Develop Bugs

rom upgrade fail Lenovo s850

hello,need some expert advice her, i bougth a Lenovo s850 from china and i needed a multilang. rom on it wich i found on needrom but when i was finshing flashing it it went into a bootlop and now its completely dead. is it any thing to do her or have i got my self a 200$ piece of junk

graatenbil said:
hello,need some expert advice her, i bougth a Lenovo s850 from china and i needed a multilang. rom on it wich i found on needrom but when i was finshing flashing it it went into a bootlop and now its completely dead. is it any thing to do her or have i got my self a 200$ piece of junk
Click to expand...
Click to collapse
Try to explain better! Do you have installed custom recovery?

no i installed a modified multi language rom from "needroom" did every as told and everything looked fine during the upgrade and when i was finished i got the green circle that says it was ok but when started it up it went in to boot loop and said "TOOL DL image fail!" but after a while its totally dead.,when i try now it wont load in any software into the phone ,just starts up the purple pre preparation on the SP flash tool but when i connect the phone it stops .cant get it into recovery mode or anything,just completely dead. i would rely be thankful for some advice her

Maybe the package you've tried to install is corrupted.

most likely, but is there anything to do with it or is it over for it.

graatenbil said:
most likely, but is there anything to do with it or is it over for it.
Click to expand...
Click to collapse
Most likely your device is unusable. Without any recovery, I dont think you will be able to do anything. I am sorry.

OK a 200$ experience richer , thanks anyway

graatenbil said:
OK a 200$ experience richer , thanks anyway
Click to expand...
Click to collapse
Just a question....are you able to enter fastboot?

no cant enter anything its like its out of battery,completely dead and it wont take charge ether

graatenbil said:
no cant enter anything its like its out of battery,completely dead and it wont take charge ether
Click to expand...
Click to collapse
hello my friend. I got exactly the same thing that I just tried to install TWRP. I stuck in Boot loop. solution found by disconnecting the battery. and making again the same procedure. but once I checked her DA DL All. Now how puts the battery is another story .but if I want i tell you, you need some tools that may have in your home..

graatenbil said:
no cant enter anything its like its out of battery,completely dead and it wont take charge ether
Click to expand...
Click to collapse
Question: When you connect the phone with your pc (usb cable) does the pc makes any sound (connected device sound)?

setmov said:
Question: When you connect the phone with your pc (usb cable) does the pc makes any sound (connected device sound)?
Click to expand...
Click to collapse
Same problem here. Trying to install twrp and got stuck in => FASTBOOT mode ...
The computer makes a sound when i connect the USB cable but i don't have adb connection.
How can I solve this problem?
Do I leave it to finnish the baterry and than try to start?

RE
leo_alex82 said:
Same problem here. Trying to install twrp and got stuck in => FASTBOOT mode ...
The computer makes a sound when i connect the USB cable but i don't have adb connection.
How can I solve this problem?
Do I leave it to finnish the baterry and than try to start?
Click to expand...
Click to collapse
The phone started in normal mode after the battery dryed and the phone went off.

Hi, has anyone Lenovo S850 firmware upgrade solution? Now I have resolve "DL Tool Image Fail" problem but have another problem - every rom I download touch screen doesn't work. On "original" rom (not multilanguage) touch screen worked properly. Does anyone have "good" multilanguage rom with touch screen working?

method to install original rom android 4.4.2 in lenovo s850
i have found the perfact solution to install original 4.4.2 rom on lenovo s850...so for that you have to donload rom from the link in notepad file...i have uploaded notepad file and download link is in that it is about 1.1 gb...so it will take time to download and after that what you have to do is open flash tool and then check da dl check sum and then extract the file you have download of 4.4.2 android and then in flash tool click on scater loading and browse to the the extraction location and in extracted folder there will be a folder somethinf target bin in that folder select scatter loding file of lenovo s850 and then just simply click on upgrade firware and then switch off your phone and then wait to process complete untill green circle come...and if you dont have flash tool...google it and download...thanks i hope this helps someone...:good::good::good::good:

Dear devs, help me out on UNBRICKING LENOVO S850:
Initial Problem was: AFTER TURNING PHONE ON (NORMAL BOOT UP) IT GOT STUCK ON BOOT LOGO.
Very first tried solution: PRESSING BOTH VOL.+POWER PHONE WENT IN LENOVO RECOVERY MODE. THEN I TRIED TO FUSE FORMAT BUT IT FAILED TO FORMAT. PROBLEM REMAINED SAME.
Second Tried Solution: DOWNLOADED OFFICIAL STOCK ROM (A. Lenovo_S850_VIBEUI_V1.5_1419_2_ST_S850_4.4.2 B.Lenovo_S850_ROW_S211_140923 C. Lenovo_S850_ROW_S207_140814. D. Lenovo S850 official firmware flash file) + ALL AVAILABLE SP FLASH TOOLS + USB VCOM DRIVER FOR MEDIATEK AND INSTALLED DRIVERS.
USING ABOVE FILES I TRIED TO DOWNLOAD ALL ROMS WITH DIFFERENT SP FLASH TOOLS VERSIONS BUT ALL THE TIME RED BAR CAME TO 100% THEN BAR STUCK ON 0% FOLLOWED BY ERROR "SDMMC WRITE FAIL".
THEN I TRIED UPGRADING FIRMWARE, SAME AGAIN IT GAVE ERROR "FORMAT FAILED"
THEN I TRIED TO FORMAT USING FLAH TOOL (ALL VERSIONS) AGAIN IT GAVE SAME ERROR "FORMAT FAILED"

crazy
ur cable problem pp

bootloop stuck d855

hello everyone ,
i need your help
i use Fulmics rom from last year but few days ago i texting from the phone . my phone sudden of then i start the phone again but it stuck on the bootloop then i try to reinstall the fulmics rom again but the problem was same. then i flash my phone with kdz method by using flash tools the phone flash show 100% but on pc its stuck on 99% then it shows error of stop working. in these all processes i also lost recovery mode when i try to go in recovery it never shows to me . pls tell me what should i do ?
one more thing i flash with another version of kdz it install and bootloop vanished but the version not supported with my device many things not working what the main reason ?

anyone?

I did not get what you said.
Explain it again with more details.

Erfan_rv said:
I did not get what you said.
Explain it again with more details.
Click to expand...
Click to collapse
i use Fulmics ROM 6.9 from last year but few days ago while texting my phone shutdown automatically then i restart the phone again but it stuck with boot-loop i try to reinstall the rom from recovery after installation the result was same. then i flash my phone with kdz global file my phone still on boot loop then i try to get back on recovery mode TWRP was automatically removed when i flashed the phone.
when i install another version of kdz file it work fine but not supported to my device but there m not facing any bootloop so what can i do now?

What do you mean not supported by my device?

Erfan_rv said:
What do you mean not supported by my device?
Click to expand...
Click to collapse
another version of kdz file which i was installed

Moto Z2 Force Sprint bricked *Please help*

Hi all! I ask your help! I have Moto z2 Force on 8.0 Oreo and I installed custom recovery twrp-3.2.1-1-nash.img and foolishly chose Slot-B and then I reboot the phone. Now when connected to a computer, it is defined as Qualcomm HS-USB QDLoader 9008 . How can I bring it back to life?! Help please! :crying:

After many attempts, it was possible to flash blankflash_from_NDX26.183-15_17. Phone reboot in fastboot and then full flash stock firmware.

yakutza said:
After many attempts, it was possible to flash blankflash_from_NDX26.183-15_17. Phone reboot in fastboot and then full flash stock firmware.
Click to expand...
Click to collapse
Samething happened to me but instead of selecting slot b my rom didnt install well so my phone is hardbrick any idea if this file will help me revive my Moto z2 force Tmobile version?

PoisonDash2 said:
Samething happened to me but instead of selecting slot b my rom didnt install well so my phone is hardbrick any idea if this file will help me revive my Moto z2 force Tmobile version?
Click to expand...
Click to collapse
This happened to me on t-mobile yesterday and I managed to solve it by downloading this: (T-Mobile only) https://drive.google.com/file/d/1fM5KLheeMYcs3yF7InOzHq6yGCOmrrbk/view
Extract the zip and while your phone is connected to your pc and booted in bootloader mode, run flash_all.bat, boot (don't flash) TWRP, install TWRP with the TWRP zip found here: https://dl.twrp.me/nash/twrp-installer-nash-3.2.1-1.zip.html
Then reboot to your newly installed TWRP recovery, factory reset, flash rom, reboot bootloader and run "fastboot -w".
After that you should boot up fine. Fastboot -w might not be necessary but I had to do it, otherwise I would boot but I would get an error message "android.process.media has stopped" without it.

Hello Friend!
Do you know if there is a solution for Moto Z2 Play? The update for Android 8 came automatically and I accepted. After a few days, he caught up and got into HardBrick! Neither the BootLoader options (power + volume (-)) are working !!
When I put it in the charger it will flash a white LED
Sorry, I'm using Google Translate

Will71000 said:
Hello Friend!
Do you know if there is a solution for Moto Z2 Play? The update for Android 8 came automatically and I accepted. After a few days, he caught up and got into HardBrick! Neither the BootLoader options (power + volume (-)) are working !!
When I put it in the charger it will flash a white LED
Sorry, I'm using Google Translate
Click to expand...
Click to collapse
If its get detect as QHUSB_BULK in conputer and installing Qualcomm drivers get it to Qh_usbloader 9008 under COMports then theres no way ti revive ur phone. Theres no Blank Flash files yet available for Moto Z2 Play

Need Help, my mi6 hard brick, no fastboot mode.. set boot partition failed

hello, my mi6 suddenly dead, hard brick, can't enter to fastboot mode. Mi6 6/128 ceramic edition.
so i decided to open back covers and shortlink 2 pins it detect as qualcomm loader in mi flash, but when flashing fastboot rom it always show error " set boot partition 1 failed "
i tried many version of mi flash and use global stable, global dev, china stable, china dev fastboot rom but always ended in set boot partition failed..
i've searching lots of forum but can't found an answer for set boot partition failed error.
i also tried QPST for flashing with fastboot rom but also give error,
please help anyone have same problem with me? or any xiaomi engineer here? i just need how to solve flashing in mi flash with error set boot partition failed.
i hope no need to change/replace the hardware...

You can try to use XiaomiTool and flash your phone with instead.
https://www.xiaomitool.com/V2/
Also, have you tried fastboot boot recovery.img
To see if you can boot TWRP or something?
(fastboot boot might work better than flashing)
I don't have any experience with Miflash, so can't offer any advice on that.
Personally I would try fastboot boot first, since XiaomiTool is in alfa-version.

-Zteam- said:
You can try to use XiaomiTool and flash your phone with instead.
https://www.xiaomitool.com/V2/
Also, have you tried fastboot boot recovery.img
To see if you can boot TWRP or something?
(fastboot boot might work better than flashing)
I don't have any experience with Miflash, so can't offer any advice on that.
Personally I would try fastboot boot first, since XiaomiTool is in alfa-version.
Click to expand...
Click to collapse
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:

zilan said:
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
Click to expand...
Click to collapse
it seems your Mi6 is alive again how was the solution?

DJ Regino said:
it seems your Mi6 is alive again how was the solution?
Click to expand...
Click to collapse
no , still dead.. :crying:

look into https://stackoverflow.com/questions/39906951/android-edl-mode-commands

zilan said:
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
Click to expand...
Click to collapse
Sorry for my late reply, I had forgotten to answer this earlier, did you try to perform a regular flash (not bricked option) from XiaomiTool. if that doesn't work either, maybe you should ask the developer of XiaomiTool2 for hints.

Try mipcsuite chiese version, i saved my Mi6 when it showed penguin in the middle of screen, no fastboot nor recovery etc

HTCDevil said:
Try mipcsuite chiese version, i saved my Mi6 when it showed penguin in the middle of screen, no fastboot nor recovery etc
Click to expand...
Click to collapse
do you have a link? and what rom to use?

zilan said:
do you have a link? and what rom to use?
Click to expand...
Click to collapse
Is there any update? Did your phone recovered from that situation?

I am in the same situation with my Asus Rog 2. It has life sign only in edl mode and when I try to recover I ve got that error too "set boot partition failed" still dead.

zenhex said:
I am in the same situation with my Asus Rog 2. It has life sign only in edl mode and when I try to recover I ve got that error too "set boot partition failed" still dead.
Click to expand...
Click to collapse
u fix it?

zilan said:
hello, my mi6 suddenly dead, hard brick, can't enter to fastboot mode. Mi6 6/128 ceramic edition.
so i decided to open back covers and shortlink 2 pins it detect as qualcomm loader in mi flash, but when flashing fastboot rom it always show error " set boot partition 1 failed "
i tried many version of mi flash and use global stable, global dev, china stable, china dev fastboot rom but always ended in set boot partition failed..
i've searching lots of forum but can't found an answer for set boot partition failed error.
i also tried QPST for flashing with fastboot rom but also give error,
please help anyone have same problem with me? or any xiaomi engineer here? i just need how to solve flashing in mi flash with error set boot partition failed.
i hope no need to change/replace the hardware...
Click to expand...
Click to collapse
if you're still there, i resolve this issue.
you need to jump charge your battery using external charger ( external charger jumped wire direct on your battery). maybe for 30mins.
then try again to charge your phone, if it reapond and have display 0% battery, let it charge for atleast 50% then power ON.
If it stucks on logo.. do reflash.

Question My Redmi Note 12 4g bricked.

I installed wrong rom then my red mi is bricked. nothing appears on the screen and when i trying to flash on miflash tool i'm taking 'cannot receive hello packet' error. what can i do?

berkantbuyukler said:
I installed wrong rom then my red mi is bricked. nothing appears on the screen and when i trying to flash on miflash tool i'm taking 'cannot receive hello packet' error. what can i do?
Click to expand...
Click to collapse
Did u unlock bootloader first?
Second, can u boot into Fastboot mode with bricked statue?
If first question is yes . Then follow these steps
________
U should have able to flash into Fastboot mode
So u can flash whole room with manual way but fast and easy with SH Script
Here's link of Tapas 4G version But (EU Rom)
https://sourceforge.net/projects/xiaomi-eu-multilang-miui-roms/files/xiaomi.eu/MIUI-STABLE-RELEASES/MIUIv14/xiaomi.eu_multi_TAPAS_V14.0.7.0.TMTMIXM_v14-13.zip/download
It's a stable rom and it has more light UI Apps So u can see mi bloatware apps got removed
And can get more functions better than global version like .. recording in calls + extended ram .. etc
Anyway
The link file has ( the rom folders and scripts .. for each OS like Windows + Mac and Lynx system)
So u can flash Those Scripts With Suitable OS that u have...
But as i said
"You Should Have Able To Boot into Fastboot Mode"
Note : when u run SH file named with
( Windows install whole rom ) or something like this.. it will take a long time so don't worry specifically when u see super (1\8)
Files got stuck
It just takes a little bit more time
After all when SH file finishes flashing ,It will automatically restart into the system.
That's all
GoodLuck

yes, i already unlocked bootloader lock but i cant boot into fastboot mode, just booting into edl mode

berkantbuyukler said:
yes, i already unlocked bootloader lock but i cant boot into fastboot mode, just booting into edl mode
Click to expand...
Click to collapse
If it's on edl mode u will need to watch this video

XBoda said:
If it's on edl mode u will need to watch this video
Click to expand...
Click to collapse
does it work normally since the tool doesn't support Note 12 yet?

Can you recover from the brick? i'm thinking in installing one of the roms available for the device...