Volt is no longer being maintained
Disclaimer
--I am not responsible for bricked devices, dead SD cards, thermonuclear war,
--or you getting fired because the alarm app failed.
Introduction
Uh undervolt uh overclock uh stuff. Yeah
I cannot guarantee that your device will be stable as each chip handles undervolting and overclocking in different ways. If you experience a crash when the cpu is under full load, then that means the voltage is too low for your chip. I have run into that issue and so have my testers and I raise the voltage a tad each time until a majority is stable.
Undervolt is between -100mv to -200mv on the big and little clusters and gpu is -100 to -200mv.
Why the range? Because each frequency has its own voltage level set and has been tweaked.
Features
**Undervolt CPU by -136mv to -226mv
**Undervolt GPU by -100 to -200mv
**Overclock and Underclock
** GPU underclock to 180mhz
** Backlight Dimmer
** Sound Control
(2208mhz and 2304mhz are separate kernels as not everyone can handle those speeds, I personally cannot but a few of my testers could)Still available in old versions but no longer supported
Important
Not everyone will be stable with the undervolts and overclocks but most should be.
For the people who are trying 2208mhz and 2304, The voltage for 1900mhz and above is set to 1.056v (stock) while v2 (2112mhz) is running at .95v
Also for the people running 2208 and 2304, you lucky f**ks....... I cant get over 2112
Telegram Group
Source will be updated soon when I have time
XDA:DevDB Information
Volt, Kernel for the OnePlus 5
Contributors
Zombie
Source Code: https://github.com/UndeadDeveloper/Volt-OP5-OOS-SimpleGX
Kernel Special Features: Undervolting, Overclocking
Version Information
Status: Beta
Created 2017-08-24
Last Updated 2018-04-12
DOWNLOADS
Reserved #2
First
I'll try it
䙉Êû said:
I'll try it
Click to expand...
Click to collapse
Ran into some build issues and voltage issues. Im trying a new build right now and If it passes my test ill upload. LOS version will be a day or two out since I need an LOS tester (im running OOS)
Zombie said:
Ran into some build issues and voltage issues. Im trying a new build right now and If it passes my test ill upload. LOS version will be a day or two out since I need an LOS tester (im running OOS)
Click to expand...
Click to collapse
I'm using Resurrection Remix now and may be I can try LOS ver.
䙉Êû said:
I'm using Resurrection Remix now and may be I can try LOS ver.
Click to expand...
Click to collapse
That would be wonderful. I havent created a telegram group yet for this kernel but Im mainly in the Lightning group. Feel free to join it so I can link you to LOS test builds later and you can report to me with it
https://t.me/joinchat/DkIGAkSHsn4RXgnhCVjtmw
Zombie said:
That would be wonderful. I havent created a telegram group yet for this kernel but Im mainly in the Lightning group. Feel free to join it so I can link you to LOS test builds later and you can report to me with it
https://t.me/joinchat/DkIGAkSHsn4RXgnhCVjtmw
Click to expand...
Click to collapse
Tks for your invitation
Alright. Volt-V1-OOS is out now for download. Pretty stable for me right now
Good job:good: My stats with test build running on balance mode with spectrum.
nadejo said:
First
Click to expand...
Click to collapse
Want a cooker bro..?
Hey, you did it?
Best of luck for this!
Sent from my ONEPLUS A5000 using XDA Labs
Thanks!
Enviado desde mi ONEPLUS A5000 mediante Tapatalk
spectrum with performance profile causes a boot loop, gets to the lock screen then reboots.
going to try performance mode with ex kernel manager and if that does not work will grab some logs.
daleski75 said:
spectrum with performance profile causes a boot loop, gets to the lock screen then reboots.
going to try performance mode with ex kernel manager and if that does not work will grab some logs.
Click to expand...
Click to collapse
Clear data from exkm and or ka as apply on boot has caused crashing for me too just like you described
Alright. So V1 has some issues. Mainly stability. I ran into some of the same issues with Lightning. I am reworking the kernel with a different base. The kernel base I am using now has amazing battery without any voltage or clock tweaks so well see how this turns out. I might not be allowed to release it if the dev doesnt want me using his kernel as a base.
If he doesnt allow it, then ill rework the kernel, again, this time from pure stock for release.
This kernel isnt really for "aw man I want the best kernel"
Its more for proving undervolting can be done on newer devices. Some friends of mine said that it couldnt be done and I wanted to prove them wrong
Zombie said:
Alright. So V1 has some issues. Mainly stability. I ran into some of the same issues with Lightning. I am reworking the kernel with a different base. The kernel base I am using now has amazing battery without any voltage or clock tweaks so well see how this turns out. I might not be allowed to release it if the dev doesnt want me using his kernel as a base.
If he doesnt allow it, then ill rework the kernel, again, this time from pure stock for release.
This kernel isnt really for "aw man I want the best kernel"
Its more for proving undervolting can be done on newer devices. Some friends of mine said that it couldnt be done and I wanted to prove them wrong
Click to expand...
Click to collapse
I hope you get the permission to use it, as you said it has amazing battery and good performance. I use it as my daily driver kernel atm.
If your tweaks can work, this could be even more amazing.
Best of luck!
Sent from my ONEPLUS A5000 using XDA Labs
Zombie said:
I might not be allowed to release it if the dev doesnt want me using his kernel as a base.
If he doesnt allow it, then ill rework the kernel, again, this time from pure stock for release.
Click to expand...
Click to collapse
Allowed ! :highfive::good:
Cheers'
AndroidGX said:
Allowed ! :highfive::good:
Cheers'
Click to expand...
Click to collapse
Thanks man! Your kernel is already a beast ??
Sent from my ONEPLUS A5000 using XDA Labs
Related
Hello XDA peoples, Today, 11/19/13, I update the OP with my _ICED_KERNEL_ vs. MeltDown
ther are two kernel both are samw except one is OCd to 2.2GHz and the other 1.89GHz
the 2.2ghz is labeled as meltdown. Enjoy them both test them both and report back benches bugs or other wise, peace ~Rushing
here are current changes to stock kernel
################
# CHANGE LOG: #
###############
Tested and Safe =]
1. Added =3 levels of OC @ 540MHz overclock to Faux's overclocking to 1890MHz =] YES!!!
the "YES!!!" indicates that I am proud to have contributed to the kernel as I knew I would.
was going to do this along time ago but I was discouraged by the depths of geekdom involved.. haha
2. Added the following SCHEDs in addition to stock
SIO
ZEN
fifo
vr
row
##############################################
Added the following GOVERNORS in addition to stock
badass
pegasusq
savagedzen
brazillianwax
intellidemand
interactiveX
lazy
lionheart
ondemandx
samsung
smartass
wheatley
lagfree
lazy
lulzactiveV2
smartassV2
scary
interactive
################################
3. Added fast charge so device charges faster while on USB like it does on AC = nice
The zip contains the modules needed in /system/lib/modules .
flash only over a UVMC6 build
make a nandroid
just flash and wipe caches in TWRP
full spare-time kernel building lover now,, expect more features to kernel every now and then
ICED_KERNEL.zip
thanks to XDA for all the useful guides I have found
thanks to Cl3Kener for keeping me interested in kernel
thanks to Jamison904
thanks to Faux
thanks to thewadegeek and his good tutorial on kernel building http://forum.xda-developers.com/showthread.php?t=1748297
thanks to eagleeyetom finally found his guide for git. http://forum.xda-developers.com/showthread.php?t=1877040
Check out my Git pages @ hallovveen31 and check the changes I made to the stock kernel at your leisure.
_to kernel devs or beginning kernel devs, click here_
I am still fixing my git hub right now looks like I switched repositories and made a few commits the wrong way like didnt show records quite right because of the mix. however I am going to fix that later I just realized this after looking to see if I made the kernel go to 1.89 ghz while booting up for a faster boot =] so no worries to you up and coming kernel devs I will show you how I did it on git the right way. to regular users this means nothing special to you. git is just a record of the files and text code in those files to share with others, which I def want to do since I couldn't find the coding for oc up to 1890mhz and would love to share that.
https://github.com/hallovveen31
DOWNLOAD NEW KERNEL WITH NEW RLE IMAGE ie no star but a "SHADOW" graffiti .rle
https://sourceforge.net/projects/beastmade/files/ICED_COLD_SHADOW_KERNEL.1.89.new.rle.zip/download
ICED_COLD with new bootup splash- image a.k.a. initlogo.rle
MELTDOWN
get your windows MD5 checker here
http://winmd5.com/
Linux users.. get gtk hash
Enjoy the meltdown..
Thanks to Kl3kener again for giving me some tips ]
WARNING: nothing ever is my fault, period. if this kernel harms your phone because you overclock your device @ 2268MHz for three months, its your fault, duh. Anyway, the device would sleep and cool down.. So you would have to try pretty hard to cause damages...
Mine
Sent from my SGH-M919 using XDA Premium 4 mobile app
DOWNLOAD latest kernel:
ICED_COLD_1890MHz
take it away rushing
Waiting for it!
Hey Rushing, just tried this on top of JMT8 (with super cache wipe/twrp 2.6.1) and WiFi seems to be broken! Toggle in settings will not stay in ON position. Flashed back to twrp 2.6.0 because of your instructions and tried again (no cache wipe),same result. Flashed back to Tiberious 2.1 (no cache wipe) and phone booted up with WiFi on and working again.
mad4some said:
Hey Rushing, just tried this on top of JMT8 (with super cache wipe/twrp 2.6.1) and WiFi seems to be broken! Toggle in settings will not stay in ON position. Flashed back to twrp 2.6.0 because of your instructions and tried again (no cache wipe),same result. Flashed back to Tiberious 2.1 (no cache wipe) and phone booted up with WiFi on and working again.
Click to expand...
Click to collapse
Okay, thanks for testing I likely will never have time to flash all the ROMs and test compatibility.
I will take another stab at it. this time around all the modules will be deleted and replaced
where as in the first version the modules were expected to flash over the old ones which i guess doesnt always werk as leftovers may be uncompatible.
new build 1.1 is up thanks for testing let me know of success or failure please..
the new build works for me on my own ROM.
Wi-fi working fine here but I'm also using Rushing's Shad0w ROM. (1.1 version of kernel)
Just out of curiosity, Rushing, which of your ROMs do you use as your daily on the hercules?
Just tried 1.1 and WiFi still won't turn on with JMT8, obviously compatibility issue between the 2 of some sort. Per @aahz, kernel appears compatible with your roms Rushing. To continue the test, I'm going to flash my Shadow 1.6 nandroid tomorrow and then try 1.0 and 1.1 both just to see (and confirm). Looking forward to your next Hercules rom brother, Later
Aahz Pervect said:
Wi-fi working fine here but I'm also using Rushing's Shad0w ROM. (1.1 version of kernel)
Just out of curiosity, Rushing, which of your ROMs do you use as your daily on the hercules?
Click to expand...
Click to collapse
thanks for the feedback
I flashed a ROM I made for myself the other day. it has some paid apps in it thats why its for me only and has trickster mod apk xposed installer xprivacy xthemeengineand app setting included... interested? I could remove the paid apps and let it go.. i just noticed that the [extra] toggles and battery are green and the settings_icons are regular yet greyed out rather than every color of TouchWix...
could upload it with the new kernel included. looks like I called it liquid shadow... also uploaded a ROM to SF here is before I even post it =] works good so far didnt test blue tooth hdmi out alot of thing but i suspect everything is good and improved https://sourceforge.net/projects/be...D_CRYSTAL_SKULLS_signed_11-12-13.zip/download
http://sourceforge.net/projects/bea...D_CRYSTAL_SKULLS_signed_11-12-13.zip/download
http://sourceforge.net/projects/bea...D_CRYSTAL_SKULLS_signed_11-12-13.zip/download
http://sourceforge.net/projects/bea...D_CRYSTAL_SKULLS_signed_11-12-13.zip/download
Aahz Pervect said:
Wi-fi working fine here but I'm also using Rushing's Shad0w ROM. (1.1 version of kernel)
Just out of curiosity, Rushing, which of your ROMs do you use as your daily on the hercules?
Click to expand...
Click to collapse
thanks for the feedback
I flashed a ROM I made for myself the other day. it has some paid apps in it thats why its for me only and has trickster mod apk xposed installer xprivacy xthemeengineand app setting included... interested? I could remove the paid apps and let it go.. i just noticed that the [extra] toggles and battery are green and the toggles... and the settings icons are regular tw, yet greyed out rather than every color of TouchWix... could upload it with the new kernel included. looks like I called it liquid shadow... also uploaded a ROM to SourceForge with the new kernel will post very soon... here it is https://sourceforge.net all seems good so far not tested bluetooth yet and hdmi out alot of functions are untested but I bet they all work close to perfect.
https://github.com/hallovveen31
Rushing said:
thanks for the feedback
interested?
Click to expand...
Click to collapse
Absolutely, that'd be great.:good:
Aahz Pervect said:
Absolutely, that'd be great.:good:
Click to expand...
Click to collapse
New kernel Over clockable to 1890 MHz plus more governors and schedulers fast charge
I bother you all with an updated OP and kernel
Changed the boot-up-image splashscreen, initlogo.rle, whatever you want call it. No more star rather a bit of graffiti "SHADOW" to match up with my new ROM version of SHADOW =] enjoy
Checking out the new Shadow Mastery ROM and Kernel version...awesome per usual Rushing. :good:
@Rushing bro please can u make this ROM for us I would be n heaven n I'd have ur babies but of course put that beast tweak on it
http://forum.xda-developers.com/showthread.php?t=1847600
Sent from my SAMSUNG-SGH-T989 using Tapatalk
Aahz Pervect said:
Checking out the new Shadow Mastery ROM and Kernel version...awesome per usual Rushing. :good:
Click to expand...
Click to collapse
yeah I see somebody got into the goodies already hehe ]
that was you huh, thanks you like it? no more pentagrams, all gone shadow has seen the light and trying to change for the better. yeah right ]
for everyone else that dont know where it is, here.
Rushing said:
yeah I see somebody got into the goodies already hehe ]
that was you huh, thanks you like it? no more pentagrams, all gone shadow has seen the light and trying to change for the better. yeah right].
Click to expand...
Click to collapse
I definitely dig it. I lean more towards Shadow over Crystal Skulls (theme-wise) so to have an updated version is great.:highfive: It's nice and fast with the new kernel and I like the subtle theme changes as well.
KERNEL UPDATE 2.2GHz
Updated the OP with this /
/
/
ICED_COLD vs. MeltDown 2.268 GHz
bump. this one can be on the first page for a while longer
what 2.2GHz kerenel ?!?
Credits go to @ktoonsez for his kernel sources and KT apps (KTweaker and KTmonitor) :good:
Disclaimer: me no responsible if you use this!
So what is this? KT-SGS4 AOSP-4.4 S4 kernel ported to S4 Active (Intl). What has changed is of course jactive related stuff:
jactive board definitions and kernel config
camera sources and handler functions
some display settings
assorted stuff, can't really remember all the imporant bits
pre 1.0.0 AOSP4.4
Also, i tried to make a unified kernel, i.e. all differences between original and jactive are controlled with code ifdefs. But this haven't been tested as i don't have S4
So what works? So far i have found only one bug, when making or receiving calls i can't hear what the other side is saying and vice versa, i.e. no audio. Call sounds fixed.
Also overclocking the CPU seems to be broken, at least KTmonitor shows CPU to go only up to 1890 even though the clock is set over that value. So that's one thing to work on. I'll try to debug someday next week.
Compiled with linaro-4.7-12.10 toolchain.
This should work on CM11 and AOSP based roms. Personally i have it running on SlimKat (dualboot) and CM11. Just flash the CWM zip. It contains KTweaker and KTmonitor apps, courtesy of ktoonsez. Thanks mate.
Latest version 04.14.2014
Personal experiences:
benchmarks are slower than with CM11 kernel, dunno if it matters...
still it's smooth in everyday use
KTweaker has lots of stuff to tweak, only if i had time...
AOSP4.4/CM11
This one works with CM11 and AOSP v 1.0.0 and later. Don't use with earlier AOSP since this needs newer blobs.
KT-SGS4-KK4.4-AOSP-eur-02.11.2015
Built with Linaro 4.9 2014.09
Beta release
AOSP5.0/CM12
As there is no AOSP5.0 for jactive yet, just use CM12 .
KT-SGS4-LP5.0-AOSP-eur-02.15.2015:
fixed bootloop for now at least
supports ext4/f2fs partitions
KT-SGS4-LP5.0-AOSP-eur-02.11.2015
Built with Linaro 4.9 2014.09
Beta release
TouchWiz
This one works with KK TW roms (well i have tried only WizCyan...). Seems stable with default clocks and even with some OC. But every phone is different in regards OC, so YMMV. KTweaker and KTmonitor included. Do note that Display settings might not work as we don't have Amoled.
Changes ver 01.12.2015
Fixed unresponsive screen bug
Compiled with Linaro 4.9-2014.09
Changes ver 01.03.2015
overclocking works better now
increased touchscreen min limit freq, hopefully removes problem with unresponsiveness
built with Linaro 4.7.12.10
Changes ver 12.15.2014 (BETA)
first version of KT TW kernel for jactive
added KEXEC_HARDBOOT support, works with MultiROM
General notes
Do keep in mind that if you don't set oc settings in boot, you need to use KTweaker app and reset the cpu min and max sliders for the settings to take effect. Even though the app asks if you want to apply the settings, it doesn't update the actual min and max values.
Download here: https://drive.google.com/folderview?id=0BzJzDM42pkRvd1ZtMDZOR1M1OFE&usp=sharing
Github here: https://github.com/spegelius/KT-SGS4
god !!!!!! .... spegelius did it again you beast ... keep up the good work :good::good:
mythi said:
god !!!!!! .... spegelius did it again you beast ... keep up the good work :good::good:
Click to expand...
Click to collapse
Heh, thanks. Sadly there seems to be a bug with call audio, so for test use only at this point. I went through the kernel code and all i can think of to do is to try audio stuff from CM11 kernel, to see if that's the problem. Still, audio works perfectly everywhere else so really hard to say what's wrong...
spegelius said:
Heh, thanks. Sadly there seems to be a bug with call audio, so for test use only at this point. I went through the kernel code and all i can think of to do is to try audio stuff from CM11 kernel, to see if that's the problem. Still, audio works perfectly everywhere else so really hard to say what's wrong...
Click to expand...
Click to collapse
Whats even harder is taking a logcat and ksmg while in a call
mythi said:
Whats even harder is taking a logcat and ksmg while in a call
Click to expand...
Click to collapse
True, but luckily i have two phones and sims (other one is my work phone) so it's easier to debug.
Some progress: it turns out that for some reason es325 codec can't connect to slimbus sink and thus no audio. slimbus has some kt additions, need to debug more. Also i think it would be good to try to build the kernel with some other toolchain than linaro...
spegelius said:
True, but luckily i have two phones and sims (other one is my work phone) so it's easier to debug.
Some progress: it turns out that for some reason es325 codec can't connect to slimbus sink and thus no audio. slimbus has some kt additions, need to debug more. Also i think it would be good to try to build the kernel with some other toolchain than linaro...
Click to expand...
Click to collapse
Hmmm... does it build modules with kernel ?? Ya changing the compiler to maybe the google ndk gcc may fix up some issues but I think u will have alot of pain in debugging files since not all elements that linaro supports are supported by other .... I maybe wrong but ...xxxx
Good job man :good: :highfive:
mythi said:
Hmmm... does it build modules with kernel ?? Ya changing the compiler to maybe the google ndk gcc may fix up some issues but I think u will have alot of pain in debugging files since not all elements that linaro supports are supported by other .... I maybe wrong but ...xxxx
Click to expand...
Click to collapse
Yes, modules are compiled and part of the cwm package. I haven't checked that all required modules are present, but i don't think that's the problem. Gonna be setting up a proper kernel dev env, found a good howto for Eclipse here: http://simonkagstrom.livejournal.com/33093.html. Regular editors just aren't cutting it anymore
ktoonsez said:
Good job man :good: :highfive:
Click to expand...
Click to collapse
Thanks . Luckily i had some experience with LeJay's cm10.2 kernel and cm11 kernel so i knew roughly what parts differ between jf an jactive. Just a matter of diffing those parts (meld is my tool of choice for that kind of work).
This kernel s awesome. It's speeded up my phone. I want to use this regularly has anyone found a way for the phone call sound??
Sent from my GT-I9295 using xda app-developers app
lijoc said:
This kernel s awesome. It's speeded up my phone. I want to use this regularly has anyone found a way for the phone call sound??
Sent from my GT-I9295 using xda app-developers app
Click to expand...
Click to collapse
Not yet. Been debugging and the problem is somewhere in kernel's slimbus communication, it seems es325 codec cannot get audience firmware loaded properly or something...
spegelius said:
Not yet. Been debugging and the problem is somewhere in kernel's slimbus communication, it seems es325 codec cannot get audience firmware loaded properly or something...
Click to expand...
Click to collapse
Ah, found he bug; && should be || when checking if CONFIG_JACTIVE_ATT or CONFIG_JACTIVE_EUR... es325 wasn't configured properly. Now call sounds work. I'll upload a new build after i do some testing first.
Waiting for the upload
Sent from my GT-I9295 using xda app-developers app
Uploading, KT-SGS4-KK4.4-AOSP-jactive_eur-04.19.2014.zip should be online soon.
It's working now. The volume is too low is there a way to increase it?
Sent from my GT-I9295 using xda app-developers app
lijoc said:
It's working now. The volume is too low is there a way to increase it?
Sent from my GT-I9295 using xda app-developers app
Click to expand...
Click to collapse
Hmm doesn't the volume button work? Also what rom are you running?
Volume button works and is on maximum. I am using carbon rom
Sent from my GT-I9295 using xda app-developers app
I am running your AOSP 4.3.1 ROM http://forum.xda-developers.com/showthread.php?t=2621883
I flashed this kernel in recovery, wiped cache and dalvik, but it will not boot. I get the "Samsung Galaxy S4 Active I-9295" splash screen, then it hangs, and hangs, and hangs.
I had to restore back to the version 8 nandroid of that thread. ADB would give me nothing so early in the boot sequence.
Pkt_Lnt said:
I am running your AOSP 4.3.1 ROM http://forum.xda-developers.com/showthread.php?t=2621883
I flashed this kernel in recovery, wiped cache and dalvik, but it will not boot. I get the "Samsung Galaxy S4 Active I-9295" splash screen, then it hangs, and hangs, and hangs.
I had to restore back to the version 8 nandroid of that thread. ADB would give me nothing so early in the boot sequence.
Click to expand...
Click to collapse
Did you read the topic? this kernel is for 4.4
Indeed, it's for AOSP 4.4.x. You propable need to reflash the whole rom to get back original boot.img and kernel modules.
As for the phone sound being too low, dunno. If it was working ok with the original Carbon kernel, that points the problem being in the new kernel. But to my limited understanding, the volumes come from settings outside the kernel... personally i'm running CM11 with this kernel and volumes are ok.
The volume in carbon rom also is the same. I tried the sound mods but it changes all the volumes of system other than the incall volume.
Sent from my GT-I9295 using xda app-developers app
JediKernel This kernel is compatible with stock 5.0.1. I have not tried with others so if you feel so inclined to test on other 5.0.1 ROMs please let us know how it wentSo far this is tested and working on:
Stock 5.0.1
READ, READ, READ before downloading, flashing, or posting questions
***Not all phones are created equal meaning some phones will not handle Overclocking / Underclocking or Undervolting as well as others.***
Features
OC to 2.88GHz
Kernel Version 3.4.0
Advanced Power Emulation
Default Scheduler= CFQ
Default Governor= Ondemand
Default boot set to 2.26Ghz
Built using arm 4.8 toolchain
More...
Github
In my GITHUB you can find my sources and code changes
Credits
Google for Official Source Code
Faux123
Authorship is always retained in my Repos. Please see my git for commit author
Instructions
---FASTBOOT METHOD---
-Download boot.img
-Boot into bootloader
-In terminal: fastboot flash boot (path to boot,img)
-In terminal: fastboot reboot
---ZIP METHOD---
-Download Kernel zip
-Flash Kernel
-Reboot system
Changelog
Code:
01|07|2015-- Initial Release (See Features List)
Downloads
JediKernel 1.0
boot.img -- http://d-h.st/O3D
zip file -- http://d-h.st/5Mjl
Support this Development by clicking the link below --- Thank you
http://forum.xda-developers.com/donatetome.php?u=4488450
Guide to Thread Participation:
Generally speaking, we are a pretty calm group of people, but as with so many other things in life, there are those that evoke a negative response from the very start. THAT is why we are such believers in maintaining a polite, respectful thread. Most everyone here is eager to help, and the only thing we ask is (despite the associated tedium) read the entire thread, it can only help. If and when you are still stuck, feel free to ask questions, we're all here to help one another.
--TMobTim
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
XDA:DevDB Information
|KERNEL| JediKernel | 1.0 | Lollipop | 01-07-2015 |, Kernel for the Google Nexus 5
Contributors
ptmr3
Kernel Special Features:
Version Information
Status: Stable
Created 2015-01-07
Last Updated 2015-01-07
Benchmarks are fun lol ------------ 2.88 clock -- OnDemand Gov -- ROW sched
LOVE NEW THING
"More...". Best feature ever.
ast00 said:
"More...". Best feature ever.
Click to expand...
Click to collapse
agreed. its a super-feature
I remember when you were building for the s2 haha. This guy has some amazing kernels!
Sent from my Nexus 5 using Tapatalk
I was thinking..
FauxSound is a "more" feature or not for now?
krazeecracker said:
I remember when you were building for the s2 haha. This guy has some amazing kernels!
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
Thanks man that was long ago lol
Robert- said:
I was thinking..
FauxSound is a "more" feature or not for now?
Click to expand...
Click to collapse
No sir,
More.. is usually in all of my feature lists because I always seem to forget something
Does it feature color control to change values in gamma and rgb settings?
First, thanks for sharing the kernel, i like it to play with different kernel.
One question,
Gamma Control a planned feature in the future ?
bunnahabhain said:
Does it feature color control to change values in gamma and rgb settings?
Click to expand...
Click to collapse
No. this is a v1 so many of what will be added is not currently there.
Also, the goal of this kernel is to stay as close to stock as possible while enhancing the performance, battery-life, and usability of the device.
Color and sound may or may not be included in future iterations
In download [emoji3]
Favorite Note 2 kernel was Jedi. Nice to see its way to Hammerhead!
Sent from my Nexus 5 using XDA Free mobile app
Do core (two or three) in offline?
Ok will try it now
Edit: kernel runs... Looking for good settings. Using ondemand and deadline for now.
One thing I miss.... A sound mod... Sound is to low... And the quality is not the best... Are there alternatives?
SunamY said:
Ok will try it now
Edit: kernel runs... Looking for good settings. Using ondemand and deadline for now.
One thing I miss.... A sound mod... Sound is to low... And the quality is not the best... Are there alternatives?
Click to expand...
Click to collapse
I'm pretty sure the dev wants us to use stock settings. Otherwise he wouldn't have made them default
For sound use viper mod. I don't see any kernel changes necessary for this.
Runs ok. Oc to 2.5. Uv would be nice
Slimlat 5.0.2
@ptmr3 glad to see u here man. This phone just keeps on getting better
krazeecracker said:
I remember when you were building for the s2 haha. This guy has some amazing kernels!
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
This. Glad to see him around here. Didn't think he would have a Nexus 5. Welcome to the Nexus 5, hope you're here to stay man.
Edit : Reporting that Jedi kernel does in fact run on 5.0.2 stable so far.
Some of you know me from the OOS3 kernel I built, and now I am moving to Nougat and starting working on it.
It mainly majors in keeping a balance between features and stabilities, so I did not add too many features (And I think features like adding 10+ governors is a bad practice), but the features I added is of great use. Some of the features are unique in existing OP2 kernels.
I am sick of those kernels which say it is the smoother than butter or is more powersaving than Nokia 1100, and I do not think that could happen. What I provide is an average kernel with some little tweaks. If you are looking for some specific features, this is not the place for you.
The features list:
Features:
- Catch up with latest Linux upstream 3.10.107
- Catch up with latest CAF source
- Catch up with latest sdcardfs, f2fs, exfat, xpad source
- Add flash and electron governor (both based on interactive, credits to The Flash and frap129)
- Tweaked interactive governor based on CAF MSM8996 branch
- CPU voltage control (The first for MSM8994?)
- Replace H-cube with core_ctl from CAF MSM8996 branch
- Remove powersave, conservative governor
- Add maple, sio, fiops, zen I/O scheduler
- Partly Faux sound control
- Partly thermal control
- KCAL
- Dynamic Sync control
- Wakeblock toggle
- Fingerprint boost tweaks
- Sultanxda's I/O switcher
- TheCrazyLex's memory automatic compaction mechanism
- Various improvements from AOSPA (thanks to TheCrazyLex)
- Various improvements from Sultanxda and myfluxi (The people I really admire)
- Various improvements from CAF
- Fix some ROM's ramdisk bug (why should I fix these?)
- ...
Usages:
Note that LineageOS based roms and other roms use different sysfs nodes for gestures. So I provide 3 versions, just use the one that your rom is based on, otherwise gestures may be broken. For non los based Roms, use other version, if it does not work (such as Pure Nexus), use pn version.
Use kernel adiutor to tweak it.
Source:
https://github.com/aviraxp/ONEPLUS_MSM8994_KAWORI
Credits:
Fist of all, thanks to Linux upstream and CAF. Without them, doing this work is impossible.
Of course, thanks to Lord Boeffla for a good picking source.
Then I want to thank to Sultanxda and myfluxi for the 30+ commits I picked and the guidance he provided. You are the real MVP!
I also want to say thanks to dorimanx, Joe Maples and Franco for the good features they provided.
Support:
Just like many other so-called "developers" for OP2, I do not major in computer science and know little about C. All my codes are written by guessing. Feel free to provide feedbacks, though I may not know how to fix it.
reserved
Nice to see new kernels popping up for the device. Good work @aviraxp
MZO said:
Nice to see new kernels popping up for the device. Good work @aviraxp
Click to expand...
Click to collapse
I am using your Purenexus
aviraxp said:
I am using your Purenexus
Click to expand...
Click to collapse
That's awesome ?
thanks for kernel. have you tested undervolting? is it safe? whats basic rules to use voltage control without killing phone? never used this feature
chxei said:
thanks for kernel. have you tested undervolting? is it safe? whats basic rules to use voltage control without killing phone? never used this feature
Click to expand...
Click to collapse
Phone should technically reboot and discard changes before any damage occurs
Sorry if I missed it.. Is this kernel compatible with official lineage weekly?
Sent from my ONEPLUS A3003 using Tapatalk
chxei said:
thanks for kernel. have you tested undervolting? is it safe? whats basic rules to use voltage control without killing phone? never used this feature
Click to expand...
Click to collapse
I have tested, and think undercoating about 80mV is fine. Lower voltage will make it reboot.
infatality said:
Sorry if I missed it.. Is this kernel compatible with official lineage weekly?
Click to expand...
Click to collapse
Of course
r2 will be soon uploaded , thanks to @MZO for pointing out a different implementation of gestures that I missed.
First of all: nice to see a new kernel of OP2, and I love new features! Good work!
Second: Unfortunatly, flashing this kernel for me kills WiFi on latest Unofficial RR. Had to flash stock boot.img to make it work again. Other than that it seems to work fine.
Defineatly gonna give it a try as my daily driver after WiFi issue is gone.
chxei said:
thanks for kernel. have you tested undervolting? is it safe? whats basic rules to use voltage control without killing phone? never used this feature
Click to expand...
Click to collapse
No problems for the hardware with undervolting but the system may become a bit unstable
almlex said:
First of all: nice to see a new kernel of OP2, and I love new features! Good work!
Second: Unfortunatly, flashing this kernel for me kills WiFi on latest Unofficial RR. Had to flash stock boot.img to make it work again. Other than that it seems to work fine.
Defineatly gonna give it a try as my daily driver after WiFi issue is gone.
Click to expand...
Click to collapse
I have tested my kernel on omni, du, aex and pn, no issues so far. Some lineage guys also flashed and encounter no issues. But I will try to look at it.
Using this kernel for Almost 12hrs, so far everthing working here with decent battery life.
Cpu cores implementation is the same as in Franco kernel (all cores always online) or different from it?
almlex said:
First of all: nice to see a new kernel of OP2, and I love new features! Good work!
Second: Unfortunatly, flashing this kernel for me kills WiFi on latest Unofficial RR. Had to flash stock boot.img to make it work again. Other than that it seems to work fine.
Defineatly gonna give it a try as my daily driver after WiFi issue is gone.
Click to expand...
Click to collapse
Could you please flash boeffla kernel and report if it works? I suspect it is a toolchain issue.
parasthakur37 said:
Cpu cores implementation is the same as in Franco kernel (all cores always online) or different from it?
Click to expand...
Click to collapse
Different. It is actually same as stock, just built in kernel to keep stability.
aviraxp said:
Different. It is actually same as stock, just built in kernel to keep stability.
Click to expand...
Click to collapse
And I suppose there's no way we can use franco's implementation if we wanted to?
parasthakur37 said:
And I suppose there's no way we can use franco's implementation if we wanted to?
Click to expand...
Click to collapse
I don't know what Franco's implementation is. I don't care either. If you want to keep all cores on, use kernel adiutor and change the min cpus to 4.
Hey there! Ayush Here!
INTRO
After a lot of hard work, I have a new custom kernel.
As the name suggest, these kernel is made as a All-Rounder, i.e it can provide better battery + performance . Without talking much lets go the features of these kernel.
MAIN FEATURES
Latest Linux Base 3.18.101
Overclocked CPU to 2.354 GHz (for Beast Performance).{Modified and Enhanced by me)
Support for more Governers { Impulse, Chill,relaxed, interactive modifed}
System wide PowerEfficent Workqueue (for Beast Battery Backup).
CPU input Boost.
Reduced CPU Load (for Beast Battery Backup).
Fixed High Load average (for Beast Battery Backup).
Fast idling of CPU (for Beast Battery Backup).
Less CPU-Load=Cool Device=More Battery-Life
Various Optimizations.
Add Lazyplug (Modified for Beast Battery Backup)
Overclock GPU to 652MHz(for Beast Performance)
Support for Adreno Boost
Enabled ARCH_Power (for Beast Battery Backup)
New PowerSuspend algorithm (for Beast Battery Backup)
Support for preventing unnecessary WakeLocks (for Beast Battery Backup)
Fast Charge Drivers.
Relaxed thermal threshlods for faster charging.
Support for mic, earpiece gain
Kcal Colour control v2
Uses custom colour profile by default for better screen vibrancy, colour reproduction.
Compiled with Clang
O3 Optimizations
Software CRC toggle
State Notifier support.
Various tweaks for better network speed
Support for Dynamic Fsync
Various Optimiztaions For Cpu and GPU
Various Tweaks for better battery+performance.
Fixed Deep sleep issues
Added LCD notifier
Added Quick Wakeup driver
Power Optimization.
These are the features which I remember, Many features are omitted due to word limit.
Check git for more.
I have tried my level best to make my kernel as best as possible. From minor tweaks to major improvements, everything is done.
Installation Instructions
Boot into recovery.
Wipe cache and dalvik cache
Flash Kernel
Reboot to system
Done
Downloads
R6
TREBLE :- https://www.androidfilehost.com/?fid=818070582850502954
NON-TREBLE
new trees :- (For roms which didnt got treble right now)
https://www.androidfilehost.com/?fid=890129502657593208
old trees :- (For roms by Mahek and some nougat roms)
https://www.androidfilehost.com/?fid=818070582850502955
Newtrees :- for roms based on tree of @dd3boh eg. Lineage OS, Cosmic, Aosip, PE, Aex etc.
Old Trees :- for roms based on tree of @Mr.hacker5476 eg Omni, validus, du
Click to expand...
Click to collapse
Kernel-Adiutor-Mod :- https://androidfilehost.com/?fid=818070582850490285
XDA:DevDB Information
*AR_Beast* Kernel, Kernel for the Lenovo ZUK Z2 (Plus)
Contributors
Ayush Rathore, faizauthar12, @dd3boh and all the commiters in source.
Source Code: https://github.com/AyushR1
Kernel Special Features: Fixed Deep Sleep, Faster Charging, OTG Fixed, Sound Control
Version Information
Status: Stable
Current Stable Version: 6
Stable Release Date: 2018-03-23
Created 2018-01-14
Last Updated 2020-04-20
Nougat or Oreo?
Reserved for review..
sanketp60 said:
Nougat or Oreo?
Click to expand...
Click to collapse
Only for oreo
I'm using it from its beta stages
Which build to download for validus latest?
Ans:- Old tree..
Check the post for The new trees section!
It dosent describe old trees
is deep sleep working？
Is it Working on stock oreo rom?
Thank god! The screen didnt flipped
Why no Ofast?) For Beast kernel size:laugh:
Also, Arch power is only harmful for modern SOCs. I recommend you disabling it and removing toddler for it.
Just flashed it with Cosmic OS
Pretty stable
Go for it!!!
Star_king12 said:
Why no Ofast?) For Beast kernel size:laugh:
Star_king12 said:
Why no Ofast?) For Beast kernel size:laugh:.
Click to expand...
Click to collapse
LOL. Post was copied will make corrections,
Star_king12 said:
Also, Arch power is only harmful for modern SOCs. I recommend you disabling it and removing toddler for it.
Click to expand...
Click to collapse
Ok. Will see thanks for suggestions.
Click to expand...
Click to collapse
Star_king12 said:
Why no Ofast?) For Beast kernel size:laugh:
Also, Arch power is only harmful for modern SOCs. I recommend you disabling it and removing toddler for it.
Click to expand...
Click to collapse
You have some serious mind issues.?
Star_king12 said:
Why no Ofast?) For Beast kernel size:laugh:
Also, Arch power is only harmful for modern SOCs. I recommend you disabling it and removing toddler for it.
Click to expand...
Click to collapse
Deleted
Ahh i remember that time i was fascinated with a lots of feature inside the kernel
Good job buddy :good:
Really great work mate i have a question regarding oc the little clusters can it be increased to 2.19 ghz like SD821 i know its more to ask just askin cuz the oc in your kernel feel snappy no issues so far
Ayush Rathore said:
LOL. Post was copied will make corrections,
Ok. Will see thanks for suggestions.
Click to expand...
Click to collapse
Also, you can make a unified version. Put fstab from dd3-s device tree in ramdisk folder of kernel zip and it will be booting on both device trees. (Worked for me, at least)
faizauthar12 said:
Ahh i remember that time i was fascinated with a lots of feature inside the kernel
Good job buddy :good:
Click to expand...
Click to collapse
Thanks buddy. Kernel based on your and @DD3Boh hardwork only.
Aka9413 said:
Really great work mate i have a question regarding oc the little clusters can it be increased to 2.19 ghz like SD821 i know its more to ask just askin cuz the oc in your kernel feel snappy no issues so far
Click to expand...
Click to collapse
Will be instable. Also i guess sd820 is powerful enough. No need of that.
Star_king12 said:
Also, you can make a unified version. Put fstab from dd3-s device tree in ramdisk folder of kernel zip and it will be booting on both device trees. (Worked for me, at least)
Click to expand...
Click to collapse
Thanks.
Damn how I forgot that:fingers-crossed:
Will do it. Thanks again
Awesome flashing it
Is the GPU OC being 652mhz added or it replacing 624mhz? because removing 624mhz would mess with AKT Profiles
---------- Post added at 11:02 PM ---------- Previous post was at 11:00 PM ----------
Ayush Rathore said:
Will be instable. Also i guess sd820 is powerful enough. No need of that.
Click to expand...
Click to collapse
I think SD820 is weak in terms of CPU power, as it only has 4 cores and in cpu heavy tasks like emulation it's really struggle. An overclock to at least match the sd821 would be great