so i successfully rooted it using the cfautoroot. I installed TWRP. was all good, tried to install a rom from this site that said it was debloated. It said it would take a while to reboot and not to mess with it so i left it on the charger and went to bed. woke up 9 hours later and it still was on the same samsung screen, it doesnt boot loop it just hangs. I downloaded the stock md5 tarball from SamMobile unzipped it and loaded it into odin (drivers are already installed and recognized by odin.) Went to flash it the same way i did CFAutoroot and it keeps failing.
s268.photobucket.com/user/woundeddemonboy/media/13148467_10209280811761443_440193755_o.png_zpsnmjekjpf.jpeg.html
Heres the log incase you cant read it in the screen shot:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Related
Model: SM-N910A
This is what I get from ODIN.
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_ATT_N910AUCU1ANIE_N910AATT1ANIE_CL2774708_QB2373670_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
No matter what I do. I have tried using two different MD5's but no joy.
Any suggestions?
Thank you
I'm literally having the same exact issue. I'm on ATT. If you figure out whats wrong i'd appreciate it.
Here's my error code (i think identical to yours):
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_ATT_N910AUCU1ANIE_N910AATT1ANIE_CL2774708_QB2373670_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If you took the latest update, YOU CAN NOT ROLL BACK. I believe it is OCD5.
thepoetlives89 said:
If you took the latest update, YOU CAN NOT ROLL BACK. I believe it is OCD5.
Click to expand...
Click to collapse
Ughhhhhh!!!!!!! That sucks man.
Did you get it to work?
Hey guys
I'm in the same boat as you. Been trying all morning to flash using several different odins and images. By chance did you guys figure out a solution?
NO luck
facing same problem. Latest update messed up my network. Any SIM CARD not working,..
I just got this AT&T version of the Note 8 from a buddy, and am having a hard time flashing to CM13 6.0.1 with Odin 3.10.7. I have it rooted, but every time I try to flash the I467M_BNF5_BNF5.tar.md5 file, it fails. This is what I am getting:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> tz.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I feel like I am forgetting to do something trivial, so any help would be much appreciated
That has a locked bootloader. There is no custom recovery for that model. So roms are a no go on the ATT version.
Ah damn. I don't even want the phone part of it. I was trying to speed it up a little bit and get some customization options. I guess I can't be too angry because I only paid $75 for it and he had some pictures of his ex leftover on there. Thanks man
Hi guys,
I have a N7100 with TWRP 3.0.2-0 and Resurection Remix installed. My phone got stuck on GN2 logo when I woke up one day last week, hopefully anyone could help. Here are the symptoms:
normal boot will stuck on GN2 logo, it will not reboot, just stuck there. (I presume it's not bootloop in this case?)
get into recovery, TWRP 3.0.2-0 splash screen shows for 2-4 seconds, phone reboot (screen went dark), GN2 logo shows and stay.
able to get into download mode.
Here's the interesting part:
tried to flash other recovery with ODIN 3.09 and 3.11.1, the same TWRP 3.0.2-0 splash screen shows when access into recovery mode, phone reboot and stuck on GN2 logo. Have tried flashed stock recovery, philz 6.15.4, CWM 6.0.4.3, all still showing TWRP 3.0.2-0 splash screen. There were no errors, ODIN give a green PASS.
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
tried to flash original ROM from sammobile, ODIN give a green PASS, still stuck on GN2 logo.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> tz.img
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> modem.bin
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I failed to find any thread with the same symptoms as mine, most of them still could get into recovery or flash recovery. Appreciate if anyone could point me to any solutions that could revive my N7100. Thanks!
After flashing the full rom, did you do a factory reset before booting the stock rom for the first time?
Is there other way to do that other than going into recovery mode? as I can't get into recovery.
So I followed this guide [GUIDE] Fix an unflashable or soft bricked N7100! , and got the recovery package/ROM file (N7100XXUFNI4_OLBFNI1_v4.4.2_Repair_Firmware.rar) from else where (the original d/l link is dead). The .RAR file contains these 5 files:
AP_N7100XXUFNI4_2177951_REV04_user_low_ship_.tar.md5
BL_N7100XXUFNI4_2177951_REV04_user_low_ship.tar.md5
CP_N7100DXUFNI1_REV08_CL1477145.tar.md5
CSC_OLB_N7100OLBFNI1_2177951_REV04_user_low_ship.tar.md5
T03G_EUR_OPEN.pit
Flashed with all the files with .PIT and RePartition checked, ODIN gave a green PASS, but the same result; recovery shows TWRP 3.0.2 splash screen, stuck on GN2 logo.
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1101)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> param.bin
<ID:0/007> tz.img
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> modem.bin
<ID:0/007> Transmission Complete..
<ID:0/007> Now Writing.. Please wait about 2 minutes
<ID:0/007> Receive Response from boot-loader
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Removed!!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I've used ODIN 3.09, 3.11.1, different USB cables, plugged into different USB ports. Anyone have any other solutions? Thanks.
Did you try flashing the full Stock File with PIT?
Sent from my Xiaomi Mi 5 using XDA Labs
harishdayanand said:
Did you try flashing the full Stock File with PIT?
Sent from my Xiaomi Mi 5 using XDA Labs
Click to expand...
Click to collapse
Dj bang bong kinkong
harish15 said:
Did you try flashing the full Stock File with PIT?
Sent from my Xiaomi Mi 5 using XDA Labs
Click to expand...
Click to collapse
Yes, did both with and without PIT.
As the title says I can't flash the stock ROM back onto my phone. I stupidly formatted my phone through TWRP last week but I finally managed to get it repartitioned. I've tried everything on Odin I could think of. Here's what the log says:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1205)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed
Try installing the same or newer build of the firmware.
Where do I find that?
Sammobile.com
please help! cant flash stock rom back onto phone either
my issue is the exact same issue as him except i am using odin 3.1210, i have downloaded the latest firmware update and i get the same thing he did
an0ym0us said:
As the title says I can't flash the stock ROM back onto my phone. I stupidly formatted my phone through TWRP last week but I finally managed to get it repartitioned. I've tried everything on Odin I could think of. Here's what the log says:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1205)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed
Click to expand...
Click to collapse
My error exactly, I've been trying many different things for the past 5 hours still no luck
is this solved?
Sprint note 4. I"m on Lineage os 16. I lost all my backup files concerning twrp and stock backups. I'd like to return this device back to a stock sprint firmware to sell it on. I"ve downloaded Odin3 v3.12.4_4 and a stock .tar " Odin flashable N910PVPS4DQB3_N910PSPT4DQB3_N910PVPS4DQB3 " and it fails promptly. I"m assuming this is because I can't go backwards or down in versions. Am I stuck or is there something I have not been able to find that will enable me to go back to a stock sprint rom. Any help/guidance would be much appreciated.
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1205)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1