nexus 7 digitizer area? - Nexus 7 (2013) Q&A

I'm planning on doing a nexus 7 2013 install on my car, but the area I've got to install the tablet is really limited. Ideally I'd have to cut ~1 cm off the lower corners of the nexus.
After watching a bunch of teardown videos, I can see I'll have to relocate the wifi module, and some of the other boards which is no big deal.
The only issue is the digitizer. I won't be cutting nearly far enough to go into the screen, but will cutting the corners off break the digitizer, or is it only active above the lcd?
i.imgur.com/ySop52N.jpg
i.imgur.com/9abdPrZ.jpg
the location in question:
i.imgur.com/2AqCjvd.jpg

How do you plan on cutting the digitzer and not the lcd ? ....you better find some other way ... Perhaps a custom enclosure ....
What car is it ? Post a pic of your dashboard cause there has got to be some easier way .
Sent from my HTC One_M8 using XDA Free mobile app

the lcd is only in the center of the device - i01.i.aliimg.com/img/pb/727/355/522/522355727_328.jpg
I can't post external links yet, not enough posts. That last imgur link in the original post is a pic of the dash. The car is an acura nsx.

neonshaun said:
the lcd is only in the center of the device - i01.i.aliimg.com/img/pb/727/355/522/522355727_328.jpg
I can't post external links yet, not enough posts. That last imgur link in the original post is a pic of the dash. The car is an acura nsx.
Click to expand...
Click to collapse
You'd be far better off setting up a custom mount for the device to avoid cutting across the screen and moving parts inside the chassis. What you're proposing is likely to damage your tablet to a point that the whole process would've been a waste of time. Honest opinion.

quickdraw86 said:
You'd be far better off setting up a custom mount for the device to avoid cutting across the screen and moving parts inside the chassis. What you're proposing is likely to damage your tablet to a point that the whole process would've been a waste of time. Honest opinion.
Click to expand...
Click to collapse
Nah, I'm not planning on cutting across the screen, I'm planning on cutting the corners off the plastic in front of the screen that contains the digitizer... but I don't know if the digitizer is only active in the center over the screen, or if it needs to be continuous all the way to the edges of the tablet.
A custom mount isn't gonna happen, it has to look like it came integrated into the console, not smacked on top...

^Then you probably need to take the dash out and fit it in from the back. Cutting the glass is unlikely to end well. If you did do it without breaking the screen I don't know if the digitizer would still work. It probably would.
There is no "plastic in front of the screen that contains the digitizer" unless you're talking about the tiny bezel/backshell. It's all glass.
Edit: If the red lines on the picture are your cuts yes it will work fine. Problem is there's no way in hell you're cutting that without breaking the rest of the screen. Well I guess you could. Post pics if you try!

Related

[Q] xperia play disassembly guide?

Hello!
Has anyone seen a disassembly guide / dismantlling guide for an xperia play? I have had a quick look and havent seen one. A video one would be really good and one that looks at the digitizer / glass would be best for me as I seem to have broken mine already, oops!
Cheers
That sucks.
If you have Rogers they have a replacement policy. I would try that before you take it apart. Good luck. I haven't seen any guides yet. It is a pretty new phone.
You have a teardown here, it may be useful: http://www.ubmtechinsights.com/teardowns/sony-xperia-play-teardown/
I have found this, but would still like to see a video if one exists?
http://www.repairyourmobile.net/sony-ericsson-disassembly/sony-ericsson-xperia-play-disassembly/
Cheers
You can get a brand new OEM Sony Ericsson Touch Digitizer Screen on eBay from here: http://cgi.ebay.ca/OEM-Touch-Digiti...ultDomain_0&hash=item27bb11025c#ht_4868wt_905
I just ordered an OEM Xperia PLAY Black Housing Set from them and it's on its way. Funny how those "takedown" photos don't show you how they disconnected the sliding screen from the gamepad base. I got stuck at that part and have no idea how they were able to remove it. LOL
Rogers replacement policy doesn't give you the same model.... They have designated refurbished models available at no cost per person per life... You can only use it once... Unless the customer support was lying to me, that is what she told me.
Sent from my R800i using XDA App
Have you dealt with rogers before? The have no issue flatout lying to your face. I cant tell you how many times I got screwed over by those ****ers. So I get the feeling you'd be SOL
Sent from my R800i using XDA App
The only reason I switched over to Rogers was to get the Xperia PLAY for $99.99 on a 3 year agreement. I've been with Fido eversince and even though they're owned by Rogers now, I can say that Fido deals with their customers way better than Rogers does. When my 3 year agreement is done I'm going back with Fido. I already network unlocked my Xperia PLAY so if I still have it by then all I have to do is get a Fido SIM card.
Xperia Play disassembly pictures
Hey,
I am in the middle of taking apart my Xperia Play to replace the screen. Now, I got everything separated and taken apart except the screen half. I am having problem removing these silver rivets, which look like screws with a covering but the covering doesn't peel/come off. I have attached pictures of these in hopes that someone knows how to remove them.
Additionally, if anyone has experience replacing an Xperia Play screen, I'd love the advice.
Thanks in advance.
McD
Screen
Hi
Dont take the rivets OFF! If you just slide the control pad part off the metal casing you can get to the 2 screws you need to get to.
I have just finished replacing my screen and it is the scariest screen i have ever replaced as you need to go from back to front lol
I have attached a pic of my finished product, sorry i should of taken photos during it but i was shaking lol
Flava0ne said:
The only reason I switched over to Rogers was to get the Xperia PLAY for $99.99 on a 3 year agreement. I've been with Fido eversince and even though they're owned by Rogers now, I can say that Fido deals with their customers way better than Rogers does. When my 3 year agreement is done I'm going back with Fido. I already network unlocked my Xperia PLAY so if I still have it by then all I have to do is get a Fido SIM card.
Click to expand...
Click to collapse
I desperately hope that you did not get locked down to a 3 year agreement to just get this phone. As fun as this phone is (and likely to be used long past when I get another phone, just for Emulators and random games), it is not worth a 3 year contract. 2, I can understand. 1 would be more proper. 3 years is nuts in this industry. They have made back their offset of cost within 1.5 years usually.
Video!!
Hi
For anyone else who might benifit from this, here you go:
http://www.youtube.com/watch?v=-3n5ZfkqhzE
Edd
eddieo said:
Hi
For anyone else who might benifit from this, here you go:
http://www.youtube.com/watch?v=-3n5ZfkqhzE
Edd
Click to expand...
Click to collapse
Thanks for that video link, I think it'll really help other people who might need to do some repairs on their own to their Xperia PLAY. I just wish that I came across that video earlier when I had to disassemble mines, I was so nervous when I was doing it cause all I had to go by where those pictures posted earlier and it left out a whole lot that I had to figure out myself.
Replacing Digitizer
Hello, Flava0ne
Do I have to take entire phone apart to replace digitizer? Is there simpler way to do it? Screen is fine - only digitizer is broken. Can it be removed from the top or bottom top access only?
Thank you
WOW sorry, too many tabs open. Wrong topic!!!
(Disregard this post)
Two questions: How far can you go without breaking a warranty seal and how many internal water damage indicators / liquid sensors are there? I just need to check since they are threatening $300 if they find anything and I work in the cold and frequently see condensation. I do avoid condensation actively and don't even allow it in the bathroom when showering.
---------- Post added at 03:01 PM ---------- Previous post was at 02:03 PM ----------
OK, I went as far as I dared by completely taking apart the bottom piece (gamepad, camera, microSD slot, SIM slot, headset/remote jack, primary and secondary microphone, antennas, speakers, microUSB, etc) and, so far, I have found three. It was pretty easy up to this point and I didn't notice any kind of warranty seal.
I just removed all T6 screws from the back and lifted the catches along the bottom (headset/microUSB) side using my fingernail. One corner should be loose and you can start there and slide with no marring (didn't need my plastic pry tool). I don't know why, exactly, but the internal L & R switches are stuck to black adhesive films covering openings in this black piece but I was able to lift and unstick them without touching the films. Anyway, when you remove and flip this piece over, you should see a white square just below the mSD and SIM card slot. It's actually visible through a pinhole on the other side. If it's pink/red, you've got a problem, even if it's caused by condensation (they will still void your warranty for "water damage"). When I touched it, a plastic film on the back slipped off but stuck back on. The whole thing seems like it peels off quite easily.
Anyway, I would wiggle the power button loose before moving on. Next, there are now two tiny cross-head screws that I used a PH00x50 driver on. Yes, one of them was clearly accessible as soon as you removed the battery, but why remove it until you are ready to remove both? Once those are out, let the headphone jack dangle off its ribbon cable and lift the PCB enough to disconnect the display connector from the PCB... just stick something wide and flat in there and twist. Be careful not to damage the tiny ribbon cable that connects the touchpad area from the gamepad because it still needs to be disconnected. Now, this is OPPOSITE of how many larger but similar connectors work, so pay attention: To disconnect it, locate the tiny darker-colored flap of plastic on the opposite side of the connector from where the cable goes in. Lift it from the opposite side toward the side where the cable inserts. It will stand straight up and then you can slide the cable out. If you have to remove it, the headphone/remote jack appears to work the same way.
Anyway, this should completely free the PCB and leave the gamepad shell attached to the display. The gamepad shell should be free from the front half of the phone now as well, leaving only the sliding metal mounting bracket.
Now, a couple of interesting things here: I can clearly tell that one of the T6 screws by the volume button was protruding too far and caused a visible sliding scratch on the underside of my top shell. It may make sense to loosen these a bit on a new phone before this happens. You can also see if imperfections in the white Teflon sliding bumps are causing scratches on the front (my first phone did not, my second did in no time).
Now, let's go back to the gamepad faceplate. The buttons should easily fall out if you want them too, but I was only interested in finding the water sensors and here are two more: one is right by the microphone hole and the other in diagonally opposite under the Playstation Certified logo. They look identical to the one on the back piece.
I'm sure that there is at least one in the LCD assembly as well, but mine is well sealed and I didn't want to lift any of those silvery-gray stickers covering the screws when I have a warranty replacement on the way. I've gone far enough to satisfy my curiosity.
---------- Post added at 03:51 PM ---------- Previous post was at 03:01 PM ----------
A couple notes on re-assembly:
As expected, it's a bit more difficult, especially because you don't have leverage to reconnect the display when it is in place. The last fold of the cable it supposed to fit UNDER the metal bracket and the slide mechanism doesn't really work if it isn't (a certain panel will not slide back if it is not folded under). I'm not sure how it affects it but it does. You will need a thin, long, flat utensil like a plastic butter knife or something to either A) provide leverage to connect the connector or B) tuck the cable back under the bracket after connecting it. You need to have already connected the touchpads and oriented the gamepad faceplate around/under the bracket, though it will not be secured. The phone also needs to be in the open position. When you tuck the cable under, slide it to the closed position and back. If the cable seated properly, the PCB and gamepad faceplate should sit pretty flat and should no longer be falling off of the bracket even though it isn't really secured.
The D-pad needs to be arranged properly as well. One side is cut. If you look closely, there are three holes in the four inner corners that align with three plus-shaped pegs, so you can't get it wrong if you pay attention.
The power/lock button isn't going to stay in place until you secure the bottom housing, so leave it off until just before you are ready to do that to avoid losing it.
Be careful not to seal dust in the camera lens. Don't forget to put the cross-head screws back before you do the back housing because you can't easily access one. Remember to keep the four black screws by the L, R, and volume buttons a little loose if you had a problem with them scratching the other half of the phone.
Be sure to download the Xperia Play test program from the Google Market and verify that all buttons and touch inputs function properly.
I'll be sure to wear my Looxcie next time.
I feel sorry for you blokes taking apart the xperia
it's going to be a royal pain in the ass. especially when you reach that "point"
the point where you have **** all over the table and you are like god how did i get this deep into disassembly
then the part when you are shaking / nervous about breaking a part, or worse yet. you end up breaking it. i would be real scared lol.
all i can say is go real slow. REAL slow
and if anything wont move. dont force it lol
Hogwarts said:
I feel sorry for you blokes taking apart the xperia
it's going to be a royal pain in the ass. especially when you reach that "point"
the point where you have **** all over the table and you are like god how did i get this deep into disassembly
then the part when you are shaking / nervous about breaking a part, or worse yet. you end up breaking it. i would be real scared lol.
all i can say is go real slow. REAL slow
and if anything wont move. dont force it lol
Click to expand...
Click to collapse
Maybe I've just taken apart too many laptops and gadgets before but I never felt that way when I got the back piece completely apart... or maybe "that point" is only after you get into the front assembly. I did the rear in bed with the screws laying on the covers beside me and didn't even lose the arrangement of a single one.
Anyway, moments after getting my RMA replacement shipped email notification this morning, I dropped my R800at that is supposed to be getting sent back and now the touch digitizer is shattered. I've ordered a replacement but I'm hoping that I'll be sending it back with the original from the RMA replacement. Does anyone know if the R800a or R800at will fit a R800 Z1i chassis? These are all over eBay. Also, is there any tamper seal? I understand that there are screws under the silver/gray stickers on the front piece but those look easy enough to reapply.
Did I mention that they wanted to turn my RMA down for the flaking paint on the front buttons alone? The night before I called to RMA for an alarm issue (two days ago), the battery door cracked right at the pry point. I remove it more often than most because I carry a second official battery and a Sony Ericsson EP900 charger, so it failed under normal wear-and-tear, but they wanted to say that I couldn't RMA for my main issue (alarm dismisses itself) because of that EVEN THOUGH THE RMA UNITS DON'T INCLUDE A BATTERY COVER!
Damn. Sony Ericsson can be picky. I babied the thing and only just now dropped it. Perhaps AT&T is a little too cautious with the terms of Sony's warranty (it is processed through them but the rules come from Sony).
CZroe said:
Maybe I've just taken apart too many laptops and gadgets before but I never felt that way when I got the back piece completely apart... or maybe "that point" is only after you get into the front assembly. I did the rear in bed with the screws laying on the covers beside me and didn't even lose the arrangement of a single one.
Anyway, moments after getting my RMA replacement shipped email notification this morning, I dropped my R800at that is supposed to be getting sent back and now the touch digitizer is shattered. I've ordered a replacement but I'm hoping that I'll be sending it back with the original from the RMA replacement. Does anyone know if the R800a or R800at will fit a R800 Z1i chassis? These are all over eBay. Also, is there any tamper seal? I understand that there are screws under the silver/gray stickers on the front piece but those look easy enough to reapply.
Did I mention that they wanted to turn my RMA down for the flaking paint on the front buttons alone? The night before I called to RMA for an alarm issue (two days ago), the battery door cracked right at the pry point. I remove it more often than most because I carry a second official battery and a Sony Ericsson EP900 charger, so it failed under normal wear-and-tear, but they wanted to say that I couldn't RMA for my main issue (alarm dismisses itself) because of that EVEN THOUGH THE RMA UNITS DON'T INCLUDE A BATTERY COVER!
Damn. Sony Ericsson can be picky. I babied the thing and only just now dropped it. Perhaps AT&T is a little too cautious with the terms of Sony's warranty (it is processed through them but the rules come from Sony).
Click to expand...
Click to collapse
I've always said this phone is cheaply made and now i have more proof
mine came brand new out of the box with a blemish on the screen
I'm not picky so i just kept it.
Its a blemish in the LCD screen not the digitizer or glass
and yeah the cheap ass plastic assembly is not helping either.
they should have used aluminum or something. more durable
OK, so I finished the job. I did not see any more water indicators in the top shell and I did not find a single tamper-resistant label in the entire device. I left the slider assembly intact (I think it's riveted) and I didn't peel the flex PCB out of the top shell or off of the touchoads, but it was what anyone would consider "fully disassembled." I seem to have misplaced my camera but video will be coming when I find and edit it.

How to Replace your Scratched Galaxy S2 Screen DIY

I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!
thanks for the write up, do you have any more photos of your process?
OMG, it's like watching an autopsy.
Could a better resolution screen or even 3d screen be used/upgraded later on?
Nice to know for something happens, Hope not
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.
On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App
wow that is the definition of T H I N !!!!!
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site
psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.
I wonder how these replacement parts compare to the quality of the original parts.
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.
It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.
BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL
Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.
I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB

Digitizer replacement

Hi, has anyone replaced their digitizer on their desire z/g2? How did it go? It looks easy on the youtube vid.. have any problems? What way did you use to melt the glue? What digitizer did you use, where from?
Any info much appriciated as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Thanks..
Sent from my HTC Vision using XDA App
Never done it on a g2 but should be pretty straight forward especially with a video lol. Use a heat gun to melt the glue, pretty much the only tool you SHOULD use to do something like that.
I replaced the digitizer on my third G2 after getting a refurb replacement from T-Mobile that had a black spot inside the actual digitizer glass, not on the outside or inside.
The process is very easy with the video, however, trying to keep dust and fingerprints from getting on the inside of the phone while you're trying to get it back together is a serious pain in the rear! If it's the same video that I watched, just use a hair drier blowing hot air to heat the adhesive on the inside of the digitizer and then pop the digitizer off very very slowly, because you don't want to accidentally bend the metal bezel around the screen.
You also may want to leave the original leftover adhesive on the inside, because when I cleaned mine off, light now always leaks out around the bottom edge of the digitizer, below the menu, home, and search buttons, even though I used the double sided adhesive strips covering the entire length of the bottom, so light shouldn't technically be leaking out. No biggie, though... it works like brand new, now!
Thanks for the reply.. I have seen that video and that's what I was using as a guide.. I ordered the digi today, should be here tomorrow.. the only thing I was wondering was the glueing process, as I have not ordered the double sided glue/tape stuff, as I was just hopeing to still use the original glue as I think you are saying.. I hope that works! Have to be careful like u say with dust/fingerprints etc..
Sent from my HTC Vision using XDA App
Hmm, after reading your post again, maybee I should of bought the double sided tape afterall? Do you think the old leftover glue is enough for the new digi?
Many thanks..
Sent from my HTC Vision usingall XDA App
Run over to radio shack they must have some kind of glue you can use lol. google cell phone screen glue see what info you can find.
Ok, just incase anyone is interested, got my new digitizer, followed the video, used a heat gun cerfully to melt the glue, pulled the old digitizer out, and used the original glue whilst still warm to hold the new digi in, as all of glue stayed on the case rather than on the digi, which was pretty lucky.. put it all back together and everything perfect, touchscreen back to how it should be.. cost me 17 pounds.
Sent from my HTC Vision using XDA App
How was this accompilshed?
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
So which digitizer did you end up buying and which guide or video did you follow? I am about to tear mine apart and could use the info.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
Hi, I did buy mine from amazon.co.uk, there were a few for sale,, the one I bought was supposed to be a genuine t-mobile g2 replacement (refurb I think, pressumably this just means that it was from a second hand g2 that had problems and the digi was taken out - and I'm pretty certain this is the case as mine has a thin film (which u leave on) over the back of the digi covering the tracks etc, which had a few very small air/dust bubbles under it (just noticeable when screen off), where I own a desire z, so now it sais t-mobile instead of htc, but I can live with that.
The small grey bits that you talk about were floating about or stuck on my digi when I pulled it off the main chassis. I had a look, and as far as I could work out, were possibly just for giving colour to the tiny led's that give you light to the home/search keys etc (I may be wrong on their use), but if you look closely, the tiny grey things have even smaller rectangles on them that relate to the positions of the led's on the circuit board. So I picked the remaining ones off the old digi, put them back in their correct holes and stuck the new digi in. I've had no problems (with a digi from amazon with no little grey things on it) so far, but maybee this is due to mine being a second hand original part..
Edit : Now after reading your post again, you're talking about bits that are actually on the digi itself, not the white caps that I'm talking about! Whoops. I didn't notice any grey spots on the digi itself, but I guess I must have them..
Sent from my HTC Vision using XDA App
ian577416 said:
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
Click to expand...
Click to collapse
I rekon u replaced the wrong thing! Maybe the lcd?
Sent from my HTC Vision using XDA App
i just replaced mine with this one:
http://www.ebay.de/itm/230685692541?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
actually it says HTC on it and looks a lil bit differently than on the picture.
never the less, i replaced it really carefully and checked every connecting.
But somehow the Touchscreen doesn't work at all.
Can anyone help me ? what could be the problem ?
Wrong digitzer ?
is it okay, that the digitizer has direct contact to the frame where it is glued to ?
jmpcrx said:
... as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Hi!
I have the same problem, I have asked it already here
So you had invisible finger press in the screen, and the screen was bad responsive?
...Just to make sure my problem is digitizer problem! The service wont change it in warranty unless the problem is there all the time! But its driving me crazy! why is it happening randomly, why isnt it all the time? How could i make the screen to do this problem when i'm at the service?

Bubbles under digitizer? No screen protector

Hi all. Quick searching leads me nowhere as there are thousands of problems concerning issues I'm NOT having. Sorry for the crappy 3ds camera pic, it's the only thing I have at my disposal right now besides the phone. As I said in the title, I'm not using a screen protector - this is a stock phone right out of the factory with no accessories, albeit aged a bit.
If you'll take a look, you'll see two screen bubbles. The huge funky-looking one at the top started out looking like the one at the bottom, and grew over a period of a few weeks. The bottom one started out really small and doubled in size to what it is now, but has since stopped.
It's really annoying and starting to bother me, but I was wondering if anyone had experienced similar issues, or has any input whether or not I can maybe fix this thing without having to get a whole new screen/digitizer/whatever. No replacement plans on this phone so gotta figure something else out. Any idea what's going on?
D-Lew said:
Hi all. Quick searching leads me nowhere as there are thousands of problems concerning issues I'm NOT having. Sorry for the crappy 3ds camera pic, it's the only thing I have at my disposal right now besides the phone. As I said in the title, I'm not using a screen protector - this is a stock phone right out of the factory with no accessories, albeit aged a bit.
If you'll take a look, you'll see two screen bubbles. The huge funky-looking one at the top started out looking like the one at the bottom, and grew over a period of a few weeks. The bottom one started out really small and doubled in size to what it is now, but has since stopped.
It's really annoying and starting to bother me, but I was wondering if anyone had experienced similar issues, or has any input whether or not I can maybe fix this thing without having to get a whole new screen/digitizer/whatever. No replacement plans on this phone so gotta figure something else out. Any idea what's going on?
Click to expand...
Click to collapse
Is the plastic actually raised up? Can you see it when the screen is off? To me it looks like the digatizer may be going out, but its hard to tell from a pic.
It appears to be sealed and working fine... just has bubbles. I don't really know much about the insides of this phone, but it almost looks as if whatever is behind the digitizer is slightly warped and might be causing some contact with the glass or something like that. Reflections (off what is behind the screen - lcd? Not the reflections off the glass) tend to bend near the bubbles, whereas everywhere else behind the glass is pretty straight.
Essentially it just looks like water droplets or air bubbles forming on the inside surface of the glass, but it's never seen water before. I don't think the digitizer is failing.
Same problem, can I fix this myself?
Hi guys, I have the exact same problem on my HTC Desire. Touch is working fine, the pixels underneath are ok... yet this thing is expanding. What used to be 3 little bubbles near the very corner moved and turned into this amoeba looking thing after a few months.
Here are a few other shots.
Hope someone can let me know the possible verdict? Is it gone? Can it only be repaired by a professional or can I expect to be able to "clean up" the inside of the screen if I dismantle my phone as it is done here?:
http://forum.xda-developers.com/showthread.php?t=1566313
Maybe the liquids from the lcd are boiling from the heat? Sounds dumb but is a possibility
Sent from my ADR6300 using xda app-developers app
Yikes. Mine is still having the same issues. I'm thinking about just tearing it down soon and figuring it out myself. A little nervous working on something with such small components. Any tips for a first teardown? I need to get a T6 torx and I've already looked at a couple disassembly guides, was a while ago though.
As far as I can tell, I will have to replace either the digitizer/glass or the LCD. If it's the latter I'll probably just upgrade the phone cause they seem pretty pricey.
Ok, I did what I said and investigated myself. Unfortunately, I broke my phone doing it.
The problem is the front glass/digitizer. I couldn't get the LCD off, but I pried it back enough to see bubbles through the glass looking from the inside.
I broke my LCD prying on it, now I have an ugly black spot. Guess I'll be buying an LCD and a digitizer now. Anybody have some spare ones, or know the cheapest place to get them?
D-Lew said:
Ok, I did what I said and investigated myself. Unfortunately, I broke my phone doing it.
The problem is the front glass/digitizer. I couldn't get the LCD off, but I pried it back enough to see bubbles through the glass looking from the inside.
I broke my LCD prying on it, now I have an ugly black spot. Guess I'll be buying an LCD and a digitizer now. Anybody have some spare ones, or know the cheapest place to get them?
Click to expand...
Click to collapse
There are some digitizers on ebay for about $20 USD. i dont know about LCDs cause i never needed to replace mine but i would assume that they would be a little more expensive. Also, make sure you get the digitizer WITH the bezel because it will make your life a ton easier.
I'd better not touch it then
Sorry to hear about your LCD, D-Lew
Guess I wont be touching mine on my own. I'll definitely break it trying to do the same thing as you. I wonder if it's gonna break my phone if I just leave it as is. I mean, apart from the fact that it is there, it is not affecting the performance at all.
The bubble might get bigger. That's all you have to worry about.
Sent from my GT-P3113 using xda app-developers app

How to replace just the glass lens on the at&t galaxy s3

Pretty much all you need in the title. I wanted to know how to do this mainly because it's cheaper then buying a lCD digitizer combo and because I can't find a guide anywhere else. Any tips and tricks on how to do this should be well appreciated and any guides. Thanks in andVance for anyone's help.
Sent from my SAMSUNG-SGH-I747 using xda premium
Backslash10 said:
Pretty much all you need in the title. I wanted to know how to do this mainly because it's cheaper then buying a lCD digitizer combo and because I can't find a guide anywhere else. Any tips and tricks on how to do this should be well appreciated and any guides. Thanks in andVance for anyone's help.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
I also have a cracked the screen, What my search result has come up with is the cost to replace the screen is ~$200CDN. Can you please keep me posted on what path you would be taking, might just follow
Replacing the glass from the actual screen is very hard and would require tons of technical know-how because the two are fused together.
Not recommended, even by experts.
Well I know it's extremely hard but I'm mainly looking for advise about it is all it decently help people out here.
Sent from my SAMSUNG-SGH-I747 using xda premium
Backslash10 said:
Well I know it's extremely hard but I'm mainly looking for advise about it is all it decently help people out here.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
it's not possible to do. period.
Really I thought I could be done but took a lot of waiting and just the right heat and pressure.
Sent from my SAMSUNG-SGH-I747 using xda premium
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
Nice
Op
http://forum.xda-developers.com/showthread.php?t=1904554
it is very possible I have done 4 of them already...
http://forum.xda-developers.com/showthread.php?t=1890708
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
hahahah.....owned, should really atleast attempt to find out if what you are saying has any evidence to support it, or rebut it
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
I've heard its possible, just EXTREMELY difficult to manage.. I wouldn't.
Its entirely possible, as the multiple video's have shown. Although i haven't done it to the SGS3 yet, i will be soon. Cracked my lens the other day, replacement in the mail. I have also changed the screen's on several iphones (at my job) which us a similar method of gluing. It is made to be difficult by design...to keep people from attempting it and opting to send it in for repair. Of course when you do this, through samsung anyways, you are being charged for the entire led assembly and not just the lens.
dntesinfrno said:
Its entirely possible, as the multiple video's have shown. Although i haven't done it to the SGS3 yet, i will be soon. Cracked my lens the other day, replacement in the mail. I have also changed the screen's on several iphones (at my job) which us a similar method of gluing. It is made to be difficult by design...to keep people from attempting it and opting to send it in for repair. Of course when you do this, through samsung anyways, you are being charged for the entire led assembly and not just the lens.
Click to expand...
Click to collapse
Good to hear you did it at your job with iphones. Any idea what glue they use to bond the glass to the digitizer? I have searched and searched and cannot find anything. I have done several S3 so far and this is the one ingredient lacking for a complete repair. In terms of what it feels like while removing the old glue; it seems to be silicone based the way it comes up, you can roll it into little balls, it's is tacky and has that rubbery consistency.
Unfortunately, no idea what adhesive they use. Personally i would attempt what YellowGTO did first and simply heat the existing glue and see how it holds. Normally this should be enough to do the job, as you can imagine the stuff if pretty tacky. Especially if the lens fits as tightly as his in the video, its doubtful it will fall out even with the slightest remaining glue. If for whatever reason there isn't enough to firmly hold the screen in place i've used small dabs of liquid tape where necessary, or the thin 3M double sided tape would work also i suppose. In this case i usually wrap the device in a towel or shirt or whatever you have laying around and set something with some decent weight on top of it, screen side down on a flat surface, overnight to give the adhesive time to setup properly.
dntesinfrno said:
Unfortunately, no idea what adhesive they use. Personally i would attempt what YellowGTO did first and simply heat the existing glue and see how it holds. Normally this should be enough to do the job, as you can imagine the stuff if pretty tacky. Especially if the lens fits as tightly as his in the video, its doubtful it will fall out even with the slightest remaining glue. If for whatever reason there isn't enough to firmly hold the screen in place i've used small dabs of liquid tape where necessary, or the thin 3M double sided tape would work also i suppose. In this case i usually wrap the device in a towel or shirt or whatever you have laying around and set something with some decent weight on top of it, screen side down on a flat surface, overnight to give the adhesive time to setup properly.
Click to expand...
Click to collapse
Sure the outer frame is enough in most cases to hold it on, thats fine. But there is a side effect once all the glue is removed off the digitizer. There will a micro gap between the 2 when the original glue is removed. If you press the new glass hard enough, ( for example cleaning fingerprints like I often do against my shirt ) and it touches the digitizer, the phone freezes. You must then power off the screen, sleep button and then press power again to bring it up and then it will work again. Seems to be a recalibration process going on.
Maybe these 2 posts should be merged and I would certainly read the post below. Much more good info here on the subject...
http://forum.xda-developers.com/showthread.php?p=33056057#post33056057
Yea, i've been following several threads about lens replacement, even before i busted mine (jinxed myself?). I'd much rather have to deal with a 15 second reboot over possibly damaging the LED or worse using an adhesive that may not be transparent. I can live with the air gap, or even the 'invisible' smudges on my personal device...although if i were going to do this for profit obviously that would be unacceptable. 20 dollars and an hour of my time vs 200+ for the whole assembly or 125 for an insurance deductable..i can overlook imprefections . It would be interesting to find out exactly what substance they are using though.
EDIT - Just for SnG's i googled 'mobile screen glue' and this was the first result. http://www.alibaba.com/product-gs/523467689/Optical_Clear_Adhesive_for_touch_screen.html?s=p
While i'm sure its not the only product out there for this purpose, if this is any indication it won't come cheap..
dntesinfrno said:
Yea, i've been following several threads about lens replacement, even before i busted mine (jinxed myself?). I'd much rather have to deal with a 15 second reboot over possibly damaging the LED or worse using an adhesive that may not be transparent. I can live with the air gap, or even the 'invisible' smudges on my personal device...although if i were going to do this for profit obviously that would be unacceptable. 20 dollars and an hour of my time vs 200+ for the whole assembly or 125 for an insurance deductable..i can overlook imprefections . It would be interesting to find out exactly what substance they are using though.
Click to expand...
Click to collapse
Agreed it would be nice to find out what type of glue.
The phone breaks so easy i am surprised I have not heard of a Class Action Lawsuit... :silly:
here are instructions on replacing just the glass/screen
[HOW TO] [TUTORIAL] S3 Replace Cracked Glass Screen w/ YouTube Video
i replaced my screen took me about 50 mins with 2 people
XeoNoX said:
here are instructions on replacing just the glass/screen
[HOW TO] [TUTORIAL] S3 Replace Cracked Glass Screen w/ YouTube Video
i replaced my screen took me about 50 mins with 2 people
Click to expand...
Click to collapse
Very very nice!! :thumbup::thumbup:
Sent from my SCH-I535 using xda app-developers app
marcustaz said:
Very very nice!! :thumbup::thumbup:
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
JUst did an even EASIER replacement for a cracked camera lens. I purchased this part from ebay :
http://www.ebay.com/itm/Blue-Housin.../271099346918?ssPageName=ADME:L:eek:C:US:3160
1) Turn phone off
2) Take off battery cover
3) Remove battery, SIM card, and SD Card
4) remove about 8 screws to remove the middle back place.
5) Remove middle back place carefully (There are still tabs holding it secure)
6) Place new middle back in place
7) Screw down
8) Replace battery, SIM card, and SD card
9) Replace battery cover
10) Power up phone!!
Took all of 10 minutes total. Flawless fix on my AT&T Samsung Galaxy S 3
Gentlemen and OP please update your original post to include this video. This is NOT to promote myself but from all the comments and feedback everyone has stated it is the most detailed and informative on You Tube on the glass replacement procedure. I also have separate videos on shattered glass replacement. Thanks and good luck.

Categories

Resources