[Help] Can't extract files from KDZ to debrick - LG Optimus G Pro

Hello guys, i got an LG G Pro Lite D681 that i failed to flash with LG Flash Tool 2014, and now the phone is dead and doesn't even vibrate or react if i press any key, BUT if i plug it in to the computer, the Device Manager recognizes it as MTK USB Port (COM3).
I don't think the device is completely dead, right? but i can't enter download mode so i can't use LG Flash Tool again.
1st: I have two firmwares:
LG_D681_V10A_00 and LG_D681_V20A_00
I've been trying to get the content of both in order to try to flash the images with SP Flash Tool v5.1524.00.000. The only tool that accepts the .kdz is LGExtract 0.2.1 by navossoc, all i get is:
LGD681AT-00-V20a-AMX-XXX-NOV-18-2014+0.bin
LGUP_MT6577.dll
Then i tried to extract LGD681AT-00-V20a-AMX-XXX-NOV-18-2014+0.bin with BinExtractor but i get this error:
Code:
Reading AP Header...
Failed Reading APHeader!
Reading GPT Header...
Does not contain GPT at first data block
Writing Files...
Finished
What am i doing wrong? What should i try to get the partitions and files needed to debrick? I've read a couple of tutorials but i can't do anything at this point
Thanks a lot in advance! :fingers-crossed:

Related

Prestigio 4500T Duo need to revive

I need help please, because I can't get my new prestigio 4500T turn on.
I first did the CWM recovery in this site, androidforum.cz/pro-pap4500t-dc-1-2ghz-s-jb-4-1-1-t38976.html
and it was all ok.
But then I wanted to remove the CWM recovery of my phone, because I had some problem updating my phone to the new rom because of it,
and I went to the same program I installed CWM recovery, Smart Phone Flash Tool, and I put the same scatter file I used to install, and instead of clicking on download I clicked Format, and then format whole flash, because it was there that I would take CWM recovery of my phone.
Now I can't turn my phone on, when I connect usb at pc, it connects and disconnects a lot of times. I even tried to do the same steps to download the CWM recovery on my phone but in SP Flash Tool I get this error: BROM ERROR: S_DL_GET_DRAM_SETTING_FAIL (5054)
[HINT]: Please check your load matches to your target which is to be downloaded.
I don't know what to do and please Help me. Thanks
Nobody answers? Please can anybody help me?
ddqgarces said:
I need help please, because I can't get my new prestigio 4500T turn on.
I first did the CWM recovery in this site, androidforum.cz/pro-pap4500t-dc-1-2ghz-s-jb-4-1-1-t38976.html
and it was all ok.
But then I wanted to remove the CWM recovery of my phone, because I had some problem updating my phone to the new rom because of it,
and I went to the same program I installed CWM recovery, Smart Phone Flash Tool, and I put the same scatter file I used to install, and instead of clicking on download I clicked Format, and then format whole flash, because it was there that I would take CWM recovery of my phone.
Now I can't turn my phone on, when I connect usb at pc, it connects and disconnects a lot of times. I even tried to do the same steps to download the CWM recovery on my phone but in SP Flash Tool I get this error: BROM ERROR: S_DL_GET_DRAM_SETTING_FAIL (5054)
[HINT]: Please check your load matches to your target which is to be downloaded.
I don't know what to do and please Help me. Thanks
Click to expand...
Click to collapse
You messed up boot file.Try to find original boot.img here on XDA and try to flash it via PC,or find original stock rom for flashing via SPFlashTool try that
jaskooo said:
You messed up boot file.Try to find original boot.img here on XDA and try to flash it via PC,or find original stock rom for flashing via SPFlashTool try that
Click to expand...
Click to collapse
Thanks for your help, I have a boot.img of the stock rom, I put in the same folder of MT6577_Android_scatter_emmc and CheckSum.ini , but when I try to download via SP flash tool I get this error:
Image Bootimg checksum failed! Checksum reference value (0x5583) in the config.ini file.
Please re-fill correct checksum values in checksum.ini.
I don't know what are the checksum values, can you tell me where i can find these values?
I am getting this DRAM error, because I don't have the correct files to flash in SP flash tool.
Please can you give me all those files needed to put a whole new firmware in y phone, I need the preloader file, and etc.
My phone can't detect preloader, as it did, and I can't boot it, it's like dead, only appears a red light when I connect to pc and a MTk USB Port (COM).
Please help me with the files needed to flash my whole phone in sp flash tool
Need full ROM with scatter file
Hi Guys, I am looking for full ROM including scatter file for PAP4500T. I need it to load all needed (Preloader, MBR, EBR1, UBOOT, BOOTIMG, RECOVERY, SEC_RO, LOGO, EBR2, ANDROID, CACHE, USRDATA) in to the SP Flash Tool. It can be from Stock or any working ROM. If You could provide me Working ROM with all these and with scatter file which will load everithink to the SPflashTool I would really appreciate that.
Thank You in advance.

LG G3 Brick, i try all

Hello I read all threads with brick text, i try all and i cant to unbrick my phone.
I try to update my lg g3 but i block the bootloader or something, then i enter in fasboot and i delete recover and follow this tutorial
http://forum.xda-developers.com/android/general/unbrick-lg-model-download-recovery-t3060184
With this i sure make a mistake, i upload all from 30b version, and in the tutorial dont say i need to flash custom1 and custom2, so i didnt... then i get out from fastboot and now i enter in download mode. I use flash tool 2014 and flash tool for tot files, with 2014 not work, with tot file it starts (i try with 10a and 10e version) but try to delete custom partition and fails in 6% says this
[17: 7:55] Can not find Parition name : cust
and not work any more.
I think the problem is that is expected 30b with custom partition and is not there, so it not continue. Any ideas what can i do?
Orko2002, can you enter to download mode ?
UvarovG said:
Orko2002, can you enter to download mode ?
Click to expand...
Click to collapse
Yes is the only mode i cant enter, download mode (pressing vol +) and got to upload firmware screen. I connect to flash tool and up to 6% and crash.
I try factory reset (power + vol -) it says ok but nothing happends... now if i power normal, lg logo starts, says boot verification fails, and the screen goes black.
>I connect to flash tool and up to 6% and crash.
What happens if try to restore stock rom via "LG Mobile Support Tool" ?
UvarovG said:
>I connect to flash tool and up to 6% and crash.
What happens if try to restore stock rom via "LG Mobile Support Tool" ?
Click to expand...
Click to collapse
Thanks for reply!
When i open lg mobile support tool and connect the cel on download mode, the LGST doesn´t detect the mobile....
I go to admnistrative tools and see the cel on COM41 but the tool doesnt detect it. Can i do something to detect?
Anyone knows where download 30c or 30b tot file? i cant find it, to try with a new tot
[deleted]

how to unbrick LG Optimus G Pro E98820c qualcomm hs-usb qdloader 9008 mode

I appreciate all of your kind helps.
I am having the BRICK problem with LG G Pro e98820c after flashing wrong rom and unplug USB during flashing process.
Now the phone is stuck at Brick qualcomm hs-usb qdloader 9008 mode. I have some tools such as Smart diagnosis tool, BoardDiag, Androidbrick, Qfil/QPST ....But I have no proper guide how to use them to unbrick qualcomm hs-usb qdloader 9008 mode.
Have you got a solution for your brick phone.
I got LG optimus G Pro e98820c bricked during flashing a kdz update. I tried to upgrade a lollipop 5.0.2 rom of korean variant F240L model. The phone has long released and used.
This is how things went wrong:
I flashed the rom, but stuck at download with no booting, then unplugged USB, then and there it went bricked.
No battery light
No download mode......Now it is totally DEAD
Luckily, when it is plugged on Windows 8, the device manager shows Qualcomm HS-USB QDloader 9008(COM15). Is this sign of the phone going back to life? How should I step forward to get back Download Mode?
I tried to test and unbrick it on BoardDiag, but it shows ...
#[ G-pro (APQ8064)]
============= AP CHECK START
Failed during loading flash programmer
TEST aborted!!
Elapsed Time: 0 hours 0 minutes 0 seconds#
This is the message I got from BroadDiag. but since there is no .TOT firmware for G Pro e988C, I think I can not do image extraction from .KDZ firmware. Is that right way to do image extraction from .KDZ firmware zip? I have a problem with no partition .txt file available from extraction of KDZ zip. How can i get partition .txt ?
There are KDZextractor, Can I use them? Can these image extracted from KDZ be applied in BoardDiag?
All of your answers is highly appreciated.
Sho Thant
Mandalay, Myanmar . Tech Savvy.
TOT is only for E980 AT&T variant. E988 uses KDZ. Try with BordDiag then, but I'm not sure it will work. There are some guides here in G Pro forums, but never had to use them because mine never bricked that bad. If nothing works, JTAG/repair.
ShadySquirrel said:
TOT is only for E980 AT&T variant. E988 uses KDZ. Try with BordDiag then, but I'm not sure it will work. There are some guides here in G Pro forums, but never had to use them because mine never bricked that bad. If nothing works, JTAG/repair.
Click to expand...
Click to collapse
Dear Shady Squirrel,
I have tried BoardDiag, but it keeps giving the following message:
#[ G-pro (APQ8064)]
============= AP CHECK START
Failed during loading flash programmer
TEST aborted!!
Elapsed Time: 0 hours 0 minutes 0 seconds#
I am stuck at this stage. But maybe I have no proper way of using BoardDiag.
In the instruction from the forum, the extracted files needed are ( .mbn ) file not ( .bin ) file which are extracted from KDZ.
Can you help me instruct for BoardDiag tool?
Thank a lot in advance.
Sho Thant
Sho Thant said:
Dear Shady Squirrel,
I have tried BoardDiag, but it keeps giving the following message:
#[ G-pro (APQ8064)]
============= AP CHECK START
Failed during loading flash programmer
TEST aborted!!
Elapsed Time: 0 hours 0 minutes 0 seconds#
I am stuck at this stage. But maybe I have no proper way of using BoardDiag.
In the instruction from the forum, the extracted files needed are ( .mbn ) file not ( .bin ) file which are extracted from KDZ.
Can you help me instruct for BoardDiag tool?
Thank a lot in advance.
Sho Thant
Click to expand...
Click to collapse
Never used it - my worst brick was solved by putting device in download mode and doing a full stock reflash. Haven't managed to mess-up bootloader for 3ys I've used G Pro. Try running app as admin, KDZ should work, it's valid image - people are just referencing to tot files because they are all copy/pasting same tutorial around the webs.
In the end, it would be much smarter to just send it to service...
ShadySquirrel said:
Never used it - my worst brick was solved by putting device in download mode and doing a full stock reflash. Haven't managed to mess-up bootloader for 3ys I've used G Pro. Try running app as admin, KDZ should work, it's valid image - people are just referencing to tot files because they are all copy/pasting same tutorial around the webs.
In the end, it would be much smarter to just send it to service...
Click to expand...
Click to collapse
Thanks for your kind advice, anyway I will give it a one last try with the extracted images from KDZ on BoardDiag.
If it does not turn up good, better send it to service center.
Sho Thant

Flash failed, stuck in download mode (H815)

Hi guys,
for the last months I was using LineageOs, but since they dropped development for our device I wanted to get rid of it.
I tried to get AOSP running but failed. Next I flashed a stock kdz file in Download Mode using LGUP and it worked,
I was back to stock. I tried to install AOSP through TWRP but failed again and eventually ended up doing a hard reset.
This temporarily bricked the device because now the stock android booted and Android Device Protection (FRP) was
active and didn't let me log in. Desperate to find a solution I flashed random kdz/tot files for the device that I found on
the Internet until one finally worked (LGH815 EU Nougat 7.0 BySezerSimsek), the FRP thing was gone. Then I tried to at
least get back to stock again, but when I tried to flash the stock kdz file LGUP aborts at 25% with Error Code 0x2000.
Every time I start the phone now, it goes directly in this firmware update/download mode.
The device shows up as "LGE AndroidNet USB Serial Port" In Windows Device Manager
In Download mode it says "633A B92 Official" on the display
I already tried:
Different dll files for LGUP
Using LG Flash Tool 2014 instead
Putting dump file on SD card
Should I put it in 9008 mode and work with QFIL or what am I supposed to do now?
Thank you.
I'm still able to get into fastboot mode btw. But I'm going to wait for replies here
before I make things worse. If that's even possible at this point. :silly:
h4yabu5a said:
I'm still able to get into fastboot mode btw. But I'm going to wait for replies here
before I make things worse. If that's even possible at this point. :silly:
Click to expand...
Click to collapse
:highfive:<-
jason_l367 said:
:highfive:<-
Click to expand...
Click to collapse
My phone is alive again, thanks Jason:laugh:
Just a short recap what I've done now in case it helps someone with the same problem, the full instructions
are in Jasons link.
I used the KDZ and TOT Extractor to extract the LGUP8994.dll file out of a stock Marshmallow v20p KDZ.
I renamed the dll to LGUP_8994.dll and moved it to C:\..\LG Electronics\LGUP\model\8994, overriding the
existing file. Now LGUP was able to flash the v20p KDZ without the 0x2000 Error.

unbrick Nokia 3.2

Hello together,
after many tries to get my nokia 3.2 rooted, i end up now with a black screen.
Only the Qulacomm mode is working.
Get anyone managed to flash the stock firmware with QFIL provided from the rooting thread?
I always end up with "sahara fails".
Every help is welcome!
Thanks!!!!
After many tries I have finally put my phone back to life.
My instructions how to do it will come soon!
page1875 said:
After many tries I have finally put my phone back to life.
My instructions how to do it will come soon!
Click to expand...
Click to collapse
please do, i encountered a similar problem.
HowTo Flash STOCK 00WW
1. Trigger nokia 3.2 to edl-mode (https://forum.xda-developers.com/nokia-3-2/how-to/guide-how-to-trigger-nokia-3-2-to-edl-t3962841)
2. Flash the given image from this thread (https://forum.xda-developers.com/nokia-3-2/how-to/rooted-nokia-3-2-t3945206)
- This was the main problem. I never managed it to flash the image with the Windows Programmer QFIL. After more research in Internet, i found finally a Linux application called QDL that work directly without any problems. This application can be found here https://www.96boards.org/documentation/consumer/guides/qdl.md.html .
- Flashing the software ends up into a bootloop. Also i got a message on startup that the bootloader could not be trusted anymore. After a software-update, this message disappears.
3. Flash all the user images again manually with fastboot.
fastboot flash boot boot.img
fastboot flash dtbo dtbo.img
fastboot flash system system.img
fastboot flash vendor vendor.img
flastboot flash vbmeta vbmeta.img
Whyever you have to flash this partitions only to the active partitions without the suffix _a or _b.
Then the bootloop is finished.
The phone boots normally to Android ONE.
The next problem which occurs on my phone is now that it is not able to connect to GSM network. I guess this happens because i deleted all the necessary partitions for the modem (modemst1, modemst2, fsg).
I get it managed to restore the imei, but still no service available.
In original my phone had the software 00EEA. Perhaps they use different drivers. My luck is that i got a cheap damaged phone from ebay with that firmware.
My next step is to modify the code from QDL that it can read the partitions from the damaged phone and save the software to computer.
Then i will flash this software to my phone and look if this software will run on my phone!
page1875 said:
1. Trigger nokia 3.2 to edl-mode (https://forum.xda-developers.com/nokia-3-2/how-to/guide-how-to-trigger-nokia-3-2-to-edl-t3962841)
2. Flash the given image from this thread (https://forum.xda-developers.com/nokia-3-2/how-to/rooted-nokia-3-2-t3945206)
- This was the main problem. I never managed it to flash the image with the Windows Programmer QFIL. After more research in Internet, i found finally a Linux application called QDL that work directly without any problems. This application can be found here https://www.96boards.org/documentation/consumer/guides/qdl.md.html .
- Flashing the software ends up into a bootloop. Also i got a message on startup that the bootloader could not be trusted anymore. After a software-update, this message disappears.
3. Flash all the user images again manually with fastboot.
fastboot flash boot boot.img
fastboot flash dtbo dtbo.img
fastboot flash system system.img
fastboot flash vendor vendor.img
flastboot flash vbmeta vbmeta.img
Whyever you have to flash this partitions only to the active partitions without the suffix _a or _b.
Then the bootloop is finished.
The phone boots normally to Android ONE.
The next problem which occurs on my phone is now that it is not able to connect to GSM network. I guess this happens because i deleted all the necessary partitions for the modem (modemst1, modemst2, fsg).
I get it managed to restore the imei, but still no service available.
In original my phone had the software 00EEA. Perhaps they use different drivers. My luck is that i got a cheap damaged phone from ebay with that firmware.
My next step is to modify the code from QDL that it can read the partitions from the damaged phone and save the software to computer.
Then i will flash this software to my phone and look if this software will run on my phone!
Click to expand...
Click to collapse
Thank you for your reply, it seems that your problem is more complicated than mine.
I have a global variant with 00WW software and i attempt to root the phone. I successfully flash the patched boot.img and had root access. However wi-fi didn't work after that.
Since before flashing the patched boot.img my phone was running on a different firmware from the one that boot.img was extracted from, so i think that was the problem.
I attempted to use QFIL to flash my phone back to 00WW_15 and it failed half way, bricked my phone.
Normally you can use the EDL Mode every time.
My phone only showed black screen and it was always possible to connect in EDL Mode and flash again.
Did you try to flash again? What happens then?
Flash the given image from this thread (https://forum.xda-developers.com/nokia-3-2/how-to/rooted-nokia-3-2-t3945206)
Click to expand...
Click to collapse
What did you mean by Flash the given image ? Was it flash the firmware package with QFIL ?
My main problem is flashing, it always failed half-way and the error log reported that needed files were missing from the package.
Okay. I used the linux program QDL for flashing.
But i saw, that in the xml file rawprogram0.xml a few files are missing.
The linux programm jump over these files but perhaps QFIL do not.
For example is there a picture.img listed which is not available..
Try to remove them manually from the rawfile and test again.
page1875 said:
Okay. I used the linux program QDL for flashing.
But i saw, that in the xml file rawprogram0.xml a few files are missing.
The linux programm jump over these files but perhaps QFIL do not.
For example is there a picture.img listed which is not available..
Try to remove them manually from the rawfile and test again.
Click to expand...
Click to collapse
@update:
Also the files "demoapp.img", "dp_AP_signed.mbn" and "dp_MSA_signed.mbn" are missing.
Remove them from the XML file and try again!
@update
Okay QFIL still failed half-way but i manually flash the user images and my phone boots normally now
Hello,
my nokia 3.2 europe variant wont boot up its stuck in fastboot mode. What can i do to bring it back?
I get this: FAILED (remote: partition table doesn't exist)
P.S. if i do a fastboot reboot it boots back into bootloader
I also had this problems for many many times and don't know what went wrong when this happens.
The only thing that helped was flashing the complete firmware again in EDL-mode.
You can try first to flash only the 5 user-images with fastboot, which i mentioned before in this thread.
I uploaded this files for you, because you don't will find the europe files in internet yet.
Here is the link:
https://transfernow.net/81iti7q21s0s
Good luck!
Hi,
Thank you very much. Is this the complete Firmware? (All Images from Device) Another question: I couldnt Access the recovery System. Did you have the same Problem when your Nokia didnt boot up and was stuck in Bootloader? So is this normal that the recovery is unaccessible?
Yes, that also happens sometimes with my phone.
No, that are not all firmware files, which you need to do a full EDL-Flash.
But with this files you can first try a fastboot flash!
If it does not work, you can take all the other files from the Global-Stock-Firmware, given in the thread https://forum.xda-developers.com/nokia-3-2/how-to/rooted-nokia-3-2-t3945206.
Delete the 5 files with the same names, flash the Global-Stock-Firmware in EDL-Mode, with QFIL or QDL, (without the 5 files) and in the following flash the 5 europe-image files with fastboot.
Thanks, ive sent it in and got Friday a 00WW Variant of the device back. I will upload those User images for 00EEA to my Google drive so that anyone who needs those files can download them
hello
i wanted to install custom rom and i bricked my phone. i lost recovery mode and i have only fastboot mode .but can not write any img file for example twrp.img beacuse show this error : FAILED (remote: partition table doesn't exist). can please anyone help me.
thank you very much
thanks so much i was able to put my phone back to life. i had almost given up.
smure said:
thanks so much i was able to put my phone back to life. i had almost given up.
Click to expand...
Click to collapse
Hello to ervery one
how you flashed your phone. can you please guide?
i am also stucked in fastboot mode after rooting.
damn... I've been finding on how to restore the wifi and sound because I uninstalled magisk and it failed. I don't think I can thank you enough for this post.

Categories

Resources