Develop Bugs

Z1C won't start - advice please

I've got myself into quite a muddle with my rooted Z1 Compact. I was prompted to update the firmware to 14.4.A.0.157, which I did over the air. Since the update, the device had been freezing, restarting and generally being unwell. What I didn't realise, based on a piece I read somewhere, was that this was likely or probable if the phone had been rooted. My memory is a bit sketchy on all the steps I took - but briefly - it suggested checking the status of the phone, from which I followed instructions using flashtool to flash a preceding firmware (xxxx.108), which it appeared to do successfully but now the phone does not boot at all. I'm now lost what to do next and I couldn't say if I've soft or hard bricked the phone. Another article (at android.gs / unbrick-sony-xperia-z1 ) says that if it's hard bricked then I need to flash the full firmware (not just kernel only). I've downloaded and installed Emma from Sony's site. I can get the software to recognise the phone but it says it is locked and I am in the process of downloading the Android SDK to [see if I can] continue this process.
I should have stopped and asked for advice before I did any of this. Now finally I am pausing to seek advice. Can anyone point me in the right direction?
The phone will charge when plugged in, at least it is showing a green LED to imply fully charged.

Brief update: I couldn't enable USB debugging on device, as device doesn't start up. I enter fastboot mode when connecting the device (Windows) and I run "fastboot devices" in the platform-tools folder without an error however when I enter the command with my unlock key, I just get "waiting for device" (several minutes). I am assuming that this might be because I couldn't enable USB debugging on the device? Any suggestions on where to go from here?

I might as well log the antics of my adventurous mind. Given that I hit a dead end, I continued on the original path and used FlashTool to flash 14.2.A.1.114_Customized firmware (why this - because it was the only full firmware that I found). Anyway, thankfully, I now have a working device running that firmware with Android 4.3. I'll try and proceed to get back up to date.

devo1d said:
(why this - because it was the only full firmware that I found).
Click to expand...
Click to collapse
Not sure how when this thread is stickied at the top of the General Section. Z1 Compact Resource Thread -|-Rooting-BL Unlocking-Firmware & More..

Oh my goodness......... It is pantomime season after all

Magic. I confess to being another dizzy head when things don't go right and reading from a multiple sources and getting a bit overwhelmed & lost. Anyway, found the way out and thank you for the pointer to the sticky right-in-front-of-the-eyes info. Bookmarked.

Soft Bricked - Unable to Sideload OTA

Hi all,
My Nexus 5x (16gb - all stock.) went and soft bricked today. Not sure why - just seemed to start wanting to constantly restart - never making it past the white google text part of the boot process. Not sure if it's an update or hardware. No trauma or dropping of the phone - which makes me think s/w rather than h/w.
I have attempted to install a rescue OTA update (instructions I followed are from technobill - don't have enough posts to add a link). However, when running "adb sideload <file>" I get a "failed to read command" error. Have tired multiple cables/ports however to no avail.
(Recovery screen shows the following build details: 7.0/NBD90W/3239497)
Any ideas?
Thanks.
Somewhat Irked

SomewhatIrked said:
Hi all,
My Nexus 5x (16gb - all stock.) went and soft bricked today. Not sure why - just seemed to start wanting to constantly restart - never making it past the white google text part of the boot process. Not sure if it's an update or hardware. No trauma or dropping of the phone - which makes me think s/w rather than h/w.
I have attempted to install a rescue OTA update (instructions I followed are from technobill - don't have enough posts to add a link). However, when running "adb sideload <file>" I get a "failed to read command" error. Have tired multiple cables/ports however to no avail.
(Recovery screen shows the following build details: 7.0/NBD90W/3239497)
Any ideas?
Thanks.
Somewhat Irked
Click to expand...
Click to collapse
Did your phone just reboot in the middle of doing something innocuous then start bootlooping? Were/Are you on total stock with bootloader locked? If both yes, it is probably hardware issue you are encountering.
Regarding sideloading, did you place your Android recovery in sideload mode?
Did you verify adb can "see" your device using "adb devices"?

SomewhatIrked said:
Hi all,
My Nexus 5x (16gb - all stock.) went and soft bricked today. Not sure why - just seemed to start wanting to constantly restart - never making it past the white google text part of the boot process. Not sure if it's an update or hardware. No trauma or dropping of the phone - which makes me think s/w rather than h/w.
I have attempted to install a rescue OTA update (instructions I followed are from technobill - don't have enough posts to add a link). However, when running "adb sideload <file>" I get a "failed to read command" error. Have tired multiple cables/ports however to no avail.
(Recovery screen shows the following build details: 7.0/NBD90W/3239497)
Any ideas?
Thanks.
Somewhat Irked
Click to expand...
Click to collapse
Well luckily I made this post today.

The more this goes on, the more I believe it to be hardware ...
@sfhub - reasonably innocuous. Had just opened one or 2 apps that morning. Not sure what had updated overnight app/os wise. Not anything interesting as far as I can tell. Once I managed to get it into recovery "adb devices" was returning the phone.
@bardhi92 - I saw that once I got in. However, I couldn't get it to see my phone.
Updated things I have tried and why I've all but thrown in the towel:
After the OTA rescue sideload failed I started trying a few different things. It stopped taking me into recovery mode more frequently, at least it seemed that way - it would just keep bootlooping. My main issue is that I has a locked bootloader, which stopped me whacking TWRP on and loading on a custom rom - just to see if that worked.
I thought it might let me sideload on a factory default img file. Turns out nope.
However I used NRT to "Flash Stock + Unroot" (with "Soft Brick/Bootloop" checked) which for some reason, then allowed me to get back into recovery mode. I had also removed the sim card/tray at this point. May have been either or neither of those that allowed me to get into recovery mode. Can't say for certain.
I cleared /cache and /data and then attempted the OTA rescue update again. This time it failed at 45% (according to my cmd prmpt) with the error: "* failed to read command: No error". I'm not sure text was on the phone at the time. But it did manage to boot into Android. I quickly stepped through the various intro steps (putting in the sim, adding my mail google account details).
I went to get a beer. Only to find it boot looping again.
Not to be deterred, I vowed to try again. Same steps as before (remove sim, nrt voodoo). This time however the OTA rescue worked and fully completed. I went through the intro steps again. This time I quickly turned on dev options, enabled usb debugging and sorted out the OEM bootloader. I thought this would be smart, just in case it hapened again. Once I chose to unlock ("fastboot reboot", selected yes), it decided to start boot looping again.
The main annoyance is: I don't think I have any proof of purchase, even though it's in warranty. That, and I now live in Dubai - so shipping back to the UK where I brought it is going to be killer. But I think it's the path of least resistance at the moment.

SomewhatIrked said:
The more this goes on, the more I believe it to be hardware ...
@sfhub - reasonably innocuous. Had just opened one or 2 apps that morning. Not sure what had updated overnight app/os wise. Not anything interesting as far as I can tell. Once I managed to get it into recovery "adb devices" was returning the phone.
@bardhi92 - I saw that once I got in. However, I couldn't get it to see my phone.
Updated things I have tried and why I've all but thrown in the towel:
After the OTA rescue sideload failed I started trying a few different things. It stopped taking me into recovery mode more frequently, at least it seemed that way - it would just keep bootlooping. My main issue is that I has a locked bootloader, which stopped me whacking TWRP on and loading on a custom rom - just to see if that worked.
I thought it might let me sideload on a factory default img file. Turns out nope.
However I used NRT to "Flash Stock + Unroot" (with "Soft Brick/Bootloop" checked) which for some reason, then allowed me to get back into recovery mode. I had also removed the sim card/tray at this point. May have been either or neither of those that allowed me to get into recovery mode. Can't say for certain.
I cleared /cache and /data and then attempted the OTA rescue update again. This time it failed at 45% (according to my cmd prmpt) with the error: "* failed to read command: No error". I'm not sure text was on the phone at the time. But it did manage to boot into Android. I quickly stepped through the various intro steps (putting in the sim, adding my mail google account details).
I went to get a beer. Only to find it boot looping again.
Not to be deterred, I vowed to try again. Same steps as before (remove sim, nrt voodoo). This time however the OTA rescue worked and fully completed. I went through the intro steps again. This time I quickly turned on dev options, enabled usb debugging and sorted out the OEM bootloader. I thought this would be smart, just in case it hapened again. Once I chose to unlock ("fastboot reboot", selected yes), it decided to start boot looping again.
The main annoyance is: I don't think I have any proof of purchase, even though it's in warranty. That, and I now live in Dubai - so shipping back to the UK where I brought it is going to be killer. But I think it's the path of least resistance at the moment.
Click to expand...
Click to collapse
So, you flashed the .TOT file, sideloaded the given OTA within the stock recovery bootloader that comes with the .TOT file, and cleared cache/factory reset?
Please condense it. If you managed to start up the phone, that's a huge success for people who have not been able to yet.

bardhi92 said:
So, you flashed the .TOT file, sideloaded the given OTA within the stock recovery bootloader that comes with the .TOT file, and cleared cache/factory reset?
Please condense it. If you managed to start up the phone, that's a huge success for people who have not been able to yet.
Click to expand...
Click to collapse
In short:
OTA rescue failed during adb sideload,
Tried bullhead-nbd90w-factory-d2f11c5f.zip & removed sim tray - seemed to allow access to recovery mode,
OTA rescue claims to have failed at 47% during adb sideload- still booted into android. However briefly. Went back to bootloop,
Tried bullhead-nbd90w-factory-d2f11c5f.zip & removed sim tray - seemed to allow access to recovery mode,
OTA rescue completed via adb sideload,
Turned on dev options (usb debug, oem unlock),
Booted to fastboot - unlocked bootloader. Now back to bootlooping
@bardhi92 - I could not get the LG utility to detect my phone. Will attempt again tomorrow.

SomewhatIrked said:
@bardhi92 - I could not get the LG utility to detect my phone. Will attempt again tomorrow.
Click to expand...
Click to collapse
IMO you shouldn't flash the TOT file. If you end up bootlooping again, your phone will be stuck in bootloader locked mode with no ability to unlock it.
If you were able to get your phone to boot into android once, there is really nothing the TOT file will do for you that you can't do from TWRP or bootloader, whereas once it locks your bootloader, there are problems you can no longer fix like EFS corruption (which likely isn't your problem).
In the end, you probably do have eMMC that is slowly starting to fail. There is usually error correction on the eMMC that can lock out bad blocks but if it gets to serious, it'll fail. This is why reflashing stuff over and over sometimes works.

Stuck in setup wizard after factory reset

Alright, hello everyone,
I'm having a pretty weird issue here. I've flashed my DUK-L09 and the C432B183 EU Firmware, everything was running fine.
I couldn't make a backup of the /data/ partition though, someone told me to wipe the data to decrypt it, but nothing came good after this.
So I tried to flash back the old recovery image by extracting it, flashing it via fastboot, as I would normally do; enter the factory reset, run it.
Everything is good, it goes up to 100% pretty fast, less than 2 minutes. I then enter the setup wizard the NFC is acting weird. It keeps activating
and deactivating illogically. So, ignoring this issue, I kept up configuring the phone then once I'm logged in Google and sync'd, pops a Huawei ID
logging page really really fast then goes back to the EMUI menu at the beginning of the Setup, in an infinite loop.
Useful information to let you help me better:
- Many firmwares. Currently trying to flash back to B120a and NoCheck from OldDroid and Morph. (Edit: Didn't work)
- Phone unlocked, TWRP accessible.
- Getting a weird "Error 9" when trying to run Update.zip from TWRP.
- Sideload working, but not transferring anything.
- Cannot find any B182 or B130 stock firmware. Everything seems to be gone from Huawei's servers.
- The loading logo isn't Honor anymore but Android, for a reason I can't yet understand.
- Restoring a clean backup (without /data/, since I couldn't back it up) did not fix the problem.
- Trying to update with the 3 buttons do not work, even with the right firmware (C432B183) (Software install failed)
- Factory reset works with the right ROM, but gets me to the setup loop issue.
- The loop occurs when I am supposed to see the Huawei ID setup page. If I do not put any SIM card, or WiFi
I am prompted to choose which way to restore data; if I skip this step, it blinks and doesn't do anything.
- I tried to restore via WiFi (Google's cloud stored data from my account), but it does the same thing as mentioned
earlier. It blinks multiple times rapidly the "Huawei ID" setup page then goes back to the first Setup screen w/o
me being able to do anything about that.
I'll be glad if you knew the answer to this, because I'm all lost right now.
Greetings, Kameyuu.

UP !
After many tries and a LOT of hard work, and spent an entire night (was about to spend the second night on this), I found the culprit and now I know what the issue is, it sounds completely legitimate.
So here are the reason and the solution to this issue:
Actually, my CUST was somehow broken. I never flashed it back because no one told me to flash the CUST.img back. They told me to flash BOOT, SYSTEM, and RECOVERY only.
So, after I downloaded a software called HUAWEI Multi-Tool (From hwmt.ru) I noticed they were also asking for the CUST.img and USERDATA.img (<- this one was apparently optional)
So, trying my luck I flashed it. Did a factory reset, and all, it acted weird and failed, then I tried again and it succeeded. So, with all my hope I booted the phone to the system, started configuring... And it worked !
I was able to set up the phone. For a -yet- unknown reason, some apps look missing and the NFC is still blinking on and off repeatedly and randomly, but I'm investigating that.
If you have any question on the precise steps feel free to send me a PM or ask in the thread directly I'll be glad to sort your issue out.

[EDIT]
Sorry, double post I don't know why my message was posted twice. Feel free to delete this message @moderators

Huawei P10 Lite Rescue...

Hi guys,
i am trying to rescue my P10 lite after some bobo happened. I am hoping for getting some experts on leading me to the right path, delivering as much as possible background in the following lines.
Setup of my device:
- Huawei P10 Lite
-WAS-LX1A
-Firmware: WAS-LX1AC652B101 (DC Unlocker Information)
What (i guess) went wrong:
-I tried to SD-software upgrade my phone but obviously i used wrong firmware -or- some other issue during the update occured. I realized during update process that the phone restarted without it was finished (somewhere at ~50%)
-Now i can't boot, ending up with all same loops as further described
-Immediately after start of phone, i see Huawei logo and then following error message: ERROR MODE: Attention! Please update system again. Error Error NO: 11 (recovery image) & Error NO: 2 (load failed), each start ends up here.
-Recovery can't be entered, hard-reset didnt work
-Fastboot entering and sending commands is possible but with (Phone Locked, FRP Lock message) this somehow keeps me limited to what i can do?
What did i try so far to rescue:
-Apart from above obvious (fastboot/hard-reset/let battery go empty and try recharging again)
-Tried using DC-Unlocker to access some more info, didnt spend credits as i read to many bad experiences not leading to success
Desired outcome:
-I want to bring life back to the phone, no matter in what way either as stock ROM (best case) or certain custom ROMs i dont mind, as long as it usable again. In best case scenario not paying for it without guarantee to success (like DC unlocker etc.)
Do you guys can please shed some lights with a complete sad moron as i am
PS. i must say that i can do a lot of technical stuff on PC, but with android and especially with Huawei i am a complete noob, so if you refer me to some software or firmware please share link if possible? Otherwise i will of course try to find the appropiate with the hints coming from here.

[Help] Stock S9 stuck in bootloop

SOLVED - Update below.
Hey guys,
I have an S9 (SM-G960F) which appears to have auto-updated during the night and as a result will now not boot. I am making an assumption it was an update of some sort as when I checked the time on it at 1am it was fine, when I woke around 8.30am the phone was off and when powering it on I ran into the issue. To summarise, I power the device on, get the Samsung loading screen, then the black swipe pattern screen to decrypt the phone, followed by the padlock unlocking loading screen, then the phone reboots. Sometimes however, the device gets past the padlock loading screen and says it is optimising apps, which is then followed by a reboot, briefly says it is installing system update before landing me at the Android Recovery screen.
What I've tried:
- Soft reset
- Booting in safe mode (same result as booting normally)
- Clearing cache partition
- Clearing app data
- Lacking storage booting (the device was quite low on storage last time I checked)
Some other (maybe) useful info:
I haven't updated the phone for months, could be why it did an auto update.
I'm on EE in the UK but IIRC the phone is not locked to EE.
Android Recovery has the following info when I load into it
Code:
samsung/starltexx/starlte
9/PPR1.180610.011/G960FXXU2CSB9
(options to try again, erase app data, power off, view rescue log)
#Reboot Recovery Cause is [system_server:12259 RecoverySystemRescueParty]#
Support SINGLE-SKU
Block-Based OTA
Supported API: 3
Viewing the rescue log presents me with a stacktrace , the top of which is
Code:
*** FATAL EXCEPTION IN SYSTEM PROCESS: main
java.lang.RuntimeException: Failed to create service com.android.server.job.JobSchedulerService: service constructor threw an exception
(followed by the rest of the stacktrace I can get a picture of if necessary)
My goal here is to recover the photos on the internal storage as they don't appear to be backed up to Google photos, nor Samsung's alternative - which is particularly painful cause I'm the one usually preaching backups.
Is there anyway to recover the OS to retrieve data, or pull the data off the device without wiping it? I'm open to any suggestions on how to do this, the main goal here is saving my photos, hence why I have avoided a factory reset from the Android Recovery menu.
Hope I've been clear enough, but let me know if I need to clarify anything. I would greatly appreciate any suggestions!
Thanks,
Matt

Hey guys,
After spending all day tearing my hair out with this I managed to fix it, so I guess this thread can be closed. For anyone who gets into a similar situation...
I attempted to solve this by flashing the current firmware using Odin and booting into "download mode", found a copy on sammobile.com. This didn't work, leaving me in the same situation, and as I felt I was running out of options I tried using the latest firmware for my device. I found a copy using a tool I found on these forums - Frija. Fired up Odin and download mode again, selected the AP/BL/CP/HOME_CSC (I understand using HOME_CSC is important so as not to cause a factory reset) and this worked! This left all of my files intact and as a bonus I'm also up-to-date with Android too. I'm backing up my photos as we speak as I would hate to be in this situation again!
Hope that can help someone in the future.
Cheers,
Matt

Which version of Odin did you use?

majormatt said:
Hey guys,
After spending all day tearing my hair out with this I managed to fix it, so I guess this thread can be closed. For anyone who gets into a similar situation...
I attempted to solve this by flashing the current firmware using Odin and booting into "download mode", found a copy on sammobile.com. This didn't work, leaving me in the same situation, and as I felt I was running out of options I tried using the latest firmware for my device. I found a copy using a tool I found on these forums - Frija. Fired up Odin and download mode again, selected the AP/BL/CP/HOME_CSC (I understand using HOME_CSC is important so as not to cause a factory reset) and this worked! This left all of my files intact and as a bonus I'm also up-to-date with Android too. I'm backing up my photos as we speak as I would hate to be in this situation again!
Hope that can help someone in the future.
Cheers,
Matt
Click to expand...
Click to collapse
I would really appreciate it if you post a YouTube tutorial on how to fix this. Because we are facing the same problem right now but I have no idea what solution you prescribed. Thank you and God bless.