Related
Important The below codes are not for noobs. If you by-chance brick your phone. I am no-where responsible. You can regain your firmware by flashing it to the phone. That is no Problem
Note-P.S- All the codes can be entered using the dialer...The code will be executed after you enter the last # ( i.e. if you just enter the codes below, it will execute it without permission
*2767*3855#
Think twice before you use this code. It is a Factory reset code. This will wipe off all your data be it in the internal memory or the external memory. I advice you people to use this code with the External SD card and the SIM removed.
Once you have entered this code, There is no way you can stop it.
*#197328640#- This code is used to enter the Service mode. You can change settings here and run some tests. Any changes except for the camera part will no crash your FW.
*#0228#- This code gives you information about your phone battery.
*#7465625#- This code can be used to check the status of SIM lock, Network LOCK,etc.
Codes to get Firmware Version Information
*#4986*2650468# - SW Version, HW Version, MP, RF Cal Date, CSC Version, CSC Model Spec, FFS Version, RC2 Version
*#1234# - SW Version and CSC Version
*#1111# - FTA SW Version
*#2222# - FTA HW Version
Wi-Fi and Bluetooth testing codes
*#526# - Wi-Fi Manual MFG Test Mode
*#232337# - BT RF Test Mode
Code to launch various factory tests
*#0*# - LCD test
*#0673# OR *#0289# - Melody test
*#0842# - Vibration test
*#2663# OR *#2664# - TM Command
*#4097*4097# - GPS menu
*#272*time* - csc pre configuration
example *#272*1423* ( if the time is 14:23)
*#0002*28346# - Another service menu
*#0228#- Battery test
*#232337#- Bluetooth addrs
*#5239870*# - Admin settings
*#66225*# Motion Calibration
PS- Many users have complained that the motion sensor calibration code is resulting in the incorrect functioning of the Accelerometer. If you encounter such a problem or if you want to use the Motion sensor Calibration code, Please be sure to place the phone on a flat surface and wait for about a minute!
And tell me how you like it!
Nice post. The code for the battery is very helpful, since I cannot find an app that displays the percentage, like in android.
emiok said:
Nice post. The code for the battery is very helpful, since I cannot find an app that displays the percentage, like in android.
Click to expand...
Click to collapse
.. Settings - About your phone (or Info .. I don't know how is write in English) - System Info - Battery ...
Fahrenheit51 said:
.. Settings - About your phone (or Info .. I don't know how is write in English) - System Info - Battery ...
Click to expand...
Click to collapse
Ya.. but i don't think it is so informative..As mentioned, it is like the battery info on Android Settings...!!
*#0*# = full test menu
*#272*time* = csc pre configuration
example *#272*1423* ( if the time is 14:23)
roxyroot said:
Ya.. but i don't think it is so informative..As mentioned, it is like the battery info on Android Settings...!!
Click to expand...
Click to collapse
what do you mean? I shows me about 73% and bada under settings tell me 74% maybe its uprounded...
And what is the real data? Bat RAW SOC or BAT adjusted SOC?
Thx to op for this thread...
Very useful, thanks!
Dont forget the gps menu -
*#4097*4097#
edit : this does not work in BADA 2.0.1
The bada 2.0 equivelent is *#3214789650# (for versions prior to PKH2 this needs the phone in MID debug level)
Samuel Sung said:
what do you mean? I shows me about 73% and bada under settings tell me 74% maybe its uprounded...
And what is the real data? Bat RAW SOC or BAT adjusted SOC?
Thx to op for this thread...
Click to expand...
Click to collapse
adjusted SOC
duxxyuk said:
Dont forget the gps menu -
*#4097*4097#
Click to expand...
Click to collapse
Man! Thanks for reminding! I wrote it down..But forgot to put it on!
roxyroot said:
Man! Thanks for reminding! I wrote it down..But forgot to put it on!
Click to expand...
Click to collapse
Heh, if you want to live dangerously (newbies - stay WELL CLEAR) it's possible with certain firmwares to unlock the master debug mode :
Unlock debug by dialing *#33284*# then choosing mid or high. The phone will then reboot.
It is now possible to dial up the debug menu by dialing *#7092463*#
Do be aware that the debug modes will slow down your phone as this activates a second serial port to which loads of information is being dumped... I's been very useful for the bootloader work.
All the best ~D
duxxyuk said:
Heh, if you want to live dangerously (newbies - stay WELL CLEAR) it's possible with certain firmwares to unlock the master debug mode :
Unlock debug by dialing *#33284*# then choosing mid or high. The phone will then reboot.
It is now possible to dial up the debug menu by dialing *#7092463*#
Do be aware that the debug modes will slow down your phone as this activates a second serial port to which loads of information is being dumped... I's been very useful for the bootloader work.
All the best ~D
Click to expand...
Click to collapse
i didn't know that! ( It is not the Nat Geo show!)
*#66225*# Motion Calibration
sitcoms said:
*#66225*# Motion Calibration
Click to expand...
Click to collapse
Woah, that's the one that had me RE-calibrating my phone whilst holding it at 45° to the right with the top touching the floor and the bottom about 2cm's off the floor .
If your accelerometer works... DON'T fix it
^
just put the phone on a flat surface then calibrate it
sitcoms said:
^
just put the phone on a flat surface then calibrate it
Click to expand...
Click to collapse
This doesn't work at all times if the sensor itself is not placed properly in the device. I too had to calibrate it with the phone at odd angles to perfect the sensor. Now the accelerometer works absolutely fine.
After changing files with sTune should i send *2767*3855# for factory reset? Is this correct? Thanks!
Thanks man! You rock! Wanted some of these!!
@Gremo What files are you changing and why? If you want the hard reset, just go to the dialer and type "*2767*3855#", it will conduct the reset automatically!
@dancegirl You are welcome!
Hi all, the most of the known Bada 2.0 Mobile Codes are invalid on 8600
If anyone knows some for S8600, pls post.
It could be helpful for owners of this device.
Thanks
*#197328640# should run
*#7092463*# seems to run without higher Debug Level then Low
Otherwise *#33284*# for Debug Level change...
More for advanced users, but same like S8500/S8530 use. So take an look here first:
http://forum.xda-developers.com/showthread.php?t=1154945
Best Regards
adfree said:
*#197328640# should run Does not work
*#7092463*# seems to run without higher Debug Level then Low
Click to expand...
Click to collapse
Did not try the others when I try the Wave III.
*#197328640# should run Does not work
Click to expand...
Click to collapse
Please see here:
http://forum.xda-developers.com/showpost.php?p=19687534&postcount=22
Okidoki...
Mabye we should write which Firmware Version we have tried...
Maybe there are big difference between prototype Firmware... and now Retail...
Thanx in advance.
Maybe also usefull, write Code which not work on your S8600... So other S8600 user can confirm or not...
Maybe again protected by Debug Level... like Internal Menu... *#709blabla...
Best Regards
This Codes are working:
*#0228#- Battery test
*#272*time* - csc pre configuration
example *#272*1423* ( if the time is 14:23)
*#0*# - LCD test
*#526# - Wi-Fi Manual MFG Test Mode
*#1234# - SW Version and CSC Version
*#7465625#- This code can be used to check the status of SIM lock, Network LOCK,etc.
Phone INFO ★Samsung★ - all key info: CSC, Bootloader, Secret Codes, Country of Origin
This app will show you:
- CSC code, CSC country. And also allow you to change the CSC.
- Bootloader version, Baseband version, PDA version...
- All Secret Codes in your phone (more than 170 secret codes)
- Country of Origin, Manufacturing date, phone color...
- Usage history: Headset Connect Counter, Charger Connect Counter
And more info are available.
Play Store: https://play.google.com/store/apps/details?id=org.vndnguyen.phoneinfo
New update v2.6.0:
- Update CSC Lookup database.
- Update for the Firmware Browser due to sammobile.com has changed its page format.
New Update v3.0.0:
- Completely new Material Design UI.
- Multi-language support (currently only English and Vietnamese)
- Added new Settings menu.
- Improved Samsung S/N and IMEI analysing tools.
And a lot of improvements and bug-fixes.
Nice
Using on my edge now
Would anyone please send me some screenshots from the main screen of the app (GENERAL / CSC CODE / FIRMWARE / ...).
I really need these info. Thank you.
One second
Here you are
ktetreault14 said:
Here you are
Click to expand...
Click to collapse
Thank you so much, ktetreault14.
vndnguyen said:
Thank you so much, ktetreault14.
Click to expand...
Click to collapse
Just trying to help out as much I can.
ktetreault14 said:
Just trying to help out as much I can.
Click to expand...
Click to collapse
Could you also try the 'Refurbishment Check' function in the menu?
Thanks
vndnguyen said:
Could you also try the 'Refurbishment Check' function in the menu?
Thanks
Click to expand...
Click to collapse
Sure
vndnguyen said:
Could you also try the 'Refurbishment Check' function in the menu?
Thanks
Click to expand...
Click to collapse
There we are
BIG Thanks.
vndnguyen said:
BIG Thanks.
Click to expand...
Click to collapse
Anytime
New UPDATE v3.2.0:
- Added theme options (Dark or Light).
- Added new languages:
العربية (Arabic)
Deutsch (German)
français (French)
italiano (Italian)
עברית (Hebrew)
português (Portuguese)
română (Romanian)
русский (Russian)
shqip (Albanian)
中文 (Chinese)
- And a lot of bug fixes and improvements.
Enjoy.
Update v3.2.5:
- Added Screen Density info (DPI).
- Added Türkçe (Turkish) language.
- Improved the Dark theme, fixed some UI issues.
- Fixed some translation errors.
Enjoy.
thanks for the app, looks great.
One thing, i can't get any of the tools inside other tools working. Specifically i'm wanting to change my csc but when clicking on csc selector and verifier i get multiple java errors. Is this a broken feature on the S6 for now?
v3.2.5 not working
dazbutler1 said:
thanks for the app, looks great.
One thing, i can't get any of the tools inside other tools working. Specifically i'm wanting to change my csc but when clicking on csc selector and verifier i get multiple java errors. Is this a broken feature on the S6 for now?
Click to expand...
Click to collapse
Same error for me here too! On a G920F I cannot access the CSC Selector and CSC Verifier due to multiple Java errors.
dazbutler1 said:
thanks for the app, looks great.
One thing, i can't get any of the tools inside other tools working. Specifically i'm wanting to change my csc but when clicking on csc selector and verifier i get multiple java errors. Is this a broken feature on the S6 for now?
Click to expand...
Click to collapse
dehnhaide said:
Same error for me here too! On a G920F I cannot access the CSC Selector and CSC Verifier due to multiple Java errors.
Click to expand...
Click to collapse
Yes, it is the known issue since the firmware version 1BOB7 on Galaxy S5. And the S6/S6 Edge may be on the same boat.
Currently there is still no workaround for it. If I'll find one, I will fix it soon.
Thanks for choosing my app.
Hey mates,
my XZ1c (unlocked) just received the new OTA in Germany, security patch level October 1st.
Anyone an idea what has changed? There is no official changelog or at least I didn't find any
Hello.
I got it too.
No change log on the notification, so i do not know too.
BlueBorne vulnerability fixed
I can confirm BlueBorne vulnerability fix too. No news on camera fix :/ BTW Can we use somehow the BlueBorne vulnerability to root XZ1C? Or to backup TA partition (DRM keys)?
Good question...
Davka said:
BlueBorne vulnerability fixed
Click to expand...
Click to collapse
Yeah, but for that only the update didn't need 300MB I guess
Camera "distortion" (mind the quotes) is unchanged.
Anybody using a VPN to get this update? Because I just tried VPN locations in Germany, Japan, and Austria with no luck on getting the new OTA.
I think that would not work, it's based on the emei and rom canal on the phone, so using a vpn will not change anything.
If you are on a USA model, and that the update is not released yet for the USA version, changing for EU country will not change anything.
And even if it's released for usa, it could be a little bit later for your phone, as sometimes they restricted to some IMEI not to push on all the phone in the same time.
Just updated. Don't feel any different compare to .324 aside from october security update.
Sent from my XZ1 Compact using XDA Labs
3 new things I notice after using this firmware for 1-2 days:
1) The login process to google account with 2-steps verification activated is hassle free now. In previous firmware I had trouble getting and entering the verification code, and thus had to manually disable the 2-step verification before I could login.
2) Maybe placebo, but I feel I get a better and more stable mobile data connection. Previously it felt like even though the mobile data was active and the icon shows connected to 3G, but occationally I couldn't do anything related to internet connection until I turn off and on again the mobile data. Maybe it was due to bad signal from provider on that day too, I don't know.
3) Very minor adjustment; when we press the volume up/down button it used to show 'ring volume', but its now 'ring and notification volume'.
Still no update for my phone Is has a china IMEI. Maybe i just have to wait.
What's different in the firmware update..
I did an extract and compare against the UK 324 and 374 versions and came up with a rough list.
The contents of these SIN files are exactly the same:
adspso_X-FLASH-ALL-C93B.sin
amss_fs_1_X-FLASH-ALL-C93B.sin
amss_fs_2_X-FLASH-ALL-C93B.sin
appslog_X-FLASH-ALL-C93B.sin
bluetooth_X-FLASH-ALL-C93B.sin
bootloader_X_BOOT_MSM8998_LA1_1_O_77_X-FLASH-ALL-C93B.sin (all boot SINs, actually, but this is the one that gets loaded)
cache_X-FLASH-ALL-C93B.sin
diag_X-FLASH-ALL-C93B.sin
fsmetadata_X-FLASH-ALL-C93B.sin
ramdump_X-FLASH-ALL-C93B.sin
ssd_X-FLASH-ALL-C93B.sin
persist_X-FLASH-ALL-C93B.sin
Qnovo_X-FLASH-ALL-C93B.sin
userdata_X-FLASH-ALL-C93B.sin
All *.ta files are the same.
Now for the differences.
amss_fsg_X-FLASH-ALL-C93B.sin:
MCC 240 was moved from the [mcc_list name="eu_b4_mccs"] config to a new [mcc_list name="swe_mccs"] config.
elabel-G8441-row-row_201709190503668.1_47.1.A.2.374_X-FLASH-LTALABEL-C93B.sin:
Added a regulatory label for Malaysia.
fotakernel_X-FLASH-ALL-C93B.sin (Ramdisk only, didn't extract the kernel):
crashtag specifies new firmware version
sepolicy bits changed
prop.default has "ro.setupwizard.rotation_locked=false" added
kernel_X-FLASH-ALL-C93B.sin (Ramdisk only, didn't extract the kernel):
crashtag specifies new firmware version
sepolicy bits changed
init.sony-platform.rc had this line removed: setprop persist.bluetooth.btsnooppath "/sdcard/btsnoop_hci.log"
modem_X-FLASH-ALL-C93B.sin:
Changed audio, modem, qdsp6m, and sensor blobs
oem_X-FLASH-ALL-C93B.sin:
"ssid=_The Cloud X" added to preset_networks.conf
APN updates
"com.amazon.avod.thirdpartyclient.apk" added
ee_ims & telefonica specific modem configs added
Overlay APK changes (I didn't check the changes)
Version & region changes (R8B->R12B)
system_X-FLASH-ALL-C93B.sin:
/app/[lots changed, haven't extracted]
/bin/dnsmasq changed
/bin/customization/modem/* changed
/etc/firmware/(I honestly can't tell if it's a real change or just recompile changes)
/etc/permissions/privapp-permissions-google.xml added: permission name="android.permission.DISPATCH_PROVISIONING_MESSAGE"
/framework/(all oat, odex, art changed, no vdex's were changed except: boot-framework.vdex, boot-ims-common.vdex, boot-telephony-common.vdex)
/framework/framework-res.apk changed
/lib/hw/bluetooth.default.so changed
/lib/modules/* (I honestly can't tell if it's a real change or just recompile changes)
/lib/libandroid_runtime.so, libaudioflinger.so, libmediaplayerservice.so, libminikin.so, libpdfium.so, libsqlite.so, libstagefright.so, libstagefright_foundation.so, libstagefright_soft_avcdec.so, libvorbisidec.so
/lib64/hw/bluetooth.default.so
/lib64/libandroid_runtime.so, libaudioflinger.so, libdeqp_somc.so, libmediaplayerservice.so, libminikin.so, libnfc-nci.so, libpdfium.so, libsqlite.so, libstagefright.so, libstagefright_foundation.so, libstagefright_soft_avcdec.so, libvorbisidec.so
/priv-app/[lots changed, haven't extracted]
build.prop -> "ro.expect.recovery_id"
vendor_X-FLASH-ALL-C93B.sin:
/app/[lots change, haven't extracted],
/bin/hw/illumination_service
/bin/sct_service, sensors.qcom, updatemiscta
/etc/permissions/handheld_core_hardware.xml added
/etc/sepolicy/[files] some changes
/lib/camera/libexcal_multiframe_nr_plugin.so, libexcal_snapshot_ctrl_plugin.so
/lib/modules/qca_cld3_wlan.ko
/lib/soundfx/libdownmix.so, libreverbwrapper.so
/lib/libcammw.so, libexcal_system.so (face and object tracking?), libmmcamera2_iface_modules.so, libmmcamera2_imglib_modules.so, libmmcamera2_mct.so, libmmcamera2_sensor_modules.so, libmmcamera2_stats_modules.so, libOmxVenc.so, libpf.so (OMX video related), libril-qc-qmi-1.so
/lib64/soundfx/libdownmix.so, libreverbwrapper.so,
/lib64/libpf.so, libril-qc-qmi-1.so
build date changed
ro.setupwizard.rotation_locked=false added to props
There might be bits that I missed in the changed SINs, but the unchanged ones are unchanged.
Bear in mind that with the split firmware bits, sometimes it's difficult to determine if, say, "tzsuntory.b01" was actually changed, or if it was just a header difference due to a recompile. So I'm just ignoring the ones that I "think" are the same. That said, if I'm ignoring it, it's because it was contained in a SIN file that has other changes as well.
EDIT: I forgot to add that userdata_X-FLASH-ALL-C93B.sin is also unchanged.
Custom 21.329.01.00.00 firmware and 17.100.19.01.00 web interface for E5770
The firmware is based on the original global firmware version 21.329.01.00.00. It can be installed on any technological firmware, or updated from a modified firmware.
Flash using balongflash (Windows, Linux).
Attention!
This firmware can render your device unbootable! Use it only if you are aware of all the risks and consequences. In case of any problems, do not wait for help, you're on your own. Do not install firmware by non-tech-savvy people request, and do not sell routers with this firmware preinstalled.
Changes:
Firmware digital signature verification in the firmware server is disabled
Added support for IPv6 on mobile networks (disabled by default, could be activated "ipv6" script)
ADB installed and Telnet activated (disabled by default, controlled from the OLED menu)
The stock versions of busybox, iptables and ip6tables programs are replaced with full-fledged ones
The "atc" utility is installed to send AT commands from the console
Installed "ttl" script for modifying (fixing) TTL (for IPv4) and HL (for IPv6)
Installed "imei" script to change IMEI
A local transparent proxy server "tpws" and a script "anticensorship" are installed to circumvent censorship to sites from the registry of prohibited sites in Russian Federation (IPv4 only)
Added DNS over TLS resolver stubby (version 1.5.1, compiled with OpenSSL 1.0.2p) and DNS-level adblock (IPv4 only)
Added extended menu on OLED screen
Added RNDIS and ECM Ethernet switching functionality without a switch program on a computer
All NVRAM items are unlocked
AT^DATALOCK code is disabled
Added kernel module TUN/TAP (for OpenVPN and other programs)
Added OpenVPN (version 2.4.6, compiled with OpenSSL 1.0.2p) and scripts for DNS redirection
Added curl (version 7.63.0, compiled with OpenSSL 1.0.2p)
Added EXT4 kernel module and swap support
Added script for installing Entware application repository
Added script "adblock_update", for updating the list of advertising domains
Added script to change MAC address of Wi-Fi in Extender mode (script "wifiext_mac") and USB MAC addresses (script "usb_mac")
Removed mobile connection logging (mobile logger) to extend flash memory lifetime
Multilingual web interface with GSM/UMTS/LTE band selection menu
The extended menu on the OLED screen allows you to manage network mode (LTE/3G/GSM), TTL modification, circumvent censorship, ad blocking, IMEI change, USB composition, control access to the web interface, Telnet and ADB.
TTL modification and IMEI change require a reboot. The remaining menu items are applied instantly.
To activate extended menu, press left (WPS) button 7 times on Wi-Fi information screen.
The "anticensorship" script helps to bypass Deep Packet Inspection (DPI) systems on some operators in order to bypass web site blocking. It starts the local proxy server from zapret complex https://github.com/bol-van/zapret, modifying the packets in such a way as to complicate their analysis, and redirects all traffic to ports 80 (for HTTP) and 443 (for HTTPS) to local proxy. The proxy server works autonomously, without any third-party server on the Internet. It is recommended to use it in conjunction with DNS over TLS, in order to prevent possible DNS hijacking by the operator.
Advertisement blocking is performed on DNS level with dnsmasq DNS server. It works with DNS over TLS as upstream, requests for which are redirected if the corresponding menu item is activated from the OLED screen. EasyList and RuAdList https://forums.lanik.us/viewtopic.php?f=102&t=32524 from raletag and AdAway https://adaway.org/hosts.txt are used as an ad lists.
Ad-blocking at the DNS level works worse than full-fledged content blockers in browsers (AdBlock, µBlock), but it works on any device and in any program without additional settings.
You can also control ad blocking with the "dns_over_tls" script.
Domain lists could be updated using "adblock_update" command.
Entware application repository allows you to install additional Linux software from the armv7sf-k3.2 entware repository http://bin.entware.net/armv7sf-k3.2/Packages.html, using "opkg" package manager used in open source firmware for OpenWRT routers. Entware is installed using the "entware install" command. Entware files are installed in /opt, which is mounted in /online/opt. You can install many programs on 30 MB free space after installation on /online partition.
The router and Entware environments are independent of each other, the installed Entware software cannot be called from the router's environment, and the firmware programs and scripts cannot be called from the Entware. This was done to ensure that the installed packages would not conflict with files in the firmware.
To gain access to the Entware environment, use the "entware shell" command, to exit, type exit (or press CTRL+D).
Entware is designed for advanced users who understand how to customize and use installable programs. About 15 MB of free RAM is available in the router, the launch of heavy programs can lead to the crash of important services for the router (especially when DNS over TLS is enabled), remember that.
Download link
https://github.com/Huawei-LTE-routers-mods/Huawei_E5770_mod_fw_webui
More information about Huawei LTE routers (zeronet network): https://zn.amorgan.xyz/1HegcCNqxTuhPaHmjZwPGZ9LY34vXD6H1V/
E5770 O2 FW version 21.200.19.01.405 SIM unlock
Huawei E5770 from British O2 network with firmware version 21.200.19.01.405 could be unlocked for free with a special firmware, without disassembling the device.
This firmware is based on 21.200.19.01.405 version and could be installed without flash code.
E5770s_Update_21.200.19.01.405_o2_simunlock_signed.7z
If you want to install another official firmware or a custom firmware, you need to downgrade 21.200.19.01.405 to a special technological firmware version 21.180.99.10.00, which does not check firmware digital signatures.
E5770s_DOWNGRADE_o2_21.200.19.01.405_to_21.180.99.10.00_signed.7z
To install the firmware, press both RESET button (on the back of the device) and POWER button, connect it to the PC and use balongflash software (Windows, Linux)
More information about Huawei LTE routers (zeronet network): https://zn.amorgan.xyz/1HegcCNqxTuhPaHmjZwPGZ9LY34vXD6H1V/
Thabks for the share. Is it possible to unlock all bands to use it anywhere in the globe?
link not working
Hi I tried downloading the modded firmware but it only goes to 20% every time then hangs. can you fix please or host somewhere else.
many thanks
abiliotiago said:
Thabks for the share. Is it possible to unlock all bands to use it anywhere in the globe?
Click to expand...
Click to collapse
No, that's a hardware limitation. Different hardware modifications have different radio hardware. They could be converted by soldering some components though.
paybelb said:
Hi I tried downloading the modded firmware but it only goes to 20% every time then hangs. can you fix please or host somewhere else.
many thanks
Click to expand...
Click to collapse
You can download ZeroNet and download it from there, because ZeroNet to Internet gateways are unreliable.
E5770 FW version 21.327.01.00.1133, 21.200.19.01.405, 21.318.01.02.07 downgrade to technological 21.180.99.10.00
This special firmware allows installing technological firmware on firmware versions mentioned in the title, without entering OEM code (AT^DATALOCK), and without using test-point (needle method).
Technological firmware allows installing any other firmware (even with incorrect or corrupted signature), without any restrictions.
WARNING: If you flash this firmware, you won't be able to revert your old firmware version because there's no official firmware files of these version available in public access. You can install any other firmware though.
→ E5770s_DOWNGRADE_21.318.01.02.07_to_21.180.99.10.00 ←
→ E5770s_DOWNGRADE_21.327.01.00.1133_to_21.180.99.10.00 ←
→ E5770s_DOWNGRADE_21.200.19.01.405_to_21.180.99.10.00 ←
More information about Huawei LTE routers (zeronet network): https://zn.amorgan.xyz/1HegcCNqxTuhPaHmjZwPGZ9LY34vXD6H1V/
ValdikSS said:
No, that's a hardware limitation. Different hardware modifications have different radio hardware. They could be converted by soldering some components though.
Click to expand...
Click to collapse
Thanks for the explanation.
Which router do you recommend for the most compatibility LTE worldwide?
abiliotiago said:
Thanks for the explanation.
Which router do you recommend for the most compatibility LTE worldwide?
Click to expand...
Click to collapse
Probably something with Qualcomm chipset, which I'm not savvy in.
It depends on LTE bands or countries you're planning to use the device.
ValdikSS said:
Probably something with Qualcomm chipset, which I'm not savvy in.
It depends on LTE bands or countries you're planning to use the device.
Click to expand...
Click to collapse
Not sure right now
I just wanted something that could work for holidays wherever I decided to go
Thanks
unfortunatly balong_flash doesn't seem to work on windows 10
zebignasty said:
unfortunatly balong_flash doesn't seem to work on windows 10
Click to expand...
Click to collapse
worked fine for me on Windows 10 Pro
Version 2.3.1. Based on firmware 21.329.01.00.00 and webui 17.100.19.01.00
Changes since v2.3:
Firmware:
* Fix passwd_def telnet default password file
* Fix OpenVPN NAT scripts: properly remove added FORWARDING and INPUT DROP rules, clarify README
* Clarify net.{down,up} scripts
There are more than one variant of E5770.
Will this firmware work on E5770S-923 model?
BarakOsama said:
There are more than one variant of E5770.
Will this firmware work on E5770S-923 model?
Click to expand...
Click to collapse
Yes it will.
Hi OP,
my device is stuck on download mode.
can you please explain the flashing steps for the custom firmware.
As per your Read-Me the firmware should be flashed by balong_flash FLASH_FILE.BIN command.
Whats unclear to me is which file is to be flashed first. There are 2 .bin files in the custom firmware archive.
It will be a great help if you can give a step-by-step guide.
BarakOsama said:
Hi OP,
my device is stuck on download mode.
Click to expand...
Click to collapse
First of all, to install custom firmware you need to install technological firmware somehow. You can't install it just by flashing, it will require flash code which cannot be obtained easily. To bypass flash code check, I made downgrading firmwares for several firmware versions. You need to install downgrading firmware for your current firmware version, which will downgrade to technological firmware, and from technological firmware you can install any firmware, including custom one.
What exact steps did you perform, what exact result did you get?
ValdikSS said:
First of all, to install custom firmware you need to install technological firmware somehow. You can't install it just by flashing, it will require flash code which cannot be obtained easily. To bypass flash code check, I made downgrading firmwares for several firmware versions. You need to install downgrading firmware for your current firmware version, which will downgrade to technological firmware, and from technological firmware you can install any firmware, including custom one.
What exact steps did you perform, what exact result did you get?
Click to expand...
Click to collapse
After two days of googling I found the original firmware I had on the device and now the device is working again :victory:
Can you provide me a downgrading firmware to E5770s-923 21.316.03.00.1133 firmware version?.
E5770s_UPDATE_21.316.03.00.1133_WEBUI_17.100.13.02.1133_MRE5.zip
I flashed the custom firmware.
But somehow I cannot access the extended menu.
Software version: 21.329.01.00.00
Web UI version: 17.100.19.01.00
BarakOsama said:
I flashed the custom firmware.
But somehow I cannot access the extended menu.
Software version: 21.329.01.00.00
Web UI version: 17.100.19.01.00
Click to expand...
Click to collapse
You need to press left button 7 times on the wi-fi information screen.