Develop Bugs

phone showing up as N7100

I flashed the N7100 rom onto this to test it and couldn't get SIM/etc. Had to restore using stock firmware from ATT using ODIN. But, now, when I plug it back into the PC -- it shows up as a N7100 device and KIES won't support/recognize it.
Anyone know what I may need to reflash to get it to show the proper hardware id?
The ABOUT DEVICE section
MODEL: samsung-sgh-i317
Android: 4.1.1
Baseband: i317UCALI6
Kernel (perseus <-- this was custom add afterwards)
BUILD: JRO03C.i317UCALJ2

why do people keep doing this?

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Headunit 9" AC8227l YT9217B v1.61 Bootloop Help

Hi, I have this unit in BootLoop
Ram: 1Gb
Rom: 16Gb
AUTOCHIP AC8227l
Model: YT9217B v1.61 16G
Amp: TDA7388
CPU: MT6323LGA
WIFi: MT6625LN
Mem Chip: Rayson RSE16TAA-16
Other chip: RS 192M32LD
Resolution: 1024x600 9"Inch
MCU1: HW8227L-3.3-SW0-1.9
I uploaded a boot image to BMP and now it goes to BOOT LOOP. I downloaded it already tested with SP Flasher and various scatters, I installed the MTK drivers but the problem is that the PC does not detect the unit. I read about the TESTPOIN but I didn't understand what they are because on the forum and all unclear for me
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
P.s I have already seen in the old posts already on the forum
THX

Help with firmware update older HU

Hey so I have an older headunit from 2014. Looking to update the firmware to a newer one and was wondering if anyone could help me figure out which one is possible to use? Kind of confused with the MCU and which rom would be possible...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

I think the rk30sdk indicates that its a rk3066 unit. Its an Cortex-A9 Dual Core. Maybe this could help:
[ROM][RK3066/RK3188][SD/HD] Malaysk ROMs Android 4.4.4 for any yet known MTCB-Device
FOR RK3066 How to get to reсovery if you touch buttons - http://forum.xda-developers.com/showpost.php?p=65891188&postcount=2225 Special message for beginners now !! Before experimenting with firmware, Check to make first of all that you can to...
forum.xda-developers.com
I think there is nothing newer than Android 4.4. But i don't know how you could upgrade.

[HELP!!!] Battery drains too fast

ROM version: lineage-17.1-20210114-nightly-sagit-signed
Recovery version: lineage-17.1-20210114-recovery-sagit
Firmware version: 20.6.18
I flash the latest Lineage OS 17.1 on my Mi 6.
I have not installed any third-party software, or even flashed OpenGapps.
I have tried to completely erase all partition data and re-flash Lineage OS.
But the battery drops quickly.
Then i found the log.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
What is "53:qcom,glink-smem-native-xprt-rpm:93:7781b8.qcom,mpm"?
I uploaded my Bugreport.
Can somebody help me ....

you can try to connect a usb drive vie OTG cable, if the phone can go to deep sleep then your type c port is having trouble.

Question Android Version Mismatch With Kernel Version

I reflashed my S22 recently, but realized that the Android Version (13) does not match with Kernel Version (Android 12-9).
My S22 is Snapdragon variant, from Singapore. (not sure if it because I flashed incorrect firmware)
Mainly is because I encounter that Samsung Pay Transit card no longer work while screen is off.
Could this be an issue, and is it recommended that I reflash the latest firmware again?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

The kernel version should not affect any functionality.
The S22 uses android common kernels(GKI) which is why it seems wrong/out-of-date.
Per the Android OS developer website, android12-5.10 is a supported kernel for use with Android 13.
https://source.android.com/docs/core/architecture/kernel/android-common#compatibility-matrix