Develop Bugs

[Q] Help! stuck at splash screen!

Hello, I recently acquired a note 2 n7100 and I have been trying to restore it. However, every time I try using odin, it gives me the that I the frimware upgrade encountered an issue error. I used the pit, but now it goes to the splash screen but nothing after that... Just a black screen. What should I do? I have been at this for hours and I am losing my mind!

Anyone have a solution? I am dying here!
EDIT: I got to the screen with the android on it and the little spinning ball in him, but then it just keeps booting to the android figure with the spinning globe. Any ideas?

You ll need to be more specific with your problem. Did you aquire the phone in working state? What were you trying to do. What did you do to achieve that? What was the results. What did you do to compansate that ? Etc....
Sent from my GT-N7100 using xda app-developers app

Try rebooting recovery (vol up+home+power)
wipe cache and data
if not works, input full details with complete odin log
and which ROM and pit file you have used

dr.ketan said:
Try rebooting recovery (vol up+home+power)
wipe cache and data
if not works, input full details with complete odin log
and which ROM and pit file you have used
Click to expand...
Click to collapse
Hello doc! I used the n7100 16gb pit you made and I am using the united arab stock rom, that is the only one that allows me to get to the android screen instead of a black screen. I tried the recovery button combo but that did not let me get into recovery.
I can update with my odin log when I get home. It all passes, nothing fails... So I guess I really dont know what is wrong with it.

Ok, try flashing stock recovery (get from here )
if you can flash it correctly then try rebooting in recovery and wipe cache and data.
otherwise post log of odin

dr.ketan said:
Ok, try flashing stock recovery (get from here )
if you can flash it correctly then try rebooting in recovery and wipe cache and data.
otherwise post log of odin
Click to expand...
Click to collapse
Thank you! Where do I find the log? Also if I can get this working I will definitely donate!

minnieman said:
Thank you! Where do I find the log? Also if I can get this working I will definitely donate!
Click to expand...
Click to collapse
The area which shows getting pit for mapping in odin application and all.
Sent from my GT-N7100

Ok, I tried flashing the recovery but that didn't work. I tried flashing the stock rom via odin again and it came up with the connect to kies error until I put the 16gn pit in and now it is back to the android figure with the spinning orb... Enclosed is the log, any other ideas? I am at a loss for words here.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXDMB5_N7100OJVDMB1_N7100XXDLK7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXDMB5_N7100OJVDMB1_N7100XXDLK7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!

UPDATE: nevermind, it officially bricked so I am sending it in to be resurrected. Thanks for the help anyways doc!

Well it is flashing normally. Find a rom that will factory reset your phone.
Sent from my GT-N7100

[Q] Galaxy note 2 (SPH-L900) Won't let me flash stock rom.

Last Night my Note2 finally got the 4.4 upgrade which I let install. Upon waking up I was greeted with my phone staying on the Samsung logo (it was doing the glowing animation both on the logo and the LCD so it wasn't frozen as far as I know). I've been trying all day to get it to work, I even tried flashing the Stock rom (KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5) via ODIN v3.07, unfortunately I keep getting the following when I try to flash the recovery:
<OSM> KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> recovery.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I've also tried Samsungs Kies Software and I haven't had any luck.
Can someone please help or at least point me in the right direction?
Any help is very appreciated.
Thank you so much

4.4.2 odin .tar file is available now:
http://forum.xda-developers.com/showthread.php?t=2780984

916
DaniLuv said:
Last Night my Note2 finally got the 4.4 upgrade which I let install. Upon waking up I was greeted with my phone staying on the Samsung logo (it was doing the glowing animation both on the logo and the LCD so it wasn't frozen as far as I know). I've been trying all day to get it to work, I even tried flashing the Stock rom (KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5) via ODIN v3.07, unfortunately I keep getting the following when I try to flash the recovery:
<OSM> KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> recovery.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I've also tried Samsungs Kies Software and I haven't had any luck.
Can someone please help or at least point me in the right direction?
Any help is very appreciated.
Thank you so much
Click to expand...
Click to collapse
Michael just helped me out in this thread I made, having the same issue as you. That fix.tar really helps! Just read his post in this thread: http://forum.xda-developers.com/showthread.php?t=2780409

Galaxy Note 8 GT-N5110- Stuck In Bootloop After Factory Reset

Boot loop after factory reset on GT-N5110
I tried to reset the device using Settings>Back up and reset>Factory data reset>Delete all.
Rebooted into a black screen with an Android with a hatch open and a blue spinning thing. It's been stuck in a endless loop of the startup screen with the name and model, which then goes to the Android with open hatch.
I pried the rear cover off and discovered that I don't have any screwdrivers small enough to remove the battery. So I'm wondering if there is any software based fix that I can try.
Holding down Power+Volume Down interrupts the loop and brings up this screen - blogyourearth.com/wp-content/uploads/2012/02/Samsung-Galaxy-S2-Warning-Custom-rom-installation.jpg
I've had the tablet for 2 years, so the warranty is long gone. I'd be open to flashing a Custom Rom/Kernel, as long as I'm able to go back to the default TouchWiz 4.1.2.

Bump/Update
Update/bump.
Tried flashing the stock 4.1.2. firmware from sammobile.com with Odin v3.07. - Doesn't seem to work, here are the status messages from Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N5110XXBMC9_N5110XACBMC9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img -----Status was frozen on boot.img for 3 hours.
<ID:0/004> __Xmit Write fail
<ID:0/004> XmitData Fail..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone have any idea what's wrong? Should I try a different version of Odin, different firmware or what?

emc_2 said:
Update/bump.
Tried flashing the stock 4.1.2. firmware from sammobile.com with Odin v3.07. - Doesn't seem to work, here are the status messages from Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N5110XXBMC9_N5110XACBMC9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img -----Status was frozen on boot.img for 3 hours.
<ID:0/004> __Xmit Write fail
<ID:0/004> XmitData Fail..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone have any idea what's wrong? Should I try a different version of Odin, different firmware or what?
Click to expand...
Click to collapse
Are you able to enter download mode without issues?

pvsgh said:
Are you able to enter download mode without issues?
Click to expand...
Click to collapse
Yes, no issues at all.

emc_2 said:
Yes, no issues at all.
Click to expand...
Click to collapse
Try flashing TWRP recovery, take a backup of your current ROM, and then try installing one of custom ROM .

pvsgh said:
Try flashing TWRP recovery, take a backup of your current ROM, and then try installing one of custom ROM .
Click to expand...
Click to collapse
Have no idea on how to do any of the above, but I'm googling now. Are there any guides/articles on how to do this, that You could point me in the direction of? Since I'm soft-bricked, is there any point in trying to back-up my presumably borked ROM? I've already downloaded my country specific, stock 4.1.2. ROM.
Many thanks for taking the time to help me and I apologize for the noob questions. I know my way around Windows, but when it comes to Android - I'm hopeless

I flashed TWRP successfully, I think...
Stumbled across the ODIN troubleshooting thread and one of the steps was to try different cables. The 10 foot cable I've been using for the past 8 months would only end up with a failure, stock cable... didn't even register. 8 inch cable I bought for my external battery had a successful flash in 10 seconds!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
i.imgur.com/HPziH0E.png

emc_2 said:
I flashed TWRP successfully, I think...
Stumbled across the ODIN troubleshooting thread and one of the steps was to try different cables. The 10 foot cable I've been using for the past 8 months would only end up with a failure, stock cable... didn't even register. 8 inch cable I bought for my external battery had a successful flash in 10 seconds!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
i.imgur.com/HPziH0E.png
Click to expand...
Click to collapse
OK so now you have a working TWRP recoveryand you also know what was causing ODIN to fail.
Next step would be to install a custom ROM, check the development section.
if you prefer stock then you ODIN your stock tar file which you downloaded.

Using TWRP, I backed up; EFS, Boot, Cache, System and Data. After the backup completed I followed the prompt to reboot and it booted into Android *happy dance*.
looks like all the user preferences are gone. No more password or background pictures and all apps have been removed from their folders. Basically looks like all the apps that I installed are there and any data associated. But all my preferences and set options are gone.
Going through the apps, I remembered that I had rooted using Framaroot. Do you think that may have been the cause for the soft-brick? Should I un-root and then try the factory reset again or just flash the stock ROM that I downloaded?
EDIT: didn't see your reply when I started typing this out. Since TWRP is flashed. Does that mean it has replaced whatever recovery Samsung had in place? If so; does having it installed/flashed increase the chance of a fairly stress free recovery in case of future problems?

So, it turns out pvsgh is pretty awesome!
It worked! Thank you so much. You rock!
Had to use another cable though. I think I need a new USB/Charge port
After flashing the stock ROM I had quite a bit of left over data like app folders and pictures/screenshots. Went into the stock recovery and did a factory reset from there, which wiped the internal storage back to factory state.
Should I flash TWRP again and use it to backup everything, now that everything seems to be working normal. Or just leave it as is?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N5110XXBMC9_N5110XACBMC9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Removed!!
i.imgur.com/j9neU0B.png

emc_2 said:
It worked! Thank you so much. You rock!
Had to use another cable though. I think I need a new USB/Charge port
After flashing the stock ROM I had quite a bit of left over data like app folders and pictures/screenshots. Went into the stock recovery and did a factory reset from there, which wiped the internal storage back to factory state.
Should I flash TWRP again and use it to backup everything, now that everything seems to be working normal. Or just leave it as is?
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
N5110XXBMC9_N5110XACBMC9_HOME.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Added!!
Odin v.3 engine (ID:4)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
boot.img
NAND Write Start!!
recovery.img
system.img
cache.img
hidden.img
RQT_CLOSE !!
RES OK !!
Removed!!
Remain Port .... 0
All threads completed. (succeed 1 / failed 0)
Added!!
Removed!!
i.imgur.com/j9neU0B.png
Click to expand...
Click to collapse
You can take a backup that you can use to restore your tablet if you ever get issues again.
Or just follow the same procedure again.
Taking backup is completely a user choice whether he want it or not.

[2015] ODIN failed flashes reflashing STOCK 4.4.2 - Please HELP :'(

Hi there!
I recently bought a N3N (N7505) :good: for mobile drawing. Since I bought it used, I found KNOX at 0x1 and the 4.4.2 it came with was already annoyingly buggy (lags everywhere, packed RAM & phone app FCs). I did manage to root it through CF-Autoroot (I think?) and even put a custom recovery (TWRP touch v2.8.7.0)
The problem is, everytime I download a ROM from Sammobile (md5 checks confirm undamaged downloads), it fails to flash via ODIN (flashes ALL THE WAY till the end and says FAILED - phone reboots perfectly to previous OS like nothing happened) and I'm wondering if I downloaded the wrong ODIN files, or is there something I'm missing?
So, i'm currently on N7505XXUCNL1 and wondering how I can reflash it (or a similar one) to refresh the phone anew :angel:
ROMz, Y U NO FLASH???
Any advice on what ROM would best suit me to refresh my N3N with???
:victory::victory::victory:Thanks in advance!!:victory::victory::victory:
UPDATE:
When i'm in Download mode, this is the information displayed
ODIN MODE
PRODUCT NAME: SM-N7505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
Secure Download : Enabled
KNOX WARRANTY VOID: 1
AP SWREV: (2)
The ODIN log for when I try to flash N7505XXUCNL1_N7505OXXCNL1_TPH is here:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The ODIN log for N7505XXUCOE1_N7505SWCCOF1_SWC is here:
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now I'm stuck on the Firmware update encountered an issue. Please select recovery mode in Kies and try again

can you provide us the log?

damadikaz said:
can you provide us the log?
Click to expand...
Click to collapse
The ODIN failed flash log??
Where do I find that?

damadikaz said:
can you provide us the log?
Click to expand...
Click to collapse
Greetings damadikaz,
I have posted my ODIN logs as an UPDATE on the main post for two separate flashes that both failed.
Any help is greatly appreciated:highfive::highfive::highfive:

Try flashing the latest stock ROM from here: http://www.sammobile.com/firmwares/database/SM-N7505/
Looks to me like the flash is failing because the bootloader currently on the phone is newer than the bootloader in the ROM you are flashing.

audit13 said:
Try flashing the latest stock ROM from here: http://www.sammobile.com/firmwares/database/SM-N7505/
Looks to me like the flash is failing because the bootloader currently on the phone is newer than the bootloader in the ROM you are flashing.
Click to expand...
Click to collapse
Oh WOW!!! It could be!
Thank you very much:laugh:
Going to download tonight and flash :good::good::good:
Will return with feedback!
Thanks again good sir! :highfive::highfive::highfive:

S4 mini keeps restarting

Hello guys,
My S4 mini (GT-I9195) is restarting after the Samsung GalaxyS4mini GT-I9195 screen.
I can enter Odin mode. I can update firmware. see below log from Odin.
After that, phone enters recovery mode and restarts and i'm back at the begining.
Any ideas?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> NON-HLOS.bin
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)

Hello razvanells. Sorry for taking advantage of your topic, but I'm having the same problem as you.
This also happened with the S4 Mini (but I9192 version) of a my friend. This device had no root and had a stock rom. He hung up and did not turn on anymore, locking on the screen Samsung Galaxy S4 Mini I9192. I downloaded the stock rom from the sammobile site and installed it by Odin. The log I received was identical to yours, saying that the installation occurred successfully, but when the device reboots it goes to recovery mode and it does not start, I can only enter the download or recovery mode.
I tried the hard reset and received the following error:
Formatting / data ...
E: format_volume: make_extf4fs failed on /dev/block/platform/msm_sdcc.1/by-name/userdata
Formating / cache ...
E: format_volume: make_extf4fs failed on /dev/block/platform/msm_sdcc.1/by-name/cache
Data wipe complete.
Click to expand...
Click to collapse
I tried to recover the stock rom using Kies but it did not work either.
After a lot of research on google, I found a guy saying he was able to recover a smartphone using TWRP and formatting the memory in FAT and then reformatting it to EXT4 (at that link: http://forums.androidcentral.com/t-...850-encrypted-phone-freezes-when-turning.html).
I tried to install TWRP by Odin, which according to the log occurred perfectly, but after restarting the device the Android default recovery was there (even entering the recovery mode as soon as the phone rebooted).
I tried to install the CWM for Odin, and so it was. Odin's log said it was successful but when the phone was rebooted there was the default Android recovery again (even entering the recovery mode as soon as the phone rebooted).
I have no more ideas, and I wanted to ask if anyone knows how to solve this?
Thank you.

razvanells said:
Hello guys,
My S4 mini (GT-I9195) is restarting after the Samsung GalaxyS4mini GT-I9195 screen.
I can enter Odin mode. I can update firmware. see below log from Odin.
After that, phone enters recovery mode and restarts and i'm back at the begining.
Any ideas?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> NON-HLOS.bin
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
même problème que vous