Related
So, long story short - I hard bricked my phone by trying to flash .bin files when they should have been .img files (rookie mistake). Anyways, once i flashed those the screen went black and the phone would not respond to anything. When i plugged the phone in it showed up as Qualcomm 9008 blah blah blah so i followed this method: http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853. I was able to flash some of my partitions but then suddenly the screen changed to this:
http://i.imgur.com/G0n16LP.jpg
I believe it was after flashing tz. Regardless, I could not flash any more partitions.
So i plugged in my battery and reconnected it to my computer and it shows up as this: http://i.imgur.com/zRKaNZC.jpg. For those who can't see it it shows up as LGE AndroidNet USB Serial Port. It also shows up as LGE AndroidNet USB Modem. Any idea on how to fix my phone from this? I've installed the Qualcomm Drivers as well as the ADB universal drivers and the LG Drivers for my phone. Using LG Mobile Support Tool the flashing goes until it says it can't connect to the phone. QPST can't see it, LG Flash Tool gives me "Model Information Check Fail" and any KDZ Flashing tool can not flash it.
I heard talk about shorting capacitors to put it into 9006 mode in order to see the partitions. Does anyone know which capacitors?
Any help would be great considering there is not a whole lot of (free) information out there on this.
Click to expand...
Click to collapse
So I fixed my phone. For everyone wondering how to do it follow this thread: http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091.
If you're stuck in the serial mode you have to short the pins on your emmc. Short then pins as described in the above thread and then plug your usb in. Then follow the steps in the thread and flash.
Man I'm in the same boat as you. I couldn't get the Qualcomm tool to work though.
Nothing seems to be working at the moment and neither flashtool or anything else seem to be finding my device.
I'd like to avoid sending it to LG if I can as I need this phone.
Have you had any luck at all?
Look's like your phone diag port. May need your msl/spc to get qualcomm tool to work.
fergie716 said:
How to Get your MSL/SPC
**NOTE** This will only work if your phone is able to turn on
Make sure you have the LG Drivers Installed on your computer (link is in 1st post for that)
Open up your dialer and enter ##DIAG#
Enable DIAG Mode
Connect your phone to your computer
On your phone change the USB Connection type to Charge Only (pull down your statusbar and click on USB Connected)
Download CdmaDevTerm on your computer(I prefer this version)
Extract the CdmaDevTermZip
Inside the extracted folder double click on the cdmaTerm file to start the application
On the right hand side of the CdmaDevTerm screen select "Scan ports"
Next select the LGE AndroidNet USB Serial Port from the drop down menu (mine was COM6) then click Connect
In the SPC/Lock Options change NV to LG from the drop down menu
Now click Read SPC
Success!
Click to expand...
Click to collapse
This looks like your phone is charging, that might mean your boot or aboot partitions are ok. Or maybe recovery, i'm not sure which one is used for phone off charging.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
jcfunk said:
Look's like your phone diag port. May need your msl/spc to get qualcomm tool to work.
This looks like your phone is charging, that might mean your boot or aboot partitions are ok. Or maybe recovery, i'm not sure which one is used for phone off charging.
Click to expand...
Click to collapse
I connected to it (I think) and got the spc number but it doesn't show up in the qualcomm tool/ i don't know what to do with the number haha.
jfedorchuk said:
I connected to it (I think) and got the spc number but it doesn't show up in the qualcomm tool/ i don't know what to do with the number haha.
Click to expand...
Click to collapse
Qualcomm tool, do you mean qpst?
if so you need to add port to server configuration tool. Or maybe try CDMAworkshop.
Have you tried volume + and USB insert?
maybe download or fastboot mode will start
jcfunk said:
Qualcomm tool, do you mean qpst?
if so you need to add port to server configuration tool. Or maybe try CDMAworkshop.
Have you tried volume + and USB insert?
maybe download or fastboot mode will start
Click to expand...
Click to collapse
Ya the qpst. I looked and the port doesn't show up as a phone. It just shows up as the serial port and won't allow me to connect. I'll look for the cdmaworkshop tool though. I'm probably going to just try to short the capactitors to get it into 9006 mode and reflash the partitions. Does anyone know where the specific capacitors are? There was a youtube video of it but the owner flipped out and made it private.... so much for advancing the community.
I tried the volume up and insert but nothing shows up. I'm curious if this were to go in for warranty if the company to fix it would be able to tell if its rooted or if they would be in the same position i am where nothing shows up.
Does it show comm7 , i know there is a box that is checked, in the add port screen, that keeps it from seeing the port. When i get home i'll take a screen shot
I too am having this exact issue.
I'm on the same boat. I don't even know how it happened since I wasn't even trying to flash a ROM. One person told me to look at tablets hard brick but I've had no luck yet. Phone was stuck in a recovery bootloop so I tried to wipe/restore backup which didn't work. Popped the battery, went to download mode, started flashing TOT, got an error (yes I had the right files), popped battery again hoping it was a bad connection but nope. I got it the other week :/ as a replacement because my G2 had hardware issues. There's gotta be a way somewhere. In the mean time, I had my gf call my service provider claiming she got a popup about an upgrade, clicked yes and came back to a black screen. They said to bring it in because it's within 14 days of the refurbished. I'm going to take it in but I'm hoping there's a way to get the phone to not load anything at all (led or the boot error during LG), or do sales reps not know enough and/or don't care enough?
I got it working!!! Somehow I got TWRP'd to boot then restored my backup of 4.4.2 stock. AT&T connecting/dropping and Baseband: "Unknown" before it randomly rebooted into download mode which I'm at now. I tried flashing TOT through COM41 but it wasn't successful. Not sure what to do now.
I had some paragraph typed and it must've not gone through. I got it back to the home screen and AT&T logo once "firmware upgrade" was an option again. I still don't know how I switched it from Qualcomm to LGE Mobile, maybe some files I deleted thinking an app backdoor'd it and injected files. After a fun and exciting 12+ hours straight with errors, bootloops, reading forums, videos, downloading/un-install. I managed a way that worked and booted back into a fresh device.
Flash Tools < BOARD_DL < Booted into Status 2
LG Suite < Restore < Fail
Flash Tools < UPGRADE_DL < Fail at 6%
Flash Tools < BOARD_DL < Fail at download mode
Device Manager < Show Hidden < Portable Devices < Un-install all MTP
Flash Tools < BOARD_DL < got to 8x% < Phone Reboot into AAT < Click < Power+Click on "Normal Boot"
LG Logo < AT&T Logo < Brand new G3
Click to expand...
Click to collapse
Hopefully this method will work for you, and who ever else has the same problem.
Here's part of the log. Not sure if hopeful or not.
[ 9:46:27] == PROPERTY INFO
[ 9:46:27] 1. download cable = USER
[ 9:46:27] 2. battery level = 77
[ 9:46:27] 3. download type =
[ 9:46:27] 4. download speed = 0
[ 9:46:27] 5. usb version = UHS
[ 9:46:27] 6. hardware revision = rev_10
[ 9:46:27] 7. download sw version =
[ 9:46:27] 8. device sw version = D85010d
[ 9:46:27] 9. secure device = S
[ 9:46:27] 10. laf sw version = 1.0
[ 9:46:27] 11. device factory version = LGD850AT-01-V10d-310-410-JUN-19-2014+0
[ 9:46:27] 12. device factory out version = LGD850AT-00-V10d-ATT-US-JUN-19-2014+0
[ 9:46:27] 13. pid = HD58S140925001695
[ 9:46:27] 14. imei = XXXXXXXXXXXXXXXXXXXX
[ 9:46:27] 15. model name = LG-D850
[ 9:46:27] 16. device build type = U
[ 9:46:27] 17. chipset platform = msm8974
[ 9:46:27] 18. target_operator = ATT
[ 9:46:27] 19. target_country = US
[ 9:46:27] 20. ap_factory_reset_status = 2
[ 9:46:27] 21. cp_factory_reset_status = 0
[ 9:46:27] 22. isDownloadNotFinish = 0
[ 9:46:27] 23. qem = 0
[ 9:46:27] 24. cupss swfv = FFFFFFFFFFF-FFFFFFFFFFF-FFFFFFFFFFF-FFFFFFFFFFF-F
[ 9:46:27] 25. is one binary dual plan = 0
[ 9:46:27] 26. memroy size = 61071360
[ 9:46:27] 27. memory_id = 032GE4
[ 9:46:27] 28. bootloader_ver = MiniOS 3.0
[ 9:46:27] LAF : Bin_User_Mode
[ 9:46:27] isValidateSecureImage Device is a qfused.
[ 9:46:27] found sbl1 Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] found aboot Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] found rpm Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] found tz Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] Secure Image Check Success
[ 9:46:27] * Set AP factory_reset= 0
[ 9:46:27] * Set qem_reset= 1
GrayNullFox said:
I'm on the same boat. I don't even know how it happened since I wasn't even trying to flash a ROM. One person told me to look at tablets hard brick but I've had no luck yet. Phone was stuck in a recovery bootloop so I tried to wipe/restore backup which didn't work. Popped the battery, went to download mode, started flashing TOT, got an error (yes I had the right files), popped battery again hoping it was a bad connection but nope. I got it the other week :/ as a replacement because my G2 had hardware issues. There's gotta be a way somewhere. In the mean time, I had my gf call my service provider claiming she got a popup about an upgrade, clicked yes and came back to a black screen. They said to bring it in because it's within 14 days of the refurbished. I'm going to take it in but I'm hoping there's a way to get the phone to not load anything at all (led or the boot error during LG), or do sales reps not know enough and/or don't care enough?
I got it working!!! Somehow I got TWRP'd to boot then restored my backup of 4.4.2 stock. AT&T connecting/dropping and Baseband: "Unknown" before it randomly rebooted into download mode which I'm at now. I tried flashing TOT through COM41 but it wasn't successful. Not sure what to do now.
I had some paragraph typed and it must've not gone through. I got it back to the home screen and AT&T logo once "firmware upgrade" was an option again. I still don't know how I switched it from Qualcomm to LGE Mobile, maybe some files I deleted thinking an app backdoor'd it and injected files. After a fun and exciting 12+ hours straight with errors, bootloops, reading forums, videos, downloading/un-install. I managed a way that worked and booted back into a fresh device.
Hopefully this method will work for you, and who ever else has the same problem.
Here's part of the log. Not sure if hopeful or not.
[ 9:46:27] == PROPERTY INFO
[ 9:46:27] 1. download cable = USER
[ 9:46:27] 2. battery level = 77
[ 9:46:27] 3. download type =
[ 9:46:27] 4. download speed = 0
[ 9:46:27] 5. usb version = UHS
[ 9:46:27] 6. hardware revision = rev_10
[ 9:46:27] 7. download sw version =
[ 9:46:27] 8. device sw version = D85010d
[ 9:46:27] 9. secure device = S
[ 9:46:27] 10. laf sw version = 1.0
[ 9:46:27] 11. device factory version = LGD850AT-01-V10d-310-410-JUN-19-2014+0
[ 9:46:27] 12. device factory out version = LGD850AT-00-V10d-ATT-US-JUN-19-2014+0
[ 9:46:27] 13. pid = HD58S140925001695
[ 9:46:27] 14. imei = XXXXXXXXXXXXXXXXXXXX
[ 9:46:27] 15. model name = LG-D850
[ 9:46:27] 16. device build type = U
[ 9:46:27] 17. chipset platform = msm8974
[ 9:46:27] 18. target_operator = ATT
[ 9:46:27] 19. target_country = US
[ 9:46:27] 20. ap_factory_reset_status = 2
[ 9:46:27] 21. cp_factory_reset_status = 0
[ 9:46:27] 22. isDownloadNotFinish = 0
[ 9:46:27] 23. qem = 0
[ 9:46:27] 24. cupss swfv = FFFFFFFFFFF-FFFFFFFFFFF-FFFFFFFFFFF-FFFFFFFFFFF-F
[ 9:46:27] 25. is one binary dual plan = 0
[ 9:46:27] 26. memroy size = 61071360
[ 9:46:27] 27. memory_id = 032GE4
[ 9:46:27] 28. bootloader_ver = MiniOS 3.0
[ 9:46:27] LAF : Bin_User_Mode
[ 9:46:27] isValidateSecureImage Device is a qfused.
[ 9:46:27] found sbl1 Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] found aboot Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] found rpm Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] found tz Partition for secure image check
[ 9:46:27] Secure Image
[ 9:46:27] Secure Image Check Success
[ 9:46:27] * Set AP factory_reset= 0
[ 9:46:27] * Set qem_reset= 1
Click to expand...
Click to collapse
I appreciate you going through this, but I don't think that you were bricked to the point that we are.
-No Download Mode
-No Recovery
-Black Screen & nothing on it.
-When plugged in via USB it shows up on the pc as: LGE AndroidNet USB Serial Port
-LG Flash Tools will not work.
-When plugged in with no battery, the screen lights up with a symbol with a battery and an exclamation point.
ElectroSh0ck said:
I appreciate you going through this, but I don't think that you were bricked to the point that we are.
-No Download Mode
-No Recovery
-Black Screen & nothing on it.
-When plugged in via USB it shows up on the pc as: LGE AndroidNet USB Serial Port
-LG Flash Tools will not work.
-When plugged in with no battery, the screen lights up with a symbol with a battery and an exclamation point.
Click to expand...
Click to collapse
That's how I was. Secure info boot < red and blue led with black screen, no factory restore. I don't know how I got TWRP to boot. I started messing around with the device manager, deleting any files stored on the computer related to any LG device (AndroidNet, QualComm, MTP, etc) along with popping the battery in with the charge screen and reading a logs.
I hope you guys can get it fixed.
Not even getting a secure info boot here. Black screen no leds
Sent from my SM-N910V using XDA Free mobile app
Same here
After rooting it and installing TRWP, I was getting an Error when rebooting into recovery "Secure Boot error". I found a solution at this page: http://forum.xda-developers.com/lg-g3/help/help-secure-boot-error-trying-to-boot-t3054977 and I was trying to replicate. At the Terminal command step "su" worked, the second line didn't, the third line worked and the final one didn't. I know that the third line bricked my phone.
dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/aboot (writes “zeroes” to the partition to “wipe” it out)
Since then the phone is almost dead. No way to wake it up, I've tried every combination of buttons and USB plugin. The only signs that is alive are that when I connect it without the battery to USB it shows the with the phone connected and the yellow triangle with a question mark and that is detected as LGE Androidnet USB and modem in the Device Manager. I tried the TOT method and the KDZ method, nothing worked. In Qpst it is detected as Phone in Download Mode and in QPST Configuration as Sahara Memory Dump (Connected Phone: Q/QCP-XXX).
LGNPST detects it as UNKNOWN, only Emergency active, and doesn't do anything when trying to upload the bin file, gives Error: Could not switch to download mode.
Getting crazy here.
What DLL did you use to get LGNPST to give you that error?
ElectroSh0ck said:
What DLL did you use to get LGNPST to give you that error?
Click to expand...
Click to collapse
The default one... LGNPST_LS970.dll It was the only one that it let me use.
alex_da_fixeru said:
The default one... LGNPST_LS970.dll It was the only one that it let me use.
Click to expand...
Click to collapse
Ah okay that makes sense. We will need a DLL specific to the model of G3 that we have. It is basically telling the program how to interact with the phone in emergency mode. I have tried the DLL's used to flash TOTs, but they will not register in Windows.
ElectroSh0ck said:
Ah okay that makes sense. We will need a DLL specific to the model of G3 that we have. It is basically telling the program how to interact with the phone in emergency mode. I have tried the DLL's used to flash TOTs, but they will not register in Windows.
Click to expand...
Click to collapse
I can't seem to find the correct .dll for LG G3. Anyone has it?
Wouldn't it be the one that came with your firmware file?
Sent from my Nexus 7 using XDA Free mobile app
danmak89 said:
Wouldn't it be the one that came with your firmware file?
Sent from my Nexus 7 using XDA Free mobile app
Click to expand...
Click to collapse
I would think that was the case, but they will not show up in LGNPST. I can get the ones to work that others have provided specifically for LGNPST, but not the ones used to flash a TOT with LG Flash Tool.
ElectroSh0ck said:
I would think that was the case, but they will not show up in LGNPST. I can get the ones to work that others have provided specifically for LGNPST, but not the ones used to flash a TOT with LG Flash Tool.
Click to expand...
Click to collapse
Ah man. I managed to get my device recognised as LGE AndroidNet USB Serial Port but there's still another driver that won't install and I don't know which one it would need to be.
Device just won't boot in to any mode, no LEDs, nothing. Obvious tools don't work like flashtool, b2bsupport. I'm considering swapping out the main board as they don't seem too expensive but I'm trying to see if I can solve this first.
I refuse to accept that this is 100% bricked.
Sent from my Nexus 7 using XDA Free mobile app
Hi, I accidentally dropped my phone but it was working fine during the day, I put it to charge before going to sleep (as usual), however when I woke up the next day it would stuck on a fastboot screen. I set it aside for one week because I was busy and had an extra device. But now that I have free time, I was trying to follow a tutorial (link below)... I dowloaded some drivers and the lg fastboot tool, the tutorial was working until the point where I have to erase the recovery partition (using the command "fastboot erase recovery") since it would lead me to a "failed to erase partition" error. On the phone, the message I get is "Failed writing block @1" (All the logs are found below). Can anybody help me out, is there anything I can do or is my phone dead?
Image of my CMD after trying the command: http://i.imgur.com/fJ6e0cZ.png
Written log (cmd):
HTML:
C:\platform-tools>fastboot erase recovery
erasing 'recovery'...
FAILED (remote: failed to erase partition)
finished. total time: 5.036s
Log of my cell phone: http://i.imgur.com/HerWF5r.jpg
Written log (cell phone):
HTML:
[16510] fastboot_init()
[16510] Error: allocating memory for ssd buffer
[16540] USB init ept @ 0x7ad0000
[16560] udc_start()
[16660] -- reset --
[16660] -- portchange --
[16780] fastboot: processing commands
[31860] fastboot: getvar: partition-type: recovery
[31860] fastboot: erase:recovery
[31890] Error: Command never completed
[31860] Error: Command timeout error
[31860] Error: Command completed with errors
[31860] Failed Writing block @ 1
Note 1* Tutorial I was trying to follow: http://forum.xda-developers.com/android/general/unbrick-lg-model-download-recovery-t3060184
Try to get into download mode.of you can't.
Then follow exactly .
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
Jahanzaibawan said:
Try to get into download mode.of you can't.
Then follow exactly .
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
Click to expand...
Click to collapse
Hi Jahan, thanks for the help. I couldn't access download mode, so I tried the tutorial you addressed, installed the right drivers (I suppose), but for some reason Qualcomm 9008 ports won't appear here, any clue of what this could be?
My device manager: http://i.imgur.com/1l6UmZo.png
Driver: http://i.imgur.com/0ktujaQ.png
Driver setup: http://i.imgur.com/94U7BjZ.png
decoderxda said:
Hi Jahan, thanks for the help. I couldn't access download mode, so I tried the tutorial you addressed, installed the right drivers (I suppose), but for some reason Qualcomm 9008 ports won't appear here, any clue of what this could be?
My device manager: http://i.imgur.com/1l6UmZo.png
Driver: http://i.imgur.com/0ktujaQ.png
Driver setup: http://i.imgur.com/94U7BjZ.png
Click to expand...
Click to collapse
What's your g3 model?
Jahanzaibawan said:
What's your g3 model?
Click to expand...
Click to collapse
It's a D855
decoderxda said:
It's a D855
Click to expand...
Click to collapse
It should work.try shortening the pins as exactly described in the given tutorial.follow each step carefully.
Brick hard Moto Z Play
Fellows, I hope you help me please with the Blankflash file for the MZP.
I left it in full brick, I was tunneling MM and Nougat down with the script Downgrade and coming up with adb sideload and it happened when installing Nougat again.
It should be mentioned that it was with the April patch, the downgrade of a patch MM, restart and install the apps as always and personalize, then added in December, reboot and reinstall No but end instead of restart, I chose to start The bootloadder and alli brickeo.
Everything only with the charger open, no root or any modification, now no garment or anything and if I connect it to the charger of the PC only the charge led flashes, when I connect it the PC recognizes me as ¨Qualcomm hs-usb qdloader 9008 COM5¨ has used and Blankflash for the bike does not finish the process and the 1,2 and 3 dce XDA and neither.
If someone can pass me the Blankflash will thank you, please.
I arrived here:
Blur_Version.25.211.10.addison.retail.es.ES - Security April 2017
NPN 25.137-24-1-9
Download here:
Blur_Version.24.221.12.addison.retail.es.ES - Security November 2016
MPNS24.104-44-10
Install this:
Blur_Version.24.231.19.addison.retail.es.ES - Security December 2016
MPNS24.104-44-16
Then bricke it at the end of the process:
Blur_Version.25.21.2.addison.retail.en.US - Android 7.0 Nougat January 2017
NPN25.137-15.2
By the way a colleague Ali Guzman of the group facebook my pass this compilation NPN25.137-24-1 with the included blankflash but in the middle of the process notifies me of package error.
I pass the link for a man who serves:
Https://mega.nz/#!nMdEFLxY!4x0BZWr45...anoX16JZv5B5-E
thank you very much.
I hard bricked my Moto X2 last year and I'm still waiting for the blankflash files for it. So far, nothing....
As far as I know only a few of the older (still under Google flag) devices have it, like G1 and X1. No other blankflash files were made available after that I'm afraid....
password of mega link?
bruno-prata13 said:
password of mega link?
Click to expand...
Click to collapse
lenovo-forums.ru
you check this page.
lozada81 said:
lenovo-forums.ru
you check this page.
Click to expand...
Click to collapse
I met exactly the same issue like you, applied April patch, did downgrade to 6.0, doing ota again, then it happened...
BTW "lenovo-forums.ru" doesn't work as the decryption key
lanyao1920 said:
I met exactly the same issue like you, applied April patch, did downgrade to 6.0, doing ota again, then it happened...
BTW "lenovo-forums.ru" doesn't work as the decryption key
Click to expand...
Click to collapse
pass of file : lenovo-forums.ru
http://lenovo-forums.ru/files/file/...ialnaya-proshivka-xt1635-02_70_npn25137-24-1/
I am having the same problem....did you manage to solve it?
tiberiuharcsa said:
I am having the same problem....did you manage to solve it?
Click to expand...
Click to collapse
Me? No, I guess we have to wait for the blankflash file... Or the question would be: How can we extract that file from the OTA, or on a April patched phone which still is alive?
debrick.img file for moto z play
please upload debrick.img for moto z play.... my phone is hard bricked and unable to start or boot
So who distributes the blankflash? I'm stuck with led flash on charge. Damn April update
Sent from my SM-G955U using Tapatalk
moto z play xt1635-02
even im suffering the same problem just charging led blinks when i connect the phone and nothing happens
please provide us the blankfalsh files
So has this happened only after applying the April patch and then downgrading? I've downgraded from the January patch, then OTA'd to N + February, then the March patch without any issues, and I'm wondering if I'll meet the same fate whenever the next time I get prompted for an OTA.
My Moto z Play Hardbricked too. When i use blank-fash.bat show these error:
"Motorola qboot utility version 3.37
[ -0.000] Opening device: \\.\COM10
[ 0.001] Detecting device
[ 0.005] ...cpu.id = 70 (0x46)
[ 0.005] ...cpu.sn = 1200899435 (0x4794456b)
[ 0.005] Opening singleimage
[ 0.005] Loading package
[ 0.009] Failed identify board. Wrong package?
[ 0.011] ERROR: error loading package
[ 0.011] Check qboot_log.txt for more details
[ 0.011] Total time: 0.011s
FAILED: qb_flash_singleimage()->error loading package"
My bike z play is just with the flashing led someone help me to revive
after update my moto z play got black screen nono response , just when i plug the mobile in pc, usb active but cant flash or dome anything , now my mobile in hospital shop company , they said its flash damage from update :\
assanches said:
My Moto z Play Hardbricked too. When i use blank-fash.bat show these error:
"Motorola qboot utility version 3.37
[ -0.000] Opening device: \\.\COM10
[ 0.001] Detecting device
[ 0.005] ...cpu.id = 70 (0x46)
[ 0.005] ...cpu.sn = 1200899435 (0x4794456b)
[ 0.005] Opening singleimage
[ 0.005] Loading package
[ 0.009] Failed identify board. Wrong package?
[ 0.011] ERROR: error loading package
[ 0.011] Check qboot_log.txt for more details
[ 0.011] Total time: 0.011s
FAILED: qb_flash_singleimage()->error loading package"
Click to expand...
Click to collapse
I'm with the same error....
So we already have 8, 9 bricks until now...
Guys, they are doing me the favor of helping me in the problem of hard brick by doing downgrade from the patch of April and try to return to nougat, apparently the something serious and the teacher who is helping me is verifying from the binary singleimage file. Bin since when executing mark error in the package, reading and the teacher makes me incapie in the fact of the reading of the device:
... MSM8953 unknown.
I show them the image where all the blankfash that if they execute mark the same error.
https://www.mediafire.com/?5offclm2900bucp
lozada81 said:
Guys, they are doing me the favor of helping me in the problem of hard brick by doing downgrade from the patch of April and try to return to nougat, apparently the something serious and the teacher who is helping me is verifying from the binary singleimage file. Bin since when executing mark error in the package, reading and the teacher makes me incapie in the fact of the reading of the device:
... MSM8953 unknown.
I show them the image where all the blankfash that if they execute mark the same error.
https://www.mediafire.com/?5offclm2900bucp
Click to expand...
Click to collapse
For me the same, I guess we need a new version blank-flash file which suites to the new BL version.
It is correct, already published a nougat firmware updated to April with which I confirm that the bootloader was updated to its
version C1.07.
The packed does not have more than the partitions to flash and update but hopefully the scholars in the subject can help us with a blankflash and or until motorola releases and get out of this problem so frustrating.
I share the link
Https://www.androidfilehost.com/?fid=961840155545567726
I share the link where they find blankflash android 6 and 7; Maybe somebody will get to work on the problem of brick or hard brick since it is very difficult to find things related to the subject.
Http://lenovo-forums.ru/files/category/140-moto-z-play/
H731 Flash Problem
Show Lg H736p (Main Board Model)
in Setting H731 Model
i Flash The Phone reason Virus In Phone
but Phone Not Goes To Download Mode
try To Download Mode than The Phone Goes To Black Screen
and show
"[730] udc_start()"
phone in fastboot mode in Divece manager
than I try laf.img (Extracted From Firmware)
Writing laf Also Error
"writing 'laf'...
FAILED (remote: unknown command)"
so please help me ! how i can Flash My phone.
Hi everybody.
As I know that it is possible that someone wants to know why I need a deep cable here is a super summary of my catastrophe:
I made a root in my Z2 Force with the bootloader unlocked (thanks to the number that Motorola gives to do that) and with the SU, after that I knew (not before, damn) that some applications don't work on root cell phones (****) among these my bank app, Netflix app, Fox app (**** **** ****), even using the Root Cloak app and others like that the result is that they don't work, so I needed to return to the unroot state, until there everything manageable, buuuuuuuuut, when I had to flash the stock ROM I downloaded the wrong version (fuuuuuuuck), the result was that the cell phone doesn't recognize the SIM cards, doesn't allow the use of WIFI, my IMEI was lost (wtf!) and when I try to flash again (in fastboot) with the correct ROM stock the bootloader doesn't leave me because it says "Flashing_locked", (what? but if I already unlocked it before !, well no, the ****ing cell phone doesn't recognize that, if I try to unblock it through the fastboot commands give as results that the process was satisfactory, but when restarting the bootloader it says NO, I'm still locked mother****er ! ...........
Well, that's why I need a deep cable, to flash with the (foolish) "Flasing_locked" status. So, the problem is basically that I found on the Internet those who do the deep cable with micro-usb, I haven't found how to do it with a usb-c cable. In the cases with micro-usb you only have to bridge the black and green wires and "ta dah" everything is done, in others I also see in micro-usb the pin 4 is jumpered with pin 1 in the micro-usb connector, but on the usb-c cable I have something like 20 pins and more than 4 cables, so I don't know how I can do the deep cable with a usb-c.
Please, I need help :crying:
I think there is another way to go about this than putting your devices into Qualcomm 9008. That is what you are wanting the EDL Deep Cable for, right? Instead of that, why not try this thread here, https://forum.xda-developers.com/z2-force/how-to/how-to-return-to-stock-sprint-t3694783, and see if Uzephi's method doesnt get you back to stock. If for some reason his flashall doesnt work, then I would suggest using a blankflash for your version of Android to wipe the slate clean and then use the return to stock method for your device.
fast69mopar said:
I think there is another way to go about this than putting your devices into Qualcomm 9008. That is what you are wanting the EDL Deep Cable for, right? Instead of that, why not try this thread here, https://forum.xda-developers.com/z2-force/how-to/how-to-return-to-stock-sprint-t3694783, and see if Uzephi's method doesnt get you back to stock. If for some reason his flashall doesnt work, then I would suggest using a blankflash for your version of Android to wipe the slate clean and then use the return to stock method for your device.
Click to expand...
Click to collapse
Okay ! I'm going to try those two options and I'll write you what happens.
Thanks !
Well, I'm here again.
I tried the two methods that you kindly indicated to me:
1. https://forum.xda-developers.com/z2-...print-t3694783 The Flashall.bat file really does not do anything different than being an automated flash of what you can usually do manually, I mean, it does the flash using the fastboot file by file, so because it's the same process (but automated) I got the same result, when the Flashall.bat file tries to send / flash the files the response status is Failed, because the flashing status in the bootloader is locked.
2. Blankflash metod. This method seems to work when the cell phone is bricked and does not enter the bootloader, and that is not my case because I can access the cell phone, for example if I connect the cell phone to the computer in:
a) the boot manager mode, the "Device Manager" recognizes it as "Android Device / Motorola ADB Interface"
b) started the ROM (and activated the "USB Debugging"), the "Device Manager" also recognizes it as "Android Device / Motorola ADB Interface"
c) QCOM mode (selected from the bootloader) the "Device Manager" recognizes it as "Qualcomm HS-USB Diagnostics 9092".
Anyway, if I run the blank-flash file in:
a) bootloader mode, the CMD shows "waiting device" and does nothing
b) started the ROM (and activated the "USB Debugging"), the CMD shows "waiting device" and does nothing
c) QCOM mode (selected from the bootloader), the CMD shows "waiting for the device" and does nothing (this same result with or without the activation of "USB Debugging")
So I'm still the same, I think my only option is Deep Cable, what do you think?
Loperaco said:
Well, I'm here again.
I tried the two methods that you kindly indicated to me:
1. https://forum.xda-developers.com/z2-...print-t3694783 The Flashall.bat file really does not do anything different than being an automated flash of what you can usually do manually, I mean, it does the flash using the fastboot file by file, so because it's the same process (but automated) I got the same result, when the Flashall.bat file tries to send / flash the files the response status is Failed, because the flashing status in the bootloader is locked.
2. Blankflash metod. This method seems to work when the cell phone is bricked and does not enter the bootloader, and that is not my case because I can access the cell phone, for example if I connect the cell phone to the computer in:
a) the boot manager mode, the "Device Manager" recognizes it as "Android Device / Motorola ADB Interface"
b) started the ROM (and activated the "USB Debugging"), the "Device Manager" also recognizes it as "Android Device / Motorola ADB Interface"
c) QCOM mode (selected from the bootloader) the "Device Manager" recognizes it as "Qualcomm HS-USB Diagnostics 9092".
Anyway, if I run the blank-flash file in:
a) bootloader mode, the CMD shows "waiting device" and does nothing
b) started the ROM (and activated the "USB Debugging"), the CMD shows "waiting device" and does nothing
c) QCOM mode (selected from the bootloader), the CMD shows "waiting for the device" and does nothing (this same result with or without the activation of "USB Debugging")
So I'm still the same, I think my only option is Deep Cable, what do you think?
Click to expand...
Click to collapse
To use blankflash you need to be in 9008 mode, since you have adb working try issuing the command 'adb reboot-edl' or 'adb reboot edl' can't recall at the moment. You'll know when you're in edl/9008 mode because the screen will be blank and the device will recognize as 9008. If you can't reboot to edl through adb, go to fastboot and try 'fastboot oem blankflash' again you'll know when you're ready for blankflash because the device will recognize as 9008. If the commands don't take, boot into QCOM mode and try 'fastboot oem blankflash'
*To unlock the bootloader you need to select oem unlock in settings. If it's greyed out you need to connect to internet and sign into google. Try bluetooth connection or a cable since wifi and mobile is borked at the moment.
41rw4lk said:
To use blankflash you need to be in 9008 mode, since you have adb working try issuing the command 'adb reboot-edl' or 'adb reboot edl' can't recall at the moment. You'll know when you're in edl/9008 mode because the screen will be blank and the device will recognize as 9008. If you can't reboot to edl through adb, go to fastboot and try 'fastboot oem blankflash' again you'll know when you're ready for blankflash because the device will recognize as 9008. If the commands don't take, boot into QCOM mode and try 'fastboot oem blankflash'
*To unlock the bootloader you need to select oem unlock in settings. If it's greyed out you need to connect to internet and sign into google. Try bluetooth connection or a cable since wifi and mobile is borked at the moment.
Click to expand...
Click to collapse
Hi.
I have fresh news.
The first thing I tried was to enable the option to unlock the OEM because that option was in gray, try to connect the internet via USB cable and no option worked, but when connecting by bluetooth (which is not easy either for those who don’t know how) I did it! and once connected, I enabled the option again, so I activated it to allow me to unlock the OEM, but when restarting the bootloader to verify it was still showing the status "Flashing_locked" (sad face).
Even knowing this, try the options in this order and with these results:
1. Try the command 'adb reboot-edl' or 'adb reboot edl'. The first command that the console recognized was 'adb reboot -edl' but once accepted by the CMD the cell phone was rebooted alone and went back to the ROM, that is, it was not blank.
2. Go to fastboot and try 'fastboot oem blankflash'. When doing this the result obtained in the CMD was “(bootloader) Command Restricted FAILED (remote failure) finished. total time: 0.006s”, probably due to the fact that the bootloader still indicates "Flashing_locked".
3. Boot into QCOM mode and try 'fastboot oem blankflash'. When I start the QCOM option from the bootloader the cell phone automatically loads the ROM, after this I activated the USB Debugging and ran the command in question but the result was "<waiting for any device>" and nothing happens. I tried the command again without activating the USB Debugging and nothing happened either. If I enter the command "fastboot devices" the command does not give any results, I give way to the next line as if nothing happened.
4. I was sad after all this so I decided to retry everything, starting with the command to put the phone in mode 9008, so, just out of curiosity I tried the second sentence you wrote, that is, 'adb reboot edl' (without the line in the middle before the word “edl”), this command also recognized it but this time if it went to blank (yeah !!!). So after accomplishing this I followed the instructions of https://forum.xda-developers.com/z2-force/help/hard-bricked-blankflash-z2-force-t3705789, but the result when executing the Blank-Flash file was:
[ 0.000] Opening device: \\.\COM11
[ 0.001] Detecting device
[ 0.004] ...cpu.id = 94 (0x5e)
[ 0.005] ...cpu.sn = 3632543294 (0xd884363e)
[ 0.005] Opening singleimage
[ 0.005] Loading package
[ 0.009] ...filename = pkg.xml
[ 0.012] Loading programmer
[ 0.012] ...filename = programmer.elf
[ 0.013] Sending programmer
[ 0.091] ReadFile() failed, GetLastError()=0
[ 0.644] Unexpected command, expecting 3 or 18 or 4, got 1 instead.
[ 0.644] ERROR: sahara_download()->general error
[ 0.644] Check qboot_log.txt for more details
[ 0.645] Total time: 0.646s
[ 0.645]
[ 0.645] qboot version 3.85
[ 0.645]
[ 0.645] DEVICE {
[ 0.645] name = "\\.\COM11",
[ 0.645] flags = "0x64",
[ 0.645] addr = "0x28FD74",
[ 0.645] sahara.current_mode = "0",
[ 0.645] api.buffer = "0x2160020",
[ 0.645] cpu.serial = "3632543294",
[ 0.645] cpu.id = "94",
[ 0.645] cpu.sv_sbl = "0",
[ 0.645] cpu.name = "MSM8998",
[ 0.645] storage.type = "UFS",
[ 0.645] sahara.programmer = "programmer.elf",
[ 0.645] api.bnr = "0x20C7ED0",
[ 0.645] }
[ 0.645]
[ 0.645]
[ 0.645] Backup & Restore {
[ 0.645] num_entries = 0,
[ 0.645] restoring = "false",
[ 0.645] backup_error = "not started",
[ 0.645] restore_error = "not started",
[ 0.645] }
[ 0.645]When executing the "blank-flash" file again, the result obtained was:
[ 0.000] Opening device: \\.\COM11
[ 0.001] Detecting device
[ 34.005] ERROR: sahara_greet_device()->change_mode()->do_hello()->IO error
[ 34.005] Check qboot_log.txt for more details
[ 34.005] Total time: 34.006s
[ 34.005]
[ 34.005] qboot version 3.85
[ 34.005]
[ 34.005] DEVICE {
[ 34.005] name = "\\.\COM11",
[ 34.005] flags = "0x64",
[ 34.005] addr = "0x28FD74",
[ 34.005] api.bnr = "0x612CA8",
[ 34.005] }
[ 34.005]
[ 34.005]
[ 34.005] Backup & Restore {
[ 34.005] num_entries = 0,
[ 34.005] restoring = "false",
[ 34.005] backup_error = "not started",
[ 34.005] restore_error = "not started",
[ 34.005] }
[ 34.005]I thought I had made a worse mistake, but turning off the cell phone normally returned to enter the ROM without problem.
At this point I was left with no more ideas...
You need drivers so that your pc and the phone can communicate, here is a link and it also has a verified blankflash.zip that has worked many times for others in the past. The process is a bit hit and miss, meaning it can be finicky on some pcs. Make sure you use a usb 2.0 port off the mobo, and not a 3.0+ or a hub port, they're not all so universal and can cause problems, so stick to 2.0 mobo ports.
https://forum.xda-developers.com/showpost.php?p=77623934&postcount=5
41rw4lk said:
You need drivers so that your pc and the phone can communicate, here is a link and it also has a verified blankflash.zip that has worked many times for others in the past. The process is a bit hit and miss, meaning it can be finicky on some pcs. Make sure you use a usb 2.0 port off the mobo, and not a 3.0+ or a hub port, they're not all so universal and can cause problems, so stick to 2.0 mobo ports.
https://forum.xda-developers.com/showpost.php?p=77623934&postcount=5
Click to expand...
Click to collapse
Hiiiii.
Well, the file in the forum that you gave me works! I mean, it does something new, it generates a successful process and it was reinitiated to the bootloader, once there I noticed that there was a changed item "Software status: Official" (previously said modified), but the ítem of "Flashing_locked" is still the same ...
Anyway I tried to flash the stock ROM with that and I have the same result whenhen I get to the command "fastboot flash bootloader bootloader.img", here are the results:
(bootloader) is-logical:bootloader: not found
Sending 'bootloader' (9884 KB) OKAY [ 0.266s]
Writing 'bootloader' (bootloader) Validating 'boot
loader.default.xml'
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) flash permission denied
(bootloader) Cancelling 'bootloader.default.xml'
FAILED (remote: '')
fastboot: error: Command failed
Another new thing found: in "bootloader logs" mode it says:
SSM: abl cvs roll back 0,1
Fastboot Reason: UTAG bootmode configured as fastboot
I feel that I am closer to each step, please continue to help me.
What firmware are you trying to flash? At this point it might be easier to use the lenovo moto smart assistant tool to do a rescue on your phone. Do a 'fastboot reboot bootloader' to get a fresh bootloader session, and run the lmsa tool and see it it will recover your phone. Either way, let me know what firmware you're trying to flash.
First of all, you need to make sure you are xt1789-? ? If x is 3, then he is the s version. You only need to install the rom of the corresponding carrier. I remember that the installation tool can choose whether to install the baseband and bp/bl lock (maybe)So your xt1789-? ? What is it?
Refer to the version number in the link image https://m.facebook.com/story.php?story_fbid=624595458056701&id=100015187571561
41rw4lk said:
What firmware are you trying to flash? At this point it might be easier to use the lenovo moto smart assistant tool to do a rescue on your phone. Do a 'fastboot reboot bootloader' to get a fresh bootloader session, and run the lmsa tool and see it it will recover your phone. Either way, let me know what firmware you're trying to flash.
Click to expand...
Click to collapse
Hi again !
I followed his advice to use the "lenovo moto smart assistant tool" but as a result I got that my device isn't supported by the software (see attached image).
On the other hand, regarding the firmware that I'm trying to recover, I don't know if I remembered that I told him to install a wrong ROM at the beginning of my problem, and I never backed up my original ROM, so I do not really have the least idea of what is my stock ROM (for Colombia - South America), if I search for firmware I find many categorized with letters at the beginning (AMXBR, AMXCO, AMXLA, AMXMX, ATT, ATTM, LRA, OPENMX, RETAIL, RETAPAC, RETBR, RETCN, RETEU, RETIN, RETLA, RETRU , SPRINT, TEFBR, TIMBR, TIMIT, TMO, USC, VFEU, VZW) ... investigate how I can know which was the original of my phone (after having made a mess) and can not find any reference in this regard.
I keep trying.
潇霄小云 said:
First of all, you need to make sure you are xt1789-? ? If x is 3, then he is the s version. You only need to install the rom of the corresponding carrier. I remember that the installation tool can choose whether to install the baseband and bp/bl lock (maybe)So your xt1789-? ? What is it?
Refer to the version number in the link image https://m.facebook.com/story.php?story_fbid=624595458056701&id=100015187571561
Click to expand...
Click to collapse
Hi 潇 霄 小云!
I am sure it is an XT1789-05 however I do not know which firmware corresponds to me (never look before deleting my stock ROM) and when looking for the firmware of my device there are many with many letters at the beginning (AMXBR, AMXCO, AMXLA, AMXMX, ATT, ATTM, LRA, OPENMX, RETAIL, RETAPAC, RETBR, RETCN, RETEU, RETIN, RETLA, RETRU , SPRINT, TEFBR, TIMBR, TIMIT, TMO, USC, VFEU, VZW), so I do not know which one corresponds to me for Colombia (South America).
You can not see my model in the image you send me ...
Thanks for the help, I'm still investigating!
Loperaco said:
Hi again !
I followed his advice to use the "lenovo moto smart assistant tool" but as a result I got that my device isn't supported by the software (see attached image).
On the other hand, regarding the firmware that I'm trying to recover, I don't know if I remembered that I told him to install a wrong ROM at the beginning of my problem, and I never backed up my original ROM, so I do not really have the least idea of what is my stock ROM (for Colombia - South America), if I search for firmware I find many categorized with letters at the beginning (AMXBR, AMXCO, AMXLA, AMXMX, ATT, ATTM, LRA, OPENMX, RETAIL, RETAPAC, RETBR, RETCN, RETEU, RETIN, RETLA, RETRU , SPRINT, TEFBR, TIMBR, TIMIT, TMO, USC, VFEU, VZW) ... investigate how I can know which was the original of my phone (after having made a mess) and can not find any reference in this regard.
I keep trying.
Click to expand...
Click to collapse
Well your device is showing -05, that's Mexico and South America I believe. There should be a model printed by the charge port on the phone. As for which firmware, look at your sim and see if you can get an idea from there, or if you can ask whomever you got your phone from. Do you remember what provider was listed under the software update channel originally? Your sim should be able to get you some info as to who the provider is even if it's just a subsidy of a major carrier.
Hi there !
Well today I have very good news!
At last I managed to reinstall everything. How it happened? So I went back to the steps in this way:
1. Having a wrong ROM version (it does not correspond to my stock) connect by bluethooth the cell phone to access the internet, so the cell phone recognized that the OEM had already been authorized and allowed me to access the option and change it (because before it was gray).
2. Go to the bootloader and find the indication "Flashing_locked", but as I knew I had already given the authorization from within the ROM I opened a console and wrote the command "fastboot oem unlock" AND RECOGNIZED IT!, Restart the bootloader and voila! the message already said "Flashing_unlocked"
3. After this it was a matter of trying (without lying) something like six firmware XT1789-05 version because I had no idea what mine was, it took me a long time because some left me without Wi-Fi again, but Finally, I managed to locate one that looked like the one I had (RETLA XT1789-05_NASH_RETLA_DS_8.0.0_OPXS27.109-34-19_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml), so I tried hard there, but still shows a warning that a version is installed of the different operating system, but it works for me and that's how it will stay for a couple of months.
4. Then I was able to install the TWRP and the Magisk without any problems.
5. Problems that I had: Warning of the bootloader without blocking, Notice of the different operating system, Application of finding my device does not work (it stays looking for the cell phone and never locates it).
Many thanks to 41rw4lk, without your help this would have been impossible.
I hope to share my experience with someone else who may have my problem or something like it!
Postscript: Finally, they never gave me instructions on how to make the Deep Cable when the cell phone is a USB-C type port (lol), so if the data appears I would still be interested only in general knowledge.