i had my s3 i747m on cm13. i was having a lot of problems with bluetooth. so i tried going back to stock firmware and i bricked my phone. i can still access download mode.
with odin running as admin or not, this is what it says when i try to install stock rom in download mode:
ODIN MODE
PRODUCT NAME: SGH-I747M
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOADER RP SWREV: 2
SW REV CHECK FAIL : Fused 2 > Binary 0
i've tried looking for solutions, but all say the same thing...which is to use odin and install the stock rom file.
i had twrp recovery installed if that helps.
sal82 said:
i had my s3 i747m on cm13. i was having a lot of problems with bluetooth. so i tried going back to stock firmware and i bricked my phone. i can still access download mode.
with odin running as admin or not, this is what it says when i try to install stock rom in download mode:
ODIN MODE
PRODUCT NAME: SGH-I747M
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOADER RP SWREV: 2
SW REV CHECK FAIL : Fused 2 > Binary 0
i've tried looking for solutions, but all say the same thing...which is to use odin and install the stock rom file.
i had twrp recovery installed if that helps.
Click to expand...
Click to collapse
can you re-flash twrp recovery?
ethanchow said:
can you re-flash twrp recovery?
Click to expand...
Click to collapse
OMFG!! thank you!! it's working again with cm13! i was pulling my hair out lol.
i just reflashed twrp with odin and it started to work. i guess it was just the recovery files damaged?
sal82 said:
OMFG!! thank you!! it's working again with cm13! i was pulling my hair out lol.
i just reflashed twrp with odin and it started to work. i guess it was just the recovery files damaged?
Click to expand...
Click to collapse
Yes, sometimes stock images won't flash because the bootloader version is lower than the one you have.
Related
So I recently bought a galaxy s3 from a friend and tried rooting it today, but something went horribly wrong and it won't work.
It tells me "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again." I have tried doing that and I can not get it to work. The phone won't even connect to Kies... HELP
This is what it says at the top of the screen.
ODIN Mode
Product name: SPH-L710
Custom Binary Download: Yes (1 counts)
Current Binary: Custom
SYSTEM STATUS: Official
Dualcomm Secureboot: Enable
Warranty Bit: 0
Bootloader RP SWREV: 1
PLEASE HELP SOON!!!
Root/Recovery via ODIN stuck at recovery.img push
Jezdan said:
So I recently bought a galaxy s3 from a friend and tried rooting it today, but something went horribly wrong and it won't work.
It tells me "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again." I have tried doing that and I can not get it to work. The phone won't even connect to Kies... HELP
This is what it says at the top of the screen.
ODIN Mode
Product name: SPH-L710
Custom Binary Download: Yes (1 counts)
Current Binary: Custom
SYSTEM STATUS: Official
Dualcomm Secureboot: Enable
Warranty Bit: 0
Bootloader RP SWREV: 1
PLEASE HELP SOON!!!
Click to expand...
Click to collapse
Bump!
I am using the GS3 Toolkit v7.5.1 on a Sprint SPH-L710 totally stock untouched ROM.
I kinda made an alteration by adding the TWRP Recovery v2.6.3.1 for this Sprint GS3 variant, and renamed it to the TWRP recovery included with the Toolkit i.e. TWRP 2.5.0.0
Now while going through the Root/Recovery (ALLINONE) option, when Odin comes up, it sends the boot.img fine, but is now stuck on sending down recovery.img.
But I don't know enough about Odin or the GS3, to know if I can just shut down Odin, and it'll trigger the phone to reboot and I can not be sneaky, replace the original recovery, and try again?
This is what my phone says on the "Downloading..." screen
Code:
[COLOR="Red"][B]ODIN Mode[/B][/COLOR]
Product name: SPH-L710
Custom Binary Download: [B][COLOR="Green"]No[/COLOR][/B]
Current Binary: SAMSUNG Official
SYSTEM STATUS: Official
Qualcomm Secureboot: ENABLE
Can I shut down Odin, and manually reboot the phone to the Download mode, and repeat the process?
PLEASE Help!
Hi Guys,
I have an unlock code from AT&T and I want to use it from the Stock ROM. I am currently running CM 11 nightlies.
I tried the standard method of using ODIN from PC to flash stock ROM. It doesnt seem to work. I am always stuck in ;NAND write Fail'.
Before installing CM a while ago I updated OTA to 4.3, and based on what I read everywhere this seems to have something to do with the issue.
Any help on how to proceed will be great.
I am using ODIN 3.07
Downloaded Stock ROM from sammobile.
This is what my download screen reads.
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: Yes (2 Counts)
CURRENT BINARY: CUSTOM
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOADER AP SWREV: 2
SW REV CHECK FAIL: Fused 2 > Binary 0
Thanks!
Once you have the 4.3 bootloader, you cannot use Odin to install a stock AT&T ROM. You can try this: http://forum.xda-developers.com/showthread.php?t=2658486
audit13 said:
Once you have the 4.3 bootloader, you cannot use Odin to install a stock AT&T ROM. You can try this: http://forum.xda-developers.com/showthread.php?t=2658486
Click to expand...
Click to collapse
Thanks! I will take a look. Hopefully I can unlock my device at some point.
Was able to unlock based on the lead from post #2
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
mtsosie said:
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
Click to expand...
Click to collapse
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Ok, so I also wasn't able to get into recovery.
I decided to flash cwm via odin. After it flashed the phone rebooted and turned on normally. I have turned it on and off like 5 times and everytime it boots normal.....But, there is still a problem... baseband version is Unknown and there is no IMEI Number.
Larry2999 said:
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Click to expand...
Click to collapse
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
mtsosie said:
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
Click to expand...
Click to collapse
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Larry2999 said:
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Click to expand...
Click to collapse
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
mtsosie said:
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
Click to expand...
Click to collapse
You are most welcome. Glad to know it's now working.
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
dark_darkness said:
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
Click to expand...
Click to collapse
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
can u share a link?
Larry2999 said:
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
Click to expand...
Click to collapse
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
dark_darkness said:
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
Click to expand...
Click to collapse
I suggested custom recovery and not custom ROM. The idea is to get your phone back in working order first. Flashing a complete stock restore image should do it. Please refer to the thread I forwarded earlier. You should be able to flash custom recovery (like CWM or TWRP) to your phone via Odin and then use the custom recovery to flash the stock restore image.
This is what happened:
First I had Android 4.3 with KNOX
Then I flashed CyanogenMOD 11
I hated CyanogenMOD and tried to go back to stock firmware.
I downloaded the stock firmware from samfirmware.com and flashed with ODIN 3.09
Now i'm stuck on the Samsung Logo Boot Screen.
I have tried:
Reflashing
Using KIES emergency firmware recovery
Boot using safe mode.
Can you guys please help!?
Any error message in Odin? What is your current bootloader and which exact firmware are you trying to flash?
Androidwizzard said:
Any error message in Odin? What is your current bootloader and which exact firmware are you trying to flash?
Click to expand...
Click to collapse
CURRENT BINARY: Custom
SYSTEM STATUS: Official
KNOX WARRANTY VOID: 1
AP SWREV: A2
Trying to get stock Samsung firmware N7100UBUEMK4_N7100ZTOEMK3_ZTO
Odin does not shows error message...
RAFAMP said:
CURRENT BINARY: Custom
SYSTEM STATUS: Official
KNOX WARRANTY VOID: 1
AP SWREV: A2
Trying to get stock Samsung firmware N7100UBUEMK4_N7100ZTOEMK3_ZTO
Odin does not shows error message...
Click to expand...
Click to collapse
As your Knox counter says 1 I suppose you are trying to flash an older knox-enabled bootloader over a newer one.
Easiest way to succeed is to flash 4.4.2 firmware instead.
I have a Galaxy Tab Pro 8.4 rooted etc and recently decided to try a new ROM. I had TWRP custom recovery on it and worked fine originally. Unfortunately after flashing the new ROM, it froze and after rebooting it, I no longer have a recovery nor will it boot. It simply goes to download mode and says the following:
Could not do normal boot.
ODIN Mode
Product Name: SM-T320
CURRENT BINARY: CUSTOM
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRENTY VOID: 0x1
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
WRITE PROTECTION: ENABLE
UDC START
I've tried re-flashing custom recovery (TWRP) using ODIN and flashed successfully but all it will do is flash TEAMWIN for a split over and over. I wanted to try CWR but Odin only flashed md5 or tar files. PLEASE HELP!!!!
try another version of TWRP. I think there are two versions on their website, 2.7.1.0 and 2.7.0.0 or similar.
also make sure you are flashing the correct recovery for your device (wifi vs LTE model)
otgt said:
I have a Galaxy Tab Pro 8.4 rooted etc and recently decided to try a new ROM. I had TWRP custom recovery on it and worked fine originally. Unfortunately after flashing the new ROM, it froze and after rebooting it, I no longer have a recovery nor will it boot. It simply goes to download mode and says the following:
Could not do normal boot.
ODIN Mode
Product Name: SM-T320
CURRENT BINARY: CUSTOM
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRENTY VOID: 0x1
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
WRITE PROTECTION: ENABLE
UDC START
I've tried re-flashing custom recovery (TWRP) using ODIN and flashed successfully but all it will do is flash TEAMWIN for a split over and over. I wanted to try CWR but Odin only flashed md5 or tar files. PLEASE HELP!!!!
Click to expand...
Click to collapse
The cwm recovery in the original development can be flashed with Odin. Just unzip and flash (it is just a zip if a tar.md5 file).
crpalmer said:
The cwm recovery in the original development can be flashed with Odin. Just unzip and flash (it is just a zip if a tar.md5 file).
Click to expand...
Click to collapse
OK Great I was finally able to flash CWM (Attached) using ODIN. New Issue. I m unable to access the internal memory. If i go to browse internal SD memory, it shown nothing and reboots, and it does the same when I try to flash a ROM. What am i missing?
Any help would be greatly appreciated...
Did you try to flash the official rom ?
1) Get it here : http://www.sammobile.com/firmwares/
2) Type : SM-T320 in middle right search box (not top one)
3) findout your Country/Carrier from your unit
** you may need register to download .
Hope this help. Thanks !