As I mentioned in my earlier thread I recently bought a Motorola Defy. Like many other users that I read about before purchasing my first android smartphone I was not able to open Google Market app after a factory reset.
My hint is based on my own experience and I hope it serves someone else well with similar issue.
As I write this message I have no data plan on my contract and I intend to use wireless connection for emailing, internet browsing, and the Market app. Once I completed the initial setup I put my handset's network mode to 2G only. I was worried to be charged for accessing data on 3G.
I had no problem using the Market app initially over the wireless connection until I did a refactory reset to re-setup my handset properly second time round. It was then the Market app stopped working and not even a master reset resolves the problem and then I was considering to root the handset to remove certain folders as a solution to the problem.
Everytime I laucnhed the Market app it stuck at Terms and Services page. It then occurred to me to change the network mode to Automatic and switch off the wireless connection to see what would happen. Next time I laucnhed the Market app it took me straight to the market's home page. It took me two days to figure this out : (
Once I was in the market I switched the network mode back to 2G only and turned on the wireless again. Everything is working just fine now. For the porpose of this thread I powered off the handset and turned it on again to see if my last settings i.e. 2G only still launches the Market app successfully or not. I can confirm that the Market app works just fine over the wireless connection just fine with 2G only network mode.
BTW, the batter life of this handset is so impressive. I used it one and half day very extensively (over 20 times of restarting the handset alone) and I was very surprised lasted that long. On moderate use and proper battery management (no widgets, no 24 wireless connection), and putting it on air plane mode at nights I would get over 2.5 days before charging is required.
I can't wait for Android 2.2 release to make this handset even more productive for me : )
CSharpHeaven said:
As I write this message I have no data plan on my contract and I intend to use wireless connection for emailing, internet browsing, and the Market app. Once I completed the initial setup I put my handset's network mode to 2G only. I was worried to be charged for accessing data on 3G.
Click to expand...
Click to collapse
I think you may have a misconception of 2G versus 3G. They are different technologies. When your phone is in 2G mode, it uses one type of network for both voice and data. In 3G mode it uses another type which provides better voice quality and faster data speeds.
Either way your phone will still try to access data unless you turn off mobile data. If it's in 2G mode and you see the little "E" icon up in the notification area, it's still accessing mobile data - just at a slower rate.
cmstlist said:
I think you may have a misconception of 2G versus 3G. They are different technologies. When your phone is in 2G mode, it uses one type of network for both voice and data. In 3G mode it uses another type which provides better voice quality and faster data speeds.
Either way your phone will still try to access data unless you turn off mobile data. If it's in 2G mode and you see the little "E" icon up in the notification area, it's still accessing mobile data - just at a slower rate.
Click to expand...
Click to collapse
Thank you for your inputs. I'm very new in the world of smartphones but learning fast.
I searched around to find out how to disable Mobile data and chosen this method *#*#4636#*#* and changed my network type to GSM for best coverage and battery life now. I can confirm the Masrket app still works with wireless connection.
Changing to GSM only does not disable mobile data.
Sent from my Nexus One using XDA App
cmstlist said:
Changing to GSM only does not disable mobile data.
Sent from my Nexus One using XDA App
Click to expand...
Click to collapse
I disabled the Mobile Data option by pressing the Settings button then More>Disable Mobile Data. It was then I noticed the options for changing my network type beyond just 2G and 3G.
CSharpHeaven said:
I disabled the Mobile Data option by pressing the Settings button then More>Disable Mobile Data. It was then I noticed the options for changing my network type beyond just 2G and 3G.
Click to expand...
Click to collapse
Did that work then? You no longer connect with mobile date, I'm asking because I have now ordered my Defy but like you don't have a network plan so need a workaround.
CSharpHeaven said:
I disabled the Mobile Data option by pressing the Settings button then More>Disable Mobile Data. It was then I noticed the options for changing my network type beyond just 2G and 3G.
Click to expand...
Click to collapse
Right ok, thanks for clarifying
In Froyo there is a mobile data toggle in the regular menus, and on all Sense phones too. Is there one on Blur phones? I guess not.
Another way to block data is to go to your APN list and fudge the entry (e.g. change epc.tmobile.com to epc.tmobile.com.nodata).
jk1234 said:
Did that work then? You no longer connect with mobile date, I'm asking because I have now ordered my Defy but like you don't have a network plan so need a workaround.
Click to expand...
Click to collapse
The only way I can assure you I have successfully disabled Mobile Data by looking at the reception icon in notification bar that no longer displays G, H, E, and 3G at anytime.
I hope I'm posting this in the proper category.
Namely, I'll be leaving my home country very soon and travel abroad and I will most certainly need to occasionally do SSH connection to my server over 3G, which leads me to data roaming. Now, data roaming at my carrier is super expensive, so I was wondering if there is a way to completely disable data while in roaming, but still be able to connect to 3G and EDGE when I explicitly tell the phone to do so (eg. for SSHing somewhere or checking in on Foursquare, refreshing Twitter timeline, etc).
I saw that there's an option to uncheck Data Roaming in Wireless & Network settings, but I would say that will completely turn off all data connections and NOT allow me to manually and explicitly initiate data connections. Is that true? Is there a way to make it connect to 3G only when I explicitly tell it to while remaining disconnected otherwise?
Allow all phone data settings on. Download APNdroid or similar (APN on off widget) from the market. Open app and set any preferences, then add widget to home screen. Activate by tapping on off on (or something like that). Green on, red off.
All it does is rename the APN settings so it "fails" to connect.
Sent from my GT-I9100 using XDA Premium App
petarpetrovic said:
I hope I'm posting this in the proper category.
I saw that there's an option to uncheck Data Roaming in Wireless & Network settings, but I would say that will completely turn off all data connections and NOT allow me to manually and explicitly initiate data connections. Is that true? Is there a way to make it connect to 3G only when I explicitly tell it to while remaining disconnected otherwise?
Click to expand...
Click to collapse
Your quite correct in that it will stop data connections, but why not turn it back on when you want to connect?, the other possibly cheaper option would be to, as long as your phone is not networked locked, buy a local PAYG sim with data and use that in your phone when you want to use 3G
Buying local sim would be wise option....
Sent from my Desire HD
A local prepaid SIM is a good idea, far cheaper than using data roaming.
Additionally, to avoid background data usage, you might want to install Droidwall and allow only the SSH app to connect to the internet.
ghostofcain said:
Your quite correct in that it will stop data connections, but why not turn it back on when you want to connect?
Click to expand...
Click to collapse
Because I want only that one application to use the data connection when I want it to, without all other apps opening their own connections for sync and other stuff, since I have a lot of apps and accounts that sync in certain periods of time (this is an Android device, after all ).
frosty_ice said:
Additionally, to avoid background data usage, you might want to install Droidwall and allow only the SSH app to connect to the internet.
Click to expand...
Click to collapse
Exactly what I needed! Many thanks for the suggestion, I'll try it out!
Can someone please explain to me in details what's the effect of the "Enable power efficiency" setting in the phone please?. i.e. does it turn off wifi or background data? and if so how often then it turns itself on to update data etc..
I am still really confused
I think it moniters your batt ,when it drops under a certain % it auto shuts down those features which cause heavy drain ie wifi mobile network bluetooth and auto sync ,just gives you a little extra time if your not in a place were you can recharge.
sent from my rootin tootin Revolution 6.3.1 DHD
mutsc0 said:
Can someone please explain to me in details what's the effect of the "Enable power efficiency" setting in the phone please?. i.e. does it turn off wifi or background data? and if so how often then it turns itself on to update data etc..
I am still really confused
Click to expand...
Click to collapse
As it self says, it will stop the auto sync for the applications like facebook, mail, google, HTC sense etc. when you are on device 3G mobile network. It has nothing to do with your wi-fi settings. Rather than using Auto Sync on your Mobile 3G network you can alternatively use "sync now" option in Widgetsoid app or plan when do you want to sync your data.
kaydee7902 said:
As it self says, it will stop the auto sync for the applications like facebook, mail, google, HTC sense etc. when you are on device 3G mobile network. It has nothing to do with your wi-fi settings. Rather than using Auto Sync on your Mobile 3G network you can alternatively use "sync now" option in Widgetsoid app or plan when do you want to sync your data.
Click to expand...
Click to collapse
So what's the difference with me turning off "Background data" manually?? If this is the case, this function is pretty much redundant.
its only automatic function. You can set which will be disabled when battery run low. you can fint it in options.
From what I observe at least with Desire HD & the recent 2.3.5 update, this option also affects the way device uses WiFi.
I do not know what exactly are the gradations of shudown for wifi physical or higher levels protocols, but apparently with this option enabled wifi is not so much "instant on" as it is without this option -- if the device is kept off ~10 (approx.) minutes and then switched "on", wifi connection appears only after some time.
Also (I guess as a result of the above), I observe that the device with this option enabled (being switched "off", e.g. during the night), brings up cellular data connection every ~40 minutes or so, I guess to service some data needs (this correlates with com.google.process.gapps activity). Apparently that's because it sees that wifi is really "off", and thinks it's more economic to use cellular data. I would say that average current draw does not change much due to that -- normal "always on" wifi does not take much power anyway.
My data usage has been rising. the day my data renewed, it instantly went up to 10 mb of data used in an hour.
If you go to Settings > Data Usage, you can see which applications use data on your phone. As the notice says, what is shown on the phone is the data measured by your phone, and your mobile provider may account for data usage differently. Still, it may help you pin point which apps consume most of your data. You then may want to delete the apps in question if you don't use them a lot, find replacement apps, or limit data usage for these apps to WiFi only -- to access this capability, an additionnal app will be needed; try searching the Play Store for this kind of tool.
I had the same issue but found the my wifi setting was to turn off in sleep mode, you can adjust this in your settings, it helped to change it to never turn off. Also, in the hidden wifi menu, make sure your wifi is set to on, you can access this by going to your keypad in the phone and typing *#0011#. Staying in wifi as much as possible is great, also, use your data toggle.
Alexandre-P said:
If you go to Settings > Data Usage, you can see which applications use data on your phone. As the notice says, what is shown on the phone is the data measured by your phone, and your mobile provider may account for data usage differently. Still, it may help you pin point which apps consume most of your data. You then may want to delete the apps in question if you don't use them a lot, find replacement apps, or limit data usage for these apps to WiFi only -- to access this capability, an additionnal app will be needed; try searching the Play Store for this kind of tool.
Click to expand...
Click to collapse
While looking at the list of apps using the data, you can tap on the ones you don't want running data in background. A detail menu comes up, at the bottom there is a check box to disable background processes on mobile network.
sent from my S3 Sammy Bean.
Hey All,
I just picked up my T-Mobile LG G3 last night and rooted it.
I am trying to use the tethering app like I did on the Nexus 5 but my other devices are not picking it up when I have it enabled on the new phone.
The app say's its enabled and shows the Name and passcode to join it, but again, no other devices that I was using before (ipad for example) see it when I scan for WiFi networks.
Can anyone please help? I use this app when at work and need to get it figured out and up and running again if possible.
Thank you,
Whiteice
Is the Wifi Tether Router app you're using by Fabio Grasso?
That's the one I was using on my Nexus 5 without any issues. I also just moved over to the Tmo G3 and can't seem to get any of my devices to pick up the SSID either. The developer says that it does work on the G3 and I also followed the settings laid out by the developer in his devices configuration page but still a no go. I emailed him to see if he may have some suggestions but no word yet. Hopefully he replies with something I/we can try to get this running. It was a great app on all my previous phones. I have faith in this developer, he seems to update his apps fairly regularly.
hoy128 said:
Is the Wifi Tether Router app you're using by Fabio Grasso?
That's the one I was using on my Nexus 5 without any issues. I also just moved over to the Tmo G3 and can't seem to get any of my devices to pick up the SSID either. The developer says that it does work on the G3 and I also followed the settings laid out by the developer in his devices configuration page but still a no go. I emailed him to see if he may have some suggestions but no word yet. Hopefully he replies with something I/we can try to get this running. It was a great app on all my previous phones. I have faith in this developer, he seems to update his apps fairly regularly.
Click to expand...
Click to collapse
Yes that is the same app I'm using.
I contacted him and he replied back asking Me to send a log file from within the app. I Did that this morning and waiting For further feedback. If I hear anything I Will report back here.
WhiteiceDMSTech said:
Yes that is the same app I'm using.
I contacted him and he replied back asking Me to send a log file from within the app. I Did that this morning and waiting For further feedback. If I hear anything I Will report back here.
Click to expand...
Click to collapse
I had the SAME problem with the app with my G3 and I've been back and forth with him via email. I had to try a few methods he gave me but the last one finally did the trick!
Here's his email that had the steps to get it to work below:
strange, yes other users use this app on G3
please try this config
Interface wlan0
Method 2
Channel 1
Encryption wpa2-psk
"No Firmware Reload" <- UNCHECKED
Let me know
Thanks
Fabio
Click to expand...
Click to collapse
It works now, because the settings on his site and his emails weren't working, but the above finally did it for me.
But I noticed the the DNS process, /system/bin/dnsmasq, was using on average 40% of my CPU constantly with the app enabled. So I checked the "Use Internal DHCP" in the DHCP settings and the process ended and the CPU use returned to normal.
I had asked in a reply if this app uses IP Tables to mask the hotspot use as mobile use or still shows up as Hotspot with T-Mobile. I wasn't sure if enabling or disabling the Internal DHCP would negate it or not, but he hasn't responded back yet.
Does anyone know if this app does mask it as mobile and not hotspot?
I just came off of Sprint to T-Mobile two days ago and I always used the native hotspot function on my rooted Note 3 that masked it as mobile use.
Hope it works for you guys as well.
JustLok said:
I had the SAME problem with the app with my G3 and I've been back and forth with him via email. I had to try a few methods he gave me but the last one finally did the trick!
Here's his email that had the steps to get it to work below:
It works now, because the settings on his site and his emails weren't working, but the above finally did it for me.
But I noticed the the DNS process, /system/bin/dnsmasq, was using on average 40% of my CPU constantly with the app enabled. So I checked the "Use Internal DHCP" in the DHCP settings and the process ended and the CPU use returned to normal.
I had asked in a reply if this app uses IP Tables to mask the hotspot use as mobile use or still shows up as Hotspot with T-Mobile. I wasn't sure if enabling or disabling the Internal DHCP would negate it or not, but he hasn't responded back yet.
Does anyone know if this app does mask it as mobile and not hotspot?
I just came off of Sprint to T-Mobile two days ago and I always used the native hotspot function on my rooted Note 3 that masked it as mobile use.
Hope it works for you guys as well.
Click to expand...
Click to collapse
Just tried those settings and so far it appears to be working.
Thanks you Fabio,
Whiteice
Darn, I wish it was working for me. I found that on Fabio's page and used those settings but they're still not working for me. Also tried to use the internal DHCP option but still no dice. I just sent Fabio my log file, hopefully he finds something that can get me up and running.
Woo hoo...I overlooked the method. Just confirmed the strings above works. Thanks all/Fabio!
JustLok said:
I had the SAME problem with the app with my G3 and I've been back and forth with him via email. I had to try a few methods he gave me but the last one finally did the trick!
Here's his email that had the steps to get it to work below:
It works now, because the settings on his site and his emails weren't working, but the above finally did it for me.
But I noticed the the DNS process, /system/bin/dnsmasq, was using on average 40% of my CPU constantly with the app enabled. So I checked the "Use Internal DHCP" in the DHCP settings and the process ended and the CPU use returned to normal.
I had asked in a reply if this app uses IP Tables to mask the hotspot use as mobile use or still shows up as Hotspot with T-Mobile. I wasn't sure if enabling or disabling the Internal DHCP would negate it or not, but he hasn't responded back yet.
Does anyone know if this app does mask it as mobile and not hotspot?
I just came off of Sprint to T-Mobile two days ago and I always used the native hotspot function on my rooted Note 3 that masked it as mobile use.
Hope it works for you guys as well.
Click to expand...
Click to collapse
I can confirm the above settings including the internal DHCP work perfect on my end also!
As a side note, it also appears that the data usage shows up on my T-Mo account as regular "Internet Access", not Hot Spot usage. Maybe I was looking at it wrong, or maybe my account hasn't fully updated yet, but it looks promising.
Thanks to JustLok for the tips!
Good to know it works. I tried it a few days ago and I didn't get any data, so I uninstalled it. Now that you guys confirm it's working, I might buy it.
I've been trying to get the stock tether to work. Found where to change the APN so that it doesn't use the pcweb one that tracks as hotspot, but I'm running into other issues, some other checks that need to be circumvented. This app is probably using the fast APN since pcweb is only listed deeply in the frameworks-res.apk of the G3 and those should never be used unless this app tries to tether as DUN (which I doubt).
Question, does this app have Tasker integration?
Just to clarify...'No firmware reload' should be checked or unchecked? Cheers!
wideasleep1 said:
Just to clarify...'No firmware reload' should be checked or unchecked? Cheers!
Click to expand...
Click to collapse
It would be unchecked, as listed in my post above in regards to the settings and tweaks to get it to work with D851 G3.
Also, been using it for days now and it does mask the tether use as mobile data and NOT as Hotspot data, as orbitalcomp confirmed, even using the internal DHCP server (which I was wondering if it would with the IP Table masking).
As for Tasker integration, I'm not sure what you mean havanahjoe with Tasker, as in the normal App Tasker or an app titled tasker?
I also noticed that my data connection just dies every so often, both on my G3 and my wife's G3. It show a connection with LTE and the data arrow up lit, but no data is moving. Even confirmed with the Internet Speed Meter Lite app that no data was being sent or received. I have to enable Airplane mode and then back off and the data connections becomes live again. I've read several reports of this on XDA too on Tmo G3's. This is either with the tether app or not, Tmo's data connection just stops working and needs to disconnect and reconnect to the tower/antenna to work again.
Finally, when using the widget for this tether app, when first tapping it (after a reboot or so), it does not enable it. You have to wait a little and then tap it again for it to enable. Once you get it to enable and become active, turning it on or off via the widget works on the first tap. It's just the first initial widget use upon a reboot that it takes two taps, about 5 secs apart to actually start up.
JustLok said:
It would be unchecked, as listed in my post above in regards to the settings and tweaks to get it to work with D851 G3.
Also, been using it for days now and it does mask the tether use as mobile data and NOT as Hotspot data, as orbitalcomp confirmed, even using the internal DHCP server (which I was wondering if it would with the IP Table masking).
As for Tasker integration, I'm not sure what you mean havanahjoe with Tasker, as in the normal App Tasker or an app titled tasker?
I also noticed that my data connection just dies every so often, both on my G3 and my wife's G3. It show a connection with LTE and the data arrow up lit, but no data is moving. Even confirmed with the Internet Speed Meter Lite app that no data was being sent or received. I have to enable Airplane mode and then back off and the data connections becomes live again. I've read several reports of this on XDA too on Tmo G3's. This is either with the tether app or not, Tmo's data connection just stops working and needs to disconnect and reconnect to the tower/antenna to work again.
Finally, when using the widget for this tether app, when first tapping it (after a reboot or so), it does not enable it. You have to wait a little and then tap it again for it to enable. Once you get it to enable and become active, turning it on or off via the widget works on the first tap. It's just the first initial widget use upon a reboot that it takes two taps, about 5 secs apart to actually start up.
Click to expand...
Click to collapse
Thanks for the update and confirmation of mobile vs. Hotspot..which meets my own experience. FWIW, your settings quote from Fabio simply says "No Firmware Reload" and doesn't state checked or unchecked...which is why I asked. At least I can't see it on Tapatalk. [emoji4]
Sent from my amazing LGG3!
JustLok said:
It would be unchecked, as listed in my post above in regards to the settings and tweaks to get it to work with D851 G3.
Also, been using it for days now and it does mask the tether use as mobile data and NOT as Hotspot data, as orbitalcomp confirmed, even using the internal DHCP server (which I was wondering if it would with the IP Table masking).
As for Tasker integration, I'm not sure what you mean havanahjoe with Tasker, as in the normal App Tasker or an app titled tasker?
I also noticed that my data connection just dies every so often, both on my G3 and my wife's G3. It show a connection with LTE and the data arrow up lit, but no data is moving. Even confirmed with the Internet Speed Meter Lite app that no data was being sent or received. I have to enable Airplane mode and then back off and the data connections becomes live again. I've read several reports of this on XDA too on Tmo G3's. This is either with the tether app or not, Tmo's data connection just stops working and needs to disconnect and reconnect to the tower/antenna to work again.
Finally, when using the widget for this tether app, when first tapping it (after a reboot or so), it does not enable it. You have to wait a little and then tap it again for it to enable. Once you get it to enable and become active, turning it on or off via the widget works on the first tap. It's just the first initial widget use upon a reboot that it takes two taps, about 5 secs apart to actually start up.
Click to expand...
Click to collapse
The hiding of the traffic is all about the APN. WiFi Tether Router uses the phone APN (fast.t-mobile.com) and the built-in hotspot uses pcweb.tmobile.com. That's why it's so easy to bypass, as long as WiFi Tether Router can do its thing by doing some iptables, dnsmasq and other Linux magic.
I have seen my LTE connection stop working from time to time. Not while tethering, but I rarely tether for more than 30 minutes at a time. Whenever I lose data, I just do the same, airplane mode on/off and it's back.
Tasker is an automation app. It's great for getting things done automatically. I use tethering in the car so that my dash mounted Nexus 7 can get internet. With Tasker, my hotspot is automatically turned on when I get in the car, and automatically turned off when I turn the car off. There is a method for applications to talk to each other in Android, these messages are called intents. With intents you can tell an app to shut down, to load a specific playlist (Spotify for example), or to enable/disable something. When using the stock Tether app, the system lets you toggle it with intents that Tasker already knows about. WiFi Tether Router has no intents, so there is no way to externally tell it to turn the hotspot on or off. The workaround is to emulate touching the enable/disable button (on the app or the widget). It's kludgy, but it works. It would be much cleaner and reliable if the dev enabled this functionality.
I tried the setting you suggested on the other thread, and by using Internal DHCP and not having WiFi Tether Router use DNSMasq to provide DHCP and DNS services, my battery drain is much more acceptable. I only lost 3% on my drive to work. I usually would lose 10% or more! This setting might be needed for other carriers where you do need to hide your data, but we don't have to worry about this with T-Mo.
havanahjoe said:
....
Tasker is an automation app. It's great for getting things done automatically. I use tethering in the car so that my dash mounted Nexus 7 can get internet. With Tasker, my hotspot is automatically turned on when I get in the car, and automatically turned off when I turn the car off. There is a method for applications to talk to each other in Android, these messages are called intents. With intents you can tell an app to shut down, to load a specific playlist (Spotify for example), or to enable/disable something. When using the stock Tether app, the system lets you toggle it with intents that Tasker already knows about. WiFi Tether Router has no intents, so there is no way to externally tell it to turn the hotspot on or off. The workaround is to emulate touching the enable/disable button (on the app or the widget). It's kludgy, but it works. It would be much cleaner and reliable if the dev enabled this functionality.
I tried the setting you suggested on the other thread, and by using Internal DHCP and not having WiFi Tether Router use DNSMasq to provide DHCP and DNS services, my battery drain is much more acceptable. I only lost 3% on my drive to work. I usually would lose 10% or more! This setting might be needed for other carriers where you do need to hide your data, but we don't have to worry about this with T-Mo.
Click to expand...
Click to collapse
Thanks for that explanation on Tasker, when I mentioned it to my wife last night, she said she was already using it on her old HTC One M7, so much for me being ahead of the curve. Or on the curve even, I guess. :cyclops:
I have noticed when using the Wifi Tether App, sometimes my laptop won't or can't connect to the hotspot after a while using it. I use it for extended periods of time at work, hours on end even, and my laptop will just disconnect from my SSID and won't connect, despite it being live. The SSID is seen and the laptop tries to connect but then just says it cannot do so.
I need to reboot my laptop for it to connect to it again. I'm not sure if it's the IP lease on my laptop expired or wasn't renewed with the tether app. Unfortunately, I cannot perform an IP renew or release in CMD on my laptop, because it's disconnected and needs a connection to do it! So I can't narrow the error to that function or not.
When I use the native Hotspot with TMo, I didn't have this problem last week when I was using it for three days before getting the Tether app.
Just some experience with it so far, in case anyone else was seeing the same or so.
How the heck did you all get this app to work? I cant change my apn settings to ipv4 like he says too. Data cuts off when I do
after update to lollipop not working
I was trying different settings,
After factory reset T-mobile hotspot is working, but when I tried to run "WiFi Tether Router" even t-mobile hotspot is not working...
Are you guys using d851 with lollipop?
Could somebody post for me correct settings?
Thx
clfuadam said:
I was trying different settings,
After factory reset T-mobile hotspot is working, but when I tried to run "WiFi Tether Router" even t-mobile hotspot is not working...
Are you guys using d851 with lollipop?
Could somebody post for me correct settings?
Thx
Click to expand...
Click to collapse
This app is broken in g2/g3 lollipop. It will also break built in tmo hotspot app as well and you would have to factory reset to get it working again. I switch back to kitkat just to use this app and also see no benefit in lollipop.. yet..
Can someone please help?
I can't get any of my computers to show the network name for WiFi tether router. I've never had this issue until today. My wife's phones doesn't have a problem, but mine won't show at all
I just switched to unlimited data on my LG G3 and got this app...
It works great with the G3 settings shown on the first page of this thread and on the app website. The speeds are the same on the device as on a client device so that's good...very fast LTE.
I originally tried setting the APN to LP4 (from default LP6) as the application directions stated must be done for T-Mobile but found that the network slowed (4G instead of LTE) and became somewhat unreliable. I'm wondering if this is even necessary on the G3 based on what I'm reading here. I switched the APN back to default.
My plan includes 5GB of tethering with unlimited on board so the problem is that how can I tell which data I'm using? My account page only shows unlimited it doesn't show how much of that is used for tethering even when I used the native tether app. I suppose I just have to try and go over and see what happens?
I've got this working on Cloudy 2.5 but the data is being counted as Hotspot data. Other than the settings earlier in the thread is there anything else I need to change so that it doesn't get counted as Hot Spot data?
TIA!