Hi there,
I just updated P8000 via OTA update and after downloading the Update, the phone restarted and stops at the elephone boot Logo (about 30 min )!!
I did 5 Restarts but every time it hangs at the boot logo...
In the past i did no other updates or flashing ROMS.. nothing!
When i press "Volume Up" and "Power" to Start, i get three Options:
Recovery Mode
Fastboot Mode
Normal Boot
Using Recovery Mode leads to: Symbol Android Robot with "No Order" (in german : "Kein Befehl")
Using Fastboot Mode leads to: Nothing (Recovery Menue stays)
Using Normal Boot leads to: restart and hanging at Elephone Boot Logo
So, I am running out of Options... any ideas?
Cheers, Albert
Same. I tried using the official instructions to flash the stock rom but the SP flash tool stops responding after download button is pressed
a.cid said:
Same. I tried using the official instructions to flash the stock rom but the SP flash tool stops responding after download button is pressed
Click to expand...
Click to collapse
The Hardware of P8000 is pretty cool, but the Software is "§$§"%§""!$%
When you go to recovery mode and get the the android robot symbol. Press again Vol up + Power until you enter to recovery. Make a 3 wipe (data factory , cache and dalvink). Reboot and uninstall the El loader. Use another Loader instead of El Loader
i had the same problem. (in English NO COMMAND) I only flash Eragon ROM again. Sometimes you have to repeate.
AL 6677 - ELEPHONE MUST BE TURN-OFF !!!!!!! and CONNECT USB CABLE REPEATEDLY !!!
After that everything goes according to instructions
https://translate.google.at/transla...-p8000-rooten-und-flashen/&edit-text=&act=url
same problem since OTA my phone is bricked and cant unbrick
neonero said:
When you go to recovery mode and get the the android robot symbol. Press again Vol up + Power until you enter to recovery. Make a 3 wipe (data factory , cache and dalvink). Reboot and uninstall the El loader. Use another Loader instead of El Loader
Click to expand...
Click to collapse
THX a lot, I found only the 2 Options to wipe data factory and cache....... dalvink was not displayed in the menue (screenshot attached)
How to uninstall the EL Loader ?
showshow747 said:
i had the same problem. (in English NO COMMAND) I only flash Eragon ROM again. Sometimes you have to repeate.
AL 6677 - ELEPHONE MUST BE TURN-OFF !!!!!!! and CONNECT USB CABLE REPEATEDLY !!!
After that everything goes according to instructions
THX, I will try to flash Eragon, CM 12.1 is still not available, isn't it?
Click to expand...
Click to collapse
No CM 12.1 is not available yet.
In order to uninstall EI Loader, install first root (superSU), then install ccleaner and you can uninstall EI Loader (In system app)
Hi there, sorry for the revival !
But i got the same problem: OTA update, fail, P8000 blocked on boot screen.
I tried wipe data/factory reset + wipe cache -> nothing changed, still boot screen blocked...
Then, i tried to use flash tool, but, the phone isn't booting, so my pc isn't recognizing the phone..
I'm not even sure that I correctly installed the drivers..
Can i use flash tool even if the phone is blocked to boot screen?
I downloaded this ROM: stock-rom-elephone-p8000-20150907-android-5-1 (this is my first post i can't post URL..)
Because i got some issues with my phone and support told me to try it.
But when i follow the tutorial, launching "donwload" and connecting the phone, nothing happening..
The phone turn on, and display recharging logo, and flash tool still wainting.
Recovery mode -> "No command", Volume up + power is working, i used it to wipe datas
But at the moment, i'm still blocked, since 2 days, i dont know what to do
Can someone help me?
Thank you by advance, i hope my english isn't so bad
Zywoon said:
Hi there, sorry for the revival !
But i got the same problem: OTA update, fail, P8000 blocked on boot screen.
I tried wipe data/factory reset + wipe cache -> nothing changed, still boot screen blocked...
Then, i tried to use flash tool, but, the phone isn't booting, so my pc isn't recognizing the phone..
I'm not even sure that I correctly installed the drivers..
Can i use flash tool even if the phone is blocked to boot screen?
I downloaded this ROM: stock-rom-elephone-p8000-20150907-android-5-1 (this is my first post i can't post URL..)
Because i got some issues with my phone and support told me to try it.
But when i follow the tutorial, launching "donwload" and connecting the phone, nothing happening..
The phone turn on, and display recharging logo, and flash tool still wainting.
Recovery mode -> "No command", Volume up + power is working, i used it to wipe datas
But at the moment, i'm still blocked, since 2 days, i dont know what to do
Can someone help me?
Thank you by advance, i hope my english isn't so bad
Click to expand...
Click to collapse
Yes you can use SPFlash tool evenif the phone stucks in the boot screen. Simply switch the phone off, start SPFlash tool and then connect the phone to usb.
If you follow the instructions from elephone, then your phone should working again: http://bbs.elephone.hk/thread-1037-1-1.html#.VofQ13wvdpo
Cheers
Hi, and thx for the help.
The driver is correctly installed now, i had to allow unsigned drivers in windows parameters.
So, i followed the tutorial, again.
I configured SP flash tool, clicked download, and then connected powered off P8000 with USB.
But, again, the phone displays recharging logo, and flash tool still waiting...
The phone is recharging so the USB is working, so i don't know how to make my PC detect the phone......
Is there a way or a thing that i missed?
thank you..
EDIT: i finally got a timeout error from flashtool..
I missed something, but what !? i can't remove P8000 battery, is there somthing to do to get it detected by windows?
Like a boot mode, or a magic formula... i'm open
For MTK Driver installation:
Did you follow skeletons Guide? http://forum.xda-developers.com/elephone-p8000/help/guide-windows-10-mtk-vcom-usb-drivers-t3264884
I'm sorry to say, that I do not have any experience with windows installation, this problem, because SPFlash tool performes on my 64bit Linux very well, without any driver trouble.
Cheers
Hi,
I'm on windows 8.
I used SP_driver_v2.0, that is an .exe
it's the only driver tips gived in most of tutorial
I allowed unsigned drivers installation, and i correctly installed it.
I tried too use flashtool before and after restarting the PC-> no changes
Flashtool doesnt detect the phone
I start getting crazy..
I have repaired mine, so i'll share
Al6677 said:
Hi there,
I just updated P8000 via OTA update and after downloading the Update, the phone restarted and stops at the elephone boot Logo (about 30 min )!!
I did 5 Restarts but every time it hangs at the boot logo...
In the past i did no other updates or flashing ROMS.. nothing!
When i press "Volume Up" and "Power" to Start, i get three Options:
Recovery Mode
Fastboot Mode
Normal Boot
Using Recovery Mode leads to: Symbol Android Robot with "No Order" (in german : "Kein Befehl")
Using Fastboot Mode leads to: Nothing (Recovery Menue stays)
Using Normal Boot leads to: restart and hanging at Elephone Boot Logo
So, I am running out of Options... any ideas?
Cheers, Albert
Click to expand...
Click to collapse
So the simple way to solve it is flashing the latest stock elephone p8000 ROM, which you can find on google easly
1. as described on other forums, you have to install the adnroid drivers, then get the sp flash tool, and have an un-zipped stock elephone p8000 ROM.
2. if you are stuck at bootloop, do the following to power off the phone so you can flash the ROM
1. Long press power button until power off
2.Do it fast--Press volume Up and then hold power button
3. choose recovery (volume up choose menu, volume down enter)
4. android logo with red triangle is displayed( "no command")
5. hold power button and press volume up
You're in recovery mode
3. select power off
4. open the SP flash tool >go to download tab>opne "scatter loading"( you will find it in the Folder where you unzipped the stock elephone p8000 ROM, if you have more folders there, chose "firmware" folder)
5. on the left side, under scatter loading, you will find a "pull-down" tab - it will be written "download" chose "firmware upgrade" or "upgrade"
6. start the process, then connect your elephone p8000 (it must be powere off) via usb cable to the PC, the process will start,and in less then 5 Minutes you have a factory new Elephone p8000 with the latest good update
7. WATCH OUT- it will erase all your data, absolutely all your data on the phone, except SIM and SD card.
Hope it helped, if not, feel free to ask me =)
Hello,
I have similar problem. Bought P8000 5 days ago. Did update today. Bricked. Stuck at logo ... I tried to flash but SP flush tool but the process isn't starting. When I downloaded ROM I received long list as on the screenshot: kaczorowscy.name/Screenshot.png
I have ubuntu - I see lsusb and dmesg see the phone (it is shut down from recovery menu) but maybe I am missing something ....
Ok here is what id did:
1. Get SP flashtool
2. get newest stock ROM
3. Shut down phone through android recovery menu (start phone with holding volume up, select recovery mode, wait for dead android, hold volume up and unblock button for 3 sec.)
4. Open SP flashtool - use "format all + download" of ROM (unzip and select scatter file from rom) - click start
5. Connect shut downed phone
6. Dot OK! from flashtool
PS. Flashing removed IMEIs - they are both written on the battery - you need to use android service menu to check them with special codes and reboot the phone.
Thanks ALL! :good:
Fix - Recovery Mode
Al6677 said:
Hi there,
I just updated P8000 via OTA update and after downloading the Update, the phone restarted and stops at the elephone boot Logo (about 30 min )!!
I did 5 Restarts but every time it hangs at the boot logo...
In the past i did no other updates or flashing ROMS.. nothing!
When i press "Volume Up" and "Power" to Start, i get three Options:
Recovery Mode
Fastboot Mode
Normal Boot
Using Recovery Mode leads to: Symbol Android Robot with "No Order" (in german : "Kein Befehl")
Using Fastboot Mode leads to: Nothing (Recovery Menue stays)
Using Normal Boot leads to: restart and hanging at Elephone Boot Logo
So, I am running out of Options... any ideas?
Cheers, Albert
Click to expand...
Click to collapse
When I was trying to root my p8000 I couldn't flash a custom recovery, fortunately I discovered that to access recovery on stock android you need to go to the screen with the android and "no command"/"no order" text and hold down Vol+Up and Power for 3~ seconds and then release power, this will boot you into recovery mode, If wiping cache/factory reset isn't enough "fastboot flash recovery <image>.img" SHOULD work now
hope this helped
I was provided this device to try and help resolve the issue. I am not sure how it got to this point. I believe that it was rooted with a custom ROM, then the individual tried to install a stock ROM (method unknown).
The current situation is:
Galaxy Tab S 10.5 SM-T800 stuck in a bootloop with the TWRP logo on the screen. I can not get the tablet to go into download mode. I have tried all of the different methods to enter download mode, i.e. Power & Vol - & Home, Drain the battery > Plug into PC while holding Vol - & Home, Power & Vol + & Vol -. None of these combinations do anything. The only thing I can do to get a response is to press Power & Vol +, which reboots the device right back into the TWRP loop after the Samsung Logo. Power button alone does nothing.
The device is seen by Windows with the Samsung Drivers but is not mounted to a drive letter, and I can not mount it.
ADB , fastboot and Odin do not see the device.
I would like to flash a new rom either custom or stock, but I need to be able to get the device into download mode so it can be seen by odin.
Any help would be great.
Mike
Probably just timing and pilot error this one. I've never known of any Samsung device boot but be incapable of booting to download mode as download mode is bootloader related.
No working bootloader means dead device.
No matter what state the device is in at the moment with the usb cable removed, hold POWER + VOL DOWN (not up) + HOME until the Samsung boot logo comes up, hold for another couple of seconds then release. Download mode should appear.
I know it should be easy....
I know it should work but it is not, I will make a vid of the process and post. I can not make heads or tails.
Mike
ashyx said:
Probably just timing and pilot error this one. I've never known of any Samsung device boot but be incapable of booting to download mode as download mode is bootloader related.
No working bootloader means dead device.
No matter what state the device is in at the moment with the usb cable removed, hold POWER + VOL DOWN (not up) + HOME until the Samsung boot logo comes up, hold for another couple of seconds then release. Download mode should appear.
Click to expand...
Click to collapse
Is the home button actually working, are you pressing it firm enough?
If the home button doesn't register then the tablet will simply reboot.
Its a bit odd why twrp doesn't fully boot though unless it's the wrong one.
Does it hang at the twrp logo or continually reboot?
I have three (3) Samsung Galaxy Tab Kids T2105 tablets. All are running the latest firmware, T2105UEAOE1.
None of them will boot into recovery. The tabs work, they will boot normally, and then will boot into Download mode. But they will not boot into recovery.
* If I hold down Power+VolUp+Home, or Power+VolUp, continuously, the Tab turns on, and then, about 5 seconds later, turns back off.
* If I hold down Power+VolUp+Home, or Power+VolUp, and release them when the Samsung Logo appears, the device boots normally.
* If I hold down Power+VolUp+Home, or Power+VolUp, and release Power when the Samsung Logo appears, and then continue to hold VolUp and/or Home, the device sits on the Samsung Logo for 20 seconds, then the screen goes blank for a second, then the logo comes back on and sits for 20 seconds, then the screen goes blank... and this cycle repeats until I release the buttons, at which point the device boots normally.
I have done factory resets (through the normal mode settings menus). I have reflashed the latest firmware with Odin3. Nothing seems to fix this problem.
I've been searching the net for hours for this. I see a number of other people who have reported this problem. But nobody has offered a solution. One person stated that he uses "adb reboot recovery" - which is a fine, if ugly, hack - but the fact remains that, for many people, apparently, Stock Android Recovery is not accessible from the Samsung Galaxy Tab Kids T2105.
Does anyone know of an actual solution for this, to restore recovery functionality to this tablet?
Hello,
I have the same tablet, same problem (no stock recovery). None of the button combinations work, and the logo just keeps repeating. My situations is that my 9 yr old daughter locked herself out and can't remember her lock screen password. It's a totally stock tablet (never been rooted or flashed). Because I can't get into the tablet, I'm not sure what firmware version it has, and it does not have USB debugging enabled.
I tried booting into the stock recovery to do a factory reset (since we can't do it in the Settings). I tried flashing the same firmware you mentioned using Odin. It goes through the motions successfully and reboots. But it boots back to the lock screen and its still "locked" (we still see her personal wall paper) - which tells me the flash is not taking. Even though my Odin set up is fine, it does not work (even though everything passed with green lights). I tried going into Safe Mode to try bypassing the lock screen, but even in Safe Mode it still asks for the password. My thinking was to go into Settings and initiate a new password or do a factory reset.
(BTW - the Safe Mode button combination was different for me. Holding Power + Volume Up did not work. Instead I had to hold Power + Volume Up & Down until the logo showed up. Once the logo disapeared, then I had to let go of the Power button only - but continue holding the Volume Up & Down until it fully booted into Safe Mode).
I tried ADB in order to use a password reset/erase command line. But because the USB debugging is not enabled, ADB doesn't see the tablet. There is no other way to enable it via Odin or ADB. And I can't even sideload any Lock Screen Hack apps becuase the table is not rooted, or not USB debugging enabled, or can't get into recovery to flash an .apk or image.
So I am stuck. Why would Samsung block recovery mode??? I have been trying for more than 8 hours. If anyone can help, me and my 9 yr old daughter will greatly appreciate it. My last attempt will be to try Google Device Manager and see if it can somehow unlocks it. Or try Kies (although everything I have read so far says that these have not worked either).
HELPPPPPPPPPP!!!!!!!
ggee
wfire said:
I have three (3) Samsung Galaxy Tab Kids T2105 tablets. All are running the latest firmware, T2105UEAOE1.
Does anyone know of an actual solution for this, to restore recovery functionality to this tablet?
Click to expand...
Click to collapse
Hello,
I'm not sure which one of these did the trick for me, but I was able to get into recovery mode. I'm not sure if your three tables are rooted or not, but I don't think it matters. Try these two methods:
Method #1:
Technically, I think I just stumbled on to this one after successfully completing Method #2 (below). But it's worth trying it first before moving on to Method #2.
-Hold the Home + Volume Up + Power buttons together at the same time (just like the normal process).
-Now, you will probably need to try this next step a couple of time before you get it right. This is because it happens pretty fast and you need to time it perfectly.
-Notice that when the screen turns on, the actual first thing that happens is that the the screen backlight turns on and glows first. This happens first and a split second later the first Samsung logo flashes.
-You need to let go of all three buttons at the same time as soon as you see the backlight turn on, but before the Samsung logo flashes.
This is the sweet spot, and it happens pretty fast. But once you do it at the right time, the tablet will go black again and then the recovey mode will show up. It works for me every time.
Method #2:
I thought somehow the recovey mode portion of the firmware had become corrupter somehow. So I decided to flash a custom recovery using Odin (since at that time I hadn't stumbled onto Method #1 yet). Make sure to use gr8nole's custom recovery version for the SM-T210 and SM-T210R (these are the equivalent wifi versions of our Kids tablet). His versions have fixed some known bugs that CWM/TWRP have with the wifi version of our tablets. Make sure to download and flash the CWM or TWRP .tar file for Odin (I personally have always liked CWM over TWRP).
Here is his link: http://gr8nole.blogspot.com/
Also mentioned here: http://forum.xda-developers.com/showthread.php?t=2437219
-Make sure you have all the correct USB drivers for the tablet installed on your computer.
-Open Odin and load the .tar file that you downloaded from gr8nole into the PDA or AP slot (depending on your Odin version).
-Let Odin check the m5d verification for successful authorization.
-Once Odin is ready, then boot the tablet into Download Mode (Home + Volume Down + Power button)
-Connect the table to a USB cable that is attached to your computer's main USB port.
-Odin should now recognize that the table it connected to a valid COM port.
-Click <Start> button on Odin and it should flash the costum recovey .tar file pretty quickly.
-The tablet will simultaneously flash a progress bar and start to automatically reboot (also pretty quickly).
-Disconnect the tablet from the USB cable now.
If the tablet does not automatically reboot to the new custom recovery screen, then just power off the tablet completely. Wait 30 seconds, and then boot the table to recovery mode use the Method #1 shown above. You should now be able to go into the new custom recovery mode you flashed with Odin (CMW or TWRP). It should all work now.
From this point you can download and install SuperSU to add root (if you want to).
Let me know if this works for you.
ggee
Hello,
my wife got a S21 FE (SM-G990B/DS VD2). Yesterday it started to reboot over and over out of a sudden, showing the samsung logo first, followed by the knox logo, then shutting off and on again. Tried several guides to enter Recovery or Download Mode. The only thing that worked was entering download mode by pressing Vol up, down and power while a USB-Cable is plugged in, but as soon as i press the vol up button to pass the "warning screen", it shows some phone specs for a couple of seconds, shuts off and starts bootlooping again. After some hours, the phone once entered recovery mode when it lied next to me for about an hour. Tried to wipe cache, but just got an error I can't remember right now. Hoped it fixed itself when it made it to recovery and just rebooted to see if it works again, but then it just keept bootlooping again.
Since then I couldn't figure out why it once booted to recovery on it's own nor why I can't force it to enter recovery by pressing vol up + on.
Still hope it's just a faulty update or bug, but feels very much like it's a hardware related issue. Replacing the phone won't be an issue, but I'd really want to save data on the phone as my wife didn't make any backups and really wants to keep the photos.
As I just found guides that included recovery or DL-Mode, which are both no valid options for my case, I'd be thankful for any ideas to fix the phone or at least gain access to files before replacing it.
So.. did anyone come across similar issues and found a solution to revive the phone or are there any "unpopular" ways to recover samsung phones out of this state?
Edit:
Turned off completely overnight, booted once to system, looped again and now it's working like nothing ever happened. Got no clue what caused it or why it is working again. Saved everything for the case it happens again.
Wouldn't trust that device anymore, but my wife wants to keep it.
¯\_(ツ)_/¯
I would just like to reply here and add my own potential fix and also would like confirmation that it would work.
So I have a SM-G996B in a boot loop which returns a 'fs_mgr_mount_all' error. Possible to reboot into recovery mode, cleared cache and restarted bootloader etc with the same boot loop. Powered off and connected to PC for Download mode for ODIN recovery but upon pressing volume up, it then restarts again so Download mode recovery is impossible.
I know however that Developer options and USB debugging was enabled on the device as well as unlocked boot loader. I was able to download the correct original stock OS based on the PDA , CSC and Android version.
I have then installed the latest ADB software on my PC and Samsung USB drivers.
By then rebooting into recovery mode, I have the option of 'Apply update from ADB'. I have then confirmed the device connects using the ADB devices command.
I would like to clarify one thing however. I want to keep the user data at all costs. By using the stock firmware and renaming as update.zip, will it use the HOME_CSC and not the CSC file? If not would it work if I open the zip and remove the CSC before re-zipping to make sure?
Thanks
Reebee said:
Hello,
my wife got a S21 FE (SM-G990B/DS VD2). Yesterday it started to reboot over and over out of a sudden, showing the samsung logo first, followed by the knox logo, then shutting off and on again. Tried several guides to enter Recovery or Download Mode. The only thing that worked was entering download mode by pressing Vol up, down and power while a USB-Cable is plugged in, but as soon as i press the vol up button to pass the "warning screen", it shows some phone specs for a couple of seconds, shuts off and starts bootlooping again. After some hours, the phone once entered recovery mode when it lied next to me for about an hour. Tried to wipe cache, but just got an error I can't remember right now. Hoped it fixed itself when it made it to recovery and just rebooted to see if it works again, but then it just keept bootlooping again.
Since then I couldn't figure out why it once booted to recovery on it's own nor why I can't force it to enter recovery by pressing vol up + on.
Still hope it's just a faulty update or bug, but feels very much like it's a hardware related issue. Replacing the phone won't be an issue, but I'd really want to save data on the phone as my wife didn't make any backups and really wants to keep the photos.
As I just found guides that included recovery or DL-Mode, which are both no valid options for my case, I'd be thankful for any ideas to fix the phone or at least gain access to files before replacing it.
So.. did anyone come across similar issues and found a solution to revive the phone or are there any "unpopular" ways to recover samsung phones out of this state?
Edit:
Turned off completely overnight, booted once to system, looped again and now it's working like nothing ever happened. Got no clue what caused it or why it is working again. Saved everything for the case it happens again.
Wouldn't trust that device anymore, but my wife wants to keep it.
¯\_(ツ)_/¯
Click to expand...
Click to collapse
Similar issue with same phone. In a bootloop after trying to root. None of the button combinations have worked for me, for the past several days.
Tried powering the phone off for the whole night.
When connected to the PC shows phone is in recovery mode via adb (blank screen though).
Want to know how to get into DL-mode, guaranteed.
Got to DL mode by pressing vol up + down + power + usb cable connected in PC and phone. However, couldn't do anything there, but maybe you can
Also, phone is still working and I still have no clue what was the problem and what fixed it.