Hi all,
My XDA IIs works well before. But few days ago the Power button doesnt work properly, it can turn on the phone, hold to turn off the back light, but I can't use it to turn my phone screen off like before. Anyone has same problem ?
Can you see any part of the screen? It might just be that the backlight adjustments are set too low when the unit isn't cradled. You might be able to see the screen in daylight.. or maybe it was inside your home. I forgot where I was at when it happened to me. In anycase, if you can see a bit of images on your screen, go into the Backlight properties and change the setting to your liking.
Good luck..
The problem is i can just press the power button to turn off my phone BEFORE (the screen is completly off), and NOW it doesnt work at all ! When my phone was off, I can press the Power button to turn it on, or when I hold it for few seconds the back light will be turned off, but press once to turn off. I dont know why, if somthing wrong with the Power button it should be doesnt work at all, that's mean i cannot turn on my phone as well. But other functions of the Power button are still work well, except the 'Turn off' :roll:
power off doesn't work anymore
I have the same problem here. I can't use the power button to power off my qtek 9090!!
i can use the power button to turn my pda on and to switch the background light on and off - so the "hardware side" of the power button is working.
however, i can't use the power button to turn off the device. it's very annoying, because i can't put it in my pocket after finishing a call :-(
this should be some sort of a software problem - so i hard resetted my device (a couple of times) - but that didn't help!
can anyone help?
thanks,
lorenz
the ba doesn't turn off it is always on staand by mode. ->settings -> system -> button lock
this will stop any missed call because when the ba is in standby the power button is the only one to work
power on is no problem. i can't put my BA into standby mode. if i press the power button while the BA is turned on, nothing will happen. the screen will stay on, the background light stays on.
i have no way to put it into stand-by with the power button!
try this and see if it works. it's a software app that wil rest, shut down, and turn the screen off. just copy it to your BA temp directory and install it.
power button problem
nemchua
Is your problem solved ?
Because I have the same problem.
Power of switch doesn't work !!!
Any help would be welcome.
power button problem
Does anyone solve the problem???
Had the same problem...
I had the same problem going on for about two weeks or so...never changed anything and it went away all by itself.
The problem has not come back now in over 4 months.
Sure would love to know what the problem was tho...
Greetings,
Noddy
Power Off does not work
Add my name to people with this problem.
The only event I can link it to is this: I deleted my Motorola Bluetooth headset and installed a Logitech headset. I noticed the problem (can't turn OFF with POWER BUTTON) soon after that.
same problem for me ..... someone must know !!!!
I think it is a hardware problem. The contact is not making cleanly. Disassemble and spray time, perhaps.
It's a standard push switch, easy enough to replace, I occasionally list themon ebay but any phone repairier should have them in stock.
Richard
i had same problem yesterday afternoon, but it is ok now. recovered by himself
Write again in two weeks and let us know if it is still healthy. In my case, anintermittent problem became continuous.
Can't turn the screen on after pressing power button
I have a problem with my Bell Atrix. After pressing power button to lock the screen, i can't wake up the screen up by pressing that button again. Could anyone tell me how to fix it pls.
So I have my htc one x for a year now. Rooted and custom rom, all worked fine.
The keypresses of the power button will be simulated very fast with no actual pressure on the power button. So after some minutes off locking and waking my device I pressed volume down and power button. Now sometimes it simulates the volume down and power button.
So sometimes it shuts off the device.
So I opened the device and there appears to be nothing wrong with it. I turned my HOX on and quickly unplug the ribbon cable from the power button off. But the power button is still pressed really fast, like 2 times a second.
I can't even go into recovery to backup, restore or flash anything because it will press the power button really quick and after 10 seconds it turns itself off.
It happened before on Slimbean rom. But the problem went away after some days. Now i got MIUI and the problem is back. So I don't think it is rom related.
My solution:
Is there a way to disable hardware keys in the recovery? Then i can try to restore my official RUU nand..?
Long story short, 1 month ago my Nexus 7 (2013) got water damaged, I immediately covered it in rice and left it for a couple of days, and after turning it back on, have a weird issue.
The power button will not work what so ever, I've tried holding it in for over 60 seconds, aswell as holding in the volume buttons along with the power button.
The only way to turn it on is to plug the nexus into the mains. I then get the white LED flashing 5 times, which I assume means it's charging up from a completely dead battery.
After about 20 minutes of charging, the google logo will pop up, stay on for 3-5 seconds, then the unit will reset itself (screen goes off, then back on to the google logo, and repeats like that).
However....If i hold in the volume down button, it'll boot up like normal, everything works fine, but take your finger off the volume button and it'll reset and only boot to the google logo. Holding volume up will take it too the boot loader.
The issue is that at no point, (in the bootloader or once its booted in to the OS) will the power button work whatsoever.
I first assumed that the button was broken, and stuck to the ON position, so ordered a new button cable (which includes the power button, volume up and down, aswell as the microphone) but this hasn't done anything.
Wondering if anyone had any thoughts?
Hi,
I have a SM-320 running CM13. I have had this problem in two different nightly builds so far. I had the problem when on 12/30 build and now on 02/08 build. I have moved to CM13 since mid December. Did not have this issue on stock ROM.
Wanted to know if this is a Hardware issue or ROM Issue.
What happened:
The Tab was connected for charging overnight. When I try waking it with home button press or power button press, no response. The display is dark, the back and task key lights dont light up. Its looks like the Tab is powered down. When I Press the power button to start, it doesnt work.
I connect it back to power and keep it charging for some time and then try the home+vol up+power press for 1-2 mins, the tab powers up to TWRP. Now I can boot back to system. When I check the battery, its 90%+ charged.
I want to know if this is a symptom of hardware failure or something to do with the ROM. I am in India and the service center here dont service this model.
Cheers
hi guys,
I recently did something slightly different on my T700 that I've owned for almost 3 yrs now.... I enabled the finger print reader. After that, I noticed some odd behavior over the next few days, but nothing too out of the ordinary.
Anyway a few days later, the touchscreen stopped working. I have a feeling that enabling the fingerprint reader, had something to do with this. The home button works, so does the power and vol +/-. But swiping my fingerprint over the home button does not spark any response, and I cannot enter my backup password at all.
1) I have tried powering off using the power button - this does not work. The power menu appears on the touchscreen and I cannot select it.
2) I've tried holding down the power button for 10+ seconds - this does nothing, which seems odd. Normally this will restart any device after a few seconds.
3) I've tried "power + vol up + vol -" all simultaneously. This forces the device to restart, but the problem is still present.
4) Tried running the battery down, then charging up and turning on... but it's the same outcome as (3).
5) tried wipe data/wipe cache/factory reset... it has gone back to the start-up screen, in Korean.... but the touchscreen still does not work!!!
Please... help me..!!!! lol
Bueller...Bueller.... Anyone...