Related
I attempted to install recovery on my phone and everything seem to be going ok untill after saying yeah and now mu phone Is bricked.
I may rebooted it too early assuming it was done. How I can recover the phone? Or I just have to go to sprint store ?
I can put my phone in download mode
tritron777 said:
I attempted to install recovery on my phone and everything seem to be going ok untill after saying yeah and now mu phone Is bricked.
I may rebooted it too early assuming it was done. How I can recover the phone? Or I just have to go to sprint store ?
I can put my phone in download mode
Click to expand...
Click to collapse
I just went through a similar issue. Don't worry, if you can get to download mode, your phone should be recoverable.
The first thing you want to try is to flash your phone's original firmware. All of the instructions and downloads you need are located on the IRC server our developers use. Check out the link below for instructions on getting into IRC. You can use LGNPST to flash recovery (search forum for teenybin), or you can also just flash the unlocked stock firmware if you so choose. The guys in IRC are very helpful.
http://forum.xda-developers.com/showthread.php?t=1984620
If your phone still does not boot after using LGNPST, and you cannot get into recovery, let me know, you may need a battery pull.
Thank you for pointing me in right direction and thank you for the tip. I have my phone working and unlocked and rooted with custom firmware in less than 30 minutes.
Hello, I've spent about the past 5 days trying to figure this out. So, how this started was, a while back when I first got the phone, I wanted 4.4, so I rooted my phone, and tried to flashify a recovery like CWM and TWRP. Both of these failed. I tried many times, and no matter what I tried, flashing always failed. But guess what, my stock recovery was erased in the process. I forgot about it until today, where I found the OTA update to 4.4 was released, and attempted to do it. To my dismay, I forgot I had no recovery mode, and instantly got the "boot certification verify" error screen. Now All I can access is download mode, to my knowledge. So I've been trying to fix this, either by installing stock recovery, or another way to install a custom. All to no avail. When I use the lg flash tool for the stock recovery, it fails at "BIN CRC Check". Every.... Single.... Time. Despite downloading multiple replacement files. I would be perfectly content with installing a customer recovery, but the ways I see require the phone to be on, and use the built in recovery mode. At this point, my phone is bricked, and I am looking for any and all ways to either A) boot back up normally without installing a recovery and fix it later, or B) install a recovery, even if it's the hard way.
Update:
I followed this thread:
http://forum.xda-developers.com/showthread.php?t=2582142
It looked like it was going to work. I am using a Xubuntu virtual machine. I was copying the files over, and every time it finished copying a file, it unmounted and remounted my phone (I don't know if that was suppose to happen, just worth mentioning if it wasn't suppose to). I was super excited to do it. Hard rebooted my phone. And now it's just a blank screen. I have no logo, no error, and no download mode like I had before. Seriously need some help here.
Update#2:
I have the flash tool correctly working. Awesome! But..... I still have no download mode here.... So I can't use the tool....
Lastly, I am aware of the title.... i don't know how that happened. I intended to type "need", but somehow that happened. I do not know how to edit it.
Can you enter recovery?
Sent from my LG-LS980 using XDA Premium 4 mobile app
Ouch bud you are hard bricked pretty much. It sounds to me from what you explained all the partitions are wiped clean. I don't think there is any recovery from that unless you have a nand programmer
Sent from my LG-LS980 using xda app-developers app
brockzilla said:
Hello, I've spent about the past 5 days trying to figure this out. So, how this started was, a while back when I first got the phone, I wanted 4.4, so I rooted my phone, and tried to flashify a recovery like CWM and TWRP. Both of these failed. I tried many times, and no matter what I tried, flashing always failed. But guess what, my stock recovery was erased in the process. I forgot about it until today, where I found the OTA update to 4.4 was released, and attempted to do it. To my dismay, I forgot I had no recovery mode, and instantly got the "boot certification verify" error screen. Now All I can access is download mode, to my knowledge. So I've been trying to fix this, either by installing stock recovery, or another way to install a custom. All to no avail. When I use the lg flash tool for the stock recovery, it fails at "BIN CRC Check". Every.... Single.... Time. Despite downloading multiple replacement files. I would be perfectly content with installing a customer recovery, but the ways I see require the phone to be on, and use the built in recovery mode. At this point, my phone is bricked, and I am looking for any and all ways to either A) boot back up normally without installing a recovery and fix it later, or B) install a recovery, even if it's the hard way.
Update:
I followed this thread:
http://forum.xda-developers.com/showthread.php?t=2582142
It looked like it was going to work. I am using a Xubuntu virtual machine. I was copying the files over, and every time it finished copying a file, it unmounted and remounted my phone (I don't know if that was suppose to happen, just worth mentioning if it wasn't suppose to). I was super excited to do it. Hard rebooted my phone. And now it's just a blank screen. I have no logo, no error, and no download mode like I had before. Seriously need some help here.
Update#2:
I have the flash tool correctly working. Awesome! But..... I still have no download mode here.... So I can't use the tool....
Lastly, I am aware of the title.... i don't know how that happened. I intended to type "need", but somehow that happened. I do not know how to edit it.
Click to expand...
Click to collapse
Im confused you said you had download mode then didnt? If it works try using the alternate G2 dll named 8974, because the second time I used Flashtool only the alternate dll worked which is weird because just hours earlier I had used the original, the original said wrong model/download failed the second time.
abhinav.tella said:
Im confused you said you had download mode then didnt? If it works try using the alternate G2 dll named 8974, because the second time I used Flashtool only the alternate dll worked which is weird because just hours earlier I had used the original, the original said wrong model/download failed the second time.
Click to expand...
Click to collapse
As I explained in my update, the method I used didn't work and had removed all modes I could boot into, including download mode.
brockzilla said:
As I explained in my update, the method I used didn't work and had removed all modes I could boot into, including download mode.
Click to expand...
Click to collapse
Try this
http://forum.xda-developers.com/showthread.php?t=2477595
Then use LG Flash Tool, the Verizon guide works for LS980. Except use LS980 dll, and you must use Verizon USB drivers (Not T-Mobile, ATT etc), or Flash Tool wont work.
http://forum.xda-developers.com/showthread.php?t=2448960
I definitely hope you only semi bricked..... Tell me if that works.
brockzilla said:
As I explained in my update, the method I used didn't work and had removed all modes I could boot into, including download mode.
Click to expand...
Click to collapse
abhinav.tella said:
Try this
http://forum.xda-developers.com/showthread.php?t=2477595
Then use LG Flash Tool, the Verizon guide works for LS980. Except use LS980 dll, and you must use Verizon USB drivers (Not T-Mobile, ATT etc), or Flash Tool wont work.
http://forum.xda-developers.com/showthread.php?t=2448960
I definitely hope you only semi bricked..... Tell me if that works.
Click to expand...
Click to collapse
from what he said it sounds like a hard brick
Damn, not even fastboot? Feel sorry for you.
I was trying to carrier unlock my phone, and to do that i tried to downgrade it 4.3 to 4.1.1, and only after i had pressed the button, i had noticed that this might brick my phone in a comment in one of the forums, this is what i did:
http://forum.xda-developers.com/showthread.php?t=2625461
after following this and trying to run odin with it, odin returned "FAIL", and due to my high level of stupidity at the time, i tried to use the original 4.1.1 as my PDA in odin right after, i didnt reboot or anything, just pressed start again with the other tar.md5 file....
so now i cannot go past the samsung galaxy s3 logo when booting. I CAN go into download mode though, but i have no clue what i am supposed to do afterwards
i have the Galaxy S 3 i747 (was 4.3 before the whole mess) at&t carrier, i am trying to unlock it because i am travelling and need a phone.
please help me fix it, i do not care about the warranty since i dont have it anymore anyways, as long as the phone is working
also, if possible, i also need to unlock it afterwards, any help is HIGHLY appreciated, thanks!
baruchadi said:
I was trying to carrier unlock my phone, and to do that i tried to downgrade it 4.3 to 4.1.1, and only after i had pressed the button, i had noticed that this might brick my phone in a comment in one of the forums, this is what i did:
http://forum.xda-developers.com/showthread.php?t=2625461
after following this and trying to run odin with it, odin returned "FAIL", and due to my high level of stupidity at the time, i tried to use the original 4.1.1 as my PDA in odin right after, i didnt reboot or anything, just pressed start again with the other tar.md5 file....
so now i cannot go past the samsung galaxy s3 logo when booting. I CAN go into download mode though, but i have no clue what i am supposed to do afterwards
i have the Galaxy S 3 i747 (was 4.3 before the whole mess) at&t carrier, i am trying to unlock it because i am travelling and need a phone.
please help me fix it, i do not care about the warranty since i dont have it anymore anyways, as long as the phone is working
also, if possible, i also need to unlock it afterwards, any help is HIGHLY appreciated, thanks!
Click to expand...
Click to collapse
Downgrading your boot loader from 4.3 is a guaranteed brick. I'm not sure if the brick will get you to the Samsung screen.
If you're already assuming its bricked reboot into recovery and do a full wipe. Restore a nandroid of something if you have one or try flashing a custom ROM. Because Odin failed maybe it never flashed the boot loader.
Worth a try
Sent from my SGH-I747M using XDA Free mobile app
baruchadi said:
I was trying to carrier unlock my phone, and to do that i tried to downgrade it 4.3 to 4.1.1, and only after i had pressed the button, i had noticed that this might brick my phone in a comment in one of the forums, this is what i did:
http://forum.xda-developers.com/showthread.php?t=2625461
after following this and trying to run odin with it, odin returned "FAIL", and due to my high level of stupidity at the time, i tried to use the original 4.1.1 as my PDA in odin right after, i didnt reboot or anything, just pressed start again with the other tar.md5 file....
so now i cannot go past the samsung galaxy s3 logo when booting. I CAN go into download mode though, but i have no clue what i am supposed to do afterwards
i have the Galaxy S 3 i747 (was 4.3 before the whole mess) at&t carrier, i am trying to unlock it because i am travelling and need a phone.
please help me fix it, i do not care about the warranty since i dont have it anymore anyways, as long as the phone is working
also, if possible, i also need to unlock it afterwards, any help is HIGHLY appreciated, thanks!
Click to expand...
Click to collapse
Welcome to the forum! Wished you'd come in much earlier though as you would have found you CANNOT downgrade from 4.3 to 4.1.1 to free unlock. Sorry, but once you are on 4.3, the surest way to unlock is to obtain the unlock code from the carrier or purchase one online. Sounds like you do have a soft brick. If your phone is still booting to the Samsung logo, then it's only a soft brick. Attempting to downgrade the 4.3 bootloader usually results in a hard brick so you may be in luck.
To fix this first, try to see if you can boot to recovery mode and do a hard wipe/factory reset. If you are able to boot to recovery (or download) mode then you have little to worry about. If the reset does not work, you can flash custom recovery via Odin and follow the instructions in the thread below to restore stock 4.3. Afraid, you have to revert to full stock 4.3 to get the phone back in working order and don't even think about 4.1.1.
http://forum.xda-developers.com/showthread.php?t=2658486
If you are not able to get to recovery, then you can see if you can boot from a debrick image following the instructions (on the first page) of the thread below ...
http://forum.xda-developers.com/showthread.php?t=2549068
Once your phone is working normally, you can request the unlock code from AT&T via the request form below. If eligible, they should provide this. Otherwise, you would have to buy one online ....
https://www.att.com/deviceunlock/client/en_US/
Let me know if you need any further help.
KorGuy123 said:
Downgrading your boot loader from 4.3 is a guaranteed brick. I'm not sure if the brick will get you to the Samsung screen.
If you're already assuming its bricked reboot into recovery and do a full wipe. Restore a nandroid of something if you have one or try flashing a custom ROM. Because Odin failed maybe it never flashed the boot loader.
Worth a try
Sent from my SGH-I747M using XDA Free mobile app
Click to expand...
Click to collapse
I tried wiping everything, i also wiped cache, still didn't boot, thanks though!
Larry2999 said:
Welcome to the forum! Wished you'd come in much earlier though as you would have found you CANNOT downgrade from 4.3 to 4.1.1 to free unlock. Sorry, but once you are on 4.3, the surest way to unlock is to obtain the unlock code from the carrier or purchase one online. Sounds like you do have a soft brick. If your phone is still booting to the Samsung logo, then it's only a soft brick. Attempting to downgrade the 4.3 bootloader usually results in a hard brick so you may be in luck.
To fix this first, try to see if you can boot to recovery mode and do a hard wipe/factory reset. If you are able to boot to recovery (or download) mode then you have little to worry about. If the reset does not work, you can flash custom recovery via Odin and follow the instructions in the thread below to restore stock 4.3. Afraid, you have to revert to full stock 4.3 to get the phone back in working order and don't even think about 4.1.1.
http://forum.xda-developers.com/showthread.php?t=2658486
If you are not able to get to recovery, then you can see if you can boot from a debrick image following the instructions (on the first page) of the thread below ...
http://forum.xda-developers.com/showthread.php?t=2549068
Once your phone is working normally, you can request the unlock code from AT&T via the request form below. If eligible, they should provide this. Otherwise, you would have to buy one online ....
https://www.att.com/deviceunlock/client/en_US/
Let me know if you need any further help.
Click to expand...
Click to collapse
I am able to get to recovery, but the first link isn't very clear.... i am not really familiar with odin and all this other stuff... lol, i am now downloading the files it says to download in the first link though, can you maybe tell me in a quick list what exactly im supposed to do?
thanks!
baruchadi said:
I tried wiping everything, i also wiped cache, still didn't boot, thanks though!
I am able to get to recovery, but the first link isn't very clear.... i am not really familiar with odin and all this other stuff... lol, i am now downloading the files it says to download in the first link though, can you maybe tell me in a quick list what exactly im supposed to do?
thanks!
Click to expand...
Click to collapse
It's time to start reading. Before doing any flashing/modding, you should make sure you understand what you're doing and know the risks.
Now as for Odin, it's quite straight forward. Phone needs to be in download mode, you put the PDA file in Odin and flash (if it's a Odin one-click, just need to hit start). One thing is to not interrupt it! Especially if flashing bootloaders cause that will brick your phone. Also, don't downgrade bootloaders.
There are a few guides in the sticky, I suggest you take an hour or two reading them so things like that don't happen again (or that you know what to do if it does).
GL!
baruchadi said:
I tried wiping everything, i also wiped cache, still didn't boot, thanks though!
I am able to get to recovery, but the first link isn't very clear.... i am not really familiar with odin and all this other stuff... lol, i am now downloading the files it says to download in the first link though, can you maybe tell me in a quick list what exactly im supposed to do?
thanks!
Click to expand...
Click to collapse
Alright. If wipe/reset didn't work, you'll need to restore full stock 4.3 via custom recovery. Here's what we need to do....
1) Download the Odin flashable *.Tar file for custom recovery. I prefer TWRP because of the GUI so that's where I'm pointing you to ...
http://techerrata.com/file/twrp2/d2att/openrecovery-twrp-2.6.3.1-d2att.tar
2) Download the stock restore file for 4.3 from the thread below... If you are using TWRP, then the first link is the one you need
http://forum.xda-developers.com/showthread.php?t=2658486
3) Copy the stock restore zip file to a good quality (micro) SD card
4) I presume you have Odin already so you will use this to flash custom recovery to your phone. Run Odin.exe on your PC. If you are using Odin v.3.09 then you need the AP tab. For all other versions, use the PDA tab. Navigate to the custom recovery *.Tar file you downloaded earlier and place this in the PDA (or AP tab). Leave the default settings as is and do not check/uncheck any boxes other than the default settings.
5) Boot the phone to download mode via the 3-button combo (Volume Down/Home/Power). When you get to Odin (Download) mode, press volume up to continue. Connect the phone to your PC with a good quality micro USB cable. Wait until Odin has recognized the device then click on the Start button to start firmware installation (flashing). Wait for the flashing to end and the <Pass> message. Disconnect the phone from the PC and pull the battery to stop auto reboot.
6) Place the micro SD card with the stock restore zip in your phone. Replace the battery and boot to recovery mode. If you were successful with the firmware flashing above, it should boot you to custom recovery.
7) Select install from external card and navigate to the stock restore zip file. Select this file and swipe the screen to start firmware installation. Wait for installation to complete. Then clear your cache/dalvik and reboot to system.
This will hopefully do it.
I've tried searching and there doesn't seem to be a solution to this problem for this device.
Yesterday I was flashing ROMs, namely AICP, but I accidentally pressed Reboot to Bootloader in CWM. I got stuck in bootloop after that and it kept returning to recovery. I google'd for a solution and found this(androidforums-.-com-/esteem-all-things-root/478814-how-get-out-clockworkmod-recovery-bootloop.html), which I downloaded and foolishly flashed (devices unsimilar). Flash is successful, and I reboot my phone.
It now will not show the LG splash screen, nor will it enter Download Mode. When connecting the device via USB, it does not seem to add a COM port on the computer. What it does do is try to install a driver named QHSUSB_DLOAD which fails to install.
Could someone please help me solve this problem? Thanks..
dylanraga said:
I've tried searching and there doesn't seem to be a solution to this problem for this device.
Yesterday I was flashing ROMs, namely AICP, but I accidentally pressed Reboot to Bootloader in CWM. I got stuck in bootloop after that and it kept returning to recovery. I google'd for a solution and found this(androidforums-.-com-/esteem-all-things-root/478814-how-get-out-clockworkmod-recovery-bootloop.html), which I downloaded and foolishly flashed (devices unsimilar). Flash is successful, and I reboot my phone.
It now will not show the LG splash screen, nor will it enter Download Mode. When connecting the device via USB, it does not seem to add a COM port on the computer. What it does do is try to install a driver named QHSUSB_DLOAD which fails to install.
Could someone please help me solve this problem? Thanks..
Click to expand...
Click to collapse
Hate to say two things to you bro:
1) You didn't search very hard, because there was a related thread on page 3 with "QHSUSB_DLOAD" in the title
http://forum.xda-developers.com/showthread.php?t=2781522
I forgive though, but just letting you know.
2) You're screwed. The phone is hard bricked. No way to get it back to life.
How do I know? Well, look who's the creator of the thread just linked to.
Read the entire thread. It's not very long.
PS: PM me if your phone is still under warranty and you want advice on how to get it replaced. If you still aren't under warranty, then you're doubly screwed.
Hello and sorry if this is the wrong category...
It's my first time making a thread on xda.
I've been looking for an answer for the past 2 hours, but I still have a bricked phone... As the title says, I can't enter the recovery mode anymore. I tried to do a factory reset (when I could enter the recovery mode) and the phone got stuck at erasing. Now I can't enter the recovery mode anymore. I downloaded a new firmware from sammobile for the SM-G925F. The firmware works since I used it on an other phone and everything worked just fine. The problem is, when I open Odin and add the .tar file to AP, it gets stuck at nand write and sometimes on boot.img. The phone isn't showing that it's downloading anything (it has no progress bar). At this point I have no idea what to do...
Some extra info that could be helpful:
The phone was bootlooping when I got to fix it;
I work in a kind of phone repair store where customers bring their phones for hardware and software repair. I do the software;
I've installed new firmwares on multiple phones and I never had something like this... Normally some time with google and xda could help me to find a working way to fix the problem, but as I said... I've been looking for 2 hours and the problem is still here;
I'm not a pro with Android and phones. I just like to learn new things and I'm still learning.
Could it be a hardware problem?
Can you show me your phone's download mode image to see where could be the problem?
Also, make sure you are flashing latest firmware, if you are downgrading it - than you will get such boot errors.
*Update*
I found out what was wrong. The eMMC chip was broken.