Develop Bugs

[Q] Help needed! Red exclamation mark

I have Htc one m8 unlocked bootloader 3.19, was rooted but doesn't seem to be anymore. firmware is 4.16.401.10, supercid (was roger001). I'm not sure what I am doing wrong, I tried to flash a RUU after flashing the firmware first and i get an error 32-header error. Phone just reboots onto white HTC screen then gives me the red exclamation mark. Booting into recovery gives red exclamation mark. Not sure what else I can try, any suggestioins would be greatly appreciated. (note: tried to flash the RUU here I could be way off but I am stuck.)
Anyone have any assistance? I tried changed the mid so I could flash a RUU but still got the 32-header error. There has to be a simpler way to do this, I just want to get back to stock.

Are you s-on or s-off? Do adb getvar all and post the output (delete your IMEI and serial number, as these are personal data).
With the Rogers variant, you can't flash the Euro RUU unless you change the MID (s-off required).
Also, you need to relock the bootloader to run the RUU if you are s-on. But that doesn't matter as the RUU will fail MID check, anyway.
What exactly are you trying to accomplish by running the RUU?

redpoint73 said:
Are you s-on or s-off? Do adb getvar all and post the output (delete your IMEI and serial number, as these are personal data).
With the Rogers variant, you can't flash the Euro RUU unless you change the MID (s-off required).
Also, you need to relock the bootloader to run the RUU if you are s-on. But that doesn't matter as the RUU will fail MID check, anyway.
What exactly are you trying to accomplish by running the RUU?
Click to expand...
Click to collapse
Thanks, I am on S-off. I thought that if you are s-off you didn't need to change mid but clearly i am wrong. I am just trying to restore to stock, I screwed up the phone trying to flash a zip and my recovery didn't work. I'll post that info in one sec

(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.25.214500021.06G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 4.16.401.10
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei:
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B16000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 3aa067db
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0

redpoint73 said:
Are you s-on or s-off? Do adb getvar all and post the output (delete your IMEI and serial number, as these are personal data).
With the Rogers variant, you can't flash the Euro RUU unless you change the MID (s-off required).
Also, you need to relock the bootloader to run the RUU if you are s-on. But that doesn't matter as the RUU will fail MID check, anyway.
What exactly are you trying to accomplish by running the RUU?
Click to expand...
Click to collapse
Would flashing a recovery .img , for example >recovery_4.16.401.10.img< allow me to return to stock??

Kevinj17 said:
Thanks, I am on S-off. I thought that if you are s-off you didn't need to change mid but clearly i am wrong.
Click to expand...
Click to collapse
Yes, that is incorrect. CID and MID need to match what the RUU is looking for. SuperCID will pass the CID check. But the MID check will still fail if you try to run the Euro RUU (MID = 06PB10000) on a Rogers version M8 (MID = 06PB16000).
Also, are you actually using the phone on Rogers' network? If so, I do not think that returning to stock Euro WWE version by RUU is what you want. From this webpage, it looks like Rogers uses Bands 4,7, and 17 for LTE. The Euro RUU will install a full stock image, including radio firmware, and according to these specs, the Euro version (EMEA) is missing 2 of the 3 bands (Bands 4 and 17) needed for LTE to work on Rogers network.
Kevinj17 said:
I am just trying to restore to stock, I screwed up the phone trying to flash a zip and my recovery didn't work.
Click to expand...
Click to collapse
What zip did you try to flash exactly?
---------- Post added at 09:41 AM ---------- Previous post was at 09:23 AM ----------
Kevinj17 said:
Would flashing a recovery .img , for example >recovery_4.16.401.10.img< allow me to return to stock??
Click to expand...
Click to collapse
That would just be the actual stock recovery program that installs of OTA updates, etc.
Its not the actual stock OS or firmware, if that is what you are thinking.
The red exclamation indicates you are already on a stock recovery. Flashing this won't help you at all.

Yeah haha I figured that out right after posting. Thanks though. I re-flashed TWRP now and gonna try restoring from a nandrod backup i found then flash the matching firmware. see how that goes. The similiar names is what throws me off sometimes, so many different recoverys n sh*t lol

I was tryign to use a sixaxis controller to play games but kept getting and error about 'position executable variables' when loading the sixaxis app so i downloaded something called 'bypass pie' and flashed it. Clearly i should have backed up first. It was just inpatient, but it unrooted my phone and stuff so i tried to restore from a backuop like 2 weeks ago and it was corrupt so it messed things up

my htc one_M8 didnot recived lollipop update ! ! ! help pleas.

Hi there I am new to HTC this is my firs HTC phone. I have HTC one m8 device with android 4.4.4 kit Kat and I want to update it to android 5 lollipop . when I go to settings and checking for updates it says (your phone is up to date there are no updates available for your phone ) I also tried HTC sync manger but with no luck so far .
So why there is no updates for my phone ?? ( I am not rooted or unlocked the boot loader)
Any way to download the Rom and install it via pc ?? (Program like Odin To install roms to htc ).
I am sorry for the bad English language because it's not my nature language .

kirkuk said:
Hi there I am new to HTC this is my firs HTC phone. I have HTC one m8 device with android 4.4.4 kit Kat and I want to update it to android 5 lollipop . when I go to settings and checking for updates it says (your phone is up to date there are no updates available for your phone ) I also tried HTC sync manger but with no luck so far .
So why there is no updates for my phone ?? ( I am not rooted or unlocked the boot loader)
Any way to download the Rom and install it via pc ?? (Program like Odin To install roms to htc ).
I am sorry for the bad English language because it's not my nature language .
Click to expand...
Click to collapse
Post the results of fastboot getvar all Delete the serial# and IMEI from the output. That is private information.
There may be an RUU that you could run to update, and your getvar will give the information that is needed to determine that.

xunholyx said:
Post the results of fastboot getvar all Delete the serial# and IMEI from the output. That is private information.
There may be an RUU that you could run to update, and your getvar will give the information that is needed to determine that.
Click to expand...
Click to collapse
thank you bro for replay i appreciate that ....
this the result of ( fastboot getvar all ) .
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.25.21331147A1.06G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.36.401.4
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B67000
(bootloader) cidnum: HTC__J15
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 56f9ae32
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.040s

kirkuk said:
thank you bro for replay i appreciate that ....
this the result of ( fastboot getvar all ) .
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.25.21331147A1.06G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.36.401.4
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B67000
(bootloader) cidnum: HTC__J15
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 56f9ae32
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.040s
Click to expand...
Click to collapse
I'm not sure that Lollipop is even available for the Middle East/Egyptian model. Your best bet would be to spend $25 for Sunshine S-Off, convert to superCID, and update with WWE/International firmware. You could also try to change your MID to 0P6B10000 and update that way, but there is a very real risk of bricking if you do that.
---------- Post added at 07:48 PM ---------- Previous post was at 07:22 PM ----------
You could also try this. No guarantees that it will work, but it might (your CID is listed as compatible, but the MID makes me wonder). You won't brick, you will just get error ouputs if it doesn't
Download this RUU.zip
Rename it to 0P6BIMG.zip (that's a zero, not the letter) and place it onto the root of your extSD.
Boot into bootloader and select hboot if it doesn't do that automatically.
Follow the prompts (vol up to flash, power button to reboot)
That's it.
After you are done make sure to delete the renamed file from your SD card, otherwise every time you boot to bootloader it will try tro update again.
Good luck!

xunholyx said:
I'm not sure that Lollipop is even available for the Middle East/Egyptian model. Your best bet would be to spend $25 for Sunshine S-Off, convert to superCID, and update with WWE/International firmware. You could also try to change your MID to 0P6B10000 and update that way, but there is a very real risk of bricking if you do that.
---------- Post added at 07:48 PM ---------- Previous post was at 07:22 PM ----------
You could also try this. No guarantees that it will work, but it might (your CID is listed as compatible, but the MID makes me wonder). You won't brick, you will just get error ouputs if it doesn't
Download this RUU.zip
Rename it to 0P6BIMG.zip (that's a zero, not the letter) and place it onto the root of your extSD.
Boot into bootloader and select hboot if it doesn't do that automatically.
Follow the prompts (vol up to flash, power button to reboot)
That's it.
After you are done make sure to delete the renamed file from your SD card, otherwise every time you boot to bootloader it will try tro update again.
Good luck!
Click to expand...
Click to collapse
thank you so much bro .
i will try that RUU and see if it worked and let you know. but i have a few questions .
1-do you think that update will effect on the radio or IMEI number ??
2-do i receive updates in the future ??
thanks again for helping me .

kirkuk said:
thank you so much bro .
i will try that RUU and see if it worked and let you know. but i have a few questions .
1-do you think that update will effect on the radio or IMEI number ??
2-do i receive updates in the future ??
thanks again for helping me .
Click to expand...
Click to collapse
Your radio version is the same as mine, and I'm on WWE so there is nothing to worry about there. You won't receive OTA updates MID. You can still update via RUU when the next version comes out, or you can get S-Off and just flash the firmware. I should have already let you know; and I am sorry that I forgot to mention it; but the RUU will wipe your phone so make sure you backup everything that is important to you. Make a backup to your extSD. That won't get wiped.

xunholyx said:
Your radio version is the same as mine, and I'm on WWE so there is nothing to worry about there. You won't receive OTA updates MID. You can still update via RUU when the next version comes out, or you can get S-Off and just flash the firmware. I should have already let you know; and I am sorry that I forgot to mention it; but the RUU will wipe your phone so make sure you backup everything that is important to you. Make a backup to your extSD. That won't get wiped.
Click to expand...
Click to collapse
a very big thanks to you bro i bothered you with my problem and questions and appreciate every word you wrote .it is ok that you didnot mentioned it will wipe my phone because i backed it up before .

xunholyx said:
Your radio version is the same as mine, and I'm on WWE so there is nothing to worry about there. You won't receive OTA updates MID. You can still update via RUU when the next version comes out, or you can get S-Off and just flash the firmware. I should have already let you know; and I am sorry that I forgot to mention it; but the RUU will wipe your phone so make sure you backup everything that is important to you. Make a backup to your extSD. That won't get wiped.
Click to expand...
Click to collapse
Hi. I don't mean to hijack this post or whatever but I have the same problem with the same MID and CID. I bought the phone from Riyadh and I am not receiving any OTA. I tried that RUU and it failed giving me the following error:
Code:
Model ID incorrect!
Update Fail!
Device halted due to Large Image update fail!
Press <POWER> to reboot.
EDIT: I did get the Stagefright fix by OTA if that helps somehow.

muftiazan said:
Hi. I don't mean to hijack this post or whatever but I have the same problem with the same MID and CID. I bought the phone from Riyadh and I am not receiving any OTA. I tried that RUU and it failed giving me the following error:
Code:
Model ID incorrect!
Update Fail!
Device halted due to Large Image update fail!
Press <POWER> to reboot.
EDIT: I did get the Stagefright fix by OTA if that helps somehow.
Click to expand...
Click to collapse
Yeah, I had a feeling that might happen.

xunholyx said:
Yeah, I had a feeling that might happen.
Click to expand...
Click to collapse
if i got same error did my phone will start as nothing happend and boots normal or i have to install new rom ??

kirkuk said:
if i got same error did my phone will start as nothing happend and boots normal or i have to install new rom ??
Click to expand...
Click to collapse
It'll boot up fine. Don't worry.

xunholyx said:
It'll boot up fine. Don't worry.
Click to expand...
Click to collapse
bro its failed and i got the same error as mentioned above . my device boot normal.thank you.

I hava the same problem. The Ruu you just provided was from the htc official rom downloads page right?
And, will this model effect the custom roms to be flashed?like would i be able to flash arhd on it (the same mid as OP and unlocked) without bricking it?
I thought samsung's variantd were insane but htc is driving me nuts ?

eatsleep said:
I hava the same problem. The Ruu you just provided was from the htc official rom downloads page right?
And, will this model effect the custom roms to be flashed?like would i be able to flash arhd on it (the same mid as OP and unlocked) without bricking it?
I thought samsung's variantd were insane but htc is driving me nuts ��
Click to expand...
Click to collapse
bro i am new to htc so i donot know much about htc and installing roms because i switched from samsung to htc . i think that RUU was official from htc but its failed to install on my htc one m8 because my device is made for middle east .i donot know if you can install it on your device or install custom roms on it .

eatsleep said:
I hava the same problem. The Ruu you just provided was from the htc official rom downloads page right?
And, will this model effect the custom roms to be flashed?like would i be able to flash arhd on it (the same mid as OP and unlocked) without bricking it?
I thought samsung's variantd were insane but htc is driving me nuts ��
Click to expand...
Click to collapse
It's a zip made from the official RUU.
It won't affect which ROMs you can flash.
If you have the same model as the OP, it won't work. You will need to get S-Off and change your MID first.

xunholyx said:
It'll boot up fine. Don't worry.
Click to expand...
Click to collapse
sorry bro for bothering you but is it safe to try this RUU
http://www.htc.com/us/support/htc-one-m8/news/
from htc website to update my phone ?? what happens if it fail to update ??

Hi there ...i have recived official OTA update android (5.0.2) in 11/26/2015 . Thanks to all of you .

kirkuk said:
sorry bro for bothering you but is it safe to try this RUU
http://www.htc.com/us/support/htc-one-m8/news/
from htc website to update my phone ?? what happens if it fail to update ??
Click to expand...
Click to collapse
I see you issue solved itself. But just FYI, the above RUU would not have worked on your phone. You can't just run any RUU, it needs to match your carrier ID (CID) and model ID (MID). You can change CID and MID, but only with s-off.

redpoint73 said:
I see you issue solved itself. But just FYI, the above RUU would not have worked on your phone. You can't just run any RUU, it needs to match your carrier ID (CID) and model ID (MID). You can change CID and MID, but only with s-off.
Click to expand...
Click to collapse
thank u for sharing us your experience .. the above RUU did not installed on my phone for the reasons that you wrote above ..i will try change the CID and MID to change my phone to GPE in the future if my phone not received the marshmallow update ...

i want 3.36.401.4 stock recovery my phone is rooted and i have the ota update so my phone is not updating

Can i Update my OS with S-ON?

hello guys i have an AT&T rooted htc one m8 with android 4.4.4, I once got my phone with s-off and updated to an official rom but now is s-on (still rooted) but i want to try an OS that can make a use of the band (3G 900MHz and 4G 1800MHz) because the rom i have from AT&T doesn't have the 3G 900MHz so my phone is either "4g" and "E" i don't have any 3g or h+
so can i install another (EMEA or ASIA OS) so i can get this bands working and all this by S-ON
(I live in venezuela so i can't buy the 25$ sunshine thing even if i have money because the government wont give us a dime to buy things in usd *sigh*)

You should update your firmware/OS to 4.28.502.2 first before you try other thing.
You can read How-To and link to RUU 4.28.502.2 here : http://forum.xda-developers.com/showthread.php?t=2751432
Then after, you can install TWRP 2.8.7.0 and make backup of your current ROM then try install other ROM and see whether you'll get what you want.
I remember I tried AT&T radio on my Asia WWE ROM, I don't have problem with 3G

i think i cant because I need to flash a different radio and i need to be S-OFF

This is a direct continuation of the thread you started here: http://forum.xda-developers.com/htc-one-m8/help/modify-set-band-htc-one-m8-att-t3286190
You should not have started a new thread. This just confuses those trying to help, and will lead to you getting confused also.
---------- Post added at 10:05 AM ---------- Previous post was at 10:03 AM ----------
mabf000 said:
but i want to try an OS that can make a use of the band (3G 900MHz and 4G 1800MHz) because the rom i have from AT&T doesn't have the 3G 900MHz
Click to expand...
Click to collapse
OS has nothing to do with band support.
You are confusing the term "firmware" with OS. Please erase from your brain that these 2 things are the same. On this device, "firmware" refers to specific partitions, separate from the OS (ROM). Firmware (specifically the radio baseband, which is contained in firmware) has nothing to do with the OS (ROM). Changing the OS will not change your band support.
I already told you how to change the firmware in your other thread. Now it sounds like you are trying to do something different. Although its not clear, since you have jumped to a new thread.
---------- Post added at 10:09 AM ---------- Previous post was at 10:05 AM ----------
mabf000 said:
I once got my phone with s-off and updated to an official rom but now is s-on (still rooted)
Click to expand...
Click to collapse
The only way the phone would have been made s-on again (after being s-off) is if you changed it manually.
Something doesn't make sense here. Are you sure it was s-off?
Do a fastboot getvar all, and post the output (delete IMEI and serial number before posting, as these are personal info).
mabf000 said:
so can i install another (EMEA or ASIA OS) so i can get this bands working and all this by S-ON
Click to expand...
Click to collapse
I already stated in your other thread, that s-off is required to change band support. Why are you asking if you can do it s-on? Obviously, the answer is NO.
This is one of the reasons you need to stick to one thread, and not make new ones for the same exact questions/issue.
mabf000 said:
(I live in venezuela so i can't buy the 25$ sunshine thing even if i have money because the government wont give us a dime to buy things in usd *sigh*)
Click to expand...
Click to collapse
What does the government have to do with making a small credit card purchase?
When you make a credit card purchase, it gets automatically converted to your local currency. Currency is currency, the purchase doesn't have to be made in US dollars.

One note - if the phone was ever S-off'ed via Sunshine, it may still have a valid device license. You might just try running Sunshine again and see if it asks for payment.

redpoint73 said:
This is a direct continuation of the thread you started here: http://forum.xda-developers.com/htc-one-m8/help/modify-set-band-htc-one-m8-att-t3286190
You should not have started a new thread. This just confuses those trying to help, and will lead to you getting confused also.
---------- Post added at 10:05 AM ---------- Previous post was at 10:03 AM ----------
OS has nothing to do with band support.
You are confusing the term "firmware" with OS. Please erase from your brain that these 2 things are the same. On this device, "firmware" refers to specific partitions, separate from the OS (ROM). Firmware (specifically the radio baseband, which is contained in firmware) has nothing to do with the OS (ROM). Changing the OS will not change your band support.
I already told you how to change the firmware in your other thread. Now it sounds like you are trying to do something different. Although its not clear, since you have jumped to a new thread.
---------- Post added at 10:09 AM ---------- Previous post was at 10:05 AM ----------
The only way the phone would have been made s-on again (after being s-off) is if you changed it manually.
Something doesn't make sense here. Are you sure it was s-off?
Do a fastboot getvar all, and post the output (delete IMEI and serial number before posting, as these are personal info).
I already stated in your other thread, that s-off is required to change band support. Why are you asking if you can do it s-on? Obviously, the answer is NO.
This is one of the reasons you need to stick to one thread, and not make new ones for the same exact questions/issue.
What does the government have to do with making a small credit card purchase?
When you make a credit card purchase, it gets automatically converted to your local currency. Currency is currency, the purchase doesn't have to be made in US dollars.
Click to expand...
Click to collapse
yeah im sorry to open a new thread to this i was very confused,
now this is what i get to the fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: [email protected]
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B12000
(bootloader) cidnum: CWS__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 56f9ae32
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.049s
i think my phone never was S-OFF i was thinking about it and i never did it before, i think the only way to get all my bands working is getting the phone s-off and flash it anothe radio version, and i dont know what happens when im trying to install the AT&T rom from htc website cuz RUU always gives me an error, I cant get supercid it gives me an error so i think all my problems are because im s-on =(
and i want to buy the license to sunshine but in venezuela that's almost impossible, you should read more about venezuela government right now its insane

mabf000 said:
i think my phone never was S-OFF i was thinking about it and i never did it before
Click to expand...
Click to collapse
This isn't something you should "think" or not. It either was s-off by sunshine, or it was never s-off. You need to get your facts straight, and provide the correct information, otherwise nobody here can do a thing to help you.
mabf000 said:
i think the only way to get all my bands working is getting the phone s-off and flash it anothe radio version,
Click to expand...
Click to collapse
I've already stated definitively and emphatically, that you can only change band support (flash another radio) with s-off.
I don't understand why you continue to question this, or say "I think". Its irrelavent what you "think", what I've told you is fact.
I'm sorry if I sound annoyed; since, well . . . I am annoyed. But I have little patience for folks that can't follow instructions, or accept simple advice given to them.
mabf000 said:
i dont know what happens when im trying to install the AT&T rom from htc website cuz RUU always gives me an error, I cant get supercid it gives me an error so i think all my problems are because im s-on =(
Click to expand...
Click to collapse
RUU runs fine with s-on. Its designed for stock devices.
On the bootloader screen, does it say LOCKED, UNLOCKED, or RELOCKED near the top of the screen?
Although the RUU will just update the OS version, it is not going to change the band support.
mabf000 said:
and i want to buy the license to sunshine but in venezuela that's almost impossible, you should read more about venezuela government right now its insane
Click to expand...
Click to collapse
I'm not interested in the details. Either its possible or not possible to buy a sunshine license. I don't know what "almost impossible" means.
The sunshine devs are usually willing to accept alternate payment methods (such as buying a gift card); due to difficulties paying in some countries. If you want to change band support, I'd suggest contact the sunshine team, and see what they can do with you.
Otherwise, stop fantasizing there is a way to change band support with s-on; since its not possible.

redpoint73 said:
RUU runs fine with s-on. Its designed for stock devices.
On the bootloader screen, does it say LOCKED, UNLOCKED, or RELOCKED near the top of the screen?
Although the RUU will just update the OS version, it is not going to change the band support.
Click to expand...
Click to collapse
it says *** UNLOCKED ***
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: [email protected]
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B12000
(bootloader) cidnum: CWS__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 56f9ae32
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.041s
i downloaded the latest RUU from htc website to my at&t and I always get error 155

mabf000 said:
it says *** UNLOCKED ***
i downloaded the latest RUU from htc website to my at&t and I always get error 155
Click to expand...
Click to collapse
As you should. With s-on, you need to relock the bootloader in order to RUU. Relock the bootloader with fastboot command:
fastboot oem lock
After you RUU, you can unlock the bootloader again (if you wish) either by using the unlock bin code from the first time you unlocked; which doesn't always work, so many folks have had to just go through HTCDev.com to get a new bin code.
Then install TWRP, root, etc.
Also, there was no need to post your getvar data again. It wasn't asked for, it doesn't contain the bootloader status (which is why I asked for it separately) and unless anything has changed (doesn't appear so) its just redundant. Most folks here are actually good at reading what has already been posted.

thank you so much and Im really sorry if I annoyed you, im really a noob with all of this

mabf000 said:
thank you so much
Click to expand...
Click to collapse
There' s a button for that.
mabf000 said:
Im really sorry if I annoyed you, im really a noob with all of this
Click to expand...
Click to collapse
No worries. Just try to post more carefully in the future. Take a moment to think if its really necessary to create a new post, ask the same question you just asked, or post the same info you just post. In most cases, the answer will be NO.
I can understand wanting to be sure about things, or wanting more opinions. But the way you went about it was all wrong.

redpoint73 said:
There' s a button for that.
No worries. Just try to post more carefully in the future. Take a moment to think if its really necessary to create a new post, ask the same question you just asked, or post the same info you just post. In most cases, the answer will be NO.
I can understand wanting to be sure about things, or wanting more opinions. But the way you went about it was all wrong.
Click to expand...
Click to collapse
hi there again, ok i got my device s-off and change the cid to supercid and the mid to the at&t what is the next step to flash the radio to get all my bands working, you already say that the emea or the asian but i got lost there where i can find them and how can i flash it? need some help with that

mabf000 said:
hi there again, ok i got my device s-off and change the cid to supercid and the mid to the at&t
Click to expand...
Click to collapse
What do you mean you changed the MID to AT&T? It was already the AT&T MID, since you have the AT&T device.

redpoint73 said:
What do you mean you changed the MID to AT&T? It was already the AT&T MID, since you have the AT&T device.
Click to expand...
Click to collapse
yes i did notice that, so i didnt change the mid but i actually flash this ruu (RUU_M8_UL_L50_SENSE60_MR_HTC_Europe_4.16.401.10_Radio_1.25.214500021.06G_20.68.4196t.01_F_release_417003_signed)
thats the europe version (i think) but i cant get my at&t device to get 3g or h+

You're hopping back and forth between this thread, and the other one you started: http://forum.xda-developers.com/htc-one-m8/help/modify-set-band-htc-one-m8-att-t3286190/post64980222#post64980222
Makes it super confusing what the sequence of the steps you tried, latest current condition, and what is working and what is not.
Pick one thread, and stick to it. Do not bounce back and forth.

And here is another one that related - http://forum.xda-developers.com/htc-one-m8/help/red-triangle-trying-to-update-firmware-t3301484

deleted OS, been trying to return to stock

So I've been reading a ton of these threads to try to help me fix this. It seems like a really easy fix but it's not working for me. My device cid is htc__01 and I'm S-On. I'm trying to do an HBoot of the nandroid zip for my cid that I got from https://forum.xda-developers.com/showthread.php?t=2701376.
I downloaded the "4.16.401.10 - TWRP Thanks to Clumsy" under CID HTC__01 of nandroid backups. I put it on my SD card and I renamed it to 0P6BIMG.zip.
My HBoot is 3.19 btw. When I start HBoot, it says "no image or wrong image"
I'm also currently "unlocked" but I also tried running HBoot when I was "relocked" and it didn't work.
Any tips?
edit: Here are some pictures to show what I'm getting and what my info is
http://i.imgur.com/dsISZpB.jpg
http://i.imgur.com/IekCgFp.jpg

You do it all wrong ... the nandroid backup zip is to be extracted and restored not renamed and flashed.
Read this post #1 on how to use a nandroid to restore to stock - https://forum.xda-developers.com/htc-one-m8/help/tutorial-how-to-stock-stock-twrp-t3086860
If you want the RUU.zip that can be renamed 0P6BIMG.zip and flash via hboot,
you need this - https://forum.xda-developers.com/showpost.php?p=64926626&postcount=6
but this will get your device updated to Marsmallow directly.
Just saw your EDIT - Forget the above ... you have a AT&T device ... you'll need AT&T RUU
Can you post fastboot getvar all result (without serial & imei no.), need to see what's your device current status ... still an AT&T or converted to Intl GSM.

ckpv5 said:
You do it all wrong ... the nandroid backup zip is to be extracted and restored not renamed and flashed.
Read this post #1 on how to use a nandroid to restore to stock - https://forum.xda-developers.com/htc-one-m8/help/tutorial-how-to-stock-stock-twrp-t3086860
If you want the RUU.zip that can be renamed 0P6BIMG.zip and flash via hboot,
you need this - https://forum.xda-developers.com/showpost.php?p=64926626&postcount=6
but this will get your device updated to Marsmallow directly.
Just saw your EDIT - Forget the above ... you have a AT&T device ... you'll need AT&T RUU
Can you post fastboot getvar all result (without serial & imei no.), need to see what's your device current status ... still an AT&T or converted to Intl GSM.
Click to expand...
Click to collapse
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: [email protected]
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:-
(bootloader) imei: -
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B12000
(bootloader) cidnum: CWS__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 7f8e91a3
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.342s

refsner said:
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: [email protected]
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B12000
(bootloader) cidnum: CWS__001
(bootloader) security: on
Click to expand...
Click to collapse
You do have a AT&T device.
The best place for your reference is @redpoint73 thread - https://forum.xda-developers.com/showthread.php?t=2751432
Are you in US and on AT&T network ?
If yes .. to get back to stock and updated to Marshmallow, you can follow this guide - https://forum.xda-developers.com/showpost.php?p=67123738&postcount=7

ckpv5 said:
You do have a AT&T device.
The best place for your reference is @redpoint73 thread - https://forum.xda-developers.com/showthread.php?t=2751432
Are you in US and on AT&T network ?
If yes .. to get back to stock and updated to Marshmallow, you can follow this guide - https://forum.xda-developers.com/showpost.php?p=67123738&postcount=7
Click to expand...
Click to collapse
Yes I'm in the US but I'm using an AT&T phone with T-Mobile network. So would I need to follow the other steps in your second thread linked?

refsner said:
Yes I'm in the US but I'm using an AT&T phone with T-Mobile network. So would I need to follow the other steps in your second thread linked?
Click to expand...
Click to collapse
If you want a Masrhamallow stock ROM, yes the second thread. But I'm not sure about the SIM lock status of AT&T and the AT&T HD Voice whether these will impact your network on T-Mobile.
Need someone familiar with AT&T like @redpoint73 to comment.
I suggest you to wait for other comments.
Meantime - you can restore nandroid backup 4.28.502.2 which available on my backup thread to have a working phone. Don't do any RUU install yet.
EDIT - based on your screenshots/getvar result - you have a KitKat firmware, restore 3.42.502.1 to have a working phone. The above backup, you'll have wifi problem because that's a Lollipop.

ckpv5 said:
If you want a Masrhamallow stock ROM, yes the second thread. But I'm not sure about the SIM lock status of AT&T and the AT&T HD Voice whether these will impact your network on T-Mobile.
Need someone familiar with AT&T like @redpoint73 to comment.
I suggest you to wait for other comments.
Meantime - you can restore nandroid backup 4.28.502.2 which available on my backup thread to have a working phone. Don't do any RUU install yet.
Click to expand...
Click to collapse
Got it I'll do that. Thank for helping me out

refsner said:
Got it I'll do that. Thank for helping me out
Click to expand...
Click to collapse
Read my edit - you have a KitKat firmware, restore 3.42.502.1

ckpv5 said:
Read my edit - you have a KitKat firmware, restore 3.42.502.1
Click to expand...
Click to collapse
Ok! Will I be able to update to marshmallow at all afterwards?

refsner said:
Ok! Will I be able to update to marshmallow at all afterwards?
Click to expand...
Click to collapse
You won't be able to OTA when not on AT&T but you can get to Marshmallow using the guide that I put here - https://forum.xda-developers.com/showpost.php?p=67123738&postcount=7
The only thing that I'm not sure whether the phone is SIM locked to AT&T or not.
If you're sure it is not SIM locked, you can straight away follow the guide.
Or if it is SIM locked but you do have the SIM unlock code .. then go ahead with the Marshmallow RUU.
About the HD Voice, I believe that will affect users on AT&T network but running custom ROM.

ckpv5 said:
You won't be able to OTA when not on AT&T but you can get to Marshmallow using the guide that I put here - https://forum.xda-developers.com/showpost.php?p=67123738&postcount=7
The only thing that I'm not sure whether the phone is SIM locked to AT&T or not.
If you're sure it is not SIM locked, you can straight away follow the guide.
Or if it is SIM locked but you do have the SIM unlock code .. then go ahead with the Marshmallow RUU.
About the HD Voice, I believe that will affect users on AT&T network but running custom ROM.
Click to expand...
Click to collapse
I think the first time I received the phone, it was SIM locked but I was able to get a SIM unlock code. I'll place my bets and do the Marshmallow RUU. I'll let you know if it goes well.

refsner said:
I think the first time I received the phone, it was SIM locked but I was able to get a SIM unlock code. I'll place my bets and do the Marshmallow RUU. I'll let you know if it goes well.
Click to expand...
Click to collapse
Ok
Another thing is your device is S-On, you need to relock bootloader before you install the firmware.zip and RUU.
You already know how I believe - fastboot oem lock

ckpv5 said:
Ok
Another thing is your device is S-On, you need to relock bootloader before you install the firmware.zip and RUU.
You already know how I believe - fastboot oem lock
Click to expand...
Click to collapse
Yeah I made sure to do that thank you. I'm in the process of installing the RUU right now. Going a little slow. The RUU says to turn on the phone. Does that mean put it into fastboot USB? It didn't work when I had it just on the HTC logo white screen.

Yes - put the device on fastboot mode.
You already did the firmware installation ?
Install firmware first then RUU - all these on fastboot mode

ckpv5 said:
Yes - put the device on fastboot mode.
You already did the firmware installation ?
Install firmware first then RUU - all these on fastboot mode
Click to expand...
Click to collapse
Yes I did the firmware installation first. Then I ran the RUU, this time on fastboot mode (haha). It is still in the process of updating right now.
Edit: It's starting up. Seems to have worked. I appreciate all your help. I would have probably spent many more hours trying to figure this mess out!

refsner said:
Edit: It's starting up. Seems to have worked.
Click to expand...
Click to collapse
:good:
So no problem with SIM as it is still remain unlocked ? Hopefully yes as usually once SIM is unlocked it should remain unlocked.

ckpv5 said:
:good:
So no problem with SIM as it is still remain unlocked ? Hopefully yes as usually once SIM is unlocked it should remain unlocked.
Click to expand...
Click to collapse
No there was no problem at all. I inserted the SIM card and immediately got LTE T-Mobile coverage. Super fortunate

refsner said:
No there was no problem at all. I inserted the SIM card and immediately got LTE T-Mobile coverage. Super fortunate
Click to expand...
Click to collapse
Great .. this will be a good reference for someone else on same situation.

ckpv5 said:
Need someone familiar with AT&T like @redpoint73 to comment.
I suggest you to wait for other comments.
Click to expand...
Click to collapse
Looks like ckpv5 has the OP sorted out, before I even woke up! :good:
But let me know, if there are any further AT&T specific questions.

Hi guys anybody can help me ? My Htc one m8 has been bricked i can't flash stock ruu

Hi guys anybody can help me ? My Htc one m8 has been bricked i can't flash stock ruu please help me
this are my fastboot getvar all value :
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.24_2G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.20.709.2
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: *****
(bootloader) imei: ******
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 205bdca3
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.008s
so my bootlader is locked with security warning and software status : modified

Which RUU did your try (version number, file name)? And what does that mean you "can't flash stock ruu"? Did you get any error messages, what point did it fail, etc.?
You also need to tell us how it is "bricked"? Were you trying to flash something, or update, etc.? Or just happened on its own (failed to boot to OS)?
Did you do any mods to the phone, or is it (as far as you know) stock? For that matter, did you get the phone used?

redpoint73 said:
Which RUU did your try (version number, file name)? And what does that mean you "can't flash stock ruu"? Did you get any error messages, what point did it fail, etc.?
You also need to tell us how it is "bricked"? Were you trying to flash something, or update, etc.? Or just happened on its own (failed to boot to OS)?
Did you do any mods to the phone, or is it (as far as you know) stock? For that matter, did you get the phone used?
Click to expand...
Click to collapse
When i flash RUU faced with "remote : 12 signautre verify fail" and this is a RUU that i flashed : HTC One M8 6.20.709.2 sense 8

redpoint73 said:
Which RUU did your try (version number, file name)? And what does that mean you "can't flash stock ruu"? Did you get any error messages, what point did it fail, etc.?
You also need to tell us how it is "bricked"? Were you trying to flash something, or update, etc.? Or just happened on its own (failed to boot to OS)?
Did you do any mods to the phone, or is it (as far as you know) stock? For that matter, did you get the phone used?
Click to expand...
Click to collapse
when i unplugged the phone from charger this problem occurred i didn't flash any RUU later and my phone is unrooted .

mamali0067 said:
when i unplugged the phone from charger this problem occurred .
Click to expand...
Click to collapse
I assume when you say "bricked" it means you can't boot to Android OS, but you can get to bootloader (otherwise, you wouldn't have been able to do fastboot getvar).
On the bootloader screen, does it say LOCKED or UNLOCKED near the top?
Also, I recommend you delete IMEI and serial number from your top post. These are personal info, and should not be posted online (and also, not needed to help or advise you).
---------- Post added at 09:09 AM ---------- Previous post was at 09:09 AM ----------
mamali0067 said:
When i flash RUU faced with "remote : 12 signautre verify fail" and this is a RUU that i flashed : HTC One M8 6.20.709.2 sense 8
Click to expand...
Click to collapse
To confirm, the file actually says "RUU" in the file name, and about 1.5 GB in size?

redpoint73 said:
I assume when you say "bricked" it means you can't boot to Android OS, but you can get to bootloader (otherwise, you wouldn't have been able to do fastboot getvar).
On the bootloader screen, does it say LOCKED or UNLOCKED near the top?
Also, I recommend you delete IMEI and serial number from your top post. These are personal info, and should not be posted online (and also, not needed to help or advise you).
---------- Post added at 09:09 AM ---------- Previous post was at 09:09 AM ----------
To confirm, the file actually says "RUU" in the file name, and about 1.5 GB in size?
Click to expand...
Click to collapse
yes of course it's about 1.6 GB and in my bootloader it say LOCKED

mamali0067 said:
yes of course it's about 1.6 GB and in my bootloader it say LOCKED
Click to expand...
Click to collapse
Is this a zip format RUU? If so, cut/paste the exact commands you used.

redpoint73 said:
Is this a zip format RUU? If so, cut/paste the exact commands you used.
Click to expand...
Click to collapse
yes the RUU is a zip file , but i flashed that RUU perefer in finding right RUU thread and faced with remote : 12 signature verify fail

mamali0067 said:
i flashed that RUU perefer in finding right RUU thread
Click to expand...
Click to collapse
I'm not going to jump around threads looking for the info. I already told you that twice. You should be trying to make it easier for folks to help you, not harder!

redpoint73 said:
I'm not going to jump around threads looking for the info. I already told you that twice. You should be trying to make it easier for folks to help you, not harder!
Click to expand...
Click to collapse
Okay dude , so help me here !

mamali0067 said:
Okay dude , so help me here !
Click to expand...
Click to collapse
You didn't provide the info I asked for: cut/paste the exact commands you used

redpoint73 said:
You didn't provide the info I asked for: cut/paste the exact commands you used
Click to expand...
Click to collapse
Yes , I have been cutted and pasted the command