Driver LGE Android MTP Device - G4 Q&A, Help & Troubleshooting

This thread is about the defective installation of the LGE Android mtp device driver. Note that when the phone is on all the drivers seem to work correctly (LGE mobile ADB interface under "android device", G4 driver under "portable devices" and LGE mobile USB serial port).
The issue presents when i switch the phone to "download mode"; in this mode the "G4" driver (which is the LGE Android MTP device) appears not to be working.
The problem persists on three different PCs, either with windows 10 or windows 7 and either with a LG G4 or an LG G3.
I would like to root my G4 device following the firmware flash procedure 10E, but I am not sure that I can flash the device if there is this kind of issue with the drivers. Is it normal that the device appears not to be working?

I am having the same problem as you were. I am using Windows 7 and several versions of the LG drivers with the same result; Everything is fine when my device (a G4) is booted normally but in Download mode I get the same error as you (This device cannot start. (Code 10)).
I have tried everything I can think of, I have uninstalled all the old Android drivers with USBDeview, disconnected the internet to stop windows update installing its own drivers, different USB ports and cables.
Did you ever get your device rooted?

SO... in my case (YMMV - be careful) it turns out there is no need for the device manager to be error free when the phone is in download mode.
I just got root using this procedure from the "Root ANY LG G4 Variant 100% Success Directives | Root Injection | Less Bricks" thread with no issue. I thought it would work because the LGMobileSupportTool was reporting as being connected to my phone despite the error (This device cannot start. (Code 10)) in device manager. Sure enough everything worked fine. I wish it hadn't taken me (literally) 20 hours of fecking around with drivers to get to this point though...
ETA I have a G4 H815 (EU)

i had a problem too. my device is rooted and i cant access mtp after... what might be the problem?

012512 said:
i had a problem too. my device is rooted and i cant access mtp after... what might be the problem?
Click to expand...
Click to collapse
Edit. Performed a factory reset and it worked as it is.

I had this problem too. It turns out that problem was in Xposed module "Xposed Media Scanner Optimizer". If this module is loaded up, I can't connect via MTP with same error Code 10 in Device manager. So, if you have Xposed, try to uncheck all modules and restart.

PDAlama said:
I had this problem too. It turns out that problem was in Xposed module "Xposed Media Scanner Optimizer". If this module is loaded up, I can't connect via MTP with same error Code 10 in Device manager. So, if you have Xposed, try to uncheck all modules and restart.
Click to expand...
Click to collapse
But in my case only greenify is installed module,
Why you only post that After I factory reset my phone. Haha anyway thanks for the information.

PDAlama said:
I had this problem too. It turns out that problem was in Xposed module "Xposed Media Scanner Optimizer". If this module is loaded up, I can't connect via MTP with same error Code 10 in Device manager. So, if you have Xposed, try to uncheck all modules and restart.
Click to expand...
Click to collapse
This helped me so much when I was trying to upgrade to Android M. After un-checking all my xposed modules, both my pc and laptop were finally able to read my LG G4 and install drivers, mtp, and others correctly without fail.

Same problem here with an AT&T G4. I've tried 2 different Win7 laptops (one of which has never had any Android drivers/tools installed previously), 3 cables, and even performed a factory reset. MTP Drivers work when booted normally, but fail ("Code 10") when in download mode. Any additional suggestions?
EDIT: As suggested by other posts/forums, this issue can be ignored, and isn't an actual problem. ADB works successfully, even if the MTP device isn't working in Windows' Device Manager. (This MTP device appears in Windows' Device Manager the same as it does when a USB Debugging connection hasn't (yet) been authorized on the Android side. My guess is that since Android isn't fully booted while in Download Mode, there's nothing to approve the connection. Either way, it doesn't affect the function of Download Mode, as long as the other Android-related devices in Device Manager have their drivers loaded successfully.)
TL;DR version: When in "Download Mode", as long as the other Android-related device(s) in Windows' Device Manager are working, ignore the "Code 10" error / "yellow triangle" on the MTP device. It's not needed for Download Mode to work.

Related

"Hardware ID doesn't match" error when plugging phone in

Okay, this is the second time this error has popped up and it's starting to get on my nerves. Anytime I plug my phone into ANY USB port, and this is counting both 2.0 and 3.0 ports, I get the error bubble: Hardware ID Missing. Windows cannot identify the device plugged into the SAMSUNG Mobile USB Composite Device." Honestly, this is beyond irritating.
For one, I am not going to reinstall Windows 7. That's too much hassle for this. Second, ever since someone plugged their Droid into my USB cable so they could charge up their phone, this message started appearing. I tried to reinstall drivers (Samsung driver exe said it couldn't install), uninstall, disable, etc etc, but finally managed to get the damn computer to read it when I stuck it in the 3.0 USB port. Now, just 10 minutes ago, I plug the phone in, I get that error, on a 3.0 USB port.
So, now I have no idea what is going on, nor how to fix it. I've tried searching, but there are no answers. Or, the possible "solutions" don't even work even remotely close.
I could really use some help on this. And, again, please do not mention "Reinstall Windows". That's just too much of a hassle and I'm not going to do that.
You may not want to try this either but try a system restore
Sent from my SPH-L710...if some one helps you press the thanks button
Volknochi said:
Okay, this is the second time this error has popped up and it's starting to get on my nerves. Anytime I plug my phone into ANY USB port, and this is counting both 2.0 and 3.0 ports, I get the error bubble: Hardware ID Missing. Windows cannot identify the device plugged into the SAMSUNG Mobile USB Composite Device." Honestly, this is beyond irritating.
For one, I am not going to reinstall Windows 7. That's too much hassle for this. Second, ever since someone plugged their Droid into my USB cable so they could charge up their phone, this message started appearing. I tried to reinstall drivers (Samsung driver exe said it couldn't install), uninstall, disable, etc etc, but finally managed to get the damn computer to read it when I stuck it in the 3.0 USB port. Now, just 10 minutes ago, I plug the phone in, I get that error, on a 3.0 USB port.
So, now I have no idea what is going on, nor how to fix it. I've tried searching, but there are no answers. Or, the possible "solutions" don't even work even remotely close.
I could really use some help on this. And, again, please do not mention "Reinstall Windows". That's just too much of a hassle and I'm not going to do that.
Click to expand...
Click to collapse
I had the same issue what ended up fixing it for me was watching when I plugged the phone in after a clean driver install and stopping Windows from downloading and installing an updated driver. Dont know if its the same for you but that fixed it for me. I was really frustrated by it and found no help either.
probably an easy fix
definitely don't need to reinstall windows or do a restore. But just to be sure, you don't have kies installed right? Seems to cause problems.if there's no kies installed, go into the device manager and find your phone whatever it's listed as right click and uninstall. Check the little box that says, "delete the driver software for this device". do this for any devices relating to yours. Including the stuff under modems,ports,USB controllers.and tick that box that delete driver software for this device every time you uninstall something. Now, not saying it's necessary but wouldnt hurt, reboot the pc. Then with your phone unplugged, reinstall the Samsung drivers for the phone. Now to make sure windows doesn't DL its own drivers,disconnect from the internet and plug the phone back in. Should be all good.
I won't do a system restore, that won't do anything. Not to mention it would erase some programs that were installed (not related to phone). So, not doing that. Also, my computer will not automatically update any drivers or any thing else, as I have it set to manual mode.
And, I do not have Kies installed. It never worked for me properly, when it came to driver installation. I've done the "go into device manager" bit many times before, it still likes to play the "Hardware ID doesn't match" card. Drivers won't install either. I don't know what it is, but damn this is the most stubborn thing I've ever encountered.
i've post this in other forums today. what i do to get it working is i toggle USB debugging and try it out, then start toggling the ptp and mtp until it works. the combo that works for me is turn on debug, plug in computer, unplug, turn off debug, plug in. if it doesnt work then i toggle back and forth MTP and PTP. 5 tries at most, for me. Also, i did a nandroid back to my oem ICS that was 2 weeks old and just rooted. the problem is worse there. i'm using freegsmr6 with trinity kernel on Tmo. hope it helps.
Ditto
Yeah that whole "Hardware ID missing" was an irritating situation. This is what I recommend as far as making it work.
1. Plug in.
2. When you get the error message, I think its because of a conflict with the ADB interface. Go to Settings, Developer Options, and check off USB Debugging.
3. Plug in once again and it should work. If not, try toggling between Camera and MTP.
I have Windows 7 Ultimate and it works fine for me
I always get that error as well with my SGS 3. I have to reinstall Kies everytime it does that which is annoying.. ANyone has a permanent solution about this?
Fix for me was...
1-plug in phone. Get the hardware ID message. Leave phone plugged in.
2- open device manager. Click on. Android Phone and Uninstall Samsung Android ADB Interface. Also check the "delete software driver" when the dialog box shows.
3-still in device manager. Scroll down to Universal Serial Bus Controllers. Uninstall Samsung Mobile USB Composite Device.
4-unplug phone.
5-reboot pc.
6-install SAMSUNG USB drivers from their site or from here
http://www.epiccm.org/2012/06/cwm-recovery-on-all-sgs3-lte-variants.html?m=1
7-reboot or not. Plug in phone.
This worked for me and no issues for the last 6 days. YMMV..
this works!
stevounit said:
yeah that whole "hardware id missing" was an irritating situation. This is what i recommend as far as making it work.
1. Plug in.
2. When you get the error message, i think its because of a conflict with the adb interface. Go to settings, developer options, and check off usb debugging.
3. Plug in once again and it should work. If not, try toggling between camera and mtp.
I have windows 7 ultimate and it works fine for me :d
Click to expand...
Click to collapse
But why this problem now out of nowhere when everything worked fine before.
Sent from my SPH-L710 using xda app-developers app
Hardware ID missing - SOLVED!!
1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection.
I've done just that, I've connected my S3 to the PC several times, I've also rebooted twice and I've never seen that stupid message again - while of course everything works as expected.
:good::good:4 days later, several times rebooted (phone and PC), several connections with Kies and I have NEVER seen that error again - it works!!
UPDATE!! (Oct.11.2012)
After a few Kies updates and going through various ROM's:
- the procedure listed above works 100% but a few steps are just not needed (redundant) - see bellow
- the problem is mostly caused by Windows "forcefully" trying to install its own drivers, rather than allowing Samsung's suggested.
- Samsung's fault is providing "updated" drivers that don't always work (hence, use the suggested 1.4.6.0 drivers)
- Following EVERY Kies update, DISCONNECT from internet before plugging your phone (otherwise you'll have to go through this, AGAIN).
Some suggested here that plugging the phone into a different USB port (without disconnecting from internet) would be the culprit - which happens to be true, but as a mere effect, not the cause: every time an unknown device is plugged into a different USB port, Windows is trying to download/install the appropriate drivers if it doesn't recognize the hardware - and there you are again.
So, the simplified procedure becomes:
1. Not needed - leave Kies installed, as is - no harm at all
2. N/A
3. YES
4. Not (always) required
5. MUST
6. MUST
7. MUST
8. Yes
Furthermore, if still interested in connecting your I747(M) as UMS (USB mass storage) the solution presented here works. I tested it myself - read my comment on this post for the very few existing hiccups.
- while installing the USB mass storage device drivers you don't have to disconnect from the internet
Install Drivers
Have you tried just installing the drivers directly from Samsung? That is all I did when I had problems and it worked.
tyler1037 said:
Have you tried just installing the drivers directly from Samsung? That is all I did when I had problems and it worked.
Click to expand...
Click to collapse
For someone experiencing the "hardware ID missing" error, just reinstalling the drivers won't do anything. Like many others, I've been banging my head trying to solve this for quite some time; the suggested steps are truly a compilation of successful ideas and trials mingled with tons of frustration, coming from my own experience as well as from many different people and forums.
If, on the other hand, you had a different type of connectivity issues - without this error, then, yes, reinstalling the drivers is Samsung's recommendation.
billard412 said:
definitely don't need to reinstall windows or do a restore. But just to be sure, you don't have kies installed right? Seems to cause problems.if there's no kies installed, go into the device manager and find your phone whatever it's listed as right click and uninstall. Check the little box that says, "delete the driver software for this device". do this for any devices relating to yours. Including the stuff under modems,ports,USB controllers.and tick that box that delete driver software for this device every time you uninstall something. Now, not saying it's necessary but wouldnt hurt, reboot the pc. Then with your phone unplugged, reinstall the Samsung drivers for the phone. Now to make sure windows doesn't DL its own drivers,disconnect from the internet and plug the phone back in. Should be all good.
Click to expand...
Click to collapse
Just wanted to say thank you. Did this and the last 2 days, works everytime. I made sure that after the first time I plugged the phone in after doing all this, and the screen pops up asking what I wanted to do, made sure to check the box for "do this everytime" and then choose the view folder option or whatever that is.
Thank you again,
Whiteice
One thing I have tried which might help others - I had the Android Developers toolkit installed on my machine, which I've removed and I also removed the HTC Sync software which was for my old desire.
Rebooted, installed the SG Toolkit (can't remember which post I found it in) and then chose option one after selecting firmware to install drivers.
I cancelled the "Windows Updates" bit of the driver detection and it found the first item, and had "item disconnected" for the remaining three.
Unplugged and plugged back in and voila it works.
This worked for approx 5 mins and then stopped, however I did all the above with debugging on, debugging is now off and all seems well (touch wood). However looking at putting on a different kernal to expose storage as mass storage and also get around cifs issues.
Hope this helps someone.
nacos said:
1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection.
I've done just that, I've connected my S3 to the PC several times, I've also rebooted twice and I've never seen that stupid message again - while of course everything works as expected.
:good::good:4 days later, several times rebooted (phone and PC), several connections with Kies and I have NEVER seen that error again - it works!!
Click to expand...
Click to collapse
Thank you so much for this. This solution worked for me.
nacos said:
1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection.
I've done just that, I've connected my S3 to the PC several times, I've also rebooted twice and I've never seen that stupid message again - while of course everything works as expected.
:good::good:4 days later, several times rebooted (phone and PC), several connections with Kies and I have NEVER seen that error again - it works!!
Click to expand...
Click to collapse
Thanks for this i will try it tomorrow as still new to these tabs.
For moment i change to camera PTP and it pops up, so at least i can use it for now.
Will let you know how i get on.
Best wishes :good:
adamspud said:
One thing I have tried which might help others - I had the Android Developers toolkit installed on my machine, which I've removed and I also removed the HTC Sync software which was for my old desire.
Rebooted, installed the SG Toolkit (can't remember which post I found it in) and then chose option one after selecting firmware to install drivers.
I cancelled the "Windows Updates" bit of the driver detection and it found the first item, and had "item disconnected" for the remaining three.
Unplugged and plugged back in and voila it works.
This worked for approx 5 mins and then stopped, however I did all the above with debugging on, debugging is now off and all seems well (touch wood). However looking at putting on a different kernal to expose storage as mass storage and also get around cifs issues.
Hope this helps someone.
Click to expand...
Click to collapse
The Android Developers toolkit DOES install the USB drivers 1.4.6.0 - which seems to be the ONLY one that works, BUT the rest of the steps suggested in my previous post are needed in order to get rid of the problem - otherwise the fix is just temporary.
Re-loading OS drivers corrected issue.
tyler1037 said:
Have you tried just installing the drivers directly from Samsung? That is all I did when I had problems and it worked.
Click to expand...
Click to collapse
I removed the updates to Kies on my Note and uninstalled the Kies update on the PC which is what started this issue of the OS not recognizing the device and then a fresh driver load for my phone from the Samsung site. Worked Perfectly, Thanks!
Cowoholy

[Q] My 8.4 wifi can't connect to windows 7 pc

I have recently root my samsung tab pro 8.4 wifi version. Everything seems to work well, except USB connection to my windows7 desktop. I installed the latest version of Samsung usb driver (download from Samsung's web site for my device). Whenever I connect it, media device mode, the "installing device driver software" icon spins for couple of minutes, then I got the error of "Device driver software was not successfully installed" . In the detail dialog window, it says "MTP USB Device" failed with a red cross. what did I do wrong? thanks.
I have tried several different USB 2 ports on my computers. Also I have Developer mode turned on, with or w/o USB debugging checked. Nothing seems to work. Also the camera mode doesn't work either.
Did you install kies 3 from samsung?, this should install all the drivers you need.
http://www.samsung.com/us/kies/
I tried with this version of kies from samsung's website, not working. Got the same failed to install device driver message.
In windows device mananger, it shows a MTP USB device with yellow "!" mark on it. If I try to update driver from here with the driver installed on my computer, it says I have the latest driver installed already.
dealcrack said:
I tried with this version of kies from samsung's website, not working. Got the same failed to install device driver message.
In windows device mananger, it shows a MTP USB device with yellow "!" mark on it. If I try to update driver from here with the driver installed on my computer, it says I have the latest driver installed already.
Click to expand...
Click to collapse
Try going to Device Manager in Windows, find the device, pick the option to select from the drivers on the computer, then pick the "USB MTP drivers" (generic, not Samsung) and see if that helps.
redpoint73 said:
Try going to Device Manager in Windows, find the device, pick the option to select from the drivers on the computer, then pick the "USB MTP drivers" (generic, not Samsung) and see if that helps.
Click to expand...
Click to collapse
thanks for your help. I tried your suggestion, and
I went to the Device Manager, and select the "MTP USB Device" with yellow "!" mark, choose this menu,
Update driver software->Browse my computer for driver software->let me pick from a list of device drivers on my computer
I see two drivers, however either works for my 8.4 pad. It says "This device cannot start (code 10)"
Also when I open the properties for this device in device manager, it shows its driver running is from Microsoft, driver version 6.1.7600.16385. Should be a driver from Samsung?
dealcrack said:
thanks for your help. I tried your suggestion, and
I went to the Device Manager, and select the "MTP USB Device" with yellow "!" mark, choose this menu,
Update driver software->Browse my computer for driver software->let me pick from a list of device drivers on my computer
I see two drivers, however either works for my 8.4 pad. It says "This device cannot start (code 10)"
Also when I open the properties for this device in device manager, it shows its driver running is from Microsoft, driver version 6.1.7600.16385. Should be a driver from Samsung?
Click to expand...
Click to collapse
Are you running stock TouchWiz ROM? Just to be sure.
Otherwise you could remove all your USB drivers related to Android and start from scratch with just the Sammy driver. I had to do that for my previous OnePlus One, it just wouldn't connect. It chose a wrong driver each time I hooked it up so I had to just remove those from the driver store and then make it choose another one. That was for ADB thought, but I guess it couldn't hurt to try anyways.
The reason I'm mentioning if you're on stock ROM is because this morning, on CM nightly 01-24 I had some troubles with my tablet being read by Windows, it was fixed in 26 so.. Just wanted to mention it.
CuraeL said:
Are you running stock TouchWiz ROM? Just to be sure.
Otherwise you could remove all your USB drivers related to Android and start from scratch with just the Sammy driver. I had to do that for my previous OnePlus One, it just wouldn't connect. It chose a wrong driver each time I hooked it up so I had to just remove those from the driver store and then make it choose another one. That was for ADB thought, but I guess it couldn't hurt to try anyways.
The reason I'm mentioning if you're on stock ROM is because this morning, on CM nightly 01-24 I had some troubles with my tablet being read by Windows, it was fixed in 26 so.. Just wanted to mention it.
Click to expand...
Click to collapse
Yes, I am on the stock TouchWiz ROM, but I rooted it following steps from one thread in this forum. Before rooting, I was able to connect. I do have a LG G3 phone connecting to the same computer successfully. Will this cause any problem? Will going to CM ROM solve my problem?
Also, can you tell me steps to remove all my USB drivers related to Android in Windows 7?
dealcrack said:
Yes, I am on the stock TouchWiz ROM, but I rooted it following steps from one thread in this forum. Before rooting, I was able to connect. I do have a LG G3 phone connecting to the same computer successfully. Will this cause any problem? Will going to CM ROM solve my problem?
Also, can you tell me steps to remove all my USB drivers related to Android in Windows 7?
Click to expand...
Click to collapse
It may work to install CM11 or CM12, BUT try this toolfirst (uploaded to my personal box account) Find all your mobile device drivers in this list and mark them and go to "File" and click "Uninstall marked drivers", restart your PC and plug in your tablet. Then try plugging in LG after so it gets drivers later. I'm not sure if it will work. But it should apply new drivers. If it doesn't work, uninstall the drivers one more time and download the Samsung drivers from 3rd party and install them and apply then manually to your tablet through Device Manager in Windows.
https://app.box.com/s/7njztz17hekfkpxbjk7h79xsctnmuptn
Anyways, try this first.
dealcrack said:
I do have a LG G3 phone connecting to the same computer successfully. Will this cause any problem?
Click to expand...
Click to collapse
Its always a possibility. I'd try to uninstall the LG drivers. You can always re-install later (if needed).
In a perfect world, the Sammy drivers would be what you want. But this is of course not a perfect world. I've had better luck using the "generic" Microsoft MTP USB drivers over the HTC drivers on my HTC devices.
CuraeL said:
It may work to install CM11 or CM12, BUT try this toolfirst (uploaded to my personal box account) Find all your mobile device drivers in this list and mark them and go to "File" and click "Uninstall marked drivers", restart your PC and plug in your tablet. Then try plugging in LG after so it gets drivers later. I'm not sure if it will work. But it should apply new drivers. If it doesn't work, uninstall the drivers one more time and download the Samsung drivers from 3rd party and install them and apply then manually to your tablet through Device Manager in Windows.
https://app.box.com/s/7njztz17hekfkpxbjk7h79xsctnmuptn
Anyways, try this first.
Click to expand...
Click to collapse
I download this tool, and remove all Samsung or Android related USB driver. Restart my computer and connect the pad it's not working. Then I uninstall the Samsung driver software, and all USB driver. Then restart and install a samsung driver from the thread about how to root my pad in this forum. Connect my pad, no luck. Still the same problem. I am about to give up.
redpoint73 said:
Its always a possibility. I'd try to uninstall the LG drivers. You can always re-install later (if needed).
In a perfect world, the Sammy drivers would be what you want. But this is of course not a perfect world. I've had better luck using the "generic" Microsoft MTP USB drivers over the HTC drivers on my HTC devices.
Click to expand...
Click to collapse
I uninstall my LG driver too, along with all Samsung/Android usb driver with the tool from previous reply. No luck, It still shows a MTP device with yellow "!" mark.
Just before I about to give it up, it connects to my another computer now, which is my main computer and it had trouble connecting to. All I did was restart my pad several time and odin twrp recovery to it. It connects after rebooting. No idea what cause this problem, but it works now. thank you for all your help.
dealcrack said:
Just before I about to give it up, it connects to my another computer now, which is my main computer and it had trouble connecting to. All I did was restart my pad several time and odin twrp recovery to it. It connects after rebooting. No idea what cause this problem, but it works now. thank you for all your help.
Click to expand...
Click to collapse
Glad you sorted it out, to some degree or other.
USB connectivity on Android devices is very tricky, at least on Windows (can't speak on other OSes). My HTC phone connects fine to my work laptop with the HTC drivers. On my home computer (also Win7) it frequently drops adb connection and I have to manually select the "generic" Microsoft drivers to make it work (and the HTC drivers never seemed to work completely right either). My Sammy Pro 8.4 seems to connect just fine to my home PC, however. So it seems its just a crap shoot what kind of connectivity you will get, really.

*Solved* LG G3 No longer connects to PC via MTP/PTP - Only Charge-only

Hi Guys,
A weird one here for you, I'm already contemplating throwing my phone at a wall that's how long I've been trying to fix it.
I have a LG G3 D855 Gold 32gb model purchased via Kogan in Australia.
The unit is now on Android 5.0 (no updates available for 5.1+) - Software Version V20i-SEA-XX with Build number LRX21R.A1440645925.
This phone is non-rooted with stock ROM etc.
So the issue at hand, I upgraded my Win7 PC via the upgrade option to Win10 to retain my games/files etc.
Now when connecting the phone to the PC it only goes to charging mode and I am unable to click on it within the drop-down to change it to anything else.
I have tried LG G3 drivers, Googles generic drivers, ADB suite drivers. I am unable to adb find the phone, I do not have an Acer Composite device in Device Manager.
Win 10 keeps saying the device is not recognised/malfunctioned.
Tried different cords, double checked the connector on the phone for any dust specs etc.
My PC refuses to work with any driver I have thrown at it, however in each scenario with various drivers, warnings still persist in Device Manager.
Some of the drivers force the phone to connect/reconnect and cause the "ping" sound each time it disconnects and reconnects (with malfunction warning prompts).
This is on Win10 with 64bit Home edition.
I am at my wits end and can't think of anything I haven't tried beyond a factory reset of my phone (hoping not to at this stage as I'm thinking it's driver-related).
It won't let me tether or anything via USB also, same goes with USB debugging, no change.
Lastly which may also help narrow it down, with the phone plugged in BEFORE it gets to the OS, I can change between PTP/MTP and USB charge, however once the Win10 OS loads up, it disconnects/malfunctions and lists Charge Only.
And yes, this phone can connect on my Win7 small PC which I use for testing crap out on.
Any ideas guys?
Let me know if any log files or anything is required.
At this stage I am unable to do a root to the phone (due to adb issues etc) nor can I connect to the internal phone system unless I use in the in-built file explorer.
Edit: *SOLVED*
Ok so turns out the issue is, and this is just my case, my motherboard has various utilities, one of which is a USB 3.0 boost option.
When I did an upgrade to Windows 10, it somehow screwed up various programs on my PC including registry etc.
I reinstalled the particular utility (I was actually trying to fix my graphics clock etc so happy coincidence) which also re-installs the USB 3.0 Boost software which in turn has fixed my USB Ports.
So if you have a custom built PC (my Motherboard being a Rampage 4 Formula). Check the Mobo Utilities/Drivers for any conflicts.
I have the exact same problem, and I can't seem to find a solution for months now. It's really annoying and depressing
nicholsonr said:
Hi Guys,
A weird one here for you, I'm already contemplating throwing my phone at a wall that's how long I've been trying to fix it.
I have a LG G3 D855 Gold 32gb model purchased via Kogan in Australia.
The unit is now on Android 5.0 (no updates available for 5.1+) - Software Version V20i-SEA-XX with Build number LRX21R.A1440645925.
This phone is non-rooted with stock ROM etc.
So the issue at hand, I upgraded my Win7 PC via the upgrade option to Win10 to retain my games/files etc.
Now when connecting the phone to the PC it only goes to charging mode and I am unable to click on it within the drop-down to change it to anything else.
I have tried LG G3 drivers, Googles generic drivers, ADB suite drivers. I am unable to adb find the phone, I do not have an Acer Composite device in Device Manager.
Win 10 keeps saying the device is not recognised/malfunctioned.
Tried different cords, double checked the connector on the phone for any dust specs etc.
My PC refuses to work with any driver I have thrown at it, however in each scenario with various drivers, warnings still persist in Device Manager.
Some of the drivers force the phone to connect/reconnect and cause the "ping" sound each time it disconnects and reconnects (with malfunction warning prompts).
This is on Win10 with 64bit Home edition.
I am at my wits end and can't think of anything I haven't tried beyond a factory reset of my phone (hoping not to at this stage as I'm thinking it's driver-related).
It won't let me tether or anything via USB also, same goes with USB debugging, no change.
Lastly which may also help narrow it down, with the phone plugged in BEFORE it gets to the OS, I can change between PTP/MTP and USB charge, however once the Win10 OS loads up, it disconnects/malfunctions and lists Charge Only.
And yes, this phone can connect on my Win7 small PC which I use for testing crap out on.
Any ideas guys?
Let me know if any log files or anything is required.
At this stage I am unable to do a root to the phone (due to adb issues etc) nor can I connect to the internal phone system unless I use in the in-built file explorer.
Click to expand...
Click to collapse
Try the drivers from this site
http://forum.xda-developers.com/showthread.php?t=2785089
ludoke said:
Try the drivers from this site
http://forum.xda-developers.com/showthread.php?t=2785089
Click to expand...
Click to collapse
Using the drivers on that page you have advised gives the following.
Device Manager shows a Warning on it in USB controllers as "LGE Mobile USB Composite Device". It automatically "malfunctions" according to Windows 10 and I can't change the connection interface on the phone.
Going into the properties on that device in Device Manager lists the following;
This device cannot start. (Code 10)
A device which does not exist was specified.
http://forum.xda-developers.com/lg-g3/help/answer-windows-8-8-1-detecting-lollipop-t2967574
This also works for win 10
If u find this helpful rember the thanks button
TheMadScientist420 said:
http://forum.xda-developers.com/lg-g3/help/answer-windows-8-8-1-detecting-lollipop-t2967574
This also works for win 10
If u find this helpful rember the thanks button
Click to expand...
Click to collapse
This didn't work. Already tried
Fixed my problem
I've had the same issue with my LG G3 in being unable to connect the device to my laptop. I'm not sure if the cause was a phone software update or the upgrade from Windows 8.1 to Windows 10. Either way, I searched and fixed it tonight by installing updated drivers. Hope this helps others as well.
Hmmm, I cannot post the link! technobuzz dot net lg g3 drivers
To prevent spam on the XDA forums, ALL new users prevented from posting outside links in their messages. After approximately 10 posts, you will be able to post outside links. Thank you for understanding!

[solved] Windows 10 MTP no longer working

My Surface Pro 4 with Win10x64 suddenly refuses to see my 5X in MTP mode. I installed ADB and drivers some time ago and everything was working. Now, however, I can only see the phone in device manager, explorer and ADB if I choose PTP. My PC with Win7x64 still works fine with the same cable and MTP/ADB.
The werid thing is that, in MTP mode, the Nexus doesn't even show up in device manager. Nothing at all, no unknown device, no Nexus, no ADB, no nothing.
Maybe a recent WinUpdate broke it, but since the device manager can't see the phone, I'm lost. Any ideas?
Update: I fixed it. The 5X was listed under "Marshall London Device->ADB...". Manually updating the driver did not work, it only threw up an error "not x64 compatible". However, after uninstalling this ADB device with "delete driver" checked, it started working again.
To prevent happening this in future, you can use this tool to block updating the driver automatically.
Just Win10 magic
przemcio510 said:
To prevent happening this in future, you can use this tool to block updating the driver automatically.
Just Win10 magic
Click to expand...
Click to collapse
Thanks, that might come in handy. I knew you can completely disable auto driver updates, but didn't know about blocking specific drivers.

Help usb and fastboot not reconized

I am getting a Unknown usb device (device descriptor request failed) It keep telling me usb device not recognized while being plugged it. I have tried several things
1. another windows 10 computer worked the first time then same error as a laptop.
2. unintalled the driver and rebooted.
3. also used multiple usb ports
cant find anything after searching
pixel 2 xl 8.0 September update
rooted lastest magisk 15.3
latest twrp installed
stock kernel
recently a fresh install a few days ago because i got it to work somehow but not anymore what do i do?
adb, fastboot, and storage cannot be accessed
Try these steps:
-uninstall previous version of SDK tools from PC
-download latest SDK Tools from HERE
-have a USB 2.0 cable available
-follow these steps to verify connectivity
see if these things help
Unless there is a specific reason you're still on Sept 8.0, I'd take this chance and upgrade to lasts 8.1 factory image.
evanxalmighty said:
I am getting a Unknown usb device (device descriptor request failed) It keep telling me usb device not recognized while being plugged it. I have tried several things
1. another windows 10 computer worked the first time then same error as a laptop.
2. unintalled the driver and rebooted.
3. also used multiple usb ports
cant find anything after searching
pixel 2 xl 8.0 September update
rooted lastest magisk 15.3
latest twrp installed
stock kernel
recently a fresh install a few days ago because i got it to work somehow but not anymore what do i do?
adb, fastboot, and storage cannot be accessed
Click to expand...
Click to collapse
I'm just spitballing here but....
With phone plugged in, on your pc, under device manage. When you open it up do you see unknown android device? That driver may need to be updated. Also, USB debugging is on, and the option to transfer files? Is your SDK platform-tools up to date?
I forgot to mention downloaded the platform tool for both computers. I never updated because i had root and nothing new was that interested enough to start all over. I followed the steps and nothing usb debugging is on. In device manager its says Unknown usb device (device descriptor request failed). I cant transfer files or anything. I tried updating to the google driver but it said it wasnt compatible.
I haven't seen it with this phone yet, but try changing the USB mode on your phone from the notification; I've had a few phones that refuse to work in specific modes.
evanxalmighty said:
I forgot to mention downloaded the platform tool for both computers. I never updated because i had root and nothing new was that interested enough to start all over. I followed the steps and nothing usb debugging is on. In device manager its says Unknown usb device (device descriptor request failed). I cant transfer files or anything. I tried updating to the google driver but it said it wasnt compatible.
Click to expand...
Click to collapse
Have you tried a different USB-C-A cable just for the heck of it. May have to factory reset and see if that solves it.
evanxalmighty said:
I forgot to mention downloaded the platform tool for both computers. I never updated because i had root and nothing new was that interested enough to start all over. I followed the steps and nothing usb debugging is on. In device manager its says Unknown usb device (device descriptor request failed). I cant transfer files or anything. I tried updating to the google driver but it said it wasnt compatible.
Click to expand...
Click to collapse
So your driver is messed up. Did you use the driver below?
https://dl-ssl.google.com//android/repository/latest_usb_driver_windows.zip
Sent from my taimen using XDA Labs
It won't let me install the driver I get some kind of error when selecting it. I was able to get it to work after plugging it in and out. Now that I updated to 8.1 everything was fine untill I got home. Now it's doing it again. I tried 2 different cables restarted my computer and laptop and can't figure out why it was working fine before without doing anything different.
Try this:
1. Go to C:\Windows\INF
2. Find the file "wpdmtp.inf"
3. Right click the file and click 'Install'
4. Once that is done, simply plug your phone and it should work.
JimSmith94 said:
Try this:
1. Go to C:\Windows\INF
2. Find the file "wpdmtp.inf"
3. Right click the file and click 'Install'
4. Once that is done, simply plug your phone and it should work.
Click to expand...
Click to collapse
This definitely worked for me -- Thanks for posting!
I am having sort of the same problem. I was on Android 11 on my 2xl, rooted with fast boot boot twrp.Img and installed magisk and super super, all latest. I could not get gaps so I used Android flash tool to attempt to go back stock and it downloaded and flashed it but it is now stuck in loop, I reboot to recovery and it’s stock now and it will not be recognized by adb or fast boot,!0plesase help

Categories

Resources