Dear all,
My Universal has been stuck in the bootloader screen after upgrade with DOPOD Rom. I have searched thru the threads but have had no luck so far. Has anyone out there experienced this? Please help me out
Thank you
Ken
STUCK RELEASE!?!?!
Well.very easy for start.
ROM Upgrade Failure
It is possible, in a very small number of ROM upgrades, that the upgrade could fail. The following are workarounds to get the device working and upgraded.
Device stuck in 'Bootloader' mode
When this happens the device screen will be blank except for the words:
Serial v 1.00a
The word [Serial] should change to [USB] when the cradle is plugged into the PC, and the version number below this will vary. When you get this screen, a soft or hard reset will not make any difference.
It is still possible to run the ROM upgrade file again, without using Activesync (Activesync will not restart anyway).
• Firstly unplug the USB cradle and reboot the PC
• Plug the cradle back into the USB port (this must plug directly into the USB port and not into a USB Hub / adaptor).
• Now run the ROM upgrade file again from the PC. This should just run as per normal and correctly reflash the device.
If it is still not working,try this
• Press & hold the power button
• Press & hold the Backlight button
• Push the stylus into the soft reset hole - until you see the word [Serial] on the screen.
• You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
It work for me,goodluck
henning
find an attachment how to fix this
Many thanks, HENNING RAS
My device is up & running again. Thanks
Ken
hello
i have htc one x (unlocked and rooted) i manage to install cyanogenmod and it worked
while my phone is working i press power + plus down in order to reach bootloader mode the phone screen goes black and it refuses to boot
and refuses to charge -- i tried a lot of combinations but not useful
when i connect it to pc it recognize it as apx mode then unknown device
i installed driver for apx mode and it reecognize it as nvidia usb boot recovery driver for mobile devices
i tried to use nvflash but no manual on how to flash boot available in the net
so any suggestions or help
thanks
Hmm well APX means usually a hardware fault (brick) most posts about APX and its solution are temporary !
Sorry.....getting the mainboard replaced is the best option.
since we have no htc in our country can I replace the main board
Well sure if you have the knowledge and nerves to do it.
Hello geeks,
here I have bricked my phone fault false manipulation, I end up with the HTC logo loop !!!!!!!!!!
I have no Access to bootlaoder with low volume + power
by cons when I made up volume + power I can access the recovery <3e>
I can not flashing the bootloader or install a new rom since my recovery are not a custom so do not let the file not sign
you can flash a recovery from a third recovery via SD card?
Another prob;
when I try to do (apply apdate from ADB) my laptop does not detect my phone driver, sometimes I have ADB android interface, sometimes htc dream !!!
I install HTC driver, htc sync, adb driver, 68xx prelooderdriver SDK manager.
*
I'm really sad because I use my new phone 3 days: mad:
I keep in mind the moral view that prevails on the forum
thank you in advance
Sory for the late nswe, but I first seen it now
but tell me how has it gone with your phone? If it still makes problems I've to know which model it is: a5dwg, a5dug, a5UL, Single or dual Sim
Scorpio
Hello guys! I am following you since yesterday morning when I wake up because my HTC Desire 320 was in a continous vibration restarting again and again every 10 seconds. Only the Android logo appears for a few secs and new restart and so on. I looked around a liitle, downloaded all the tools including Sp flash tools, preloader drivers for Windows 7, MT6582 scatter and so on. The phone was never rooted, is unlocked. I tried with Sp flash tools unsuccesful, the write process fails I guess because connecting and disconnectiong from usb even with the battery removed. Can't access recovery mode with volume down and power button and battery inside, same event appears. What is the next step? Thank you
Hello ! I had a problem on my FE375CG. It was rooted, and after an ASUS update, my device stuck with only a USB logo on the screen ! No Boot Droid nothing. There was a lot of error and I was unable to flash my device with Fastboot...
But I prepared a kit with a lot a tools to unbrick the devices ! I don't really know who are the authors of this tools, but here is the pack !
First Download the package : "Unbrick_Fonepad_7.zip" : https://mega.nz/#F!qM0EECyA
Second, unzip the package. Install the ADB drivers and the Intel DnX USB Drivers.
Then, Maintain + and - and power on your device for 4 secondes. The screen should remain off.
Connect the tablet to your computer : It should be recognize, screen remaining off.
Then you have to run the "Predowngrade.cmd" in the "3 - PreDebrick" directory.
At the end, you will see an Intel Logo (hourra). Disconnect you device, power off.
Then you have to run the "Downgrade.cmd" in the "3 - Full Debrick" directory.
The processus will stop, and the intel logo appears again.
Maintain + and - and power on your device for 4 secondes. The screen should remain off.
Disconnect you device, power off.
Then, Maintain + and - and power on your device for 4 secondes. The screen should remain off.
Reconnect your device
And hit enter on your computer.
And... Tadaaaaaaaaaaaaaaaaa ! It should work again ^^ ! You have just to flash the last firmware with Bootdroid ! Last firmware can be found here : https://www.asus.com/support/Download/28/7/0/10/Ss6JyhD8bOcmeH6f/32/
Sorry for my english, I'm french ^^ ! Hope it will help some peoples.
Will this work for k004?
Hello,
my FE375CG is bricked: when I turned it on, it's stuck on INTEL logo.
I tried your method, but, after third passage, I can't turned it off. So I waited battery discharge, but when I plug to recharge, the tablet turned on and stuck on INTEL screen, I' can't proceed to the fourth step (I' can't maintain + and - and power on your device for 4 seconds, it turns itself on, remains on INTEL bootscreen and I can't do anything)
Have you some suggestions?
This tutorial work for K01N/FE171CG??
Alviyansyah said:
This tutorial work for K01N/FE171CG??
Click to expand...
Click to collapse
I'd like to know as well.
Sent from my ASUS_Z00LD using Tapatalk 2
Successfully unbrick my ASUS FONEPAD 7 (FE375CG)
after trying more than 10 times i am succeeded. 2nd step of fulldebrick is quite difficult but it works.... volume + and - and power button pressing just 4 second and at 3rd second the screen will flash lightly which can be observed in dark environment.
help me please......... i have an FONEPAD 7 , but its ME175CG... probably i've bricked the device... i cant load recovery mode, the device is blocked in logo android green, and my pc doesn't read nothing!!! PLEAZ HELP ME!!!!
Fonepad k004 me371mg
Hello. I need a help tô my fonepad k004 me371mg. Its bricked. No droidboot. .. no system... nothing. .. only asus logo or usb cable logo. .. the imagem o found only raw formar. ... Tks
Is work in K00E? i need help
suzukube said:
Hello ! I had a problem on my FE375CG. It was rooted, and after an ASUS update, my device stuck with only a USB logo on the screen ! No Boot Droid nothing. There was a lot of error and I was unable to flash my device with Fastboot...
But I prepared a kit with a lot a tools to unbrick the devices ! I don't really know who are the authors of this tools, but here is the pack !
First Download the package : "Unbrick_Fonepad_7.zip" : https://mega.nz/#F!qM0EECyA
Second, unzip the package. Install the ADB drivers and the Intel DnX USB Drivers.
Then, Maintain + and - and power on your device for 4 secondes. The screen should remain off.
Connect the tablet to your computer : It should be recognize, screen remaining off.
Then you have to run the "Predowngrade.cmd" in the "3 - PreDebrick" directory.
At the end, you will see an Intel Logo (hourra). Disconnect you device, power off.
Then you have to run the "Downgrade.cmd" in the "3 - Full Debrick" directory.
The processus will stop, and the intel logo appears again.
Maintain + and - and power on your device for 4 secondes. The screen should remain off.
Disconnect you device, power off.
Then, Maintain + and - and power on your device for 4 secondes. The screen should remain off.
Reconnect your device
And hit enter on your computer.
And... Tadaaaaaaaaaaaaaaaaa ! It should work again ^^ ! You have just to flash the last firmware with Bootdroid ! Last firmware can be found here : https://www.asus.com/support/Download/28/7/0/10/Ss6JyhD8bOcmeH6f/32/
Sorry for my english, I'm french ^^ ! Hope it will help some peoples.
Click to expand...
Click to collapse
Your tutorial is not working for ASUS K004 and file xfstk-dldr-solo can not be run..
My device is not recognized by the pc. It shows the usb logo everytime. I opened the back cover and disconnected the battery. As soon as i connect the battery it turns on by itself, vibrates twice and shows the usb logo. it only turns off if i disconnect the battery. Without the battery it has the same behaviour if i connect the usb cable. None of the keys works except the VOL- or VOL+ and VOL - or PWR and VOL-. If i press vol- or any combination that has VOL- and connect the battery or the cable the device wont turn on and is not detected by the pc. If i do it with vol + or power or a combination of both it starts like i said earlier with two vibrations and the usb logo but not being detected. I'm lost because it being detected by the pc is a requirement. I installed drivers from folder 1 - ASUS_Android_USB_drivers_for_Windows and folder 2 - IntelDnXUSBDriverSetup.
The device is a FE375CG (K019) Asus Fonepad 7
Tried with windows 10 x64 on 2 different computers.
PS: I have disabled driver signature enforcement.
Hi
How can I obtain .img files for K00E (me372cg) ?
if Predownload Cmd worked just proceed to full debrick Download-3cmd then install updated firmware BESURE TO RENAME OFFICIAL FIRMWARE TO MOFD_SDUPDATE.zip it will auto install in recovery mode.