dont worry
open sp tool and flash user data
connect ur mobile Screen blank condition and wait for the process to finish
done
Remove usb cable
Most important
after flash userdata dont power on mobile
press volume up+power
first boot
leave both key showing letv logo
How To root
Start the mobile open twrp folder copy the Superuser.zip file to memory
Go to updater app and select reboot to recovery
select Install select superuser.zip swipe to install
done
Q.I completed the procedure as mentioned in tutorial, everything goes well even sptool download, but when I boot to recovery mode to install supersu the phone boots to stock recovery mode and not the twrp mode. Tried atlest ten times but same problem. How I can boot to twrp mode
Answer .after flash userdata dont power on mobile
press volume up+power first boot
leave both key showing letv logo
Video tutorialhttps://www.youtube.com/watch?v=v9X-a1DmU-g
naeem210 said:
TWRP Recovery & root & bootloop restart
solution LeTV Le1s x507 Indian Version
No more brick and bootloop problem
100%tested solution
New Method added
24/04/2015
Twrp.3.0
Backup all internal storage
install pdanet and preloder driver
https://drive.google.com/file/d/0By_LtpUoEtFzUDNZLW9JeHhhNnc/view
http://pdanet.co/a/
Download new Twrp Rar file
https://drive.google.com/file/d/0B5KBP3GG99Q2NUpJSGVhWlB3X1E/view
Extract twrp folder Desktop
Go to mobile settings >> About Phone >>
tap Version 7 Times and hit back
U will have a new option just
above the About Phone option called Developer Options
open it and select USB Debugging
Connect the mobile with pc through USB cable
duble click recovery bat press any key to enter fastboot mode
After it Reboots
close cmd.exe
press shift+right click select open command windows here
Type fastboot oem unlock HIT ENTER
press volume up confirm NOW THE BOOTLOADER IS UNLOCKED
duble click recovery bat
press A key to Flash recovery img
again press a akey
switch off the mobile press 10 second power key
now mobile is boot loop
dont worry
open sp tool and flash user data
connect ur mobile Screen blank condition and wait for the process to finish
done
How To root
Start the mobile open twrp folder copy the Superuser.zip file to memory
Go to updater app and select reboot to recovery
select Install select superuser.zip swipe to install
done
Video tutorial
http://forum.le.com/in/index.php?th...-solution-letv-le1s-x507-new-method-add.1155/
Click to expand...
Click to collapse
Working!! Thanx
Hi , The Sp Tool does not show any progress at all.
I watched the video , connected the phone while it was blank , still SP tool remains stuck in Download forever and the phone keep looping.
Please help thanks
I tied in Windows 10 as well as Windows 7 64bit
csifreeman said:
Hi , The Sp Tool does not show any progress at all.
I watched the video , connected the phone while it was blank , still SP tool remains stuck in Download forever and the phone keep looping.
Please help thanks
I tied in Windows 10 as well as Windows 7 64bit
Click to expand...
Click to collapse
Nevermind, I used the new method you posted , which was x509 and it worked.
Thanks
compatible with Le 1s Eco?
will this method work with LeEco Le 1s Eco version - Le X509 aswell?
Can u give me stock recovery.img please of le eco 1s x509
can install on x501?
strangely i didnt have to flash the user data..maybe because i am in official marshmallow rom
By unlocking bootloader waranty will void?
What is the new method?
csifreeman said:
Nevermind, I used the new method you posted , which was x509 and it worked.
Thanks
Click to expand...
Click to collapse
What is the new method? As my phone is bricked after I used thus now can't do anything, any advice please.
If any one have le 1s related problem and solution or any one want to try new rom or kernal asap then all of u are welcome in our group on telegram so plz join with us
Requriemt
1. Download telegram from play store
2. Just click below link
https://telegram.me/LeSuperGroup
Thanks all of u
otg support or not tell me fast ?????
Twrp
How to install Twrp in letv le1s x507 Android 5.0.2 (Eui 5.5.008S?
Prabhmeet13 said:
How to install Twrp in letv le1s x507 Android 5.0.2 (Eui 5.5.008S?
Click to expand...
Click to collapse
If u want to use custom ROM or Chinese version upgraded version of ROM then u have to upgrade you official ROM version from lollipop to marshmallow (eui 19s) if you don't want to do that and happy with lollipop ROM and stick with it then u have to install kingroot app for rooting mobile ROM
Then install twrp app or fleasify from ply store
Then download twrp version 2.8.6or7 or otherwise 3.0.2
Image file
If you use twrp official app then find with code name x3 (le 1s eco) then application demand u certain permission then do so rest app can do automatically
If u use fleashify then download official twrp image file rename it to recovery. Img. And place such file into ur SD card or internal storage openly (not put such file into any folder )
Rest process can do the app itsalf if you open the app just follow procedure as app demand u
If u have any problem in above process just search in you tube
You can find both app application process
Thanks for read out such long post
sumitgp said:
If u want to use custom ROM or Chinese version upgraded version of ROM then u have to upgrade you official ROM version from lollipop to marshmallow (eui 19s) if you don't want to do that and happy with lollipop ROM and stick with it then u have to install kingroot app for rooting mobile ROM
Then install twrp app or fleasify from ply store
Then download twrp version 2.8.6or7 or otherwise 3.0.2
Image file
If you use twrp official app then find with code name x3 (le 1s eco) then application demand u certain permission then do so rest app can do automatically
If u use fleashify then download official twrp image file rename it to recovery. Img. And place such file into ur SD card or internal storage openly (not put such file into any folder )
Rest process can do the app itsalf if you open the app just follow procedure as app demand u
If u have any problem in above process just search in you tube
You can find both app application process
Thanks for read out such long post
Click to expand...
Click to collapse
when i boot in recovery only show LETV logo and after automatically reboot phone normally i didn't see any recovery in my phone what can i do?
Im not able to flash user data.. actually i unlocked bootloader in my le1s and wen im clicking on boatloder option in twrp it shows device verification failed ur device might work impropely..not able to flash userdata in sp tool option kindly guide me
Sent from my Le X507 using Tapatalk
asif2017 said:
Im not able to flash user data.. actually i unlocked bootloader in my le1s and wen im clicking on boatloder option in twrp it shows device verification failed ur device might work impropely..not able to flash userdata in sp tool option kindly guide me
Click to expand...
Click to collapse
Bro just PM to naneem bro
Just go to 1st page of this trend and click on naeem profile u found PM tab
brom error s_brom_download_da_fail (2004)
nice
Kk
About :Backup your Moto E4's Official Stock ROM in scatter format.
Requirement :- A Moto E(4)
- USB Cable
- MT65xx USB VCOM DRIVERS http://www.devfiles.co/download/0InO9P5m/MT65xx_USB_VCOM_DRIVERS.zip
- MotorolaDeviceManager_2.5.4 Driver Software https://androidfilehost.com/?fid=24269982087012538
- Miracle Tool v2.27a + Loader.exe https://forum.hovatek.com/thread-15700.html
Installing MT65xx USB VCOM Driver :- Right click on the InstallDriver.exe
- Run as administrator
- On driver signature warning click OK
- Driver software installed Now
Installing Device Driver :- Install MotorolaDeviceManager 2.5.4 Driver Software
Miracle Tool Forum :- Download Mircale Tool + Loader
Thread Link : https://forum.hovatek.com/thread-13347.html
Switch Off Device :- Switch off your Moto E4
- Remove its battery
Miracle Tool Stock Firmware Backup Procedure and Device Manager Hook :- Unpack miracle 2.27A (dsmedia24)
- Run Miracle_Loader_2.27A.exe
- If Start button Faded & Non-working
- Close Miracle tool first
- Change your PC Date to 1 July 2016
- Now Again ! Run Miracle_Loader_2.27A.exe
- Within MTK Tab < Select Read
- Boot Selection Boot Select: 8TH Boot
- Tick/Check save as scatter file
- Leave Miracle Tool in This State
- Open Device Manager within control panel
- Resize the Device Manager Window
- Adjust both Miracle Tool and Device Manager window side by side
- Insert USB Cable at one end of the device
- Now insert another end of USB Cable in Desktop/Laptop USB Port
- As soon as you insert the USB Cable in USB Port ! Hit volume up button simultaneously
- Look at the Device Manager Window under COM & LPT
- You will see MTK USB PORT
- When COM & LPT option gone in Device Manager Window
- Suddenly Hit Start Button in Miracle Tool.
(If successfully done ! You will see charging LED but not charging at all)
- Now in miracle tool select all the files except CACHE & USERDATA
- Click on OK Button
- Select Path
- Do not interfere until backup job finish
- Done
Guide For MOTO E(4) All VariantsCredits :@havotek
This even works on the Snapdragon E4's?
mendelgordon said:
This even works on the Snapdragon E4's?
Click to expand...
Click to collapse
you should give a try first.
kartik verma said:
you should give a try first.
Click to expand...
Click to collapse
I can't try anything since my original e4 had ghost touch issues, so I haven't unlocked the bootloader on my new one because I want to keep the warranty
mendelgordon said:
I can't try anything since my original e4 had ghost touch issues, so I haven't unlocked the bootloader on my new one because I want to keep the warranty
Click to expand...
Click to collapse
taking firmware backup doesn't void your device warranty. instead this process doesn't require rooting or unlocked bootloader :fingers-crossed:
isn't it possible to do a spflashtool readback if we have a scatter file ...
---------- Post added at 05:36 PM ---------- Previous post was at 05:27 PM ----------
My device ( woods)(E4) isn't using this chipset ? shouldn't we try to edit a scatter file from the correct chipset and pulling the block map from adb ?
I want to get a valid scatter to do a readback of an unpatched boot image and stock rom using spflashtools and then patching boot with magisk .
Then we could flash back to stock etc etc ...can any of you who rooted woods use terminal or adb and pull the correct mount points so we can create a scatter for the 2GB/16GB woods variant .
KevMetal said:
isn't it possible to do a spflashtool readback if we have a scatter file ...
---------- Post added at 05:36 PM ---------- Previous post was at 05:27 PM ----------
My device ( woods)(E4) isn't using this chipset ? shouldn't we try to edit a scatter file from the correct chipset and pulling the block map from adb ?
I want to get a valid scatter to do a readback of an unpatched boot image and stock rom using spflashtools and then patching boot with magisk .
Then we could flash back to stock etc etc ...can any of you who rooted woods use terminal or adb and pull the correct mount points so we can create a scatter for the 2GB/16GB woods variant .
Click to expand...
Click to collapse
@KevMetal
you can do this by following the main post
it's a miracle dump so obviously you can't make it spflash tool flashable. but our device have newer mtk chipset MT6737M and miracle tool isn't capable of flashing factory images to newer chipset you need a dongle to complete the flashing process. if we make this process more simple than you need to follow these simple steps.
dump firmware with miracle tool. its in .bin format change the extention to .img and this firmware is ready for flashing with fastboot tool.
do not flash these files in fastboot mode *pgpt.img* and "preloader.img*
if you still want to flash pgpt.img the correct way of flashing this file is "fastboot flash partition pgpt.img"
I am unable to backup using this guide as miracle tool fails to detect my phone. I followed the guide thoroughly but the tool shows "Waiting for USB Port..." two times and then "none usbport, maybe driver not installed". My phone shows white LED when I connect it as per instructions in OP.
gururoop said:
I am unable to backup using this guide as miracle tool fails to detect my phone. I followed the guide thoroughly but the tool shows "Waiting for USB Port..." two times and then "none usbport, maybe driver not installed". My phone shows white LED when I connect it as per instructions in OP.
Click to expand...
Click to collapse
Battery must be removed !! When doing backup through miracle.
You have to press vol. Down button multiple times when device is connected with laptop.
Francesco Franz said:
Battery must be removed !! When doing backup through miracle.
You have to press vol. Down button multiple times when device is connected with laptop.
Click to expand...
Click to collapse
I did remove the battery. Also, do you need to press the volume up button or down? I pressed the start button as soon as COM & LPT disappeared from Device Manager. I also tried to press the volume down button multiple times as instructed by you but still no success.
Can someone please share the stock backup of XT1760 taken using this method?
gururoop said:
Can someone please share the stock backup of XT1760 taken using this method?
Click to expand...
Click to collapse
why did you brick while flashing recovery ? didn't you make a backup before flashing ? either way since there are so many SKU versions it would be better to make your own backup .
if your phone isn't booting after twrp it is because you didn't flash the no dm-verity zip
if the one you got isn't working try the no dm-verity and good instructions for installing in my thread for SKU xt1762 ....
to reboot to recovery hold power and volume down ...you won't go directly to recovery but first to bootloader ...using the volume key "scroll" until you see it says recovery and select that option using power button
when in recovery flash no dm -verify zip
don't flash stock files from my post cos I think they might not be cross compatible between variants for stock only custom roms .
otherwise download a scatter file and stock rom from google and the interwebs and flash your phone using sp flashtools and scatter file .
KevMetal said:
why did you brick while flashing recovery ? didn't you make a backup before flashing ? either way since there are so many SKU versions it would be better to make your own backup .
if your phone isn't booting after twrp it is because you didn't flash the no dm-verity zip
if the one you got isn't working try the no dm-verity and good instructions for installing in my thread for SKU xt1762 ....
to reboot to recovery hold power and volume down ...you won't go directly to recovery but first to bootloader ...using the volume key "scroll" until you see it says recovery and select that option using power button
when in recovery flash no dm -verify zip
don't flash stock files from my post cos I think they might not be cross compatible between variants for stock only custom roms .
otherwise download a scatter file and stock rom from google and the interwebs and flash your phone using sp flashtools and scatter file .
Click to expand...
Click to collapse
No, I didn't brick my device. Actually, I wasn't able to backup my stock ROM using this guide, so I flashed TWRP and backed up my stock ROM using that. I just need stock backup so that I can go back to pure stock if required.
gururoop said:
No, I didn't brick my device. Actually, I wasn't able to backup my stock ROM using this guide, so I flashed TWRP and backed up my stock ROM using that. I just need stock backup so that I can go back to pure stock if required.
Click to expand...
Click to collapse
if you backed up using twrp why would you need pure stock ? there is very little chance you would need stock recovery and boot because you are way more likely to get Oreo via custom rom .....the backup you made in twrp is more than enough in my opinion ...anyways
KevMetal said:
if you backed up using twrp why would you need pure stock ? there is very little chance you would need stock recovery and boot because you are way more likely to get Oreo via custom rom .....the backup you made in twrp is more than enough in my opinion ...anyways
Click to expand...
Click to collapse
The main reason is stock recovery, even stock boot was backed up by TWRP. Stock phones get higher rates while reselling.
There is an OTA update notification in my XT1760 in India. Can anyone please share the stock recovery?
gururoop said:
There is an OTA update notification in my XT1760 in India. Can anyone please share the stock recovery?
Click to expand...
Click to collapse
Which patch?
gururoop said:
I did remove the battery. Also, do you need to press the volume up button or down? I pressed the start button as soon as COM & LPT disappeared from Device Manager. I also tried to press the volume down button multiple times as instructed by you but still no success.
Click to expand...
Click to collapse
@gururoop
Buddy here you done a small mistake. Also you don't bother to read whole thread in a respective manner just scrolling and scrolling. When COM & LPT disappear from device manager. You need to press start button in miracle tool not the vol. Down or up or power button any more. As present COM & LPT port disappears a new port has been established as soon as you press the start button in miracle tool. In first attempt COM &LPT contain MTK USB Port driver as soon as it's removed a new port appears, the actual driver software we need MTK Preloader usb com port#7. Hope you understand it very well
Francesco Franz said:
@gururoop
Buddy here you done a small mistake. Also you don't bother to read whole thread in a respective manner just scrolling and scrolling. When COM & LPT disappear from device manager. You need to press start button in miracle tool not the vol. Down or up or power button any more. As present COM & LPT port disappears a new port has been established as soon as you press the start button in miracle tool. In first attempt COM &LPT contain MTK USB Port driver as soon as it's removed a new port appears, the actual driver software we need MTK Preloader usb com port#7. Hope you understand it very well
Click to expand...
Click to collapse
I read the OP thoroughly and followed the instructions to the letter. But somehow I failed to backup my device. That is why I have been continuously requesting you to share the stock backup if possible for you. Please oblige if not too inconvenient for you. We are here to help each other.
Hello guys,
can I use this method for my moto XT1771. My Androind version is 7.1.1 .Thanks.