This a smple guide to
Change the CN sku to WW sku and also to flash prerooted firmware....
There are 3 methods to flash firmware:
a. Fastboot method - using ADB cmd in fastboot mode - described below - most common and definitive
b. Sideload ADB method - into recovery and using adb cmd method - incases where the above method is at fault or difficult
c. OTA method - by flashing or by copying in the phone storage and allowing it to perform like OTA update
FASTBOOT method:
Pre rooted firmware version used is PREROOTED 2.15.40.10 by the gret and devoted Shakalaca
Step by step instructions to flash firmwares in Zenfone 2:
Note: tested and verified in ZE551ml 32gb/4gb 1.8ghz model.
Thanks to
1. Shakalaca for the great effort and work for firmware
2. Vivix – for making it simple
3. Chinaphonearena for the support and files
4. All XDians for support and help
Requirements:
1. Laptop/PC with windows
2. Zenfone 2 Z00A model
3. Downloaded files – 4 files of app 1.3gb data volume – link given below
4. Micro usb cable to connect to pc/ laptop
5. TIME & PATIENTS
Steps:
In Computer:
a. Download Flashtools.zip from here.. https://mega.co.nz/#!2VU1RS6J!a7bgeAbyRQpECFdLtm-RDNKNpybhWGT7xUu5TXqvxXk
b. Download recovery.img from here https://mega.co.nz/#!DdlChA7B!x-Tnaf_6fCo-3xSWRFIAZCr6BGGledQcLiw7Fk7WvuM
c. Download boot.img from here… https://mega.co.nz/#!GF1EhCRI!s-RKUTsMwwcxcmRNrr8oEBk2IeDYIY4D1Nr7HUP-3rI
d. Download system.img in system.rar file from here…https://mega.co.nz/#!CN9jDLhY!rKB0ekicCXeo5YMMVkSxW1Kt_ty_b9k3YDyTRmw2bTg
System.rar ----- md5 -------b3574fffb1fa135e237b483522e269ac
System.img ------ md5-------d92ddf4030ae6cef081ac732f668c5f7
Steps:
1. In PC/Laptop: Unzip the flashtools.zip files in a separate new folder.. as below
https://mega.co.nz/#!vV0ghLYb!h0kMVg-S9RAM2a-uEkeBcfLemmDlXYClfG40NZ4PHHM
2. COPY the files recovery.img and boot.img into this same folder… flashtools
3. Unzip the system.rar file and place the system.img file into the same folder… flashtools
4. At this stage, the folder should have all the files of flashtools along with boot.img, recovery.img and system.img
5. In zenfone
a. Switch off the phone and remove the SD card if any ( SD card is removed for prevention of SD card data and is purely OPTIONAL)
b. Boot into fastboot mode by following the sequence…..
- Switched off phone HOLD VOL UP button first followed by POWER button
- WAIT till you feel the VIBRATION, then leave ( remove the finger) the power button and continue holding the volume up button [ do not leave the vol up button – if you leave it will boot into android as normal]
- Continue holding the vol up button until you see 2/3 flickers and FASTBOOT menu
- On seeing the fastboot menu, release the vol up button and place it near the laptop/computer
- CONNECT the data cable and wait until it installs the required files ( Similar to inserting a new USB flash drive)
- Once done CONNECTED zenfone 2 Is ready for flashing
6. In PC / Laptop
a. Open the folder flashtools
b. Press shift + right click to open the dialogue drop box…
c. Select “open command Window here”
d. Once clicked will open the cmd window like this
https://mega.co.nz/#!7QkEnJ5T!aRkWi6QSvSbeCTtTvoh7Sgb2CG9-fgqzxkTqS7szMbY
e. Now start typing
fastboot flash recovery recovery.img
wait… look into the phone screen… it will say completed
fastboot flash boot boot.img
wait…. Look into the phone screen … once completed
fastboot flash system system.img
wait… it will happen in parts… maybe 5/6 parts….. once completed …. Done
DISCONNECT the phone from PC and press power button… it will switch on and start to boot into new firmware…. Until you wait… Have a CUP of TEA… and enjoy ur Zenfone 2
HIT THANKS if this was useful for you....
Update
How to update the OTA firmware - MANUAL method
Note: always download relevant boot.img and the update.img file
For those who need ASUS stock firmware...
download the update firmware relevant to your SKU and flash as above...
Flash only boot.img and recovery.img and in place for system.img ----- flash update.img file that you have downloaded.
For future uses
Beginners with doubts and questions can interact here...
I will be updating the system.img file as and when we get the prerooted files released in the WEB....
Can I do this on my phone which has 2.13.40.13? Sorry for the question, am an old beginner
Sent from my ASUS_Z00AD using XDA Free mobile app
Hi
OK for upgrade but what about downgrade ? Like coming back from .22 to .20...
This worked for me. Had some bumps with the connection to the pc. First tried on Vista but won't recognize the phone. When I tried on Windows 8.1 finally connected. A word about the flashing of the system image. You really have to WAIT. At first I thought something went wrong until it started after about 5 minutes or so, and yes in parts because of the big file. Many many thanks for your help. Last question: will the phone now accept OTA updates? More power to XDA!
Sent from my ASUS_Z00AD using XDA Free mobile app
---------- Post added at 06:47 AM ---------- Previous post was at 06:43 AM ----------
Wow! My phone "flies" now. I love you guys!
Sent from my ASUS_Z00AD using XDA Free mobile app
OK I am desperate I have tried this guide and several others. I follow it to the letter and everything works as described but all I get is a bootloop. Any help would be very much appreciated. When I go into the recovery I see for a split second - installing system then I get an error. On normal boot I just get the bootloop.
Thanks any help would be very much appreciated.
Windows version for this
Have Windows 10, ASUS laptop. When connect Zenfone 2 to it, it shows up on the laptop as a CD drive. I know this can't be right. Is Win10 missing drivers for this or something?
Related
SOLVED SOLVED SOLVED
Hi All
Is there anyone willing to help me recover my phone (presently stuck on logo screen). I've looked at various solutions posted on different forums but I just get confused.
So what I would like is idiots guide on how to do it, including how to write the commands codes so I can flash the updated CWM rom. Tried to work it out but everything I've tried keeps failing and I desperate to get my phone working again.
Please please help
Tell us what you have done so far m8 and the reason for it being stuck. At a guess did you flash the boot.img when installing a Rom?
To install or update recovery, go here and follow the instructions on the second part "Installing A Recovery" Just follow the steps its pretty easy.
http://forum.xda-developers.com/showthread.php?t=1592355
Flash the appropriate boot.IMG for your rom
Sent from my HTC One X using Tapatalk 2
hmmm
Thats what i've trying to do but I can't seem to work out what cmd codes I need to get it to work. All I get is:
'Downloads\OneXRoot' is not recognized as an internal or external command
operable program or batch file.
This error message on everything I try to do incuding flashboot, flashboot recovery etc
Tried micks solution and all it did was open Nero gggrrrrrr
And yes I did flash a boot image but i'm trying to get the updated one onto my phone but because my battery won't charge it proving to be a nightmare
From the link I posted do as the guide says re making a folder called fastboot on C: and then download the files and extract them to fastboot. Replace the end of the guide with instructions for flashing a boot image. The boot.img is usually in the zip of the rom. So you need to extract the boot.img and place it in your C:\fastboot folder
It should go something like this. Use C:\ not Downloads\OneXRoot
1. Download These Fastboot Files
2. Make a new folder on your C: drive called fastboot.
3. Extract The Zip downloaded in step 1 to the new folder
4. The Official Version of CWM has been released and is now capable of flashing all roms, you can grab it HERE
5. download the custom recovery and save it in the same folder as you did the fastboot files
6. Power Phone Off by Holding power button for 10 secs
7. select Fastboot with volume + or - then press power
8. plug your phone into your PC and open a Command Prompt.
(windows XP - Click Start > Run > type CMD in box then press OK
(Windows 7 - Click Start > type CMD in search box then press Enter)
9. cd to your fastboot files folder cd c:\fastboot
10. Then enter fastboot flash boot boot.img and hit enter
11. fastboot erase cache is recommended if you have booting issues
reboot
ignore steps 4 and 5, copy and paste from above link
Going to buy a new phone
Followed your instruction to the letter but it failed to work. I think the problem is with my computer not recognising fastboot and the solution also failed. So I think i'm just going to buy a new phone and thanks for all your help
No need to buy a new phone, stick with it, you'll get there
Maybe give this a try. It does everything for you
http://forum.xda-developers.com/showthread.php?t=1734365
Nice
Thanks thats a solution that will work once I find away to charge my battery. You have been a legend.
Cant you just put it in to recovery or leave it on the hboot screen, then plug in to a wall charger?
In Q&A, find the topic "flashing boot.img hoooooooow????" Or something, and at second side, u have my guide to flash boot.img files. Hope it works.
Sent from my HTC One X using xda app-developers app
hello dear sir
i have ASUS Fonepad 7 FE170CG
so i download
all firmware from here
http://www.asus.com/Tablets_Mobile/ASUS_Fonepad_7_FE170CG/HelpDesk_Download/
but can not know how to flsah my device
plz help thanx
any one tell me how to flash i put firmware zip inside sd card and press sd download but its said cant found firmware img
nokia alkng said:
any one tell me how to flash i put firmware zip inside sd card and press sd download but its said cant found firmware img
Click to expand...
Click to collapse
Just place the downloaded firmware (UL-xxx.zip) into root folder on your internal storage or external sdcard. The system will automatically recognize it and asking do you want to flash it.
Just make sure you had the correct regional firmware (mine was WW)
edors said:
Just place the downloaded firmware (UL-xxx.zip) into root folder on your internal storage or external sdcard. The system will automatically recognize it and asking do you want to flash it.
Just make sure you had the correct regional firmware (mine was WW)
Click to expand...
Click to collapse
mine is also WW for model no-K012
BT i want to know as how will i flash if the device doesnt turns i.e stuck at logo like problem.....
is there any method if so please elaborate
vks.sud said:
mine is also WW for model no-K012
BT i want to know as how will i flash if the device doesnt turns i.e stuck at logo like problem.....
is there any method if so please elaborate
Click to expand...
Click to collapse
Rename your downloaded firmware to K012_sdupdate.zip then copy to your MICROSD. Now you just have to go into droidboot mode.
Follow the step below to go into droidboot. (Start by turn off your device).
1. If you had never update to kitkat before, go into droidboot by holding VOL DOWN + POWER until droidboot menu is present.
2. If you have update to kitkat before (or currently on kitkat), boot into droidboot by holding VOL UP + POWER until menu is present.
Next step depend on menu that appear on your droidboot menu:
1. If you had SD UPDATE option presented on the MOST BELOW option, go on and select it. (Beware, you should choose SD UPDATE not SD DOWNLOAD)
2. If your menu doesnt show SD UPDATE, then you had to choose RECOVERY.
I think thats all to do, your device must have start the update process by now.
CMIIW
But there is no recovery mode in this device like cwm or twrp..............
have a look.....
in the video below i have started in recovery without puting the firmware archieve in sdcard....will it surely work...
and one thing more is there ant way to install cwm or twrp or any other recovery on this device......
Flash fonepad firmware
It's very easy. Just put the downloaded zip file in the root of you internal memory and you will see a notification which says it has detected a new update file. Tap on it and install.
Good luck
Ali Erfani said:
It's very easy. Just put the downloaded zip file in the root of you internal memory and you will see a notification which says it has detected a new update file. Tap on it and install.
Good luck
Click to expand...
Click to collapse
but this can be done when the device starts what if it is in bootloop or hang on boot logo
vks.sud said:
but this can be done when the device starts what if it is in bootloop or hang on boot logo
Click to expand...
Click to collapse
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
what do u mean by choose the Recovery (if you have updated to 4.4.2) ..there is no custom recovery for this tablet???
vks.sud said:
what do u mean by choose the Recovery (if you have updated to 4.4.2) ..there is no custom recovery for this tablet???
Click to expand...
Click to collapse
I mean before you had this problem. The fastboot menu is different for Android 4.3 and 4.4
I don't know if there is a custom ROM for this tablet or not!!!
Help! I cant access my fastboot, how can flash rom? Or is there a way to flash flashboot? Thanks
Everyime i turn on my device its just usb icon them turns off.
Thank You!
Your procedure worked perfectly.
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
some thing wrong
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
Hi, I Do All The Thing You Say. Every Thing was Ok And Done but when i select recovery and tablet gets reboot and starting to install the rom... until 70% it take error and then back to a screen that shows a android picture. and do not complete the installation :/ whats wrong hear?
by the way... ما هم زبانیم
برا این انگلیسی نوشتم تا بقیه هم که به این مشکل خوردن ببینن نتیجه چیه :/
and one more thing SKU of rom and tablet is same and the external memory card is 8GB Class 10
alirezajalilii said:
Hi, I Do All The Thing You Say. Every Thing was Ok And Done but when i select recovery and tablet gets reboot and starting to install the rom... until 70% it take error and then back to a screen that shows a android picture. and do not complete the installation :/ whats wrong hear?
by the way... ما هم زبانیم
برا این انگلیسی نوشتم تا بقیه هم که به این مشکل خوردن ببینن نتیجه چیه :/
and one more thing SKU of rom and tablet is same and the external memory card is 8GB Class 10
Click to expand...
Click to collapse
Well that happened to me and i managed to fix my tablet. NOTE: MAKE SURE YOUR DEVICE IS MODEL NO. K012 FE170CG
BEFORE YOU CONTINUE
1. Download ADB and Fastboot : [TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2
2. Install ADB drivers : Intel Android USB Drivers
3.Download Previous Firmware from Asus support site.
4. Download this for temporary tethered cwm
ACTUAL PROCEDURE
1. copy the firmware (.zip) to an external sd card
2. Extract downloaded recovery.rar
3. Put your device in Droidboot mode by holding both power button and vol down while device is turned off.
4. Connect device to computer. Open cmd and type "fastboot device" to verify.
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
6. Some stuff will appear after that. Dont do anything. In a few moments CWM will load.
7.Next part is pretty self explanatory. use volume keys to go up and down and press power to select option. choose install zip. in the next menu choose install from external sd card*. Choose the zip file you downloaded from Asus website, if installation fails download another version from the support website.
FISRT BOOT MIGHT TAKE SOME TIME.
* I dont remember the exact wordings.
------Hit thanks if this helped you------------
HELP
neondragon1909 said:
Well that happened to me and i managed to fix my tablet. NOTE: MAKE SURE YOUR DEVICE IS MODEL NO. K012 FE170CG
BEFORE YOU CONTINUE
1. Download ADB and Fastboot : [TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2
2. Install ADB drivers : Intel Android USB Drivers
3.Download Previous Firmware from Asus support site.
4. Download this for temporary tethered cwm
ACTUAL PROCEDURE
1. copy the firmware (.zip) to an external sd card
2. Extract downloaded recovery.rar
3. Put your device in Droidboot mode by holding both power button and vol down while device is turned off.
4. Connect device to computer. Open cmd and type "fastboot device" to verify.
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
6. Some stuff will appear after that. Dont do anything. In a few moments CWM will load.
7.Next part is pretty self explanatory. use volume keys to go up and down and press power to select option. choose install zip. in the next menu choose install from external sd card*. Choose the zip file you downloaded from Asus website, if installation fails download another version from the support website.
FISRT BOOT MIGHT TAKE SOME TIME.
* I dont remember the exact wordings.
------Hit thanks if this helped you------------
Click to expand...
Click to collapse
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
What can i do if the device is unknown and fail to communicate with device?I follow the steps but ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2 cannot be install,0 files copied when installing adb and fastboot ?HELP!
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img)
I cannot find these three .img files.Where can i download them?
Hello, do you knw which rom without all the asus bloatware I could install ?
My fonepad 7 is rooted but when I uninstall the shiiite asus programs they come back on restart.
Please help <3
I did the procedure and now is with this screen
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
arthurmdiniz said:
i did the procedure and now is with this screen
Click to expand...
Click to collapse
where can i dl the three .img help!!!!!!!!!!
NOTE: FLASHING KITKAT AFTER UPDATING TO LOLLIPOP (i.e. DOWNGRADING) IS NOT SUPPORTED. YOUR DEVICE WILL GET HARD BRICKED IF YOU ATTEMPT TO DO SO
Hello Yureka Users,
The factory image (fastboot flashable zip) and debuggable boot image are now available on Cyanogen Support page.
For the convenience of the users, we have also created a package containing required tools for flashing and a one-click flashing script.
These flash tools are available for download here - ( Windows - Linux - Mac )
There are detailed step by step instructions written for each OS ( Windows - Linux - Mac )
Flashing the whole package will get your phone back to factory state and WILL WIPE all data on your phone. (Except any data on the external microSD card, if you have one).
As newer updates come out in coming months, the support page will be updated with newer factory images.
In the spirit of the community, the flash tools package, and the script are up on github, and we welcome anyone who wants to improve on the flashing scripts/tools.
Cheers,
Team YU
Steps to flash factory image (WINDOWS)
Download the factory image fastboot package from Here
Extract the contents of the fastboot package into a folder.
Download this flashing tools package from here
Extract the contents of the flashing tools zip into the same folder
To make sure, check that system.img, boot.img etc files are in the same folder as flash-all.bat, fastboot.exe etc
Connect your phone in fastboot mode, steps for which are : -
a. Power off your phone
b. Press and hold the Volume Up key
c. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
d. You can let go off the Volume Up key when Fastboot Mode is displayed on the screen
Run flash-all.bat by double clicking on it.
A command window will open and flashing procedure will start
DO NOT disconnect the device during flashing procedure
The command window will close after the flashing process is over.
Disconnect the USB cable, and boot the phone normally by long pressing the Power button.
=========================================================================================================
Steps to flash factory image (LINUX)
Download the factory image fastboot package from here
Extract the contents of the fastboot package into a folder.
Download this flashing tools package from here
Extract the contents of the flashing tools zip into the same folder
To make sure, check that system.img, boot.img etc files are in the same folder as flash-all.sh, fastboot.exe etc
Connect your phone in fastboot mode, steps for which are : -
a. Power off your phone
b. Press and hold the Volume Up key
c. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
d. You can let go off the Volume Up key when Fastboot Mode is displayed on the screen
Run "flash-all" by double clicking on it. (Or you can run the flash-all.sh script from a terminal)
A command window will open and flashing procedure will start
DO NOT disconnect the device during flashing procedure
The command window will close after the flashing process is over.
Disconnect the USB cable, and boot the phone normally by long pressing the Power button.
=========================================================================================================
Steps to flash factory image (MAC)
Download the factory image fastboot package from Here
Extract the contents of the fastboot package into a folder.
Download this flashing tools package from here
Extract the contents of the flashing tools zip into the same folder
To make sure, check that system.img, boot.img etc files are in the same folder as flash-all.command, fastboot.exe etc
Connect your phone in fastboot mode, steps for which are : -
a. Power off your phone
b. Press and hold the Volume Up key
c. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
d. You can let go off the Volume Up key when Fastboot Mode is displayed on the screen
Run flash-all.command by double clicking on it.
A command window will open and flashing procedure will start
DO NOT disconnect the device during flashing procedure
The command window will close after the flashing process is over.
Disconnect the USB cable, and boot the phone normally by long pressing the Power button.
Add Images
Nice Post Dude.
But u should atleast add screenshots to it and/ or a video link for it on how to do
help my phone bricked
After flashing custom ROM miui on YUREKA phone is completely dead ..only
red light is shown when connected to PC without battery ...with battery phone doesn't boot up ..
no fast boot
no adb
is there any tool to flash i have stock
also have backup
plz reply fast ...phone bricked
ravurambo said:
After flashing custom ROM miui on YUREKA phone is completely dead ..only
red light is shown when connected to PC without battery ...with battery phone doesn't boot up ..
no fast boot
no adb
is there any tool to flash i have stock
also have backup
plz reply fast ...phone bricked
Click to expand...
Click to collapse
same here. let me know if you find any solution
championswimmer said:
Hello Yureka Users,
The factory image (fastboot flashable zip) and debuggable boot image are now available on Cyanogen Support page.
For the convenience of the users, we have also created a package containing required tools for flashing and a one-click flashing script.
These flash tools are available for download here - ( Windows - Linux - Mac )
There are detailed step by step instructions written for each OS ( Windows - Linux - Mac )
Flashing the whole package will get your phone back to factory state and WILL WIPE all data on your phone. (Except any data on the external microSD card, if you have one).
As newer updates come out in coming months, the support page will be updated with newer factory images.
In the spirit of the community, the flash tools package, and the script are up on github, and we welcome anyone who wants to improve on the flashing scripts/tools.
Cheers,
Team YU
Click to expand...
Click to collapse
if i will flash this. will i revert back to stock recovery and locked bootloader ?
i come to know that lolipop update will be flashable only on stock recovery. is it true ?
does this method apply to fastboot files of cm12 as well?
Cause many users who directly flashed this cm12 fastboot files are now having hard bricked devices
championswimmer said:
Steps to flash factory image (WINDOWS)
Download the factory image fastboot package from Here
Extract the contents of the fastboot package into a folder.
Download this flashing tools package from here
Extract the contents of the flashing tools zip into the same folder
To make sure, check that system.img, boot.img etc files are in the same folder as flash-all.bat, fastboot.exe etc
Connect your phone in fastboot mode, steps for which are : -
a. Power off your phone
b. Press and hold the Volume Up key
c. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
d. You can let go off the Volume Up key when Fastboot Mode is displayed on the screen
Run flash-all.bat by double clicking on it.
A command window will open and flashing procedure will start
DO NOT disconnect the device during flashing procedure
The command window will close after the flashing process is over.
Disconnect the USB cable, and boot the phone normally by long pressing the Power button.
=========================================================================================================
Steps to flash factory image (LINUX)
Download the factory image fastboot package from here
Extract the contents of the fastboot package into a folder.
Download this flashing tools package from here
Extract the contents of the flashing tools zip into the same folder
To make sure, check that system.img, boot.img etc files are in the same folder as flash-all.sh, fastboot.exe etc
Connect your phone in fastboot mode, steps for which are : -
a. Power off your phone
b. Press and hold the Volume Up key
c. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
d. You can let go off the Volume Up key when Fastboot Mode is displayed on the screen
Run "flash-all" by double clicking on it. (Or you can run the flash-all.sh script from a terminal)
A command window will open and flashing procedure will start
DO NOT disconnect the device during flashing procedure
The command window will close after the flashing process is over.
Disconnect the USB cable, and boot the phone normally by long pressing the Power button.
=========================================================================================================
Steps to flash factory image (MAC)
Download the factory image fastboot package from Here
Extract the contents of the fastboot package into a folder.
Download this flashing tools package from here
Extract the contents of the flashing tools zip into the same folder
To make sure, check that system.img, boot.img etc files are in the same folder as flash-all.command, fastboot.exe etc
Connect your phone in fastboot mode, steps for which are : -
a. Power off your phone
b. Press and hold the Volume Up key
c. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
d. You can let go off the Volume Up key when Fastboot Mode is displayed on the screen
Run flash-all.command by double clicking on it.
A command window will open and flashing procedure will start
DO NOT disconnect the device during flashing procedure
The command window will close after the flashing process is over.
Disconnect the USB cable, and boot the phone normally by long pressing the Power button.
Click to expand...
Click to collapse
@championswimmer Does this factory images contain twrp recovery and rooting? This is for 64 bit ryt? I am newbie for yu world coz i was a xperia user...plz help me I want to unlock my bootloader and root my yuereka...I am on cm 12 official installed via cm recovery...
Yureka hard brick
ravurambo said:
After flashing custom ROM miui on YUREKA phone is completely dead ..only
red light is shown when connected to PC without battery ...with battery phone doesn't boot up ..
no fast boot
no adb
is there any tool to flash i have stock
also have backup
plz reply fast ...phone bricked
Click to expand...
Click to collapse
Is Now ur phone ok...?
Kapiljhajhria said:
same here. let me know if you find any solution
Click to expand...
Click to collapse
facing the same problem after flashing the stock rom with fastboot only red led notification with out battery help me some one
kewalj2646 said:
facing the same problem after flashing the stock rom with fastboot only red led notification with out battery help me some one
Click to expand...
Click to collapse
Most probably your device is bricked. But no worried since its YU device you can get replacement. just call their CC.
Mine was bricked as well so i asked for replacement and they gave me one.
Pls post the Linux flashtools link as it is not working.
my yu yureka is also hard bricked no yu logo, plz if nayone can give me quick solution
Does this steps works or not ??
installation aborted
I got cm12 update few days ago.BT I can't install it
Check it out and solve it. https://youtu.be/BUVVj2aE5Jw
The link to get flash tool is not working, please provide the alternative link
any1 figured out the red light and hard bricked mine is also bricked since dec!
ashish_zarekar said:
if i will flash this. will i revert back to stock recovery and locked bootloader ?
i come to know that lolipop update will be flashable only on stock recovery. is it true ?
Click to expand...
Click to collapse
i am flashing cm12.1 after i got into bootloop. it has been very long since the flash has started. idk what to do. pls help immediately
Allen_Abraham said:
i am flashing cm12.1 after i got into bootloop. it has been very long since the flash has started. idk what to do. pls help immediately
Click to expand...
Click to collapse
do you still need help?
what is your problem
ashish_zarekar said:
do you still need help?
what is your problem
Click to expand...
Click to collapse
No bro, I fixed it. I just relaxed the ROM. ?
[RECOVERIES & ROOT] Yureka custom recoveries & Root without Changing Stock Recovery
Note : This tutorial is for YU Yureka based on CM11 (KK 4.4.4) 32bit architecture
and
do it on your own risk, I will not be responsible if you brick your phone
Here is the detailed guide and collection of stock and all custom recoveries for YU Yureka and detailed guide to Root YU Yureka without changing Stock Recovery
Requirements
1. YU Yureka (obviously) with USB Data cable
2. PC / Laptop (Having Windows installed at least Windows 7 or above)
3. Drivers (Windows Automatically detect and install the required drivers)
4. ADB & Fastboot binary package that can be downloaded from XDA 15 seconds ADB Installer v1.4.2']http://forum.xda-developers.com/showthread.php?t=2588979
5. Custom Recovery (Anyone in which you are interested CWM, PhiZ, TWRP)
6. Latest SuperSU.zip file to root your phone
Warning: This process may delete all data stored in internal storage so better backup all the files stored in internal storage.
Step One
Enable USB Debugging on your device you can just follow these steps:
Go to Settings> About phone and keep taping on build number at least 7 times or till it appears "You are a developer now",
Now again go to settings>developer option (only after the previous step it will be enabled)> check/select USB debugging.
Step Two
Unlock your bootloader to flash custom recovery and root.
Here is the process
1. Download the adb & fastboot binary package and install it.
2. Put your phone into FASTBOOT mode by following anyone from below methods :
Method 1 (easiest)
-------------------
a. Power down phone
b. Plug USB cable to your PC
c. Press and hold Vol Up button and plug other end of USB to your device, soon you will see the fastboot screen.
(or without plugging USB Cable, Press and Hold Power and Vol Up buttons simultaneously, until you see the screen
"FASTBOOT MODE"
Method 2
---------
a. While your phone is Power On, plug USB Data Cable with PC and Phone (USB Debuging must be Enable)
b. Open Command Prompt on your PC (with Administartor rights) and type the following command
adb -s 0x1ebf devices
You will get results something like that :
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
3a289c2 device
*Note : If you get "authorization message" then look on your mobile screen and authorize your PC and run the command again.
c. Now note down the device no. (for e.g. in above "3a289c2") and type the following command
adb -s 3a289c2 reboot bootloader
[*Note replace the device id with your id (here 3a289c2), that you got in last command]
Now your phone must be booted into fastboot mode. A screen with "Fastboot Mode" should be appear on your phone.
3. Device drivers will get installed by windows (please wait for the driver installation to complete)
4. After driver installation is done go to the folder where you have extracted the package
5. Now open elevated DOS command prompt (terminal) on your PC and go into the same folder where you saved the recovery file
(*Note : to start command prompt directly from desired folder, while holding the Shift Key Right Click on folder and select start "open command window here")
6. Type the following command to check if the device was detected in fastboot mode
fastboot -i 0x1ebf devices
you should get output like : 2a25d00 fastboot
if you don't get similar output it means that the drivers weren't correctly installed or the device wasn't connected properly
7. If the output is similar to above then run the following command:
fastboot -i 0x1ebf oem unlock
you should get output something like :
.....
OKAY [ 0.003s]
finished. total time: 0.004s
8. Now your bootloader is now unlocked.
*Note : if you want to re-lock your bootloader again (for warranty on any other reason), again boot into fastboot mode and this time type the following command and enter
fastboot -i 0x1ebf oem lock
Step Three
Boot your phone into recovery (temporarily or permanently) and root your phone
1. Download SuperSU.zip and put it on root of your internal or external SD card
2. To load custom recovery (CWM / TWRP / PhiZ) temporarily, now type this command in terminal :
fastboot -i 0x1ebf boot CWM_6.0.5.1_recovery-yu.img
*Note 1 : if you want to flash the custom recovery permanently then us the following command
fastboot -i 0x1ebf flash CWM_6.0.5.1_recovery-yu.img
*Note 2 : if your download custom recovery is named differently (here CWM_6.0.5.1_recovery-yu.img) then while writing the above commands you need to put the name of the recovery same as as your saved file name (anyone CWM / Phiz / TWRP)
3. Done ! You loaded custom recovery temporarily, if command used with "boot" hence to root your phone, proceed to next section (step 5).
or
If you flashed recovery permanently, using command with "flash" then boot your phone into recovery. To do so, you have Two options
i) type the following command and press enter : adb -s 3a289c2 reboot recovery
or
ii) power off your phone, after then press and hold "Vol up+ Vol down + Power" buttons simultaneously to boot into custom recovery.
Now to root your phone proceed with next section (step 5).
Root your phone
5. To gain root access, flash SuperSu.zip that is stored on your internal or external SD card (in step 1)
6. Choose reboot phone and enjoy rooted phone with stock or custom recovery !
Special Note 1
I didn't tested, but came to know that root doesn't effect OTA update on Yureka.
You can get OTA updates with root but after the OTA update is flashed you will loose root access. To keep it or to avoid this please go to System Settings -> Developer Options -> UNTICK -"Update CM Recovery" (update recovery while installing system updates)
Even though if someone want to go back to Stock recovery, then download the official stock recovery (link no. 6 above) and flash it using command in fastboot mode (second command in step 2 under head "STEP THREE")
Downloads
1. 15 seconds ADB Installer v1.4.2 http://forum.xda-developers.com/showthread.php?t=2588979
2. Super SU latest v2.46 http://download.chainfire.eu/696/SuperSU/UPDATE-SuperSU-v2.46.zip
3. CWM 6.0.5.1 https://s.basketbuild.com/devs/vishal_android_freak/yu/yureka
OR http://d-h.st/ElAe
4. PhilZTouch 6.59 based on CWM v6.0.5.1 http://www.androiddevs.net/downloads/
OR http://d-h.st/UqWK
5. TWRP 2.8.5.0 http://techerrata.com/browse/twrp2/tomato
OR https://www.androidfilehost.com/?fid=95916177934528156
OR http://d-h.st/5wDD
6. YU Yureka Official Stock Recovery http://d-h.st/tQ1k
Special Note 2
Without the vendor id, phone will not get detected in fastboot mode.
Like if you want to check fastboot type this :
fastboot -i 0x1ebf devices
therefore, always add "i -0x1ebf" after fastboot and then write your command
aabidhashmi said:
Here is is collection of all custom recoveries for YU Yureka and detailed guide to Root YU Yureka without changing Stock Recovery
Requirements
1. YU Yureka (obviously) with USB Data cable
2. PC / Laptop (Having Windows installed at least Windows 7 or above)
3. Drivers (Windows Automatically detect and install the required drivers)
4. ADB & Fastboot binary package that can be downloaded from XDA 15 seconds ADB Installer v1.4.2']http://forum.xda-developers.com/showthread.php?t=2588979
5. Custom Recovery (Anyone in which you are interested CWM, PhiZ, TWRP)
6. Latest SuperSU.zip file to root your phone
Warning: This process may delete all data stored in internal storage so better backup all the files stored in internal storage.
Step One
Enable USB Debugging on your device you can just follow these steps:
Go to Settings> About phone and keep taping on build number at least 7 times or till it appears "You are a developer now",
Now again go to settings>developer option (only after the previous step it will be enabled)> check/select USB debugging.
Step Two
Unlock your bootloader to flash custom recovery and root.
Here is the process
1. Download the adb & fastboot binary package and install it.
2. Power down phone
3. Plug USB cable to your PC
4. Press and hold Vol Up button and plug other end of USB to your device, soon you will see the fastboot screen.
(or without plugging USB Cable, Press and Hold Power and Vol Up buttons simultaneously, until you see the screen
"FASTBOOT MODE"
5. Device drivers will get installed by windows (please wait for the driver installation to complete)
6. After driver installation is done go to the folder where you have extracted the package
7. Now open elevated DOS command prompt (terminal) on your PC and go into the same folder where you saved the recovery file
* to start command prompt directly from desired folder, while holding the Shift Key Right Click on folder and select start "open command window here"
8. Type the following command to check if the device was detected in fastboot mode
fastboot -i 0x1ebf devices
you should get output like : 2a25d00 fastboot
if you don't get similar output it means that the drivers weren't correctly installed or the device wasn't connected properly
9. If the output is similar to above then run the following command:
fastboot -i 0x1ebf oem unlock
you should get output something like :
.....
OKAY [ 0.003s]
finished. total time: 0.004s
10. Now your bootloader is now unlocked.
Step Three
Root your phone without changing your stock recovery
1. Download SuperSU.zip and put it on root of your internal or external SD card
2. To load custom recovery (CWM / TWRP / PhiZ) temporarily, now type this command in terminal :
fastboot -i 0x1ebf boot recovery CWM_6.0.5.1_recovery-yu.img
*Note : if your download custom recovery is named differently (here CWM_6.0.5.1_recovery-yu.img) then while writing the above command you need to put the name of the recovery same as as your saved file name (anyone CWM / Phiz / TWRP)
Done ! You flashed custom recovery temporarily.
3. Now press and hold "Vol up+ Vol down + Power" buttons simultaneously to boot into custom recovery.
4. To gain root access flash SuperSu.zip that is stored on your internal or external SD card (in step 1)
5. Choose reboot phone and enjoy rooted phone without changing stock recovery !
Downloads
1. 15 seconds ADB Installer v1.4.2 http://forum.xda-developers.com/showthread.php?t=2588979
2. Super SU latest v2.46 http://download.chainfire.eu/696/SuperSU/UPDATE-SuperSU-v2.46.zip
3. CWM 6.0.5.1 https://s.basketbuild.com/devs/vishal_android_freak/yu/yureka
OR http://d-h.st/ElAe
4. PhilZTouch 6.59 based on CWM v6.0.5.1 http://www.androiddevs.net/downloads/
OR http://d-h.st/UqWK
5. TWRP 2.8.5.0 http://techerrata.com/browse/twrp2/tomato
OR https://www.androidfilehost.com/?fid=95916177934528156
OR http://d-h.st/5wDD
Special Note
Without the vendor id, phone will not get detected in fastboot mode.
Like if you want to check fastboot type this :
fastboot -i 0x1ebf devices
therefore, always add "i -0x1ebf" after fastboot and then write your command
Click to expand...
Click to collapse
Few errors noted:
1. You can't say flashing recovery when you are booting it.
2. In step 3 point 3 is not valid because when your command is to boot it will automatically boot into recovery you need not use combination keys.
3. Last point vender id is wrong !!!
Few suggestions:
1. It feels like you have not tested this by yourself
2. There is already a guide for "rooting without flashing recovery". Search before posting.
Regards
aashking
aashking said:
Few errors noted:
1. You can't say flashing recovery when you are booting it.
2. In step 3 point 3 is not valid because when your command is to boot it will automatically boot into recovery you need not use combination keys.
3. Last point vender id is wrong !!!
Few suggestions:
1. It feels like you have not tested this by yourself
2. There is already a guide for "rooting without flashing recovery". Search before posting.
Regards
aashking
Click to expand...
Click to collapse
Dear aaskking
Thanks to inform. Here is the corrections
1 & 2 - Tutorial updated with "boot" and "flash" commands separately.
3 + Vendor ID is correct nothing wrong in it.
4 - I already tested all those procedures and commands. I never post anything without testing.
5 - Yes, I also seen that available guide, but that is not so much detailed and also required files links are not provided.
Anyway, thanks for your suggestions.
aabidhashmi said:
Dear aaskking
Thanks to inform. Here is the corrections
1 & 2 - Tutorial updated with "boot" and "flash" commands separately.
3 + Vendor ID is correct nothing wrong in it.
4 - I already tested all those procedures and commands. I never post anything without testing.
5 - Yes, I also seen that available guide, but that is not so much detailed and also required files links are not provided.
Anyway, thanks for your suggestions.
Click to expand...
Click to collapse
EDIT : You can get OTA updates with root..
After the update is flashed you will loose root access ..
To keep it or to avoid this please write the following step
STEP) In Developer Option UNTICK -"Update CM Recovery".
That's it.. Cheers mate wonderful thread.. @aabidhashmi @aashking
arjunsingh1000 said:
EDIT : You can get OTA updates with root..
After the update is flashed you will loose root access ..
To keep it or to avoid this please write the following step
STEP) In Developer Option UNTICK -"Update CM Recovery".
That's it.. Cheers mate wonderful thread.. @aabidhashmi @aashking
Click to expand...
Click to collapse
Thanks Arjun Singh @arjunsingh1000 for suggestion and appreciation
Post updated ...
aabidhashmi said:
Thanks Arjun Singh @arjunsingh1000 for suggestion and appreciation
Post updated ...
Click to expand...
Click to collapse
Great mate cheers just checked and tried that ota updates are available and work.. On stock recovery... Locked bootloader and with root..
Achieved this by downgrading to the very first cm11 firmware and got then rooted it and locked the bootloader then I just booted it and got the incremental update .. Downloaded and flashed .. Works perfectly.. Root not lost due to the untick in dev options..
Thanks again Arjun Singh, for confirming OTA updates are working.
I am already on Stock ROM & recovery {rooted} and tried the same procedure {locked the bootloader}, but no updates for me.
Is updates are really there, or something wrong with me ?
Sent from my AO5510 using Tapatalk
I am simply unable to get the device listed in command prompt after fastboot mode is enabled. my phone has option to boot into fastboot mode in power options. i tried that option, i tried using command to boot into fastboot. But somehow, when phone is in fastboot mode, it does not get detected by fastboot application (even though windows installs drivers successfully).
I have tried 3 different laptops. All had same problem. No idea how to solve this.
aabidhashmi said:
Thanks again Arjun Singh, for confirming OTA updates are working.
I am already on Stock ROM & recovery {rooted} and tried the same procedure {locked the bootloader}, but no updates for me.
Is updates are really there, or something wrong with me ?
Sent from my AO5510 using Tapatalk
Click to expand...
Click to collapse
Well I guess you are on the latest build XN0PHQ I guess? Another beta update was made but not rolled out it is um XNPH08P I know its a little late but just in case you don't know..
---------- Post added at 05:30 PM ---------- Previous post was at 05:28 PM ----------
jitendragarg said:
I am simply unable to get the device listed in command prompt after fastboot mode is enabled. my phone has option to boot into fastboot mode in power options. i tried that option, i tried using command to boot into fastboot. But somehow, when phone is in fastboot mode, it does not get detected by fastboot application (even though windows installs drivers successfully).
I have tried 3 different laptops. All had same problem. No idea how to solve this.
Click to expand...
Click to collapse
Ahahahaah... I know just the way... Do not reboot via adb ...
Switch off your phone remove your battery and put it back in do not turn it on.. But connect your USB cable and at the same time hold the power up or maybe down button .. Voila your in fastboot which will get detected .. Don't forget to use the vendor id.
arjunsingh1000 said:
Ahahahaah... I know just the way... Do not reboot via adb ...
Switch off your phone remove your battery and put it back in do not turn it on.. But connect your USB cable and at the same time hold the power up or maybe down button .. Voila your in fastboot which will get detected .. Don't forget to use the vendor id.
Click to expand...
Click to collapse
I tried this method but phone does not get detected in fastboot mode at all. I have drivers installed for all different modes I connect my phone as. No luck at all.
Also, weird thing is, I have an option to directly go to fastboot mode from the power menu.
Jitendra Garg
Your driver's are not installed
As there is no special drivers setup, so connect your PC with Internet then plug your phone and let Windows install drivers automatically.
Sent from my AO5510 using Tapatalk
Hi.
Well as i said in my last topic,My tablet went on a auto rotation and etc.
http://forum.xda-developers.com/fonepad-7/help/stuck-boot-screen-fonepad-7-k012-t3267240
Selected recovery,Gave me an error.
So,Now i used a Jellybean firmware on Asus site.
Used those delete userdata and cache and system and etc.
Then loaded those 3 img files,It worked fine in droidbot.
But when i choosed recovery,It gave me an error after some seconds(Around 20 sec)
Well,Then i thought maybe i should use kitkat,So i download its firmware on Asus site.
Done those steps,Used SD update,It gave me same error again.
What should i do now dudes?
Please someone help me its URGENT! :crying: :crying:
P.S:Errors i told,I meant that andriod guy resting with a red attention...
Steps i have done already:
Used With/Without Wipe data button,Then used fastboot erase system and fastboot erase userdata and fastboot erase cache
Then load splashscreen and etc.
With both JB-KK firmwares.
I renamed firmwares to k012_sdupdate.zip and put it in an external SD.
Any way to save me? :/
---------------
IFWI VERSION:64.25
DROIDBOT:10.32.1.22.1
NOTE: MAKE SURE YOUR DEVICE IS MODEL NO. K012 FE170CG
BEFORE YOU CONTINUE
1. Download ADB and Fastboot : [TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2
2. Install ADB drivers : Intel Android USB Drivers
3.Download Previous Firmware from Asus support site.
4. Download this for temporary tethered cwm
ACTUAL PROCEDURE
1. copy the firmware (.zip) to an external sd card
2. Extract downloaded recovery.rar
3. Put your device in Droidboot mode by holding both power button and vol down while device is turned off.
4. Connect device to computer. Open cmd and type "fastboot device" to verify.
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
6. Some stuff will appear after that. Dont do anything. In a few moments CWM will load.
7.Next part is pretty self explanatory. use volume keys to go up and down and press power to select option. choose install zip. in the next menu choose install from external sd card*. Choose the zip file you downloaded from Asus website, if installation fails download another version from the support website.
FISRT BOOT MIGHT TAKE SOME TIME.
* I dont remember the exact wordings.
------Hit thanks if this helped you------------