So, i scoured the forums, searched for my error code and nothing...
I have a new E980 that I rooted, installed CWM on and left the stock ROM. Earlier today, I get a notification for an OTA update.
I figured I didn't desperately need root, so I unrooted through SuperSU, and said to hell with it, and accepted the update.
Phone reboots into CWM and is now only booting into it over and over.
I looked up how to recover from it, and I've been trying to flash it using LG Flashtool ver 1.5 and everything goes fine until I actually plug the phone in with download mode on and LG FT in the "Ready!" state. LG FT then starts to flash it, goes to 3%, immediately to 100% and then fails after 5 seconds. Error code F0000002. I tried everything over and over again and I get nothing.
I have my COM port set to 41 and LG Flashtool set up properly according to the tutorials.
Any ideas?
I had to use the LG R&D test tool to flash the panama rom then root & install CWM. With freegee and then restore my stock.E980 AT&T backup. Kept getting a "Previous loadfailed" error with LG flash tool.
http://forum.xda-developers.com/showthread.php?t=2420219
Hoping someone can help me here.
My wife has a G3 that started acting up back in September or so. It would randomly turn off and reboot, usually while not even touching it. Did some looking around and found that the Facebook Messenger app could cause some instability. Removed the app, all was good for a couple of weeks before it started again. This time, we backed everything up, did a factory reset, all was good for about a week. Reboots started again so I did a hard reset from Recovery. Booted up, everything was good again for about a week again before the reboots started up. The wife ended up giving up on it and went back to her Galaxy S3.
I've been messing around with it today. Phone has been stuck in a boot loop at the LG logo. Battery is fully charged. I followed some guides and downloaded the V10c stock firmware TOT file, dated June 20th, 2014 and LGD851_20140611_LGFLASHv160.dll and loaded them up into LGFlashTool v1.8.1. Installed fresh LG drivers on my Win7 PC, followed the flashing instructions to the letter using a USB 2.0 port (as I read somewhere that 3.0 ports have caused issues on some devices). Everything flashes 100%, flash tool reads complete, phone shows a big 3 on the screen with a blue background. Unplug and reboot the device and it's right back to a boot loop at the LG logo.
Now at one point, during the flashing process, it would boot into LG MiniOS 3.1 and I was able to choose an option (chose Normal Boot) and it would go back into the boot loop. Also, I connected it to my Ubuntu machine just to see what would happen and I received an error "Unable to mount LGE Android Phone. Unable to open MTP device", which makes sense. However, the phone itself would get to the T-Mobile logo and briefly jump into the initial setup of the phone before jumping back to the LG logo and starting over again. Connecting back to my Win7 machine, it just boot loops unless I have the flash tool running. Not having USB connected, it just boot loops.
I'm at a loss here. I can usually muddle my way through these kind of things but this one has me completely stumped. Ordinarily, I wouldn't worry much about this but she's wanting to get a new phone through T-Mobile's JUMP program and we can't do that if the phone won't even boot.
Any help would be appreciated.
Valorendk said:
Hoping someone can help me here.
My wife has a G3 that started acting up back in September or so. It would randomly turn off and reboot, usually while not even touching it. Did some looking around and found that the Facebook Messenger app could cause some instability. Removed the app, all was good for a couple of weeks before it started again. This time, we backed everything up, did a factory reset, all was good for about a week. Reboots started again so I did a hard reset from Recovery. Booted up, everything was good again for about a week again before the reboots started up. The wife ended up giving up on it and went back to her Galaxy S3.
I've been messing around with it today. Phone has been stuck in a boot loop at the LG logo. Battery is fully charged. I followed some guides and downloaded the V10c stock firmware TOT file, dated June 20th, 2014 and LGD851_20140611_LGFLASHv160.dll and loaded them up into LGFlashTool v1.8.1. Installed fresh LG drivers on my Win7 PC, followed the flashing instructions to the letter using a USB 2.0 port (as I read somewhere that 3.0 ports have caused issues on some devices). Everything flashes 100%, flash tool reads complete, phone shows a big 3 on the screen with a blue background. Unplug and reboot the device and it's right back to a boot loop at the LG logo.
Now at one point, during the flashing process, it would boot into LG MiniOS 3.1 and I was able to choose an option (chose Normal Boot) and it would go back into the boot loop. Also, I connected it to my Ubuntu machine just to see what would happen and I received an error "Unable to mount LGE Android Phone. Unable to open MTP device", which makes sense. However, the phone itself would get to the T-Mobile logo and briefly jump into the initial setup of the phone before jumping back to the LG logo and starting over again. Connecting back to my Win7 machine, it just boot loops unless I have the flash tool running. Not having USB connected, it just boot loops.
I'm at a loss here. I can usually muddle my way through these kind of things but this one has me completely stumped. Ordinarily, I wouldn't worry much about this but she's wanting to get a new phone through T-Mobile's JUMP program and we can't do that if the phone won't even boot.
Any help would be appreciated.
Click to expand...
Click to collapse
Good afternoon, my recommendation is that flashes with lg flash tool 2015. All you need is your phone updated driver installed on your pc. Further, you need to download the KDZ (firmware of your stock rom) corresponding to your model. Look at the XDA thread as do or YouTube. If you need more help, you can consult here.
cesarandres_8911 said:
Good afternoon, my recommendation is that flashes with lg flash tool 2015. All you need is your phone updated driver installed on your pc. Further, you need to download the KDZ (firmware of your stock rom) corresponding to your model. Look at the XDA thread as do or YouTube. If you need more help, you can consult here.
Click to expand...
Click to collapse
IIRC, he's talking about going back to the latest stock firmware available from LG and flashing with with @quangnhut123's flash tool.
Thanks for both of your help on this. I actually had given up on the phone for a while. The last time I flashed, it was allowing me to get into the first time setup but wouldn't let me complete setup before rebooting. So I ordered a new battery and everything is working like it's brand new. Thanks again!
So I rooted my phone by installing the rooted 13b img. And went to install xposed framework and apk. I completed all the steps found here (http://forum.xda-developers.com/g4/themes-apps/guide-installing-xposed-locked-t3181593), and now it is stuck on the android logo....suggestions on what do do from here?
A little more detail: After completing steps verbatim, it would fail to install framework. I then read somewhere else that you need to uncheck not only auto mount but the mount option, as well. I tried that and it seemed like it must have worked as it didn't immediately fail and reboot. However, it got stuck on the android logo and after an hour or so I realized there was problem. I have pulled the battery and rebooted several times. I can boot into download mode, but cannot get it to fully boot. Since I could get it into DL mode, I used LGUP to install the 24C MM update (as I didn't have the 13B on my computer). But the result is the same...stuck on the Verizon logo even after a successful install of 24C.
Is this a case of the hardware failure that others are experiencing or is this software related? I see a lot of people with bootloop issues and mine seems to be similar but different. Mine does get past the LG screen to the next screen, but even installing a stock kdz doesn't seem to help...
UPDATE:
Well I downloaded the stock 13B kdz and flashed it via LGUP and it somehow managed to boot. It looked like it was going to be stuck on the Verizon landing page but after about 10 seconds or so it completed boot up. I have now installed the rooted 13B image and made a backup img. I might try again to install xposed framework - fingers crossed it doesn't screw up this time...
Use hyleton's 'LG G4 Stock Firmware (Go Back to Stock) KDZ & TOT Method' that uses LGFlashTool2014.exe and do a CSE Flash - this will wipe all your data though
SnitchyB said:
Use hyleton's 'LG G4 Stock Firmware (Go Back to Stock) KDZ & TOT Method' that uses LGFlashTool2014.exe and do a CSE Flash - this will wipe all your data though
Click to expand...
Click to collapse
Thanks, I'll look into that. I was hoping that using LGUP to reflash to stock would do it...but I guess I have to remove whatever the flash tool put on my phone when trying to install the xposed framework...
Hi,
So my LG G3 D855 is stuck in a very persistent bootloop since the last couple of days. I have tried everything but can't seem to bring it out of its soft-bricked state.
Here is the lowdown:
> It all started with an innocent restart.
> The phone was reverted from an earlier root. So it is unrooted at the moment.
> No recovery images are installed.
> The phone is stuck at the LG screen but weirdly sometimes goes till the 'optimizing x of x apps' screen before returning to the god forsaken loop again.
> Before getting soft-bricked it was running stock Marshmallow.
> Have tried factory resetting.
> Phone enters into download mode just fine.
> Have tried flashing stock roms via both LGUP and LG Flash tool:
} ROMS tried: D85530B_00_1217_16G (MM) and LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0 (KK)
) With LGUP, my phone's model isn't recognized so can't get any further.
} With LG FLashTool, I manage to get to the 'downloading' step (after CRC bin check). The phone also displays the firmware update screen successfully. However, only like a second into the downloading the FT fails and gives the error 'can't get handset information' (or something of this sort).
} Using the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0 dll with the KK rom and LGUP_8994 dll with the MM rom.
Any and all help will be appreciated guys!
Thanks!
Anyone?
You should ask here: http://forum.xda-developers.com/showthread.php?t=2785089
I managed to fix my phone just today.
After every flash tool had failed, I gave LG Mobile Support Tool a shot. And it detected my phone just fine. Then I managed to reflash my device using the Options > Upgrade Recovery settings. However, this didn't effect my situation.
Then, I successfully flashed the 2014 factory firmware using LG Flash Tools, and it showed Download failed on the first reboot. I was encouraged because it took like 2 minutes to get there. Initially it was failing like 10 seconds in.
Anyhow, by that time my phone had booted into the MiniOS where it showed a prompt that said "Touchscreen autotest, please don't tap anywhere" or something. I let it be for a while and it didn't budge afterwards I tried tapping 'OK' but it didn't register with the phone. Then I tried the power button shortcut to get to MiniOS > Normal boot and that wouldn't work as well. I thought something was definitely wrong with the touch system of the phone. So, I opened it up and lo-and-behold the digitizer cable was loose, it had almost become undone. After I had reseated it on the pin and powered my phone back on, it went straight to the initial setup screen - the one with the Google account and stuff.
Alas! All this for a frikkin' loose cable. Now I have to get my phone back to Marshmallow from Kitkat with iterative updates. :/ Still better than a brick of a phone though!
Just leaving it here unless someone else runs into a problem of this sort!
Cheers!
Hello everyone,
yesterday I flashed a new Cyanogenmod 14 nightly (12062016) for my G4 from earlier nightly in TWRP. After reboot the phone keeps going back to TWRP and I can't seem to get it to boot to system..
I tried factory reset, reflashing back to old nightly, flashing stock.. but nothing seems to work.
Also tried doing this in the TWRP terminal:
dd[space]if=/dev/zero[space]of=/dev/block/platform/f9824900.sdhci/by-name/fota
Didn't fix the loop, I guess because it wasn't the OTA update that caused the problem in the first place.
If anyone has an idea, I would greatly appreciate the help!
Thanks.
If you can reach download mode you could try reflashing back to stock then starting again.....Hope you get yours fixed - Sorry to say this but mine did a very similar thing only 24 hours before you posted!!! Only mine was on stock FW and was in use at the time - I've now had to swap it as valuebasket who sold me the phone have ceased trading. If yours is a UK model you may be able to get it replaced under warranty - believe that LG guarantee their phones for 2 years and a ruling by the European court said that flashing a custom rom doesn't invalidate any warranties.
I have the same exact issue, I also flashed the latest CM14 nightly and cannot get the device to boot any rom.
I have even tried flashing stock rom but I get the same problem.
From what I have read, the bootloop issue happens once the device boots but I don't seem to be getting that far.
Any ideas?
Ran into the same problem 3 days ago. This is the first time I have encountered a non-revertible issue in 3 years as a cyanogenmod user. This changes my opinion on how safe it is to make use of a custom ROM. I tried to wipe everything, reinstall TWRP, change TWRP with another recovery, reinstall a safe NAND backup of mine.....nothing.....it went into boot loop. Before I read this post, I was convinced my phone encountered the infamous G4 bootloop problem.....now I see there are other examples, so it shouldn't be the case. Long story short, I had to check my device in at the LG assistance, with 25 days as time forecast.
The guilty nightly was 20161205.
I have never seen anything like this...
This has solved it for me - I installed LG Bridge and flashed the factory firmware using the tool. Now it seems I'm back on stock but at least it's working.
got mine working. I had to install LGUP and flash stock ROM. Once flashed I installed CM14 and I am back up and running again.
I tried LGUP but it could not recognize the device while this was looping.....a bad experience......
I have the same issue. My phone was updated to 20i via the original stock firmware, then I put twrp 3.0.2-0 and cyanogenmod on. I did a cyanogenmod update from within cyanogenmod, which just booted into twrp, then I manually installed the update zip that cyanogenmod had downloaded, then it always boots into twrp. I wonder if initiating the update from within cyanogenmod was the cause. The phone is not detected by LGUP or LG Bridge. I've tried this on a win10 machine, and a win7 vm from linux. I have access to twrp, and download mode by doing the reboot into bootloader from within twrp.
If those people who have fixed this could give more details about how they did it, that would be good. What exact steps did you take? What stock firmware version did you have before installing a custom rom? What OS version were you using? What twrp version?
Well. Mine got stuck in bootloop for the second time today. What is going on? In between the two bootloops I had one good update with CM. Using TWRP 3.0.2.1. Steps to reproduce failure: updating CM from within CM, it autoreboots into TWRP and after that nothing happends, no autoinstall. Then after a manual install of the new CM the bootloop starts.
Resolve the problem:
* Install LGUP 8994 DLL Ver 0 0 3 23, Install LGUP Install Ver 1 14, get the latest KDZ
* Get the phone into download mode with usb cable and after that in firmware update mode
* Startup LGUP and choose refurbish and select the kdz file.
* After that you can boot into your stock LG firmware again, reinstall TWRP an CM. If you want so.
Read that it is advised to manual update cm from within TWRP. TWRP will get an update in the future to solve this bootloop problem.
iankelling said:
I have the same issue. My phone was updated to 20i via the original stock firmware, then I put twrp 3.0.2-0 and cyanogenmod on. After a cyanogenmod update, it always boots into twrp. The phone is not detected by LGUP or LG Bridge. I've tried this on a win10 machine, and a win7 vm from linux. I have access to twrp, and download mode by doing the reboot into bootloader from within twrp.
If those people who have fixed this could give more details about how they did it, that would be good. What exact steps did you take? What stock firmware version did you have before installing a custom rom? What OS version were you using? What twrp version?
Click to expand...
Click to collapse
I second that. Same issue and neither LG Up nor LG Bridge will recognize my device. Looking in device manager there are no serial interfaces. Do I need a special driver that provides a com port for a phone in recovery or fastboot mode?
---Edith 2016-12-12: Found a solution for my issue:
The phone has to be in _download_ mode, not in recovery or fastboot. After realizing that I have to boot the phone in a different manner, it will be recognized by LG UP.
Here is how to boot the pone in download-mode:
- Power off your LG device.
- Press and hold Volume Up button.
- Connect your device to PC with a USB cable while holding the Volume Up button.
- You’ll boot into download mode with “Firmware Update” written on top of the screen.
Now everything is fine again.
croclacrimae said:
Hello everyone,
yesterday I flashed a new Cyanogenmod 14 nightly (12062016) for my G4 from earlier nightly in TWRP. After reboot the phone keeps going back to TWRP and I can't seem to get it to boot to system..
I tried factory reset, reflashing back to old nightly, flashing stock.. but nothing seems to work.
Also tried doing this in the TWRP terminal:
dd[space]if=/dev/zero[space]of=/dev/block/platform/f9824900.sdhci/by-name/fota
Didn't fix the loop, I guess because it wasn't the OTA update that caused the problem in the first place.
If anyone has an idea, I would greatly appreciate the help!
Thanks.
Click to expand...
Click to collapse
I was able to get out of that by also wiping by-name/misc. Don't do that, though, because then your wifi mac address will get messed up and you'll spend all day looking for a permanent fix for that.
I suggest reflashing a stock KDZ using LGUP, as others have said. You can get the usb drivers from LG Bridge.
I will release a fix for that soon. Check the twrp thread for updates on this.
Hi
I also have this problem
I installed cm-14.1-20161201-NIGHTLY-h815 successfully and was running it for almost 2 weeks without issues, today I updated to cm-14.1-20161213-NIGHTLY-h815 from cmupdater and I have been ending up in recovery every time I rebooted.
I tried flashing the latest cm recovery and reflashing the rom, with full wipes but no luck.
Full steps of recovering would be appreciated (for example, there are comments about flashing the latest stock rom, but a link to this rom would be helpful)
Thanks
Good news regarding this:
http://forum.xda-developers.com/showpost.php?p=70082901&postcount=213
The above will fix TWRP bootloop issues as well and I also released a first h811 version which should allow installing CM etc as it should.
Keep in mind that this is a BETA and not an official TWRP release.
Please report back in the above thread!
.
Does your twrp beta really fix the boot loop even it is already happening. What do I have to wipe? I have not managed to get out of the boot loop despite intalling it.
Is using using LG Up to flash to the stock rom really the only option?
Edited 2017-01-25 2:45 pm:
Well, sometimes you just have to be patient. Powered down the phone and when th H815 restarted CM did boot. Great. :good:
Hey, I just want to share a small detail, possibly a fluke that helped me overcome the bootloop.
So...I started with a fresh, stock H815, I don't quite remember the firmware version..it was something like version "20g"..
OK, I looked up several guides and tried to get the newest stable versions of each tool. I went through with the official bootloader unlock, then moved on to rooting: Kingroot didn't work for me so I went on installing twrp in fastboot mode so I could afterwards install supersu and root.
I got there eventually but first I was stuck in bootloop - kept ending up in twrp interface. I found the 2 dd commands but those didn't work for me as the msm_sdcc folder did not exist, but instead there was a "f9824900.sdhci". Tried to overwrite this one ...but as others have stated as well, it didn't work.
At that point, I had nothing to lose, I was starting to accept that I had soft-bricked my precious G4 so..I went on installing the DU 10.6 7.1.1 rom and the stock gapps, wiped dalvik, rebooted and held my breath...not literally
About 12 minutes later, after an endless red, spinning logo, my shiny ping pong paddle showed me a different screen, a fresh start welcome screen .
Almost 24h / 10-12 reboots (twrp included) / 70+ apps installed and removed later, the new OS holds around 2G ram average, a bit better battery life, smoother transitions, flawless navigation, flush streaming over both 3G/LTE & 2.4/5 G wifi.
FYI the reboots were intended, wanted to see consistency in boots - we're in the green . Now testing long term stability with moderate/high usage.
There is 1 aspect I noticed, there are a couple of contexts when the interface burps (several menus, various situations, never in apps) and resets back to homescreen...but I think that's more of a launcher topic than an OS one.
Other than that, so far I'm happy with the mod.
Hope my experience helps others that might be in the same spot I was or at lest boosts their confidence to try out a decent idea they might be pondering.