Related
Hi,
My Universal fail to power on.
It do not enter boot loader with light + power + reset and show no signs of life. Batteries are both new and tested in other working units.
When connected to USB, PC reports "USB device not recognised"
I had ROMS flashed but failed at 99%. When reset the units did not power on or showed any signs of life.
It had been working fine up until the unsucssesful flash update.
I would like to be able to use it for work .
Please either post replies here or email me [email protected]
Your time and efforts will be greatly appreciated.
Regards,
quou
quou2006 said:
Hi,
My Universal fail to power on.
It do not enter boot loader with light + power + reset and show no signs of life. Batteries are both new and tested in other working units.
When connected to USB, PC reports "USB device not recognised"
I had ROMS flashed but failed at 99%. When reset the units did not power on or showed any signs of life.
It had been working fine up until the unsucssesful flash update.
I would like to be able to use it for work .
Please either post replies here or email me [email protected]
Your time and efforts will be greatly appreciated.
Regards,
quou
Click to expand...
Click to collapse
Please try to enter the bootloader mode in a bright room as it is very difficult to see in poorly lit environment. Till you enter the bootloader mode your device will not be recognised. Perhaps one of the three keys is getting released..the light button is the usual culprit. Once you are in the bootloader you can reflash.
Thank d_ranade for your answer.
I am sure the screen is 'all black' and I've tried to press the buttons several times.
I think the main problem now is how to enter the Bootloader.
I sometimes find it takes several goes to get into Bootloader mode. If not, have you tried a hard reset?
I've tried whatever i can do. Hard reset is useless too.
quou2006 said:
Hi,
My Universal fail to power on.
It do not enter boot loader with light + power + reset and show no signs of life. Batteries are both new and tested in other working units.
When connected to USB, PC reports "USB device not recognised"
I had ROMS flashed but failed at 99%. When reset the units did not power on or showed any signs of life.
It had been working fine up until the unsucssesful flash update.
I would like to be able to use it for work .
Please either post replies here or email me [email protected]
Your time and efforts will be greatly appreciated.
Regards,
quou
Click to expand...
Click to collapse
I have sent you a pm, it should help you.
-Jwrightmcps
Thank Jwrightmcps for your help, but i can not enter the Bootloader ,so can not use mtty to do more.
Unable to start/see bootloader
I seem to have the same problem with my upgraded universal which was working fine for about ten days. Then I installed TomTom on it and again it was all working that evening.
Then, when I turned it on the screen went blank (white), so I re-flashed it, but, part way through the screen went black, so I left it connected for further hour and nothing. I have since been unable to get it to do anything, it is not recognised by activesynch, it will not charge (either from the mains or the USB on either of the batteries) nor will it turn on or respond in any way.
I have unset ‘allow usb connections’. I have tried solidly for +/-10 minutes doing the backlight + on/off button and reset bit - repeatedly, with my wife helping to ensure all buttons were being pressed. All I got was a message from MicroSoft telling me that ‘One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it’. The only positive thing is that every time I do it and depress the reset, the red LED flashes (provided I leave the USB cable in) but at no point have either of us been able to see any writing on the screen.
Any guidance (apart from where to take it for recycling) would be welcome…
It happened to me several times too. Even in the old ROMS. But had learned many things out of it. I removed the battery. Wait for several seconds or maybe minute before placing it back. And after placing it back wait again for some time before doing the "power + light + reset" (bootloader). At some point when I am in the bootloader mode already and reflashing, connected to the PC already, the screen went blank again. So I'm sure that something went wrong again. I repeated the procedure again (removing battery, placing it back etc...) and the reflashing continued. It takes patience (maybe).
After having experienced this so many times, I'm beginning to assume that it is not because the battery is "bad" or there is a problem on the ROM being reflashed. It is on how it (the battery) is connected to the unit. The reason why it does not turn on, charge even if connected to the charger, does not hard reset, does not react to anything... I just don't know.
One thing more, the procedure I said above sometimes does not work at once. But at least I managed to "resurrect" my device several times.
This I am sure, it is not in the ROM that is being flashed or the update...
Hope this helps,
Lelen
lelen, Thanks for your assistance. I tried last night, but it still could not enter the bootloader mode...
I have the same problem =( and i don't know what to do, someone told me that i have to change motherbord to resolve this problem, i hope there are some other solutions.
Dead Uni
I too had this problem. With the device not responding at all and not able to enter bootloader stops mtty from working.
Only way i could get it to work was to take it to an O2 shop to send it away for repair (luckily the O2 XDA range has a 2 year warranty and because its completely dead they cant tell the OS has been modified).
Unfortunatly like the previous post i think it can only be fixed by replacing the mainboard.
Hi all, i found this thread http://forum.xda-developers.com/showthread.php?t=291097&page=6
so many people have the same problem , and nobody found a solution? i can't believe that on all this universals died motherboard, and there is no way to fix it with some special cable or some programm.
yes,i post the last reply of the thread you mentioned above, but nobody can resolve it.
I recommend you remove the battery and leave it over night. Put the battery back on, ensure it is properly mouted and try booting it.
It worked for some, no idea why though. I'm actually suspecting a bad battery mounting, which results in the motherboard unable to detect a battery is iserted, thus refusing to boot.
finally managed to get mine fixed, mine was out of warranty too and sent it off to carphone warehouse express service, took 3 weeks but was fixed with a standard chargeable repair charge of £40
I have a somewhat similar problem but not from upgrading. I accidentally dropped the device after a successful upgrade and the screen got damaged. Someone picked it up, opened it and noticed it was on even though the screen was damaged, and then closed it back. By the time I got it back it was dead and could not come on again. I have since replaced the damaged screen, but the device will not come on and cannot enter bootloader either. The device get warm if the battery is left on.
coolbeans252 said:
finally managed to get mine fixed, mine was out of warranty too and sent it off to carphone warehouse express service, took 3 weeks but was fixed with a standard chargeable repair charge of £40
Click to expand...
Click to collapse
i guess thats what i will have to end up doing
anyone goten repairs done in north america?
( i live in western canada)
got the same problem
sofene said:
I have a somewhat similar problem but not from upgrading. I accidentally dropped the device after a successful upgrade and the screen got damaged. Someone picked it up, opened it and noticed it was on even though the screen was damaged, and then closed it back. By the time I got it back it was dead and could not come on again. I have since replaced the damaged screen, but the device will not come on and cannot enter bootloader either. The device get warm if the battery is left on.
Click to expand...
Click to collapse
hi..please let me know if your device is fixed and how you managed to fix it. my email id is [email protected]
http://forum.xda-developers.com/show...6&postcount=52
Okay so here is the deal. I just picked this sweet Epic up and started rooting it and I can't get it connected to the pc to get into the files. I set the phone to debugging, and even tried it with it off as well, then I connected the usb (and yes I tried alt cords too) to the pc and selected mass storage (I tried charging too). The pc says it's installing the drivers and even says completed and ready to use but on my computer screen it only shows my hard drive . I downloaded the starter sdk and tried those drivers as well. Even though I could not get it to recognize I started Odin and while phone was on it showed 2 ports, but once I turned the phone off and set it to download mode I get zero, zip, nada for ports available. Now I did see somewhere to set the code back to PDA and top to Modem so I did that as well. Still no luck. I am running stock Froyo EC05 2.2.1 and 2.6.32.9 kernel. Can someone please help me out? I had a Moment before this and never this many issues. Is there a way to just put the card in a reader and install the files and then put it back in my phone and run recovery from there? I've never had to do that before so I was wondering if it's an option if I can't fix this. Last thing is the charging time is way long and the hold isn't lasting long either. I'm no expert or developer, but I'm flashed many ROMs on my moment so I guess you can say I know a little. Please no tech jargon/lingo though to prevent unnecessary communication issues. Suggestions on GB ROMs would be nice too. I tried RandomKing but the links were no good. I hate the stock garbage on there and would love it if someone could help me get them off so I can continue with my rooting agenda.
Try with USB debugging on, connect to the computer then go into control panel and device manager, find phone entry, probably samsung android, then hit update drivers from Windows Update. Takes a while to load all drivers, sometimes more than 30 minutes. Then reboot computer and phone and try it.
As for ROMs they are ALL good. Read the description of each to find out what's in it and if you like it, try it.
Sent from my SPH-D700 using XDA App
Thanks for the reply. I tried that (unknown device) but I just keep getting windows has decided your driver is the best message when I even disabled, re-enabled, removed and re-installed all drivers. It's really bugging me and I'm not one to give up but I spent over 6 hours on this last night and I'm stumped. BTW what 2.3 ROMs do you know of that are stable with the least issues? Just suggestions of course as everyone has their own style...
Stick to the EG22 ROMs since EH06 and EH17 caused many phones to random reboot. After a few days EH17 started disconnected my calls. I have been using a ROM not listed on XDA. It is Bonsai B14 EG22 based. You can google Bonsai Android or click my signature. There are a few good ones in the development section here too.
Sounds like it is definitely a driver issue. There are samsung drivers floating around here. If you don't find a working set I will hunt them down tonight for you.
Sent from my SPH-D700 using XDA App
You can try the drivers in the first post of this thread:
http://forum.xda-developers.com/showthread.php?t=1052813
Thanks...
Cool I will try that out when I get home since work computers are usb restricted
Thanks for all your help and I'll update you tomorrow.
By the way I was playing a HD game on it today while charging and I got a charging paused, battery too hot or cold... Is this a problem with the EG22 build?
Another thing to make sure of is if your dial ##8778# it will bring up a menu, make sure your device is on pda.. believe it or not this helps some people
* PDA should be selcted under the USB Section.. the other section should be on modem
Sent from my old but still kickin Epic 4g
Yeah that's what I was talking about that I tried.
Now I did see somewhere to set the code back to PDA and top to Modem so I did that as well.
Click to expand...
Click to collapse
rooted!!!
Got Odin working and downloading now... Had to sneek my laptop into work to get her done but... LOL... Now time to get rooting!!!
Thanx guys... Will let you know what ROM I went with later today...
Working on putting on 2.3.4 EG22 v. Alpha "Hawk" [Journaled] EG22 AIO Volume/Hotspot/Lockscreen/Overscroll/Lag Fix but the download is taking over 2 hrs!
Phone isd not working at all now...
I put it through Odin and was following the prompts on the odin page that said to put victory_8G_100528.pit in pit and the tar in, hit start it went through and said something about partition and then the phone shut off and never came back on. It won't even charge now... NO life at all.
Fixed...
Okay I took the battery and sd card out, and then plugged the usb in while holding 1 & power down. That put it into download mode. From there I just put the battery and card back in and installed clockwork. BTW the only cord that would work was the one that came with the phone. Took me 12 hr to figure that one out because all the forums said to not use it. UGH
Thanks for all the help.
Also watch out for launchers that hide you notification bar, this can bork USB/sdcard detection, I just made a tip thread.
smartbeatz said:
Okay I took the battery and sd card out, and then plugged the usb in while holding 1 & power down. That put it into download mode. From there I just put the battery and card back in and installed clockwork. BTW the only cord that would work was the one that came with the phone. Took me 12 hr to figure that one out because all the forums said to not use it. UGH
Thanks for all the help.
Click to expand...
Click to collapse
There is a manufacturers cord that is the same connector but doesn't work, not sure which one but I use my old Palm Pre cable and a lot of others use Blackberry cables.
Oh so nice
Okay the new ROM is running great and is oh so sexy, fast and powerful, although I do not like the home page dock layout. I see no issues yet and I'm switching back to the Epic today after I beef up my old moment (which I had swapped to for the day because I thought I soft bricked the Epic beyond recovery) I promised to my mom. I'd like to find a stable GB build for her too but it doesn't look like the programmers have figured that one out yet.
BTW the cord I have is the one that looks a little weird on the end you plug into the phone and seems to be real stiff. I got more phones to mess with so thanks all...
Anyone know of any good tutorial sites that teaches how to develop and write codes? Flashing is one thing but getting to know the nuts and bolts to help others out is where I want to be.
Hi!
First of all i got AOKP + Franco kernel for 2w without any problem and I didn't change any option since last week.
This morning i rebooted it, it switched off and it didn't start again.
I cannot switch one my nexus again since then. I have always a black screen, also if I try to enter in download mode or in the recovery.
I tried to connect to my computer and smt times my laptop see a omap4400 (i'm not sure about the name) but after few second it disappears.
Tomorrow I'm going to the service center... But I have a big doubt:
What the hell happened this morning?
Thanks
Remove the battery for 5 minutes and try again.
If that doesn't work,
Follow this guide:
1. Download the zip file from http://forum.gsmhosting.com/vbb/f634...eeeee-1465412/, created by Legija
2. Extract zip to whatever location you're comfortable with (I used Android directory)
3. Open up Device Manager (Hold down Windows Key, press R, the type in devmgmt.msc and press OK)
4. Go to actions menu, select Add Legacy Hardware
5. Choose install manually, then have disk. Browse to where you extracted the zip, select the 'inf' file in usb_drv_windows
6. Choose OMAP, you'll get a popup if on Win 7, continue anyway (driver not signed)
7. Once completed with driver, pull battery out of phone, then plug it into USB
8. Double click omap4460_tuna_hs_pro.bat to start the process
9. Once completed, unplug from USB, put battery back in, and power-up!
10. Extra step - depending on what's been done, it may 'brick' again - suggest to do a restore or a wipe reinstall afterwards to be certain (mine bricked again next reboot)
Click to expand...
Click to collapse
biscuitownz said:
Remove the battery for 5 minutes and try again.
If that doesn't work,
Follow this guide:
Click to expand...
Click to collapse
This, if OP can't reach fastboot.
Sent from my i9250
I'm having the exact same problem. I saw my phone at maybe 10% battery in the AM, said screw it and let it die, woke up this morning and plugged the phone in and nothing. No LED light, black screen, completely unresponsive. I've tried every trick in the book, and the only one that seemed to work marginally even was using a different battery, which got my phone to boot to the encryption screen, but then shut off again. It did that twice, and now both batteries are useless.
I used Legija's program to try and bring some life back to my gnex, even though it's not the international version, just in hopes of getting some of my data back (I have already started the replacement process with Verizon since the phone was insured), but I got no luck there either.
It's extremely disappointing and annoying to me that this phone survived all sorts of ROM installations (I was also using AOKP on 4.1 if someone wants to start making connections), reformatting, tweaking, almost every setting on that phone was modified by me.
Not only that but almost any software or hardware problem I did run into I could solve in maybe an hour, but I let my charge run out and the phone just up and bricks itself? Now, that's just bull****... I would be very curious as to an explanation as to WHY on earth this would happen. Very confusing.
Not to hijack the thread, but my interest here is not restoring the phone to working condition but just seeing if I can pull my data off of it. I wouldn't even be posting here had I been able to have an SD card with my gnex, which I figured was unnecessary at the time I bought it since I knew the space on their was enough for me already, and the added branding of "Nexus" brand which had me under the impression it was maybe stable enough by itself. Not a mistake I'll make again..
Is it at all possible to get the data off of my phone at this point? At least partially? I believe encryption makes it impossible but I'm rather stubborn. Any help would be greatly appreciated..
owlieowl said:
I'm having the exact same problem. I saw my phone at maybe 10% battery in the AM, said screw it and let it die, woke up this morning and plugged the phone in and nothing. No LED light, black screen, completely unresponsive. I've tried every trick in the book, and the only one that seemed to work marginally even was using a different battery, which got my phone to boot to the encryption screen, but then shut off again. It did that twice, and now both batteries are useless.
I used Legija's program to try and bring some life back to my gnex, even though it's not the international version, just in hopes of getting some of my data back (I have already started the replacement process with Verizon since the phone was insured), but I got no luck there either.
It's extremely disappointing and annoying to me that this phone survived all sorts of ROM installations (I was also using AOKP on 4.1 if someone wants to start making connections), reformatting, tweaking, almost every setting on that phone was modified by me.
Not only that but almost any software or hardware problem I did run into I could solve in maybe an hour, but I let my charge run out and the phone just up and bricks itself? Now, that's just bull****...
Not to hijack the thread, but my interest here is not restoring the phone to working condition but just seeing if I can pull my data off of it. I wouldn't even be posting here had I been able to have an SD card with my gnex, which I figured was unnecessary at the time I bought it since I knew the space on their was enough for me already, and the added branding of "Nexus" brand which had me under the impression it was maybe stable enough by itself. Not a mistake I'll make again..
Is it at all possible to get the data off of my phone at this point? At least partially? I believe encryption makes it impossible but I'm rather stubborn. Any help would be greatly appreciated..
Click to expand...
Click to collapse
So just to be clear... You've been able to get it to boot all the way up to the encryption screen, right? If so you should be able to get into fastboot (Holding down BOTH volume rockers and the power key.) From there you could relock/unlock the bootloader to do a full factory wipe which might solve your boot issue.
As far as the data loss from the wipe, you could then try this: http://forum.xda-developers.com/showthread.php?t=1994705
TomBall718 said:
So just to be clear... You've been able to get it to boot all the way up to the encryption screen, right? If so you should be able to get into fastboot (Holding down BOTH volume rockers and the power key.) From there you could relock/unlock the bootloader to do a full factory wipe which might solve your boot issue.
As far as the data loss from the wipe, you could then try this: http://forum.xda-developers.com/showthread.php?t=1994705
Click to expand...
Click to collapse
I was able to get it to the encryption screen with my old battery that had a little bit of charge left in it twice, but it shut itself down on me both times. So now both batteries are useless.. I took it to the Verizon store hoping they would maybe try one of their batteries, but they just called customer service and told me they're just going to replace it at this point.
I have a feeling the charging mechanism is somehow damaged, because when I did get it to the encryption screen I had it plugged into a wall outlet and it wasn't charging at all. So, I can't turn the phone on whatsoever anymore.. if I could turn it on I could solve this problem... but it simply refuses to boot. The closest I came to interfacing with it was the OMAP Flash script, which did work, but didn't fix the problem.
So maybe if I could get the phone working enough to use ADB with it I could get my data back, but not even that seems possible..
owlieowl said:
I was able to get it to the encryption screen with my old battery that had a little bit of charge left in it twice, but it shut itself down on me both times. So now both batteries are useless.. I took it to the Verizon store hoping they would maybe try one of their batteries, but they just called customer service and told me they're just going to replace it at this point.
I have a feeling the charging mechanism is somehow damaged, because when I did get it to the encryption screen I had it plugged into a wall outlet and it wasn't charging at all. So, I can't turn the phone on whatsoever anymore.. if I could turn it on I could solve this problem... but it simply refuses to boot. The closest I came to interfacing with it was the OMAP Flash script, which did work, but didn't fix the problem.
So maybe if I could get the phone working enough to use ADB with it I could get my data back, but not even that seems possible..
Click to expand...
Click to collapse
If the phone isn't charging then there's something wrong with the USB port. One way to test that would be to use a battery charger. Also, try a different cable. I've had issues with a few different cables that for whatever reason started to not fit properly in the phone.
If you're USB port has gone bad then you'll need to either A) Always use an external battery charger. B) Get a replacement. C) Fix it yourself (Good guide here: http://www.ifixit.com/Guide/Repairi...+LTE)+Micro+USB+Charge+Port+&+Main+Mic/9641/1 )
I have a Samsung Galaxy S2 Epic Touch for Virgin Mobile I'm selling to a friend of mine. It's been working great for me for about the last year on VM. It was rooted and running Liquid Smooth and then CM 10.1 (both using CWM). When I called VM to transfer the phone to my friends account we ran into a road block because CM doesn't respond to the keypad phone codes VM uses to update the phone, or have the VM hands free activation apps.
I figured I might as well flash back to stock ROM anyway. I downloaded the ROM from here.
Odin got about 75% of the way through the flash and then failed. The phone won't turn off but instead keeps up a persistent splash screen asking me to connect the phone to Kies to do a system recovery (Which I did try and Kies can't seem to complete the connection. It sees the phone but can't connect to it, even after ensuring all drivers are up to date. But then I've never had much success with Kies).
I can still get into Odin on my phone so I tried downloading the .exe ROM instead of the md5 this time, but by the time the ROM downloaded Odin tells me the battery is too low to flash anything (which I believe). Problem is I can turn the phone off to let it charge properly (it pops up with the Kies message whenever I plug the phone in).
I've left the phone plugged into the wall hoping that maybe it is in fact charging, but the indicator light only flashes for a second when I plug it in. I'm working a double shift today so I left the phone at home hoping it will charge so that I can try flashing again, but does anybody have any experience with this sort of problem, or know if the phone will in fact charge?
jonnierod said:
I have a Samsung Galaxy S2 Epic Touch for Virgin Mobile I'm selling to a friend of mine. It's been working great for me for about the last year on VM. It was rooted and running Liquid Smooth and then CM 10.1 (both using CWM). When I called VM to transfer the phone to my friends account we ran into a road block because CM doesn't respond to the keypad phone codes VM uses to update the phone, or have the VM hands free activation apps.
I figured I might as well flash back to stock ROM anyway. I downloaded the ROM from here.
Odin got about 75% of the way through the flash and then failed. The phone won't turn off but instead keeps up a persistent splash screen asking me to connect the phone to Kies to do a system recovery (Which I did try and Kies can't seem to complete the connection. It sees the phone but can't connect to it, even after ensuring all drivers are up to date. But then I've never had much success with Kies).
I can still get into Odin on my phone so I tried downloading the .exe ROM instead of the md5 this time, but by the time the ROM downloaded Odin tells me the battery is too low to flash anything (which I believe). Problem is I can turn the phone off to let it charge properly (it pops up with the Kies message whenever I plug the phone in).
I've left the phone plugged into the wall hoping that maybe it is in fact charging, but the indicator light only flashes for a second when I plug it in. I'm working a double shift today so I left the phone at home hoping it will charge so that I can try flashing again, but does anybody have any experience with this sort of problem, or know if the phone will in fact charge?
Click to expand...
Click to collapse
The easy options are to borrow a battery from a friend with a s2 phone, or get a charger off ebay, or buy a new battery from the store which will probably come with a partial charge.
Sounds like your usb port may have died. That happens sometimes.
I was thinking of borrowing a battery. I have a friend with the same phone, so that's possible.
If the USB charger failed, however, would the blue charging light still flicker on when first plugged in? Because that's what it does. It doesn't charge, but it does seem to acknowledge that it's been plugged in. Also, when plugged into the computer it will still flash the plug me into Kies screen, but now my computer doesn't seem to even recognize that anything is plugged in.
Sent from my HTC0P4E1 using Tapatalk
jonnierod said:
I was thinking of borrowing a battery. I have a friend with the same phone, so that's possible.
If the USB charger failed, however, would the blue charging light still flicker on when first plugged in? Because that's what it does. It doesn't charge, but it does seem to acknowledge that it's been plugged in. Also, when plugged into the computer it will still flash the plug me into Kies screen, but now my computer doesn't seem to even recognize that anything is plugged in.
Sent from my HTC0P4E1 using Tapatalk
Click to expand...
Click to collapse
It is possible. I had a phone that the data burnt out on, but would still charge. Just one pin needs to be bad to cause some issues, but not break everything.
Could just be the battery is totally empty too. Getting a known good battery with a charge is the first step to troubleshoot this.
I have encountered this problem a time or two before when testing some of my many attempted multiwindow mods, the device will in fact charge, but it is going to take forever. After a double shift I would imagine you'd have enough charge to flash properly, so try it again afterwards. Also have you attempted to return to recovery? If Odin only partially completed, your custom recovery may still be there and you might be able to use the power off option from recovery, while the device is plugged in, and possibly tricking it into not powering on to the error screen.
WARNING! Everything in blue is simply conjecture and has not been proven to work, it is simply a working theory. If it does not work don't say I didn't warn you.
Title pretty much says the basics.
Details however are as follows.
SM-T210R, Have had this unit for about a year, always been in a case, never dropped, not a scratch/dent/ding on it and I use it every day.
Past couple weeks I was getting update notification from Samsung, I'd always put it off till I got home then not bother when I actually got there.
Finally, a long weekend for me.. I let the update run its course, No problems (500+MB's) And I believe it was upgrade to Kitkat from Jellybean.
Can't remember the exact version details.
Soooo, I use my tablet throughout the day everything seems to work great NO problems at all.
Notice my battery is down to like 20-25% and plug it in (Original wall charger and cable)
Go to get it the next morning, open the case expecting it to flash and display my lock/swipe screen, Nothing.. Not TOTALLY Black, you can see theres still a glow.
The screen still responds to touches ( I can swipe to unlock it and hear the sound)
I tried to reset power. Nope nothing except I can hear the startup tune.
Tried hard reset, nope same thing.
Tried every button combo I could think of or contort my hands/feet into.. Nope no joy.
Hit the internet... read, read, read, read, watch videos, watch more videos..
Ah-ha take the back off, disco battery, wait, replug and voila.
Nope.. not the issue
Different milliamp chargers, nope.
WTF??
Normally I'd think I did something to it, but I did nothing that I hadn't done at least 200 times already.
I'm convinced Samsung F'd my tablet w/their update, not only that but my $1200.00 drone sits idle over my holiday because my vision app resides on my sgt3.
Ideas?
My best solution so far...
Well its been like 2 days since my sgt3 lost its mind.
Found a solution.
EVGA - Tegra Note 7. (No hyperlinks allowed for me....Yet)
nvidia.ca/object/evga-tegra-note-tablet
DAYUMMMMM.
This thing blows my SGT3 right off the map.
Still would like to find a REAL solution, there's alot of configurations on my SGT3.
But in the meantime I think this'll keep me almost content.
-D-
Just download odin and the firmware for you country and flash it if it gets stuck at the boot get in recvory and wipe and flash once more works a treat
sounds like a bad flash i never let over the air upgrades there trouble always use a pc
Ps take any memory cards out before flashing once booted and working replace memory card
jasonvoor1313 said:
Just download odin and the firmware for you country and flash it if it gets stuck at the boot get in recvory and wipe and flash once more works a treat
sounds like a bad flash i never let over the air upgrades there trouble always use a pc
Ps take any memory cards out before flashing once booted and working replace memory card
Click to expand...
Click to collapse
Thanks Jason, I've not messed w/flashing the firmware through pc on this thing yet.
I've done it w/psp's, motherboards, routers etc, but never w/one of my tabs.
Just to confirm... I dont need a display on my tablet to flash it w/Odin?
dimzin said:
Thanks Jason, I've not messed w/flashing the firmware through pc on this thing yet.
I've done it w/psp's, motherboards, routers etc, but never w/one of my tabs.
Just to confirm... I dont need a display on my tablet to flash it w/Odin?
Click to expand...
Click to collapse
No, you don't need the display on your Tab, you just need Kies and Odin on your PC.
Place your Tab in Downloadmode(VolDown+Home+Power,release All buttons when you see the warning, press VolUp) then choose your PDA firmware in Odin(Obtain firmware from SamMobile) an hit start. After this boot into recovery and wipe/factory reset your tab if it's not booting!
Good Luck
Greets Daniel
xDaniel91536 said:
No, you don't need the display on your Tab, you just need Kies and Odin on your PC.
Place your Tab in Downloadmode(VolDown+Home+Power,release All buttons when you see the warning, press VolUp) then choose your PDA firmware in Odin(Obtain firmware from SamMobile) an hit start. After this boot into recovery and wipe/factory reset your tab if it's not booting!
Good Luck
Greets Daniel
Click to expand...
Click to collapse
Hey Daniel, Thanks for the info.
I found Odin was pretty easy to flash with.
I've tried 4 different FW images for the GT3-7 and taken the unit (almost) completely apart w/the exception of removing the actual digitizer and the lcd.
Same results after each install though.
It boots, plays the boot sound, but no display.
I guess next step is removing the screen.. After that I don't know what to do except possibly getting myself a lcd replacement..
Just might drop it off to one of the local shops and get them to do it that way I won't wind up paying for something and f'ing it up.
No joy w/my sgt3..
Hey Daniel, Thanks for the info.
I found Odin was pretty easy to flash with.
I've tried 4 different FW images for the GT3-7 and taken the unit (almost) completely apart w/the exception of removing the actual digitizer and the lcd.
Same results after each install though.
Even went so far as to try Kies to do the last one.
It boots, plays the boot sound, but no display.
I guess next step is removing the screen.. After that I don't know what to do except possibly getting myself a lcd replacement..
Just might drop it off to one of the local shops and get them to do it that way I won't wind up paying for something and f'ing it up.
No joy w/my sgt3..