Related
purchased a insurance replacement from flebay it came with a samsung quick charge plug ,is this the same as a htc quick charge or shall i buy a htc type ?
The Samsung Quick Charger I believe only supports QuickCharge 2.0 while the HTC 10 is QuickCharge 3.0, so it will get the job done just not as fast as a 3.0 Charger. It pulls 5v while the HTC charger can pull 5v, 9v, or 12v.
It should be ok but the only difference is the 2.0 will charge a little bit warmer. Should be relatively the same speed as 3.0 but just get a bit hotter. So there shouldn't be any issues
Quick Charge 2.0 and 3.0 both charge at the same maximum speeds.
The difference between the two of them is that Quick Charge 3.0 allows for smaller drops in voltage as the battery get more full, allowing the charger to remain closer to its maximum charging speed for longer.
Instead of dropping right from 12V to 9V as the battery fills up, it drops from 12V to 11.8V to 11.6V etc.
Hi guys, the Zenfone 3 deluxe supports qualcom quick charge 3.0 however it seems to be locked to the oem charger. Any other licenced qc 3.0 charger does not quick charge the phone. How hard would it be to get around this? Mainly for qc 3.0 powerbanks.
Huffy1 said:
Hi guys, the Zenfone 3 deluxe supports qualcom quick charge 3.0 however it seems to be locked to the oem charger. Any other licenced qc 3.0 charger does not quick charge the phone. How hard would it be to get around this? Mainly for qc 3.0 powerbanks.
Click to expand...
Click to collapse
This is not true. I am using this one - https://www.amazon.de/gp/product/B01EH11AS8/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
and the quick charge 3.0 works fine. I am still using the original type-c cable that came with the phone though.
Note: Make sure that you have plugged in the USB end of the charger correctly, push it all the way in. If it's only pushed in partially, then you may not be getting the full power for Quick Charge. You can verify this by using a tool like AIDA64 from the playstore and checking the "Charge Rate" under battery.
This is where I was told it's not supported.
wap.ithome.com/html/262150.htm
Does it say Fast charging on the lock screen?
Huffy1 said:
This is where I was told it's not supported.
wap.ithome.com/html/262150.htm
Does it say Fast charging on the lock screen?
Click to expand...
Click to collapse
Update: Sorry guys, I realized that the OEM charger is indeed much faster at charging. Read posts below.
postimg.org/image/6wis1rux1/ - using licenced qc3.0 charger
postimg.org/image/ndr13s0pv/ - using oem charger.
Further test screen off
15min charge with licenced qc3.0 gives 13%
15min charge with oem charger gives 27%
Same test with screen on (playing video)
15mins with either charger yields about 15%, no noticible difference. Seems like the oem charger throttles when screen is on.
All tests are run when the battery is below 20%.
Same oem cable used for all tests.
Using the oem charger to fully charge my phone does it nearly twice as fast as the qc3.0 charger.
Don't know how your able to achieve the same speed regardless of charger
Hi guys, I've been experiencing the same problem with original charger, that's very big and it's seems that didn't have quick charge. I've a samsung charger and with samsung charger it wroks fine. I'll try to well plug thw original , but, it's thinner samssung's one.
Huffy1 said:
postimg.org/image/6wis1rux1/ - using licenced qc3.0 charger
postimg.org/image/ndr13s0pv/ - using oem charger.
Further test screen off
15min charge with licenced qc3.0 gives 13%
15min charge with oem charger gives 27%
Same test with screen on (playing video)
15mins with either charger yields about 15%, no noticible difference. Seems like the oem charger throttles when screen is on.
All tests are run when the battery is below 20%.
Same oem cable used for all tests.
Using the oem charger to fully charge my phone does it nearly twice as fast as the qc3.0 charger.
Don't know how your able to achieve the same speed regardless of charger
Click to expand...
Click to collapse
Interesting ... I stand corrected now regarding the "Fast Charging" on the lock screen.
I never used the original charger because I bought mine directly from Taiwan which has an US plug which I cannot use here in Germany directly without an extension.
I tried the OEM charger now with an adapter and yes you are right, the Charge Rate with the OEM charger is 2 times faster than with other chargrers.
OEM charger - 2900ma charge rate
Other charger - 1300ma charge rate
---------- Post added at 11:29 AM ---------- Previous post was at 11:02 AM ----------
Actually now I'm confused. When I plugged in the OEM charger, it said "Fast Charging" for a short while and then it says "Charging". The Charge rate also came down from 3000ma to 1300ma and down to 800ma when the battery is at 90%.
I will do some proper tests with the different chargers and post back.
Confirmed: OEM charger is much faster than other QC 3.0 chargers
When the phone reaches 70-80%, the charging rate will slow down and just trickle charge. This is normal as it can be dangerous to keep charging at Fast speeds when the battery is close to full capacity. So if your phone has 80% and you put it on charge, it will not Fast charge regardless of the charger you use.
Huffy1 said:
When the phone reaches 70-80%, the charging rate will slow down and just trickle charge. This is normal as it can be dangerous to keep charging at Fast speeds when the battery is close to full capacity. So if your phone has 80% and you put it on charge, it will not Fast charge regardless of the charger you use.
Click to expand...
Click to collapse
Thanks for the information
I can also confirm fast charging doesn't work with my QC 2.0 charger. Interesting thing to note is it outputs 5V - 2A and 9V -2A. My guess is this charger from Asus that fast charges the Zenfone 2 would work on our phones because it has the same outputs if you read the description. It's worth a shot and you could always return it to Amazon if it doesn't work.
http://store.asus.com/us/item/20150...nFone+2+&+T100CHI+18W+Power+Adapter+and+Cable
Also sold at Amazon
https://www.amazon.com/ASUS-Charger-Zenfone2-T100CHI-Retail-packaging/dp/B00XR0FBYK
It would be nice to remove the red light when the phone is charging. Maybe it's something that can only be removed after rooting?
pacattack81 said:
I can also confirm fast charging doesn't work with my QC 2.0 charger. Interesting thing to note is it outputs 5V - 2A and 9V -2A. My guess is this charger from Asus that fast charges the Zenfone 2 would work on our phones because it has the same outputs if you read the description. It's worth a shot and you could always return it to Amazon if it doesn't work.
http://store.asus.com/us/item/20150...nFone+2+&+T100CHI+18W+Power+Adapter+and+Cable
Also sold at Amazon
https://www.amazon.com/ASUS-Charger-Zenfone2-T100CHI-Retail-packaging/dp/B00XR0FBYK
It would be nice to remove the red light when the phone is charging. Maybe it's something that can only be removed after rooting?
Click to expand...
Click to collapse
Unfortunately, even though the charger referenced above has the same outputs it doesn't fast charge. Seems you can only fast charge with the included charger. At least we can use our own charging cable. If anyone gets another charger to fast charge the device let us know. It doesn't appear Asus sells the included charger on it's webpage yet.
Not allowing the standard quickcharge charger to work forces people to once again purchase / replace current QC chargers.
One tick to the CONs side of the evaluation.
ewingr said:
Not allowing the standard quickcharge charger to work forces people to once again purchase / replace current QC chargers.
One tick to the CONs side of the evaluation.
Click to expand...
Click to collapse
At this moment, I don't really think it's a CON side...
The quality of all those QC2.x/3.x charger are not even today (may get better in future, however I really doubt those cheap, knock-off charger from China). Some are good, some are outright bad. QC is quite sensitive with the voltage/current delivered by the charger (it's by design of QC, I believe) and not optimum voltage/current will shorten the battery life at best, create danger at worst scenario.
LiPo battery is really not designed to be charged in high speed. The associated temperature issues needs to be check very carefully and charge current needs to be controlled strictly to avoid dangerous thermal runaway. It cannot only be done by phone itself and need co-work from adaptor (switching voltage, for instance.) Thus an adaptor which have good communication with phone is a safety requirement as far as QC is concerned.
Same with me. I bought a wall charger aukey PA-16 and a car charger Aukey CC-T8. Using the ampere APP, The original zenfone charger gets 2800 mAh. And the aukey chargers up to 1300 mAh.
K6 charger also does not enable Quick Charge function on 570KL
Input type: 100-240V 50-60Hz 0.5A - Quick charge 3.0 output: 3.6V-6.5V-3A/6.5V-9V-2A/9V-12V-1.5A - Power: 18W
I am wondering if someone achieved any solution to remove OEM charger lock to use fast charge with third party Qualcomm Certified Chargers/Power Banks?
Sorry to resume this thread but i lost my oem charger and id like to get one that works with the zenfone 3 deluxe and quickcharge. Can anyone post a link where i can buy it or maybe the model number of the charger? The EU version would be nice.
Thanks
Any solution to the original question?
pacattack81 said:
I can also confirm fast charging doesn't work with my QC 2.0 charger. Interesting thing to note is it outputs 5V - 2A and 9V -2A. My guess is this charger from Asus that fast charges the Zenfone 2 would work on our phones because it has the same outputs if you read the description. It's worth a shot and you could always return it to Amazon if it doesn't work.
http://store.asus.com/us/item/20150...nFone+2+&+T100CHI+18W+Power+Adapter+and+Cable
Also sold at Amazon
https://www.amazon.com/ASUS-Charger-Zenfone2-T100CHI-Retail-packaging/dp/B00XR0FBYK
It would be nice to remove the red light when the phone is charging. Maybe it's something that can only be removed after rooting?
Click to expand...
Click to collapse
ASUS locked the fast charge function to the OEM QC 2.0 charger that comes with the phone (it will NOT work even with other ASUS QC 2.0 - or 3.0 - chargers, only with the specific type/"model" that came with the phone). Therefore we don't get QC3.0 - as advertised - at all. The QC3.0 compatibility with 3rd party chargers, powerbanks and car chargers was disabled with one of the updates, I think it was the Android 7.0 Update (that replaced Android 6.0) that removed QC3 compatibility. So... any ideas how to re-enable the QC 3.0 functionality?
Quick charge was disabled for other chargers from day one. I'm still on marshmallow (Android 6.0) and only the charger that came with the phone works with quick charge.
I use a 'Dell AC Battery Charger Adapter USB-C470-ABSF Dell 45W 20V 2.25A' for charging my laptop. Can i also use this charger for the LG V20?
I'm using the one from my Asus Chromebook.
Somebody knows which QC 3.0 charger is compatible with the LG V20?
JuiceBitz in the UK...
Their v3.0 23W charging brick, along with their USB A-C cables work fine with my newly aquired V20.
My V20 charging doesn't slow down if I have a 'normal' USB 2 lead charging another device in the other slot either...
Sony UCH12W will work. I also use Ugreen Quick Charge 3.0 charger. It works fine
I have one Quick Charge 3.0 charger (poweradd) and one USB PD (iclever), and (according to systempanel2) they all charge at about the same rate. Max ~1 A while the screen in on (usually throttled at ~500 mA, I'm using a modified thermal config file), and ~3 A while the screen is off. So your 2.25 A charger should work fine, just won't be quite as fast as a QC 3.0 or PD charger.
Hi everyone!
I have a car charger for my old phone, the OnePlus 3. But yesterday my Samsung Galaxy s8+ arrived and is now my daily driver .
My question is : Does a official OnePlus car charger (with dash charge) works for my Samsung Galaxy s8+? If so, does it damage the battery?
Kind Regards,
Pieter
I have tried mine with the old OnePlus dash charger and though it works, the charge speed is crazy slow. The phone was reporting that from about 40% it would take 5 hours to finish the charge.
Am guessing there is something propitiatory in the dash charger that is causing this. I dont use it on the S8 anymore, incase its damaging the battery somehow.
pieterandroid said:
Does a official OnePlus car charger (with dash charge) works for my Samsung Galaxy s8+? If so, does it damage the battery?
Click to expand...
Click to collapse
It won't damage the battery, but it also won't do fast charging as the Dash charging is proprietary and doesn't support Qualcomm's (also proprietary but much more widely used) Quick Charge 2 (or higher; QC is backwards compatible) that the S8/S8+ uses.
According to the car Dash Charger specs the standard (non-Dash) charge supports up to 5V at 2A, which is 10W. Compare this to the official Samsung charger's 9V at 1.67A (QC2), so provides 15W.
Shaady said:
from about 40% it would take 5 hours to finish the charge.
Click to expand...
Click to collapse
In theory then it should be able to charge the S8+ at two-thirds of the speed of the official charger, however it is possible there are other incompatibilities that slows it down - ie. the Dash charger won't provide the full 10W for some reason. A possibility might be the Dash charger cable, as from what I understand this is a bit different to a normal cable to support the Dash charging technology. Maybe try a high-quality standard USB and see if it charges any faster?
An aside: The S8/S8+ is the fact it can also fast charge over (the non-proprietary) USB Type C with 5V at 3A (also 15W). This isn't USB Power Delivery (USB-PD), just the 15W allowed by USB Type C, and since that can provide the full 15W the phone can use over QC2 there's no actual need for USB-PD - but most charges that support 5V at 3A are labelled as providing USB-PD and will work with the phone even if the phone don't use the 'PD' part of the spec.
Lots of questions here...
G7 comes with QC 3.0 although the chipset can support QC 4.0 as per Qualcomm. I see on other forums that users can tell when their phone is quick-charging or slow-charging.
1) Does the G7 let you know what speed it is charging at? I'd like to know so I can swap out cables, chargers, Qi pad, to get the fastest charging rate.
2) Is there a difference between Samsung's Fast Charging, and Qualcomm's QC 3.0?
3) If a charger says that it is compatible with Samsung S9's or S9+'s fast charging, will it fast charge the G7?
4) is there a QC Qi pad that is compatible with our QC 3.0 phone? If so, can I assume that I would still need to power it with a QC 3.0 wall wart?
5) Will a USB-PD or USB-IF charger quick charge our phones?
6) What is the minimum QC cable type (USB 2.0, 3.0, or 3.1) needed to get the maximum QC 3.0 charge? Does it have to be a 3.1 cable?
7) I've seen that when I put the G7 on my 1st gen Qi pad (5W micro-USB) that the phone screen lights up, and a circle briefly appears with the charged percentage in the center (while phone is on stand-by). If the phone is unlocked and the display is on, a white window telling me it is wirelessly charging shows up and tells me how long until the phone will be fully charged (again, when placed on a Qi pad). It's currently telling me 19 minutes to full charge from 93%. Is there a way to get this remaining-time info while cable-charging through the USB-C port?
Thanks!
andygold said:
Lots of questions here...
G7 comes with QC 3.0 although the chipset can support QC 4.0 as per Qualcomm. I see on other forums that users can tell when their phone is quick-charging or slow-charging.
1) Does the G7 let you know what speed it is charging at? I'd like to know so I can swap out cables, chargers, Qi pad, to get the fastest charging rate.
2) Is there a difference between Samsung's Fast Charging, and Qualcomm's QC 3.0?
3) If a charger says that it is compatible with Samsung S9's or S9+'s fast charging, will it fast charge the G7?
4) is there a QC Qi pad that is compatible with our QC 3.0 phone? If so, can I assume that I would still need to power it with a QC 3.0 wall wart?
5) Will a USB-PD or USB-IF charger quick charge our phones?
6) What is the minimum QC cable type (USB 2.0, 3.0, or 3.1) needed to get the maximum QC 3.0 charge? Does it have to be a 3.1 cable?
7) I've seen that when I put the G7 on my 1st gen Qi pad (5W micro-USB) that the phone screen lights up, and a circle briefly appears with the charged percentage in the center (while phone is on stand-by). If the phone is unlocked and the display is on, a white window telling me it is wirelessly charging shows up and tells me how long until the phone will be fully charged (again, when placed on a Qi pad). It's currently telling me 19 minutes to full charge from 93%. Is there a way to get this remaining-time info while cable-charging through the USB-C port?
Thanks!
Click to expand...
Click to collapse
The charge rate of the phone irrespective of the chargers we use, it is controlled by the stock kernel. When screen is on, it lowers down the amperage (See Ampere App) to keep off the heat, vice versa etc. We need a custom kernel to have the charging amperes to be changed manually which is really cool. If we have a really cool custom kernel, the CPU governors should preset customisable governors (for smooth performance) and for the charge values, just look for a 3A charger, with the Kernel Adiutor change the values. Meaning the benefits of rooting gives us the complete freedom of our Android! If a 4A charger is detected by the kernel manager app, the charge values should show as "upto 4A even with the screen on! Then no need to be jealous of Dash Charging of One Plus!
I think this article will help you out... Breaks it all down... Samsung charger are not the greatest for fast charging but works better than a basic one... Ultimately I would say USB c to USB c with USB PD is your fastest with QC 3.0/4.0 being a close second..
https://www.digitaltrends.com/mobile/how-does-fast-charging-work/
I don't see that wireless fast charging is b supported by the g7 ... That's a Samsung gimmick ... But the Qi standard chargers charge at the same rate as a basic charger... The lock screen always tells you how long until full no matter what charger you are using and it will say fast charging, wireless or just charging... My observations have been around 1.5 hour for 60 percent to full so about 5 hours if dead, great before going to sleep and I missed it in my least few phones
two_cents said:
I think this article will help you out... Breaks it all down... Samsung charger are not the greatest for fast charging but works better than a basic one... Ultimately I would say USB c to USB c with USB PD is your fastest with QC 3.0/4.0 being a close second..
https://www.digitaltrends.com/mobile/how-does-fast-charging-work/
I don't see that wireless fast charging is b supported by the g7 ... That's a Samsung gimmick ... But the Qi standard chargers charge at the same rate as a basic charger... The lock screen always tells you how long until full no matter what charger you are using and it will say fast charging, wireless or just charging... My observations have been around 1.5 hour for 60 percent to full so about 5 hours if dead, great before going to sleep and I missed it in my least few phones
Click to expand...
Click to collapse
Thanks! I noticed you do not have a G7 listed as a current phone in your signature. Is your answer above based upon your experience with Samsung phones and their charging system, or specifically with the G7 (or other QC 3.0 phones)?
I hadn't notice the charging speed on the lock screen, as I have the phone set to basically bypass it all the time (fingerprint, facial recognition, & geo-fence)...so I didn't even know it was listed there on the bottom. Thanks again...now I know it's there
Strange thing is I went through a bunch of permutations with cables (various generations), and charge blocks and Qi pads this morning, and with the phone starting at 93% charged, it made no difference in remaining charge time no matter what combination of the items I hooked up. I saw the standard "charging" memo with some combos, and the "fast charging" one too, with others. Can I assume that even though the phone might say it's fast charging, it ramps the speed/power level up and down as necessary due to the current state of charge, or heat or some other factors? Would it also possibly switch into fast-charging with more power if the phone was starting at a lower state of charge, or possibly cooler?Yes, I'll have to read the link above as it's probably covered there
"Fast Wireless Charging" is supported and working.
I have a RavPower 15w and 3 umdigi 15w qi wireless pads that all say wirelessly fast charging when connected. Needs an 18w QC2-3 charger for the input voltage ranges needed to work.
It is noticeably faster than a 10w qi pad and only slightly slower than QC 3.0 USB average charge.
Sent from my LM-G710 using Tapatalk
datafoo said:
"Fast Wireless Charging" is supported and working.
I have a RavPower 15w and 3 umdigi 15w qi wireless pads that all say wirelessly fast charging when connected. Needs an 18w QC2-3 charger for the input voltage ranges needed to work.
It is noticeably faster than a 10w qi pad and only slightly slower than QC 3.0 USB average charge.
Sent from my LM-G710 using Tapatalk
Click to expand...
Click to collapse
Of the 2 Qi pads you mention, any preferences towards one or the other (or a different one altogether)? I have an Anker QC 3.0 charger I can connect up to it.
BTW.. I cannot locate a 15W Ravpower pad. What model is it? And is the Umdigi a model Q1?
andygold said:
Thanks! I noticed you do not have a G7 listed as a current phone in your signature. Is your answer above based upon your experience with Samsung phones and their charging system, or specifically with the G7 (or other QC 3.0 phones)?
I hadn't notice the charging speed on the lock screen, as I have the phone set to basically bypass it all the time (fingerprint, facial recognition, & geo-fence)...so I didn't even know it was listed there on the bottom. Thanks again...now I know it's there
Strange thing is I went through a bunch of permutations with cables (various generations), and charge blocks and Qi pads this morning, and with the phone starting at 93% charged, it made no difference in remaining charge time no matter what combination of the items I hooked up. I saw the standard "charging" memo with some combos, and the "fast charging" one too, with others. Can I assume that even though the phone might say it's fast charging, it ramps the speed/power level up and down as necessary due to the current state of charge, or heat or some other factors? Would it also possibly switch into fast-charging with more power if the phone was starting at a lower state of charge, or possibly cooler?Yes, I'll have to read the link above as it's probably covered there
Click to expand...
Click to collapse
My pixel screen went bad and the charging port went bad also... Just got the g7 so I haven't changed my signature or updated my devices...
Samsung Fast charge is basically qc2 ... And standard USB A to C do not support the higher current that USB C to C does... I notice fastest charging with my pixel USB PD charger...
And yes you won't notice as much fast charging from the top 20 percent of the battery to prevent over charging...
for me, from 25% of charge, the fast charge advertisement says 1 hour and 20 minutes (charge fast???????).... if i use a normal charger (not fast), the time goes to 1 hour and 31 minutes. this phone has a charge fast but very low fast
andygold said:
Of the 2 Qi pads you mention, any preferences towards one or the other (or a different one altogether)? I have an Anker QC 3.0 charger I can connect up to it.
BTW.. I cannot locate a 15W Ravpower pad. What model is it? And is the Umdigi a model Q1?
Click to expand...
Click to collapse
I know it's hard from a specs perspective as most are only 75% efficient so the 10w might only be 7.5w and 15w is actually 10w, which is why LG customer services expressly states you must use a 15w QI charger for fast wireless charging. Another problem is the specs aren't always accurate and updated devices might still have old specs listed. I tried a bunch before I found a couple I liked. The mophie streampad+ also does fast wireless charging but is listed as 10w.
The RavPower is a standup charger I use in the office, the other UmDigi chargers I have scattered around the house and in the bedroom.
RavPower: https://www.amazon.com/gp/product/B079C1QLCR
UmDigi: https://www.amazon.com/gp/product/B07DJ56LT5
Did a little charge test from 50 percent
Wireless charger =1h 40m
Stock iPhone charger =1h 14m
Both pixel USB C to C and stock fast charger =1h 2m
I'm in the market for a qi charger that can fast charge my Thinq g7. I see reports of needing 15W but not seeing many out there that have that spec.
I have seen a RavPower one posted here that is said to do it but the price is quite high for that model. Does anyone else have experience with fast charging the thinq g7 with a Qi charger?
I have Samsung Fast wireless charger. This present with S7. Fast charging battery of S7 Edge, S9+. But G7 didn't support fast wireless charging. And charging is slow. So you can buy what you want but charging with this phone will be slow.
I read this topic and wondering how G7 is going to wireless fast charge?
Sent from my LM-G710
Just thought I'd add to this - the charger that comes with the LG G7 ThinQ (Verizon) is labeled with outputs 9V/1.8A and 5V/1.8A. My old HTC 10 charger is labeled 12V/1.25A, 9V/1.7A, 5V/2.5A. I haven't tried it on the HTC 10's charger on a measuring device to see actual power delivery, but at least on the face of it, if it supports those higher voltages and/or amps, you should be able to get faster charging than with the charger out of the box.
On the other hand, faster charging may in part be why the HTC 10's battery lifetime is dismal, and not once have I thought "boy I wish my G7 would charge faster".
Anyone tried qc4.0 ?
According to some sites ThinQ is capable of 27W (9x3) charging. I therefore purchased a Xiaomi 65W charger which outputs 9x3 but the phone charges only with 15W (5x3) so wasted money.
Yes. I bought 3 different chargers and also a watt meter. When charging with screen on max amps is 1A and 6-8wattage. When screen is off it goes up to max 16watt. And it doesnt matter which charger i use.
80min for a full chsrge isnt that good. But think that lg g7 released in 2018?
Vivos IC00 something charges full in 20min. 4000mAh.
Im sick of "..reduced charging speed cause it can in a long term reduce battery......" who gives..? Then if you notice a different is gonna take 3 years and if still got same phone. Switch battery.
Look at Tesla batteries whos battery lost like 10 percent after 30000 km. I mean..come on
Im on 72% now and it says 45min to full.
A specialised site reported it would charge at 27W (9V x 3A) but this is simply not true. The best it can charge is 15W (5V x 3A). Thats it.