Hi,
I used a long time CyanogenMod 12 and 13 with my LG G3 (d855). Suddenly some problems occurred. I flashed a lot of images and TWRP versions.
Last days I tried to flash wit the LG Tool 2014 original kdz images from LG.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I tried:
D85521C_00_1204 (21C).kdz
D85530C_00_0211 (30C).kdz
D85530F_00_0329 (30F).kdz and
Europe D85530B_00_1217 (30B).kdz.
Normally KingRoot and AutoRec worked fine. A short time. After using my phone a few minutes or hours i got bootloops and I had to flash again a clean official ROM. Sometimes I couldn't enter TWRP via buttons.
I think my phone has a hardware failure.
In the past few minutes I tried to flash the 30F image above. Android started regular and asked my which language I want to use. I scrolled down, selected German and the phone rebooted. Now I've a bootloop again. After a few seconds after flashing a original ROM.
Can you help me? Is the phone hardware bricked?
Best regards
Tim
Now I will try http://forum.xda-developers.com/showpost.php?p=64624353&postcount=3
Katzenstreu said:
Hi,
I used a long time CyanogenMod 12 and 13 with my LG G3 (d855). Suddenly some problems occurred. I flashed a lot of images and TWRP versions.
Last days I tried to flash wit the LG Tool 2014 original kdz images from LG.
I tried:
D85521C_00_1204 (21C).kdz
D85530C_00_0211 (30C).kdz
D85530F_00_0329 (30F).kdz and
Europe D85530B_00_1217 (30B).kdz.
Normally KingRoot and AutoRec worked fine. A short time. After using my phone a few minutes or hours i got bootloops and I had to flash again a clean official ROM. Sometimes I couldn't enter TWRP via buttons.
I think my phone has a hardware failure.
In the past few minutes I tried to flash the 30F image above. Android started regular and asked my which language I want to use. I scrolled down, selected German and the phone rebooted. Now I've a bootloop again. After a few seconds after flashing a original ROM.
Can you help me? Is the phone hardware bricked?
Best regards
Tim
Edit 1:
Now I will try http://forum.xda-developers.com/showpost.php?p=64624353&postcount=3
Click to expand...
Click to collapse
Edit 2:
Same Problem
https://youtu.be/6MlxVDFYpW0
Related
I unlocked my bootloader and rooted my HTC One X. I have used the ClockworkMod recovery.
I had CyanogenMod 10.2 installed and it ran perfectly fine.
Later on, I downloaded the 'cm-11-20140308-SNAPSHOT-M4-endeavoru.zip' file to install the the CM 11.2
But it seems something terribly has gone wrong.
This error message was shown during installing CM 11.2
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and it got stuck on this screen after rebooting
Later on I tried flashing the 'boot.img' of CM 10.2 to get back to that ROM, but I encountered this error.
But when I tried installing the 'cm-10.2.1-endeavoru.zip', it was a success, but I am still stuck at the same position.
Please help me restoring the phone back, I dont care if I have to revert back to HTC's Original ROM, as long as the phone is back working.
I am novice at this thing, so please bear with me if I ask some stupid questions.
khepacheley said:
I unlocked my bootloader and rooted my HTC One X. I have used the ClockworkMod recovery.
I had CyanogenMod 10.2 installed and it ran perfectly fine.
Later on, I downloaded the 'cm-11-20140308-SNAPSHOT-M4-endeavoru.zip' file to install the the CM 11.2
But it seems something terribly has gone wrong.
Please help me restoring the phone back, I dont care if I have to revert back to HTC's Original ROM, as long as the phone is back working.
I am novice at this thing, so please bear with me if I ask some stupid questions.
Click to expand...
Click to collapse
First of all if you want to install CM11 you must to use latest CWM from CM11 thread or TWRP2.7 or Philz latest. And now mount sd card copy your sense rom to the card install it, flash the boot img. and you are good to go. After this read again thread for CM11 and how to install and try agin but be shure you read the thread
use the recovery that thommy put in the first page of the cm11 post (or the philz last recovery) it seems that the cmw that you have doesen't support kitkat
hi.
i have LG G3 d855 32 gb version. i was trying to upgrade it from kitkat but there wasnt any option in the settings, so i tried to do it by using flashtool method. now i downloaded the stock firmware by using my imei number which shows my device is for hongkong. so i downloaded the tot file as well as kdz file. when i tried to flash tot file i got an error after 6% and it said that "Partition Change Fa.. (failed maybe coz i cant read after that).. now the version installed on my device was "lgd855-v10m-ISR". i havent made any backup and phone is stuck in download mode. i'm completely lost now. any help would be appreciated.
Thanks in Advance
software info
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Belalsuleman said:
hi.
i have LG G3 d855 32 gb version. i was trying to upgrade it from kitkat but there wasnt any option in the settings, so i tried to do it by using flashtool method. now i downloaded the stock firmware by using my imei number which shows my device is for hongkong. so i downloaded the tot file as well as kdz file. when i tried to flash tot file i got an error after 6% and it said that "Partition Change Fa.. (failed maybe coz i cant read after that).. now the version installed on my device was "lgd855-v10m-ISR". i havent made any backup and phone is stuck in download mode. i'm completely lost now. any help would be appreciated.
Thanks in Advance
Click to expand...
Click to collapse
It doesn't matter what your phone's imei is, all you need is to download the correct kdz files for your phone model. Try looking for a kdz for D855 instead of the imei. All you need is to flash the correct file for your phone model. You will never go wrong.
Hi,
I am a complete newbie when it comes to this so please explain in simple terms.
So I will explain as briefly as possible:
- I have Windows 10 x64
- Bought LG G3 last week, it had Android 4.4.2 (and was already rooted)
- It had overheating issues and battery died fast so I tried to update Android via LG PC Suite -> Did NOT work
- I read that having root access blocked it, but that I could update manually
- I installed USB drivers
- I setup ADB and Fastboot
- I tried using LG Flash Tool 2014 and the Android 6.0 KDZ but it did NOT work (always said there was connection error)
- I tried using lgg3rootdotcom's method to reset the phone back to STOCK ROM without root and followed their instructions to the letter (set COM to 41 etc)
- I did everything, but then it keeps coming up with an error on LG Flash Tool (at 6%)
- It repeats "LAF : Bin_User_Mode" three (3) times whereas in the instructional video it only showed ""LAF : Bin_User_Mode" once (1)
- Then "[ERROR] : Partition Change factory Partition (Phone!=tot)"
(I want to share images but I can't because I am a new member with restrictions, I will post images later today)
- I downloaded the .tot and .dll from lgg3rootcom's website
- I tried D855 Europe, Hongkong, and Taiwan .tot but NONE worked
- Now my phone ONLY boots into Download mode :crying:
- I cannot get into Recovery mode or Normal boot...
- I REALLY just want to get it back to stock right now... Please HELP!
Any help will be much appreciated! Thanks in advance!
I used exact instructions from this thread: http://forum.xda-developers.com/showthread.php?t=2772199
But it ERROR appears at 6% with "[ERROR] : Partition Change factory Partition (Phone!=tot)"
Also, please ask any questions if you want to know more so you can help me..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi everyone,
This is regarding my ASUS ZenFone 2 ZE551ML (1.8 GHz CPU, 4 GB RAM, 16 GB ROM). A few days ago, after 1 year and 11 months of excellent service, suddenly I saw that some of the apps (Play Music, ASUS MiniMovie) were corrupted. But a simple uninstall and reinstall fixed them. Later that day, I was about to open settings when a message popped up "Unfortunately, settings has stopped". Rebooting the phone did not fix it and I was totally stuck as I was unable to clear the data also for the settings app which also requires "Settings" to function. I managed to do a factory reset after which, I could not even get to the home screen because that involves the Settings app as well.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I went on to proceed with factory reset from the recovery mode and to my shock, the recovery mode was also corrupted. Screen just froze with a USB logo. I tried to flash the recovery with xFSTK but got write error.
Then I took apart the device and cooled the flash memory (SK hynix manufactured) with some IPA.
The device booted up and was able to get to the home screen. Then I followed the ASUS standard downgrade procedure to downgrade the device from Marshmallow to Lollipop (which should force flashing of the recovery as well and everything). Phone was stable then. Then following ASUS standard upgrade procedure, I upgraded to Marshmallow and did a factory reset again. Set up everything and phone is rock stable now, performs good as new with no slow downs or anything.
My question is "What exactly happened?" It was never rooted and very well taken care of (even looks like new). Is the flash memory failing? Can the firmware get corrupted on its own?
Any answers would be appreciated. Thanks.
Hello I am also having the same issue? Can you please explain more about the way you have recovered. I love my Asus Zenfone2. I am trying to do Factory RESET which causes this issue. Do you mean, use IPA to clean the Memory side? Please help me. My email ID is [email protected]
Firstly, try to flash it with xFSTK using the tutorial here on XDA. If it fails, then you need to take the phone apart.
Hello, I will use the Google translator because I am Brazilian
Today I ended up trying to install a custom rom on my moto g8, but it ended up giving some errors and I ended up blocking my bootloader manually, but now it doesn't start the phone and I can't install any stock rom with the bootloader blocked, all end up showing an error.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This website has instructions to flash stock firmware on Sofia. Everything but the link to download firmware should apply to Rav. https://www.droidwin.com/install-stock-firmware-on-motorola-g8-power-via-fastboot-commands/
Not because my bootloader is not unlocked
andr3ycarvalho said:
Not because my bootloader is not unlocked
Click to expand...
Click to collapse
A week ago I bricked my Moto g fast by attempting to flash RetUS firmware without unlocking the bootloader first. Even though most of the fastboot commands failed a handful succeeded and that was enough to prevent my phone from booting to anything but bootloader mode.
I downloaded and flashed the official Boost firmware from lolinet and while the flash succeeded my phone was still bricked.
I installed the Lenovo Motorola Rescue and Smart Assistant tool from https://support.lenovo.com/us/en/downloads/ds101291 and used it to download official firmware for my phone but the rescue tool failed at 14%.
I tried a few other things that also didn't help before I ran the LMSA rescue tool again. This time it took several minutes to complete and my phone worked again. I am not sure why it failed at first but happy to have a working phone again.
hello, i'm also brazilian and i have a problem similar to yours, after leaving a custom rom the other day, and reinstalling the stock and blocking the bootloader, my phone called with the message that it was corrupted and it wouldn't start and now i can only access his bootloader and I can't flash anything, not even the stock rom, I don't know how to solve it, but I'm in a situation similar to yours
Hello, I have a problem with my Moto G8 (XT 2045-1). I tried to install a stock rom to fix a bug, however the phone no longer connects in bootloader mode, nor does it unlock the same and I can't even install any stock rom. Can someone help me?