Connection pins in the backcover - G4 Q&A, Help & Troubleshooting

On the inside of the backcover there are 2 little copper pins. Can anyone tell me what they do? Or is this just a way to detect that the back is attached or maybe NFC or wireless charging?

AFAIK, the lower two pins are for NFC.
The remaining two upper pins are for wireless charging. (need compatible back covers)

I bought Verizon G4 yesterday at Best Buy, most importantly for the camera and removable battery, but also because of wireless charging, which I've been using for about a year on my Moto G.
I had to add the coil receiver to the Moto G, and it does a very good job of keeping the phone charged. It's slow, but I work at a desk at home all day, so the phone sits on the charging puck, and speed is not an essential requirement.
I was aware before buying the LG G4 that the back had to be swapped out for a "receiver" back, but I was dismayed to learn that there doesn't seem to be such a thing available, at least here in the U.S. The only charging device available is the circle device, and that's not what I want.
When I got the phone home, I pulled the receiver out of the Moto G and slapped it into the LG G4 and tried to charge the phone. I immediately got a note saying that charging had stopped, and the add-on receiver was incompatible with LG.
So much for that idea. Anybody have any thought on anything other than the circle case??
Enzo

enzo ferraro said:
I bought Verizon G4 yesterday at Best Buy, most importantly for the camera and removable battery, but also because of wireless charging, which I've been using for about a year on my Moto G.
I had to add the coil receiver to the Moto G, and it does a very good job of keeping the phone charged. It's slow, but I work at a desk at home all day, so the phone sits on the charging puck, and speed is not an essential requirement.
I was aware before buying the LG G4 that the back had to be swapped out for a "receiver" back, but I was dismayed to learn that there doesn't seem to be such a thing available, at least here in the U.S. The only charging device available is the circle device, and that's not what I want.
When I got the phone home, I pulled the receiver out of the Moto G and slapped it into the LG G4 and tried to charge the phone. I immediately got a note saying that charging had stopped, and the add-on receiver was incompatible with LG.
So much for that idea. Anybody have any thought on anything other than the circle case??
Enzo
Click to expand...
Click to collapse
A few people on other xda threads are ordering some from aliexpress.com.
http://www.aliexpress.com/item/G4-W...ireless-Charger-Battery-Back/32359379615.html
or
http://www.aliexpress.com/item/Wire...E9aQ2fUoTXld0i5X8eQSvhtz-yu6&cn=9263&cv=15091
are a couple examples. I'm going to wait it out since I don't have a wireless charger anyways and see which one works the best with Verizon G4

Aliexpress has a supposedly compatible sticker that replace the NFC sticker on the battery cover
its also on Ebay

My Phone Not Shown
woozzy101 said:
A few people on other xda threads are ordering some from aliexpress.com.
http://www.aliexpress.com/item/G4-W...ireless-Charger-Battery-Back/32359379615.html
or
http://www.aliexpress.com/item/Wire...E9aQ2fUoTXld0i5X8eQSvhtz-yu6&cn=9263&cv=15091
are a couple examples. I'm going to wait it out since I don't have a wireless charger anyways and see which one works the best with Verizon G4
Click to expand...
Click to collapse
I pinged the link you gave, but it does not list my phone, which is a VS986. I'll have to be more clear on which contacts do, or do not line up with those on the phone.
Enzo

enzo ferraro said:
I pinged the link you gave, but it does not list my phone, which is a VS986. I'll have to be more clear on which contacts do, or do not line up with those on the phone.
Enzo
Click to expand...
Click to collapse
The first link says Verizon on it. while it does not specify the VS986, it looks like it might work. That seller also has a video for their QI charging chip install.
https://www.youtube.com/watch?v=NOxlzQGggXs&feature=youtu.be

Looks Good, I Found Similar On eBay
woozzy101 said:
The first link says Verizon on it. while it does not specify the VS986, it looks like it might work. That seller also has a video for their QI charging chip install.
https://www.youtube.com/watch?v=NOxlzQGggXs&feature=youtu.be
Click to expand...
Click to collapse
Thanks, Wooz, that looks like it will work on the VS986, but this outfit will not take PayPal, but requires a credit/debit card, and I didn't feel comfortable with anything other than PP, so I did not order from them.
I found a new listing on eBay, and ordered from that outfit, also of course in China.
I don't claim any expertise here, but it seems that the sticker needs to pick up the BOTTOM TWO contacts of the four shown to the right side of the battery. The one I purchased ($8.80, free shipping with PayPal) seems to do that. This outfit also claims its sticker contains a chip for NFC, which I've never used and don't feel is a major item just at the moment. However NFC might turn out to be helpful later, although I'm completely in the dark about its methodology.
The link I bought from is [email protected]
I'll add to this info after I receive the sticker and fumble it into the phone, although probably not as adroitly as the guy in the video.

Related

Official Galaxy S2 Desktop Dock

Does anyone know of an alternative source for this dock?
I've had it on order for a couple of weeks now, but it's still showing up as out of stock - more due shortly
Can't seem to find anywhere else that's doing it!
Thx
Bought mine from an ebay reseller and it came in a week from South Korea..
http://www.exportprive.com/samsung-desktop-charging-dock-galaxy-i9100-p-16416.html
ordered spare battery, in the uk within a week
Thanks for that both....
@benjatt - When you searched on the exportprive site for it and it gave you that price.....was that the total price, inc postage etc? It works out 2 or 3 quid extra from them but if that includes the postage as well, I'll cancel my order with mobilefun and order it from exportprive instead, as I rang MF today and they said the next shipment should be in around the 8th July (the last one that should've arrived last Monday, never turned up at all!!)
@chybinj - exportprive are based in S Korea it seems, so your item might have come from their ebay shop!
If you think you can sync data or connect with this device, stay away from this. Yes, I do have it with a gold pack SGS II...
But you can not connect to PC nor sync with it. It is just a stylish charger device for desktop that's all... It does not have own speakers it just a bigger hole that increase sound a bit also.
I was really disappointed that it can not connect at all.. Was hoping for that...
SiSL said:
If you think you can sync data or connect with this device, stay away from this. Yes, I do have it with a gold pack SGS II...
But you can not connect to PC nor sync with it. It is just a stylish charger device for desktop that's all... It does not have own speakers it just a bigger hole that increase sound a bit also.
I was really disappointed that it can not connect at all.. Was hoping for that...
Click to expand...
Click to collapse
Nope.....don't want to sync or anything...just want a nice and easy 'in-out' sliding action, into a good-looking bedside dock/charger (which, judging by the various vids I've seen of this device, it seems to give....) My current one, clunks in and out of the protruding micro-usb spiggot.....and echo's loudly off my bedside cabinet in doing so....which deffo isn't appreciated by my 'better-half', at 4.30am.....
Do ya want to get rid of yours by any chance...?
price and non sync ability is such a turn off....
Willie_Heckerslyke said:
Nope.....don't want to sync or anything...just want a nice and easy 'in-out' sliding action, into a good-looking bedside dock/charger (which, judging by the various vids I've seen of this device, it seems to give....) My current one, clunks in and out of the protruding micro-usb spiggot.....and echo's loudly off my bedside cabinet in doing so....which deffo isn't appreciated by my 'better-half', at 4.30am.....
Do ya want to get rid of yours by any chance...?
Click to expand...
Click to collapse
Ah no, it is still good "desktop clock" (it has a desktop clock function built-in within the phone -- different type of idle screen)
However, glad I did not pay anything for it extra other than phone's cost.
I can recommend this one for everybody. It is so good. Already ordered another one for my work place.
And then the one question which everybody has been thinking: Does the phone fit there if using official Samsung back cover..
I should get the cover today, so I will try it as soon as possible. Stay tuned!
i also want to buy this desktop charger but i dont know if the phone is going to fit because i am using the skinomi body skin.
Does anyone know if the phone fits to this desktop charger with the skin
prince_72 said:
i also want to buy this desktop charger but i dont know if the phone is going to fit because i am using the skinomi body skin.
Does anyone know if the phone fits to this desktop charger with the skin
Click to expand...
Click to collapse
To all those asking about fit, it's tight. I have a protective skin on mine and it just barely makes it. Anything thicker than a protector won't work.
Bought one of these from Amazon, which was supplied by expansys, even though it said delivery delays it turned up in 3 days, then they reduced to 29.95 so I ordered another one again turned up in 3 days.
Excellent bit of kit, really nice for the bed side table to.
Shame thing it does not support usb connection
CandyAndy said:
I can recommend this one for everybody. It is so good. Already ordered another one for my work place.
And then the one question which everybody has been thinking: Does the phone fit there if using official Samsung back cover..
I should get the cover today, so I will try it as soon as possible. Stay tuned!
Click to expand...
Click to collapse
Well does it fit or not?
Gavin.csy said:
Well does it fit or not?
Click to expand...
Click to collapse
No it doesn't
So I had to ditch my back cover for this. I like the dock way too much. Will receive another one for work probably on monday.
Shame with the backcover thou, also liked that one.
Sync and Dock Station
ivanlmh said:
Shame thing it does not support usb connection
Click to expand...
Click to collapse
May we hope in some fix on the phone os to enable sync functionality?
Will having the S2 attached to the official dock all the time when being at home affect battery life?
Feel like spamming every dock thread with this question.
moromirco said:
May we hope in some fix on the phone os to enable sync functionality?
Click to expand...
Click to collapse
I think we must open this dock and cut shorted pins in micro usb plug.
Shorted pins make phone thinking that's an accesory, not USB cable...
Hey guys, I got an official S2 dock, very nice but what a shame, it doesn't sync!!!!!
Anyone has tried something like this??
Disassembly: http://modmomun.blogspot.com/2011/07/disassembly-samsung-galaxy-s2-ii.html
Mod Switch http://modmomun.blogspot.com/2011/07/make-samsung-galaxy-s2-ii-desktop-dock.html
Need some thai translation hehehe
I'm looking to buy one of these, but they are too expensive for my liking, anyone know if I can get THIS for cheaper?

USB Cradle Dock with Battery Charger

My phone sits by my computer most of the time, and with my HTC Mogul, then HTC Touch Pro, then EVO 4G I've bought a combo cradle/battery charger. I haven't seen one mentioned available here for the Epic 4G Touch and I just found/bought one on eBay and thought I'd mention it for others interested in a device like this. Once I receive the item I can post a review if you guys would like.
Item Link:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270857928655
Pics:
http://jpegbay.com/gallery/001248357-1.html
Please post a review of you get a chance. We'd love to hear from your experiences.
Sent from my SPH-D710 using xda premium
This looks like the one I had for my Touch Pro 2... it worked nicely and was cheaper than the official docks.
I am interested in your impressions as well.
thanks
Question for anyone that has purchased this dock..
Have you been able to charge your phone with any type of case on it? Thanks.
Just a quick update. I got the charger, but I don't have an Epic 4G Touch yet. The first seller I bought the phone from ended up being from a scammer. I gave the dock/charger to a friend, and bought another one that's already here. I should have the Epic 4G Touch from another seller here by Tuesday and will post my impressions soon after.
Damn, sorry to hear that..
Ok guys...
Im also looking at desktop cradles and found this other one:
From an Amazon vendor:
$22 (includes shipping):
http://www.amazon.com/gp/product/B005OTXKK4/ref=ox_sc_act_title_1?ie=UTF8&m=A3CZ5XR3PIAJMS
It's basically almost the same design as the one the OP linked to. What do you guys think?
I kind of wanted one that you could rest the phone in and charge it with a cover on, but I don't think that's gonna happen.
killabee44 said:
Ok guys...
Im also looking at desktop cradles and found this other one:
From an Amazon vendor:
$22 (includes shipping):
http://www.amazon.com/gp/product/B005OTXKK4/ref=ox_sc_act_title_1?ie=UTF8&m=A3CZ5XR3PIAJMS
It's basically almost the same design as the one the OP linked to. What do you guys think?
I kind of wanted one that you could rest the phone in and charge it with a cover on, but I don't think that's gonna happen.
Click to expand...
Click to collapse
I think this one is better because you can turn your dock on its side like if you were watching Sprint TV...
killabee44 said:
Ok guys...
Im also looking at desktop cradles and found this other one:
From an Amazon vendor:
$22 (includes shipping):
http://www.amazon.com/gp/product/B005OTXKK4/ref=ox_sc_act_title_1?ie=UTF8&m=A3CZ5XR3PIAJMS
It's basically almost the same design as the one the OP linked to. What do you guys think?
I kind of wanted one that you could rest the phone in and charge it with a cover on, but I don't think that's gonna happen.
Click to expand...
Click to collapse
This one looks nice, but some of the reviews for this brand (for other phones) mentions it covers up the speaker so when the phone is docked the sounds are silenced since the speaker is at the bottom. Although this may be true for all these 3rd party docks.
It's cool, Paypal resolution against the scammer just resolved today and they sided with me and already credited my PayPal account.
---
For that other cradle from Amazon, though you probably can put it on its side I'd be concerned with the side buttons/hitting the desk and possibly being pressed in, and possibly the device itself slipping out. The other concern I have with that model is that I can't clearly see the extra battery charger compartment. The one I got should accommodate extended batteries, but I can't tell on that model.
Found this one... similar
http://www.ebay.com/itm/KiDiGi-BATT...Accessories&hash=item45ff08a39d#ht_4184wt_940
Gorguts said:
http://www.ebay.com/itm/KiDiGi-BATT...Accessories&hash=item45ff08a39d#ht_4184wt_940
Click to expand...
Click to collapse
it looks like the one from Amazon just a different brand.. it also covers the speaker so I wonder if you can hear the alarms or music... there may be enough room behind the actual phone to allow the sound to be heard, but it doesnt look like it.
Quick first impressions:
* Feels solid and fits snugly, so pay attention when docking the phone in as it aligns only one way.
* When no battery is in the battery charging slot there's a LED that flashes crazy fast green/red which may bother some people. You can always cover it up with electrical tape. I don't notice it most of the time since my phone blocks the LED anyways when docked.
* A significant negative and quite surprising difference in the dock compared to the docks I had for my EVO 4G / Touch Pro and Mogul are that this dock only has one USB slot. So it either charges the battery and phone from a wall plug or it charges the battery and connects/charges the phone via your computer's USB port. My previous phone docks had 2 USB connectors, one for the battery and one for the phone. I haven't tried connecting this to my computer or charging an extra battery yet but I'm figuring trying to charge two things at the same time via one USB cable, especially when connected to a computer USB port would not be very efficient.
Update 12/09/2011: Argh, deal breaker, just got my Trexcell 3800mah Extended Battery, but because of the location of the battery contact on the battery and dock it won't fit, .
Killabee and talynone
that second black dock is the one I am interested in. my PRIMARY concern with docks that use the charging jack on the phone (whatever happened to dedicated dock "contacts" on phones Cheap SOB's)
is that I want the phone IMMOBILIZED while in the dock. ie I don't want to be able to TILT the phone forward while in the dock "stressing and breaking" the usb jack on the phone.
IE I want the dock to RESTRICT the movement of the phone to vertical only (insert remove dock connector type motion)
the first dock in this thread would NOT prevent the phone from tilting forward.
the second one I am not sure about. do those sides "wrap" around the edge of the phone enough to restrict its movement to a solid slide and NO forward slop?
Here is a video of what I mean. (its processing give it a few minutes to process)
http://www.youtube.com/watch?v=QhWtz5EU_Rg
nerys71,
I saw your video and can tell you that the phone in this dock is not restricted from tilting. So yes it will tilt while charging. I am talking about this dock:
http://www.amazon.com/gp/product/B005OTXKK4/ref=ox_sc_act_title_1?ie=UTF8&m=A3CZ5XR3PIAJMS
ahh pity. I assume you have it? does the phone protrude past the front "AT ALL" in that dock? IE it looks like it would be friendly to modding it with 2 "lips" on the front to prevent the phone tilting.
Yeah I have it. It doesn't pertrude at all. The phone sits flush.

CHARGING port help. Need a good seller

anyone out there know a place or website where i can get a new charging port flex cable that will actually work with out problems.
my original one didnt charge right unless i bent it backwards a little
i bought 3 off ebay and had problems with each
1st one off ebay had no sound
2nd one had no service
3rd one didnt charge at all.
the original one was a REV 1.0 connector and so were the others, so if anyone knows where to get one that will work with no problems let me know
THANK YOU
jhillyer253 said:
anyone out there know a place or website where i can get a new charging port flex cable that will actually work with out problems.
my original one didnt charge right unless i bent it backwards a little
i bought 3 off ebay and had problems with each
1st one off ebay had no sound
2nd one had no service
3rd one didnt charge at all.
the original one was a REV 1.0 connector and so were the others, so if anyone knows where to get one that will work with no problems let me know
THANK YOU
Click to expand...
Click to collapse
Try cnn.cn but i think you will find only the whole micro usb port and not the flex cable alone
I have tried 12 replacement parts from ebay for an i717 and they ALL have no service after putting them in. but the original one that doesn't charge still gets service fine...
edit: I can recommend http://www.parts4repair.com/. Worked like a charm
did you try the following:
http://forum.xda-developers.com/showthread.php?t=1948735
[/COLOR]
talonmike04 said:
I have tried 12 replacement parts from ebay for an i717 and they ALL have no service after putting them in. but the original one that doesn't charge still gets service fine...
Click to expand...
Click to collapse
well a i717 component in a n7000? version mismatch no?
Sent from my GT-N7000 using Tapatalk 2
Yes, the AT&T version and the International version have different radios, and the micro USB port is connected to them. They are NOT interchangeable.
i717 ≠ GT-N7000
Any tips anyone?
Hi, I just want to revive this thread rather than start a new one.
I am gonna swap my my usb charging port for a one I bought on eBay. Does anyone have any tips I should know about that you can tell me?
I'm going by this youtube video. this is all I got and of course I'm kinda scared.:crying:
Thanks. Will check back later.
Easy to do, but will cause other issues
Hi. I too have just brought a note with this problem.
The replacement is easy, remove battery cover, battery sim etc. Take out the screws, use something thin to pries the edge off. Its the lip below the screen level though. After that, 3 more screws for the bottom section, then take out the one screw in the thin motherboard piece. Slide out the old flex, slide in the new one, re assemble.
The biggest problem is that youll most likely lose 80 % of your reception from it. When the phone is open, try to see if there is any corrosion behind your USB port, if there is clean it and try it. I did that as im sending my ebay one back for a replacement, Now my old one seems to be working, but for how long, i dont know.
SalJam
I bought a battery charger and extra battery. I bought the brand Hyperion but I've heard there are better brands. Anyway, I don't charge my phone any more... I just swap batteries now. One is always on the charger and one in the phone. It works fantastically and further, the phone always has a charge. When I want to swap files I remove the card and put it in the PC. Works really good.
If you are on about the daughter board I got one of Amazon for£10 took less than 10 mins to fit and have had no problems. Came In OEM packaging
Any questions feel free to PM
Sent from BOX13.
---------- Post added at 10:20 PM ---------- Previous post was at 10:16 PM ----------
SalJam said:
Hi. I too have just brought a note with this problem.
The replacement is easy, remove battery cover, battery sim etc. Take out the screws, use something thin to pries the edge off. Its the lip below the screen level though. After that, 3 more screws for the bottom section, then take out the one screw in the thin motherboard piece. Slide out the old flex, slide in the new one, re assemble.
The biggest problem is that youll most likely lose 80 % of your reception from it. When the phone is open, try to see if there is any corrosion behind your USB port, if there is clean it and try it. I did that as im sending my ebay one back for a replacement, Now my old one seems to be working, but for how long, i dont know.
SalJam
Click to expand...
Click to collapse
It's 10 black screws on the back & 5 white to take there cover of over the daughter board. No need to undo a mother board screw whats this about losing 80%signal?
That's rubbish, Sir! Mine is on5 bars H+ and has been sincei did it. As there is a new mix. Too the sound is better, IMO
Sent from BOX13.
Bought mine off ebay worked 100%, signal is still the same, nothing happens to signal. But you have to buy the whole board. Mine didnt come with a wee microphone bit so i took off my old one, stuck the sticky bit within the square part and put the rubber part in the cover and screwed it on. Everything working fine.
Sent from my GT-N7000 using xda premium
My usb port is busted so am replacing that board too. However, I've bought two off ebay and both have had problems. First one fixed the charging issue but didn't give me any reception (well one bar now and then) and the second gave me signal but had a busted micro usb port. EBay can be so fustrating sometimes!!
howard bamber said:
If you are on about the daughter board I got one of Amazon for£10 took less than 10 mins to fit and have had no problems. Came In OEM packaging
Click to expand...
Click to collapse
I will have to try the ones on amazon instead.
fl4r3 said:
My usb port is busted so am replacing that board too. However, I've bought two off ebay and both have had problems. First one fixed the charging issue but didn't give me any reception (well one bar now and then) and the second gave me signal but had a busted micro usb port. EBay can be so fustrating sometimes!!
I will have to try the ones on amazon instead.
Click to expand...
Click to collapse
parts4repair has working ones lol.
Sent from my GT-N7000 using Tapatalk 2
baz77 said:
parts4repair has working ones lol.
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
Thanks, I'll try them out if my Amazon one turns out to be a dud (Which I have a feeling it will )
fl4r3 said:
Thanks, I'll try them out if my Amazon one turns out to be a dud (Which I have a feeling it will )
Click to expand...
Click to collapse
I have just fitted my 3rd replacement board and loose most of my signal after fitting it. My original board gives me full signal but intermittent charging. :crying:
Do all N7000 use the same board or does country intended for make a difference? My note is an International phone made for Hong Kong.
copperdawgnc said:
I have just fitted my 3rd replacement board and loose most of my signal after fitting it. My original board gives me full signal but intermittent charging. :crying:
Do all N7000 use the same board or does country intended for make a difference? My note is an International phone made for Hong Kong.
Click to expand...
Click to collapse
To be honest I still haven't got a perfect replacement yet but one that is at least functional (get werid noises during phone calls - not on my end but on whoever is calling me).
You do have to make sure you get the correct board though. If you look on the original board it should have some writing in gold near the top. Mine said Rev 1.0 so I got replacements which were rev 1.0 too. Apparently there are other revisions (although I didn't come across any others).
fl4r3 said:
To be honest I still haven't got a perfect replacement yet but one that is at least functional (get werid noises during phone calls - not on my end but on whoever is calling me).
You do have to make sure you get the correct board though. If you look on the original board it should have some writing in gold near the top. Mine said Rev 1.0 so I got replacements which were rev 1.0 too. Apparently there are other revisions (although I didn't come across any others).
Click to expand...
Click to collapse
mine is a version 1.00 see attached my original is on the top one of the replacements below
I did my replacement yesterday.
Got the part from this seller:
http://www.ebay.co.uk/itm/190821533955?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
And then followed this link on how to do it, took me 2 attempts as the 1st time I hadn't pushed one of the ribbon cables down and had no service. After pushing it in and putting it all back together it works again
http://www.youtube.com/watch?v=pD9R-YUT69Q
Ordered one from parts4repair, we'll see how that one works. The one I have now, works, but the signal level sucks.
p51d007 said:
Ordered one from parts4repair, we'll see how that one works. The one I have now, works, but the signal level sucks.
Click to expand...
Click to collapse
hi, did the flex from parts4repair work?
cheers
Yep, worked PERFECTLY. Improved signal performance in areas where I had little to no signal.
starfoo12 said:
hi, did the flex from parts4repair work?
cheers
Click to expand...
Click to collapse

Monster Watts Wireless Charging Kits for Gs3

Just found this as i was reading on the wireless charging the new S4 is supposed to get...
Apparently this company as of today is selling three options for wireless chargers for the gs3.
http://www.indiegogo.com/projects/samsung-galaxy-s3-gets-3-wireless-charging-options.
for 45$ ill give it a try and i get to keep my otterbox...
Hamspiced said:
Just found this as i was reading on the wireless charging the new S4 is supposed to get...
Apparently this company as of today is selling three options for wireless chargers for the gs3.
http://www.indiegogo.com/projects/samsung-galaxy-s3-gets-3-wireless-charging-options.
for 45$ ill give it a try and i get to keep my otterbox...
Click to expand...
Click to collapse
Very cool. I wonder what the charging pad looks like.
Also, while this will fit under your otterbox I don't know if it will actually charge it through it. Worth the $45 though!
for 45$ and a drop in solution i am willing to try and test it...
This looks like a damn good price tbh. $68 for a receiver and charger is cheaper than any qi combo that I know of currently.
The bonus is that it's also Qi technology so even if you change your s3 out, you should be able to get another phone that has qi tech in it or even modify that charging pad to work on other electronic devices (with some copper tape/wire)
mputtr said:
This looks like a damn good price tbh. $68 for a receiver and charger is cheaper than any qi combo that I know of currently.
The bonus is that it's also Qi technology so even if you change your s3 out, you should be able to get another phone that has qi tech in it or even modify that charging pad to work on other electronic devices (with some copper tape/wire)
Click to expand...
Click to collapse
Thats exactly what i was thinking.. The odd fact that i just so happend to find this today and apparently it just went live today i am pretty excited to snag it at this price.
But As im sure the capabilities to wirelessly charge are inevitably going to be included in future phones it isnt like this tech is likely going to be easily replaced. And it also seems like Samsung is going to abandon using our phones tech as wireless charging.. or at least thats what i gathered from thsi article..
http://www.theregister.co.uk/2013/03/11/samsung_s4/
the thing w/ samsung and wireless charging is that they really have no idea who the hell they're really going to back. Yes, Samsung co-founded A4WP, but they're also member of Qi's group as well.
To me, it just looks like they're sitting on the fence and waiting to see who will come out as the standard before going all in. I also don't think Samsung will build it into the phone itself due to its current ambivalence on the 2 standards and most likely leave it open like the s3 and note 2.
While the article talks about a4wp having a few cm of range, he also did not mention that a newer revision of Qi offers up to 4cm of range as well (last I checked).
I don't care much for too much range for wireless charging, just enough so that any non-ferrous case will charge regardless of thickness. I have a Qi set and it has so far worked with the ballisitc SG (although it Can get picky, but that's due to the fact that I also modified the charger to be at a 45 degree angle and the case's bottom lip [on the hard plastic side] curved up a little for no reason)
mputtr said:
the thing w/ samsung and wireless charging is that they really have no idea who the hell they're really going to back. Yes, Samsung co-founded A4WP, but they're also member of Qi's group as well.
To me, it just looks like they're sitting on the fence and waiting to see who will come out as the standard before going all in. I also don't think Samsung will build it into the phone itself due to its current ambivalence on the 2 standards and most likely leave it open like the s3 and note 2.
While the article talks about a4wp having a few cm of range, he also did not mention that a newer revision of Qi offers up to 4cm of range as well (last I checked).
I don't care much for too much range for wireless charging, just enough so that any non-ferrous case will charge regardless of thickness. I have a Qi set and it has so far worked with the ballisitc SG (although it Can get picky, but that's due to the fact that I also modified the charger to be at a 45 degree angle and the case's bottom lip [on the hard plastic side] curved up a little for no reason)
Click to expand...
Click to collapse
Right that much i understand...
I was holding out for the wireless charging where i didnt need to have it directly on the base. and every few months i search around for a viable option.
So far, since my free time is limited, this seems like the best all in one solution that doesnt require me to change my case, and its a good price.
Hamspiced said:
Right that much i understand...
I was holding out for the wireless charging where i didnt need to have it directly on the base. and every few months i search around for a viable option.
So far, since my free time is limited, this seems like the best all in one solution that doesnt require me to change my case, and its a good price.
Click to expand...
Click to collapse
in you case it seems to be a cheaper and more reliable solution imo.
all in all, it's a good find. although I should've ask if it affects nfc as well..
Sent from my GT-I9300 using xda app-developers app
The stealth one, and the one built into a battery cover can be found on a different site for only about $15.
this one comes with a charger as well.. which would cost 50-60 usd more. so it's a good deal.
Sent from my GT-I9300 using xda app-developers app
Well.. I bought mine for $47.90 with the charger and receiver, so if your willing to spend just another $2 then you can get that with less of the wait.
that's great. any link for others who might be interested?
Sent from my GT-I9300 using xda app-developers app
Hm.. I like how there is radio silence as soon as there is a mention of link to provide proof.....
I wonder if the smart one works with those thin protective cases?
mputtr said:
that's great. any link for others who might be interested?
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
What do you mean link for others? i ordered mine the day i posted.
Hamspiced said:
What do you mean link for others? i ordered mine the day i posted.
Click to expand...
Click to collapse
That was for Tenchuboy, not you.
He claimed he got a set that was cheaper and all that, so I asked a link so he can prove it. So far, complete silence from him.
OOOhhhhhhh....
i got it. i know i could make a set with the palm pixie stuff, i priced it out on amazon and total with a charging dock its like 20$... but i dont have the time to. im only actually home about 3 days a month. id rather be lazy..
Just an FYI i got my wireless charging kit from this company and it works great. Its a small device that attaches to the back of the stock battery. Its very small and it fits perfectly, very small buldge from the device but the back case fits on fine and my otterbox fits it perfectly.
the best part, it works with the stock otterbox. there were no issues with wireless charging whatsoever.
How is this one any different than any of the other wireless IQ receiver pads & chargers for the s3?
Sent from my SAMSUNG-SGH-I747
That it works with all variants, doesnt require you to change out your battery door, although they offer a solution for it, and its pad and reciever for 40$

AT&T warranty replacements with no wireless charging

I got a Qi sticker and some pucks from Amazon for my original G4, and the wireless charging worked fine. Then it bootlooped, so I got a replacement (they sent me a refurb or course) and on the new phone, wireless charging just refuses to work at all. I called back to complain about that and they sent me another refurb, and wireless charging isn't working on this one either. I haven't changed anything at all but the phone itself. They had me keep my back with the sticker still intact, and of course my same chargers. Anyone else have this issue? I guess I'll call them back again, I'm just tired of fighting with them for yet another refurb phone. The only thing I noticed is a weird clicking noise when I put the phone on the puck. I'm not sure if it did that before or not.
Are there wireless charging contacts on the phone main body? Some OEM versions don't have wireless charging.
If the contacts are there, you could try slipping some paper or electrical tape under the contact pad on the back to raise it a little bit to make better contact. If that does not work maybe the sticker needs to be repositioned to align the contacts. Look carefully at the contact pads on the back - you should be able to see where the metal phone contacts are pressing against it. Everything has to be positioned just right to get both charging and NFC to work...
MikeyTG said:
Are there wireless charging contacts on the phone main body? Some OEM versions don't have wireless charging.
If the contacts are there, you could try slipping some paper or electrical tape under the contact pad on the back to raise it a little bit to make better contact. If that does not work maybe the sticker needs to be repositioned to align the contacts. Look carefully at the contact pads on the back - you should be able to see where the metal phone contacts are pressing against it. Everything has to be positioned just right to get both charging and NFC to work...
Click to expand...
Click to collapse
Yes, they're there. They were there on the first phone and the 2 after. I've tried manipulating the Qi sticker, but the exact same sticker worked fine on the first phone, and then not at all on the next 2. I might try a new sticker, but it's just strange.
sinala said:
I got a Qi sticker and some pucks from Amazon for my original G4, and the wireless charging worked fine. Then it bootlooped, so I got a replacement (they sent me a refurb or course) and on the new phone, wireless charging just refuses to work at all. I called back to complain about that and they sent me another refurb, and wireless charging isn't working on this one either. I haven't changed anything at all but the phone itself. They had me keep my back with the sticker still intact, and of course my same chargers. Anyone else have this issue? I guess I'll call them back again, I'm just tired of fighting with them for yet another refurb phone. The only thing I noticed is a weird clicking noise when I put the phone on the puck. I'm not sure if it did that before or not.
Click to expand...
Click to collapse
I've got a similar issue, but with mine, they changed the mainboard and returned it. Is yours a 602 serial # device or are the refurb units which they sent you 5xx? If 602, I'm curious if part of the "fix" involved completely removing the wireless charging capability. I even tried peeling off the Qi sticker and carefully positioning it over the contacts, then putting the cover back on, just in case maybe it was out of alignment - crazy thought since it worked fine before the bootloop/warranty issue. But that made no difference.
sleepy_76 said:
I've got a similar issue, but with mine, they changed the mainboard and returned it. Is yours a 602 serial # device or are the refurb units which they sent you 5xx? If 602, I'm curious if part of the "fix" involved completely removing the wireless charging capability. I even tried peeling off the Qi sticker and carefully positioning it over the contacts, then putting the cover back on, just in case maybe it was out of alignment - crazy thought since it worked fine before the bootloop/warranty issue. But that made no difference.
Click to expand...
Click to collapse
Mine's a 601 serial. I contacted LG directly and they just said "Oh that device doesn't do Qi you need to get the other one" but could never answer why the other one worked fine..

Categories

Resources