NOTE: Before we begin, let me tell you that from my experience the D851 does not require shorting at all. it will be identified as Qualcomm HS-USB in a brick state without any opening up, check your device manager!
Hello guys, I spent 2 weeks analyzing hex files in order to revive a D851 that I got my hands on. It was not an easy journey but I would like to share this with the devs or people who are looking at bring their bricks to life.
What I did was actually hack the Sahara programmer files that WillCracker (BoardDiag) programs use. This comes in the attached files. Seems like there was no site on the Internet sharing this unique files and thus not allowing us to unrbick the D851.
For a more detailed view of how I got these modified files created please look at this post
But with this uniquely created files we now have unbrickable D851's , I have revived one D851 phone that I had dead. Right now it already booted into download mode and it is loading the *.tot.
Instructions
Connect your D851 phone without battery via USB to a Windows Box.
Make sure you have installed the HS USB 9008 Drivers installed. If so you will find something called "Qualcomm HS-USB QDLoader 9008 (COMxx)" under device manager, make sure you check the COM Port number, as you will need this later on the next step.
Open up BoardDiag.exe (from the downloaded files here, as it includes modified files specific for D851) and select: B2 (MSM8974AC), and pick up your COM Port.
Under 'Image Extraction' select your bin which should be the *.tot file (I used LG_D851.10C_TOT&DLL.7z).
Hit the 'extract' button into a directory of your choice.
Pick under 'COM Port' the 'Target Dir' and select where you have extracted the *.tot. This will allow us to start flashing the partition files.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Select on the checkbox "AP check".
Check the box called "RESTORE BOOT IMG", in here start picking up the partitions, write each one of them (not system, userdata or cache -- those are worthless for now), and ONLY in the end flash LAF and then finally SBL*. After this you will see the phone boot up with the battery icon since you do not have a battery connected. This is when you can tell you have now the bootloader reflashed.
Unplug the USB cable, insert the battery into the phone and hold UP while hooking up the USB cable again. After doing this your phone will boot up in download mode and now you can go ahead and flash the correct firmware using a tool such as LGFlashTool.
Below you can see a screenshot of the dmesg showing that it is already in download mode (after being in QC HS USB 9008 mode)... I am so !"#$ happy
I flashed the partitions like in this other guide but please use the attached file or else it won't work.
NOTE: Do download the attached Willcracker Version I attached specific for the D851, this is a modified one and is the only type of program I managed to use to revive my phone. I cannot stop insisting that any other set of files will not work on our D851, which is what most people reported on the forums for some time.
EXTRA: Disable Windows driver update, updating the Qualcomm HS-USB driver can cause conflicts and problems on the process.
<< If you like my work here is my hat, please donate! >>
hello please i ask for your help
thank you for the great work man
can you please help me in my phone has same problem now it is a month
the problem is that my phone is lg f460s
i have the tot file but because it is a different chip-set Apq8084 this app BoardDiag doesn't support it
can you please modify the app
i searched in so many Korean forums nothing there and Russian forums too
please i donate for you man if you could find .hex singleimage.bin
i gave my phone to some people here but all of them doesn't know how to solve this boot loader problem i knew it can be fixed only by medusa box or octubos box which no body have it here
i found some files which it can revive some other phones having the same processor qualcomm snapdragon 805 like Motorola turbo and nexus 6
like these images
these unbrick files can communicate with lg f460s but because it need a right singleimage and .hex files it cant fix it
please bro try to look for this model i tried for so many weeks now
and thank you again
it fully work
thank u so much
i found your port last night
and it isnt have instruction
so i do by my self with your tool
you are my hero , you saved me thank you sooo much bro , my phone booted in fastboot mode after this , i ll try to flash frimeware now , biiig thnaks to you man
Jyed said:
you are my hero , you saved me thank you sooo much bro , my phone booted in fastboot mode after this , i ll try to flash frimeware now , biiig thnaks to you man
Click to expand...
Click to collapse
No problem man. I am also so glad to have unrbicked that phone as I can now give it to my dad as his phone (a really old Samsung Galaxy S3 was dying of slowness). I hated to have a ~$200.00 brick :cyclops: not being used! And I am a big fan of this LG G3 phone.
Btw, what I did after unrbciking first after fastboot started was that I shutted down my phone by removing the battery, and disconnected the USB cable. Then I reinsrted the battery and put it in download mode by using the: 'Keep pressing up and insert the USB cable'... and after that re-flashed the *.tot using downloaded mode as it is way faster with LGFlashTool.
Amazing work man… my D851 is working now. Earlier it failed to boot in all other methods. Thank u so much
@Omar-Avelar , Man, today i've seen my pm box and checked your message and looked here, nothing to say just.
THANKS, YOU SAVED ME! THANKS A LOT.
I've set the phone in download mode now, but when it begin the d851 firmware flash says cross DL SWversion, thats because i have a frankenstain phone, thats what've caused me a brick, what i need to do to set the d851 firmware?
Look at the images
ERROR:
My phone in dload mode says that:
and my motherboard:
I suposse that it can be fixed, but what i need to do?.
THANKS AGAIN MASTER! IM SO HAPPY
Where can i donate to you? Sorry for my english haha.
Edit: i've saw your firm now i'll donate you.
adrianbravom said:
@Omar-Avelar , Man, today i've seen my pm box and checked your message and looked here, nothing to say just.
THANKS, YOU SAVED ME! THANKS A LOT.
I've set the phone in download mode now, but when it begin the d851 firmware flash says cross DL SWversion, thats because i have a frankenstain phone, thats what've caused me a brick, what i need to do to set the d851 firmware?
I suposse that it can be fixed, but what i need to do?.
THANKS AGAIN MASTER! IM SO HAPPY
Where can i donate to you? Sorry for my english haha.
Edit: i've saw your firm now i'll donate you.
Click to expand...
Click to collapse
I've faced the same fate as you because I flashed a D855 on a Phone that was a refurbished D851. Took me like a month to figure out how to unbrick it.
By the looks of it it seems that your phone still has the LAF partition of the D855 but you recovered the other bootloder partition files allowing you to boot into the download mode 'thinking' it is a D855.
I suggest you use the LGUP_8974.dll instead of the 'supposed' D851 *.dll in the *.tot files... I think that will flash the partitions regardless if it is a D855 or 851 and force enter the files.
Omar-Avelar said:
I've faced the same fate as you because I flashed a D855 on a Phone that was a refurbished D851. Took me like a month to figure out how to unbrick it.
By the looks of it it seems that your phone still has the LAF partition of the D855 but you recovered the other bootloder partition files allowing you to boot into the download mode 'thinking' it is a D855.
I suggest you use the LGUP_8974.dll instead of the 'supposed' D851 *.dll in the *.tot files... I think that will flash the partitions regardless if it is a D855 or 851 and force enter the files.
Click to expand...
Click to collapse
Well, that images posted before whas with lgup_8974.dll and gives me the errors, I think I need to modify the hex file to put it as a "d855" and makes the program recognizes it, me fear is that if I flash the d851 firmware maybe I can loose the imei a mobile information ( before the brick the phone has d855 software ) or it will not erase my efs partition ? What u recommend me ? Flash d855 or d851 tot?
adrianbravom said:
Well, that images posted before whas with lgup_8974.dll and gives me the errors, I think I need to modify the hex file to put it as a "d855" and makes the program recognizes it, me fear is that if I flash the d851 firmware maybe I can loose the imei a mobile information ( before the brick the phone has d855 software ) or it will not erase my efs partition ? What u recommend me ? Flash d855 or d851 tot?
Click to expand...
Click to collapse
If it is a D851 motherboard but seen as a D855 via firmware I would try using the *.dll of D855 and the *.tot file of D851.
Seems like while being in HS-USB 9008 mode one of the partitions was not flashed correctly and the downloader mode still sees it as D855. The other option would be to brick it again with D855 *.dll and *.tot if the first try does not work. And while being in HS-USB 9008 mode please make sure you do flash most of the partitions there (not system, nor userdata, not cache) but the rest and end up with LAF > SBL* partition. That will flash the correct *.tot files for D851 and hopefully you will see the D851 now as D851 in the downloader mode.
I believe IIRC that the LAF partition has the downloader, and that's the one I believe is still written from when you overwrote it as a D855. If you wrote SBL* before LAF it might have booted with the LAF partition of the D855.
All done! Phone works and is alive!, @Omar-Avelar i've did what i told you, i've used a hex editor in a linux distro and modified the first "D851" mention to "D855" and goodbye CrossDL error, flashed sucessly, now my phone it's a real D851 and its hardunbricked! thanks all to you, you are great!.
Thank you, sir. You are live saver.
I have bricked my phone (d851) and I had been looking for days and nothing works.
Fortunately, I went to this thread and had successfully unbrick my phone.
God bless you.
D851 unbrickable
Omar-Avelar said:
I've faced the same fate as you because I flashed a D855 on a Phone that was a refurbished D851. Took me like a month to figure out how to unbrick it.
By the looks of it it seems that your phone still has the LAF partition of the D855 but you recovered the other bootloder partition files allowing you to boot into the download mode 'thinking' it is a D855.
I suggest you use the LGUP_8974.dll instead of the 'supposed' D851 *.dll in the *.tot files... I think that will flash the partitions regardless if it is a D855 or 851 and force enter the files.
Click to expand...
Click to collapse
My case is almost similar. As per software info it was d855 before bricking. So I flashed mm kdz for d855 and bricked.then I opened the cover and found this has a d851 board. So ,as per this tutorial I flashed everything for d851.phone booted but booting into fastboot mode only no download mode. Then I followed some other tutorial and again flashed laf. Img .now it can enter in download mode. But have a big problem .As it was a real d851 rom it cant connect to 3g net work here in india(2g ok). Now I am so disappointed because such a good phone with 2g only.....
But how initially d855 rom was flashed on d851 board???? There may be a way..
Ofcourse only beacuse of thread my g3 is live now. Please help me to get full out put from that.
There are threads to manually add bands to qualcomm device.Can I go for that?
[Update; Duplicated post]
justinmartin111 said:
My case is almost similar. As per software info it was d855 before bricking. So I flashed mm kdz for d855 and bricked.then I opened the cover and found this has a d851 board. So ,as per this tutorial I flashed everything for d851.phone booted but booting into fastboot mode only no download mode. Then I followed some other tutorial and again flashed laf. Img .now it can enter in download mode. But have a big problem .As it was a real d851 rom it cant connect to 3g net work here in india(2g ok). Now I am so disappointed because such a good phone with 2g only.....
But how initially d855 rom was flashed on d851 board???? There may be a way..
Ofcourse only beacuse of thread my g3 is live now. Please help me to get full out put from that.
There are threads to manually add bands to qualcomm device.Can I go for that?
Click to expand...
Click to collapse
Yes, it is such a great feeling to be able to bring the phone back from the death.
BTW, I do believe also the phone bands can be changed using QPST since I have seen Argentinian D855 phones changed to D855P (Adding another LTE band).
You might need another phone reference (LG G3 that worka on the band you want) and using QPST might let you modify some specifics.
Go ahead and Google translate this post for analysis: http://www.grupoandroid.com/topic/112493-guia-habilitar-bandas-lte-para-argentina-en-d855-int/
Another success in reviving the dead lg g3
Omar-Avelar said:
NOTE: Do download the attached Willcracker Version I attached specific for the D851, this is a modified one and is the only type of program I managed to use to revive my phone. I cannot stop insisting that any other set of files will not work on our D851, which is what most people reported on the forums for some time.
Click to expand...
Click to collapse
Thank your thread was really helpful in getting somewhere, You are the champion :good::victory:
---------- Post added at 07:53 AM ---------- Previous post was at 07:52 AM ----------
adrianbravom said:
All done! Phone works and is alive!, @Omar-Avelar i've did what i told you, i've used a hex editor in a linux distro and modified the first "D851" mention to "D855" and goodbye CrossDL error, flashed sucessly, now my phone it's a real D851 and its hardunbricked! thanks all to you, you are great!.
Click to expand...
Click to collapse
Can you please direct me somewhere or guide by yourself on how to do this.
Hey , could anyone help me? i have a lg l40 d175f, and i have boarddiag ,the kdz files but i do not have the partition.txt, what do I have to do??? please save me, this is not a monster phone but i don't have money to buy another one
Omar-Avelar said:
[*]Open up BoardDiag.exe (from the downloaded files here, as it includes modified files specific for D851) and select: B2 (MSM8974AC), and pick up your COM Port.
Click to expand...
Click to collapse
Modified Files huh??
The miracle file is a file that has been around all along. It can be found in the Smartboot Diag Tool. Its called LGD851_ATMO_TMUS.mbn.
All you have to do is rename this file to 2nd_loader.hex and put it inside the Board DIag Tool > Model > B2(MSM8974AC) Folder. Replace this file with the old one.
Now start Board Diag tool and load and decompress your tot file, and flash away.
For other models, you could try renaming your devices mbn from the Smartboot Diag tool to 2nd_loader.hex
wow
mickeyasamoah said:
Modified Files huh??
The miracle file is a file that has been around all along. It can be found in the Smartboot Diag Tool. Its called LGD851_ATMO_TMUS.mbn.
All you have to do is rename this file to 2nd_loader.hex and put it inside the Board DIag Tool > Model > B2(MSM8974AC) Folder. Replace this file with the old one.
Now start Board Diag tool and load and decompress your tot file, and flash away.
For other models, you could try renaming your devices mbn from the Smartboot Diag tool to 2nd_loader.hex
Click to expand...
Click to collapse
can you provide same file for lg g3 f460s ? it has chipset apq8084 . thank you i advance
ExtraDemo said:
can you provide same file for lg g3 f460s ? it has chipset apq8084 . thank you i advance
Click to expand...
Click to collapse
I am currently in class. Will check when I get home.
Related
Hi everyone,
I got F240L for about 2 months.
Got software problem last months from a post http://forum.xda-developers.com/showthread.php?t=2380374
Repair to some phone shop, he got no clue neither. Left my phone in CWM.
So, I use KDZ Updater + download KDZ file from pan.baidu.com (get it to work again).
I got curious, so I install Dungeon Hunter 4 again. Again, software problem occurs, even I uninstall the game. KDZ Updater and LG Mobile Support Tool left my phone stuck in U+ LTE logo.
Browse the web, then I read someone whose using LG Flashtool (it need DLL and TOT file) to flash the phone.
Search those two files every web, finally got it.
LG Flashtool step by step guide http://forum.gsmhosting.com/vbb/f177/lg-flash-tool-free-no-need-b2b-user-pass-1628819/index2.html
And got LGUP_GKV.DLL from extracting F240L10t_00.kdz from pan.baidu.com (see attachment), this file has the same size for F240K and F240S, so it must be compatible for F240L, F240S, F240K.
And got TOT file from http://www.gaojituan.com/thread-90-1-1.html or http://optimusforums.com/threads/f240-optimus-g-pro-firmware-downloads.7679
I hope this solution might help someone who ever got this problem.
NB : After 600 seconds flashing progress using LG Flashtool, don't put your phone in LG SOFTWARE MODE. Somehow, the phone got it reboot in DOWNLOAD MODE, and LG Flashtool will reflash your phone for the 2nd time (start from 1% progress again).
It not work with Hard Brick (black screen). tried it, not success.
khengvantha said:
It not work with Hard Brick (black screen). tried it, not success.
Click to expand...
Click to collapse
has anyone started to jtag fix the hard brick yet ??
Hard brick issue
Sorry, I'm also a noob here.
Can your phone go to DOWNLOAD MODE ?
I read on hongkong website (got it translate from google) 2 weeks ago, someone already try LGNPST, KDZ Updater, R&D Tool, LG Mobile Support Tool, still didn't work. The other guy recommend that you should have it fix by LG guy in Korea, or use JTAG device.
I even don't know what JTAG device is.
Maybe someone in this forums can explain you how.
Sorry if my word can be misleading.
I'll update the thread to delete the word "Hard Brick"
You are a wonderful and creative
It has succeeded with me
Glad could help.
In the mean time, enjoy this super AWESOME phone.
chimmot307 said:
Glad could help.
In the mean time, enjoy this super AWESOME phone.
Click to expand...
Click to collapse
Hi I'm stuck man. Having problems with maps and so I reset now the phone stays in CWM try to reboot but back to CWM. Cant flash rom from sd card or external card. PLease help.
Where did you download KDZ files etc?
chimmot307 said:
Hi everyone,
I got F240L for about 2 months.
Got software problem last months from a post http://forum.xda-developers.com/showthread.php?t=2380374
Repair to some phone shop, he got no clue neither. Left my phone in CWM.
So, I use KDZ Updater + download KDZ file from pan.baidu.com (get it to work again).
I got curious, so I install Dungeon Hunter 4 again. Again, software problem occurs, even I uninstall the game. KDZ Updater and LG Mobile Support Tool left my phone stuck in U+ LTE logo.
Browse the web, then I read someone whose using LG Flashtool (it need DLL and TOT file) to flash the phone.
Search those two files every web, finally got it.
LG Flashtool step by step guide http://forum.gsmhosting.com/vbb/f177/lg-flash-tool-free-no-need-b2b-user-pass-1628819/index2.html
And got LGUP_GKV.DLL from extracting F240L10t_00.kdz from pan.baidu.com (see attachment), this file has the same size for F240K and F240S, so it must be compatible for F240L, F240S, F240K.
And got TOT file from http://www.gaojituan.com/thread-90-1-1.html or http://optimusforums.com/threads/f240-optimus-g-pro-firmware-downloads.7679
I hope this solution might help someone who ever got this problem.
NB : After 600 seconds flashing progress using LG Flashtool, don't put your phone in LG SOFTWARE MODE. Somehow, the phone got it reboot in DOWNLOAD MODE, and LG Flashtool will reflash your phone for the 2nd time (start from 1% progress again).
Click to expand...
Click to collapse
Could you please provide instructions on how to use KDZ updater? Where did you download it from or if you could PM? thanks
I'm downloading software via LG Mobile support but at the moment its going to take 30hrs!!
KDZ updater & LG Mobile Support Tool won't help.
You need to download LG Flashtool 1.5 is the latest version on the link that on #1 post. Once you download, follow the procedure how to install the LG Flashtool.
LG Flashtool needs 2 files (DLL & TOT) to flash your phone.
You can download DLL file from the attachment on #1 post. The attachment is compressed in RAR format. You can extract it using Winzip, Winrar, or 7zip.
The TOT file is on the 2 link #1 post (chinese website & optimus forums). You need to download the approriate type according to your phone (F240L, F240K, F240S) each files about 2 GB size. I suggest you use any download manager, to prevent disconnect from bad interference or time out. I can't post the TOT file here too due to slow network in my country (Indonesia) .
After you collect those DLL & TOT files, here's step by step :
1. Disconnect any internet connection
2. Set the computer time before Juli 15th, 2012 ( I set March 1st, 2012)
3. Double click LG Flashtool. Username, password, and Registration key are on the link #1 post
4. Insert DLL file in DLL column. Browse to where you put the DLL file.
5. Insert TOT file in Software column. Browse to where you put the TOT file.
6. Click OK
7. Click the GEAR icon, set only port #1 that ticked. Other ports are UNTICKED. Click OK.
8. Press & hold volume UP and DOWN, while connecting the USB cable to your computer (set to DOWNLOAD MODE). Until the phone shows "DOWNLOAD MODE" on the center of the screen.
9. Open System Properties. Set COM port for LG Handset using port 41.
10. Click Arrow Right in LG Flashtool, disconnect USB cable for 5 seconds. Reconnect USB cable.
11. The FLASH process in progress, wait for 600 seconds and shows green background say "PASS".
12. Disconnect USB cable and close the LG Flashtool application.
13. Release the battery, wait for 3 minutes.
14. Do FACTORY RESET in SETTINGS. End of FLASHING process.
Enjoy !!!
Thanks for that very clear instructions.
Sent from my LG-F240L using Tapatalk 2
I need LGE988.DLL. Can any one help?
chimmot307 said:
Hi everyone,
I got F240L for about 2 months.
Got software problem last months from a post http://forum.xda-developers.com/showthread.php?t=2380374
Repair to some phone shop, he got no clue neither. Left my phone in CWM.
So, I use KDZ Updater + download KDZ file from pan.baidu.com (get it to work again).
I got curious, so I install Dungeon Hunter 4 again. Again, software problem occurs, even I uninstall the game. KDZ Updater and LG Mobile Support Tool left my phone stuck in U+ LTE logo.
Browse the web, then I read someone whose using LG Flashtool (it need DLL and TOT file) to flash the phone.
Search those two files every web, finally got it.
LG Flashtool step by step guide http://forum.gsmhosting.com/vbb/f177/lg-flash-tool-free-no-need-b2b-user-pass-1628819/index2.html
And got LGUP_GKV.DLL from extracting F240L10t_00.kdz from pan.baidu.com (see attachment), this file has the same size for F240K and F240S, so it must be compatible for F240L, F240S, F240K.
And got TOT file from http://www.gaojituan.com/thread-90-1-1.html or http://optimusforums.com/threads/f240-optimus-g-pro-firmware-downloads.7679
I hope this solution might help someone who ever got this problem.
NB : After 600 seconds flashing progress using LG Flashtool, don't put your phone in LG SOFTWARE MODE. Somehow, the phone got it reboot in DOWNLOAD MODE, and LG Flashtool will reflash your phone for the 2nd time (start from 1% progress again).
Click to expand...
Click to collapse
It's asking to sign in before downloading file. Any other links for firmware!
riz157 said:
It's asking to sign in before downloading file. Any other links for firmware!
Click to expand...
Click to collapse
Almost there but message keeps showing download error?
chimmot307 said:
Hi everyone,
I got F240L for about 2 months.
Got software problem last months from a post http://forum.xda-developers.com/showthread.php?t=2380374
Repair to some phone shop, he got no clue neither. Left my phone in CWM.
So, I use KDZ Updater + download KDZ file from pan.baidu.com (get it to work again).
I got curious, so I install Dungeon Hunter 4 again. Again, software problem occurs, even I uninstall the game. KDZ Updater and LG Mobile Support Tool left my phone stuck in U+ LTE logo.
Browse the web, then I read someone whose using LG Flashtool (it need DLL and TOT file) to flash the phone.
Search those two files every web, finally got it.
LG Flashtool step by step guide http://forum.gsmhosting.com/vbb/f177/lg-flash-tool-free-no-need-b2b-user-pass-1628819/index2.html
And got LGUP_GKV.DLL from extracting F240L10t_00.kdz from pan.baidu.com (see attachment), this file has the same size for F240K and F240S, so it must be compatible for F240L, F240S, F240K.
And got TOT file from http://www.gaojituan.com/thread-90-1-1.html or http://optimusforums.com/threads/f240-optimus-g-pro-firmware-downloads.7679
I hope this solution might help someone who ever got this problem.
NB : After 600 seconds flashing progress using LG Flashtool, don't put your phone in LG SOFTWARE MODE. Somehow, the phone got it reboot in DOWNLOAD MODE, and LG Flashtool will reflash your phone for the 2nd time (start from 1% progress again).
Click to expand...
Click to collapse
Thanks for that when I try it I get message download fail in red? What I'm I doing wrong?
It goes to 100% then download fail. I think you faced similar issue not sure what I'm doing wrong.
You need to follow step #9
This is LGE980 DLL http://forum.xda-developers.com/showthread.php?t=2302660
Tot file download
chimmot307 said:
KDZ updater & LG Mobile Support Tool won't help.
You need to download LG Flashtool 1.5 is the latest version on the link that on #1 post. Once you download, follow the procedure how to install the LG Flashtool.
LG Flashtool needs 2 files (DLL & TOT) to flash your phone.
You can download DLL file from the attachment on #1 post. The attachment is compressed in RAR format. You can extract it using Winzip, Winrar, or 7zip.
The TOT file is on the 2 link #1 post (chinese website & optimus forums). You need to download the approriate type according to your phone (F240L, F240K, F240S) each files about 2 GB size. I suggest you use any download manager, to prevent disconnect from bad interference or time out. I can't post the TOT file here too due to slow network in my country (Indonesia) .
After you collect those DLL & TOT files, here's step by step :
1. Disconnect any internet connection
2. Set the computer time before Juli 15th, 2012 ( I set March 1st, 2012)
3. Double click LG Flashtool. Username, password, and Registration key are on the link #1 post
4. Insert DLL file in DLL column. Browse to where you put the DLL file.
5. Insert TOT file in Software column. Browse to where you put the TOT file.
6. Click OK
7. Click the GEAR icon, set only port #1 that ticked. Other ports are UNTICKED. Click OK.
8. Press & hold volume UP and DOWN, while connecting the USB cable to your computer (set to DOWNLOAD MODE). Until the phone shows "DOWNLOAD MODE" on the center of the screen.
9. Open System Properties. Set COM port for LG Handset using port 41.
10. Click Arrow Right in LG Flashtool, disconnect USB cable for 5 seconds. Reconnect USB cable.
11. The FLASH process in progress, wait for 600 seconds and shows green background say "PASS".
12. Disconnect USB cable and close the LG Flashtool application.
13. Release the battery, wait for 3 minutes.
14. Do FACTORY RESET in SETTINGS. End of FLASHING process.
Enjoy !!!
Click to expand...
Click to collapse
PLZ TELL ME HOW CAN I DOWNLOAD TOT FILE baidu is not working
You can download from http://www.gaojituan.com/thread-90-1-1.html or http://optimusforums.com/threads/f240-optimus-g-pro-firmware-downloads.7679/
Click on the latest TOT file according to its date and your phone (F240L, F240S, F240K).
I've test on F240L v10i from http://www.gaojituan.com/thread-90-1-1.html works very well on pan.baidu.com.
Which file are you try to download ? Which phone do you use ?
I tried the procedures you guys mentioned above, but my phone does not seem to be being flashed.
Everything seems alright, up until disconnect the USB cable and wait for 5 secs to reconnect, but after reconnect, nothing happen....
mine is F240S, does it matter? How do I extract DLL from TOT or KDZ files?
Thanks in advanced
Dennis
---------- Post added at 11:01 PM ---------- Previous post was at 10:23 PM ----------
I actually finally got it flashed, all the procedures are correct, just need to time that 5 secs accurately.
Also, anyone with F240S needs to stay with the version of Flashtool that OP provided, any version higher than 1.4 seems giving me error.
Thanks very much for the info.
Dennis
Please help...
Guys plzzz help... I have F240s. first i was rooted on stock and then flashed cwm along with loki patch file (easy-cwm-f240s.zip file). i wanted EDGE on my
phone (i m in pakistan and only gprs works here on this phone) so i flashed panama rom by flash tool but lost the signal service.. i Wiped system,data,cache in CWM and restored data of my stock
rom from CWM but still no signals ( mobile model was still showing up e980h from panama rom) then i factory reset and flashed Cm 10.1 of f240s (i think i may have wiped system ,cache and date before it). now when i power on, LG logo appears on screen and in left top side it says:
Secure booting Error
Cause: boot Certification Verify
unfortunately i also had below 30% battery when i flashed cm10.1. NOW if i go to download mode and use mobile support tool
and flash tool to update it says: battery level is low and upgrade is unavailable, fully recharge ur battery and try again.
I Have used a battery stand charger to charge for 3 hrs but after checking phone software setting for 3,4 minutes it still says the same thing about battery again n again. should i let it charge to 100% no
matter how long it takes and then try or do something elsee... plzzz helppp
Up Rom Unbrick LG Soft Brick G3
* Thank @wolfgart files.
* This method is for the original rom you run up test by which failed not stop at 2% or 49% or a low battery detector okay.
* I have done successfully on the LG G3 plant F400L/S/K so I wrote this article to share with you to protect your children's G3.
* Download drawing tools.
FlashTool v1.8.1
* File. Tottenham
F400K V10B
Files. DLL F400K
F400L V10A
Files. DLL F400L
F400S V10B
Files. DLL F400S
Latest drivers for LG
- Down to copy the folder containing the file. Tottenham that you have downloaded the firmware for each and renamed with the name of the file EXACTLY. Tot that you down in the
Now proceed:
1 / Put the download mode mode
2 / Set FlashTool v1.8.1. Let it run the default setup install to C: \ LG \ LGFlashtool
3 / LGflashtool Crack Down on It is Megalock.dll file, copy it to the root of the LG Flash Tool folder in C: \ LG \ LgFlashtool
4 / Put G3 in download mode. Plugged into the computer. Open Device Manager to make the picture below.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5 / Note the COM port, the COM port you can be different, so follow the image below to convert from any COM port to COM 41.
6 / LG Flash Tool Open earlier you set it up it will be one table, select all the items exactly as shown below (the machine running Win 7 + 8 select Open as Admin offline).
press OK
7 / After you click OK, it will show you the following table and the yellow button.
8 / After the yellow button it will run as follows.
Games you wait 2-3 minutes for it to run
9 / After running it will appear as shown below:
10 / then you disconnect the USB cable connected to your computer with G3, wait 5 seconds, then plug the cable, wait 5 seconds longer range it will run as follows:
Wait for it to run, remember to mind on tel will run until rebooot back, you still plug the cable, no cable pulled offline!
When you reboot the machine on FlashTool G3 will appear as follows:
Wait G3 boot into Android dc disconnect the cable, the setup screen: D enjoy the fruits!
vandieutot said:
Up Rom Unbrick LG Soft Brick G3
* This method is for the original rom you run up test by which failed not stop at 2% or 49% or a low battery detector okay.
* I have done successfully on the LG G3 plant F400L/S/K so I wrote this article to share with you to protect your children's G3.
* Download drawing tools.
FlashTool v1.8.1
* File. Tottenham
F400K V10B
F400L V10B
F400S V10B
Files. DLL F400S/L/K
Latest drivers for LG
- Down to copy the folder containing the file. Tottenham that you have downloaded the firmware for each and renamed with the name of the file EXACTLY. Tot that you down in the
Now proceed:
1 / Put the download mode mode
2 / Set FlashTool v1.8.1. Let it run the default setup install to C: \ LG \ LGFlashtool
3 / LGflashtool Crack Down on It is Megalock.dll file, copy it to the root of the LG Flash Tool folder in C: \ LG \ LgFlashtool
4 / Put G3 in download mode. Plugged into the computer. Open Device Manager to make the picture below.
5 / Note the COM port, the COM port you can be different, so follow the image below to convert from any COM port to COM 41.
6 / LG Flash Tool Open earlier you set it up it will be one table, select all the items exactly as shown below (the machine running Win 7 + 8 select Open as Admin offline).
press OK
7 / After you click OK, it will show you the following table and the yellow button.
8 / After the yellow button it will run as follows.
Games you wait 2-3 minutes for it to run
9 / After running it will appear as shown below:
10 / then you disconnect the USB cable connected to your computer with G3, wait 5 seconds, then plug the cable, wait 5 seconds longer range it will run as follows:
Wait for it to run, remember to mind on tel will run until rebooot back, you still plug the cable, no cable pulled offline!
When you reboot the machine on FlashTool G3 will appear as follows:
Wait G3 boot into Android dc disconnect the cable, the setup screen: D enjoy the fruits!
MOD EDIT: Please don't quote the entire OP
Click to expand...
Click to collapse
tot and dll files are mine, i've uploaded for first on the WEB and you have used them . This is the section : http://forum.xda-developers.com/showthread.php?t=2771401
You should at least "Thank you" before using files
PERFECT.
BUT I need F400S TOT file...
Is there somebody who upload F400S tot file for me?
wolfgart said:
tot and dll files are mine, i've uploaded for first on the WEB and you have used them . This is the section : http://forum.xda-developers.com/showthread.php?t=2771401
You should at least "Thank you" before using files
Click to expand...
Click to collapse
I thank you. Sorry you because of this careless okay.
Thank wolfgart files. Please ask when they have F400S and F400L, sir.
Hi @vandieutot. I think a guide, how to and tools are better placed in the General section. I usually never search within Q&A.
However, your thread is in the LG G3 index
benkxda said:
Hi @vandieutot. I think a guide, how to and tools are better placed in the General section. I usually never search within Q&A.
However, your thread is in the LG G3 index
Click to expand...
Click to collapse
I thank you for your interest in the topic I created. But I do not understand your disposal. You can not say more.
vandieutot said:
I thank you for your interest in the topic I created. But I do not understand your disposal. You can not say more.
Click to expand...
Click to collapse
To move the thread, just click on the exclamation mark triangle sign at the top right of your first post.Then place a statement like "started thread in wrong forum, please move into the LG G3 General forum" and choose, "Thread/post moving or maintenance" from the drop down menu and a moderator will take care of your request.
mtp driver problem
my phone is stuck in bootloop after I tried to flash a ROM, so I tried to use the TOT method but I having a problem the MTP driver installation failure, I tried all kind of drivers but still wont install, what should I do now?
Help!
I have a F400K model, I was able to root and flash the 2 custom roms (Sphinx /VTD) fine, but when I tried to flash back to factory stock, my phone now shows it's a F400L model for some reason. So trying to flash the F400K tot file doesn't work (It works with F400L though). Is there anyway to get back to the original F400K model?
---------- Post added at 10:01 AM ---------- Previous post was at 09:57 AM ----------
lovers74 said:
my phone is stuck in bootloop after I tried to flash a ROM, so I tried to use the TOT method but I having a problem the MTP driver installation failure, I tried all kind of drivers but still wont install, what should I do now?
Click to expand...
Click to collapse
From your first screenshot, I think you have the same issue as me, the phone is recognized since it wont get to that error if your driver is not working. I was able to flash F400L tot file on my phone even though I have an F400K model. Just posted and hopefully someone can help and provide details on what I need to do in order to flash the original F400K factory firmware on my phone.
OZJeff said:
I have a F400K model, I was able to root and flash the 2 custom roms (Sphinx /VTD) fine, but when I tried to flash back to factory stock, my phone now shows it's a F400L model for some reason. So trying to flash the F400K tot file doesn't work (It works with F400L though). Is there anyway to get back to the original F400K model?
---------- Post added at 10:01 AM ---------- Previous post was at 09:57 AM ----------
From your first screenshot, I think you have the same issue as me, the phone is recognized since it wont get to that error if your driver is not working. I was able to flash F400L tot file on my phone even though I have an F400K model. Just posted and hopefully someone can help and provide details on what I need to do in order to flash the original F400K factory firmware on my phone.
Click to expand...
Click to collapse
Yes same thing happened to me, it turns out that its not a driver issue my phone accepted the F400L TOT file although my device is F400K it is strange.
my phone is stuck at factory reset status 2. Everything went fine until the last part and it failed...
EDIT: I installed the latest flash-tool and re downloaded the dll and tot files and its still failing at the very end....
EDIT 2:
I have tried again, and still nothing. It will sometimes get to 99% and then fail, and other times it won't make it past 11-12%. I re installed the latest drivers, flash tool, and re-downloaded the dll and tot files. Does anyone know how to unbrick it? The most it will do is get to factory reset status 2, but then if I run it again after it fails it won't find my phone, and it only boots into download mode. It's a never ending loop of that or factory reset status 2 no matter what I try. I would really appreciate any help. I have a F400S and I downloaded all of the correct files from the other posts. My phone crashed after flashing a ROM and now well, here I am.
Pilz said:
my phone is stuck at factory reset status 2. Everything went fine until the last part and it failed...
EDIT: I installed the latest flash-tool and re downloaded the dll and tot files and its still failing at the very end....
EDIT 2:
I have tried again, and still nothing. It will sometimes get to 99% and then fail, and other times it won't make it past 11-12%. I re installed the latest drivers, flash tool, and re-downloaded the dll and tot files. Does anyone know how to unbrick it? The most it will do is get to factory reset status 2, but then if I run it again after it fails it won't find my phone, and it only boots into download mode. It's a never ending loop of that or factory reset status 2 no matter what I try. I would really appreciate any help. I have a F400S and I downloaded all of the correct files from the other posts. My phone crashed after flashing a ROM and now well, here I am.
Click to expand...
Click to collapse
Hey guys! PLEASE help! I also am stuck on the blue screen " Factory Reset Status 3.. Any advice or suggestions, please?
---------- Post added at 04:18 PM ---------- Previous post was at 03:56 PM ----------
I decided to stop waiting for an automatic reboot and removed the battery. Waited for about 10 seconds, popped in the battery .. rebooted and I have stock unrooted! Thank you so much !!!
Showtek1980 said:
Hey guys! PLEASE help! I also am stuck on the blue screen " Factory Reset Status 3.. Any advice or suggestions, please?
---------- Post added at 04:18 PM ---------- Previous post was at 03:56 PM ----------
I decided to stop waiting for an automatic reboot and removed the battery. Waited for about 10 seconds, popped in the battery .. rebooted and I have stock unrooted! Thank you so much !!!
Click to expand...
Click to collapse
After factory reset stays 3 don't unplug the cable and it should reboot and startup that's the ending step.
Sent from my SAMSUNG-SM-N900A using XDA Premium 4 mobile app
Pilz said:
After factory reset stays 3 don't unplug the cable and it should reboot and startup that's the ending step.
Sent from my SAMSUNG-SM-N900A using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hi there! Thanks for you reply I waited long enough for a reboot and I decided to unplug the cable, remove the battery and thank my lucky stars it rebooted up well... I managed to update to the latest version .. Version F400k10g.. (Since I'm in Korea). I read somewhere on the LG G3 forum that you can only unplug after " Factory reset status 3 ".. But I read that after I took the "risk"
No luck
No luck...
D855 (I think)
Flash tool gives me this every time
This was also not helpfull :/
http://forum.xda-developers.com/showthread.php?p=53796705
Any ideas?
thermopoli said:
No luck...
D855 (I think)
Flash tool gives me this every time
This was also not helpfull :/
http://forum.xda-developers.com/showthread.php?p=53796705
Any ideas?
Click to expand...
Click to collapse
Hi there! Do you have the correct .dll and stock version for your phone? Try using a newer version of the flash tool.. I used version 1.8.6.527. Make sure you set COM ( Under "Device Manager" ) to COM 41. Good luck !!! :good:
Showtek1980 said:
Hi there! Do you have the correct .dll and stock version for your phone? Try using a newer version of the flash tool.. I used version 1.8.6.527. Make sure you set COM ( Under "Device Manager" ) to COM 41. Good luck !!! :good:
Click to expand...
Click to collapse
No luck... :crying:
I'm still getting the "Model Information Check FAIL!" Notification.
The Model I'm using is labeled "Not for sale"
I updated the flash tool to verison 1.8.6.527 and checked the COM port to be 41
I'm actually not sure I have the correct .dll and tot-files. Is there a list for them?
Any suggestions
thermopoli said:
No luck... :crying:
I'm still getting the "Model Information Check FAIL!" Notification.
The Model I'm using is labeled "Not for sale"
I updated the flash tool to verison 1.8.6.527 and checked the COM port to be 41
I'm actually not sure I have the correct .dll and tot-files. Is there a list for them?
Any suggestions
Click to expand...
Click to collapse
Make sure of your model number!!! Then post the model number and I'll check online for the correct .dll and tot files.
Go under " Settings, About Phone, Software Information "..
If you can't get into your system .. check your phone package.. On the box, it should have your model number.
https://www.bloglovin.com/blog/post/5233323/3045449639
http://www.mylgphones.com/lg-software-tools-download
http://forum.xda-developers.com/showthread.php?t=2772658
http://www.mylgphones.com/lg-finlan...ve-users-the-choice-of-3gb-or-2gb-of-ram.html
I really hope at least one the links above would assist you man!
Showtek1980 said:
Make sure of your model number!!! Then post the model number and I'll check online for the correct .dll and tot files.
Go under " Settings, About Phone, Software Information "..
If you can't get into your system .. check your phone package.. On the box, it should have your model number.
Click to expand...
Click to collapse
Thanks!
I'm quite certain that it's the D855, at least it says so in the box
Hello
This is the process that I used to unbrick the LG G Pad 8.3 tablet.
Note 1: The operating system on my PC is Windows XP SP3 x86
Note 2: The same process should also work on LG G Pad 10.1 (With a different .tot file)
1. First of all you should make sure that the G Pad is detected when connected to the PC.
The device should be seen as QHSUSB_DLOAD in Other Devices section in Device Manager.
hxxp://i.imgur.com/IawJZq0.jpg
2. Install the QHSUSB Driver for your operating system.
The driver can be found here:
hxxp://mega.nz/#!HlpViaTJ!NPACjSQtTjGWdYIj3kHO3bGfmAotaSSQindmgRY9VJ4
I have used the driver from the "checked" folder.
Reconnect the tablet and you should now see the device as Qualcomm HS-USB QDLoader 9008 (COMxx) under the Ports section in Device Manager.
Take a note of the COM port number.
hxxp://i.imgur.com/IR7uUCB.png
3. Download the .tot image file for you tablet model.
I have used the one from here (LG G Pad 8.3 V500 4.4.2):
hxxp://androidfilehost.com/?fid=23329332407581518
4. Now you need the LG BoardDiag tool.
Download this one from here:
hxxp://mega.nz/#!XwgkXTAR!JnAAXKBQoezT7CcxRSVkSQlPFr4AXcvfm6oJbw4bht4
Please use only this one even if you have another BoardDiag. I have tried other versions and this was the only one that worked. For the other versions I always got some error:
failed during loading flash programmer
or
device not found in dload trying flash programmer
With this tool we will extract the .tot rom image first.
Unrar the archive and open BoardDiag3.99c application.
Click on the ... button next to BIN from the Image Extraction section on the bottom of the BoardDiag application and browse to the .tot file you downloaded at step 3.
Then click on the ... button next to DIR and browse to a folder to extract the files in.
Click on the Extract button and wait for the files to be extracted.
After the extraction is complete, close the BoardDiag application.
hxxp://i.imgur.com/Kw0ZhUv.jpg
5. Now we will perform some cheks on the tablet.
Open the BoardDiag application again.
Now select the AP check and EMMC TEST checkboxes from the Board Diag Test section on the top-left.
Also choose the G-pro (APQ8064) on the AP Chipset dropdown selection box. Choose the Com Port that you took a note of at step 2. Select as the Target Dir the folder where you extracted the .tot image file at step 4. These settings are in the top-right side of the BoardDiag application. Make no other changes to the settings.
Now Click on the big START button and wait for the checks to be made.
If everything is OK you should see under the Test Results section the green text PASS both under the AP and EMMC. Leave the BoardDiag application open. Now you can proceed to step 6.
6. Now we will Flash the files to the tablet.
Now you will also check the SDRAM TEST checkbox on the left top side of the BoardDiag application. The other settings were already made in step 5. Click the START button again.
After performing the checks you should see that the files from the image (aboot.mbn, boot.mbn, etc.) are written to the tablet.
After that, the BoardDiag tried to reset the tablet, but it failed and it ended with FAIL for SDRAM under the Test Results section. But the files were already written on the tablet.
7. After that I disconnected and reconnected the tablet to the PC. Nothing was detected, or so I thought, because I could see that in Device Manager something was happening. It was like refreshing itself every 5 seconds or so. I disconnected the tablet from the PC and I plugged in the wall charger. It turns out that the battery had no power.
After a few minutes the LG logo appeared on the screen. Nothing else was happening but I could see the LG logo. I left the tablet to charge the battery for at LEAST 3 hours. If your tablet battery is also discharged you should plug your tablet to the charger for at LEAST 3 hours.
After that I reconnected the tablet to the PC and it was detected as G Pad but it couldn't find the driver.
8. Install the LG Mobile Drivers.
You can get them from here:
hxxp://mega.nz/#!j8xikSYC!Njz3E1_PSJanzQEeZCbbEoWfxUz9TfrTVgusqBCJ2qY
After the driver installation reconnect the tablet to the PC.
It should now be connected properly.
9. Download LG Mobile Support Tool. You can use the launcher from here:
hxxp://mega.nz/#!bp5jgBQJ!xqiMyQU7z-ATlYz__0ybz2kM7boeLFNgqsu5XoPPSzo
Open LG Mobile Support Tool. You should now see the tablet is connected correctly and you should see the tablet model on the left side of the LG Mobile Support Tool. You will now go to Options and choose Upgrade Recovery. Wait for the image to be downloaded and flashed to the tablet.
After the process is completed the tablet will boot to life again.
Please write your comments bellow if you succeeded or failed. I will provide further assistance if required.
PS: I think you need to remove the battery and reinsert it after step 6. Or it could also work if you let the battery discharge completely.
Good luck!
I could not post the images and the links.
I will add them later (after I get to 10 posts).
Contact me on skype (cyadron) for the files and for other help.
nice finding.
it can be handy if we try to flash the v510 bootloader on the v500 to see if it fits and "unlocks" the pad
ckret said:
nice finding.
it can be handy if we try to flash the v510 bootloader on the v500 to see if it fits and "unlocks" the pad
Click to expand...
Click to collapse
Actually it was the only way I found that worked to unbrick this tablet.
Bricked LG G Pad
Need your help man with those files. I bricked my device after flashing wrong file. I have tried LG G2 Pro Board Diag tool and everything passes except SDRAM.
Thanks in advance for your assistance.
Links for files
Hi, I bricked my GPad and would be very interested in getting the proper files or links. How can I get them?
I will update this thread as soon as I can post links. Hopefully no more than a few days.
cyadron said:
I will update this thread as soon as I can post links. Hopefully no more than a few days.
Click to expand...
Click to collapse
Can you post links ?
This sounds very promising @cyadron, hopefully you'll be able to edit the links in soon.
@muiriddin this sounds like you should be able to revive your tablet from your science experiment.
@fefifofum posting here instead of the other thread as that would be way off topic for it.
This sounds like we'll be able to do some proper experimenting and still be able to recover if it doesn't work!
Hopefully I will be able to post the links soon. Does anyone know the minimum number of posts required to post links?
cyadron said:
Hopefully I will be able to post the links soon. Does anyone know the minimum number of posts required to post links?
Click to expand...
Click to collapse
Just put hxxp instead of h t t p.
roirraW "edor" ehT said:
Just put hxxp instead of h t t p.
Click to expand...
Click to collapse
Thank you. That worked.
Links have been added.
cyadron said:
Thank you. That worked.
Links have been added.
Click to expand...
Click to collapse
This thread should probably be pinned. You can request the moderators to do so by "reporting" your first post and ask them there. Too bad, as far as I know, there aren't any TOTs available for the VK810, although I haven't needed one yet.
I used the tutorial, but accuses ero Emmec test fails
Any solution?
edsmat said:
I used the tutorial, but accuses ero Emmec test fails
Any solution?
Click to expand...
Click to collapse
Unless there is a hardware problem with the emmc, it should work.
Try and remove the battery and put it back again.
Please also make sure you follow the steps as described.
Cluey said:
This sounds very promising @cyadron, hopefully you'll be able to edit the links in soon.
@muiriddin this sounds like you should be able to revive your tablet from your science experiment.
@fefifofum posting here instead of the other thread as that would be way off topic for it.
This sounds like we'll be able to do some proper experimenting and still be able to recover if it doesn't work!
Click to expand...
Click to collapse
It would be nice to get my science experiment working again... I hopefully will have some time to follow this process this weekend...
hi, i have hardbrack v410 no have screen at all only qualcomm hs_usb 9008 please help me (
lgv410 said:
hi, i have hardbrack v410 no have screen at all only qualcomm hs_usb 9008 please help me (
Click to expand...
Click to collapse
Read everything you can and follow instructions.
I think you'll need to search further than just this thread though. I read about someone recovering an LG device from this state but I think it was a phone.
But you'll need to find it and follow the instructions, I don't remember where I read it.
Cluey said:
Read everything you can and follow instructions.
I think you'll need to search further than just this thread though. I read about someone recovering an LG device from this state but I think it was a phone.
But you'll need to find it and follow the instructions, I don't remember where I read it.
Click to expand...
Click to collapse
thank you for you answer, can you show me where i can found this instructions to fix this problem? :/
lgv410 said:
thank you for you answer, can you show me where i can found this instructions to fix this problem? :/
Click to expand...
Click to collapse
No, I'm not here to do searches for you.
It has taken me many days to find a tool to flash KDZ AND TOT since many people show an error at 4% of FlashTool and there is no solution so this is your Post.
LGUP is a tool used by Lg for phones that still have a guarantee such as a system error or a software error.
Compatible with Windows vista/7/8/10 No macOS No Linux
Thanks to DroidTH for giving me a link
ok let's start
Renember: All will be erased in the internal memory.
Your warrantly is now avoid
Visit [How-to] Flash firmware KDZ G2 G3 G4 by LGUP On Youtube to the link
Remember that it is not channel advertising, it's just that I can not add external links
Steps to follow
Make sure you have the drivers installed correctly
Download The KDZ / TOT
Connect Lg g3 to pc (No need to enter download mode manually)
Unzip (LGUP-G2-G3.ZIP)
First install (LGUP_8974_DLL_Ver_0_5_CODEFIRE)
Second Install (LGUP_Install_Ver_1_14_3)
Enter the LGUP program that is probably hosted on your desktop
Select the Upgrade box and select the KDZ / TOT file
Wait for the process to finish (Do not disconnect the phone)
At 80% the phone will restart (not yet to be disconnected)
When you reach 100% the phone must have turned on or starting on the TMO logo
If it does not start
-------------------------------------------------- -------------------------------------------------- ----
If it does not start
---------------------------------------------- -------------------------------------------------- -----
If it restarts constantly and does not enter the system (It restarts before reaching the optimizing application)
Turn off the phone completely and remove the battery
Wait 10 seconds. And put it back
Press Vol- and on when logo is released and press them again.
Give you everything
EYE: all files on the internal SD card will be erased
A factory reset will be made and then it must be turned on normally.
If it still does not start, remove the chip (SIMCARD)
Well that's all if you have any questions please write
Sorry if I needed something, it's just that I'm new and I do not know anything about xda
I hope you understand.
When I run LGUP it says Model is Unknown, then gives an error telling me I have to choose a known Model. Drivers are installed, USB debugging is enabled, not sure what else there is missing. Please help.
my phone: (T-Mobile lg g3 d851 30e)
dricialg said:
error Unknown model.!!
my phone: (g3 d851 30e)
Click to expand...
Click to collapse
sorry you had problems
the error is one of the drivers lg
you should plug it into one of the main USB ports on your PC.
or rather entering device manager and re-assign drivers to ports.
Have you downloaded the lgup for lg g3 and g2?
Drivers are installed, USB debugging is enabled, LG PC Suite OK.not sure what else there is missing.
Download : lgup-g2-g3.zip
Solve it FIX
good after I found the problem LGUP
roms apparently change the model of the device as it changes cm11 to build Cyanogenmod 11 xx
AOSP - to AOSP rom 2 etc.
the solution would be to install a stock rom clean no matter if v10 v30 etc. The important thing is not having changed the model number and manufacturer.
I hope I have helped and sorry
that includes cloudy fa's roms
minicm94123 said:
It has taken me many days to find a tool to flash KDZ AND TOT since many people show an error at 4% of FlashTool and there is no solution so this is your Post.
LGUP is a tool used by Lg for phones that still have a guarantee such as a system error or a software error.
Compatible with Windows vista/7/8/10 No macOS No Linux
Thanks to DroidTH for giving me a link
ok let's start
Renember: All will be erased in the internal memory.
Your warrantly is now avoid
Visit [How-to] Flash firmware KDZ G2 G3 G4 by LGUP On Youtube to the link
Remember that it is not channel advertising, it's just that I can not add external links
Steps to follow
Make sure you have the drivers installed correctly
Download The KDZ / TOT
Connect Lg g3 to pc (No need to enter download mode manually)
Unzip (LGUP-G2-G3.ZIP)
First install (LGUP_8974_DLL_Ver_0_5_CODEFIRE)
Second Install (LGUP_Install_Ver_1_14_3)
Enter the LGUP program that is probably hosted on your desktop
Select the Upgrade box and select the KDZ / TOT file
Wait for the process to finish (Do not disconnect the phone)
At 80% the phone will restart (not yet to be disconnected)
When you reach 100% the phone must have turned on or starting on the TMO logo
If it does not start
-------------------------------------------------- -------------------------------------------------- ----
If it does not start
---------------------------------------------- -------------------------------------------------- -----
If it restarts constantly and does not enter the system (It restarts before reaching the optimizing application)
Turn off the phone completely and remove the battery
Wait 10 seconds. And put it back
Press Vol- and on when logo is released and press them again.
Give you everything
EYE: all files on the internal SD card will be erased
A factory reset will be made and then it must be turned on normally.
If it still does not start, remove the chip (SIMCARD)
Well that's all if you have any questions please write
Sorry if I needed something, it's just that I'm new and I do not know anything about xda
I hope you understand.
Click to expand...
Click to collapse
Where are downloads
minicm94123 said:
good after I found the problem LGUP
roms apparently change the model of the device as it changes cm11 to build Cyanogenmod 11 xx
AOSP - to AOSP rom 2 etc.
the solution would be to install a stock rom clean no matter if v10 v30 etc. The important thing is not having changed the model number and manufacturer.
I hope I have helped and sorry
Click to expand...
Click to collapse
Hi !
How do I do all the above ?
My PC recognize the phone without problem, but LGUp won't start unless I "select a known model"... (LGUp window shows : Model = Unknown ; COM Ports = [COM5, CloudyG3] )
Problem is that my phone is softbricked after installing a new ROM, and I can only enter download mode (not even recovery). I just want to downgrade it and reflash a LG's stock ROM (or whatever ROM that would make my phone actually work !!! )
Can you help me do that ?
raf1978 said:
Hi !
How do I do all the above ?
My PC recognize the phone without problem, but LGUp won't start unless I "select a known model"... (LGUp window shows : Model = Unknown ; COM Ports = [COM5, CloudyG3] )
Problem is that my phone is softbricked after installing a new ROM, and I can only enter download mode (not even recovery). I just want to downgrade it and reflash a LG's stock ROM (or whatever ROM that would make my phone actually work !!! )
Can you help me do that ?
Click to expand...
Click to collapse
Do you still wanting help?
minicm94123 said:
Do you still wanting help?
Click to expand...
Click to collapse
YEEEESSSSSS !!!!
Please.... ?
(My phone is currently used as a toy by my 6 yo daughter ? )
LGUP "UNKNOWN" and FlashTool failure with LG G3 (and possibly others)
When I downloaded and installed LGUP with the DLL installer stated to be for the LG G3, the program did not recognise the phone, reporting it as "UNKNOWN". The LG FlashTool also failed, reporting the IMEI and PID as NULL. After spending a lot of time on this, I twigged that the DLL file in the LGUP model directory was for the 8994 processor; but the G3 has an 8974, quite different and incompatible. I located the DLL installer MSI file for 9874 devices, uninstalled LGUP and the DLLs from Windows add/remove programs, ran the 9874 DLL installer and reinstalled the LGUP program, and everything worked.
The file is, amongst other places, on https://uptoandroid.com/download-lg-up-tool-for-lg-smartphone-latest/. Do not download DLL files for LG G4, LG V10, LG G3, LG Stylo, filename LGUP_Common_DLL_Ver_1_0_28_5 .msi, but instead For LG phones based on Qualcomm Snapdragon 800 MSM8974 SoC, filename LGUP_8974_DLL_Ver_0_5.msi:.
HTH
23 Aug 19: I find that I've rediscovered the wheel. Exactly what I said was posted in 2016 - if I'd found it, it would have saved me a lot of time!
okay let start, my friend gave me his LG G4 with BOOT LOOP issue.
so i did like in the video
https://www.youtube.com/watch?v=TM9umec5aeo
the phone worked for 5 hours and back to boot loop issue. so in this time i made backup.
after it i follow this guide
https://forum.xda-developers.com/g4/development/ilapo-infinite-loop-auto-power-off-fix-t3404421
but the friend phone has marshmallow android and i need lollipop android so i have flashed wrong ktz by mistake and phone gone to Brick mode.
so i search a lot in the internet MBN file for G4 and i found so i want to share it with you
just download the files from next linkaccording to your model
http://bit.ly/2maK3uL
or
Code:
http://forum.gsmdevelopers.com/showthread.php?t=24303
the password for H815 is "Moyal Software H815",for other just PM to dev.
after i downgraded to android 5.5 i continue with
https://forum.xda-developers.com/g4/development/ilapo-infinite-loop-auto-power-off-fix-t3404421
and after it i reactive the reset cores with kernel adiutor.
right now the phone works well already 4 days.
Enjoy.
These are the exact same files as already given in another thread. They don't work for me.
Depending on QFIL version I have "Device not in firehose mode" or "too long to open COM port" error.
I have H815. Bricked the exact same way as yours.
Do you have any ideas what I can change/try?
Dear,
I have the same problem with a H818P.
Someone can help me!?
I`ve attached a screenshot with my problem!
https://ibb.co/hVthyv
I`m stuck in "COM Port number 5"
in device manager, is not possible to find "Qualcomm MMC Storage USB Device" under disk drivers.
thanks!
rfsaidel said:
Dear,
I have the same problem with a H818P.
Someone can help me!?
I`ve attached a screenshot with my problem!
https://ibb.co/hVthyv
I`m stuck in "COM Port number 5"
in device manager, is not possible to find "Qualcomm MMC Storage USB Device" under disk drivers.
thanks!
Click to expand...
Click to collapse
Hey, I have struggled long time with this but finally I got it to work
I used this guide:
http://gsmmarhaba.com/threads/unbrick-lg-g4-brick-hs-usb-qdloader-9008-without-box.612/
But instead files for H815 i used ones for LS991 and QPST 2.7.425. Files were flashed successfully and now I have download mode
So try with other versions of mbn files as well as with other versions of QPST/QFIL. Good luck.
washoq said:
Hey, I have struggled long time with this but finally I got it to work
I used this guide:
http://gsmmarhaba.com/threads/unbrick-lg-g4-brick-hs-usb-qdloader-9008-without-box.612/
But instead files for H815 i used ones for LS991 and QPST 2.7.425. Files were flashed successfully and now I have download mode
So try with other versions of mbn files as well as with other versions of QPST/QFIL. Good luck.
Click to expand...
Click to collapse
Thank you ! I'll try this and will send a message with final result.
I can Help
washoq said:
These are the exact same files as already given in another thread. They don't work for me.
Depending on QFIL version I have "Device not in firehose mode" or "too long to open COM port" error.
I have H815. Bricked the exact same way as yours.
Do you have any ideas what I can change/try?
Click to expand...
Click to collapse
I have a solution, BTW have you solved your issue
washoq said:
Hey, I have struggled long time with this but finally I got it to work
I used this guide:
http://gsmmarhaba.com/threads/unbrick-lg-g4-brick-hs-usb-qdloader-9008-without-box.612/
But instead files for H815 i used ones for LS991 and QPST 2.7.425. Files were flashed successfully and now I have download mode
So try with other versions of mbn files as well as with other versions of QPST/QFIL. Good luck.
Click to expand...
Click to collapse
Dear Washoq!
The mega.nz link (provided on the page you shared) is expired. Can you please upload the files yourself and share them here?
For fusing devices h815, to get download mode
https://mega.nz/#F!GJ9WlCYA!IT57novfFmId67gUt7_QPQ
Pleas bro all links are broken pleas update