Develop Bugs

[Q] Samsung Wave 2 semibrick ?

Hi,
Since I tried to flash my Wave 2 (I didn't suceed, because the phone turned off before the end), my phone won't boot. Nothing displays when I just try to boot it, and when I plug it to computer, it displays a warning sign between a phone and a computer (I joined a pic of it), but the phone reboot approx every 20 sec displaying again this sign.
When it's pluged to computer and I press vol down, lock and deny call buttons, download mode appear for a few (1 or 2) sec then it reboot displaying the sign...
What could I do ? I think it might be a battery problem but it don't seems to load in this mode.
Thx in advance,
Bye.

Press Volup+Camera+Power button u should be able to get Download Mode
Then Flash again via Multiloader

Well, thank you for your answer, but I'm not able to go to download mode, because my phone just reboot half a sec after download mode displays.
What could I do ?

because my phone just reboot half a sec after download mode displays.
Click to expand...
Click to collapse
Battery damaged or empty...
Check battery.
Hint. In Download Mode you can NOT charge battery...
So check in other device or use other battery...
Good luck.
Best Regards

Hi,
Thanks for your help.
I finally managed charging my battery, and I tried to flash TurkoCFW, but it never works, I either get a "Error : FFS Write" or a "Error : CSC Write".
What could I do ?
Thanks in advance.

[Q] Arc s with no os and battery dead not booting

Hi guys, I'm here because I'm deseperate. My arc s won't boot if i press the power button or if I connect it to pc . It has no os because i format the system folder while I was trying to flash a rom, and the battery is surely dead. I cannot enter neither in fastboot nor in flashmode. Is there any way to charge the phone so that I can flash any firmware? Or should I buy another battery?

SilverSurfer(MrAllIn) said:
Hi guys, I'm here because I'm deseperate. My arc s won't boot if i press the power button or if I connect it to pc . It has no os because i format the system folder while I was trying to flash a rom, and the battery is surely dead. I cannot enter neither in fastboot nor in flashmode. Is there any way to charge the phone so that I can flash any firmware? Or should I buy another battery?
Click to expand...
Click to collapse
Keep it in charge even if the phone does not show anything, it will charge.
i had the same issue with Ray i erased the kernel and battery died i kept it in charge for 10min and it started in fastboot mode

ManthanRB said:
Keep it in charge even if the phone does not show anything, it will charge.
i had the same issue with Ray i erased the kernel and battery died i kept it in charge for 10min and it started in fastboot mode
Click to expand...
Click to collapse
Thanks for the reply, but I don't think it works., because i've plugged it for at least one day and still can't enter in recovery or do anything :crying: any tips?

SilverSurfer(MrAllIn) said:
Hi guys, I'm here because I'm deseperate. My arc s won't boot if i press the power button or if I connect it to pc . It has no os because i format the system folder while I was trying to flash a rom, and the battery is surely dead. I cannot enter neither in fastboot nor in flashmode. Is there any way to charge the phone so that I can flash any firmware? Or should I buy another battery?
Click to expand...
Click to collapse
It will go in Fast boot mode Just press Menu key(on my neo v its on right side of home button) and see if blue led turn on in your arc.
if your device still not entering on fastboot mode and you want to charge your mobile battery then find any compatible universal charger for your device

I guess by saying "universal charger" what fenix meant was a spare battery charger which, charges batteries while unattached from the phone itself... or he/she probably was referring to something else.
anyway, the spare battery charger that I know looks like this:
http://www.ebay.com.au/itm/BA750-Ba...Arc-XPERIA-Arc-LT15i-Xperia-X12-/170822357636
or you can just search through google for it using the keywords "spare battery charger LT15i anzu".
good luck!

P8000 won't boot

Hi all, i have problem with my P8000. My phone was discharged to 0%, and then i cant turn on phone. When i plug it to charger, blue circle do not light. i try to do:
1. Hold POWER - phone starts but when display elephone logo (1 second) telefon turn off
2. Hold POWER and POWER + - phone gone to bootloader, and them whatever i choose (recovery, normal) phone starts but after shown elephone logo turns down (like 1.)
3. Flashed stock rom via Flash tool (format + download) - like 1.
4. I have unpluged battery
after all, phone cant start... Someone can help me?

I think you have to leave it charging for a while before you are able to turn it on again. Just give it some time

jman0 said:
I think you have to leave it charging for a while before you are able to turn it on again. Just give it some time
Click to expand...
Click to collapse
I charged it for 48h and i cant turn it on...

mczlowiek said:
I charged it for 48h and i cant turn it on...
Click to expand...
Click to collapse
Try another charger/usb cable, just in case the one you're using is defective, or charge the phone connected to a computer

jman0 said:
Try another charger/usb cable, just in case the one you're using is defective, or charge the phone connected to a computer
Click to expand...
Click to collapse
another charger/usb cable did not solve my problem. When i plug phone into computer, then computer recognize it. I flashed stock rom with flastool, but problem was the same.... I changed battery (buy new one) but problem is this same...

blimps
mczlowiek said:
another charger/usb cable did not solve my problem. When i plug phone into computer, then computer recognize it. I flashed stock rom with flastool, but problem was the same.... I changed battery (buy new one) but problem is this same...
Click to expand...
Click to collapse
Hi,
I have/had the same problem. The problems started, with the phone powering down, at half the battery level. Then I got a spanish battery overheating message. After the message appears, the problem starts.
I solved the problem like this :
First you have to completely drain your battery. How to do that ?
- Go to the boot-menu (press power on button, and volume up at the same time). Select : Fastboot. The phone will halt. BUT, keep your phone in that state, so it consumes energy. After a while your phone will go out. After that : go again to your boot menu, but DON'T select any options. After a period of ± 5 minutes your phone will go out.
- THEN : remove your SD-Card, and SIM-Card.
- THEN : Connect your phone with the net-usb-charger. DON'T connect it to your PC.
- After 1 to 2 hours of chargeing, your down center button, should start glowing blue again.
I got my phone working again 2 times using this method.
I hope it works for you.

Phone Restored with this method! Thanks pal!

worked for my phone
thank you very much

LG G3 Stuck in Factory Reset Status 2

Hello there,
Today my rom (Xenon HD) stopped working and i wanted to get my old stock rom back.
So i started to downgrade, but in the end i ended up in the Factory Reset Status 2 after it shows the boot animation of an os called "mini os".
Anybody got experience on this ?
Thanks
Baschdi

Factory Reset 2
Baschdi_ said:
Hello there,
Today my rom (Xenon HD) stopped working and i wanted to get my old stock rom back.
So i started to downgrade, but in the end i ended up in the Factory Reset Status 2 after it shows the boot animation of an os called "mini os".
Anybody got experience on this ?
Thanks
Baschdi
Click to expand...
Click to collapse
First remove your battery then insert battery dont power on mobile . holding the volume up, plug in a microUSB cable into your phone.
Make sure the USB side is already plugged into the computer
You should start to see "Download Mode" for a few seconds and then it will show "Firmware Update". You are now in Download Mode!
Open LG Flash Tool and Put your dll and tot files in and use Board DL (Very Important)
after u success
It should boot into MiniOS just hit ok. Push power button plus touch the screen where it says Normal boot+(power)
done

This is not working for me. it says waiting for connection, please help
i am frustrated !!!

likhil2k3 said:
This is not working for me. it says waiting for connection, please help
i am frustrated !!!
Click to expand...
Click to collapse
Try unplugging and plugging back in and ensure you are on PORT41 for the device driver. After you do that and in Download Mode, then unplug and replug USB.
Also do not use USB 3 and try another port if you still have issues.

Bhimani bhargav said:
First remove your battery then insert battery dont power on mobile . holding the volume up, plug in a microUSB cable into your phone.
Make sure the USB side is already plugged into the computer
You should start to see "Download Mode" for a few seconds and then it will show "Firmware Update". You are now in Download Mode!
Open LG Flash Tool and Put your dll and tot files in and use Board DL (Very Important)
after u success
It should boot into MiniOS just hit ok. Push power button plus touch the screen where it says Normal boot+(power)
done
Click to expand...
Click to collapse
I have same issue in my LG G3 D850 I have apply your procedure Thanks It works ... first time the setup screen completes but when i powered off mobile and insert the sim and then powered on its again going to miniOs again i Normal boot+(power) but now boot looping auto ... what can i do now ???

For me who had the same issue, I just rebooted the device back into download mode and the LG flashtool resumed automatically. (I did not close or stop the process from the LG flashtool when I got this message).
Once the process resumed automatically, I still got download fail.
I can see whenever the device reboots, the modem disappears from within device manager after getting to the "Factory Reset 2" screen.
Any advice?
Update: I tried about 7 times to get it flashed. I ended up just restarting the phone in normal mode and strangely voila it works perfectly. Even though the software said the flash failed, it still worked. Thanks anyway!

Bhimani bhargav said:
First remove your battery then insert battery dont power on mobile . holding the volume up, plug in a microUSB cable into your phone.
Make sure the USB side is already plugged into the computer
You should start to see "Download Mode" for a few seconds and then it will show "Firmware Update". You are now in Download Mode!
Open LG Flash Tool and Put your dll and tot files in and use Board DL (Very Important)
after u success
It should boot into MiniOS just hit ok. Push power button plus touch the screen where it says Normal boot+(power)
done
Click to expand...
Click to collapse
This worked. Tks a lot.

I just got a LG harmony and as i soon turned it on it went to factory reset status and I tried to bypass but it keeps taking me to Factory reset, I also tried the download mode which took me to firmware update for hours it has still been at 0%. Taking forever

Bhimani bhargav said:
Factory Reset 2
First remove your battery then insert battery dont power on mobile . holding the volume up, plug in a microUSB cable into your phone.
Make sure the USB side is already plugged into the computer
You should start to see "Download Mode" for a few seconds and then it will show "Firmware Update". You are now in Download Mode!
Open LG Flash Tool and Put your dll and tot files in and use Board DL (Very Important)
after u success
It should boot into MiniOS just hit ok. Push power button plus touch the screen where it says Normal boot+(power)
done
Click to expand...
Click to collapse
thank you very much ,it work succesful

[GUIDE] QDLoader 9008 fix | EDL Mode fix

Hi everyone,
If your phone does not react on any of yours actions. You may have the same problem. This is an instruction how to fix it.
If you have a last version of Windows 10 you can easily check if it is your case (You will have "Qualcomm HS-USB QDLoader 9008" device at your Windows devices' list.
How to Fix:
1. Download Drivers Qualcomm_QDLoader_HS-USB_Driver_64bit_Setup.zip and install it.
2. Download firmware link1 or link2
3. Install the driver
4. Unpack a firmware archive
5. Power off your phone by pressing Voice Down + Power Buttons (If your phone would be in this state too long the script would not works).
6. Start update_image_EDL.bat script - it will recreate all of the partitions
7. After the script will finish you will see the bootloader
8. Start script flashall_AFT.cmd - it will install firmware to the new partitions
9. Download fresh official firmware from asus site and put the archive at your memory card.
10. Start bootloader
11. Go to a standard recovery mode and install this firmware form the card
12. restart and repeat 10-11 (it will install software at the second state)
13. The problem is fixed. Congratulations!
Common problems:
Exception: System.DLLNotFoundException: DLL "QMSL_MSVC10R.dll": Module was not found. (HRESULT: 0x8007007E) can not be loaded.
Solution: You need to install Microsoft Visual C++ 2010 Service Pack 1 Redistributable Package MFC. Thanks to Genim

can you please update the post with the links to the software? thanks

admirdante said:
can you please update the post with the links to the software? thanks
Click to expand...
Click to collapse
I tried, but this was my first message, so I could not manage to do it (I need at least 10 messages). However, I report it to a moderator teams. I hope they will do it for me.

Hi OP,
I have edited the links into first post for you. Enjoy.
Jerry
Forum Moderator

Thank you so much OP. You saved my phone. It's been in Edl mode for about 2 months. Now it's up and running again.
Guys if I can add one thing to the OP post .. Make sure you plug the phone in and let it charge for awhile before attempting. Once you get to the fastboot mode it will not allow you to continue if your battery is too low. I understand that you can't tell what percentage the battery is but just let it charge for 2 hours and then do the whole process. I had to stop when I got to the fastboot stuff. And then continue after 2 hours on the charge.

st3wart said:
Thank you so much OP..
Click to expand...
Click to collapse
You are welcome. It took some time, so I decided to publish it.
st3wart said:
I understand that you can't tell what percentage the battery is but just let it charge for 2 hours and then do the whole process.
Click to expand...
Click to collapse
In fact I can. I intentionally bricked my phone 3 times to write the simplest possible tutorial (my first solution was too long, because I could not understand why the problem was fixed).
I could not implement this solution when I had 6 per cent of battery, but it worked ok when I had 11 per cent. I can guess, that if it more than 10% - it is ok to implement this tutorial.

st3wart said:
Thank you so much OP. You saved my phone.
Click to expand...
Click to collapse
I'm glad it worked for you! I made it into FastBoot Mode, but when I select Recovery, it puts me back into FastBootMode.
Am I missing something or did something not work properly? Don't know how to flash the official firmware now.

In fastboot mode... Go to the extracted files and double click on the flashall_aft file and sit back and wait until it finishes.

st3wart said:
In fastboot mode... Go to the extracted files and double click on the flashall_aft file and sit back and wait until it finishes.
Click to expand...
Click to collapse
I did click it. It opened and closed cmd too fast for me to read though.

That's what it did when my battery was low... Go plug your phone in with the original charger for an hour and then go directly to your PC and plug it in and double click that file and it should do it's job.
Also check to make sure your antivirus isn't blocking the file. Mine blocked access to it for whatever reason.

I did click it. It opened and closed cmd too fast for me to read though.
Click to expand...
Click to collapse
It looks like st3wart's answer is correct. I faced the same behavior when my phone had 6 per cent of battery. This problem was fixed as soon as my phone had 11 per cent of the battery. Thus you should try to charge it before starting the script.
Furthermore, if you would still face this problem you can copy files fastboot_.log and test1.txt and share all of logs with us (or just find the error by yourself).

error from fastboot_.log:
"Writing 'partition:0'...
FAILED (remote: Warning: battery's capacity is very low)"
I did charge it for 2+ hrs with the original charger though. When I unplug it, turn it off and back on again it gives a low battery error. When I plug it back in, it goes straight back into FastBootMode.
But it seems to not charge the battery for some reason.

I did charge it for 2+ hrs with the original charger though.
Click to expand...
Click to collapse
Did you charge it in EDL mode?
For some reasons it did not work for me either. I just booted to bootloader, then power-off the phone and saw the animation of charging. You can also try to flash TWRP (using their instructions) and charge your phone in this mode.
If it does not work - please check your charger.

goldman1993 said:
Did you charge it in EDL mode?
Click to expand...
Click to collapse
As soon as I charge the phone, the FastBoot screen comes up. When I select power off, it comes right back into FastBootMode. Is there a way to force shut down so i can charge it?
Also tried installing twrp, but when I select RecoveryMode it puts me back into FastBootMode again.

When I select power off, it comes right back into FastBootMode. Is there a way to force shut down so i can charge it?
Click to expand...
Click to collapse
It is a bit abnormal behavior. I'm not sure, why it happens, to be honest. Have you tried to use different cable or charger (I'm not sure what is the reason, so I would try to change something)?

Genim said:
As soon as I charge the phone, the FastBoot screen comes up. When I select power off, it comes right back into FastBootMode. Is there a way to force shut down so i can charge it?
Also tried installing twrp, but when I select RecoveryMode it puts me back into FastBootMode again.
Click to expand...
Click to collapse
Press power button for long time to power off.
Then try flashing every image of that link:
https://forum.xda-developers.com/ze...ne-6-proton-kernel-v1-0-t3963948/post80405617

goldman1993 said:
Have you tried to use different cable or charger?
Click to expand...
Click to collapse
I have.
I unplugged the phone and let the battery run comepletely empty until the phone shut off.
Then I plugged it back in and it charged for a minute (could see the charging symbol).
It then turned itself back on into FastBoot and stopped charging again.
---------- Post added at 07:29 PM ---------- Previous post was at 07:29 PM ----------
EMJI79 said:
try flashing every image of that link
Click to expand...
Click to collapse
I did flash them, but for some images it gave me the following error:
FAILED (remote: 'Error flashing partition : volume full')

Genim said:
I did flash them, but for some images it gave me the following error:
FAILED (remote: 'Error flashing partition : volume full')
Click to expand...
Click to collapse
Not good...

Then I plugged it back in and it charged for a minute (could see the charging symbol).
It then turned itself back on into FastBoot and stopped charging again.
Click to expand...
Click to collapse
Well, we can try to brick it one more time (put it into EDL mode). Then you can try to power it up in this state and unbrick it one more time.
Firstly you need to load to bootloader and write
.\fastboot.exe --set-active=b
Then you need to reboot your phone.
I believe, that you would not successfully load to bootloader (IT would be the same EDL mode), so you can try to charge it in this state or try tutorial one more time. (After a 30 minutes of your charging process you can try tutorial one more time).

goldman1993 said:
.\fastboot.exe --set-active=b
Click to expand...
Click to collapse
I ran that command and it bricked the phone again.
But I did wait too long before running the script. I'm getting an Sahara error.
How should I proceed? Can I just run that line again?