Hello, I have a p605 with TWRP and the latest LineageOS installed.
Suddenly the tablet has an odd behaviour about charging: it charges for, say, 6-7% then it stops charging until I unplug it and plug it back... then it starts charging for another 6-7% (sometimes even 10-12%) and so on until reaching 100%.
If I charge it with screen turned on, the "charging interval" may reach 20% or 30%, but then it stops as well, forcing me to repeat the unplug-plug trick.
Besides that, the tablet isn't recognized by the pc, neither for data transfer, nor in download mode by odin (usb device not recognized in both cases). Furthermore, USB OTG isn't working at all.
I suspect it could be a hardware issue (bad usb connector).
Apart from this, the tablet is working perfectly, but I wold like to reinstall Stock 5.1.1 firmware, which apparently I can, not having access to the tablet via USB in Odin.
Is there any safe way to flash the firmware in TWRP? or does exist some modified stock-based firmware flashable via TWRP?
Thanks a lot
That is weird, I had lots of issues with Lineage OS build so I kicked it to the kerb and went with AOSP.
I too had issues charging on the Lineage ROM, I had to charge whilst on otherwise it wouldn't charge whilst off. I would try another usb cable and or another pc. Make sure Odin is version 3 and above and try flashing to the stock 5.1.1 again.
You could try going into TWRP and advanced wiping all traces of the internal storage and try download mode again or add the files on a SD card and flash from external storage in TWRP, it can be done that is how I done mine but these were custom ROMS not stock ROM's, best of luck.
try using another operating system in your PC.....
Try using windows xp(32-bit) in your pc it will absolutely show your device in odin.
follow these steps:-
1) power off your phone
2) press and hold (power button+home button+volume up button).
3) you will get into odin mode prompting you to press volume up button to continue and volume down button to reboot.
4) press volume up button.
5) open odin from your windows xp pc and connect your device to pc.
6) HOLA!!!! it will show that your device is added!!.
:good::good:
vpazzagli said:
Hello, I have a p605 with TWRP and the latest LineageOS installed.
Suddenly the tablet has an odd behaviour about charging: it charges for, say, 6-7% then it stops charging until I unplug it and plug it back... then it starts charging for another 6-7% (sometimes even 10-12%) and so on until reaching 100%.
If I charge it with screen turned on, the "charging interval" may reach 20% or 30%, but then it stops as well, forcing me to repeat the unplug-plug trick.
Besides that, the tablet isn't recognized by the pc, neither for data transfer, nor in download mode by odin (usb device not recognized in both cases). Furthermore, USB OTG isn't working at all.
I suspect it could be a hardware issue (bad usb connector).
Apart from this, the tablet is working perfectly, but I wold like to reinstall Stock 5.1.1 firmware, which apparently I can, not having access to the tablet via USB in Odin.
Is there any safe way to flash the firmware in TWRP? or does exist some modified stock-based firmware flashable via TWRP?
Thanks a lot
Click to expand...
Click to collapse
If a different PC OS or USB connecting cable don't help, search Amazon for "Charging Port Dock connector For SAMSUNG GALAXY NOTE 10.1 P600 P605 2014". I'll admit I haven't installed it yet but am planning to when I replace the original battery once charge hold is low enough. I got the "TheCoolCube" version - there are installation tips in the reviews. I figured the USB port is probably one of the higher wear/stress areas of these older tablets & it's easy to access if replacing battery.
Good luck
Related
So i discovered a strange thing from my G3 while trying to upgrade to 10E. My phone is unable to enter download mode to flash the update. I have done the procedure a in the flashing thread:
-turn off phone
-unplug USB
-hold down volume up
-plug USB
i can head windows play the device connected sound then proceed with the phone just displaying the normal charging display.
also, adb reboot download does not work, adb reboot recovery does.
PrimaryComplex said:
So i discovered a strange thing from my G3 while trying to upgrade to 10E. My phone is unable to enter download mode to flash the update. I have done the procedure a in the flashing thread:
-turn off phone
-unplug USB
-hold down volume up
-plug USB
i can head windows play the device connected sound then proceed with the phone just displaying the normal charging display.
also, adb reboot download does not work, adb reboot recovery does.
Click to expand...
Click to collapse
I had same issue, just make sure that you plug in the USB cable fast after you hold the volume up and also make sure you continue to hold the volume up.
Sent from my LG-D855 using Tapatalk
I tried a thousand times but every time it just start up mobile phone instead of going to Download Mode.
Remove the battery for a few seconds and be sure to plug into usb 2 and not into usb 3 port on your pc
I tried that too. Removed battery for seconds and connected to USB 2.0 but same issue. I wonder it connects to PC and LG Pc Suite without any problems. I'm sure all rivers are already installed but wonder why it can't enter download mode.
I lost LG original USB cable and use other cables ( I tried many ).
What's wrong then?!!! I even tried Windows XP and 8.1 but both same issue!
I'm having the same issue only I think it's because I really bricked my phone, not able to boot up or anything.
My gives me an error saying fast boot and a couple of commands with a black screen, Unable to get to download mode
Hi all, I've been using XDA for years since the original O2 XDA's and I have never had to post anything as I've always found my solution. I'm hoping somebody can assist me with a problem I have on this stock galaxy tab 3.
The device was brought to me after being thrown down the stairs. I replaced the screen and built it back up,
Removed battery connector and reconnected = nothing happens
Press power = nothing happens
press download mode = nothing happens
press recovery mode = nothing happens
Plug USB into PC = nothing happens on PC or tablet
Plug in USB mains charger and it displays battery charging logo but it doesn't fill or animate the fill then it starts the samsung boot screen. It reboots and continues to do this constantly and never ends.
I've tried two batteries and both batteries work in another tab 3 but neither batteries changed how the device works.
Thank you for any advice in advanced!!
I just received a Tab 3 lite (SM-T110) for repair, it's having a similar problem.
It does automatically turn on when plugged into charger or computer.. It is stuck on a bootloop, requiesting a Kies recovery. It does reboot when given the three finger salute (center button, volume down, and power) - it will not enter recovery mode though - same firmware error message). The device is also full off or full on, no indication of it's it's recharging or no - let the battery run out, it's off - else it's on (does not turn on or off with power button). I don't have any info how it got into this state - most likely power loss during a firmware update, but haven't ruled out other possibilities (ie bad rooting job, a custom ROM upgrade went wrong, etc). I'm not 100% concerned about cause, but hopefully I can unbrick the thing.
Anyways, I loaded Kies onto my computer and put it into recovery mode and plugged it in - nothing. Exit the recovery mode of Kies, and all of a sudden the program goes nuts trying to connect and disconnect from the device. Hmm... Okay, disconnect it, uninstall Kies, install Kies3 and try again - same thing except it complains the device is too old when the program leaves recovery mode - but same thing otherwise - does not show up in recovery mode, connects and disconnects at huge rate when not in recovery mode....
Hmmm...
Now looking at the screen, it does indicate (in the upper left hand corner) that it's in ODIN mode... So my next step I figure I'll try ODIN (although I'm researching ODIN at the moment as I haven't used it before (never had to unbrick anything from Samsung prior to now).
Okay, that was painless - downloaded and installed ODIN 3.10.7, and then downloaded the latest firmware from Samsung, extracted the firmware, added it to ODIN's AP line, then hit start to push the latest firmware onto the tablet. Good as new again.
Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Contact a software technician
juuz said:
hello,
i've got a water damaged op3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a linux logo (a small tux in the middle of the screen) and then turns off after 3 seconds. If i connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could i try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
Best regards and thanks in advance!
Click to expand...
Click to collapse
you better avoid doing experiments on op3. Symptoms you have mentioned in your thread, tells that your has been flashed (don't have usb drivers,no os,no firmware). I have faced same problem with my letv le 1s. It is a software problem. Your phone is totally empty. So do contact with any software technician, he uses sp flash tool to wake up the device. Download sp flash tool and follow procedure. If sp flash tool is detecting your device then it means your device hardware is fine.
juuz said:
Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Click to expand...
Click to collapse
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
tnsmani said:
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
Click to expand...
Click to collapse
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
juuz said:
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
Click to expand...
Click to collapse
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
tnsmani said:
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
Click to expand...
Click to collapse
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
juuz said:
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
Click to expand...
Click to collapse
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
tnsmani said:
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
Click to expand...
Click to collapse
No need to worry.. Of course, you couldn't know and there are a lot of people asking dump questions..
My phone is back a life, I guess the data transfer via USB is not working anymore, charging works although I needed to take my Oneplus One's battery (identical connector, just need to take care of the pin layout [+/-]) because my OP3 battery is pretty low and I don't know if I can reactivate it.. It has about 3,4V at the moment and charges very slow..
Finally, if anyone else faces this issue and can't boot his phone:
Try different button combinations and keep holding the buttons several seconds/minutes..
Hi users, recently I wanted to go back form miui pie to oreo using this thread : https://forum.xda-developers.com/redmi-note-5-pro/help/how-to-revert-miui-10-pie-to-miui-10-t3940244
I had some problems with flashing, phone got disconnected from pc during fastboot flashing (loose cable) and after reconnecting I couldn't flash anything so I restarted the phone. Now all I've got is black screen (the backlight works but I can't see anything) I can restart the phone when holding power button and doing the combination of power up and vol+, but it's the same. If I connect the phone to pc in this conditon nothing happens, I can't hear any sound indicating that phone is connected, nothing in device manager, I even disconnected the battery and tried the edl pins but it's the same result, pretty weird. Can anyone give me any hint?
Verity. said:
Hi users, recently I wanted to go back form miui pie to oreo using this thread : https://forum.xda-developers.com/redmi-note-5-pro/help/how-to-revert-miui-10-pie-to-miui-10-t3940244
I had some problems with flashing, phone got disconnected from pc during fastboot flashing (loose cable) and after reconnecting I couldn't flash anything so I restarted the phone. Now all I've got is black screen (the backlight works but I can't see anything) I can restart the phone when holding power button and doing the combination of power up and vol+, but it's the same. If I connect the phone to pc in this conditon nothing happens, I can't hear any sound indicating that phone is connected, nothing in device manager, I even disconnected the battery and tried the edl pins but it's the same result, pretty weird. Can anyone give me any hint?
Click to expand...
Click to collapse
You are in situation similar to me. https://forum.xda-developers.com/re...e-5-pro-unbrick-project-t3940446#post79743110
But I am still struggling with this phone, issue no resolved yet.
yawarniazi said:
You are in situation similar to me. https://forum.xda-developers.com/re...e-5-pro-unbrick-project-t3940446#post79743110
But I am still struggling with this phone, issue no resolved yet.
Click to expand...
Click to collapse
Yeah, but the point is, you can connect to pc and flash things and I can't do anything, I suspect my computer fried usb board or something on the motherboard bc it's impossible I can't get qualcomm hs-usb loader 9008.
As it turns out, after rebooting the pc, it doesn't boot anymore. Phone doesn't work and pc. Coincidence? formatting pc was needed (pc works now), could it be a virus or my power supply simply gave too much voltage to the usb? I was doing everything during the storm, y'know, thunders.. I don't know anymore, I tried even connecting to a different pc and the result is the same. I can't do anything on my phone, could it be broken usb board?
EDIT: It connects now in edl, I was shorting the pins incorrectly (can't touch the ground [shielding] while shorting the pins). Pls close this thread.
Hi, for some reason also TWRP shows from time to time different levels of battery charge (it could be around 80% at first but several seconds later after reboot it could be 3% for example), I have a typical bootloop and can use recovery and downloading modes but phone still can't load any OS properly - without USB power on it's just flashes Samsung Galaxy Note II but with USB power on it's just charging and doesn't even try to load OS (tried pretty much every ROM out there), I want to know is it solely a battery problem? Because also I had some temporal issues with SD-card and flash-drive connected by USB adapter (for some reasons they didn't mount for some time but working now again). Hoping for some tips.