Related
Hi, i played around with my new OP3, and i wanted to root it. Since i'm noob at rooting, it went wrong. (i did it with twrp)
So first it just went in to bootloop, then i was still able to get to rcovery and stuff, but i followed a guide to fix bootloop, and that ****ed it even more up. The guide i followedet told me to use "OnePlus3_Unbrick_Tool"
After using "OnePlus3_Unbrick_Tool", i now cant even go into recovery anymore, the only thing i can do is go to bootloader, but when i'm in bootloader now, it wont connect proberly, so that i can use "flash twrp", so that i can use twrp recovery.
Also when i try to boot it, it because of "OnePlus3_Unbrick_Tool" goes into something, where it says "md5 checksum failed", and then restarts and does it again and again.....
I hope it's not bricked forever, pls help ))
have you tried re-flashing the stock or twrp recovery with adb sideload command?
if not give it a shot, it might work.
bonham1988 said:
have you tried re-flashing the stock or twrp recovery adb sideload command?
Click to expand...
Click to collapse
And how do you say I do that? I have tried using the "tool all in one", where you han flash both stock and twrp, but it doesnt seem to do anything, when i press them (and the device is in bootloader)
Godeske said:
And how do you say I do that? I have tried using the "tool all in one", where you han flash both stock and twrp, but it doesnt seem to do anything, when i press them (and the device is in bootloader)
Click to expand...
Click to collapse
Just boot into bootloader mode and through command prompt check if your phone is detected by typing fastboot devices. If its detected then you flash a new recovery again. Forget the toolkit, just look for instructions on how to install a custom recovery.
Sent from my OnePlus3 using XDA Labs
bonham1988 said:
Just boot into bootloader mode and through command prompt check if your phone is detected by typing fastboot devices. If its detected then you flash a new recovery again. Forget the toolkit, just look for instructions on how to install a custom recovery.
Sent from my OnePlus3 using XDA Labs
Click to expand...
Click to collapse
Okay i've tried that now, and it wont allow me unlock my bootloader from command prompt, and i cant do the flash while it's locked.. what to do?
Godeske said:
Okay i've tried that now, and it wont allow me unlock my bootloader from command prompt, and i cant do the flash while it's locked.. what to do?
Click to expand...
Click to collapse
In fastboot mode, did you manage to find your device on the computer? On Linux this is "sudo fastboot devices", on Windows it should be roughly similar.
simthadim said:
In fastboot mode, did you manage to find your device on the computer? On Linux this is "sudo fastboot devices", on Windows it should be roughly similar.
Click to expand...
Click to collapse
When im in fastboot mode in the bootloader, i can only find it in "device manager" as "marshall london device -> marshall london bootloader interface"
Godeske said:
When im in fastboot mode in the bootloader, i can only find it in "device manager" as "marshall london device -> marshall london bootloader interface"
Click to expand...
Click to collapse
Might seem a silly question but what phone are you using? If it is a OnePlus3 have you installed the correct drivers?
ghostofcain said:
Might seem a silly question but what phone are you using? If it is a OnePlus3 have you installed the correct drivers?
Click to expand...
Click to collapse
Pretty sure i have, but i have booked a session with oneplus costumer service now, so that they do it for me live lololol
bonham1988 said:
have you tried re-flashing the stock or twrp recovery with adb sideload command?
if not give it a shot, it might work.
Click to expand...
Click to collapse
Hey bonham,
The same thing happened to me but when I try to sideload it says I need 1.0.32 or higher to sideload this device
What should I do?
gavintoronto2016 said:
Hey bonham,
The same thing happened to me but when I try to sideload it says I need 1.0.32 or higher to sideload this device
What should I do?
Click to expand...
Click to collapse
Adb version is outdated. Just download the latest ones.
Sent from my OnePlus3 using XDA Labs
Hey guys, if there are some of you, who knows a lot about this, would you like to answer this comment? Idk maybe we could use teamviewer to help me or something
simthadim said:
In fastboot mode, did you manage to find your device on the computer? On Linux this is "sudo fastboot devices", on Windows it should be roughly similar.
Click to expand...
Click to collapse
Ohh i think i understand your question. YEs in command prompt I am able to find the device, it is connected.
(do you know a lot about this, maybe you could teamview me to help?))
Godeske said:
Ohh i think i understand your question. YEs in command prompt I am able to find the device, it is connected.
(do you know a lot about this, maybe you could teamview me to help?))
Click to expand...
Click to collapse
Hey!
I'm not the expert but I have played with my 1+3 enough to have some knowledge.
First of all, do not use "all in one tools", those do not put you in control.
Cool, so fastboot is detected, though you can't get into the recovery?
Step 1) make sure you have the latest version of "fastboot" and "adb" (Android Debug Bridge) and unlock the bootloader. This tread should be helpfull: http://forum.xda-developers.com/oneplus-3/how-to/oneplus-3-how-to-unlock-bootloader-t3398733
You need to do this, because otherwise we will not be able to proceed (i.e. the phone is to be 'unlocked' for what we are about to do).
Step 2) If you are ready than let's flash a new recovery (TWRP):
This is also step 2 in the thread mentioned above. Very important: "Once the flash has completed, Don't use the "Fastboot Reboot" Command Instead Unplug Your phone then Manually boot it into recovery by keeping Power + Volume Down button pressed."
So once you have flashed a new recovery using fastboot, than you should reboot your phone into the new recovery!
step 3)
Once in the new recovery (TWRP) go to advanced and to ADB sideload. Make sure your computer detects your device with the command "adb devices" and flash a new ROM. Just for simplicity use the official OOS 3.2.4.
This should do the trick. Before you go and try make sure you understand EVERYTHING I have written. Let me know if you have questions.
simthadim said:
Hey!
I'm not the expert but I have played with my 1+3 enough to have some knowledge.
First of all, do not use "all in one tools", those do not put you in control.
Cool, so fastboot is detected, though you can't get into the recovery?
Step 1) make sure you have the latest version of "fastboot" and "adb" (Android Debug Bridge) and unlock the bootloader. This tread should be helpfull: http://forum.xda-developers.com/oneplus-3/how-to/oneplus-3-how-to-unlock-bootloader-t3398733
You need to do this, because otherwise we will not be able to proceed (i.e. the phone is to be 'unlocked' for what we are about to do).
Step 2) If you are ready than let's flash a new recovery (TWRP):
This is also step 2 in the thread mentioned above. Very important: "Once the flash has completed, Don't use the "Fastboot Reboot" Command Instead Unplug Your phone then Manually boot it into recovery by keeping Power + Volume Down button pressed."
So once you have flashed a new recovery using fastboot, than you should reboot your phone into the new recovery!
step 3)
Once in the new recovery (TWRP) go to advanced and to ADB sideload. Make sure your computer detects your device with the command "adb devices" and flash a new ROM. Just for simplicity use the official OOS 3.2.4.
This should do the trick. Before you go and try make sure you understand EVERYTHING I have written. Let me know if you have questions.
Click to expand...
Click to collapse
Thank you, but i have not enabled "allow oem unlocking" in the developer settings when the phone worked, so i get a error message "FAILED (remote: oem unloc is not allowed)
What to do to unlock it then?
Bro, download 3.2.4 oos rom zip file from official link. Its around 1.3 GB. Just connect ur OP3 to computer. It will detect as MTP device.Im my computer it was in the name of RAIN Transfer the zip file to internal storage. Wipe cache. And select install option in TWRP and select the zip file u pushed and flash it. Best of luck..
jaganmohans said:
Bro, download 3.2.4 oos rom zip file from official link. Its around 1.3 GB. Just connect ur OP3 to computer. It will detect as MTP device.Im my computer it was in the name of RAIN Transfer the zip file to internal storage. Wipe cache. And select install option in TWRP and select the zip file u pushed and flash it. Best of luck..
Click to expand...
Click to collapse
Bro, if just it were that simple, but it's not.. It doesn't find the phone in my computer...
simthadim said:
Hey!
I'm not the expert but I have played with my 1+3 enough to have some knowledge.
First of all, do not use "all in one tools", those do not put you in control.
Cool, so fastboot is detected, though you can't get into the recovery?
Step 1) make sure you have the latest version of "fastboot" and "adb" (Android Debug Bridge) and unlock the bootloader. This tread should be helpfull: http://forum.xda-developers.com/oneplus-3/how-to/oneplus-3-how-to-unlock-bootloader-t3398733
You need to do this, because otherwise we will not be able to proceed (i.e. the phone is to be 'unlocked' for what we are about to do).
Step 2) If you are ready than let's flash a new recovery (TWRP):
This is also step 2 in the thread mentioned above. Very important: "Once the flash has completed, Don't use the "Fastboot Reboot" Command Instead Unplug Your phone then Manually boot it into recovery by keeping Power + Volume Down button pressed."
So once you have flashed a new recovery using fastboot, than you should reboot your phone into the new recovery!
step 3)
Once in the new recovery (TWRP) go to advanced and to ADB sideload. Make sure your computer detects your device with the command "adb devices" and flash a new ROM. Just for simplicity use the official OOS 3.2.4.
This should do the trick. Before you go and try make sure you understand EVERYTHING I have written. Let me know if you have questions.
Click to expand...
Click to collapse
Hey i have the same problem but this fix does not work for me.
So I have the bootloader unlocked and I can enter the bootload and my computer detects my device which is nice.
when I flash twrp on my phone trough CMD it doesnt work, my PC tells me that everything is okay but my phone will not boot into twrp and instead it will give me weird errors.
---------- Post added at 03:31 PM ---------- Previous post was at 02:56 PM ----------
this fix worked for me,
On the screen when the phone failed to md5 checksum, you've got several partition failed right? in red text.
- download this : https://www.androidfilehost.com/?fid=24591000424942573
and then extract.
- download platform tools attached below. extract in the same folder with first file you've downloaded.
- Boot your phone to fastboot mode, plug your usb, make sure adb and fastboot driver are installed.
- on the folder, hold shift and right click, click open command here
- type fastboot devices
- make sure your serial number appear.
- now flash the img of the missing file according to the partition in red text on your ms5 checksum failed one by one.
- e.g. "fastboot flash boot_aging boot_aging.img.
- make sure you flash all the missing partition.
- type fastboot reboot.
this will boot you to oos 3.1.2.
unfortunately I couldn't extract the newest oos dat. data. but you could always take the OTA
goodluck mate. sorry for my english
Godeske said:
Bro, if just it were that simple, but it's not.. It doesn't find the phone in my computer...
Click to expand...
Click to collapse
Hmm bad try installing all op3 drivers and see whether phone is detected or not. I was in the same situation previously. Pushing zip through adp terminal is painful process. I got device offline first,after solving that i got service not recognized issue. For solving that usb debugging needs to be enabled i stuck in that step.
can you enter recovery trough fastboot mode? I.e. if you are in fastboot mode you van use the volume keys to select recovery.
100% sure you can't enter recovery?
you can try Fast and pro's option. let us know!
Good day mate. My brick phone is F460S variant. I got this error when I tried to go back to Lollipop using Lg flash tool 2014, it got stuck on 5% and remove usb cable and start again, after that I got this error Secure Booting Error! Cause: boot certification verify.
No download mode
No recovery
anyone can help me please?:crying:
anyone?
You have triggered the downgrade QFUSE. There is nothing you can do apart from trying to unbrick it like it was dead, but that's not guaranteed to work. You should have researched more before attempting this. My prototype doesn't have a QFUSE, so i am free to downgrade via TOT to kitkat or lollipop.
西村大一 said:
You have triggered the downgrade QFUSE. There is nothing you can do apart from trying to unbrick it like it was dead, but that's not guaranteed to work. You should have researched more before attempting this. My prototype doesn't have a QFUSE, so i am free to downgrade via TOT to kitkat or lollipop.
Click to expand...
Click to collapse
What does QFUSE mean?
anmino said:
What does QFUSE mean?
Click to expand...
Click to collapse
I second you on this. I just uninstalled MultiROM and got the secure booting error. Depending on the ROM you have, find a bumped kernel and flash it. Most of the kernels on XDA are pre-bumped unless the developer states so. Boot into recovery, tutorials on the internet, then flash the kernel and voila.
if you can use twrp or you're able to flash, use mr_bump.zip: https://mega.nz/#!DNwhRBrK!Ki6zIzXca0KjPShi6L2oaCYIr0CkmH8sEymEt-0Q3ys
oh sorry, I didn't see "no recovery".
HardStyl3r said:
if you can use twrp or you're able to flash, use mr_bump.zip: https://mega.nz/#!DNwhRBrK!Ki6zIzXca0KjPShi6L2oaCYIr0CkmH8sEymEt-0Q3ys
oh sorry, I didn't see "no recovery".
Click to expand...
Click to collapse
Yes, no DOWNLOAD mode and RECOVERY mode.. Anyone have an idea how to fix this?
anyone?
Hello, i got the same probleme and i've trying a lot of things but not resolved..
My phone is a LG G3 Beat F470s..
Please help us..
Dowblnload adb and fastboot drivers
Download laf.img for your device
Download LG Drivers
Get you G3 to fastboot mode. Hold volume up and connect it to PC
Open fastboot and adb folder in PC, ctrl+shift+right click and open cmd. Type fastboot devices...if ur device is listen then proceed, if not u did not do something cotrectly...if yes just flash laf img to your G3 and voila
I remember me that I was in the same situation:
No TWRP, no download mode, so i have use in pat this thread:
https://forum.xda-developers.com/showthread.php?t=1752270
And an other that i haven't found again (xda thread), in some lines:
=> download the last img file from: https://eu.dl.twrp.me/d855/
=> no download mode available so no possibility to flash manually twrp file from an LG Flash Tool
==> so setup an adb connexion to the phone, cp command to copy the img file on the sdcard or where you want
=> command: "flash recovery twrp-2.8.x.x-xxx.img" (https://www.xda-developers.com/how-to-install-twrp/
=> if it's as worked, you could reboot manually in twrp, make again the partitions if needed and flash any ROM.
Hi,
I want to enable dualsim on my singlesim device and for that the TWRP has to be installed. After checking many threads, which less or more describe the same steps, I managed to unlock the bootloader and downloaded an "unofficial" twrp image for the Moto Z Play. But on the last step while trying to flash it I got the error "Image not signed or corrupt" and the image is not installed. Here is the output by flashing:
Code:
D:\Programs\Minimal ADB and Fastboot>fastboot.exe flash recovery twrp-3.1.1-0-addison.img
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
(bootloader) has-slot:recovery: not found
target reported max download size of 536870912 bytes
sending 'recovery' (11374 KB)...
OKAY [ 0.255s]
writing 'recovery'...
(bootloader) Image not signed or corrupt
OKAY [ 0.246s]
finished. total time: 0.510s
Is there a way to avoid this error ?
Use: "fastboot flash recovery twrp.img" no quotes. I change the filename to just "twrp.img" less chance of typing something wrong.
and no the .exe you did.
FSabbane said:
Hi,
I want to enable dualsim on my singlesim device and for that the TWRP has to be installed. After checking many threads, which less or more describe the same steps, I managed to unlock the bootloader and downloaded an "unofficial" twrp image for the Moto Z Play. But on the last step while trying to flash it I got the error "Image not signed or corrupt" and the image is not installed. Here is the output by flashing:
Is there a way to avoid this error ?
Click to expand...
Click to collapse
I think it is flashed. After flashing the twrp via fastboot and u see that error then just ignore it, instead directly boot your phone in recovery mode using the volume buttons and look for the word "recovery" then press on power button then it booted there.
Jimi Mack said:
Use: "fastboot flash recovery twrp.img" no quotes. I change the filename to just "twrp.img" less chance of typing something wrong.
and no the .exe you did.
Click to expand...
Click to collapse
I've changed the filename to "twrp.img" and used the command:
Code:
fastboot flash recovery twrp.img
The output is exactly the same as before.
Kap_Tutan said:
I think it is flashed. After flashing the twrp via fastboot and u see that error then just ignore it, instead directly boot your phone in recovery mode using the volume buttons and look for the word "recovery" then press on power button then it booted there.
Click to expand...
Click to collapse
unfortunatly not, after entering the recovery mode I see the message "no command" and I have to hold the power button and press volume up to enter into the Android Recovery menu.
FSabbane said:
unfortunatly not, after entering the recovery mode I see the message "no command" and I have to hold the power button and press volume up to enter into the Android Recovery menu.
Click to expand...
Click to collapse
Try to redownload the twrp again, try to use the lower version not the updated one. And after u flash that then update it with the newest one. Lets see if its work
Kap_Tutan said:
Try to redownload the twrp again, try to use the lower version not the updated one. And after u flash that then update it with the newest one. Lets see if its work
Click to expand...
Click to collapse
I've tried with the following images:
twrp-3.1.1-0-addison.img
twrp-3.1.0-0-addison.img
twrp-3.0.2-0-addison.img
which were downloaded from the url: https://www.androidfilehost.com/?w=files&flid=126925
The result is the same by all of them.
Just to be sure, the image should be copied within the "ADB/Fastboot" folder on my PC and not on the device storage/SD card, isn't it ?
FSabbane said:
I've tried with the following images:
twrp-3.1.1-0-addison.img
twrp-3.1.0-0-addison.img
twrp-3.0.2-0-addison.img
which were downloaded from the url: https://www.androidfilehost.com/?w=files&flid=126925
The result is the same by all of them.
Just to be sure, the image should be copied within the "ADB/Fastboot" folder on my PC and not on the device storage/SD card, isn't it ?
Click to expand...
Click to collapse
Did u unlock bootloader?
Yap it should be in pc adb folder
Kap_Tutan said:
Did u unlock bootloader?
Yap it should be in pc adb folder
Click to expand...
Click to collapse
Yes, I did unlock it with the unlock key received from motorola:
Code:
fastboot oem unlock UNLOCK_KEY
After that a message is displayed at each start:
your device has been unlocked and can't be trusted
ID: bad key
your device will boot in 5 seconds
Click to expand...
Click to collapse
FSabbane said:
Yes, I did unlock it with the unlock key received from motorola:
After that a message is displayed at each start:
Click to expand...
Click to collapse
After flashing twrp do not boot the phone otherwise the stock recovery will over write twrp,
After twrp is flashed while still in fastboot mode, use the volume buttons and select recovery on the menu.
flashallthetime said:
After flashing twrp do not boot the phone otherwise the stock recovery will over write twrp,
After twrp is flashed while still in fastboot mode, use the volume buttons and select recovery on the menu.
Click to expand...
Click to collapse
That was it, at each boot the recovery partition was overwritten.
Thank you very much for the help !
still doesn't work for me
FSabbane said:
That was it, at each boot the recovery partition was overwritten.
Thank you very much for the help !
Click to expand...
Click to collapse
I am still getting error saying your device is unlocked can't be trusted and will be restarted in 5 seconds,
please help me out. Also need adb zip file
velpoori said:
I am still getting error saying your device is unlocked can't be trusted and will be restarted in 5 seconds,
please help me out. Also need adb zip file
Click to expand...
Click to collapse
This is not an error. If your bootloader is unlocked this message will display at every boot.
velpoori said:
I am still getting error saying your device is unlocked can't be trusted and will be restarted in 5 seconds,
please help me out. Also need adb zip file
Click to expand...
Click to collapse
As Fandroid mentioned, it's not an error. My device also diplays it at startup.
I've added to this post a zip file that contains adb, fastboot and twrp version used to configure my device.
FSabbane said:
As Fandroid mentioned, it's not an error. My device also diplays it at startup.
I've added to this post a zip file that contains adb, fastboot and twrp version used to configure my device.
Click to expand...
Click to collapse
Have you installed twrp successfully and which OS r u running on your moto z play right now, how is it?
velpoori said:
Have you installed twrp successfully and which OS r u running on your moto z play right now, how is it?
Click to expand...
Click to collapse
I wanted twrp just to create a backup and configure my device to support dualsim. Therefore and as mentioned in a previous post, TWRP is installed only momentarly and after a reboot it would be overwritten.
My OS is the Moto Android 7.0.
What is the issue that you have now ?
FSabbane said:
I wanted twrp just to create a backup and configure my device to support dualsim. Therefore and as mentioned in a previous post, TWRP is installed only momentarly and after a reboot it would be overwritten.
My OS is the Moto Android 7.0.
What is the issue that you have now ?
Click to expand...
Click to collapse
As I told earlier I am not able to install twrp due to which I am not able to install custom rom. I tried many times to install twrp, everytime it showed "image is not found" as you guys said I tried going recovery but again it shows you already unlocked boot loader, your device can't be trusted then says " your device will reboot in 5 seconds" this is what my issue is.
velpoori said:
As I told earlier I am not able to install twrp due to which I am not able to install custom rom. I tried many times to install twrp, everytime it showed "image is not found" as you guys said I tried going recovery but again it shows you already unlocked boot loader, your device can't be trusted then says " your device will reboot in 5 seconds" this is what my issue is.
Click to expand...
Click to collapse
So that we can see where you're stuck at the moment, please follow this guide and tell us which step didn't work :
https://www.obeygeek.com/install-twrp-recovery-on-moto-z-play/
P.S.: use the adb, fastboot and twrp image I've sent you in the previous post.
FSabbane said:
So that we can see where you're stuck at the moment, please follow this guide and tell us which step didn't work :
https://www.obeygeek.com/install-twrp-recovery-on-moto-z-play/
P.S.: use the adb, fastboot and twrp image I've sent you in the previous post.
Click to expand...
Click to collapse
I will try once I reach home by 6pm, you are so helpful thank you...
FSabbane said:
I wanted twrp just to create a backup and configure my device to support dualsim. Therefore and as mentioned in a previous post, TWRP is installed only momentarly and after a reboot it would be overwritten.
Click to expand...
Click to collapse
It makes no sense then to flash it. Why don't you just use
fastboot boot twrp.img
when you want to start it? Then no flash will be involved, and twrp will be just booted for this single usage. You can repeat this whenever you need it.
After trying to flash Pie my G7 stuck in fastboot mode. Download mode is unavailable so I not can reset the stock ROM.
After it reboots it boots into only to fastboot mode and is stuck in a loop now.
An even bigger problem is that now the bootloader is locked and the unlock.bin file can not unlock the bootloader.
ADB mode is not working!
DOWNLOAD mode is not working!
SYSTEM mod does not work!
There is only FASTBOOT mode that is in the loop
Does anyone have any suggestions?
Prosjak said:
After trying to flash Pie my G7 stuck in fastboot mode. Download mode is unavailable so I not can reset the stock ROM.
After it reboots it boots into only to fastboot mode and is stuck in a loop now.
An even bigger problem is that now the bootloader is locked and the unlock.bin file can not unlock the bootloader.
ADB mode is not working!
DOWNLOAD mode is not working!
SYSTEM mod does not work!
There is only FASTBOOT mode that is in the loop
Does anyone have any suggestions?
Click to expand...
Click to collapse
Try to get into lgup to flash a kdz, if you cant do that you might be SOL
LGUP does not detect phone, download mode is not working
hi
Prosjak said:
LGUP does not detect phone, download mode is not working
Click to expand...
Click to collapse
Please contact me, I can help you recover the device
PjLyTam said:
Please contact me, I can help you recover the device
Click to expand...
Click to collapse
How to contact you and how you can help me.
If you want to help write this here to help this benefit to anyone who has this or similar problem
Thank you
Prosjak said:
After trying to flash Pie my G7 stuck in fastboot mode. Download mode is unavailable so I not can reset the stock ROM.
After it reboots it boots into only to fastboot mode and is stuck in a loop now.
An even bigger problem is that now the bootloader is locked and the unlock.bin file can not unlock the bootloader.
ADB mode is not working!
DOWNLOAD mode is not working!
SYSTEM mod does not work!
There is only FASTBOOT mode that is in the loop
Does anyone have any suggestions?
Click to expand...
Click to collapse
Fastboot --set-active=a
LameMonster82 said:
Fastboot --set-active=a
Click to expand...
Click to collapse
Thank you for your reply
The problem is that the bootloader is locked
C:\ADB>Fastboot --set-active=a
Setting current slot to 'a'...
FAILED (remote: Slot Change is not allowed in Lock State)
finished. total time: 0.003s
Problem solved
Octoplus/Octopus LG 2.9.3
Reset FRP Lock
1. Attach testpoint, and connect phone with Micro USB cable (don´t use USB hubs!).
2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn´t installed a driver.
3. Release testpoint and press "Reset FRP Lock" button.
Emergency mode
To enter emergency mode, disconnect cable, disconnect battery, press and hold "Vol+" button and connect USB cable.
My lucky day
What version of G7 use?
Sent from my LM-G710 using Tapatalk
PjLyTam said:
Please contact me, I can help you recover the device
Click to expand...
Click to collapse
i got this problem too.. please help with that
Prosjak said:
Octoplus/Octopus LG 2.9.3
Reset FRP Lock
1. Attach testpoint, and connect phone with Micro USB cable (don´t use USB hubs!).
2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn´t installed a driver.
3. Release testpoint and press "Reset FRP Lock" button.
Emergency mode
To enter emergency mode, disconnect cable, disconnect battery, press and hold "Vol+" button and connect USB cable.
My lucky day
Click to expand...
Click to collapse
how i can do this?
My G710EM has a problem with my lockback BL. I can't boot the system and it will prompt "Your device has failed a routine safety check and will not boot. This may be a temporary problem. If this message occurs repeatedly, visit this link on Another device and refer to the red case:g.co/ABH Your device will power off automatically after a while.” With LGup brush kdz brush does not go in, fastboot “fastboot flash unlock unlock.bin” prompt is invalid
* Target reported max download size of 536870912 bytes
Sending 'unlock' (1 KB)...
OKAY [ 0.004s]
Writing 'unlock'...
FAILED (remote: Flashing Unlock is not allowed
)
Finished. total time: 0.011s
I don't know what to do.
I had the very same problem as OP. I tried to install pie with LGUP (G710EM20b_00_OPEN_EU_OP_0508.kdz) but ended in fastboot loop.
After whole night of trying different things (being a noob means less sleep) I managed to run the phone in download mode. Starting from there I was able to install my previous rom. Both failed update and rescue operations were done on Win 10.
What I tried and didn't work:
- Fastboot --set-active=a
Code:
C:\ADB>Fastboot --set-active=a
Setting current slot to 'a'...
FAILED (remote: Slot Change is not allowed in Lock State)
finished. total time: 0.003s
- Unlocking with unlock.bin. Didn't save the msg but saw it somewhere in another thread. I needed to install/point drivers first because the device was not recognized in Win.
- Solutions for G6 for going into download mode. The download mode icon was displayed for a second and then going to fastboot again.
- LG Flash Tool 2014 - I just followed a guide for older phones but it didn't work. Didn't try again.
What did work:
1. I found this post on reddit (remove spaces or PM me, I'm not allowed to post links):
Code:
https:// www .reddit. com/r/LGG3/comments/2qe5sr/in_need_of_serious_help_stuck_in_fastbootno/cn5f2qr/?utm_source=share&utm_medium=web2x
Quoting the post
At first, you'll need a working fastboot environment, you'll find out how to set it up on your own. Then you'll need the laf.img, I can upload mine if you want or I could help you extracting one out of a kdz file. Put the laf.img in the same folder like your fastboot.exe, then hold shift and right click, then click on "open command panel here" or however it's called in English. Type "fastboot flash laf laf.img" (Edit: It would probably better to use "fastboot boot laf.img" instead because of the bootloader lock). If that works, you at least have a working download mode.
Click to expand...
Click to collapse
2. I used LG_Firmware_Extract_v1.2.6.1 and extracted dz file from aforementioned pie file. The I extracted two laf files for the kz file. In my case they were: laf.img_180534 and laf.img_81990.
3. I took one of these files (sry, don't remember which one, but they have the same size - didn't check if they're the same) renamed it to laf.img and put a folder where fastboot.exe is.
4. I did
Code:
fastboot boot laf.img
and voila: the phone was in download mode!
5. After that LGUP the previous rom and the phone is working again. Here I needed few tries. At first the were some problems, then I tried different combinations (1.14, 1.15, w/ and w/o uppercut). I think LGUP 1.15 (1.14 with patch) did the work. I was able to "refurbish" the phone.
Hope it's useful for others. If anyone could prepare a guide from this description or/and tell why it worked - please feel free to do so.
I think I will wait some time before trying pie again
Garlikus said:
I had the very same problem as OP. I tried to install pie with LGUP (G710EM20b_00_OPEN_EU_OP_0508.kdz) but ended in fastboot loop.
After whole night of trying different things (being a noob means less sleep) I managed to run the phone in download mode. Starting from there I was able to install my previous rom. Both failed update and rescue operations were done on Win 10.
What I tried and didn't work:
- Fastboot --set-active=a
Code:
C:\ADB>Fastboot --set-active=a
Setting current slot to 'a'...
FAILED (remote: Slot Change is not allowed in Lock State)
finished. total time: 0.003s
- Unlocking with unlock.bin. Didn't save the msg but saw it somewhere in another thread. I needed to install/point drivers first because the device was not recognized in Win.
- Solutions for G6 for going into download mode. The download mode icon was displayed for a second and then going to fastboot again.
- LG Flash Tool 2014 - I just followed a guide for older phones but it didn't work. Didn't try again.
What did work:
1. I found this post on reddit (remove spaces or PM me, I'm not allowed to post links):
Code:
https:// www .reddit. com/r/LGG3/comments/2qe5sr/in_need_of_serious_help_stuck_in_fastbootno/cn5f2qr/?utm_source=share&utm_medium=web2x
Quoting the post
2. I used LG_Firmware_Extract_v1.2.6.1 and extracted dz file from aforementioned pie file. The I extracted two laf files for the kz file. In my case they were: laf.img_180534 and laf.img_81990.
3. I took one of these files (sry, don't remember which one, but they have the same size - didn't check if they're the same) renamed it to laf.img and put a folder where fastboot.exe is.
4. I did
Code:
fastboot boot laf.img
and voila: the phone was in download mode!
5. After that LGUP the previous rom and the phone is working again. Here I needed few tries. At first the were some problems, then I tried different combinations (1.14, 1.15, w/ and w/o uppercut). I think LGUP 1.15 (1.14 with patch) did the work. I was able to "refurbish" the phone.
Hope it's useful for others. If anyone could prepare a guide from this description or/and tell why it worked - please feel free to do so.
I think I will wait some time before trying pie again
Click to expand...
Click to collapse
Thanks for you guide.. I follow it but unfortunatly after "fastboot boot laf.img" I get this message from my LG:
"Your device has failed a routine safety check.... it will reboot after a while.."
davinik84 said:
Thanks for you guide.. I follow it but unfortunatly after "fastboot boot laf.img" I get this message from my LG:
"Your device has failed a routine safety check.... it will reboot after a while.."
Click to expand...
Click to collapse
I recall I also had some error msg, it could've been the same. Now I don't remember what I exactly did next as most my actions were more or less random. Either I tried the same command but with other laf.img file (from the rom I used before), or I tried to restart the phone into download mode (vol- and power together and then vol+ after screen goes black) or tried the same file again.
Hope it helps.
davinik84 said:
Thanks for you guide.. I follow it but unfortunatly after "fastboot boot laf.img" I get this message from my LG:
"Your device has failed a routine safety check.... it will reboot after a while.."
Click to expand...
Click to collapse
I have the same problem as well. I follow the guide but I received the same error message
domenico.dalpiaz said:
I have the same problem as well. I follow the guide but I received the same error message
Click to expand...
Click to collapse
Check if the phone is recognized in LG Bridge. If so, then choose update error recovery from software update tab. Again, I don't remember if it worked immediately or did I need to reinstall drivers and/or choose a proper driver in device manager (generic ADB vs LG...) and/or restart the phone.
domenico.dalpiaz said:
I have the same problem as well. I follow the guide but I received the same error message
Click to expand...
Click to collapse
I have same error too ...
DenisVelev said:
I have same error too ...
Click to expand...
Click to collapse
Based on other threads, e.g. https://forum.xda-developers.com/v20/how-to/restore-v20-to-100-stock-bricked-devices-t3524903 and https://www.reddit.com/r/lgg6/comments/axd17d/lg_g6_eu_glh870_bricked_after_update_your_device/
try:
install the LG Bridge updater software on a computer, go to updates, click the "correct update errors" button. Then plug in your turned-off phone while holding down the volume up button. It should switch to download mode and reinstall all software from the PC. Yes, this will erase all data but it should unbrick your phone (unless the hardware's broken I guess)
Click to expand...
Click to collapse
Garlikus said:
Based on other threads, e.g. https://forum.xda-developers.com/v20/how-to/restore-v20-to-100-stock-bricked-devices-t3524903 and https://www.reddit.com/r/lgg6/comments/axd17d/lg_g6_eu_glh870_bricked_after_update_your_device/
try:
Click to expand...
Click to collapse
Cannot put in download mode. Only Fastboot. For a secound show download mode after that show fastboot mode.
I got bootloop pixel 6 pro
Pc recognize it
Only adb devices and adb fastboot cmd work
Other cmd not work.
Can anyone help me
And always blackscreen. Nothing show or display
Have you enabled USB debugging?
To enable USB debugging you need to enable Developer Options in your phone first. To do this: Go to Settings > About phone > Software info > and then tap the build number about 7 times.
Edit: I can see you have downloaded the Android SDK Platform-Tools on the desktop. Try to run the command under the correct path ( C:\Users\XXXX\Desktop\platform-tools_r33.0.2-windows\platform-tools>
RhapsodyK said:
Have you enabled USB debugging?
To enable USB debugging you need to enable Developer Options in your phone first. To do this: Go to Settings > About phone > Software info > and then tap the build number about 7 times.
Click to expand...
Click to collapse
How will he do this when he is in a boot loop?
CRXed said:
How will he do this when he is in a boot loop?
Click to expand...
Click to collapse
Indeed. I have definitely lost my mind.
Use android flashtool. You can't downgrade on official a13 and I think you have to flash it to both slots or use flashtool
Android Flash Tool
flash.android.com
CRXed said:
How will he do this when he is in a boot loop?
Click to expand...
Click to collapse
Yes i have bootloader unlock. But totally blackscreen now. Any button do not work.
If ADB and Fastboot still work (and since your bootloader is unlocked), then @fil3s suggestion to use the Android Flash Tool is the best option to try.
fil3s said:
Use android flashtool. You can't downgrade on official a13 and I think you have to flash it to both slots or use flashtool
Android Flash Tool
flash.android.com
Click to expand...
Click to collapse
Pc not recognize phone.
Nordnord said:
Pc not recognize phone.
Click to expand...
Click to collapse
Guess I misunderstood. Do ADB and Fastboot still work, or don't they? If they don't, you might want to edit your OP.
Nordnord said:
Only adb devices and adb fastboot cmd work
Click to expand...
Click to collapse
Nordnord said:
Pc not recognize phone.
Click to expand...
Click to collapse
Do you have the latest drivers and Platform Tools installed? Try different cables and/or ports?
Here screenshot
Yes driver and platform toos installed. I tried different cable and port.
Abd/fastboot devices cmd works but next like adb reboot bootloader cmd not works.
Nordnord said:
Yes driver and platform toos installed. I tried different cable and port.
Abd/fastboot devices cmd works but next like adb reboot bootloader cmd not works.
Click to expand...
Click to collapse
Are you using A to C cable?
If fastboot devices works type
Code:
fastboot reboot bootloader
Or use adb sideload
Nordnord said:
I got bootloop pixel 6 pro
Pc recognize it
Only adb devices and adb fastboot cmd work
Other cmd not work.
Can anyone help me
Click to expand...
Click to collapse
What were you trying to do, and at what point did this happen?
Is your phone recognized as a Android device, or is it showing up as something else?
Does holding down the Power button + Volume Down do anything?
Lughnasadh said:
Are you using A to C cable?
Click to expand...
Click to collapse
Yep
V0latyle said:
What were you trying to do, and at what point did this happen?
Is your phone recognized as a Android device, or is it showing up as something else?
Does holding down the Power button + Volume Down do anything?
Click to expand...
Click to collapse
Button combination not work
Not enter fastboot mode or recovery mode
fil3s said:
If fastboot devices works type
Code:
fastboot reboot bootloader
Or use adb sideload
Click to expand...
Click to collapse
Fastboot devices works
Adb reboot bootloader cmd not works
Nordnord said:
Fastboot devices works
Adb reboot bootloader cmd not works
Click to expand...
Click to collapse
Fastboot reboot bootloader cmd not works