Hi all, my S4 mini won't turn on, while i was messaging, the display shutting down and can't turn on it.
When i connected it to my pc, my pc found new driver: QHSUSB_DLOAD. I searched it on google and i discovered that my phone was bricked without doing anything. So i flashed a sdcard with debrick.img and my phone finally showed:
Code:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS. .
BOOT RECOVERY
WRITE 139008 sectors
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: GT-i9195
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANT VOID: 0x0
CSB-CONFIG-LSB: 0x30
BOOTLOADER RP SWREV: 2
WRITE PROTECTION: Enable
So i tried to flash it with Odin and after Odin said:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_shi p_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULT I_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_M ULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
So i searched on internet PIT files and i found "CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit", i tried to flash with it and Odin show same thing:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
While on the phone showed:
Code:
PIT FAIL : TOTAL SECTORS 0
ODIN flash read failure
I tried nand flash erase and show me other errors.
I think emmc died, if not, can anyone help me?
if emmc died, how can i install all partition ( bootloader ecc.) on sdcard for start the phone with it?
Have exact same fault, so do others.
Be nice to know if this is hardware or soft fault and possible remedy.
Related
Hello!
I have problem with GT-I9195.
It was hardbricked. I unbricked it with SDcard and debrick.img. Now I have bootloop problem. I put phone to download mode and flash with stock ROM but it has bootloop again and there is No command in Recovery Mode. I tried to install Custom Recovery and still same No Command.
I tried this method:
(file names starting with: )
Bootloader (BL) > BOOTLOADER...
PDA (AP) > CODE...
PHONE (CP) > MODEM...
CSC > CSC...
PIT > CSB...
I get this error:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
This is Status in Download mode:
ODIN MODE
PRODUCT NAME: GT-I9195
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
BOOTLOADER AP SWREV: 2
WRITE PROTECTION: Enable
And on FAIL! (Auth) Error
SW REV CHECK FAIL: Fused 2 > Binary 1
Can anyone help me?
I have a Galaxy S3 Tmobile - not rooted. I wiped my phone to default and when it tried to power on, it gave me couldn't mount e:\ - don't remember the exact path. After attempting to flash with stock firmware T999UVDMD5_T999TMBDMD5_TMB and 16GB.pit file with odin 3.04 and 3.07 that failed:
Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone:
ODIN MODE
Product Name: SGH-T999L
CUSTOM BINARY DOWNLOAD: Yes (1 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit; 0
BOOTLOADER Bit: 0
SECURE CHECK FAIL: PIT
Thanks in advance!
Try flashing without the PIT file?
audit13 said:
Try flashing without the PIT file?
Click to expand...
Click to collapse
I've tried that but it still fails:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVUENC2_T999TMBENC2_T999UVUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Which bootloader is on the phone? Are the error messages from Odin 3.07? Are you unchecking everything except f.reset time and auto reboot in Odin?
I had CM13
I used the option of extending the internal memory through the SD card if that's important
Now I've tried going back to stock, but I got a message that there is a problem with the md4 file.
I then tried to work with the full set of files (PIT, BL, CSC, etc.)
I get this on Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_shi p_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULT I_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MUL TI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_M ULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> sbl1.mbn
<ID:0/009> NAND Write Start!!
<ID:0/009> sbl2.mbn
<ID:0/009> sbl3.mbn
<ID:0/009> aboot.mbn
<ID:0/009> FAIL! (Auth)
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and on the phone I get
SW REV CHECK FAIL : Fused 2 > Binary 1
What can I do?
Thanks
my a3 was having issues, and after a few mistakes i ended up with no os on the phone, TWRP is installed.
Ive tried countless times to flash a stock ROM using odin and im just about ready to pull my hair out.
heres whats on my screen when in download mode:
current binary: samsung official
system status: custom
FRP lock: off
secure download : enabled
CCIC: S2MU004
warranty void: 1 (0x030c)
RP SWREV : B5 K3 S3
this is all the stuff from ODIN:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1401)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 4287 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> param.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and when i try to flash the error on my phone is SW REV. CHECKFAIL (BOOTLOADER) DEVICE 5 BINARY 4
if anyone could help me i would greatly appreciate it, thanks in advance.
Your firmware which you trying installing is latest oreo firmware with all latest secury patches? I had similar issue when my a3 had installed oreo with all updates and i was trying to install older oreo firmware and odin failed everytime. Then i decided to download latest oreo firmware and latest firmware flashed without any issues.
Try latest firmware it will work and donot play with pit just flash firmware bl cp ap and simple scs instead of home scs
---------- Post added at 03:19 PM ---------- Previous post was at 03:14 PM ----------
Try latest firmware it will work and donot play with pit just flash firmware bl cp ap and simple scs instead of home scs
I can't flash my Samsung A320 (A3 23017) with the original firmware usin Odin. I previously did the flash, but now Odin fails with the exact firmware I used before. I rooted the device with TWRP to rid some bloatware before and now my second attempt to flash fails. Any suggestions? Thanks
Here's the log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1401)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 4296 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> param.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
PS: I tried both clean and partial flash.
version of binary must be same or upper
A320FLXXS9CTK2 - binary 9