can't get unlocked - Verizon Galaxy Note 4 Q&A, Help & Troubleshooting

i have tried rooting many times now i have got to download mode to flash twrp with odin.
In download mode it does not say developer mode mine says system status custom and secure check fail recovery
but i cant get odin to flash twrp it fails

updates
i have never been able to get temp root with kingroot but i can with kingoroot
when i run the scrip it says fail at the very last line cid ends 1200
i flashed downloaded and flashed bpa1
anyone know what i am doing wrong

Update
It is a verizon note 4 i tried all several times i keep geting this same thing it says ccid was is 1200 and didn't change

joshpmerk said:
It is a verizon note 4 i tried all several times i keep geting this same thing it says ccid was is 1200 and didn't change
Click to expand...
Click to collapse
I believe your original CID MUST begin with "15", that's one five, if not I'm not certain it will work.
Have no idea why but someone smarter than me could probably tell you

I too am having problems with the temp root holding long enough to run those scripts. I read it helps to factory reset, then try it. I am close to doing that since I have backed up pretty much anything I need. Good luck! ?
Sent from my SM-N910V using Tapatalk

lareya said:
I too am having problems with the temp root holding long enough to run those scripts. I read it helps to factory reset, then try it. I am close to doing that since I have backed up pretty much anything I need. Good luck!
Sent from my SM-N910V using Tapatalk
Click to expand...
Click to collapse
Try sideloading the root method rather than downloading it on your phone.

I have reset it before starting even done the reset twice thing
My cid start with 15 thing but the samsung unlock n4 fix says failed and does not change my id

Is that my probelm that i am losing root before i get it done

I had a similar issue: Following one of the guides, KingRoot would crash around 51-52%. Whereas Kingoroot would work fine say it worked, but root checker said otherwise. Also the adb shell would hang when invoking su. Since the latest version of kingoroot seemed to work a bit, I decided to check the latest version of kingroot (4.95) instead of the outdated one in the guide, and it gave me temp root. You also need an SD card for the script to work. I didn't know this when starting out, and I only found out because it gave that feedback after spamming the adb shell with su and the rest of the script using autohotkey
try using the latest version of kingroot.
emmc brickbug check should also be able to tell you your cid
I didn't bother checking root checker, since I would see it on the adb shell from invoking su. This might save you a couple seconds if you need it. You could also check out AutoHotKey (I put my script for the script below).
Your sd card might mess up and display the wrong capacity after running the script. I had trouble getting twrp to recognize it after various formats (on the phone, in windows, and in twrp itself). After doing a full erase with format size adjustment in SDFormatter, I got it to show up in twrp again.
after that it's basically-> flash twrp in download mode with odin
-> install super su from twrp
-> debloater, titanium backup, or other means of disabling updates.
I did this from a 5.0.1 N910VVRU2BOG5 rom last night.
Edit: My auto hotkey script: uses ctrl to spam su 3 times, and shift to send the rest of the script
Code:
LCtrl::
Loop 3
{
send, su{enter}
sleep, 5
}
Return
LShift::
{
send, cd /data/local/tmp/{enter}
sleep, 5
send, chmod 777 samsung_unlock_n4-fix{enter}
sleep, 5
send, chown root.root samsung_unlock_n4-fix{enter}
sleep, 5
send, ./samsung_unlock_n4-fix{enter}
sleep, 5
send, yes{enter}
}Return

Related

Can gain temporary root, but Permanent root will not stick.

Hello xda, in accordance with the signup video I have scoured the earth looking for an answer. However I'm not sure how much necro posting is frowned upon here so I thought it would be safer to just start a new thread.
I have an HTC Desire HD from Telus(for use on the Rogers network). I am in the process of rooting it but have encountered a problem. I can gain temporary root on the terminal emulator(Because the $ turns to #) however when attempting to run clockwork flash clockworkmod recovery I get the error "An error occurred while attempting to run privileged commands!"
I get the same error when attempting the "Fix Permissions" so I'm currently at a loss of what to do.
I have the ninja superuser icon in the apps menu however when I open it the screen is blank. I am unsure if this is how it is supposed to be or not. I have seen several references to a permission box that pops up during some of the steps but I haven't seen that at all.
I've tried four separate methods, the last of which coming from this thread http://forum.xda-developers.com/showthread.php?t=954997
I am currently at step B.d which involves running the S-OFF tool and Easy Radio OFF tool. But still clockwork will not flash a backup, and when I restart the phone I can not get super user to work on the terminal (ie by typing su) and must use the rage method to regain temporary root.
Also, I don't know if this is related or not, but when I restart the phone and attempt to boot in recovery mode, the volume buttons don't allow me to select other options, and instead the phone just forces me to reboot normally.
Some more facts:
model HTC Desire HD A9191
Build # 1.32.405.6
Android 2.2
Anymore info I'm probably forgetting just ask away!
So my question is: Can anyone identify what the issue is?
Thanks much for taking the time to read my question.
Does visionary not work for you?
I've seen that alot of success has been gained by doing temp root and perm root through it?
It does sound like the rage method might not be working for you from what I can tell..
I do want to check all the steps you followed before where fine?
Sent from outer space on my DHD running beatmod gingersense v1.3
Visionary was how I rooted mine. Worth a try if you havent tried it: http://android.modaco.com/content/software/320350/19-nov-r14-visionary-one-click-root/
Thanks for the visionary suggestion, but Visionary still isn't working :/
Has visionary been tested with the Telus Desire? I heard there was a difference. What happens when I attempt to temproot is it moves to a blank screen then goes back to the menu.
When I used visionary on 1.32 it did not always work first try ... generally always worked after 2 runs. then used it to perm root
It works. You do not have Telus software in your phone anymore.
Sent from my Desire HD using Tapatalk
Try my method (I made it because the methods I found for my Telus desire HD were flaky at best and only got temproots from it.)
Since you already flashed to 1.32 start at step 2
If you want to go gingerbread, dl the 2.36.405 ruu and use that and your pc to put 2.3.3 on it (dont worry, it works fine, i was using it since it came out and built a rom based off that, kingdom, and pyramid roms for my own sense 3 rom) and use the gingerbreak method.
http://driphter.com/index.php?topic=3867.0
Still haven't managed to get root. JSLEnterprises my antivirus won't let me download your file :/
I'm at a loss for what to do.
lemonpartyz said:
Still haven't managed to get root. JSLEnterprises my antivirus won't let me download your file :/
I'm at a loss for what to do.
Click to expand...
Click to collapse
Disable your Antivirus (Avast say's its malicious), Norton or F-Prot says its clean.
and Internet Explorer 9 says its not trustworthy (because there's .bat files in the zip), Firefox says its fine.
There is no malicious code in the zip, you can edit each individual batch file in the Resource folder to see the code. Its very simple and basic.
I disabled my antivirus, but when I run Install Visionary nothing happens. The CMD window opens and says it has been succesfuly installed but nothing has been installed, and nothing appeared in the app menu.
Edit: I went into the resource folder and then followed the steps from there and everything worked, except I still don't have the # symbol in terminal (even when entering "su") and ROM manager still gives me the same error.
lemonpartyz said:
I disabled my antivirus, but when I run Install Visionary nothing happens. The CMD window opens and says it has been succesfuly installed but nothing has been installed, and nothing appeared in the app menu.
Click to expand...
Click to collapse
go into the resource folder, edit the visionary install batch in notepad, delete the "cls" line, save and exit
rerun it with the phone attached. See if it truly installed successfully.
lemonpartyz said:
I disabled my antivirus, but when I run Install Visionary nothing happens. The CMD window opens and says it has been succesfuly installed but nothing has been installed, and nothing appeared in the app menu.
Edit: I went into the resource folder and then followed the steps from there and everything worked, except I still don't have the # symbol in terminal (even when entering "su") and ROM manager still gives me the same error.
Click to expand...
Click to collapse
you dont need to use the termial in my method.
Once visionary is installed, and you run it, and everything is done exactly whats described in my 9 easy steps thread (along with outcomes along the way), then you should be perm rooted, with s-off and eng-off with supercid.
I managed to install visionary with your method, however when running Eng-S I encountered the error "Bootloader corrupt, DO NOT REBOOT! Seek help from XDA!"
Help?
Edit: Followed the advice here http://forum.xda-developers.com/showthread.php?p=14936635 and s-off worked properly this time. Hopefully my DHD won't brick on reboot. Could super user be the problem? it never asks me for permissions or anything, all I have is an icon and a blank screen when i open the app.
Edit2: Rom manager took three attempts to install correctly. Still the same result "An error occurred while attempting to run privileged commands!"
FML
lemonpartyz said:
I managed to install visionary with your method, however when running Eng-S I encountered the error "Bootloader corrupt, DO NOT REBOOT! Seek help from XDA!"
Help?
Edit: Followed the advice here http://forum.xda-developers.com/showthread.php?p=14936635 and s-off worked properly this time. Hopefully my DHD won't brick on reboot. Could super user be the problem? it never asks me for permissions or anything, all I have is an icon and a blank screen when i open the app.
Edit2: Rom manager took three attempts to install correctly. Still the same result "An error occurred while attempting to run privileged commands!"
FML
Click to expand...
Click to collapse
looks like the superuser application isnt running properly.
I would use the 1.32 ruu (not the pd98img.zip off the sd) and then from a fresh install (without resoring any data other than google account to visit the market)
run through the visionary, s-off tool, eng-off tool, and then reboot again, then install rom manager from the market, run it, it should ask you for permission and may hang for a second, and then say you have about 5 seconds to allow root permissions.
Then install rom's away. if you're not into making seperate rom specific app folders on your sd card, google JSL Er3BuS. its a sense 3 rom without the extra scripts.
How do I install the 1.32 RUU if I can't install it from the SD card?
Thanks!
lemonpartyz said:
How do I install the 1.32 RUU if I can't install it from the SD card?
Thanks!
Click to expand...
Click to collapse
It is very easy mate,
1. Download the RUU of your choice from http://shipped-roms.com/index.php?category=android&model=Ace
2. Put your phone in charge mode only with USB debug on.
3. Make sure you have HTC Sync installed on your PC, and close HTC Sync application from your system bar in windows (make sure that HTC Sync is not running as all you need is the driver)
4. Right click on the RUU file and select "Run as Administrator"
5. Connect your DHD by the USB cable to your PC.
6. Click some boxed and "next"s.
7. Waiting!
8. Profit!
I tried following the steps here http://forum.xda-developers.com/showthread.php?t=841890
But got the error "ERROR [120]: Low MAIN BATTERY POWER. When the battery is above 30%.
This is getting ridiculous lol
I'm sorry I'm such a bother.
naailalzuhir said:
It is very easy mate,
1. Download the RUU of your choice from http://shipped-roms.com/index.php?category=android&model=Ace
2. Put your phone in charge mode only with USB debug on.
3. Make sure you have HTC Sync installed on your PC, and close HTC Sync application from your system bar in windows (make sure that HTC Sync is not running as all you need is the driver)
4. Right click on the RUU file and select "Run as Administrator"
5. Connect your DHD by the USB cable to your PC.
6. Click some boxed and "next"s.
7. Waiting!
8. Profit!
Click to expand...
Click to collapse
Tried this, now the update process has taken 45 minutes.
Well, it took 5 hours to finish, but finish it finally did. Rom manager installed no problem, flashed no problem and I am in the process of installing cryogen. Thanks everyone for their help and kind words.
Fingers crossed cryogen works.
I'm going away for the weekend, but when I come back I'll update this thread with the full details of what went down so hopefully someone will be helped by my many many hours spent raging.
-Lemonpartyz
lemonpartyz said:
Well, it took 5 hours to finish, but finish it finally did. Rom manager installed no problem, flashed no problem and I am in the process of installing cryogen. Thanks everyone for their help.
Click to expand...
Click to collapse
Glad its sorted for you , and hoping it status that way...enjoy your custom roms setting your phone free
Look forward to your post letting us know how its going.
Sent from outer space on my DHD running beatmod gingersense v1.3

System Update 4.08.605.2

What is it and why am I getting this prompt? I'm rooted with 2.3.4
Obviously I shouldn't accept this update but does anyone know what this is?
Sent from my Xoom using xda premium
Hi. I am new.
I just installed the ROM 2.3.4 last night that was posted in the xda forum(upgraded manually from 2.2 on a Unrevoked rooted Dinc).
I installed the 4.06 ROM and I am reading the official was 4.08...
Do I need another upgrade? Or is this 'the' upgrade that is for root users?
Not trying to steal your post ugxvibe. both of our questions might have similar answers.
if you update will you lose root control? What about all the apps? I'm most concerned about not being able to tether...
Just flash wildstangs 4.08.605.2 ota rom. It is the newest ota update, but already rooted.
how do I do that? Through rom manager?
Is there a way to stop the update reminder from popping up without actually installing it? I'm afraid I might mess up my phone and don't want to risk losing everything g on it.
Guys, to stop the prompt from appearing just press install and it will try to reboot but will just error and u will never see it again trust me .
Sent from my HTC Droid Incredible using xda premium
d-pabs said:
how do I do that? Through rom manager?
Is there a way to stop the update reminder from popping up without actually installing it? I'm afraid I might mess up my phone and don't want to risk losing everything g on it.
Click to expand...
Click to collapse
Yes thru rom manager.
You can dissable the notifications by editing your /system/build.prop file. Look for:
ro.config.htc.nocheckin = 0
and change the 0 to a 1. If you dont see that line add it somewhere in the file.
I went to make the nocheckin = 1 modification, but I already had it, and I'm still getting the update notifications. Not even sure how it got there. All I've done is root with Unrevoked, maybe that does the edit?
NetGoo said:
I went to make the nocheckin = 1 modification, but I already had it, and I'm still getting the update notifications. Not even sure how it got there. All I've done is root with Unrevoked, maybe that does the edit?
Click to expand...
Click to collapse
It should have worked, you may need to clear the cache partition. Or there is another method go to /etc/security and rename otacerts.zip to otacerts.zip.bak
Like what was said above...
If you have Clockwork or some other custom recovery, if you just allow it to update when prompted, it will not install and will cause no other problems. You must have the stock recovery in order for the update to install.
It CANNOT install if you don't have the stock recovery.
But, I would also go into the /cache directory and find the update file and zap it (It will be obvious). I just use ADB and "rm" it from my PC. You could use root explorer or something. Otherwise you will have a big update file just sitting there and hogging space.
cmlusco said:
It should have worked, you may need to clear the cache partition. Or there is another method go to /etc/security and rename otacerts.zip to otacerts.zip.bak
Click to expand...
Click to collapse
I found the file thru root explorer but cannot change it due to message that says it's read only. other options?
Thanks.
bgtruitt said:
I found the file thru root explorer but cannot change it due to message that says it's read only. other options?
Thanks.
Click to expand...
Click to collapse
At the top of the screen in Root Explorer, change r/o to r/w. Then make your change.
Sent from my ADR6300 using xda premium
im rooted n using the clockworld mod for roms, I attempted to run the 4.08 update from User wildstang following the instructions but after installing the update n rebooting it just sits at "Dorid incredible" white screen and never boots. I may be doing something wrong here, can someone break it down for me? suggestions?
NOTE: I use CWMR 5X. Some wipe options below are not included in earlier recovery versions. Still wipe what is available the best you can.
1. Put the Rom on the root of your SD Card
2. Compare MD5 Sum
Windows: MD5 Calculator
LINUX: Open Terminal and type: md5sum [path to the rom on your sd card]
Mac: Open a terminal and type: md5 [path to the rom on your sd card]
3. Reboot to Recovery
4. Wipe these:
Main Screen:
wipe data/factory reset - x2
wipe cache partition - x2
Advanced:
Wipe Dalvik Cache - x3
Wipe Battery Stats - optional
Mounts and Storage:
Format-
/boot - x2
/system - x2
/datadata - x2
/data - x2
/cache - x2
5. Install Rom from SD Card by going back and selecting install from SD card.
6. Reboot and enjoy!
followed each step to the letter but still wont boot : /
Ok i changed nothing in the method of installing the rom and for whatever reason it worked!! 4.08 now phone is 10X faster and im loving it. Only issue i see now is i cannot get back into clockworld mod! why is that? i hold down power and vol down for a long time and when release it just starts the boot sequence any suggestions?
clutchdroid said:
Ok i changed nothing in the method of installing the rom and for whatever reason it worked!! 4.08 now phone is 10X faster and im loving it. Only issue i see now is i cannot get back into clockworld mod! why is that? i hold down power and vol down for a long time and when release it just starts the boot sequence any suggestions?
Click to expand...
Click to collapse
Uncheck fastboot in menu > applications.
Thank you sir.
clutchdroid said:
Ok i changed nothing in the method of installing the rom and for whatever reason it worked!! 4.08 now phone is 10X faster and im loving it. Only issue i see now is i cannot get back into clockworld mod! why is that? i hold down power and vol down for a long time and when release it just starts the boot sequence any suggestions?
Click to expand...
Click to collapse
I had the same problem, but after two times running the install its still getting the hang. Hopefully I'll get better luck on try #3.
Did you figure out what caused the temporary issue?
spitzaf said:
I had the same problem, but after two times running the install its still getting the hang. Hopefully I'll get better luck on try #3.
Did you figure out what caused the temporary issue?
Click to expand...
Click to collapse
I may have missed a format inside mounts and storage make sure you hit them all.
cmlusco said:
Yes thru rom manager.
You can dissable the notifications by editing your /system/build.prop file. Look for:
ro.config.htc.nocheckin = 0
and change the 0 to a 1. If you dont see that line add it somewhere in the file.
Click to expand...
Click to collapse
OK I've found the file you're talking about and it doesn't have that line in it so I need to add it. I can't easily get access to a computer right now to run the command line on my phone so i have been trying to use the terminal emulator instead. It says I doesn't have a text editor...is there a way to edit via the emulator? Do you wkno which commands to use?
Thanks again
Yep, still having a minor issue with this. I have added the line suggested and I have cleared my cache yet I still get periodic prompts to install the update. I'm not really keen on doing so. Can anyone else suggest a way to stop the (weekly) prompts?
Thanks

Wildfire S T-Mobile...can't seem to root...help?

Got the device today, and already came with the bootloader unlocked and S-On...but every method I've tried just doesn't work - even temporary root.
Here's the info on the phone:
-T-Mobile Wildfire S (Marvel PVT) running 2.3.5
-Firmware - 2.17.531.1
-HBOOT - 1.08.0099
Any driver files I've seen are either dead links or "not available in my country" (I'm in the USA), but I'm almost positive I have the appropriate drivers on my Win7 64-bit install, since anything I've had to do on my G2 was problem-free.
Here's what I've tried, all in both "charge only" and "HTC sync" mode, with HTC sync disabled/not running on the PC:
-SuperOneClick - freezes at step #7
-Gingerbreak - endlessly "works" and never accomplishes anything
-Flashing anything via the bootloader fails, either due to not being the "right" image (picks up and starts loading/installing, but then it seems like the file is corrupt and it's aborted - and I've tried multiple files/versions) or failing due to some Model ID mismatch or something
-Flashing a recovery through fastboot (from this thread: http://forum.xda-developers.com/showthread.php?t=1503393) seems to have bricked my recovery
-Anything else in that guide (basically anything zergRush) fails to copy anything over to /system or /sbin or whatever even though it says it successfully rooted at the end
-The temporary root procedure gives me some random error about drivers in the middle of the process and fails
I'm at my wits end here - I just don't know what I'm doing wrong, if anything. If I had known the Wildfire S would be such a PITA just to root, I probably wouldn't have gotten it and saved up for something else...at least I still have my G2 =/
Check that only one instance of ADB is running (in task manager).
try installing Busybox and Superuser from the market first then trying one of the other methods again
inconn said:
Check that only one instance of ADB is running (in task manager).
Click to expand...
Click to collapse
I went and killed it after each time in order to be able to delete the files, that wasn't it.
Nicknoxx said:
try installing Busybox and Superuser from the market first then trying one of the other methods again
Click to expand...
Click to collapse
Tried that too, didn't work.
Ended up doing a full reset because it refused to mount the SD card on my PC at some point, and tried this method:
http://forum.xda-developers.com/showpost.php?p=22178267&postcount=128
And managed to get it rooted that way. Much more inclined to keep my new WFS now
I have tmobile us and all I did was install cwm recovery and flashed a root.zip file. You can pm me if you need the file.
Sent from my HTC Wildfire S using xda premium
I know this thread's been dead for a couple months, but I didn't see that it was resolved...did you turn usb debugging on?
You need that on to root these phones...
Edit : NVM, I should have read a little bit more. Please disregard.

Stuck in bootloop after messing with framework-res.apk

I was in the process of replacing framework-res.apk and missed the step of changing the permissions before replacing it. I found several threads on how to unbrick the phone by flashing a new ROM but I was hoping I can somehow fix the permissions on the framework file and be done. I installed adb and I already had the LG USB drivers installed but when I run adb devices it doesn't list anything. Windows 7 shows "LG AndroidNet Phone" and a removable disk under "Safely Remove Hardware" so I think I have the right drivers.
Is there hope that I can fix the file permissions?
BTW, I'm a newb so I may be missing something. And also scared of having to flash a ROM
I need help.
do you have CWM in the phone ? if so boot into that and run adb devices and see if it finds it their
No, I don't. Other than using DooMLoRD zergrush to root the phone a few months ago, I have not messed with anything else.
gabcon73 said:
No, I don't. Other than using DooMLoRD zergrush to root the phone a few months ago, I have not messed with anything else.
Click to expand...
Click to collapse
unless your phone will boot normaly to the home screen or you have CWM on it you will haveto flash the koren rom theirs no way to get it into recovery that i know of ... have you tryed a factory reset ?
I replied to you at another thread, so I'll repeat here.
What you need to do is re-root while it's looping. It might take you 100 tries before it succeed , but eventually it should succeed.
After that you can try fix the permissions, but if the new .apk file is not copied successfully first time it might get you in boot loop again, so I'd recommend at that point push the .apk again and then change the permissions.
I found that zergrush dated 2011-10-21 has more chances to succeed, because it has more retries before it gives up, the new version tries only few times and gives up too quickly.
I've attached the root I was using with 3 versions of zergrush.
Open CMD window and execute root.bat, let it copy all needed files to the phone. If it fails, try execute loop.bat, it will just execute zergrush indefinitely , so you can go do other stuff. You can check if root succeeded by opening another CMD window and type: adb shell
then, if it shows sign "$" type su, if it shows "#" you are good to go.
P.S.
This method only works with AT$T stock rom, if you are on LU6200 you are probably out of luck, as their root requires wifi and user interaction...
Having CWM is very handy in such situations, not only because you can restore backups, but because you'll have root access.
Thanks [email protected], I'll give it a try. And yes, I have the stock ROM.
I'm having problems downloading root.zip, I've tried two computers and different browsers, it only downloads 554 bytes.
Yeah, for some reason it was downloading 404 page...
I reuploaded it.
I let the loop.bat run overnight without success so I decided to call AT&T and have it replaced under warranty. The new phone arrived today and I've been busy reinstalling and reconfiguring. I may install CWM just so I can easily recover from a backup in case I do some other stupid thing to the phone.
Thanks guys

[TUT]How To Obtain A Little Freedom

[Tut]How To Systemless Root+Root+More!
This was fully tested on SM-G928A;Baseband:UCU2AOJ1 on 5.1.1
Just in case needed //SM-G928A\\ **Full Odin Restore G928AATT2AOJ1**
$<Download Mode & Odin Systemless Root Flash>
Requirements:
1.A Windows Computer
2.Your Phone Device SM-G92-0/5/8A
3.Odin 3.10.7
4.Kernel_Root_Android_5.1.1_AT&T_SamFirm.NET
5.USB Drivers(Most of the time if connect the phone to the computer using the usb cord that comes with the device it will install all of the drivers if your computer is connected to the internet.
____________________
Okay now assuming that everything has been required, we can begin.
Turn off your phone and open Odin with admin rights on the computer & connect your phone to the computer using the usb cable that comes with the phone.
On the phone now hold all of these following buttons down, Volume Down+Home Key+Power Soon after once you see the blue screen release those buttons and press the Volume Up key to enter Downloading Mode.
Now in Odin on the computer, it should have recognized your device now press the "AP" button and open up for example, "G928A_Kernel_Root_5.1.1_SamFirm.NET.tar.MD5" now just press start and sit back and relax and soon you will have Systemless Root!(Note your phone will reboot which is normal after the flash.
--------------------
#<Obtaining Root Access>
Requirements:
1.A Windows Computer
2.Your Phone Device SM-G92-0/5/8A
3.USB Drivers(Most of the time if connect the phone to the computer using the usb cord that comes with the device it will install all of the drivers if your computer is connected to the internet.
4.Flashed The Systemless Root
5.Kingo Root
6.Root Checker Cost $FREE
7.SuperSU Cost $FREE
8.BusyBox Cost $FREE
9.Developer Options (USB Debug)
____________________
Okay now assuming that everything has been required, we can begin.
Go into Settings>System>About Device & Enable Developer Options.(Keep tapping the "Build Number" category until it says Developer options have been enabled.
Connect your device with your usb that which comes with the phone on the computer. Open "Kingo ROOT" on your computer with admin rights, and once the program asks you to turn USB Debug on, go on your phone into Settings>System>Developer options and make sure it is enabled as well as usb debugging. Wait for kingo root to find your device and once found, it will ask you to either "Reroot,Root, or Remove Root, click "Reroot" then wait for it to start.(After it starts you should see on your phone the kingo root usb app pop-up and show the same thing you see on your computer)
After it is done it should confirm you have been rooted and will ask to donate.
Now you may exit out of the program on the computer and the phone and once out of the app and back on your phone, you will want to look in your app drawer for the kingo root "Superuser" and uninstall this. Then head on over to the playstore if haven't all ready and install "SuperSU" & "Busybox" if want to. Once have the SuperSU app open it and install the su binary updates with the "Normal" option not the recovery one since we don't have that.... & once done just press OK DO NOT REBOOT or you will bootloop and will have to use Odin to reflash your system of your phone to get it back working out of the box "state"
UPDATE Have a pc around and can still boot with root:
Yamaha169 said:
You can restart the device while rooted... but you have to have ADB to do so...
When you reboot ... you will get stuck at the ATT logo... at this point... plug your phone in to your pc...
Open up ADB (COMMAND WINDOW)
type in
ADB devices
until your device # appears in adb... (this can take a minute for your pc to find your phone) so don't panic
This means the phone is found...
From this point... type
ADB ROOT
ADB SHELL
YOU will now be inside the shell of the device with root permissions
Now type
setenforce 0
(MAKE SURE LOWERCASE just like seen. "setenforce 0" if do Setenforce 0 it won't be found.....)
This will set selinux to permissive ... allowing the phone to boot...
Someone with enough experience could probably create a selinux permissive stock kernel ... but I've contacted several developers with no response ...
Click to expand...
Click to collapse
Now open up the root checker app & click verify to see if you truly do have root.(You must grant root access so allow once it pops up.) Enjoy your root but never ever reboot.
UPDATE: How to Root If Possibly not allowing you to root!!!
Step one you will need to of downloaded "Android Studio
Step two you will now need to install all of the updates(Well that's what I did) inside the studio program.
Step three now locate 'program tools" which for me was located here: C:\Users\NameofComputer\AppData\Local\Android\android-sdk\platform-tools
Step four make a cmd.exe file to go in the platform-tools simply just clicking on the "start button" on windows and searching "cmd" then dragging the cmd file to the folder.(Rename it to something like ADB Root or something different than just cmd)
Step FIVE download the su binary which can be located HERE and place it in the "platform-tools" folder.
Step SIX now almost there. Open the cmd file(ADB Root.exe) and once opened, plug the phone into the computer with the cable that came with your phone.
Step Seven:^.^ now with the phone plugged in and the program start, type this command to make sure your device is found:
Code:
adb devices
and if found you will see your attached devices and if more than one or can't see your device, you can do
Code:
adb kill-server
command and it will restart adb.
Step Eight: MAGIC time lol now that your phone is connected and you can see it is indeed listed, type these commands as followed:
Code:
adb root
adb remount
adb push su /system/bin/su
adb shell
chown 0:0 /system/bin/su
chmod 6755 /system/bin/su
You don't really have to do the other commands after pushing su it's just for pre-caution.
Step Nine: Now do the following at the top and try to use the Kingo root once more and click root or reroot.
If this doesn't work try to press unroot and restart phone then try this again.
Also like down below I talk about if you did reboot before you unrooted, you can still unroot but sometimes it's tricky and it needs you to do the adb remount before will work so just remember that...
--------------------
$#$<UnRooting & Keeping Systemless Root So You Can Reboot & Reroot>
Requirements:
1.Your Phone Device SM-G92-0/5/8A
2.Root Access(Superuser rights)
3.SuperSU Cost $FREE
4.Root Checker Cost $FREE
____________________
This is very simple and easy to do, all you must do after every root and before every reboot is to go into "SuperSU" and go into the settings and scroll down until you see "Fully Unroot" and click that and once done verify with the root checker that you are indeed unrooted but still have adb shell and once done that you may freely reboot with no bootloop and then if want root once more just use "Kingo Root" on the computer to reroot once more.(I'm hoping someone will come out with an app that does the same thing and works so we don't need the computer anymore which would make it much easier..)
Edit/Update:
I found that if you maybe forgot to unroot before a reboot that you can still unroot without the need of going into odin and reflashing stock system just by connecting your phone to the computer via the usb that which comes with your phone and opening up Kingo Root and waiting for it to find your phone then click unroot and wait for it after you have unrooted and you will hear a sound which means it's fixed! So just force shutdown the device with pressing both: Volume Down+Home Button+Power then it will boot back up as normal!
-------------------- ____________________ -------------------- ____________________
~My Findings Through Long Research & Errors~:
<How to Fix Wifi Bug That Comes With Flashing Systemless Root>
Requirements:
1.Your Phone Device SM-G92-0/5/8A
2.Root Access(Superuser rights)
3.SuperSU Cost $FREE
4.BuildProp Editor Cost $FREE
____________________
On your phone open up the "BuildProp Editor".
click on the search button and search for "ro.securestorage.support=true" now once found change the =true to =false and save. Now you must reboot for it to take place but remember to UNROOT before you reboot.
Now doing this your wifi will stay connected and you no longer have to enter your password millions of times so it will be nicer to keep systemless root.
--------------------
<How to Enable AT&T Hotspot System FULLYApp>
Requirements:
1.Your Phone Device SM-G92-0/5/8A
2.Root Access(Superuser rights & .SuperSU Cost $FREE)
3.Root Explorer Cost $3.99
4.NEW Modded TetheringProvision .apk Cost $FREE(Also can be found in this thread in attachments.
5.ADB Root cmd knowledge or Download SQLite Editor Cost $2.99
6.BuildProp Editor Cost $FREE
____________________
Okay my fellow members that stayed on 5.1.1 with me, this tut did once work but then at&t blocked me and it stopped working but now rejoice becase there is a bypass once more!!!
NEW WAY:
I'm not sure which worked so I'm gonna just tell you everything that I did...
1.I first rooted obviously
2.I found a new TetheringProvision.apk which I have uploaded down in the attachment and at the top.
3.I used adb root for this but this can also be done with sqlite editior so I'll explain both ways, first way will be the easy way the adb root...>>>
Step 1: Ensure you have the correct OEM drivers installed for your handset on the computer
Step 2: Download and install the necessary ADB drivers (v1.4.2)
Step 3: Enable USB debugging on your Android handset:
Go to Settings > About Device, and tap the build number 7 times or until you see 'You're now a developer' message.
Return to Settings > Developer options and use the toggle button to turn on USB debugging. Then tap OK button to accept the warning and continue.
Step 4:Connect your device to PC with original USB cable.
Step 5: Launch a command window on your Windows PC.
Step 6: Access ADB shell and run the following command:
adb shell now just type " settings put global tether_dun_required 0 " and enter.
________----------Now the sqlite way
Step 1:Go into sqlite editor and allow root rights...
Step 2: Locate "Settings Storage" and click on "Settings.db then click on "global"
Step 3:Locate tether_dun_required 0 and if not there add by clicking on the +
then fill out name as " tether_dun_required " >>And value as " 0 " and then save file and unroot then reboot.
Now then after all of that I downloaded the build.prop which I know you don't have to but it makes it easier for me to do so and probably for you too...
Step 1:Get build.prop editor from the playstore and open it to grant root rights.
Step 2:Click on the pencil icon on the top right where the search icon is.
Step 3: Scroll all the way down to an open line.(If not one make one.)
and put this in the line....>>> " net.tethering.noprovisioning=true " and then click the save button at the top right and then save it and unroot then reboot.
Then replacing the Tetherprovision.apk . >>>
Step 1: Download the NEW modded TetherProvision.apk at top or at bottom.
Step 2: get a root explorer and go to System/App/TetheringProvision
Step 3: Rename the actual TetheringProvision.apk to TetheringProvision.apk.bak
Step 4: in the same location, go into "arm64" and rename the TetheringProvision.odex to TetheringProvision.odex.bak
Step 5: Now locate the modded TetheringProvision.apk you've just downloaded and place it in System/App/TetheringProvision/ now should be two TetheringProvision, the TetheringProvision.apk.bak and the modded one, TetheringProvision.apk.
Step 6: change the property promissions of the tetheringprovision.apk to give it root rights by changing the promissions to look just like the actual one which is " rw-r--r-- "
Step 7: save and unroot then reboot!
Now youre wifi tether and usb should work!!! enjoy!
--------------------
<How to disable OTA & Security Notification>
Requirements:
1.Your Phone Device SM-G92-0/5/8A
2.Root Access(Superuser rights & .SuperSU Cost $FREE)
3.Titanium Backup & Titanium Backup Pro License Cost $Free | $5.99
____________________
Open up titanium back with pro license and freeze these following apps:
1.SecurityLogAgent(This is that annoying notification that which comes with the systemless flash root that keeps annoying you to reboot and undo what you done.)
AT&T Software Update(This will make it so AT&T won't push any updates to your device anymore so no need to worry about installing an update ota and losing your root or something else like bootlooping.
And again, all of this sticks after you unroot and reboot!
___________________________________________
<How to Get Youtube RED (Sort of) FREE!>
Requirements:
1.Your Phone Device SM-G92-0/5/8A
2.OGYoutube Cost $Free
Basically all you do here is download the modded sort of youtube app(OGYoutube) and install it then done! You now can download videos/music on the app and have access to run audio in the background plus NO ADS!!! (if there are I haven't seen any yet...)
Best part of this too since can't be used fttb, no need for XPOSED apk!
_____________________________
<How To Install Viper4android>
Requirements:
1.Your Phone Device SM-G92-0/5/8A
2.Root Access(Superuser rights & .SuperSU Cost $FREE)
3.Fast Reboot
4.Soft Reboot
5.Viper4Android V2.3.4.0
6.Audio_Effect.Config
7.Titanium Backup & Titanium Backup Pro License Cost $Free | $5.99
8.IRS Impulse Response Sample files
9.Root Explorer Cost $3.99
~~~~~~~~~~~~~
To Read the tuts yourself than rather follow my tut, you may do so by following This Link & This Link
~~~~~~~~~~~~~~~~~~
Alright, I decided to do my own detail tut to make it much easier so follow me and you'll have viper4android in no time : )
So let's get begin, download if not already, the busybox,SuperSU,TitaniumBackup,Fast reboot,Soft Reboot, & Root explorer. Now having all that done open up Busybox and allow it root rights and you may wait for it to research for a smart intall, or just press install. Once you installed it in the default location System/xbin, click on the will be installed to location and choose System/bin and install it there too.(Not sure why but that's what the tut called for.)
Now let's download the folders for viper4android, go ahead and download Audio_Effect.Config.zip file,IRS Impulse Response Sample files, & the Viper4Android V2.3.4.0 folder.
Now open up the root explorer and unzip all that which is zipped up.(Which is all of the files;Audio_Effect.Config.zip file,IRS Impulse Response Sample files.zip, & the Viper4Android V2.3.4.0 folder.zip
)
Now once all are extracted, we will begin putting what is needed where.
Let's start off with the ViPER4Android_FX_A4.x (The actual name of the folder) you're gonna want to long press it and copy this folder. Once done, you're gonna want to paste this folder in System>Priv-app and make sure to change the permission of the .apk to 0644 rw-r--r-- & the FOLDER to 0755 rwxr-xr-x(The folder should have the same permissions as the other folders in that location.) which is inside the folder to give it root access which is 0644;rw-r--r-- and if not sure what root permission should look like, refer to this link Or Google what it looks like, then save/press ok.
Now go back to where you extracted your folders, and this time copy the "audio_effects.conf and go to System>etc and find and rename the actual audio_effects.conf to audio_effects.conf.bak and then paste the copied modded audio_effects.conf here & DONT FORGET change the permissions to give it root rights.
Now after all is done, open the app "Titanium Backup Pro" and look for and freeze these following applications: 1.Adapt Sound 4.0 & SoundAlive 3.0 now open the app "Soft Reboot (Root) and click yes you want to do a soft reboot. Then once back up(If want you can click the "Fast reboot app" to quickly refresh the system) and running you should see the viper app inside your app drawer. Open it and install the update/software when ask you to and once done it should ask for you to reboot just click on ok and then go out and back to the "Soft Reboot (Root) then do another soft reboot.
Now almost DONE!!! Once back up and running again, go to your root explorer again where you extracted the folders and grab the folder of "ViPER4Android and move it to your device storage ex; Storage/emulated/0 (It's where the download folder is and dcim folder is.. Then finally, go toSettings>Device>Sounds and notifications>Sound quality and effects and toggle on all of the listings[NOTE YOU MUST PUT EARPHONES IN FOR THESE TOGGLES TO SHOW]; UHQ Upscaler|SoundAlive+|Tube Amp Pro now you're done enjoy viper4android via editing the settings in the app.
Edit
You need to download SELinux Mode Changer and give root rights and just click on permissive mode and all done. Also might need to use compatible mode in the Viper4Android settings.
I found that this mod works with Pandora and Youtube app but not with google music or the default music app and not sure how to fix that....
__________________________________0
This is some more quick finds which you don't need a tut for just information I'd like to share so you all know.
I found out that you can use Titanium Backup Pro Cost $5.99 and freeze anything you want such as bloatware and that annoying notification that appears every time you reboot if have systemless root installed "SecurityLogAgent" and as long as you UNROOT before you reboot, it is safe and everything you froze stays frozen.
Now I haven't tried uninstalling any system apps so I wouldn't advise doing that unless you wanted to but I don't see the point except to free space up since you can just freeze anything and does the same thing except for freeing space....
I haven't been able to unlock the bootloader in my research and errors which probably never gonna happen anytime soon....
I also never found an app that could root the device yet without a computer....
And yeah that's it! I just was so happy to find out all of this and just had to share it with xda members which are on the same boat as me that has been wanting some "freedom" which now can have a piece of it. : )
If found these tuts to be helpful, feel free to hit thanks button and if want donate.
AngelRyu said:
Just gonna get right to it and be fast.
Odin Flash Kernel for systemless root.
obtain root
Download SuperSU
After rooted download some sort of buildprop editor and search for " ro.securestorage.support=true" Now change =true to =false. and save!
Now go into the superSU app and fully unroot then reboot and also keep adb shell root!
So you fix the wifi bug plus keep the adb shell so you can obtain root once more! Now we just need some app that can give root access with 1 click without needing a pc and this would work for me until we can actually reboot with root without it bootlooping anyways.... I still can't find a wifi tether app or a method that works for the at&t hotspot app though...
Click to expand...
Click to collapse
Question for clarification.
So current method for rooting g928a is this systemless root.
Question 1, will it brick my phone with this root if i reboot, because i read somewhere on here that the phone will just keep on rebooting.
You mention using superSU app to unroot to reboot. So basically I have to unroot with superSU whenever I want to reboot then reflash again to get root?
fuzmik said:
Question for clarification.
So current method for rooting g928a is this systemless root.
Question 1, will it brick my phone with this root if i reboot, because i read somewhere on here that the phone will just keep on rebooting.
You mention using superSU app to unroot to reboot. So basically I have to unroot with superSU whenever I want to reboot then reflash again to get root?
Click to expand...
Click to collapse
Yes you must unroot to remove the su binary so the system acts like nothing has happen. I use kingo root for windows and it works every time with root all you need to do is hit "root" or it may say "reroot" and works every time. I have been playing with this a lot trying to do things to get it to reboot with root but have failed so far.... I wish someone with more experience would approach this so we could have an app to use at least so we not have to use pc every time to reroot until we get the ability to keep root and reboot.
Kingo root can be found here : https://www.kingoapp.com/android-root.htm
and this works after flashing the kernel from odin. This was the only way I actually found to be able to get root was with this because manually pushing su just didn't work for me....
Thanks for being much clearer on the instructions and idoit proof. I was worried about the bootloop and I thought there was no exit strategy on this expensive phone until you mention reflash. With your extensive tinkering on this, did your knox security trip up?
If this is the only possible way, maybe the community could make some sort of app that if we have to shutdown or reboot the phone specifically for g928a, it will safely unroot it for us.
TASKER?!
Anyone know if this still works after taking the latest OTA a few days ago?
The problem is this isn't root. I restart my phone several times a day. There is no point especially if I can't get a custom OS. However, thanks for making the instructions clear. And for anyone who doesn't understand systemless root, it's temp root. When you reboot dmverity sees the false file structure and tries to rewrite and reverse the changes, effectively removing root. On the Note 5 AT&T for temp root you didn't have to unroot before reboot as it wouldn't boot loop, it would just remove root and let you continue on. So something in this version must be getting farther in breaking past dmverity if it's causing the OS to bootloop.
tonys.94 said:
The problem is this isn't root. I restart my phone several times a day. There is no point especially if I can't get a custom OS. However, thanks for making the instructions clear. And for anyone who doesn't understand systemless root, it's temp root. When you reboot dmverity sees the false file structure and tries to rewrite and reverse the changes, effectively removing root. On the Note 5 AT&T for temp root you didn't have to unroot before reboot as it wouldn't boot loop, it would just remove root and let you continue on. So something in this version must be getting farther in breaking past dmverity if it's causing the OS to bootloop.
Click to expand...
Click to collapse
I was wondering if maybe we could place SU somewhere else so we might could trick it to reboot with root but haven't done it yet and or maybe keep SU on the sdcard/storage and use the terminal on the phone to push su to xbin every reboot but just hoping maybe can get root working without making the stupid thing bootloop.... Like I said I been doing a lot of dumb stuff with my phone because I have been so disappointed in this phone with not having wifi tether at the most really but now that got that I'm much happier but I'm still on the research of keeping root and being able to reboot.
I won't be updating until something maybe for sure comes along with 6.0 I can wait because my galaxy s4 I had stayed on stock version forever because was able to do everything so was no need to update really.... Anyways yeah lol maybe someone greater or maybe my playing around will work. WE can only hope...
Oh yeah, to the other guy NO it did not trip knox doing any of the things I've done. which I wouldn't care if could unlock the bootloader lol...
Edit:
I've done all I can think of and didn't work to keep root on a reboot except it did keep root without bootloop with a soft reboot...
I found out to maybe later will add tut up top but for now I'd like to tell you or whoever, if you do bootloop due to not being able to access the su unroot in time, you can still connect your device with Kingo Root in that bootloop and can unroot to save you from having to reflash every time... Might have to reboot as soon as you hear the found from the unroot though.
Oh and on a factory reset everything sticks excepts what was frozen becomes unfrozen just fyi...
Yeah, that's all I can find so I'm done with it hope someone can help later on but I'm just happy with wifi tether so much : )
So what all can we do with this root
Thank you for your hard work. it's very much appreciated!!!
Will pay part of my bounty which is 50 dollars pay day!!
But, please reply. what all can we do with this root!?
O0Gjulian said:
So what all can we do with this root
Thank you for your hard work. it's very much appreciated!!!
Will pay part of my bounty which is 50 dollars pay day!!
But, please reply. what all can we do with this root!?
Click to expand...
Click to collapse
Hi, I didn't come up with anything but the fix for wifi bug and hotspot app.
I just made a very detail tut to help others, but thanks.
I would wait on the bounty to be paid to someone who can make it possible to keep root on and still be able to reboot.
So in theory with this method I can root, install a modified tetheringprovisions, unroot (as hotspot is the only feature I actually desire), and go about my business without worrying about bootlooping or knox being tripped? Feels too good to be true, but I want to believe.
Just a reminder that Android 6.0.1 is right around the corner. If you don't fully go back to stock before the upgrade it will not flash and could possibly wipe the data partition. Both the system and boot images need to be 100% stock.
antizombie said:
So in theory with this method I can root, install a modified tetheringprovisions, unroot (as hotspot is the only feature I actually desire), and go about my business without worrying about bootlooping or knox being tripped? Feels too good to be true, but I want to believe.
Click to expand...
Click to collapse
It's true, that's how my phone is rolling with frozen apps and the modded hotspot without root, but still the systemless root remains in the system but doesn't do anything with out a computer or applying the kingo root to true root it.
I haven't tested the adaway yet so idk if will work or not.... and I been wanting xpose to work to disable youtube ads but haven't tried that either. . I might root tonight and try out adway tho.
But yeah to your question you are 100% safe and will not change anything or trip anything; phone can reboot all it wants with no bootloops with the modded tether is what I'm trying to say lol .. .
Edit:
Yeah adaway works after unroot and reboot. . . But I decided not to use it because a lot of people us adfly and it wouldn't let me access the link so yeah.....
On another note I froze a lot of stuff and done a lot of things not sure which part caused it but it doesn't bother me because I don't use samsung pay but in the end I had to freeze samsung framework for samsung pay because it kept saying force closed but which again Idc about that app so no biggy to me : )
Was Samsung Pay crashing before you started freezing apps? I have yet to use Pay but I'd prefer to keep my options open if possible.
antizombie said:
Was Samsung Pay crashing before you started freezing apps? I have yet to use Pay but I'd prefer to keep my options open if possible.
Click to expand...
Click to collapse
Honestly, I'm not sure but it had to be either the freezing at&t update or securityagent because it seemed to happen after that... Or could be the hotspot mod but I didn't get any crashes until i froze those 2 apps so idk...
Package Disabler in play store freezes apps so what's the point?
Can you fully remove with TiBu and be safe unrooted?
---------- Post added at 03:55 PM ---------- Previous post was at 03:40 PM ----------
navalynt said:
Just a reminder that Android 6.0.1 is right around the corner. If you don't fully go back to stock before the upgrade it will not flash and could possibly wipe the data partition. Both the system and boot images need to be 100% stock.
Click to expand...
Click to collapse
Yeah and from what I've seen of the nightmares people have been having with their Note 5's on Marshmallow, I'm staying FAR away from it!
I can confirm this works. Sorta a pain to have to reroot but hey, It's progress. We may never have a custom ROM option or recovery, But this is the next big thing. If we can find a app that'll just reroot us. it's perfect. (somewhat) Just rooted a few minutes ago. Going to play around. More than likely I'll re flash stock and make a youtube video for anyone needing questions or wanting to see it be done.
And I lied.. So, My experience was weird. Lagging constantly and weird download issues with a fresh wipe.
I'm sadly gonna have to unroot and hope that a better method would come out.
):
O0Gjulian said:
I can confirm this works. Sorta a pain to have to reroot but hey, It's progress. We may never have a custom ROM option or recovery, But this is the next big thing. If we can find a app that'll just reroot us. it's perfect. (somewhat) Just rooted a few minutes ago. Going to play around. More than likely I'll re flash stock and make a youtube video for anyone needing questions or wanting to see it be done.
And I lied.. So, My experience was weird. Lagging constantly and weird download issues with a fresh wipe.
I'm sadly gonna have to unroot and hope that a better method would come out.
):
Click to expand...
Click to collapse
I'm not sure why you would experience "lag" because I have no lag what so ever. Maybe try going to settings>system>developer options and change both transition animation scale and window animation scale to 0.5x
I've reflashed stock many of times due to to trying to find everything there is to find and I've had no "lag" but also you could download the soft reboot and fast reboot from market. Fast reboot frees up memory via closing and restarting certain apps, and soft reboot kills zygote and does a "hot reboot" without going through whole start up process .
Please reply I'm gonna try and help you : )
Also @
joe3681 said:
Package Disabler in play store freezes apps so what's the point?
Can you fully remove with TiBu and be safe unrooted?
---------- Post added at 03:55 PM ---------- Previous post was at 03:40 PM ----------
Yeah and from what I've seen of the nightmares people have been having with their Note 5's on Marshmallow, I'm staying FAR away from it!
Click to expand...
Click to collapse
I can confirm freezing anything won't harm the system on a reboot after unrooting but not sure about removing the apps would be safe. I have however remove the youtube app and reinstalled it in play store and it didn't harm anything.
AngelRyu said:
I'm not sure why you would experience "lag" because I have no lag what so ever. Maybe try going to settings>system>developer options and change both transition animation scale and window animation scale to 0.5x
I've reflashed stock many of times due to to trying to find everything there is to find and I've had no "lag" but also you could download the soft reboot and fast reboot from market. Fast reboot frees up memory via closing and restarting certain apps, and soft reboot kills zygote and does a "hot reboot" without going through whole start up process .
Please reply I'm gonna try and help you : )
Thanks for helping me! I went ahead and flashed stock and followed your steps!
Working great now!
NOW, My next question... What difference would it make if I used package disabler pro VS TBU?
Wouldn't both of these apps freeze the processes? Or would it make a difference with root and SU access?
Click to expand...
Click to collapse
O0Gjulian said:
AngelRyu said:
I'm not sure why you would experience "lag" because I have no lag what so ever. Maybe try going to settings>system>developer options and change both transition animation scale and window animation scale to 0.5x
I've reflashed stock many of times due to to trying to find everything there is to find and I've had no "lag" but also you could download the soft reboot and fast reboot from market. Fast reboot frees up memory via closing and restarting certain apps, and soft reboot kills zygote and does a "hot reboot" without going through whole start up process .
Please reply I'm gonna try and help you : )
Thanks for helping me! I went ahead and flashed stock and followed your steps!
Working great now!
NOW, My next question... What difference would it make if I used package disabler pro VS TBU?
Wouldn't both of these apps freeze the processes? Or would it make a difference with root and SU access?
Click to expand...
Click to collapse
I'm not sure because I've never heard of that program, but I did buy it just now for about $1.89 and the activation keeps failing so I can't test it to see the difference but with titanium you can do everything not just freeze stuff but back up apps and their data and much more.
Titanium backup has been around for ages which is why I recommend it.
Click to expand...
Click to collapse
I use package Disabler. Works like TiBu without root. Only reason to root would be to fully remove apps but would it boot okay after?

Categories

Resources