Since about 2 weeks my phone had a problem with its micro-usb port, because it was thinking that it was charging without even a usb cable in it. I searched the forum and found out that i should replace the micro usb ribbon cable. Well today i did that and the charging problem is solved.
But when i was disassembling my phone i accidently broke the volume button flex cable . And now my volume buttons dont work any more, i went to ebay and bought the volume ribbon cable for my nexus and i will get it around next week. But does anyone know if its just like the micro-usb ribbon cable that you just have to click it in? Or does it have to be soldered? Because if it has to be soldered i have a big problem because i have no clue of how to do that :s.
Thanks in advance
My phone is a GSM (i9250) version by the way.
If you have the GSM version, it's just a cable you "click in", however on the CDMA versions, the volume buttons are soldered to the motherboard.
Gforce083 said:
If you have the GSM version, it's just a cable you "click in", however on the CDMA versions, the volume buttons are soldered to the motherboard.
Click to expand...
Click to collapse
I found an immage on the internet and it is of the GSM version but i can't post url's .
it looks on that pic as if it is soldered on, it has 3 metal pins on the cable. so my guess its soldered on then, no? or can you please show me a gsm version pic where you can tell me if its soldered on or just clicked in
Sorry to rain on your parade brother, the volume flex ribbon cable absolutely needs soldered on, the POWER button flex cable however does not. Simply undo the little black clip and pullout the old ribbon, slide the new power button flex cable in and flip the plastic clip back down and you're good to go. I know this because I just replaced both on my phone.
In the attached image, look near the red outlined box toward the top, it's the RFMD RF6260 quadband 2g/3g/4g power amplifier module (again, outlined in red), you'll see the longer skinny flex cable with double sided sticky tape. Look closely, that bastard is soldered on there, 3 pins.
USMC0341 said:
Sorry to rain on your parade brother, the volume flex ribbon cable absolutely needs soldered on, the POWER button flex cable however does not. Simply undo the little black clip and pullout the old ribbon, slide the new power button flex cable in and flip the plastic clip back down and you're good to go. I know this because I just replaced both on my phone.
In the attached image, look near the red outlined box toward the top, it's the RFMD RF6260 quadband 2g/3g/4g power amplifier module (again, outlined in red), you'll see the longer skinny flex cable with double sided sticky tape. Look closely, that bastard is soldered on there, 3 pins.
Click to expand...
Click to collapse
Ok thanks, i will have to let it get fixed by someone then
haris2030 said:
Since about 2 weeks my phone had a problem with its micro-usb port, because it was thinking that it was charging without even a usb cable in it. I searched the forum and found out that i should replace the micro usb ribbon cable. Well today i did that and the charging problem is solved.
But when i was disassembling my phone i accidently broke the volume button flex cable . And now my volume buttons dont work any more, i went to ebay and bought the volume ribbon cable for my nexus and i will get it around next week. But does anyone know if its just like the micro-usb ribbon cable that you just have to click it in? Or does it have to be soldered? Because if it has to be soldered i have a big problem because i have no clue of how to do that :s.
Thanks in advance
My phone is a GSM (i9250) version by the way.
Click to expand...
Click to collapse
same happen to me how did you get it fix?? please respond.
Has anyone been able to fix this? I just ordered a solder kit. 50/50 chance I'll screw this up.
zmattmanz said:
Has anyone been able to fix this? I just ordered a solder kit. 50/50 chance I'll screw this up.
Click to expand...
Click to collapse
Which solder kit did you order?
I have to replace my volume ribbon cable. I have the replacement. I need to buy a solder gun.
What should I do?
There's no way I can afford a new motherboard, and it seems impossible to remove the power button flex for replacement without instructions, re-attaching a new one would be fairly easy I imagine, but I desperately need help for this one.
Are you absolutely sure you've broken it? Did you fix it? I have seen a couple devices where the flex cable pops out of its connector (especially if you go disassembling the device) but ever so slightly that the power button works only sporadically. The fix seems to be to reconnect the flex cable and the power button starts working.
torn power cable!!
ShadowOfScales said:
What should I do?
There's no way I can afford a new motherboard, and it seems impossible to remove the power button flex for replacement without instructions, re-attaching a new one would be fairly easy I imagine, but I desperately need help for this one.
Click to expand...
Click to collapse
I have replaced smashed screens and uodated the battery, then after I needed to hotwire the battery so I could finish flashing a ROM, I have carelessly managed to slightly tear the power ribbon up near the switch button. GRRRRR
I am about to attempt to drop a slither of solder across a slit I'll make with an exacto knife and see if I can get anything. It will power on as I added a switch in the NiMH battery pack I made up and was surprised that I couldn't make any selections while I was doing stuff in the bootloader functions. Bugger. I mabaged to relock the bootloader as I was going stock for something, then after power drain (I now realise that it doesn't charge your phone while in the bootloader screen) and now with a re-locked bootloader, I cannot select 'yes' to unlock the bootloader again suggestions? ...meanwhile, I'm about to probably waste my time attempting McGyver ribbon cable surgury.
I did actually manage to repair a ribbon cable using enamelled wire (30 awg) and a microscope but eventually just replaced the cable.
I bought a cable similar to the one you want for approx £5 which arrived 2 days later.
The on off switch and the other end are just held on with 2 sided tape, so will gently peel off by prying beneath them. I did think the other end would not come off.
My advice replace the cable.
Hey guys so I'm kinda starting a project. would love some help, so my Optimus got screwed up a ways back and the accelerometer and light sensor got screwed up. so I found another on with a broken screen on it and swapped the motherboard to make a 100% working one. I want to use the old one on a tv, like find a usb to hdmi and use the phone on a tv and get a Bluetooth keyboard. problem is, the phone wont power up without a battery in it. Does anyone know of a trick that I can plug the phone into usb power and power it up with no battery?
Hello guys,
I have replaced my battery today, but it seems as I was struggling to remove the glue I have ripped the side buttons ribbon cable a little, therefore the power button is not working and I can't power on the device.
When I plug it in a computer, I can see it charging. In device manager it is showing up as DVD Device - HTC Android Phone USB Device and as a USB Mass Storage Device. I have tried fastboot and adb and they are not responding.
I only want to power on the device, so I can use it, because for a new cable to arrive it will take like two months.
Any help is appreciated.
Thank you in advance.
EDIT: This is the part where it got ripped.
As I was looking for a cable from ebay, I noticed something. The cable there on the bending has only one track!
The first thing I immediately tried was touching the two parts of the cable to try to reconnect it, so I can at least power the phone on, but it didn't work.
What I was also thinking is to put some kind of conductor between the rippage, but I thought there were more than one path on the circuit and that I can put electricity where I don't want it.
Now, looking at this one circuit path do you think putting a solder wire in between could transfer the power up signal? Or is it not a good idea? Is it possible that there are more connections inside beside that track?
P.S: I am not a very good electrician, I have soldered some pins, but I really have no deep knowledge in that area.
EDIT: I have fixed this by buying a new module from ebay and replacing it.
Hi guys,
I recently tried to replace a cracked screen and encountered more problems i need to fix.
1) front selfie camera isnt Working. I think i accidentally ripped the ribbon cable at the corner. Is this salvagable? I cant find any replacement parts for this either.
https://photos.app.goo.gl/AxUSUdxttbST9oKw5
2) i cant seem to plug in the black and white signal cables in the mothboard back in. I get the feeling i've pulled out the port when i took them out and now can't put them in. Could I solder these parts in? What are these signal cables used for?
https://photos.app.goo.gl/H2eBenenF8Akp8Fa6
I'm extremely grateful for your support!