Related
i tried to solve my problem for 1 day before i make this thread.i have an unbraded ls ks20 with english rom v10c.i tried to pass a greek rom (v10g vodafone).after flash it and the phone start setup shows me a message "illegal use" so i went back to english rom.since then my phone doesn't conect to the network "no service".everything else works fine .what should i do?did i kill my brand new lg ks20?
i really need help!
Never flashed before - but you need a special file (nv?) that is unique to your phone. If you didn't back that up, yes you killed it ! If you did search XDA for instructions on how to restore it.
You can do this step to find your signal.
1.backup your ks-20 NV file,the file you can backup from firmware.
2.firm ENG rom and chose ERASE ESF.
3.complete the flash,you can go in the system,and find Windag_open.cab install on the device,and open engineer mode.
4.open firmware,only flash nv file,since reset ,you will find the signal.
I do this to find my signal
lol, He loss calibration data from handset!!!! If there is no service after flashing without NV backup, only way to resolve that problem to flash the NVRAM with backup of another handset and correct IMEI and BT address.
To everyone,
If u need .nv2 file, pm me with ur imei no. and email address, i can generate one for you, but the last digit, which is calculated by your phone, would likely to be different and also i can only generate branded .nv2 since i only got branded .nv2 file. It could be work in unbranded phone but just u need to flash a branded rom or hybrid rom to use with it.
thank you raykisi you are the best it works 100%.
LG KS20 Network Problems
Sorry,
My e-mail is [email protected]
I can't help you with only your email address
Read the posts in my signiture pls
LG KS20 Network Problem
I have read it. Again, many thanks, specially to you; everithing from there was very helpfull.
I will give you the IMEI number: 357323-01-137914-1
I have managed to write the IMEI to the phone with QPSt; do i need to do something else?
If i conect back with QPST shows the IMEI (without the last digit)
Unfortunatell i don't have a valid backup for the nv file
Any help will be great
Ths in advance
Hi raykisi,
I still have my .qcn file... but what I'm trying to do is a little bit different: put a KS20 rom on a MS25 mobile (similar mobile that we have here in Brazil).
I tried to recover my network config using my qcn backup but I couldn't...
My phone always shows "No Service".
Tooo bad...
;(
Hope you can help me...
Thanya
What does ERASE EST do? Why would you think this whole procedure will help find the signal? I asked because my KS20 doesn't find any signal in a lot of places but my wife's KS20 does. I am wondering if there is anything I can try to resolve my problem. Thanks.
sam_sun said:
You can do this step to find your signal.
1.backup your ks-20 NV file,the file you can backup from firmware.
2.firm ENG rom and chose ERASE ESF.
3.complete the flash,you can go in the system,and find Windag_open.cab install on the device,and open engineer mode.
4.open firmware,only flash nv file,since reset ,you will find the signal.
I do this to find my signal
Click to expand...
Click to collapse
Hi to all
I have one LG KS20 here..
Version info:
ROM - v10b
Bootloader - v10b
Modem firmware - v10b
ROM date - 2008-03-07
So - I have a problem here.. When I put the SIM card inside and power ON the phone - I can use Wi-Fi but there is no Network... I read a lot here in this forum and find that if somebody flashes the mobile without backup the NV file - problem... So I did not flashed this mobile.. I just take it and when I insert SIM card just nothing happened... After that I checked the IMEI number - its something like 0000023000000<0
Can somebody explain me what and where is the problem and how to solve it...
Thanks in advance
Best Regards
i have the same problem.for three days try to solve it.i use avery way that appears in the forum and general in the internet.i didn't make it.finaly i send it back to lg for service.i wish you good luck.
pacienta said:
Hi to all
I have one LG KS20 here..
Version info:
ROM - v10b
Bootloader - v10b
Modem firmware - v10b
ROM date - 2008-03-07
So - I have a problem here.. When I put the SIM card inside and power ON the phone - I can use Wi-Fi but there is no Network... I read a lot here in this forum and find that if somebody flashes the mobile without backup the NV file - problem... So I did not flashed this mobile.. I just take it and when I insert SIM card just nothing happened... After that I checked the IMEI number - its something like 0000023000000<0
Can somebody explain me what and where is the problem and how to solve it...
Thanks in advance
Best Regards
Click to expand...
Click to collapse
It seems like ur NV is not there.Try using QPST to restore back ur nv2.If u said u didnt flash or reflash ur original ROM then just send it back to LG
Someone can help us??? I need any NV backup from KS20. Who can help us?
SOS
silence.i think there is no solution.lg in greece send my phone back unfixed.because it is unbranded.in greece lg ks20 appears only with vodafone brand.we really need help.
To everyone,
If u need .nv2 file, pm me with ur imei no. and email address, i can generate one for you, but the last digit, which is calculated by your phone, would likely to be different and also i can only generate branded .nv2 since i only got branded .nv2 file. It could be work in unbranded phone but just u need to flash a branded rom or hybrid rom to use with it.
LG KS20 Network Problem after i flashed a EN ROM
Hi Everyone.
My name is Costin.
I have a strange problem. I have flashed the Enghlish ROM, and i have managed to recover the IMEI number bach with the QPST tool but still no network.
Any ideea???
Can someone help me?
I would like to thanks to all the members of this site, was a grea help to onbtain necesary tools for my phone.
You can't simply use QPST to repair your imei complete, you can't repair no network problem in this way to, you must hv a working .nv2 file with you and restore it back, read the posts in my signiture pls
I've just got a new ks20 ... had the rom V10b-00-262-02-10-OCT-21-2007 (OS 5.2.1626.3) ... I tried to update my rom ... but the "LGMDP_1.5_Build_12.13" always show "No phone" under the phone columm ...
I have done the same as the thread " [How To] Connect KS20 with LGMDP + Free Unbranded .nv2" of raykisi ...
I don't know which step I had fault ... plz help me ...
Here what I've done :
1. Install "LG Corona USB Driver" in computer
2. Change necessary settings in engineering menu
At device:
-Enter this code to dialpad: 2676625720#
.....4. Port Setting → 1. Diag Setting → 1. USB Set for Diag → “OK” → “Back”.
.....4. Port Setting → 1. Diag Setting → 2. USB Switching → “LG Composite -DUN, DIAG”.
-press Done and soft-reset the device. (by turn off and on, I did)
3. Install "WinDiag_Open.cab" in the device and soft-reset it ...
4. Plug the usb cab to PC, at this step the PC found 3 new hardware and Installed completely (A port, A usb and ... something i forgot)
5. Run LGMDP_1.5_Build_12.13, click Select port, the LGMDP_1.5_Build_12.13 can found the port COM5 but there's always "No phone" under the phone columm and NONE the Model
I tried 2 time on a XP PC and a Vista Laptop ... Help me ... plz ... I need my nv2 to play with my new device ...
Thanks you very much ...
(my english is bad ... sorry)
btw .. how to know the phone is branded or unbranded ... my phone start up is only LG logo and then Windows Mobile welcome screen and then today screen .... is it unbraded ... it can be waranted by the LG ???
buy a asus zenfone 2 Model ZE551ML 2GB. and I have a problem saying imei sim1 null and sim 2 works without problem I do have version SO 2.19.40.18_20150612
I need help for me.
warteiner said:
buy a asus zenfone 2 Model ZE551ML 2GB. and I have a problem saying imei sim1 null and sim 2 works without problem I do have version SO 2.19.40.18_20150612
I need help for me.
Click to expand...
Click to collapse
Return to seller.
warteiner said:
buy a asus zenfone 2 Model ZE551ML 2GB. and I have a problem saying imei sim1 null and sim 2 works without problem I do have version SO 2.19.40.18_20150612
I need help for me.
Click to expand...
Click to collapse
same condition.. imei 1 is null but 2. imei is working.. any solution..?
t-mobile_mda said:
same condition.. imei 1 is null but 2. imei is working.. any solution..?
Click to expand...
Click to collapse
restored through Root Explorer
Anyone have any ideas? I'm having the same problem here. Null on 1, fine on 2.
EcthelionIII said:
Anyone have any ideas? I'm having the same problem here. Null on 1, fine on 2.
Click to expand...
Click to collapse
have root?
I have same problem. I lost both IMEI and SN.... sim1 not working, sim2- working very well, Now my IMEIs is 004999..... And SN was 111111111, but I can fixed this, now my real SN.
Repair SN:
1. I take mmcblk0p12(this is factory partition) from other Zenfone 2, repack it via ImgExtractor.exe,
2. in mmcblk0p12/PhoneInfoDisk folder i wroted via HEX Editor my SN, mac adress, bt adress, color of device(5J)
3. Pack back via make_ext4fs.exe tooll to mmcblk0p12
4. Then I flashed this mmcblk0p12 via fastboot flash /dev/block/mmcblk0p12 mmcblk0p12
SN, mac,bluetooth adress return back
But I can't repair IMEI. i suppose it lay in config partition(mmcblk0p14), but i can't to find where..... Somebody help?
I was able to get it working with a workaround , I hope it helps u.
Go to /config/telephony/1 directory. Take backup of all files. Delete all files. Reboot phone. Check your imei.
harpreet.s said:
I was able to get it working with a workaround , I hope it helps u.
Go to /config/telephony/1 directory. Take backup of all files. Delete all files. Reboot phone. Check your imei.
Click to expand...
Click to collapse
No, it isn't work, i try this method already earlier.
null imei SIM1
same condition,, null imei sim1
muhammdridwan2007 said:
same condition,, null imei sim1
Click to expand...
Click to collapse
I found method of repair IMEI1, SIM1 became work
1. Need to flash service firmware(it working also with 550ML) https://cloud.mail.ru/public/AFCz/rNo2nbooH Attention, will be factory reset
2.Need to use Digma_SoFia_IMEI_recovery, try to find in google. I can give link, but there description on Russian language and no need to install drivers https://yadi.sk/d/30q9w4KJjvgHd For our device need to set Connection- COM, Port- Intel Android virtual COM Port
Please watch video https://www.youtube.com/watch?v=dDQ2CzoSFQE and https://www.youtube.com/watch?v=545gshHW6QQ
I faced the same problem few days ago. By flashing couple diffent roms the sim1 came back to life!
mandible11366 said:
I faced the same problem few days ago. By flashing couple diffent roms the sim1 came back to life!
Click to expand...
Click to collapse
Can you please explain about those roms and procedures in details
---------- Post added at 09:29 AM ---------- Previous post was at 09:26 AM ----------
BORETS24 said:
I found method of repair IMEI1, SIM1 became work
1. Need to flash service firmware https://cloud.mail.ru/public/AFCz/rNo2nbooH Attention, will be factory reset
2.Need to use Digma_SoFia_IMEI_recovery, try to find in google. I can give link, but there description on Russian language and no need to install drivers https://yadi.sk/d/30q9w4KJjvgHd For our device need to set Connection- COM, Port- Intel Android virtual COM Port
Click to expand...
Click to collapse
Is this tool really working for Zenfone 2 ZE550ML
I need ZE550ML service firmware??
Help me plz , I lost my imei,mac n serial
Protik said:
Can you please explain about those roms and procedures in details
---------- Post added at 09:29 AM ---------- Previous post was at 09:26 AM ----------
Is this tool really working for Zenfone 2 ZE550ML
I need ZE550ML service firmware??
Help me plz , I lost my imei,mac n serial
Click to expand...
Click to collapse
Do you have factory/PhoneInfodisk/PhoneInfo_inf file? If yes, you can recovery Serial number, wi-fi mac,bt mac by editing it with HEX editor, I not sure, you may use even text editor. If no, you should to get this file from other device. Also you should to write your Serial number to factory/PhoneInfodisk/ssn. I suppose you can try to flash this service firmware, this firmware add Virtual Serial COM Port for working Digma sofia recovery tool- thats all.
BORETS24 said:
Do you have factory/PhoneInfodisk/PhoneInfo_inf file? If yes, you can recovery Serial number, wi-fi mac,bt mac by editing it with HEX editor, I not sure, you may use even text editor. If no, you should to get this file from other device. Also you should to write your Serial number to factory/PhoneInfodisk/ssn. I suppose you can try to flash this service firmware, this firmware add Virtual Serial COM Port for working Digma sofia recovery tool- thats all.
Click to expand...
Click to collapse
Firstly thank you,
In short I say,
Mistakenly I erased all the partitions that includes
System,Factory,Config,ADF,ADP using CWM Recovery advance mode .
After that I flashed a stock rom to unbrick the phone from previous bootloops caused by FOTA update on the rooted device. After that my phone booted but no imei and info.
So I think my factory partition is empty as I formated it
And the firmware you provided is for ZE551ML 4Gb Ram variant while mine is ZE550ML 2Gb Ram.
Will flashing this work for my phone or if you can kindly provide me the Digma servicing firmware for my device!
Again thank you
Protik
There's no factory/PhoneInfodisk directory showing in root explorar
BORETS24 said:
Do you have factory/PhoneInfodisk/PhoneInfo_inf file? If yes, you can recovery Serial number, wi-fi mac,bt mac by editing it with HEX editor, I not sure, you may use even text editor. If no, you should to get this file from other device. Also you should to write your Serial number to factory/PhoneInfodisk/ssn. I suppose you can try to flash this serivice firmware, this firmware add Virtual Serial COM Port for working Digma sofia recovery tool- thats all.
Click to expand...
Click to collapse
I also need help with this sim 1 is unavailable, I have reflashed multiple ways (raw, sideload), have written in my imei, tried deleting telephony files and reboot nothing works , I dont see factory/PhoneInfodisk
Protik said:
Firstly thank you,
In short I say,
Mistakenly I erased all the partitions that includes
System,Factory,Config,ADF,ADP using CWM Recovery advance mode .
After that I flashed a stock rom to unbrick the phone from previous bootloops caused by FOTA update on the rooted device. After that my phone booted but no imei and info.
So I think my factory partition is empty as I formated it
And the firmware you provided is for ZE551ML 4Gb Ram variant while mine is ZE550ML 2Gb Ram.
Will flashing this work for my phone or if you can kindly provide me the Digma servicing firmware for my device!
Again thank you
Protik
Click to expand...
Click to collapse
Don't be afraid, you may flash service firmware from my post via asus flash tool from fastboot mode! This firmware need ONLY for activate Intel virtual COM PORT in device manager on PC, for using Phone Tool 191, no need use phone on this firmware . after repair of your imei1 you should to flash user RAW firmware for ZE550ML -that's all. For repair imei1 no need factory partition, both sim card will be become work, simple you will not have your serial number (it will be 111111) and mac addresses will be not sibling from box of phone, they will be random generated. WI-FI and BT will be work on it too
BORETS24 said:
Don't be afraid, you may flash service firmware from my post via asus flash tool from fastboot mode! This firmware need ONLY for activate Intel virtual COM PORT in device manager on PC, for using Phone Tool 191, no need use phone on this firmware . after repair of your imei1 you should to flash user RAW firmware for ZE550ML -that's all. For repair imei1 no need factory partition, both sim card will be become work, simple you will not have your serial number (it will be 111111) and mac addresses will be not sibling from box of phone, they will be random generated. WI-FI and BT will be work on it too
Click to expand...
Click to collapse
Ok thank you, I will try flashing the service firmware on my ZE550ML and then use digma to change IMEI, the pdf is in russian but seem straight forward enough in the images
BORETS24 said:
I found method of repair IMEI1, SIM1 became work
1. Need to flash service firmware https://cloud.mail.ru/public/AFCz/rNo2nbooH Attention, will be factory reset
2.Need to use Digma_SoFia_IMEI_recovery, try to find in google. I can give link, but there description on Russian language and no need to install drivers https://yadi.sk/d/30q9w4KJjvgHd For our device need to set Connection- COM, Port- Intel Android virtual COM Port
Click to expand...
Click to collapse
Perfect this ended up working on my phone (ZE550ML), flash the service file in the link using Asus Flash Tool, connect to Digma, you dont need to intall the drivers. Follow the pdf to change IMEI, use google translate it works good, remember to omit the last number in your IMEI.
Hi everyone ,
(first sorry for my bad english)
i got a g8 rio-l01 with a few problem ( no imei , no sn , no wifi and bt mac adresse) all this problem was solved using the hcu tool
but the biggest problem is the phone boot in a factory mode ,i can see this in the projectmenu>veneer informaton>other info>run mode: factory
so in this mode :
1-i have no shortcut panel and notification panel when i slide from up to down nothing come
2-no signial or network conection
3-in the first home page in the phone i have MMIs app/software upgrade/MMI/projectmenu/MMIa,
in the second one i have runningtest3
in the last one basic android app
4-i can't use keyboard
so i have trayed i think all huawei g8 firmware and nothing change
trayed with DC phoenix methode (the two methode) and same problem
trayed with the original soft (RIO-L01_M105_Board Software_general_Android 5.1_EMUI 3.1_05021TJY) and no change
trayed with l02 ,l03 ,tl00 ,slim6 and cm13 and the problem persist
bootloader and frp are unlocked ,sim too with hcu and phone rooted
if i remove appfac from user data and reboot the keyboard Appears and other app Appears but the phone stay in factory mode with no upper pannel and no network signial
i can use wifi and bt
in fastboot getvar pruduct give msm8916 (it's normal??? the phone is an msm8936)
i think there is a currupted or a missing file or partition
i have all factory flash file
bootloaderimage: huawei_msimage.mbn, MPRG8936.mbn (i don't know how tu use this two files)
fastbootimage: boot.img, ,cache.img ,cust.img ,emmc_appsboot.mbn ,erecovery.img ,frp.img ,fs_image.tar.gz.mbn.img ,gpt_both0.bin ,hyp.mbn ,log.img ,misc.mbn ,modem_st1.mbn ,modem_st2.mbn ,NON-HLOS.bin ,oeminfo.mbn , persist.img ,recovery.img ,rpm.mbn ,sbl1.mbn ,system.img ,tz.mbn,userdata.img ( and all crc file )
any idea are welcome
thank you
Hi again
So after many test ( and break and unbreak the soft many times) by editing prop and conf files, i noticed that the ro.runmode is the command controling the boot mode.
But i don't know were is this command and if it's possibol:
- To force ro.runmode=normal?
- Or any solution to by pass runningtest3 app or to fake the result?
Thank you (any help are welcome i don't worry about bteaking the phone)
Finally the phone is fully dead ?
After many flash factory, stock and custom i decided to find the way to enter to hs-usb 9008 mode and i find,by flashing the phone with cherry honor 4 rom. And the phone rebooted in 9008 mode, than flashed the ddr and the msm8936 file with zte tool. The msm will not finish and the phone reboot in fastboot (with red, green,blue screen) than reflashed factory rom with dc unlocker the phone rebooted normal but with the same problem that i have in the first.
Second try, flashed with cherry, entred 9008 mode,reflashed with zte tool (by error used a bad msm8936 file from lenovo)
And the phone stop working not detected and black screen
Third try, desassemled the phone, removed battery find test point after many risky test,the phone boot again in 9008 mode.
Reflashed with zte tool, enter red green blue fastboot, and decided to reflash all the factory with fastboot flashall méthode to unbrick an msm8916. Fastboot finish with many failed.
The phone rebooted but black screen and blinking led with continus (red,blue, green), not detected in pc, trayed with test point and nothing
I think it's fully dead now
Sorry for all this long text but just to share expérience
Thank you
And no it's not dead ðŸ˜, find the way to boot it again in 9008 mode with shorting two test point
Here we go for other test
السلام عليكم
hello friend
have you tried to flash the OEMINFO partition (if not be careful because the unlocked code of the bootloader will be changed and you need to read the new one with hcu client)
if you dont know how to do, tell me
sorry for bad english I'm not english man
xzanium said:
السلام عليكم
hello friend
have you tried to flash the OEMINFO partition (if not be careful because the unlocked code of the bootloader will be changed and you need to read the new one with hcu client)
if you dont know how to do, tell me
sorry for bad english I'm not english man
Click to expand...
Click to collapse
allrady solved my problem with an oeminfo but it work only single sim i need an other oeminfo with dual sim
thank you
How To Get Oeminfo
makabress said:
allrady solved my problem with an oeminfo but it work only single sim i need an other oeminfo with dual sim
thank you
Click to expand...
Click to collapse
makabress Please clear here how to get oem info and write it.. i m alredy face same problem..
hellowbd said:
makabress Please clear here how to get oem info and write it.. i m alredy face same problem..
Click to expand...
Click to collapse
Hi , i found the oeminfo searching in google. I will try to find it again
hello
i a have the same prolem but i cant find "the service rom" too, my phone is stuck in mode 9008 i tried to do the rom by myself but witouth any succes.... i read in a post that i cant try to put the "Huawei_Honor_Cherry_L04_V100R001C900B150_India_4.4.4_EMUI_3.0_05021SLQ" who has the same structure but cannot flash phone said "bootloaderimage" fail
please anyone can help me? i am 2 months witout phone... sorry about my bad english im a spanish guy
rio-l01 test point
hi, please i can't found rio-l01 test point can you help me
rmili25 said:
hi, please i can't found rio-l01 test point can you help me
Click to expand...
Click to collapse
test point are in the left/right side of the display connector, you can use a small wire to short it
JoseBankai said:
test point are in the left/right side of the display connector, you can use a small wire to short it
Click to expand...
Click to collapse
thank you brother
please i have the same problem ( rio-l01 no service no call ) can you help me please by oeminfo file or other things
excuse me i'am bad in english
still having the same problem, no solution, try to resoldering emmc, processor, voltage are ok, everything works in other board, so the problem is still the **** mode 9800 and the vanished "service rom" (not trully vanished but every service that i call to fix this ask me for a lot of money just to fix 1 phone... not worth it..) hope somebody can explain this at least, and why is happening, maybe one day can recovery my data on thtat phone....
hi..i have hard bricked my asus zenfone 551ml 4gb/32gb.lost bootloader,recovery everything.set was just vibrating and black.then used xSTFS loader and now regained bootloader..but when i try to flash raw image via asus flash tool it shows FAILED(wrong image format).i tried several times but same.it shows my serial no 123456789ABC..now i m really puzzled what to do.as most who bricked their set were succeded by this method here..so what should i do now? i dont have any asus centre here.plz help.thanx
serial number 123456789ABC is normal if you have ever used xFSTK program to reload the entire boot chain.
I gathered from the internet that Asus Flash tool will hang after it reloads the correct serial number. It thinks it is communicating with a phone that has SN 123456789ABC but then at some point the phone switches SN and Asus Flash Tool hangs.
You can get around this hang using several methods
1) restart computer after asus flash tool hangs
2) use second computer to load RAW image after asus flash tool hangs
3) Going into Windows Device Manager and disabling the Android bootloader device then re-enabling it (after asus flash tool hangs)
You can tell Asus flash tool is hanging when you run "fastboot devices" command and you see a device that is not serial number 123456789ABC
RAW image (to my knowledge) is only for xFSTK program.
kaiser4782787890 said:
serial number 123456789ABC is normal if you have ever used xFSTK program to reload the entire boot chain.
I gathered from the internet that Asus Flash tool will hang after it reloads the correct serial number. It thinks it is communicating with a phone that has SN 123456789ABC but then at some point the phone switches SN and Asus Flash Tool hangs.
You can get around this hang using several methods
1) restart computer after asus flash tool hangs
2) use second computer to load RAW image after asus flash tool hangs
3) Going into Windows Device Manager and disabling the Android bootloader device then re-enabling it (after asus flash tool hangs)
You can tell Asus flash tool is hanging when you run "fastboot devices" command and you see a device that is not serial number 123456789ABC
RAW image (to my knowledge) is only for xFSTK program.
Click to expand...
Click to collapse
but it doesnt hang..just shows failed wrong image format
dr.estiack said:
but it doesnt hang..just shows failed wrong image format
Click to expand...
Click to collapse
problem solved...flashed via fastboot
dr.estiack said:
problem solved...flashed via fastboot
Click to expand...
Click to collapse
can you tell us what u have done to fix it??
i am facing something like you, cannot flash using AFT because after i click start on AFT, it always show "Flash image failure (FAILED (wrong image format))"
tried download raw file few time, in case corrupted, different version and different AFT version, run as administrator but still no luck still showing the same error
in fastboot mode, my serial number is looks normal but "bootloader version - unknown"...
i wonder if the phone bootloader have been unlock, so it cannot be flash using AFT.
i am facing some problem with asus zenfone 2 ZE550ML (Z008)
and decided to flash it so maybe the problem will gone...i maybe gonna create my first thread here about it, i hope i can get some help and fix it myself...
kim7tng said:
can you tell us what u have done to fix it??
i am facing something like you, cannot flash using AFT because after i click start on AFT, it always show "Flash image failure (FAILED (wrong image format))"
tried download raw file few time, in case corrupted, different version and different AFT version, run as administrator but still no luck still showing the same error
in fastboot mode, my serial number is looks normal but "bootloader version - unknown"...
i wonder if the phone bootloader have been unlock, so it cannot be flash using AFT.
i am facing some problem with asus zenfone 2 ZE550ML (Z008)
and decided to flash it so maybe the problem will gone...i maybe gonna create my first thread here about it, i hope i can get some help and fix it myself...
Click to expand...
Click to collapse
just send the commands via fastboot...follow the thread
https://forum.xda-developers.com/ze...ked-phone-updating-to-mm-tips-t3452785/page66
dr.estiack said:
just send the commands via fastboot...follow the thread
https://forum.xda-developers.com/ze...ked-phone-updating-to-mm-tips-t3452785/page66
Click to expand...
Click to collapse
you refer to the step "Flashing Firmware Without AFT", right??
because the phone which i wanna flash is not bricked yet, it still can turn ON normally. i just cannot hearing call in and out (not hardware problem since i still can hear and speak if calling using apps like Whatsapp, BBM, IMO or other chat apps). and also the IMEI of SIM 2 is unknown/Null...but the SIM 1 still can be used and the IMEI is there...tried update to latest OTA didnt solved it, so i think maybe need to be flashed using AFT.
so i did not do the steps before it...i wonder if it still OK??...
kim7tng said:
you refer to the step "Flashing Firmware Without AFT", right??
because the phone which i wanna flash is not bricked yet, it still can turn ON normally. i just cannot hearing call in and out (not hardware problem since i still can hear and speak if calling using apps like Whatsapp, BBM, IMO or other chat apps). and also the IMEI of SIM 2 is unknown/Null...but the SIM 1 still can be used and the IMEI is there...tried update to latest OTA didnt solved it, so i think maybe need to be flashed using AFT.
so i did not do the steps before it...i wonder if it still OK??...
Click to expand...
Click to collapse
it was ok for me..my set was hard bricked..even no bootloader..mine is 551ml. i spent 2days searching and found fastboot method other than aft.