Hello, can anyone point me on a image where does ze551ml has the cable connector on the motherboard responsoble for the touch screen digitizer? Ive got lots of screen ghost touches lately qfter screen change, tryinf to figure the problem, lose connector might be one
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It is probably the one marked by a red circle.
The other screen cable (the blue circle on the left) is only responsible for the display itself and not the touch panel.
Related
HI guys my screen is kinds messing sometimes like can't answer call , while typing becomes unresponsive etc
I am attributing it to a faulty digitizer (touch screen) so will get one from ebay
there are two types available
One with I/C
One without I/C
I have taken image from inside of my phone so that I order correct one
see image below
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks
After countless of hours diagnosis and doing trial and error in order to rectify the faulty touchscreen issue where a certain part of the touchscreen area is not working. My solution for this problem is by putting a piece of paper or hard cardboard underneath the digitizer ribbon cable just after the connector.(refer the circle part in the picture below)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hope it fix yours.
my little sister's lg g3 was dropped and shattered today. Her screen does not respond to touch but when I boot it up after a bit a message pops up. Display may be damaged, how does it know that the display is damaged is there a sensor or is it able to tell the difference in touch activity in the display?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hello, I'm clumsy and destroyed my display by dropping my phone.
So I ordered a new display, removed the old one and connected the new display and everything worked. (With open case).
Then I was ready to glue the new display in, removed all the protective foil and suddenly the touchscreen is not working anymore.
Can someone give me a hint what the problem is?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How should the small connector (Ground?, on the left side) should be attached to the inside of the phone?
Hi Guys, it's been a while since i have started seeing that white patch on my phone's display. Sometimes it goes all the way up and covers about 3/4 of screen. But here's a thing, when i give a lil bit heat to display (with heatgun, blower or whatever) these lines and patches just disappear. Is this a hardware issue or something else? Please help
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}