phone on bootloop. i forgot to make back up. i tried flashing on smartswitch or odin. i use cof6 firmware. how would i know if usb debugging is enabled if theres no os???
the download mode says this
current binary: custom
system status: custom
frp lock: off
secure download: enabled
knox warranty void: 1 (0x0304)
ap swrev: b:3 k:2 s:2
any help is appreciated
It looks like you should have been able to use either odin or smart switch. what happened when you tried them?
Related
Hi All,
I tried to root my device 6 months before and done that. i have not installed any custom ROM but installed Xposed installer.
Now i want to unroot and back to official for software updates.
i have tried Super SU for unrooting wand Triangle away to reset reset counter. Now i dont have rooting access but still my device shows as custom. Can someone please help me how bring my device status back to official. i have listed my device status below for your reference.
Odin Mode Information:
Product Name : GT:N7105
Custom Binary Download : Yes (1 Counts)
Current Binary : Custom
System Status: Custom
Knox Warranty Void : 1
RP SWREV: A2
Device Version:
AP : N7105XXUEMK9
CP : N7105BVUEMK1
CSC : N7105FTMEML1
Purchased my mobile in Singapore, not sure about the carrier but it shows Orange when i reboot my device.
Thanks for your time.
i was running 6.0.1 i was trying to downgrade to 4.4.4 but i messed and put the csc where the ap was supposed to go. so i did it the way i was supposed still a fail. i need a file that will work and root to if its possible. i know sm-n910a is a difficult model. i would have downloaded from sammobile but they dont have any stock firmware for this model. every time ive rooted or changed firmware on my other galaxy devices ive used ap/pda that's what threw me off. after that i tried flashing back to 6.0.1 stock. now im in a boot loop.
odin mode (high speed)
product name:SM-N910A
current binary: Samsung official
system status: official
reactivation lock: off
knox warranty void: 0x0
qualcomm secureboot: enable (csb)
rp swrev: s1 t2 r1 a2 p1
secure download : enable
udc start
江信江疑 said:
i was running 6.0.1 i was trying to downgrade to 4.4.4 but i messed and put the csc where the ap was supposed to go. so i did it the way i was supposed still a fail. i need a file that will work and root to if its possible. i know sm-n910a is a difficult model. i would have downloaded from sammobile but they dont have any stock firmware for this model. every time ive rooted or changed firmware on my other galaxy devices ive used ap/pda that's what threw me off. after that i tried flashing back to 6.0.1 stock. now im in a boot loop.
odin mode (high speed)
product name:SM-N910A
current binary: Samsung official
system status: official
reactivation lock: off
knox warranty void: 0x0
qualcomm secureboot: enable (csb)
rp swrev: s1 t2 r1 a2 p1
secure download : enable
udc start
Click to expand...
Click to collapse
So, what happens if you try putting it back to Download Mode and reflashing the 6.0.1 correctly this time?
Hello
i am melvirus
This is my first comment here, I apologize if this is out of place, come to this forum looking for a solution to a problem presented on my phone.
It turns out that my phone does not allow me to install any roms, it has been proven with several and none let me perform the complete procedure.
I always get the same error, nand write start fail.
On the phone the following appears in the download mode
odin mode
product name: GT-I9192
Current Binary: Custom
System Status: Official
Knox Kernel Lock: 0x0
Knox Warrante void: 0x1
csb-config-lsb: 0x30
In gray letters
bootloader ap swrev: 2
write protection: enable
Someone could help me a little
hello forum friends I come with this little problem which is that when I flash this phone takes the flash well but I stuck the samsung s4 mini i9192 duos and above I get some blue letters that says recovery booting. I can enter in the recovery mode and I realized that when I put it in download mode it comes out at the end with some letters that says write protection: enable and half lei that say that because it is enabled, it does not let the system flash to the cell phone.
because the help I need is how to disable that option or some other medium where I can install the software.
PD: I do not know what version the cell phone had since it was brought to me because it was frozen and flashed with several flash and always gives me that problem taking into account that the flash that I put on are good because they are the ones I use with other phones of this same model. it's the first one that comes up with that option
thanks for your help
ODIN NAME
PRODUCT NAME: GT-I9192
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICIAL
knox kernel lock: 0x30
knox warranty void: 0x1
CSB-CONFIG-LSB: 0X30
bootloader ap swrev: 1
write protection: enable
someone to help me with this problem I do not know what else to do thanks
Sorry for my language is the google translator
hi, i received an old galaxy s4 mini i9195i still with kitkat 4.4.4;
i tried to update android with a new version but it says "the lateset update have already been installed"...
so i tried to unlock to install a custom recovery/rom etc but the first problem is that ther's no unlock option in developer options...
i tried to uninstall knox but many tips i read always say that you have to open knox app/setup/device admin/and unchek somthing
but on my phone ther's no knox icon... the only knox stuff i found is in /phone setting/app mgr/all/ and i find only related running services (klms agent, knox, knox notif mgr, knox setup wizard client (which have all the turn off buttons grayed and you can do nothing else)
in fastboot:
Odin mode
product name: GT-i9195i
current binary: samsung official
system status: official
reactiovation lock (KK): OFF
knox warranty: 0x0
Qualcomm secureboot: enable (CSB)
rp swrev: s1, t1, h1, r1, a1, p1
secure download: enable
*#1234# current firmware
AP: I9195IXXS1AQA2
CP: I9195IXXU1A0D1
CSC: I9195IVFR1A0D1
knox: 2.2
any suggestion from where can i begin (with the first goal of not hard bricking the phone )?