Hi.
Sincere apologies if I'm posting in the wrong place. (I counnld't ask it in the relevant thread since I am a new member and don't have ten posts already (forum rules)
I'm desperate.
I have Huawei Ascend P1 U9200..
Completely stock original build (as far as I know) ICS 4.0.3 Build GBRC00B102.
I want to upgrade to JB, but firstly save (backup) my current ROM.
I've followed this thread http://forum.xda-developers.com/showthread.php?t=2132043&page=49 as well as many others, but I cannot access the bootloader.
I have installed adb and fastboot and drivers from many sources. Nothing works.
Hold Vol- & power button still boots normally.
Use adb - adb reboot-bootloader gives Huawei logo frozen, and PC says "waiting for device". The PC brings up install driver dialogue box but no matter what I do, no driver will install. ADB does recognise my phone using "adb devices" command.
Fastboot command does nothing, but I have noticed in my task manager that "fastboot.exe" continually loads and disappears.
Please can someone tell me how to ccess the bootloader so I can install TWRP recovery and backup my ROM??
Apologies if any of the above is unclear - I'm new at flashing/ROMs etc but usually very good at understanding and following computer jargon
Thank you, in advance, for any assistance
Use Vol+ and Power Button
And for the adb,
Have you installed the correct driver?
The adb/usb driver for your device
May this help you
Give me a thank if helped
Sushant Rohan said:
Use Vol+ and Power Button
And for the adb,
Have you installed the correct driver?
The adb/usb driver for your device
Click to expand...
Click to collapse
Thanks for replying
Vol+ and power button enters the recovery section.
I want to unlock the bootloader, so I can install a different recovery module.
As for adb, I'm sure I have the correct drivers. I've tried many different sources, all with same result.
ADB works, but not Fastboot - and I am assuming that is because I can't unlock the bootloader to enter fastboot mode.
Don't install more than one driver, this may cause the problem with adb. Retain only one driver and then try again later
If this cannot resolve your problem reply me, I would try my best to solve this problem
Sushant Rohan said:
Don't install more than one driver, this may cause the problem with adb. Retain only one driver and then try again later
If this cannot resolve your problem reply me, I would try my best to solve this problem
Click to expand...
Click to collapse
Thanks for your reply.
The adb driver didn't work on the first install. And later I did remove them all and reinstall again just once (because I was getting an "adb server expired" error).
Still no luck.
If you have any other suggestions, I'd be most grateful
In the adb shell type
Adb devices
If you see a long number then try the code given above to unlock the bootloader if not then reply me
I've got the number from adb devices.
How/where do I input it?
May be this link help https://www.dc-unlocker.com/free-huawei-bootloader-unlock-tutorial but here your device is not listed, but you can do a try and have the best of hope. If this did not help you give me a reply as you gave me
---------- Post added at 06:42 PM ---------- Previous post was at 06:33 PM ----------
nudder12 said:
I've got the number from adb devices.
How/where do I input it?
Click to expand...
Click to collapse
What you have to do is
Open the adb
Type
adb devices
Adb reboot bootloader
Fastboot oem unlock
May be this help you
Hit the thank button
Sushant Rohan said:
May be this link help (forum made me delete the link to dc-unlocker) but here your device is not listed, but you can do a try and have the best of hope. If this did not help you give me a reply as you gave me
---------- Post added at 06:42 PM ---------- Previous post was at 06:33 PM ----------
What you have to do is
Open the adb
Type
adb devices
Adb reboot bootloader
Fastboot oem unlock
May be this help you
Hit the thank button
Click to expand...
Click to collapse
Thanks again, but I have already tried DC-Unlocker - it doesn't recognise my phone.
I rebooted to the bootloader using adb reboot bootloader,
and then tried the fastboot reboot oem unlock, but it failed with the following message
"FAILED (remote failure)"
Hmmm. Ok I will get the solution of your problem
Hey Sushant Rohan
Many many thanks for trying to help me, but I think now I have got it working
Many times I tried to enter bootloader and the phone wouldn't allow me. Just once in the last 5 days it did. I tried dozens of times!!!
Today, just one time, it allowed me again, and when it did the PC came up with "need to install drivers for Blaze device".
I remember seeing "blaze" on some forums, so I looked there again to see how to install drivers.
I installed them and PC accepted, but then nothing - device not displayed anywhere or anything.
And after that, again I couldn't access the bootloader in many attempts.
I kept trying and kept trying.
Finally, even though I hadn't done anything different, fastboot finally recognised my device (? fastboot) and I flashed the TWRP recovery image using fastboot command.
Fastboot said success!
I rebooted phone into recovery mode - Vol+ and power button, and there it is - the TWRP recovery mode
Now I'll attempt phone backup. (looking good so far)
Again, thanks so much for trying to help me - I really appreciate someone giving their time to try.
I have no idea why it suddenly worked for me when I didn't install anything new or different etc (but I remember reading another forum where someone said they tried 39 times and it finally worked)
I'm sure I'll reply here again if I have any more trouble
Its my pleasure to help someone in trouble
Sushant Rohan said:
Its my pleasure to help someone in trouble
Click to expand...
Click to collapse
Well, the TWRP backup worked, although I was expecting just one file, but there were many - I suppose I'll have to read some more about TWRP backups!!!
But, booting into bootloader or recovery mode still doesn't work by using the phone buttons - but I can get there using adb commands.
That will have to be enough I suppose.
Thanks again for your efforts
Use can also use Clockwork Mod Recovery instead of TWRP. However both are mire or less similar. So enjoy flashing
Sushant Rohan said:
Use can also use Clockwork Mod Recovery instead of TWRP. However both are mire or less similar. So enjoy flashing
Click to expand...
Click to collapse
Hopefully the next steps will be a lot less painful and time consuming than this was.
I hope to upgrade from ICS to JB now - but I might wait a few days - my loved ones will appreciate me not being stuck on the pc and phone all day for a while
huawei p1 u9200
nudder12 said:
Hopefully the next steps will be a lot less painful and time consuming than this was.
I hope to upgrade from ICS to JB now - but I might wait a few days - my loved ones will appreciate me not being stuck on the pc and phone all day for a while
Click to expand...
Click to collapse
Friend, install mod room cyanogend spanorg 11 android 4.4.4 and install your recovery twr 2.7. but when I turn off my phone and connect the charger to charge battery put off because it opens my only way to recover all your options. the truth is a risk that this well. any to reset or something not nice in the team .. ayudammmeeeee please with that spy on Venezuela. this very good functional room totoalmente great detail just that .. thanks .....
You do not need unlocking bootloader
nudder12 said:
Thanks again, but I have already tried DC-Unlocker - it doesn't recognise my phone.
I rebooted to the bootloader using adb reboot bootloader,
and then tried the fastboot reboot oem unlock, but it failed with the following message
"FAILED (remote failure)"
Click to expand...
Click to collapse
visit www.shuame.com download just plug bootloader mode by pressing power and volume +. the program takes care of downloading drivers adb
Related
Hi all,
My OTA update kept failing so I attempted a manual update to 4.04.
I missed updating the boot.img file. I did the system, recovery and radio then relocked the bootloader.
When I turn it on, it stays on the google splash screen. When I go into bootloader mode and try recovery mode, I get the red triangle. My computer does not seem to be recognizing the phone, I get the error: device not found.
Is there something I might try?
Thanks in advance
AV8ing said:
Hi all,
My OTA update kept failing so I attempted a manual update to 4.04.
I missed updating the boot.img file. I did the system, recovery and radio then relocked the bootloader.
When I turn it on, it stays on the google splash screen. When I go into bootloader mode and try recovery mode, I get the red triangle. My computer does not seem to be recognizing the phone, I get the error: device not found.
Is there something I might try?
Thanks in advance
Click to expand...
Click to collapse
In fastboot mode (obviously), unlock the bootloader, flash the boot image, and leave the bootloader unlocked. Done.
Thanks for the quick repy efrant! A big question is how do I unlock the bootloader if my computer doesn't recognize the phone. I am getting "device not found" so I seem to be unable to unlock the bootloader in the first place.
AV8ing said:
Thanks for the quick repy efrant! A big question is how do I unlock the bootloader if my computer doesn't recognize the phone. I am getting "device not found" so I seem to be unable to unlock the bootloader in the first place.
Click to expand...
Click to collapse
So your GNex is booted in fastboot mode and your computer does not recognize it? If this is the case, it is likely a driver issue, and you should re-install.
It is normal that your GNex is not recognized by your computer when booted not in fastboot mode, when you can't boot.
efrant said:
So your GNex is booted in fastboot mode and your computer does not recognize it? If this is the case, it is likely a driver issue, and you should re-install.
It is normal that your GNex is not recognized by your computer when booted not in fastboot mode, when you can't boot.
Click to expand...
Click to collapse
Hey efrant ^^ I'll sort it out ^^ (if you don't mind)
Dude, chec my sig, all the drivers and tutorials needed, can be found in the Win8 thread.
Follow that tut. then the phone should be recognized. Then erase the phone With:
Code:
fastboot erase system
fastboot erase boot
fastboot erase recovery
This ensures, that the flash is successful. If you don't erase first, it's likely, that the phone won't correctly write the files.
Then flash the files, with these codes:
Code:
fastboot flash boot (Always do this first) <Fille directory\file name.img>
fastboot flash system <Fille directory\file name.img>
fastboot flash recovery <Fille directory\file name.img>
DO NOT ERASE/FLASH userdata!! Do that, and you WILL lose ALL of your data!
If you want, I can help you, with tamviewer. I've helped a few people, this way It has always worked
Normally it does recognize the phone, but it doesn't seem to since I messed this up. I will try to re-install the drivers to see if that works. It is in fastboot mode, I hear the tone from the computer that something has connected when I reboot the fastboot, but it doesn't get recognized.
AV8ing said:
Normally it does recognize the phone, but it doesn't seem to since I messed this up. I will try to re-install the drivers to see if that works. It is in fastboot mode, I hear the tone from the computer that something has connected when I reboot the fastboot, but it doesn't get recognized.
Click to expand...
Click to collapse
Go into the dev manager, and look for: Android 1.0
If you see that, then Update devuice drivers -> Select from a list -> Samsung ADB Interface
That should do the trick
Thanks much, familyguy59. I'll try this now.
AV8ing said:
Thanks much, familyguy59. I'll try this now.
Click to expand...
Click to collapse
No prob. That's what some of us, have made to a "quest" Instead of flaming n00bs, help them, and make sure, they find their place, in this community
Thanks so much efrant and familyguy59! There were a couple of bumps in the road, but I flogged my way through them. I thought I had bricked my phone for sure. Once again, thanks so much.
AV8ing said:
Thanks so much efrant and familyguy59! There were a couple of bumps in the road, but I flogged my way through them. I thought I had bricked my phone for sure. Once again, thanks so much.
Click to expand...
Click to collapse
No prob, dude! That's what we're here for
familyguy59 said:
No prob. That's what some of us, have made to a "quest" Instead of flaming n00bs, help them, and make sure, they find their place, in this community
Click to expand...
Click to collapse
+1 to this guy XD
Sent from my Galaxy Nexus using XDA
jzero88 said:
+1 to this guy XD
Sent from my Galaxy Nexus using XDA
Click to expand...
Click to collapse
And the "xD" was neccessary... in what way? ^^ It is true, though.
If you aren't feeling the same, then it's your thing. I'm here, to help others, and help them understand, what, what features do, and what is needed, to do what....
Hi, my N7 is bricked and I wanted to fix it.
I tried to flash ROM but couldn't do it since my computer wont recognize my N7 (except in Recovery Mode-> Sideload).
I think it has something to do with the "developer options -> need to check USB Debugging", however, I can't do that since my phone when turned on, Google Logo appears, then afterwards, BLACK SCREEN (and now in a loop, but there is no X logo just plain black).
My phone is rooted & unlocked. Out of curiousity (My fault), I bricked my N7.
I've read a lot of article on how to unbrick my N7 and I think I now know how to do it- through Android SDK/ADB Tool. I've also read the a guide on how to change drivers (and tried it in all possible ways I can think of), and it did install the driver. However searching my N7 through ADB Tool doesn't go through.
adb devices
List of devices attached
(**nothing follows**)
But if I turn my N7 to Recovery Mode->apply update from adb:
will show the result:
adb devices
List of devices attached
**serial number** sideload
I don't know what other ways in order to unbrick my N7.
I hope you can help me with it.
You can enter bootloader, right? Then try to use fastboot to flash a new rom.
Use wugs program but tick tablet is in bootloop.
Can you boot a brick in to recovery mode? No...so you aren't bricked...
Thanks for the info man!
AnarchoXen said:
Can you boot a brick in to recovery mode? No...so you aren't bricked...
Click to expand...
Click to collapse
Hi, thanks for the info... I already solved my problem.. If only I have read your post earlier I could've saved xx hours in my research!! LOL
donb1 said:
Use wugs program but tick tablet is in bootloop.
Click to expand...
Click to collapse
I tried, but N7 isn't recognized by PC. So the main problem is really how to make my N7 recognized by PC (ADB/bootloader).
But problem fixed now. Thanks!
Calvin Gross said:
You can enter bootloader, right? Then try to use fastboot to flash a new rom.
Click to expand...
Click to collapse
Before I fixed my N7, this is what I tried. But the problem is, PC wont recognize/find my N7 when I do:
adb devices nor fastboot devices
But, I already fixed my problem. Thanks for the response! Greatly appreciate it!
I own a HTC One V. And I did something at the TWRP menu like installing this CARBON-JB-UNOFFICIAL-20131022-1552-primoc thing.. and ever since then the phone doesn't boot.. it won't even go to that menu where it says FASTBOOT{ I think it's called the recovery menu :3 }
But, I charge it.. And then I plug it into the comp, it just connects and disconnects, like it's giving a faint indicator of life :3
Please help. I was on Ignorance V5..
Installing a rom can't hard brick your device.
Try to shut it down by holding the power button and immediately press vol down + power to enter your bootloader. Then you can select recovery and install a backup of your ignorance rom or do whatever you want.
BTW: It looks like you forgot to install the kernel for the custom rom.
ManishByatroy said:
I own a HTC One V. And I did something at the TWRP menu like installing this CARBON-JB-UNOFFICIAL-20131022-1552-primoc thing.. and ever since then the phone doesn't boot.. it won't even go to that menu where it says FASTBOOT{ I think it's called the recovery menu :3 }
But, I charge it.. And then I plug it into the comp, it just connects and disconnects, like it's giving a faint indicator of life :3
Please help. I was on Ignorance V5..
Click to expand...
Click to collapse
Most likely you flashed the wrong ROM.
PrimoU <> PrimoC
Boot loader should still work as expected I guess:
<vol.down>+<power> should get you to the hboot menu.
kvestas said:
Most likely you flashed the wrong ROM.
PrimoU <> PrimoC
Boot loader should still work as expected I guess:
<vol.down>+<power> should get you to the hboot menu.
Click to expand...
Click to collapse
It's not going into Boot Loader. If it did, I would flash back Ignorance.
Please help
ManishByatroy said:
It's not going into Boot Loader. If it did, I would flash back Ignorance.
Please help
Click to expand...
Click to collapse
Did you try fastboot command to reboot into bootloader?
The command might be accepted by phone during it's initial loading stage:
* connect phone to a computer
* run command (e.g. fastboot reboot-bootloader), must be waiting for response from device
* reboot your phone
* if you are lucky enough the command will be accepted on load.
jonas2790 said:
Installing a rom can't hard brick your device.
Try to shut it down by holding the power button and immediately press vol down + power to enter your bootloader. Then you can select recovery and install a backup of your ignorance rom or do whatever you want.
BTW: It looks like you forgot to install the kernel for the custom rom.
Click to expand...
Click to collapse
It isn't going to bootloader when i press power+volume down button.. :\
If I could enter the bootloader menu, I wouldn't have been this worried. :3
kvestas said:
Did you try fastboot command to reboot into bootloader?
The command might be accepted by phone during it's initial loading stage:
* connect phone to a computer
* run command (e.g. fastboot reboot-bootloader), must be waiting for response from device
* reboot your phone
* if you are lucky enough the command will be accepted on load.
Click to expand...
Click to collapse
Can you please tell me where to run this Command? I'm a noob sorry. :/
ManishByatroy said:
Can you please tell me where to run this Command? I'm a noob sorry. :/
Click to expand...
Click to collapse
This command has to be run on a computer.
Similar as you are running fastboot commands to root phone or install custom recovery.
Please google if you are not familiar with fastboot commands at all.
Make sure you have installed proper phone usb drivers to make your phone "visible" from computer.
Btw how did you get running Ignorance?
kvestas said:
Did you try fastboot command to reboot into bootloader?
The command might be accepted by phone during it's initial loading stage:
* connect phone to a computer
* run command (e.g. fastboot reboot-bootloader), must be waiting for response from device
* reboot your phone
* if you are lucky enough the command will be accepted on load.
Click to expand...
Click to collapse
kvestas said:
This command has to be run on a computer.
Similar as you are running fastboot commands to root phone or install custom recovery.
Please google if you are not familiar with fastboot commands at all.
Make sure you have installed proper phone usb drivers to make your phone "visible" from computer.
Btw how did you get running Ignorance?
Click to expand...
Click to collapse
My friend got ignorance running for me.. Like I don't know what and where to enter these fast boot commands.. Any link to learn or you explaining will be appreciated.
phone is blank. hasnt lighted a pixel in a week
phone is charged. how do i know this? because i charged it for 3 days :3
tried all combinations of buttons to get to bootloader. i just cant!!!
i connect it to a comp, it connects and disconnects simultaneously.. :/
pls tell me what to do
ManishByatroy said:
phone is blank. hasnt lighted a pixel in a week
phone is charged. how do i know this? because i charged it for 3 days :3
tried all combinations of buttons to get to bootloader. i just cant!!!
i connect it to a comp, it connects and disconnects simultaneously.. :/
pls tell me what to do
Click to expand...
Click to collapse
You may download and try this tool:
http://forum.xda-developers.com/showthread.php?p=46202420
This might be easier to start from.
kvestas said:
You may download and try this tool:
http://forum.xda-developers.com/showthread.php?p=46202420
This might be easier to start from.
Click to expand...
Click to collapse
Just tried it. I selected device but stuck on downloading drivers
Thanks for the help tho mate
ManishByatroy said:
Just tried it. I selected device but stuck on downloading drivers
Thanks for the help tho mate
Click to expand...
Click to collapse
You can download HTC drivers from almost any other hOV thread.
Like this one in example:
http://forum.xda-developers.com/showthread.php?t=1996665
Basic Requirements. 4th item.
Remember, all you need to try with this tool is to reboot into bootloader. Try to click the tool button while your phone is starting to load.
By the way, you may find fastboot files in that thread as well (Basic Requirements. 5th item).
kvestas said:
You can download HTC drivers from almost any other hOV thread.
Like this one in example:
http://forum.xda-developers.com/showthread.php?t=1996665
Basic Requirements. 4th item.
Remember, all you need to try with this tool is to reboot into bootloader. Try to click the tool button while your phone is starting to load.
By the way, you may find fastboot files in that thread as well (Basic Requirements. 5th item).
Click to expand...
Click to collapse
Yes, I have the HTC Sync installed which gives the necessary drivers for the recognition of HTC phones.. ( My ONE V)
But, the computer just sounds that music when a USB device is connected, the phone is dead. Not even lighting up..
The WinDroid isn't recognizing my device as well..
ManishByatroy said:
Yes, I have the HTC Sync installed which gives the necessary drivers for the recognition of HTC phones.. ( My ONE V)
But, the computer just sounds that music when a USB device is connected, the phone is dead. Not even lighting up..
The WinDroid isn't recognizing my device as well..
Click to expand...
Click to collapse
The computer should not recognize your phone because it is not loaded completely (neither os, neither recovery).
But it might be recognized for a few seconds only while trying to load os. And you might be able to supply reboot command at that particular moment.
Just try what I said.
kvestas said:
You may download and try this tool:
http://forum.xda-developers.com/showthread.php?p=46202420
This might be easier to start from.
Click to expand...
Click to collapse
kvestas said:
The computer should not recognize your phone because it is not loaded completely (neither os, neither recovery).
But it might be recognized for a few seconds only while trying to load os. And you might be able to supply reboot command at that particular moment.
Just try what I said.
Click to expand...
Click to collapse
Yeah.. I tried that.. But nothing is working.. The OS too isn't booting up. So I don't really know when my phone is on or off
ManishByatroy said:
Yeah.. I tried that.. But nothing is working.. The OS too isn't booting up. So I don't really know when my phone is on or off
Click to expand...
Click to collapse
Do you mean led is always off?
---------- Post added at 04:17 PM ---------- Previous post was at 04:14 PM ----------
Try holding power button down for 30s.
kvestas said:
Do you mean led is always off?
---------- Post added at 04:17 PM ---------- Previous post was at 04:14 PM ----------
Try holding power button down for 30s.
Click to expand...
Click to collapse
Tried. Ain't working. LED ain't even turning on while charging too.. So there's really no way to find out whether it's charging..
Update : Still haven't fixed my phone. Any help would be appreciated. Can't enter Bootloader menu. Phone when connected to computer, gives "sound" that every normal USB when connected gives.. So the phone isn't completely dead. After connecting, the computer doesnt react in any way :crying:
My One Plus 3 managed to delete its own Operating System, USB Debugging wasnt enabled, the Bootloader is not unlocked, its not rooted either and I dont have a custom recovery like TWRP installed. I tried to flash it wtih the adb console commands but it stops at some percentage and the device says that the installation failed (tried this with cm, oxygen and pacman). I tried to install TWRP over fastboot but cant manage it because USB Debugging isnt activated. I dont know what to do and need help
PS: Hope this Post is in the right thread
SolomonOdonkah said:
My One Plus 3 managed to delete its own Operating System, USB Debugging wasnt enabled, the Bootloader is not unlocked, its not rooted either and I dont have a custom recovery like TWRP installed. I tried to flash it wtih the adb console commands but it stops at some percentage and the device says that the installation failed (tried this with cm, oxygen and pacman). I tried to install TWRP over fastboot but cant manage it because USB Debugging isnt activated. I dont know what to do and need help
PS: Hope this Post is in the right thread
Click to expand...
Click to collapse
bro, do you even google?
http://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700
bombaglad said:
bro, do you even google?
http://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700
Click to expand...
Click to collapse
I did but didn't found that thread, but thanks mate
SolomonOdonkah said:
I did but didn't found that thread, but thanks mate
Click to expand...
Click to collapse
that is literally the first thing on the list if you google "oneplus 3 unbrick" but i'm glad i helped, that thread saved my ass several times already
Hello. I can't seem to access recovery mode after I flashed LineageOS 14.1 on my Asus Zenpad 8 Z380KL. I've tried to access the recovery mode by pressing volume up + power button together when restarting my device and by trying via command prompt to no avail. Both methods can give me access to recovery mode when I'm still using the stock Android. Because of this, I can't access TWRP. Can someone help me? Thanks in advance!
knightofzealot said:
Hello. I can't seem to access recovery mode after I flashed LineageOS 14.1 on my Asus Zenpad 8 Z380KL. I've tried to access the recovery mode by pressing volume up + power button together when restarting my device and by trying via command prompt to no avail. Both methods can give me access to recovery mode when I'm still using the stock Android. Because of this, I can't access TWRP. Can someone help me? Thanks in advance!
Click to expand...
Click to collapse
Settings about phone press build number several times to activate developer settings
Settings developer options activate advanced restart
Long press power restart recovery
kurtn said:
Settings about phone press build number several times to activate developer settings
Settings developer options activate advanced restart
Long press power restart recovery
Click to expand...
Click to collapse
Thanks for replying. I'm sorry it took me such a long time to respond, clinical rounds really do take your time and overall life away
:crying:
I've tried that method but it does not work. All it does was a normal reboot even after I choose the recovery reboot option.
knightofzealot said:
Thanks for replying. I'm sorry it took me such a long time to respond, clinical rounds really do take your time and overall life away
:crying:
I've tried that method but it does not work. All it does was a normal reboot even after I choose the recovery reboot option.
Click to expand...
Click to collapse
You pushed recovery radio button, OK, and rebooted into LOS system? Then you should fastboot flash recovery.IMG. ..can you boot into bootloader?
No, choosing the bootloader option also does only normal reboot
knightofzealot said:
No, choosing the bootloader option also does only normal reboot
Click to expand...
Click to collapse
Last chance : connect to a computer and type adb reboot bootloader
hi i have the same issue on sony xperia m2 with lineage os 14.1 ( all the same ) cant acces to recovery and with "fastboot boot recovery.img" i just get the sony logo....
OR .....
knightofzealot said:
No, choosing the bootloader option also does only normal reboot
Click to expand...
Click to collapse
Assuming you have root access, install the "Flashify" app and if it will not let you reboot into recovery, you likely need to re-flash the recovery image. :fingers-crossed: You may have already tried this approach, but if not, it has worked for me in the past when all else has failed.
And yes, clinical rounds do get in the way, but it is not as if you can tell them to wait.
kurtn said:
Last chance : connect to a computer and type adb reboot bootloader
Click to expand...
Click to collapse
No, it doesn't work either
nezlek said:
Assuming you have root access, install the "Flashify" app and if it will not let you reboot into recovery, you likely need to re-flash the recovery image. :fingers-crossed: You may have already tried this approach, but if not, it has worked for me in the past when all else has failed.
And yes, clinical rounds do get in the way, but it is not as if you can tell them to wait.
Click to expand...
Click to collapse
Haha seriously, being a medical student really suck your time away. I'll try this. Thank you!
@knightofzealot, I know that this doesn't answer your question specifically but, I just wanted to let you know that the following is the Enhanced Tag link that's specific to your device.
https://forum.xda-developers.com/t/asus-zenpad-8
It's just the first step for this device to get its own Device Dedicated area on the forum.
Good Luck!
~~~~~~~~~~~~~~~
I DO NOT provide support via PM unless asked/requested by myself. PLEASE keep it in the threads where everyone can share.
Have you solved? Same problem on xperia z1 compact
Have the same device.
Bootloader mode doesn't work either and seems like there is no way to unlock it. Because of this I can't operate with tablet using adb fastboot.
Having Same Issue
I am having same issuee. I flashed Lineage OS 15 using TWRP on Lenovo Vibe K5. Now I'm unble to access recovery mode or TWRP. I'm just seeing the lenovo logo.
knightofzealot said:
Hello. I can't seem to access recovery mode after I flashed LineageOS 14.1 on my Asus Zenpad 8 Z380KL. I've tried to access the recovery mode by pressing volume up + power button together when restarting my device and by trying via command prompt to no avail. Both methods can give me access to recovery mode when I'm still using the stock Android. Because of this, I can't access TWRP. Can someone help me? Thanks in advance!
Click to expand...
Click to collapse