Develop Bugs

Any consensus on the best aftermarket tempered glass screen protector?

Firstly, I have read through many of the threads existing on protectors.
When I checked YouTube to see if there were any videos comparing screen protectors for the OPX there were none, so I watched a video comparing 4 screen protectors for a different phone. Of these Armorz and Bodyguardz protectors seemed to come out on top, and survive the strenuous tests the videomaker put them through. It seems neither of these brands make protectors for the OPX.
Next I searched this forum and read through many of the threads on the different screen protectors. For as many people that promote the different protectors, there seem to be as many if not more detractors, complaining of rainbox effect, the protector fitting one OPX but not another, air bubbles, etc.
I ordered my OPX today, and I intend to order a Spigen OnePlus X Case Rugged Armor Black but I was hoping to compliment that with a screen protector.
I was hoping to order the best protector, that will fit my OPX, no rainbox effect, and that will not cause any isue with the Spigen Case - does this exist?

Simple answer is it depends on luck.
I have tried several including 1+, Nillkin, generic, full cover... None of them are perfect, if you go for any like the official 1+ one where only the display is covered you may end up with horrid air bubbles around the cover, many people complained of this-I only know of one guy who done it flawlessly. The plus side of this is that cases will fit fine. The full cover one is the best one I've tried, though it has a rainbow effect in the middle of the screen which can be seen under bright light conditions or on a white screen. This screen protector doesn't have any air bubbles and fits great, only downside is the rainbow, some cases should fit fine e.g. I use the Nillkin frosted back cover which fits without issue.
For me the small rainbow is something I can deal with unlike the air bubbles around the whole display which were an eye sore, you'd be lucky if you didn't get any. So it is hit and miss tbh, just trial and error, I wasted a good £20 on protectors for this phone, which is something I'll never do again.

In the end I ordered from Amazon:
OnePlus X Screen Protector,Nillkin®[Anti-Explosion ][With Camera film][With Back Protector]Amazing H+Pro 9H Tempered Glass Screen Protector for OnePlus X
You mention the protector you use covers the whole phone, but the thing is that I also want the added protection of the Spigen OnePlus X Rugged Armour.
Accepting that they all have flaws, as I can probably still cancel my order and change it, and considering I want front screen protection AND the Spigen Rugged Armour case, do you think I would be better with a different protector than the Nilkin?
*Air bubbles are the main thing I wish to avoid, I could live with a Rainbox effect, once it is only visible from certain angles etc.?
It is a real shame there are non more protectors, I really was sold on Bodyguardz or Armorz protectors after watching the videos where they were tested, and was disappointed to discover they do not make protectors the OPX. I am guessing they do not think there is enough of a market to make it worth their while.

I had a look at the case and it seems that the Nillkin one is probably your best option, as the case covers the sides and slightly overlaps on the front-full protector covers the whole front so you may get issues with it.
Have a look for yourself, here is the one I bought (and currently use):
http://www.ebay.com/itm/281856280418
This is the issue, you could risk bubbles and use the spigen or avoid them, live with a rainbow and use another case. It's down to luck, you may not get any bubbles or rainbow depending on which one you use.

The first sentence in your reply is not so clear, you are saying the Nilkin it is the best option although I may still have issues with it?
I ordered the protector you linked to on eBay about a week ago, but it will take a few weeks to get here!
I do have my Nilkin H+ protector here, my Spigen Rugged Armor case, and my OnePlus X arrived about 15 minutes ago
I want to try apply the Nilkin cover right away - I will post picture for others - but what is the best method? I read somewhere on the forum that we should make sure to use the 'x method', but I cannot remember what x is?

The full cover protector covers the whole front, I mean edge to edge, so the case may not fit-it may conflict with the glass. The Nillkin one only covers the display/screen not the side edges/bezels so you will have no issues with the protector and case.
I have never heard of the 'x method' so don't know, but the best method I have used is with tape or alignment stickers (your protector may have came with them). So you carefully align the protector with the display, apply the tape so it stays in place, remove the film and just close the protector (like a book), apply some pressure in the centre and leave it for a few minutes. Oh and make sure there isn't any dust before applying the glass, use a microfibre cloth to clean.
Also, just to clear things up-you may have issues with the full cover glass protector (not Nillkin-I gave the ebay link previously), the only issue with the Nillkin one is that if you botch it, you will have an air gap around the whole glass. Though if your lucky you may not.

I think this is the x method:
Chris.nl said:
I'm happy with it. The glass feels better then the plastic stock one.
Use the 'hinge method' to apply the screenprotector.
Click to expand...
Click to collapse
Though I haven't tried it myself.
Please upload some picture of your result when you are done

Used hinge method, still got the rainbow effect. I tried unhinging it a few times and cleaned both the screen and the protector and places it back on but there was always a rainbox effect - the last time I tried removing it the protector cracked

I was suspicious at the time when I tried installing the Nilkin Screen Protector, the plastic film removable cover of the protector was on the OUTSIDE of the tempered glass!!!!
WTF!
I know it was on the outside, and not the inside, because the holes in the glass for the front ear speaker and front camera would only line up when the film cover was on the outside, that is facing me as I looked down at the phone. This was the first tempered glass screen protector I ever tried to install, so I assumed I must be mistaken and continued trying to install.
From the videos I have looked again, it seems that this film cover should always be on the inside of the protector (before being removed), that is, on the side of the tempered glass that will be touching the screen of the phone?

Thanks, yes that is the method, see my comments on how it did not work and how I think they somehow sent me a screen protector with the film cover on the wrong side.

xx

As you can see the plastic film protector is on the wrong side of the tempered glass, well, if you want the holes for the speaker and camera to line up!
http://i.imgur.com/VJU5LC7.jpg"]http://i.imgur.com/VJU5LC7.jpg

Yeah, the film is on the inside, the side that attaches to the screen, peeling the plastic sheet off exposes the adhesive bit which sticks to the glass. Just saw the pictures, bad luck man. I got through like 3-4 protectors before settling-if that makes you feel better.

Then I am not losing my mind! Did you see the picture I posted?
Amazon are refunding me at least. I hate that I could not apply a protector to the brand new screen.
Like I said before, I have ordered the one you recommended but it will take some weeks to arrive, and I think you said it will not fit with my Spigen Rugged Armor case anyway.
Can you recommend any others and I will order now? I am in Ireland so possible options are Amazon UK or ebay, though I guess I can order from anywhere really.

As this device is relatively new (only a few months old) there are not many variations of protectors available. As far as I am aware there is the Nillkin type which covers the screen only and the full cover which covers the whole front. I got the ebay one in about a week (China to London), I chose standard delivery (its free and faster than economy).
Check the image in my post here: http://forum.xda-developers.com/showpost.php?p=65705849&postcount=37
That is the full cover one, I had an issue and got it replaced, now it only has a slight rainbow-but I can live with it.

TIFU - I did not realise the second smaller hole in the Nilkin tempered glass was for the proximity sensor, the camera has no hole...

Best TGSP for Pixel 2?

Hello all,
I'm looking for the best tempered glass screen protector for Pixel 2. I have looked through the List of Google Pixel 2 Screen Protectors and I have searched Amazon too, but the reviews are either fake-5-star-reviews, or generally poor reviews.
Can anyone recommend the best option for a Pixel 2 tempered glass screen protector?
Thank you

I have this one and it's the best IMHO and is case friendly. I can attach some pics for you tomorrow.
https://amzn.to/2Psxbes

Spigen, take your time as it fits perfectly side to side on the visual part of the screen only.

Ia am using This glass and it's my third glas right now. 2 times saved my display.
It fits perfect, it is curved.

munchy_cool said:
I have this one and it's the best IMHO and is case friendly. I can attach some pics for you tomorrow.
https://amzn.to/2Psxbes
Click to expand...
Click to collapse
is it full adhesive and curved on the edge?

koax88 said:
is it full adhesive and curved on the edge?
Click to expand...
Click to collapse
nopes

If you are looking for the best, whitestone dome is probably the way to go. It is expensive though. If you aren't worried about full adhesive and curved so it passes the edge of the display there are a lot more options. Spiegen is good for a lower cost option, but it only goes to the edge of the display and doesn't curve.

Thank you for all the suggestions. I'll definitely use one of these screen protectors

ElaineM said:
Thank you for all the suggestions. I'll definitely use one of these screen protectors
Click to expand...
Click to collapse
avoid those on ebay for under $3 or aliexpress. you'll just waste your time

Keithn said:
whitestone dome .
Click to expand...
Click to collapse
Quick question: do you (or does anyone on the forum) have one of these and can tell me if I can use it in combination with Google's fabric case?
(Also, I am currently in Germany. I can order one, but the translated text on the Amazon listing sounds like a scam. It also claims to "take away blue light". I want my display as intended, not blue-filtered.
FTR, I've been trying to get the "official" SP (Power Support) from the Google store, buy it isn't available in Germany.

boondiordna said:
Quick question: do you (or does anyone on the forum) have one of these and can tell me if I can use it in combination with Google's fabric case?
(Also, I am currently in Germany. I can order one, but the translated text on the Amazon listing sounds like a scam. It also claims to "take away blue light". I want my display as intended, not blue-filtered.
FTR, I've been trying to get the "official" SP (Power Support) from the Google store, buy it isn't available in Germany.
Click to expand...
Click to collapse
I'm currently using one. I think it would fit the Google case, but I haven't tried. I've used it with an OtterBox symmetry, a speigen tpu, and with the moment case with no issues. It covers the full display but still leaves gaps on the edges.
I haven't noticed any significant blue light filtering but I did see that the description stated that. I can try to compare it against another Pixel 2 with a different screen protector and see.

Thanks, that would be nice of you if you could have a look at a second Pixel 2.
FTR, I turned off colour boosting, and really appreciate the near-natural colour provided by Google's OLED settings. I couldn't understand why people complained about the "faded" colours in the beginning. I bought this thing as a camera with a phone, and I want to see my photos as close to what I see while shooting them. Filtering blue light is a bit of a deal-breaker for the glass dome, if perceivable.

I've had 2 Whitestone Dome Glass protectors. The first had to be replaced when my phone slipped through the gap in my pull out couch and when trying to get out it slipped under one of the couch legs, crushing the screen (no screen protector will help in that case). The second came in today, after some back and forth with Whitedome trying to figure out why it was showing out of stock on Amazon, and I had to trash it less than an hour after opening it.
The first one was a hassle to install but once installed I really, really liked it. The second had a broken bottom piece for installation, causing an imbalance in the phone and I went through 3 (one left over from first install) adhesion tubes before I realized that was why a good bit was slipping over the edge of the phone and not across the display. When I realized what was going on I was kind of angry it even happened, wasn't paying much attention, and the protector cracked when I was removing it to try and clean up everything...
I either got lucky with the first or REALLY unlucky with the second, but either way I'm not buying another one. The installation process isn't exceedingly difficult, but it's just way too cumbersome for what it should be, costs too much, and just isn't worth the headache. Really disappointed in it. Luckily Amazon did me a solid and is letting me refund it.
That first was by far the best I found for TGSP's for the Pixel 2. I'm really hoping the Pixel 3 goes back to fully flat glass, not this "it's curved just enough at the edges to make it extra difficult for third parties to make screen protectors" crap.

Follow-up: I tried it and it works with the fabric case, there is stilla gap. @jppowers is right about the installation process, it is a buggerance. I had an air bubble, glue spilled under the protective sticker on the speaker and it was generally cumbersome.
There is some blue light filtering, which makes sense given that the glue is near-UV-polymerised, but my brain compensates this and I don't see it if not in direct comparison with a screen without the protector.

100kaa said:
Ia am using This glass and it's my third glas right now. 2 times saved my display.
It fits perfect, it is curved.
Click to expand...
Click to collapse
Hello,
Does this screen protector actually curves around the 2.5d edge of Pixel 2 or is it just that the edges are sloping to give a smoother feel when finger meets the edge of scren protector, but the actual contact surface side of scren proterctor is flat? Would be awesome if you could share close up pictures of this protector on your phone. I am wondering if this screen protector actually creates no ugly halo effect around the preimeter when applied?

bbdcbb said:
Hello,
Does this screen protector actually curves around the 2.5d edge of Pixel 2 or is it just that the edges are sloping to give a smoother feel when finger meets the edge of scren protector, but the actual contact surface side of scren proterctor is flat? Would be awesome if you could share close up pictures of this protector on your phone. I am wondering if this screen protector actually creates no ugly halo effect around the preimeter when applied?
Click to expand...
Click to collapse
Hi, I took few photos, it seems nice.. just to much of dust found way under the protector

100kaa said:
Hi, I took few photos, it seems nice.. just to much of dust found way under the protector
Click to expand...
Click to collapse
Thank you this one looks interesting, tempted to buy one myself, but maybe you have idea why there is significant amount of dust stuck? Is protector not full adhesive? Could it be that due to contouring it is unable to stick to whole screen surface properly? Misapplied or high-dust environment?

bbdcbb said:
Thank you this one looks interesting, tempted to buy one myself, but maybe you have idea why there is significant amount of dust stuck? Is protector not full adhesive? Could it be that due to contouring it is unable to stick to whole screen surface properly? Misapplied or high-dust environment?
Click to expand...
Click to collapse
Hey, I don't really know what could be the problem. At the beginning everything was OK, but later problem with dust appeared. I am in normal surroundings, with no extra dust. Office-house.
I bought, as reserve, from same guy foil protection also. Maybe it will be better.

When a screen protector only has glue on the edges the dust enters at the speaker openings. I'm still using my original Spigen Glass protector with zero dust since it adheres to the whole screen but doesn't cover the curved sides, the pack comes with 2 protectors and I will swap it out soon as the fingerprint resistance isn't the best anymore(but it's been almost a year).

Whitestone's Dome is definitely the best by far, but just as everyone else has mentioned, the installation process is a massive hemorrhoid. For what they charge they oughta include a professional in-home installation service.
I highly suggest to anyone who gets the Dome, set aside 2 hours, watch the videos online, prep your area, and be extremely patient. Also, make sure you've eaten and haven't had anything that will make you jittery or anxious like coffee, it will make the whole process much easier to handle and you'll be much less likely to fly into a rage if you run into issues.
Also, as mentioned by others, be sure to fully inspect your glass before you attempt to install it. There is a very thin film on the back of the glass to keep it from splintering in the event of a shatter, and sometimes they end up with bubbles between the glass and film during manufacturing. I went through both tubes of adhesive and a lot of frustration before I realized the bubble was not a personal application error but a flaw in the glass. Getting a replacement was no issue, but I still lost two hours and grumbled quite a few choice words.
Caveats aside, it's a superb full coverage TGSP.

tempered glass screen protectors

Okay. Here it is. We can start the debate soon about which screen protectors actually work on this phone without Halo and bubble issues. It is always an issue with these curved glass screens but there are always 1 or 2 screen protectors that people can get to actually work. Please post which ones you have purchased and how well they worked.
Posting without pictures is not helpful to anyone.

Ordered the ones through Amazon from Mr. Shields and the case/protector from HanhuaTech. The Mr. Shields order gave me 3 and all 3 were nothing but bubbles. Never used their stuff before and highly disappointed. The latter was a nice case, but the screen protector has a black ring around the edges and is impossible to line-up so it doesn't cover the edges of the display area. No bubbles though. Just cut off part of my screen. Still looking. The Otterbox Defender does not include a screen protector.

I tried those Mr shield protectors with my v30 and they were garbage.
The supershieldz worked well with my v30 but the v40 version has that stupid black border which means it only has adhesive at the edges and will have the rainbow effect

Guess we're all screwed for a bit. For what this thing costs, I refuse not to have the tempered glass protector, but they all have the black ring or bubbles. Early adopter blues I guess.

Curved screens, like the V40 (and pretty much every flagship phone) have tend to have poor tempered glass adhesion, in my experience. It seems they all utilize only adhesive along the outer edge, leading them to come unstuck extremely quickly and easily. All of the reviewed models on Amazon, likewise, have this problem. Hopefully a good one will come out for this phone at some point reasonably soon.
I know that T-Mobile tried to sell me an overpriced one when I purchased my phone, though I'm not certain they had any in stock yet. If no models come out that stay stuck pretty well, I will take purchase one of theirs, as they will replace it every time I come in the store.

Be patient and wait for IQ Shield LiQuidSkin, best on the market for curved screens. Available mid Nov.

I quite enjoy the bodyguardz one I got. It's aluminosilicate like gorilla glass and does have the black border, however I've seen 0 rainbowing. Also comes with lifetime replacements which I will probably thoroughly abuse.

I just ordered a set right from their website. It didn't list that it wasn't in stock and ready to ship, so we'll see!

Don't rush! The earlier you get it, the bigger the risk it's not properly tested yet (especially when it comes to curved screens). This early after release, you're the guinea pig...

While I'm waiting for "IQ Shield LiQuidSkin" I ordered "PULEN Screen Protector"... I'll keep you updated!

I ordered the Poetic tempered glass screen protector. Works like a charm. 3 Days and still sticking no problem. No halo, rainbow effect, etc. Absolutely loving it. Fit is amazing and the feel is as good as the original glass, if not slicker. I'm using it with a Ringke Fusion-X case and they work perfectly together. The screen protector is case friendly and the gap between the glass and case is very minimal.
https://www.amazon.com/gp/product/B07HNNBJLC/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

nyttliv7 said:
While I'm waiting for "IQ Shield LiQuidSkin" I ordered "PULEN Screen Protector"... I'll keep you updated!
Click to expand...
Click to collapse
I know PULEN hasn't got very good reviews, but for now, while waiting for LiQuidSkin, it's all good, fits almost perfect. Nothing I recommend though. The black frame covers a faction of the visibility of the screen (left and right side)
But totally OK. Let's see if it falls off before I get my LiQuidSkin?

tveith said:
I ordered the Poetic tempered glass screen protector. Works like a charm. 3 Days and still sticking no problem. No halo, rainbow effect, etc. Absolutely loving it. Fit is amazing and the feel is as good as the original glass, if not slicker. I'm using it with a Ringke Fusion-X case and they work perfectly together. The screen protector is case friendly and the gap between the glass and case is very minimal.
https://www.amazon.com/gp/product/B07HNNBJLC/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Click to expand...
Click to collapse
I was just looking at the poetic glass on Amazon and can't seem to find a good enough review that specifies it the tempered glass fully seals to the device or only seals around the edges of the glass?

Just heard from Whitestone email support that they do not currently plan on producing Dome Glass for the V40... real shame. Maybe some other V40 owners can chime in to pique their interest?
I was also just looking at the Poetic before I came over here, and also wonder if it is in fact full-adhesive. Anyone?

justinkerng said:
Just heard from Whitestone email support that they do not currently plan on producing Dome Glass for the V40... real shame. Maybe some other V40 owners can chime in to pique their interest?
I was also just looking at the Poetic before I came over here, and also wonder if it is in fact full-adhesive. Anyone?
Click to expand...
Click to collapse
I've been looking at that but but I'm in high doubts it's full adhesive

I just installed the Poetic tempered glass from Amazon and it has a massive rainbow effect. There clearly isn't any adhesive in the middle. Until someone makes a decent one it will have to do.

Blown 89 said:
I just installed the Poetic tempered glass from Amazon and it has a massive rainbow effect. There clearly isn't any adhesive in the middle. Until someone makes a decent one it will have to do.
Click to expand...
Click to collapse
Dang, it seems so difficult to find good tempered glass screen protectors. Poetic seemed promising but glad you confirmed it is not full adhesive, since so many brands don't specify.

nyttliv7 said:
I know PULEN hasn't got very good reviews, but for now, while waiting for LiQuidSkin, it's all good, fits almost perfect. Nothing I recommend though. The black frame covers a faction of the visibility of the screen (left and right side)
But totally OK. Let's see if it falls off before I get my LiQuidSkin?
Click to expand...
Click to collapse
Update!
Amid medium level reviews on Amazon, I have to say I'm surprised this pulen sp is working so well. Some kind of drier than normal glue, covers the whole sp, and if you place it perfectly, it's actually a very nice sp. The black frame slightly covers (1/10 of a mm) of left and right sides, but it really doesn't take away anything, not even the screen off blue notification around the frame. I'm not sure about the physical strength though. I'm a very careful person, never really drop my phone. No rainbow! No dust stuck around the borders. Right now I'm not sure I will order the liQuidSkin? I'm happy with this one

Folks, whitestone dome for LG V40 available for sale @ Amazon :
https://www.amazon.com/dp/B07JQT17Q4/ref=cm_sw_r_em_apa_gAR5BbVS4BYDV

I'm using Key liquid glass screen protector. I can't stand the film protectors so decided to use this. It's a wipe on application, scratch resistant, 9H superior hardness rating, water proof and anti bacterial. Just clean the screen with the included cleaning wipe than apply the liquid screen protector via the included wipe. Let sit for about 5 minutes and you're set.

Good quality screen protector and case?

I usually got Spigen cases for my phones and Whitestone Dome glass, but since this is a flat screen, there will be no Whitestone this time.
I mean, I don't miss it too much because it's really, really expensive. But I do need a good alternative now with this phone.
What screen protector did you guys buy, and which of them worked great? I want to have FULL coverage with good adhesion.
Casewise, well, just post whatever works great.
Ps.: Glass wise I found Nillkin has a few on their website, but I have my doubts.

I got the Nillkin case and glass, quality-wise quite good
and ordered this as a backup .mytrendyphone.eu/shop/full-cover-xiaomi-mi-10t-pro-5g-tempered-glass-screen-protector-261932p.html

LightSmok said:
I got the Nillkin case and glass, quality-wise quite good
and ordered this as a backup .mytrendyphone.eu/shop/full-cover-xiaomi-mi-10t-pro-5g-tempered-glass-screen-protector-261932p.html
Click to expand...
Click to collapse
Thank you, placing my order. I hate how the stock case wont even protect the camera 'hump' lmao. Got some time though, have a week until unlock is done.

I ordered a Nillkin Amazing H+PRO. Have that one on my Mi Mix 2S so went with it again.
I don't plan to buy any case since I actually like the one that comes with the phone.
Seems to me that the Xiaomi cover is slightly higher than the camera so when you have it on the table the camera is not touching the table so perhaps it does protect the camera a little bit but I am not sure.

I regret buying a screen protector, should have just let the pre applied factory film be on the phone. When I installed the screen protector there was a white dot inside a air bubble which was annoying so I removed the protector and removed that white dot but then when I put the protector back on there was more bubbles and a black dot appeared in the middle of the screen so I ended up buying a new tempered glass protector but from a different brand. So disappointed because when I applied it to my Mi Mix 2S it was perfect, no bubbles or anything.

Question Screen protector question

Are there any issues with having a screen protector on this curved screen? Are they harder to put on? Do they tend to come off? I'm trying to decide between getting the Pro or the regular version. I know in the past there were issues with curved screens. In addition to what's mentioned above, the screen protectors for curved screens didn't provide complete coverage. TIA

If your happy with none tempered glass then curved isn't a problem. I've still got the one that came with my devices and have no issues with keeping it on for as long as possible

There some nice uv light glue +tempered glass on aliexp, i'm waiting for mine, i had curved displays before and it's the best you can get, the glue is really there to be on all the surface nad even on the curves, i'm tempted to install some s20+ protector on my 9pro because it's the same size nad curves, till the ones i'm waiting for arrives

It's ok, but my devices prefer naked...

Chinaroad said:
There some nice uv light glue +tempered glass on aliexp, i'm waiting for mine, i had curved displays before and it's the best you can get, the glue is really there to be on all the surface nad even on the curves, i'm tempted to install some s20+ protector on my 9pro because it's the same size nad curves, till the ones i'm waiting for arrives
Click to expand...
Click to collapse
I've ordered a couple too.
I bought the Spigen NeoFlex from Amazon, they are a TPU protector and they are useless, too flexible to apply easily and also the edges do not stay stuck down to the curve so would pick up dirt and come off easily. I sent back for a refund as not fit for purpose in my view.

I bought the Zagg InvisibleShield GlassFusion+ for my Pro and the normal tempered glass by Zagg for my 9. Both with the eye comfort, micropel bs. The GlassFusion+ is the old school "rubbery" type screen protectors. It definitely feels like glass, but isn't glass. It goes somewhat to the edges of the glass. Maybe stops ⅛" from the actual end of the curve. Bubbles like crazy by the curves. Keep having to smooth them out but they keep showing up. Not sure if it's cause of the screen protector or not. Went to register them with Zagg and had to talk to customer care and it escalated to a supervisor because apparently they're not even in their system yet. Go figure lol

Chinaroad said:
There some nice uv light glue +tempered glass on aliexp, i'm waiting for mine, i had curved displays before and it's the best you can get, the glue is really there to be on all the surface nad even on the curves, i'm tempted to install some s20+ protector on my 9pro because it's the same size nad curves, till the ones i'm waiting for arrives
Click to expand...
Click to collapse
Link?

dalelindley76 said:
If your happy with none tempered glass then curved isn't a problem. I've still got the one that came with my devices and have no issues with keeping it on for as long as possible
Click to expand...
Click to collapse
Are you saying that the phone comes with a tempered glass screen protector and there are no issues with it?

It sounds like for the curved screen the tempered glass is better and for the flat screen you can use TPU. Is that the consensus?

https://a.aliexpress.com/_mP1hlMF
i still cant recommand it yet because didn't receive it, but what i do recommand is a screen protector that come with the glue and uv light, because the glue will be at all the surface, hardens fast, no bubles, and it does not come loose easily

bird333 said:
It sounds like for the curved screen the tempered glass is better and for the flat screen you can use TPU. Is that the consensus?
Click to expand...
Click to collapse
I've not recieved my glass ones, and I'd certainly go with a LOCA/UV glue version as those that are out on Amazon look to not be full glue coverage, some even just have the top,sides and finger print scanner and they look awful.
I can safely say though that I feel a TPU one would be false economy as not only do they offer very little in the way of drop protection, the one I tried didn't fit well at all.

On my 8 pro , I've used a few UV type glued protectors with no issues at all with Whitestone Dome being my favorite for a genuine feel and solid protection. I emailed them and they said later this month for the 9 pro. If you go this route justake sure to put the sticker over your ear piece when applying the glue.

Samuel Holland said:
On my 8 pro , I've used a few UV type glued protectors with no issues at all with Whitestone Dome being my favorite for a genuine feel and solid protection. I emailed them and they said later this month for the 9 pro. If you go this route justake sure to put the sticker over your ear piece when applying the glue.
Click to expand...
Click to collapse
Whitestone Dome was the best I had on previous phones. Thanks for the info on time frame. My factory-installed film protector just started to lift on one edge yesterday so I'm ready to buy a replacement, but I'll probably wait and get one of those.