Develop Bugs

[APP] [UPDATED 9/27/2011]V1.9 Working App to Backup Windows Phone 7 via ZUNE ANY TIME

I have written a .Net app for backing up windows phone 7 via the Zune updater tool. This backup can be used by Zune to restore the device when you use the "Update" option under settings.
This is a COMPLETE backup and COMPLETE restore IF USING ZUNE 4.7AND/OR the V1.9 Tool. Your phone will be EXACTLY the same after a restore as it was when you did the backup. Any updates, file changes, registry entries, or texts will not persist that were not on the phone at the time of the backup. Sorry for the bold but I have answered this question about a dozen times in PM's or on here.
Use this at YOUR discretion. There are scenarios in which you can't use the backup you made to restore. For instance on my Samsung Focus I had the stock ROM on it and couldn’t' restore my 7720 Mango backup. I had to upgrade the phone to at least 7712 Mango BEFORE the backup would restore. But I could go from 7720 to stock. When it failed I was getting a "Version Mismatch" error. Make sure you can at least get back to the REV level you backed up from before expecting this to work or you may be sorry. Finally, NEVER trust a backup that does not say it completed properly INCLUDING a SUCCESS message!!. I also HIGHLY recommend having a stock ROM on hand to flash back to the device if necessary.
HD2 owners: See Post 2 in this thread
**New features:
Manage backups/archives. Set Paths to zune and updatewp as well as the PKS file.
Archive capability of the older backups AND restore of active backup or archives.
Will Install Support Tools and PKS file if needed.
Version 1.8 will seem quite different if you are on Vista/7 with UAC and not running as a full admin. The reason is that you can't change registry entries in HKLM or move files in program files without those rights. If you werent running as a full admin before you may have trouble if you start now. Just answer the UAC prompts when a backup starts and ends to change the files/reg entries to 4.7 and back to 4.8 values/files. I tried to consider lots of conditions like what if it fails during the backup or crashes so if you launch the app after a crash it will detect that that the changed reg entries are in place and undo them to get you back to where you were prior to the last run. The UAC prompts are there to protect you so don't get mad at me when you see 2 each time you use this to backup. If you need ZuneWMDU.DLL from 4.7 check these posts attachments:
Click here for x86 (32 BIT) os's
or Click here for x64 (64 bit) os's
You can put it with the back tool or anywhere and the program will ask you where it is and you can tell it. You can even rename it to something else. For instance I have it in my Zune folder named Zunewmdu.dll.47. Just don't replace the original 4.8 Zunewmdu.dll file.
Firstly I have to credit this to reading and putting together pieces from several threads on XDA. I read so many to be honest I am no longer sure who all to credit. There was no specific single source I just saw several things and through trial and error put together the pieces that made this possible.
This APP is a wrapper around a tool microsoft produced to perform updates to your phone via command line. Specifically the executeable "updatewp.exe" that comes from the Windows Phone Support Tools. The missing piece that eluded me for a bit was the update package itself which I found here on XDA and will link to later.
Prerequisites that need to be Installed/downloaded:
Looks like at least Phone OS version 7008 is required for the backup to work.
Zune Software Installed (I'm sure most of us have this): http://www.zune.net/en-us/products/software/download/default.htm
Windows Phone Support Tools Installed - MS Links are dead ATM.
If you are missing these prerequisites the app will tell you and even open a web page on request to the DL links.
If an error occurs you should find the text in your clipboard for easy pasting here on the forums.
To explain the process:
updatewp.exe is meant to update your phone with PKS files theoretically obtained from the device manufacturer. It will also do other things including a command line restore of a backup.
This program launches updatewp.exe with two command line arguments. One is the PKS file name and path and the second is the enablebackup switch.
What happens is the phone performs the backup first, once it completes the process the code terminates updatewp.exe before it goes further. In theory if you are using an update not compatible for your phone it would actually just say that and quit. However terminating the updater keeps it from ever getting that far.
I have used this to make a complete backup AND restore it via the ZUNE Update options under settings for my phone so I know it works.
How to use the app:
Attached to this post is a zip file with two folders. x86 and x64. Please launch the appropriate EXE for your platform.
If you do not have zune or windows phone support tools it will tell you immediately and offer to open the download URL on your computer.
If you pass those tests you will need to input a path to the PKS file in the long textbox. There is a button just above it that will open a URL to the download for the one I used here on XDA. There is also a Browse button below the textbox for you to use to browse to and set the file path via GUI.
Once the path is set click on backup and watch it go. If you already have a backup made previously this will overwrite it or offer to archive it (v1.2 & up).
Good luck and post feedback, thoughts or issues please.
Changelog:
v1.9 - I pulled 1.8 and have added 1.9. This version corrects some more bugs in 1.8, one of which doesnt show the completed success message when performing a backup. The first time you launch it you will see a prompt stating this is the first time you have launched this version and you need to choose if you want to use the 4.7WMDU file switching method or just have the program try to use what you have installed. If you choose not to use the file switching method it will still check to make sure the zune and updatewp versions match but will only warn you they don't match, you can still try to proceed with the backup/restore. I have tested this in both modes doing backups and restores (this is why it took so long to get out).
v1.8 - I changed the way the program does things so that it will use the ZuneWMDU.DLL file from Zune 4.7 to perform FULL backups. You CAN'T use the tool without that file and I am not going to include it because I am not going to redistribute Microsofts property. If you are using Vista/7 with UAC you will be seeing some extra prompts because elevation is required to change reg entries and move files around to allow you to use this with the newest Zune 4.8 and still get a complete backup. To get the older ZuneWMDU.DLL file just get it from the install path of zune and then uprade to 4.8. The program will ask you for the path to the old DLL for future use/reference. Don't get pissed at me with all the UAC prompts either, they are required if you arent a full admin on the machine. I re-released 1.8 on 9/16 to fix a few minor bugs that kept it from working correctly under certain cirumstances.
v1.7 -PULLED because the backups Zune 4.8 Makes are utterly USELESS. 1.8 is in the works that will make use of the old updatewp and some old zune 4.7 files to perform COMPLETE backup and restores as it originally did.
v1.6 - Added the ability to set all of the paths (requested by folks using languages other than english). Added some management capabilities for the backups. To archive the active one immediately or move an archived backup to the active folder.
v1.5 - This only adds proper path support for windows XP. If you are using the 1.4 version and don't have XP then there is no need to upgrade.
v1.4 - Works with Mango Beta if you have updated Zune assuming you have also updated the 4.8 support tools. It will check the versions and inform you of any issues found. Also corrected the blank error message issue some users were seeing. 4.8 support tools, check the second D/L (non) link: http://forum.xda-developers.com/showthread.php?t=1148123
v1.3 - Changed the path used for backup location to the LOCALAPPDATA environment variable rather than USERPROFILE to be more compatible with XP. If you don't have the windows phone backup tools installed the software will offer to DL and install them silently for you. The PKS file is now packed in with the software. If you don't have a PKS file set it will offer to unpack it and use it by default. I didnt add ZUNE install to this because well, if you don't have that your not really using your phone are you?
v1.2 - Added archive capabilities. If you choose to backup your device and a backup is in place you are asked if you want to archive it. If you choose to keep it then a folder in your documents called "Windows Phone 7 Zune Backup Archive" is where it goes. Each backup will go in to a folder labeled by the date/time it was created. The format will be Month-Day-Year Hour-Minute-Second so you know exactly from WHEN the backup was from.
Added a Restore Button that will use the latest restore if that is all you have, or ask if you want to browse and choose from the archived backups to restore. Whichever you choose will become the "Active" backup to zune and then the restore will take place afterwards. The former active backup is automatically placed in the archive. When the restore is completed the SAME backup you chose is still the active one so using ZUNE to do the restore will yield the same result.
***IF you have multiple devices the archive portion will work fine, however I have yet to find a way to identify which ID is which device so when you choose to restore from an archive YOU will have to pick the correct one or it won't work.
v1.1 - Updated where the code looks for the windows phone tools to accomidate installs of zune to alternate locations.
In Development:
Determine the device ID of the connected phone so I can keep multi device backup archives straight when presenting which backups from an archive to restore. I don't have two devices so this will be a feature in beta until it is proven by your feedback.

Error Code Troubleshooting:
Firstly, if you want help in this thread PLEASE tell us what your Computer OS is including if its 32/64 bit. What OS revision your phone is at and What kind of phone along with details of the problem! Thanks!
I found this link to MS for different error codes and a solution grid of sorts that relates to ZUNE etc..:
http://support.microsoft.com/kb/2484484#80072EE7_801812DD_801811C5
This is a COMPLETE backup and COMPLETE restore IF USING ZUNE 4.7!!. Your phone will be EXACTLY the same after a restore as it was when you did the backup. Any updates, file changes, registry entries, or texts will not persist that were not on the phone at the time of the backup. Sorry for the bold but I have answered this question about a dozen times in PM's or on here.
ZUNE 4.8 seems to only backup whatever Zune does not synch and things like game states! I HIGHLY recommend reverting to 4.7 zune and phone tools if you want a COMPLETE backup. Zune 4.7 cant talk to Mango but it doesnt need to for a backup. A Complete backup made by 4.7 tools WILL restore with 4.8 tools.
Known Issues:
HD2 owners. There seems to be a problem using this method to backup the phone. The current theory is that the HD2 does not use the same boot loader as other WP7 devices and is not recognized correctly in that mode so it doesnt work. I would be interested in knowing how your updates are applied as the log I got from one user indicates the phone talked to the update program once it rebooted?!
Additional tips and observances:
*You CAN'T change the memory size and perform a restore, I already know this doesnt work so forget about adding memory and just restoring
*To my knowledge you can't backup from one device and restore to another as the backup files are signed/ID'd to the device that made the backup.
How to restore a backup via ZUNE if you don't want to use the restore feature:
Make sure your phone is hooked up to the computer first then from within the ZUNE software you should see a menu near the top right-hand side labeled "Settings". Click on that. On the settings screen look near the top left and you should see "Software" "Device" and "Account". Instead of device it may say "Phone".
Click on Device or Phone, whichever you see. The left edge has several options. Near the middle you should see "Update". Click that. You should see a progress bar for a few seconds and then most likely it will tell you that the phone is up to date. At the BOTTOM of all the text it spits out should be a button labeled "Restore" with the date of the backup.
BACKUP CREATION LOCATION:
Copy & paste the following in to the run dialog box:
Vista/Win7: %LOCALAPPDATA%\Microsoft\Windows Phone Update
Win XP: %USERPROFILE%\Local Settings\Application Data\Microsoft\Windows Phone Update
If you are running the backups with elevated privileges then you need to open a command prompt with those same privileges and paste in the above paths to find them as they may likely be in a different user account.
You will have to manuall drill down from their because the sub folder structure is named from the Phones ID.
Manual Command Line Method to Perform Backup:
All the same prerequisites apply. Zune and the windows phone support tools need to be installed.
It is easiest to have unzipped the PKS file in to folder the support tools are in. You can do this by opening the run dialog and typing: %PROGRAMFILES%\zune and hit enter or click ok. This will open explorer to that folder and you can move/copy the UNZIPPED PKS file there.
Open a command window with admin privileges. To do this in windows Vista/Win 7 with UAC enabled click on the "Start" Windows logo usually found in the bottom left corner.
In the search programs and files dialog type CMD and wait for the search to produce CMD.EXE at or near the top of the list. RIGHT click on cmd.exe and choose "Run as administrator". (hopefully you don't have to input admin credentials to do this)
At the command prompt type: cd %PROGRAMFILES%\zune (and hit enter). Your prompt should change to include the program files path and ZUNE for example "c:\progam files\zune"
Now assuming the support tools are installed correctly you can test by typing: updatewp (and hit enter) this should spam the screen with the command line options for updatewp and lets us know the rest will work.
The command to type is: updatewp.exe /iu A0CE706D-12B7-45AC-A5FC-AD04DFCA6E86.100.pks /enablebackup (and hit enter) You should be able to copy the command line as it is and right click on the DOS window at this point and choose "Paste" to save the trouble of typing that awefull string.
This is all the program I wrote does to start a backup other than kill the update process at the end since it can't happen.
I hope this works for you if the code does not!

Great!! thanks , will try .

The system cannot find the file specified
What precedes this section of the file path? and is it the same path on Windows 7?
/Library/Application Support/Windows Phone 7 Connector/Cache/Device Update/

Looks like your trying it on a Mac? Not gonna work
You can do it manually. Double check the updatewp.exe command line for a mac and if its the same as a PC then run it updatewp.exe PKSFILEPATH /enablebackup

hx4700 Killer said:
Looks like your trying it on a Mac? Not gonna work
Click to expand...
Click to collapse
I'm not. i'm on PC.

Where do i place the file from this page?
http://forum.xda-developers.com/showpost.php?p=11542700&postcount=6

I put it in the Zune folder and then my command line was:
updatewp.exe /iu "C:\Program Files\Zune\A0CE706D-12B7-45AC-A5FC-AD04DFCA6E86.100.pks" /enablebackup
open cmd.exe to the dos prompt and change to the ZUNE folder and then type or copy & paste in the above.
Perhaps I didnt specify this but you will need to unzip that file from the other post.

hx4700 Killer said:
I put it in the Zune folder and then my command line was:
updatewp.exe "C:\Program Files\Zune\A0CE706D-12B7-45AC-A5FC-AD04DFCA6E86.100.pks" /enablebackup
open cmd.exe to the dos prompt and change to the ZUNE folder and then type or copy & paste in the above.
Perhaps I didnt specify this but you will need to unzip that file from the other post.
Click to expand...
Click to collapse
Sorry, but I'm not quite sure what you mean :-/
I unzipped the "A0CE706D-12B7-45AC-A5FC-AD04DFCA6E86.100.pks" file
Then, I placed it in the zune folder: C:\Program Files\Zune\
Now I have cmd open, but I don't know what you mean by "change to the ZUNE folder and then type or copy & paste in the above."
What do I change about the Zune folder? and what am I typing into the cmd promt?

when I say change to the zune folder I mean change the current folder the command prompt is at by typing this:
cd c:\program files\zune and press enter
copy the following text in to the clipboard:
updatewp.exe /iu "C:\Program Files\Zune\A0CE706D-12B7-45AC-A5FC-AD04DFCA6E86.100.pks" /enablebackup
Then right click on the command box and choose paste and hit enter.
OR just type the above text in to the command box and hit enter.

Well, I got a little further, but I get this message in the cmd:
c:\Program Files\Zune>updatewp.exe "C:\Program Files\Zune\A0CE706D-12B7-45AC-A5FC-AD04DFCA6E86.100.pks" /enablebackup
'updatewp.exe' is not recognized as an internal or external command, operable program or batch file.

There was a prerequisite you needed that I listed. It is the windows phone support tools:
Windows Phone Support Tools:
x64 Windows: http://download.microsoft.com/downlo...Tool-amd64.msi
x86 Windows: http://download.microsoft.com/downlo...rtTool-x86.msi
updatewp.exe comes from that and is installed in to the zune folder when you install those tools.

Nice. Got the backup to work! Thanks for all the help. I'm going to hard reset and see if the backup works

quick question: does the backup process backup everything, including word documents?

The backup seems to backup anything on the phone.
For instance I used the reg hacks so I could see the phone in explorer. I put a couple of files in the video folder directory as a test and the phone could play them.
Further Zune ignored them and did not consider them as part of the sync process.
When I performed by backup and restore even those files were restored.
I can not speak to folders created that are not part of the normal hierarchy but I suspect that anything on the phone is backed up.
Adding:
I should stress again that this is the same backup that zune performs when you update your device with the update tool. This is just using one of the support tools that offers command line to trigger the backup when you have a legitimate update file. In this case however the program I wrote is terminating the update before it can begin once the backup is performed. So in other words I am just "tricking" the update program in to running and performig the backup.

Mallux,
I just figured out why you were getting that error.
The code checks for the existance of zune and then the support tools specifically by checking for the existance of the files.
The checks do the same thing so I cut & paste the zune check code in for the support tools and didnt change the path to check for updatewp.exe. So basically the code checked for zune twice and then went on.
I fixed the code and updated the DL link in the first post.
Im sure now that you have the support tools installed the code would work as written, or with the new DL link.

Hi and congrats for your work (if it works ? hehe, just kidding).
Maybe you would have better feedback in posting this to the dev and hacking section or the software one ?
Just a thought, since here are mostly apps for the phone itself.
Best regards
Andy

[APP] Working App to Backup Windows Phone 7 via ZUNE ANY TIME
I posted this in windows phone 7 apps and it was suggested that I post it here so don't hammer me for cross posting please.
I have written a .Net app for backing up windows phone 7 via the Zune updater tool. This backup can be used by Zune to restore the device when you use the "Update" option under settings.
Firstly I have to credit this to reading and putting together pieces from several threads on XDA. I read so many to be honest I am no longer sure who all to credit. There was no specific single source I just saw several things and through trial and error put together the pieces that made this possible.
This APP is a wrapper around a tool microsoft produced to perform updates to your phone via command line. Specifically the executeable "updatewp.exe" that comes from the Windows Phone Support Tools. The missing piece that eluded me for a bit was the update package itself which I found here on XDA and will link to later.
Prerequisites that need to installed/downloaded:
Zune Software Installed: http://www.zune.net/en-us/products/software/download/default.htm
Windows Phone Support Tools Installed:
x64 Windows: http://download.microsoft.com/downl...E4A-8179-9A3C5483E366/WPSupportTool-amd64.msi
x86: http://download.microsoft.com/downl...-4E4A-8179-9A3C5483E366/WPSupportTool-x86.msi
An update package from ANY phone, this one is for an HD2 that I used while working on a samsung focus. Download and Unzip:
http://forum.xda-developers.com/showpost.php?p=11542700&postcount=6
If you are missing these prerequisites the app will tell you and even open a web page on request to the DL links.
Please understand this is release 1.0 and as such may have issues depending on your platform and your computer etc.... I coded it for x86 and x64 Windows with the Microsoft .net Framework 2.0 minimum. I tried to consider several error scenarios but one never knows how an end user might use your program that wasnt anticipated and coded for.
If an error occurs you should find the text in your clipboard for easy pasting here on the forums.
To explain the process:
updatewp.exe is meant to update your phone with PKS files theoretically obtained from the device manufacturer. It will also do other things including a command line restore of a backup.
This program launches updatewp.exe with two command line arguments. One is the PKS file name and path and the second is the enablebackup switch.
What happens is the phone performs the backup first, once it completes the process the code terminates updatewp.exe before it goes further. In theory if you are using an update not compatible for your phone it would actually just say that and quit. However terminating the updater keeps it from ever getting that far.
I have used this to make a complete backup AND restore it via the ZUNE Update options under settings for my phone so I know it works.
One could most likely also archive backups by copying/moving from their storage point before creating a new one so as to have a backup that could be reverted to from a point in time further than the last one on record. If there is enough interest in such a feature and incentive I would consider adding it here.
Attached to this post is a zip file with two folders. x86 and x64. Please launch the appropriate EXE for your platform.
If you do not have zune or windows phone support tools it will tell you immediately and offer to open the download URL on your computer.
If you pass those tests you will need to input a path to the PKS file in the long textbox. There is a button just above it that will open a URL to the download for the one I used here on XDA. There is also a Browse button below the textbox for you to use to browse to and set the file path via GUI.
Once the path is set click on backup and watch it go. If you already have a backup made previously this will overwrite it.
I can not say if this will work with a debranded phone but I don't see why not. My focus is an out of the box stock AT&T phone with chevron unlock on it (which you shouldnt need) and a couple of non-marketplace apps.
Good luck and post feedback, thoughts or issues please.
***Adding Instructions on how to restore as its come up a few times:
Make sure your phone is hooked up to the computer first then from within the ZUNE software you should see a menu near the top right-hand side labeled "Settings". Click on that. On the settings screen look near the top left and you should see "Software" "Device" and "Account". Instead of device it may say "Phone".
Click on Device or Phone, whichever you see. The left edge has several options. Near the middle you should see "Update". Click that. You should see a progress bar for a few seconds and then most likely it will tell you that the phone is up to date. At the BOTTOM of all the text it spits out should be a button labeled "Restore" with the date of the backup.
You CAN'T change the memory size and perform a restore, I already know this doesnt work.

Ok first off all, I have to thanks for you for your hard work! The tool just worked like a charm. I just used the back-up tool and it succeeded made a backup of my Omnia 7. I'm just wondering a few things:
Is my phone identical the same if I use the backup tool? That means the register changes and installed apps??

I have used the zune update - Restore function and everything was the same. I have several xbox live games and after the restore I was still at the same place in my games. Further my phone is chevron unlocked and remained so after the restore.
Further, I did the reg hacks to see the phone in explorer when zune is closed and put a couple of small vid files in the video folder. Those files did not show up in Zune on my PC or in my collections but the phone could play them just fine. After the restore they were still there too. So from what I can tell the une backup tool backs up the phones memory as it is no matter what is there. I have not tested non-standard folders that are user created though but would assume they would work all the same.
Further a couple of observations:
During development I found I could unplug the phone at any time during the backup process and it would be just fine. No harm.
In Zune when the phone is hooked up I could see the "memory graph" and it had slices in it and hovering over them with the mouse would yield what each slice was... e.g. Videos, Music, pictures etc... I had a large area that said it was reserved for data "from another computer" or some such verbiage. After the restore that was gone and I had a little more memory back for my own use. The slices seemed to be gone too but had no effect on what zune synched etc... Perhaps a full resynch might change it but I havent done that.
**Adding:
Having re-read your post I am now wondering if you are asking if your phone is the same as after the backup as it was prior to the backup? It should be unchanged. The backup process is the same that would occur if you were performing a legitimate carrier update. The process says it transfers the update to the phone but does not execute it until after the backup. My code terminates the updatewp.exe program before that happens so ultimately you might have the 310k file still on your phone in some "updates" folder somewhere.

[XAP][SOURCE][ROOT] XapHandler (RELEASE for Root Tools or full-unlock!)

Hi folks,
FIRST RELEASE:
Wow, lots of bugs that needed fixing. There are still some things I'd like to improve, but they can wait. This is officially the first release of XapHandler, for stock ROMs with WP7 Root Tools, and optionally for custom ROMs as well.
INSTRUCTIONS:
1) Install XapHandler.
2) Run WP7 Root Tools.
3) Pivot to Policies, and set XapHandler as trusted (stock ROMs only).
4) Run XapHandler.
5) When prompted to set the file association, hit OK.
6) Exit XapHandler.
7) Open a XAP file from email, IE, or an app.
8) Check the data about the app given in XapHandler.
9) If the app is already installed and you want to do a clean install, exit XapHanderl and delete the app from your phone normally, then open the XAP file again.
10) Hit the Clean Install or Update button.
11) Wait for the Success message box.
12) Close XapHandler.
SOURCE CODE:
I don't have permission to release the actual XAP installation source code, which is from @ultrashot. Therefore, the source release just contains a pre-compiled static library (it's the same code as is used in the native XAP installer on custom ROMs, and the Bazaar app). You're able to build the full app, though.
The app has two parts: the native ARM DLL that has the COM library and does the actual installation, and the C#/Silverlight WP7 app that provides the UI and calls the COM library. You should unpack both parts to the same folder. Then, build the native part first (requires Visual Studio 2008 with the Windows Mobile 6.5 compiler). This will copy the native DLL into the managed app. Make sure the managed app includes the COM DLL, and then build it to produce a XAP file.
PROBLEMS:
If you have any issues, please report the following info:
A) Your phone model.
B) Your ROM (including version and firmware)
C) The problems or exception messageboxes you encountered.
RESTORING THE REGISTRY:
For stock ROMs, if you want to put the registry back the way it was so XAP files open in the built-in XAP handler of your custom ROM:
1) Open a registry editor
2) Go to HKEY_CLASSES_ROOT (HKCR)\.xap
3) Change the default value back to what it used to be
3.1) The original value on most custom ROMs should be "xapfile" which is the same value the app uses; don't panic if it's unchanged!
3.2) The old default value *should* be backed up in a registry value simply called "0"
4) If there's a value called 0, delete it
5) Go to HKCR\<originalClassName>
5.1) For most people, that's HKCR\xapfile
6) Change the default value back to what it used to be
6.1) The original value on most custom ROMs should be empty
6.2) This step is not important; the value is cosmetic and intended for the user
6.3) The old default value *should* be backed up in a registry value simply called "0"
7) If there's a value called 0, delete it
8) If you have a registry key called BrowseInPlace (eg. HKCR\xapfile\BrowseInPlace) you can delete it
8.1) I don't *think* it'll hurt anything if left, though
9) Set the registry value EditFlags to DWORD 65536 (0x00010000)
9.1) This value is set by release versions of XapHandler
9.2) If the value is missing, create it with the data listed above
10) Go into the registry keys "shell", "open", and "command"
10.1) For example, HKCR\xapfile\shell\open\command
11) Change the default value back to what it used to be
11.1) The default value on most custom ROMs should be "XAPDeployer.exe "%1"" (remove first and last quotes)
11.3) The old default value *should* be backed up in a registry value simply called "0"
12) If there's a value called 0, delete it
13) If you had to change anything in step 3, go to HKCR
13.1) Don't do this step if you didn't have to change anything in step 3!
14) Delete HKCR\xapfile and all its contents
14.1) This step isn't needed, just cleanup
14.2) Don't do this step unless you had a different original progID than "xapfile"!
Have fun!
Please feel free to include this app in WP7 homebrew collections or custom ROMs, so long as the Author attribution is not removed.
Total downloads of the test versions: 330.

Thank you my friend
big business

Big Thanks to useful reports, of course!
I'm also looking at releasing an app that allows people to edit their file associations on the phone - things like add new filetypes that will open in Word (works for any plain-text file), or do complex things like "open" a Mobi file by putting it in the Kindle app's isostore, then launching the Kindle app. That will build on some of the work done in this app. It's also related to some stuff for the next version of Root Webserver. I really want to figure out what's going on here, though...

a.) Samsung Focus v1.3
b.) My ROM (see sig) firmware 2124.11.9.4
c.) xapfile
d.) no change, errors: system.io.filenotfoundexception the system can not find the specified at xaphandler.xapdeployerinterop.setfileassociation() and so on and on then crashes to home screen
e.) reboot changes nothing, no other steps apply.

I installed with my hd2 program
program did not work
19.Marc HD2 Pdaimatejam Rom Wp7.5 Tango 7.10.8773.98 v7.8 >FULLY UNLOCKED>CABS Update

Mozart
5.13-based custom rom (fully unlocked of course)
FileNotFound exception when trying to associate, IndexOutOfRangeException when trying to launch xap (after manual association)

ultrashot said:
Mozart
5.13-based custom rom (fully unlocked of course)
FileNotFound exception when trying to associate, IndexOutOfRangeException when trying to launch xap (after manual association)
Click to expand...
Click to collapse
yes
I get the same error

Thanks, guys. I know where the error is for you - I took a shortcut testing for the existence of certain registry entries and didn't check for FileNotFound, which I should have. Expect a new version in a day or so!

do you mean use xapdeploy.exe to install a xap?

XapDeploy.exe can't be used on stock ROMs until we break the policy system to allow homebrew executables. This app runs under TskHost.exe, like any other executable. Using WP7 Root Tools v0.9, it should be possible to run this app on stock ROMs.
Additionally, it's an alternative to XapDeploy.exe for users of custom ROMs. It displays more info about the XAP before installing it - not enough in any way to prevent Trojan malware, but enough to stop you from accidentally installing v1.15 when you wanted 1.16.

Please do post test results for the second test version. I still can't get it working on my phone, but I want to know if it works on a full-unlock - if not, there's a bug in the app, but if so then the issue is in the way I elevate. Please give it a try!

gave the same error
version 2

GoodDayToDie said:
Please do post test results for the second test version. I still can't get it working on my phone, but I want to know if it works on a full-unlock - if not, there's a bug in the app, but if so then the issue is in the way I elevate. Please give it a try!
Click to expand...
Click to collapse
OOM exception while checking association, on minimizing-resuming it asks for associating (and does it correctly), but then SUCCESS on installation

except update
application tries to install
thanks

Now *that* is bloody weird; even without elevation the app gets further than that. This happens when you open a XAP file after associating the app with XAP files, right? (Was it really too much to ask that people actually provide a proper report?) There's only two places that the app uses GetResourceStream - one to open the XAP file, and one to open the manifest from within the XAP file.
I've made some changes to the app, which should make it more resilient to unexpected parameters and will hopefully help make the GetResourceStream calls less likely to fail. Please remove any manual file association you created for the app (set it back to the defaults) and run the test procedure again with the new test3 build (will be uploaded momentarily). The app was able to associate itself correctly on my phone starting with test2.
I'd also like to see this tried on some different custom ROMs. It *should* work but I still can't get the actual install to succeed on my phone (though it does get that far...).

@ultrashot: Wow, the OOM is weird and I haven't seen that in my testing, but hey, if it worked the second time... OK then! Thanks for the success report! Time to look into what level of unlock is required and figure out how to get it on a stock ROM, because elevating the app doesn't seem to be enough...

Hi GoodDayToDie, I am using HTC Gold with Dyanamic7 Rom. Firmware 51201.401. Have installed the XapHandlerTest2.xap and I am able to install Xap files which are stored in the device. Please let me know if you require any more details.

Can you do updates? I'm *sometimes* able to install an app that is not yet installed, but if the app is installed, either an update or a clean install always fails. Clean install seems more reliable immediately after rebooting the phone, but it still appears non-deterministic to me.
I hate Schroedenbugs... although HtcRoot seems to have a lot of them. I need to work on that some more.
Still, it's progress. Hopefully, by the time WP7 Root Tools 0.9 is out and the app can be used on more stock ROMs, it'll be fully working...

v3 test
except update
application tries to install
thanks

Where Internet explorer save the XAP? (I have a custom ROM (Omnia7))

[GUIDE][HAVE A LOOK] DONT KNOW SOMETHING? Check here first!

If you got ANY questions? Feel free to ask here..
[HELP THREAD]Any Questions? Anyone Can Ask here [GT-5360/5510/5512/6102]
VERY LENGTHY THREAD?? Difficult to read in app? Yes I know friends!! That's why added hide/spoiler button to each post & link to first post in every posts end
Hi, Everyone, This is a GUIDE to NEW / EXISTING users.. There are guides below for advanced users too.. So i have shared my experience at XDA with you all to make others understand and help each other.
If you want to know something/ want me to include a topic here, please PM me.. I will see if i can help with that and write about it.
Hopefully this will help many of you, Now READ ON.. Click On "SHOW CONTENT" Button to See the content on each posts below!
DIFFICULTY LEVELS: It tells you how much difficult it is for you to do the task described below. See the headings of guides in every post to see difficulty of that task.
* --> Very Easy
** --> Easy
*** --> Moderate
**** --> Difficult
***** --> Very Difficult​INDEX OF THIS THREAD:
* Abbreviations/Acronyms used in XDA (Android language) [SEE 2ND POST]
* Simple methods to get LOGCAT, DMESG [SEE 3RD POST]
* CWM MD5SUM mismatch error while restoring? Solution for this: [SEE 4TH POST]
* How to use SDCARD instead of internal storage for apps[LINK2SD] [SEE 5TH POST]
* Detailed steps to install Stock rom/Firmware through ODIN [SEE 6TH POST]
* ROM installations instructions [IN GENERAL] [SEE 7TH POST]
* Kernel installations instructions [IN GENERAL] [SEE 8TH POST]
* How to deodex a stock rom in easy way using DSIXDA Kitchen [SEE 9TH POST]
* USEFUL LINKS TO THREADS/GUIDES SECTION [SEE 11TH POST/1ST POST OF 2ND PAGE]​
MISCELLANEOUS: [SEE 10TH POST]
* Thread Title tags confusing? Its explained here!
* Why give "Thanks"? Thanks meter explained!
* Stars, User Titles: Junior, Member, Senior Member........? Read to know more!
* XDA/TAPATALK app image uploading problems??
* Make your Thread/Post Aligned(Neat) by using BBCODE TAGS
* Battery Drain?? Read these tips to avoid it.
* Enable Whatsapp *AUTO DOWNLOAD IMAGE OPTION* in new versions [TRICK]​
PLANNED GUIDES ARE:[12th POST]
How to make a kernel--Writing in progress
How to get 10 without spamming / complaining!!
How to modify apps background,looks etc.
CREDITS :
To all my friends and xda members who gave me info to learn about these things.
To anmolsharma1293, deathnotice01, jaison thomas, kidcarter93, lavadepa, MNgez, nikufellow, tjsgy, wcypierre who gave suggestions and info and tips to improve this guide.
To The-Captain our moderator for helping us to improve ourselves, learn more and being kind to new users too.
Credits are added to respective people in the posts related to them whenever i have taken info / used their work[if not done, i will do it soon]. Informations obtained from other threads have been added in the posts related to it and i have done it with the permission of the thread OP. If i have forgotten someone's name please do let me know, and i will add it ASAP..
And please tell me any suggestions to improve this guide to help newbies/noobs as this guide should help all of us to get better at things we can do with an android. PLEASE REPORT ME ANY MISTAKES IF I HAVE MADE IN WRITING THE GUIDE/ IF THERE IS A WRONG INFORMATION.. I WILL CORRECT IT ASAP..
If i missed anyones credit, please forgive me and let me know.. and i will add it as soon as i can, promise!
Thank you.

Abbreviations/Acronyms used in XDA (Android language)
The reason for this guide is that many new users would have difficulty to understand what are these short forms.. everyone says cwm, rom, cm, etc.. but no one says what it is.. and you may feel a bit shy/embarrassed to ask them what it is. So here is my attempt to cover them..
Please do let me know in PM if some words are missing and you want them to be covered.. i will gladly add them, thank you.
This Post is an inspiration from mrhaley30705's thread & Diablo67 thread.
Use CTRL+F to find a specific term.Difficulty --> *
XDA RELATED ACRONYMS
DEV: Developer
ERD: Elite Recognized Developer
FM/FSM: Forum Moderator/Forum Specific Moderator
RC: Recognized Contributor
RD: Recognized Developer
RT: Recognized Themer
SM: Senior Moderator
GENERAL
AFAIK: As Far As I Know
ATM - At the moment
BTDT - Been there done that
CRACK: The password / product key / license key illegally used for unauthorized usage are known as a crack of the software . Also please read the warning posted at warez meaning below. The same applies to cracks
ETA - Estimated time of arrival.. Note: Asking ETA in dev section is a big NO NO..!!
FTFY: Fixed that for you
FTW - For the win
FWIW: For what it's worth
FYI: For Your Information
IBTL/IB4L - In before the lock / In Before Lock
IDK: I Dont Know (Thats what it means and i am not saying i dont know about IDK!!)
IIRC - If I recall / remember correctly
IRC - Internet Relay Chat
LOL - Laugh out loud
NEWBIE: Someone who is new to this field/ forum and wants to learn how to do it rather than say "NOT WORKING! FIX IT!".
NOOB: Someone who is new and doesn't want to learn "HOW" its done, just want to "USE" the end product. So, please guys dont be a noob, be a newbie!
OP: Short for Original Poster, or the person who originally started the thread.
OT - Off Topic
PM: Short for Private Message. Allows users of XDA to send and receive non-public messages. Accessed from USER CP.
P.S: stands for Post Script. It is used when u wrote a message on a postcard and u forgot to mention an important information.*
ROFL - Roll on floor laughing
RTL: Right To Left support (In Some languages you have to start reading from right and end towards left side.. as against to usual method of reading from left to right)
SMH: Shake my head
STH: Something
TBH: To Be Honest
TIA: Thanks In Advance
THREAD: An individual issue page on the forum. This thing you're reading is a thread.
TLDR: Too long to read
TM: stands for Trademark.
USER CP: Short for User Control Panel. This button near the top of the XDA page allows users to update their avatar, personal information, and signature. PMs and subscribed threads can also be checked in this location.
WARES/WAREZ: Warez refers primarily to copyrighted works distributed without fees or royalties, and may be traded, in general violation of copyright law. To make it simple, it is any app/software which has to be paid to use them, but are used without paying any money.. PLEASE NOTE: THIS IS NOT TOLERATED AT XDA. SO PLEASE DONT POST WARES ANYWHERE ON XDA FORUMS. YOU WILL GET BANS/INFRACTIONS IF YOU DO SO!
ANDROID DEVICE RELATED:
ADB: Android Debug Bridge, a utility to run on a PC to allow connection to and control of an Android device. Part of the Android Software Development Kit (SDK), it allows for ROOT-level access to the Android device from a computer.
AOSP: Short for Android Open Source Project. The open-sourced code from which individuals can build new distributions of Android.
APK: An Android executable file, similar to the .exe file in Windows. Most programs will install with a .apk file.
Apps2SD:A method of storing applications and cache on the device's microSD card.
Bloatware: Software or 'apps' that you don't need, but come preinstalled to a device's /system partition, meaning that you cannot remove them unless the device has been rooted
Boot Animation: Boot animation is a term for a graphical representation of the boot process of the operating system. After you switch on / reboot phone you see this.
BOOTLOADER: There are two of these; the primary and secondary bootloaders. These programs tell the Android device how to start up, and are critical to its functionality.
Bootloop: When your system recycles over and over without entering the main OS.
BRICK/(HARD BRICK): An Android device that is completely non-responsive, i.e. nothing lights up, the screen does nothing, no combination of button presses cause any reaction. Can only be restored by JTAG or warranty service.
BUILD.PROP: A plain text file which contains environmental variables for the system to use during operation. Can be hacked to fake a different model for increased functionality, among many other operations. It is also used to make tweaks to boost speed/performance, etc.
BUSYBOX: An application that contains many standard Unix tools.
BUTTON COMBO/THREE BUTTON COMBO: The act of pressing several buttons at the same time to produce a desired result (e.g. press and hold volume up+home button+power button for 10 seconds will reboot into the RECOVERY menu at any movement when phone is on or Press and hold volume down+power button+home button to get into ODIN mode/DOWNLOAD mode).
Cache:A component that transparently stores data so that future requests for that data can be served faster.
CM: Short for CyanogenMod. CyanogenMod is an Android build built from the Android Open Source Project, and its builds are usable on multiple different Android Devices.
CPU: It stands for Central Processing Unit and handles all the complex mathematical formulas necessary to do everyday things like surfing the Internet.
CSC - File with Carrier Customizations
Custom bin counter: A line of code in several Samsung Galaxy devices' bootloaders that counts the number of times a user uses ODIN to flash ROMS/KERNELS to the device. Commonly used to detect software modification. This is called custom bin down in ODIN mode and it should be 0 to claim warranty. Can be reset with GALAXY TOOLBOX APP by Doky73
Custom: Independent developers who like to customize their devices beyond the standard options provided often tend to release the fruits of their labor for the rest to enjoy, in form of custom ROMs.
CWM: Short for ClockWorkMod Recovery Menu. This is a program that allows you to install custom ROMS/KERNELS as well as do many other customizations. Often referred to as the "RECOVERY MENU"/"CWM"
DALVIK CACHE: The collection of program information stored for use by the DALVIK program. This can be cleared from the RECOVERY menu to resolve issues with the Android OS.
DALVIK: The Android operating system's memory management tool. This program handles which other programs are running and assigns memory to them
DEODEXED: Removing the .odex files from an APK file. The .odex files contain a list of dependencies for the associated file, and if something changes, the .odex (and similarly, the associated file) not longer function correctly.
DMESG: dmesg (for "display message") is a command on some Unix-like operating systems that prints the message buffer of the kernel..
DOWNLOAD MODE: Read Button combo to know about this.
EFS: The directory /efs on the Android device's internal storage. Contains files with the Android device's IMEI, wireless devices MAC addresses, product code, and other information..
EMMC: Short for Embedded MultiMediaCard. A chip architecture consisting of an embedded storage solution with MMC interface, flash memory and controller, all in a small ball grid array package.
EXT4: A journaling file system (e.g. NTFS, FAT32 are file systems) often used by Linux distributions. Can be used with Android.
EXTERNAL SD: A micro SD card that has been inserted in the micro SD slot in the Android device. Can be removed.
FACTORY RESET: This will remove all user customizations in the Android OS, returning it to a factory state. Note: This will not wipe the Internal SD card. It will just make it as a phone just bought from the store state.
FC/FORCE CLOSE: When a program on the Android device becomes unstable/gets an error, the DALVIK program will force it to terminate to prevent further system instability which appears as a Force Close message usually in phone.
FLASHING: The act of writing code to the Android device. ROMs, MODEMs, KERNELs, and BOOTLOADERs can all be flashed. Independent from, and having nothing to do with, Adobe's Flash product.
FREEZE: Specific to LINK2SD/TITANIUM BACKUP. Using these 2 apps, the user changes a program into a non-functional, but still installed, state. Useful for identifying problem and FCs.
gapps - Google Applications, like GMail, Calendar, Maps, G+, etc
GB - Gingerbread, AKA Android OS 2.3.X
GOVERNOR: A program that interacts with the device hardware to increase or decrease the processor's clock speed (e.g. at low usage, it will set the processor speed to 400 MHz, but as usage increases, it would scale up to 1000 MHz).
HSUPA/HSDPA: Short for High Speed (Up/Down) Packet Access. This is 3G+, and is the Android device's internet speed level between 3G and 4G.
ICS: Short for Ice Cream Sandwich, the Android OS version 4.0.x.
IMEI: Short for International Mobile Equipment Identity. A unique number to identify GSM, WCDMA, and iDEN phones. Used by GSM networks to identify valid devices.
INTERNAL SD: The internal storage memory of the Android device. Not a physical SD card that can be removed.
JB: Short for Jelly Bean, the Android OS version 4.1.x.
JIG: A piece of hardware that makes a physical connection between pins of the USB slot to force the Android device into DOWNLOAD mode.
JTAG: A process of connecting directly to the main board of the Android device to rewrite corrupted BOOTLOADERS.
KERNEL: The kernel is a program that constitutes the central core of a computer operating system. It has complete control over everything that occurs in the system.
LAST_KMESG: last_kmsg is a dump of the printk statements from the kernel before the operating system itself crashed.
LAUNCHER: A program that launches programs in Android. Examples are Touchwiz (Samsung), HOLO Launcher, Launcher Pro, ADW Launcher, and Go Launcher EX.
LCD Density: Pixel density is a measurement of the resolution of devices in various contexts; typically computer displays, image scanners, and digital camera image sensors.
LOGCAT: A command to view messages in one of the system logs. See Android logger.
LTE: Stands for Long Term Evolution. It is based on the GSM/EDGE and UMTS/HSPA network technologies, increasing the capacity and speed using a different radio interface together with core network improvements.
MAI77 method: Its only known here. So dont say this out of SGY forum. This is a method to flash kernel through CWM using Kernel flasher tool made by MAI77. Its basically you have kernel flasher tool and boot.img file in SDCARD root and you select kernel flasher tool in CWM and it will install boot.img file which is the kernel you selected.
MD5 CHECKSUM: A 32-digit (128-bit) hash number generated by a cryptographic program to ensure that a downloaded file matches the original file. The original file is run through the MD5 generator program, which creates the 32-bit number. This number is checked against the md5 number created with the file the end user receives to ensure file integrity.
MIUI: A Chinese built-from-source ROM. Short for "Mobile Internet User Interface". Also can refer to the MIUI music player, which has been included in other ROMs.
Mod: The act of modifying a piece of hardware or software or anything else for that matter, to perform a function not originally conceived or intended by the designer.
MODEM: The software that interfaces with the phone's radio hardware to connect to cell phone towers.
NANDROID BACKUP: A complete system image backup of the Android device except for the MODEM and KERNEL. Can be accessed from CWM.
ODEX: A file that is associated with an APK file, containing a list of the dependencies for the program. See also DEODEXED.
ODIN: A Samsung proprietary program that allows the Android device to be flashed back to stock or with custom software.
OVERCLOCKING/OC: Setting the processor's clock speed to run faster than its default setting, i.e. 1248 MHz (1.2 GHz) vs 832 MHz (Default)
OTA - Over-the-Air (usually used as "OTA update" for firmware updates that can be installed directly via 3G/4G/Wi-Fi without the need of an PC)
PIT FILE: Short for Partition Information Table file. One of the possible file types used while flashing with ODIN or HEIMDALL.
Port: To Take a rom or app from one phone and program it to work on a different one.
Ram: (Random Access Memory) A group of memory chips, typically of the dynamic RAM (DRAM) type, which function as the computer's primary workspace.
RECOVERY: The menu that allows a user to do many low-level operations on the Android Device. This menu can either be the stock Samsung menu, or the CLOCKWORKMOD RECOVERY MENU (CWM). See also CWM.
RFS: A Samsung-proprietary file system (e.g. NTFS, FAT32 are file systems) used on some Android devices. Stands for Robust File System.
RIL - Radio Interface Layer
ROM: The collection of programs, themes, and settings that create the general look-and-feel of your Android device. This is what most users will initially be wanting to change. Or custom ROM firmware file, Can also refer to a Read-only memory.
ROOT: Changing the permission level of the Android system to its most powerful level, the root user, allowing full access to the file system. More like Administrator permission in Windows OS.
SGY /SGYD /SGYP /SGYPD : Samsung Galaxy Y / Samsung Galaxy Y Duos / Samsung Galaxy Y Pro/ Samsung Galaxy Y Pro Duos
Sideloading: It means installing applications without using the official Android Market.
SOFT BRICK: A device that is not functioning correctly, but still shows some signs of operation. See also BRICK.
STOCK: The Android software version that comes installed on new devices, prior to sale to the user. Can also be used to refer to the Android software issued from Samsung or the carrier.
Superuser/SU: On many computer operating systems, the superuser is a special user account used for system administration. Depending on the operating system, the actual name of this account might be: root, administrator or supervisor.
TETHER: Connecting the Android device to a computer via a wired or wireless connection to allow the transfer of data through the Android device's internet connection. Commonly used to provide internet access to a laptop or desktop computer when other methods are not desired or available.
THEME: A collection of images, backgrounds, colors, font types, and other visual items to change the Android device's look and feel. Separate from LAUNCHER, and is usually FLASHed in CWM.
TWRP2 - an alternate recovery mode for your phone
UNDERVOLTING/UV: Setting the voltage levels drawn by the Android device to a lower level to reduce overall battery usage.
Updater Script: When Android devices install updates via CWM/recovery mode they have to perform a wide range of functions on files and permissions. The scripting language is called Edify and is defined primarily in the bootable/recovery/{edify,edifyscripting,updater} directories of the Android source-code tree.
WCDMA: Short for Wideband Code Division Multiple Access. An air interface standard in 3G mobile communications networks that allows higher speeds and more users.
ZIPALIGNED: An archive alignment tool that provides important optimization to APK files. The purpose is to ensure that all uncompressed data starts with a particular alignment relative to the start of the file. Reduces RAM consumption.

Simple methods to get LOGCAT, DMESG
Devs asking you to get a logcat and give?? Yes it helps a lot for devs if you give logcat to solve problem. So dont wait till devs ask you to get a logcat! Just give them a logcat when you tell them this/that doesnt work. This way theirs and yours time will be saved and unnecessary posts will be avoided. Now i will give you simple steps to do it. There are two main ways to do a logcat, 1. within android device, and 2. through adb using PC.​WITHIN ANDROID DEVICE METHOD:
This i learnt from paxChristos from his thread.
1. Logcat within android device can be done in one of two ways, through a Logcat app: Difficulty --> *
Here are two good apps: aLogcat or Catlog
Both of these programs can dump their logs to a text file, which is very useful for debugging. Or, you can do it in terminal emulator (same rules as running through adb(see below))
2. Through Terminal method: Difficulty --> **
Install Android Terminal Emulator app from Play Store..
Open terminal app you just installed..
Enter these commands:
After every command press ENTER/SUBMIT button
Code:
su
then accept the superuser popup message[it comes only first time if you select checkbox "remember the choice"]
Code:
logcat -v long > /sdcard/test.log
Or use this command:
The -v long puts the text in a nice format that is more easily readable. The *:W will search for all warnings, errors, and fatals, while the *:S will silence everything else.
So essentially, u will have a .txt file that has a log of all warnings and up, nothing else, and it'll look pretty too!
Code:
logcat -v long *:W*:S > /sdcard/filename.txt
now press home button to minimize the terminal..
and do the task which is giving problems/ whichever task log you need to give to dev..
then drag the notification bar..
select terminal app in it..
now press and hold "Volume down button" and touch c button on keyboard.
This will stop the command..
now use this command twice
Code:
exit
Now app will get closed. go to sdcard to find test.log file.. upload it to here so that dev can access it..
Thank you for reading it with patience hope you can get logcat now..
Note: if you are stuck in boot and want to take logcat.. READ LOGCAT FROM ADB METHOD BELOW.. the above one is simple method for these tasks for eg.. if you are having some force close of app/lag etc.. then after entering second command press enter and then use home button to minimize terminal.. dont worry it will take log.. now open that app and once it gives force close then click on it and then open terminal again and press volume down button + c to terminate command.. then use exit command two times... done.. now go to sdcard and find a.txt file
From PC[i.e, ADB] LOGCAT METHOD :Difficulty --> ***
There is an advantage here. As doing this way, you can start using logcat when your device boots. There are 2 ways here again..
PREPARATION:
In your android device, go to settings --> applications --> development -->
Check USB Debugging
Make sure your device driver is already installed otherwise install kies software which will install drivers too.. Get kies from This LINK
You need to download this ADB.zip file i made to your system.. Download link
Extract the ADB.zip file from any applications like IZarc/7Zip/winzip/winrar.
ADB USAGE INSTRUCTIONS:
Then go to Android folder.. inside that you should find 3 files.. Now open a command prompt or terminal in that path..(wherever you extracted it.. use cd command)
Then inside that path.. type
Code:
adb logcat > filename.txt
Or
Code:
logcat -v long > /sdcard/test.log
Or
Code:
logcat -v long *:W*:S > /sdcard/filename.txt
Now perform tasks in android device of which you need to give logcat for the devs. Then use CTRL+C to end the command.
Now find the filename.txt inside the Android folder which has logcat. Upload this file and give link to dev..
Or There is another method called All in one logger tool by wcypierre which can get you logcat and dmesg. I have not tested it myself. But i am sure it will work and you can go to that thread and ask your queries about that tool if you want to use that. The dev will help you gladly. So, please thank him for his nice work.​The full list of options that can be used with logcat command is as follows:
V — Verbose (lowest priority)
D — Debug
I — Info (default priority)
W — Warning
E — Error
F — Fatal
S — Silent (highest priority, on which nothing is ever printed)
You can replace the *:W with any other letter from above to get more info.
From PC[i.e, ADB] GET DMESG:Difficulty --> ***
Note: You will need adb access for this to work, same as logcat. Read PREPARATIONS above to find adb files required and related setup.
What this will do is get us live kernel output so we can know things like "What driver is the kernel loading {or not loading for that matter}" and similar things.
Go to Android folder.. inside that you should find 3 files.. Now open a command prompt or terminal in that path..(wherever you extracted it.. use cd command)
Then inside that path.. type
Code:
adb shell dmesg > dmesg.txt
To get last_kmsg:
Code:
adb shell cat /proc/last_kmsg > kmsg.txt
From Android Device GET DMESG:Difficulty --> **
You can also get the dmesg by using terminal emulator.
Code:
dmesg > /sdcard/dmesg.txt
To get last_kmsg:
Code:
cat /proc/last_kmsg > /sdcard/last_kmsg.txt
FOR APP DEVS / ADVANCED USERS ONLY! LOGCAT INSTRUCTIONS:
Thanks to jaison thomas for this method! NOTE: I have not tested this. sorry. But it will definitely work. I edited the quoted message to make it simple.
jaison thomas said:
log cat using eclipse, i thought it will be simple for advanced users who are into app development.
I will guide how it works
1) install samsung kies in your pc
2) turn on usb debugging in phone.
3) install android plugin for eclipse .
4) now on eclipse click on "window" --> "show view" --> "other" --> "android" --> "log cat". Then click "ok".
Thats it .logcat window will be shown in lower bottom side of eclipse.it is having a green color icon. Also there may be a chance of logcat window minimised in eclipse.do look for a green icon.
5) now conect ur phone using datacable u can see all the things happening inside the phone in log cat window in eclipse.
NOTE: if you couldnt find android under other option.. Do this:
u didnt install android plugin for eclipse do as follows to install android plugin for eclipse.
1) click on help
2)click on install new software
3) then click on add.
4)then you will get a text box with name and location. in name text box type android or any thing,
in the location copy paste this
https://dl-ssl.google.com/android/eclipse/ and press ok,
5)In the Available Software dialog, select all check boxes and click Next.
6)In the next window, you'll see a list of the tools to be downloaded. Click Next.
7)Read and accept the license agreements, then click Finish.
8)If you get a security warning saying that the authenticity or validity of the software can't be established, click OK.
9)When the installation completes, restart Eclipse.
Click to expand...
Click to collapse

CWM MD5SUM mismatch error while restoring? Solution for this:
Difficulty --> **
If you have made a nandroid backup and we never actually test whether it works/not.. So, some day when you need to restore it.. you get an error while restoring that "md5sum mismatch" restore aborted!! Then you are in a really bad situation right?? Wrong.. Do this.. and the problem should be solved..
You need to edit nandroid.md5 file stored in /sdcard/clockworkmod/backup/"backup name"/nandroid.md5
NOTE: backup name is usually date and time of your backup/ you could have renamed it to some name.
You need terminal emulator app. Download from play store (android terminal emulator)
Open terminal emulator app and input these commands..
Code:
cd sdcard/clockworkmod/backup/2012-09-30.03.18.47
NOTE: Change 2012-09-30.03.18.47 to the name of your folder
To See what file extensions need to be included. type
Code:
ls
( lowercase "L") and hit enter.
This will list everything inside your current directory (backup files of that particular backup)
To make sure there is no nandroid.md5 file existing already, enter this command:
Code:
rm nandroid.md5
Now to make a new nandroid.md5 file
Code:
md5sum *tar > nandroid.md5
Now its ready to be used in restore inside CWM..
NOTE: USE this procedure to repair nandroid md5sum mismatch error if you are getting this on a backup which has not been modified. If you have opened the backup files to modify the files inside. Its not advised to do this. So, please take note of this.
Special Thanks to cynnar for this idea. i tweaked it to our device from his post.
CLICK HERE TO GO TO FIRST POST

How to use SDCARD instead of internal storage for apps[LINK2SD]
Difficulty --> **
Welcome to LINK2SD app friends!
Easiest app to install and use to extend your internal memory.
What it does?
It creates a symbolic link file(more like shortcut in windows) for apps in internal memory which will point to the real app which will be saved in your sdcard second partition! It mounts the second partition of your SD card as /data/sdext2 and makes OS mounts it at boot time.
It can also move user apps to SD card (force move), with batch moving (multiple apps moving at once) capability.
That feature uses Android's standard SD-card installation feature and does not require a second partition. It can break some apps if they are not meant to be moved to the SD card (Such as Widgets).​Preparations:
* You need to have root permission/access[Rooted phone]
* A second partition on your SD card. You should have two partitions on SD card and both should be primary.
* The second partition is used for application files and can be ext2, ext3, ext4 or FAT32 (I prefer FAT32 and no issues i have seen, see note below to know why?).
Note:
1. The second partition will not be accessible through windows OS as it recognises only first partition on removable devices. In Linux you can access second partition too!
2. ext4 is the latest ext format but several ROMs/Kernels have issues with it while fewer have issues with ext3 and ext2. FAT works on all ROMs.
Steps to make 2nd Partition in SDCARD:
Connect phone to PC using USB Cable. Make sure your device driver is already installed otherwise install kies software which will install drivers too.. Get kies from This LINK
Now drag the notification bar from status bar in phone and select "USB Connected" messasge.
Then select "Connect USB storage" button.
Once it is connected, Make a backup of sdcard first to PC(Copy all files inside sdcard to any fodler in PC). Otherwise you will loose data in sdcard.
Now open "MiniTool Partition Wizard Home Edition" download it from This LINK
This tool is compatible with Windows 2000/XP/Vista & Windows 7. Or Use "Gparted" tool for linux users Or "iPartiton" for Mac users.
Note: this partition manager QUEUES the operations. So nothing is deleted and changed UNTIL you click "APPLY" and then confirm by clicking "OK".
Make sure you are deleting partition on SD card! (not your hard disk for example). Dont be afraid, just read everything and think twice before selecting correct drive. Do you see three gray icons on the bottom? Under each of them the capacity of each drive is listed, and SD CARD has slightly different icon. Check the sdcard capacity given in the window to select the proper one.
select "Create As": PRIMARY on the sdcard partition. Choose whatever size(leave some space which we will use for apps partition) you want for sdcard( to have your music, personal files, etc.).
Select "File System:" FAT32
select the second partition below the one you just created which will have the space left when partitioning the first partition.
Select "File System:" FAT32 (YOU can use Ext2, Ext3, Ext4 also.) But my suggestion is please use FAT32. You wont have problems as all ROMS/KERNELS support fat32 by default!
Click "apply" button on top left corner. Partitions will be created and card will be formatted.
Now put your files back to sdcard and disconnect from PC.
NOTE: You can also use CWM partition option. If you want to use CWM partition method to partition your sdcard then see here. I have never tried this method. So i cannot help you with that.​Steps to install and use link2sd[2.2.3 version]:
Let the media scanner finish the scanning process, then open link2sd app and you will see a pop up menu "Select the file system of your SD card's second partition"
Choose your partition type for "second partition" you created while partitioning, say you choose "FAT32/FAT16" then your sdcard second partition should be FAT32/FAT16 which is nothing but FAT or vFAT.
Now Press OK. After 2-10 seconds you will see another pop up menu "Restart your phone" Press "OK" (message goes like this "Mount script created, please restart your phone to mount the second partition of your SD card.")
Now do a reboot of your phone.
Link2SD successfully installed.
To make space inside internal memory-->
* Now open LINK2SD app and you will see three buttons on top bar. click on the first button from left side. you will see:* All --> It will show you all the apk/app files in your phone (130+/- apps)
* System --> It will show you all the system apps in phone (100+/- apps)(stored in system memory)
* User --> It will show you all the User apps(i.e, installed by you) in your phone (30+/- apps)(stored in internal & sdcard & second partition memory)
* Linked --> It will show you all the linked apps in your phone (it wont show any now)(stored in your sdcard second partition memory)
* On SD card --> It will show you all the user apps (10+/- apps)(stored in your sdcard first partition. usual sdcard method)
* On internal --> It will show you all the user apps (10+/- apps)(stored in your sdcard first partition. usual sdcard method)
* Frozen --> It will show you all the apps that have been stopped. This is a method same as Titanium backup app "freeze" method. It makes your app invisible to phone. I.e, it will be installed and ready to use.. but you wont see it anywhere in launcher and if you click on a shortcut of such "frozen" app it will say "app not installed" or such message.​* Now select options button in phone, then select "Multi-Select". Now press "select all" option.
* Now press "Actions" button. In new pop up window select "Create link"
* Now in new page which appears, select all 3 options to link application, dalvik-cache, library files. Then press "ok" button and wait till the process ends. It will take time depending upon how many apps you have. around say 5 minutes.
* Now go to linked option from top bar first button from left side. and see al the apps having linked->sdacrd tag on them which means they are now in sdcard second partition..
*Long press on any app to view more options.
NOTE: 1. you cannot move link2sd app from internal memory. It is better to keep it there.
2. System applications should not be linked to SD card. Link2SD does not allow these applications to be linked.
3. Link2SD does not move application's private data directory; it moves apk, dex (dalvik-cache) and lib files.
4. Do not move keyboard apps to system memory. they wont work.
Advantages:
1. When you connect your phone to PC as mass storage, Android unmounts FAT partition but the second partition remains mounted in phone. Therefore linked applications are not affected and can be run without problems even when you have access through pc to sdcard.
2. You can use this app to uninstall system apps, move user apps to system apps or system apps to user apps.
3. You can integrate new updates of system apps which will be stored in internal memory to system apps. But please note: You should free the app first and then move them to/from system always for safety of apps so that they wont give FC. If some apps did gave FC after moving please restart the phone.
4. You can use clear cache, dalvik-cache, 2nd partition options. They wont harm your apps, they will remove only unwanted files.
Troubleshooting / Error occurance chances:
Question : When I click on "Move to SD card", I see a progress bar for 2-3 seconds and then:
pkg:/data/app/com.mobisystems.editor.office_registrered-1.apk Failure
[INSTALL_FAILED_INSUFFICIENT_STORAGE]
Answer : Your problem is a simple one.. your internal memory is low..
What link2sd actually does is.. first it moves the files to internal memory and then it sends to 2nd partition.. so you are having issues because.. say the apk file is 20 MB.. and your internal memory is around 20/less MB free.. So, it will give that error even if the second partition is totally empty..
For a work around to this.. you can make backup from titanium or just backup with any app.. then uninstall some apps.. then move that big app.. then reinstall these..
Hope your doubts are solved.. Enjoy the awesome app!
Apps Original thread link and the credit goes to RD bakpinar. So do thank him for this awesome app. You can also donate the dev by visiting his original thread.
CLICK HERE TO GO TO FIRST POST

Detailed steps to install Stock rom/Firmware through ODIN
Difficulty --> **
NOTE: Please dont install/flash FIRMWARE of OTHER DEVICES for your phones! through odin! Make double check before downloading whether its the right firmware for your phone!
Visit the threads respective to your devices to see the latest available firmware.. Links given below.
Samsung Galaxy Y --> [Stock][ROM][Odin] FIRMWARE THREAD BY DOKY73
Samsung Galaxy Y DUOS--> [Stock][ROM][Odin] FIRMWARE THREAD BY MANORANJAN2050
Samsung Galaxy Y PRO --> [Stock][ROM][Odin] FIRMWARE THREAD BY GianniDPC
Samsung Galaxy Y PRO DUOS --> [Stock][ROM][Odin] FIRMWARE THREAD BY MANORANJAN2050
To check the current version your mobile has.. Type this code in Dialer Tab which is where you type phone numbers to call..
Code:
*#*#1234#*#*
and check EX. PHONE: S6102DDLG1. See whether it is the latest by visiting samfirmware.com site and type your mobile no. for ex. 5360 in search box in right side of that site page and see whether any new update has come.
PREPARATION:
Switch on PC to windows OS and Login to your account. Make sure your device driver is already installed and your device got detected.. otherwise install kies software which will install drivers too.. Get kies from This LINK
Now connect your device to PC using USB Cable..
Open ODIN software from extracting the file you downloaded from using any of these applications like IZarc/ 7ZIP/ Winzip/ Winrar..
Note:
If you did above instruction and still device not detected? Then do this..
Unplug the usb cable..
Restart both PC and phone..
Then let the PC log in.. and give 5 mins time to it to load everything..
Then connect usb cable to phone and pc..
Open task manager in PC using CTRL+ALT+DELETE..
end process of adb.exe if its existing and kies too... do this end process only once..
Now open odin..
Instructions to install this through Odin:1. Restart your mobile by holding three buttons... Volume up+home button+power button.. Now when you see Samsung logo release the buttons... After few seconds you will see 4 options written in red text.. Which is stock recovery (Android system recovery)... select first option there.. ("reboot system now").. It will say "Rebooting..." in green colour..
2. Now when screen gets black.. immediately press and hold volume down+home button+power button..
you will see a page saying "Warning"
A custom OS can cause critical problems in your phone and installed applications.. and it will say some more in next paragraph..
Dont worry about it.. Now press "Volume up" to continue to odin mode..
3.you will see ODIN MODE written on top of screen in red..
Now make sure you are connected to your pc through usb cable and pc is logged in and open odin file..
4. Note: In Odin you will see a yellow/blue color in one box below "ID:COM" section.. If you are not seeing yellow/blue box restart your mobile and do same process from step 2. also restart your pc if its still not showing yellow. If it is showing then good.
5. Now select "PDA" button under "Files [Download]" section.. select "PDA_S****_(your firmware version no.).tar.md5" file
Now select "PHONE" button below "PDA" button in "Files [Download]" section.. select "MODEM_S****_(your firmware version no.).tar.md5" file
Now select "CSC" button below "PHONE" button in "Files [Download]" section.. select "CSC_S****_(your firmware version no.).tar.md5" file
Note: **** --> Your device model number. 5360 --> Samsung Galaxy Y, 6102 --> Samsung Galaxy Y Duos, 5512 --> Samsung Galaxy Y Pro Duos, 5510 --> Samsung Galaxy Y Pro.
6. Now remember!! Only "Auto Reboot" "F. Reset Time" options should be selected..
PDA, PHONE, MODEM also should be selected..
7. Now you are ready to flash through odin.. Just press "Start" button.. and wait around 10 minutes until odin finishes and the "yellow" box should show green... It will usually finish within 52 seconds to be precise..
8. Now your phone will reboot. If it starts showing Samsung logo again after few minutes.. Restart your mobile by holding three buttons... Volume up+home button+power button.. Now when you see Samsung logo release the buttons... After few seconds you will see 4 options written in red text.. Which is stock recovery (Android system recovery)...and select "wipe data/factory" and select first option there.. ("reboot system now").. It will say "Rebooting..." in green colour..
9. Now enjoy your brand new stock rom.. Hope this helps you!!​NOTE: IF YOU CANT GO TO ODIN/DOWNLOAD MODE.. YOU NEED AN USB JIG to force phone to Odin mode automatically.. [REF] BORROW A USB JIG NEAR YOU..
CLICK HERE TO GO TO FIRST POST

ROM installations instructions [IN GENERAL]
Difficulty --> *
OK.. so I assume you have latest firmware.. Because its always good to have latest firmware update to avoid unnecessary problems as usually updates will have bug fixes and stability improvements.. If not, then First follow the guide I have given in this thread to install the firmware update if you are not on latest version..
OK, now that we have latest firmware update installed, lets proceed to ROM installation process!
* If you dont have these files Download and keep these files in sdcard (outside all folders / root of sdcard)..
1. Rom.zip file.. link is provided in first page of the ROM thread..
2. CWM file..
Now go to stock recovery by doing this..
Restart your mobile by holding three buttons...
Volume up+home button+power button..
Now when you see Samsung logo release the buttons..
After few seconds you will see 4 options written in red text..
Which is stock recovery (Android system recovery)...
* Select 2nd option in there.. "apply update from sdcard"
* Select "CWM.zip" file u have..
* In cwm(clockworkmod) which is with yellow text..
* Now go to backup and restore option.. make a backup first.. you need to have atleast 250-400 MB of free space in sdcard to do backup...if you dont care about your data/contacts/messages currently existing in phone then no need to make backup.
* Select "wipe data / reset" and then "wipe cache Partition"..
* select "install zip from sd"
* Select "Choose zip from sdca" first option now..
* Scroll down.. and select rom.zip file..
* Then select yes option.. and wait for few minutes for it to finish.. then come bak to previous screen using power button..
* Now select "reboot system now"
* Good, Now you have successfully installed the rom.. First boot takes time.. So wait till atleast 5-10 mins.. It will vibrate onec and then it will boot to your home screen.. This guide is in general. But usually all roms have installation guide..​NOTE: THIS IS A GENERAL METHOD.. SHOULD WORK FOR MOST OF THE ROMS.. BUT IF THERE WAS ANY PROBLEM LET ME KNOW.. I WILL EXCLUDE IT FROM THIS GUIDE.. IF YOU CANT UNDERSTAND INSTRUCTIONS IN ROM THREADS THEN ONLY TRY THIS.. I HAVE WRITTEN THIS ASSUMING YOU ARE ON STOCK KERNEL/ YOUR KERNEL DOESNT HAVE CWM INBUILT. If it has.. then ignore stock recovery instructions mentioned in above instructions.. and directly start from CWM instructions..
CLICK HERE TO GO TO FIRST POST

Kernel installations instructions [IN GENERAL]
INSTALLATION PROCEDURE FOR KERNELS THROUGH CWM METHOD:Difficulty --> *
* First Download all the files required [from the kernel thread first page of whichever one you want to install]
* Copy these files inside SDCard.. Kernel.zip (kernel), CWM.zip (ClockWorkMod Recovery tool)
Note: Don't keep these files inside any "FOLDERS".. Just copy it to SDCard root (parent) folder (Outside of all folders)..
* Switch off your mobile.
After a small vibration (switch off confirmation) PRESS and HOLD 3 BUTTONS (VOLUME UP+HOME BUTTON+POWER BUTTON)
when samsung galaxy logo appears, release the 3 pressed keys..
* After few seconds.. You will see Android system recovery (red text with 4 options lines)..
Select "apply update from sdcard"
Note: (Volume up+down for "scrolling" through options or selection of files, home button for "select" any option.. in CWM only: power button for "back" option)
Then Select "CWM.zip".
* ClockworkMod Recovery v5.0.2.6 is loaded now.
Select "install zip from sdcard"
Select "choose zip from sdcard"
Scroll and Select "Kernel.zip" and select "Yes"
Wait till the menu appears again.. Now Go back
* Select "Reboot system now" and you have successfully installed Kernel.​INSTALLATION PROCEDURE FOR KERNELS THROUGH ODIN METHOD:Difficulty --> **
* First Download all the files required [from the kernel thread first page of whichever one you want to install]
* Restart your mobile by holding three buttons... Volume up+home button+power button.. Now when you see Samsung logo release the buttons... After few seconds you will see 4 options written in red text.. Which is stock recovery (Android system recovery)... select first option there.. ("reboot system now").. It will say "Rebooting..." in green colour..
* Now when screen gets black.. immediately press and hold volume down+home button+power button..
you will see a page saying "Warning"
A custom OS can cause critical problems in your phone and installed applications.. and it will say some more in next paragraph..
Dont worry about it.. Now press "Volume up" to continue to odin mode..
* you will see ODIN MODE written on top of screen in red..
Now make sure you are connected to your pc through usb cable and pc is logged in and open odin file..
*NOTE: In Odin you will see a yellow/blue color in one box below "ID:COM" section.. If you are not seeing yellow/blue restart your mobile and do same process from step 2. also restart your pc if its still not showing yellow. If it is showing then good.
* Now select "PDA" button under "Files [Download]" section.. A new window to browse files will get opened.. Locate the file boot.tar/boot.tar.md5 file you want to install.. select "boot.tar.md5"/"boot.tar" file..
* Now remember!! Only "PDA" "Auto Reboot" "F. Reset Time" options should be selected..
* Now you are ready to flash through odin.. Just press "Start" button.. and wait around 1 minute until odin finishes and the "yellow" box should show green... It will usually finish within 15 seconds to be precise..
* Now enjoy your brand new stock kernel.. Hope this helps you!!​INSTALLATION PROCEDURE FOR KERNELS THROUGH KERNEL FLASHER TOOL[MAI77 METHOD] IN CWM:Difficulty --> *
* First Download all the files required ["boot.img" from the kernel thread first page of whichever one you want to install] and kernel flasher tool
* Copy these files inside SDCard.. boot.img (kernel), KernelUpdate.zip (Kernel Installer tool), CWM.zip (CLOCKWORKMOD)
Note: Don't keep these files inside any "FOLDERS".. Just copy it to SDCard root (parent) folder (Outside of all folders)..
* Switch off your mobile.
After a small vibration (switch off confirmation) PRESS and HOLD 3 BUTTONS (VOLUME UP+HOME BUTTON+POWER BUTTON)
when samsung galaxy logo appears, release the 3 pressed keys..
* After few seconds.. You will see Android system recovery (red text with 4 options lines)..
Select "apply update from sdcard"
Note: (Volume up+down for "scrolling" through options or selection of files, home button for "select" any option.. in CWM only: power button for "back" option)
Then Select "CWM.zip".
* ClockworkMod Recovery v5.0.2.6 is loaded now.
Select "install zip from sdcard"
Select "choose zip from sdcard"
Scroll and Select "KernelUpdate.zip" and select "Yes"
Wait till the menu appears again.. Now Go back
* Select "Reboot system now" and you have successfully installed Kernel.​NOTE: THIS IS A GENERAL METHOD.. SHOULD WORK FOR MOST OF THE KERNELS.. BUT IF THERE WAS ANY PROBLEM LET ME KNOW.. I WILL EXCLUDE IT FROM THIS GUIDE.. IF YOU CANT UNDERSTAND INSTRUCTIONS IN KERNEL THREADS THEN ONLY TRY THIS.. YOU CAN CHOOSE TO USE ANY OF 3 INSTRUCTIONS TO INSTALL.. I HAVE WRITTEN THIS ASSUMING YOU ARE ON STOCK KERNEL/ YOUR KERNEL DOESNT HAVE CWM INBUILT. If it has.. then ignore stock recovery instructions mentioned in above instructions.. and directly start from CWM instructions..
CLICK HERE TO GO TO FIRST POST

How to deodex a stock rom in easy way using DSIXDA Kitchen
SPECIAL Thanks to dsixda Recognized Developer / Retired Senior Moderator who has made an all in one ROM kitchen. So thanks to him there are many custom roms are there in xda.
Difficulty --> **** IF YOU ARE NEW TO PC & ANDROID. This is not for you. If you are good with either one then you can try this.
PREPARATIONS:I Recommend you to use linux if you have it.
Kitchen by Dsixda [KITCHEN] Android Kitchen, v0.214 [Linux / Mac / Windows]
You need to have java installed in system to use the kitchen. All the steps for how to setup in windows/linux/mac has been explained well by dsixda in thread link. So i am not going to explain it here again. I assume your kitchen is set up and you are ready to work.
Make a backup in cwm and transfer the system.rfs.tar or system.ext4.tar file and boot.img file inside /sdcard/clockworkmod/backup/"dateofbackup"/ into PC.
Now go to the "/dsixda-Android-Kitchen/" folder and you should see these in that folder:
3 files & 3 folders it should contain:
- menu(file)
- Readme(file)
- .gitignore(file)
- original_update(folder)
- tools(folder)
- scripts(folder)
For Windows users--> Now open command prompt (If you installed Cygwin, then click on the Cygwin shortcut on your desktop to start it) and make sure you get to the path of that folder.. Ex. if folder is in c:\cygwin\home\"username"\dsixda-Android-Kitchen.. Then type this in command prompt..
Code:
cd dsixda-Android-Kitchen
Note: the capital letters should be in capital only when you type it... Note: Dont use space in folder names as cygwin wont work properly with space in folder names.
Or For Linux Users--> Now open terminal(Use CTRL+ALT+T). and make sure you get to the path of that folder.. Ex. if folder is in /home/"username"/Desktop/dsixda-Android-Kitchen.. Then you will be at /home/"username"/ . So type this in terminal.
Code:
cd Desktop/dsixda-Android-Kitchen
Note: the capital letters should be in capital only when you type it.
Now find that system.rfs.tar or system.ext4.tar file and boot.img file and paste it inside original_update folder. You will also find a file "put_rom_here_" Please ignore that file. Its just to tell you he has created that file.
Ok.. Now that you are at the right path.. just type ./menu in terminal or command prompt. From now on i am just going to say type this. It means you should type that and press "enter" to execute the command. If a menu didnt appear then type
Code:
pwd
You should see in which directory you are currently in. Try to get to the folder where kitchen folder is. Or follow steps again to get to there.
Now then, you should see this menu:
Code:
============================================================
Android Kitchen 0.214 - by dsixda (xda-developers.com)
============================================================
> MAIN MENU
1 - Set up working folder from ROM
2 - Add root permissions
3 - Add BusyBox
4 - Disable boot screen sounds
5 - Zipalign all *.apk files to optimize RAM usage
6 - Change wipe status of ROM
7 - Change name of ROM
8 - Show working folder information
0 - ADVANCED OPTIONS
00 - LEGACY OPTIONS (old and rarely used)
99 - Build ROM from working folder
u - Kitchen Info/Update/Donate
x - Exit
Enter option:
Enter option: 1
Press "Enter"
[CODE}Available ROMs:
(1) system.rfs.tar
Enter selection number (default=1, cancel=0, r=refresh):1[/CODE]
It will ask you this:
Code:
The new working folder will be named WORKING_111212_132324
Change the name (y/n)? (default: n):y
Give a name if you want to identify it easily next time.. for ex. i gave this "Enter a new name (using this prefix): WORKING_DDLJ1" as it is from DDLJ1 firmware update.. you can choose not to give name.
Now it will ask this:
Code:
Would you like to view this ROM's info (y/n)? (default: y):y
Give y as yes as i gave.
It would appear like this if it is stock roms backup:
Code:
Working folder information
Android OS version : 2.3.6
Device : GT-S6102
Model : GT-S6102
ROM Name : GINGERBREAD.DDLJ1
CSC version : S6102ODDLJ1
Rooted (Superuser app + su) : NO
Rooted (unsecured boot.img) : UNKNOWN
BusyBox installed : NO
BusyBox run-parts support : UNKNOWN
Apps2SD (Apps to EXT) enabled : NO
/data/app enabled : NO
Custom boot animation allowed : NO
Nano text editor installed : NO
Bash shell support : NO
/system/framework is deodexed : NO
/system/app is deodexed : NO
radio.img found : NO
ROM will wipe all data : NO
Press Enter to continue
Now press "Enter" to continue.
Setting up working directory complete.. You can close it anytime if you want when you are at main screen just type x and press "Enter". You can open it again and continue without making the above steps again..
Enter option:0 in main menu for "Advanced options"
Enter option:11
It will show like this:
Code:
NOTE: Reversing the de-odexing process by getting back the odex
files ('re-odexing') is not supported in the kitchen and would
be impossible to implement.
----------------------------------------------------------------
Found 23 *.odex files in system/framework
Found 110 *.odex files in system/app
Enter a choice:
bb = Back up both folders (do first!)
v = Set Android OS version (Current API level = 10)
IMPORTANT: Ensure you set the correct API level
f = Deodex /system/framework
a = Deodex /system/app
b = Deodex both folders (recommended)
s = Deodex a single file
x = Exit
?
Now type bb and press enter. (For safety, backup apks.. you can skip it if you want) Press "Enter" to continue.
Now type v and
Code:
Change the current API level (y/n)? (default: n):y
Please enter the new level number (currently: 15): 10
Press "Enter to continue.
Now type b to deodex your rom. Press "Enter" when this is asked,
Code:
Enable logging to file (y/n)? (default: y):
It will take some time depending upon your computer configuration. So take a small nap It takes 20 minutes in mine usually.
At the end if its successful.. you should see this:
Code:
Finished system/app
A summary of the deodexing has been logged in deodex_111212_133710.log
0 *.odex files remain in system/app
0 *.odex files remain in system/framework
Press Enter to continue
Now press "Enter" to get back to "Advanced options"
Now to make this as cwm flashable zip.. Then type 99 and press "Enter"
[CODE}Select a build option:
Number (default: 1):1
Would you like to optimize the APK files by zipaligning them (y/n)? (default: y):y
Use updater-script in ROM's ZIP file (y/n)? (default: y):y [/CODE]
Now it will show this:
Code:
An updater-script has been created under META-INF/com/google/android of
your working folder. Please review it and make any necessary changes. An
update-binary has also been added.
DO NOT delete any of the files under META-INF/com/google/android.
Proceed with the change (y/n)?
y = Proceed; updater-script and update-binary will be used in the ZIP
file; update-script will remain in working folder.
n = Cancel; updater-script and update-binary will be deleted and not
used.
? (default: y):
Now go to that "META-INF/com/google/android." folder.. And replace the "updater-script" with the file i have given in the attachment to this post. rename the "updater-script.txt" file i have given to "updater-script" and delete "update-script" file. Now after replacing the file type y in menu.
It will ask this:
Code:
It is recommended that you sign your ROM.
Sign it (y/n)? (default: y): y
The new ROM will be named GT-S6102_signed_111212_141640.zip
Change the name (y/n)? (default: n):y
and type new file name whatever you want and press enter
You will find the zip file inside OUTPUT_ZIP/"given name".zip
Now its ready to flash the zip file in CWM.
I will write about other options if any users/readers ask me to write it.. otherwise i may update it when i feel there is a need for that.
CLICK HERE TO GO TO FIRST POST

Miscellaneous section
THREAD TITLES CONFUSING? ITS EXPLAINED HERE!Difficulty --> *
[TAGS] --. Use these below tags on your title, So that people can identify it more easily and what the thread is for! Add it in front of the thread for better recognition of thread purpose.
[SOLVED] - for issues that have been fixed or [Q] that have been answered THIS IS A MUST TAG FOR SOLVED THREADS! IT WILL SAVE LOTS OF TIME FOR EVERYONE! PLEASE DO THIS WITHOUT FAIL ALWAYS!
[Q] or [QUESTION] - All Questions thread should have this.
[REQ] - Requests topics for ROM ports, INFO, THEME, MOD, etc.
[TUTORIAL] or [GUIDE] or [HOWTO] - How to do or Guides for some task or info for users/devs.
[UITIL] or [UTILITY] or [TOOL] -- Any kit or tool made for some specific task.
[APP/ 2.2+] -- Apps thread which contains apps made / ported / modded. 2.2+ such tag is also a must which tells what android os or above versions are supported.
[ROM] / [KERNEL] -- As name suggests its a rom development or kernel development thread.
[DEV] -- Developers related thread
[MOD} -- Modded ROM/KERNEL/APP etc thread
[ROOT] or [CWM] -- Rooting thread or root related to thread. CWM related thread.
[AROMA] -- Tool used in recovery. This means the thread for any ROM ? KERNEL ? OTHER WORKS has aroma to flash it.
[TWEAK] -- Tweaks to boost system performance speed etc thread.
[WIP] -- Work In Progress thread.
Also, please do add tags to your threads. See "TAGS" button above your "Quick reply option".. Now see right end of that line to find "EDIT TAGS" button. Click on it and words there.
Code:
Thread owners and others should add relevant words there
So that the thread gets added to searches which have those words
WHY GIVE THANKS? THANKS METER EXPLAINED!Difficulty --> *
Why to Give Thanks?
Giving thanks is important. It lets people know that their work or answer is appreciated. It is a faster method of feedback than posting a reply like "Thanks for your answer!" You must have made one post to give thanks,
You get 8 thanks per day, and they renew after 24 hours or so. Each thanks is independent of the others, so if you give someone a thanks at 3, and then another at 4, those will renew at 3 and 4 the next day. If you run out of thanks, then save that page in a new tab and give thanks later when you have one available. (Or if you are an app user then you can thank them through the app "Just tap on the post and touch thanks button on pop up bar which appears") If you use them all every day you are doing it correctly.
Thanks Meter:
You will see that everyone here has a Thanks Meter above their avatar.
Here are the counts needed to get to the next bar.
1st bar - 26
2nd bar - 51
3rd bar - 101
4th bar - 201
bug here, never gets to 5 bars, probably 501 if fixed.
6th bar - 1001
7th bar - 2001
8th bar - 5001
9th bar - 8001
10th! - 10000+
Not that thanks are an indication of a user's status or stature on XDA. Thanks don't really count for anything other than as a potentially wildly inaccurate measure of a member's ability to answer your question correctly. Some of the most important people here have a lot fewer thanks than you might guess. But it is a nice gesture to hit thanks button to those who helped you as they are not gaining anything in return!
STARS, USER TITLES: JUNIOR, MEMBER, SENIOR MEMBER........? READ TO KNOW MORE!Difficulty --> *
0 to 29 posts - Junior Member
30 to 99 posts - Member
100 + posts - Senior Member
Here is what our Senior Moderator said,
juzz86 said:
There are Junior Members, Members, Senior Members first. These make up the vast majority of XDAs userbase.
Recognised Contributors are nominated by other users and/or Mods/Developers. They are recognised for their contributions which are not specifically Development, such as detailed guides, one-click utilities and other tools/mods.
Recognised Themers are also nominated by users/Mods/Developers, for their work themeing custom ROMs and providing standalone themes for flashing.
Recognised Developers are nominated and approved by the Developer Committee, for their work in Development whether it be ROMs, Root methods, bootloader unlocks etc.
Elite Recognised Developers are again assessed by the Developer Committee, and are deemed to have gone above-and-beyond in providing knowledge/hacks/tools/apps/ROMs for the XDA community.
Forum Moderators are appointed by the Moderator Committee, after submitting an application (see the 'sticky' at the top of this forum - currently applications are not open). They are the first-line of keeping the forums tidy, friendly and orderly.
Senior Moderators are the next step up the ladder, providing site-wide support for Forum Mods and looking after the nitty-gritty issues, as well as areas of XDA not policed by FSMs, such as the Marketplace.
Administrators are next. There are several Admins - each look after a specific part of XDA such as the Portal, the Members and the User Experience of XDA as a whole.
At the top is Mike Channon, who is overall Forum Administrator.
Other titles you may come across:
Moderator Committee - sits on the Mod Committee
Developer Committee - as above, but for Developer Committee
XDA Newswriter - publishes articles for the Portal (front page)
Retired xxxx - have since officially 'left' their XDA position
Hopefully that clears most of them up for you
Contrary to what a lot of people expect, the thanks-meter does not figure at all in determining a users tag.
Click to expand...
Click to collapse
Wondering what those stars below the thanks meter mean?
It means that they've donated money directly to XDA.
A star = €10 euro donation.
A star with 10 written within it = €100 euros, as it represents 10 individual stars.​
XDA/TAPATALK APP IMAGE UPLOADING PROBLEMS?? Difficulty --> *
Use Imgur Mushroom app.. its available at play store..
Its app size is very small.. Its a great app for multiple pictute uploads at once..
Whatsmore u can configure prefix and suffix text in settings to add [img] and [/img]..
After uploadingthe pics, it will save all links with prefix and suffix code in clipboard. ready made for you to paste it in the desired post using the XDA/TAPATALK app..
So all u need to do is paste it in post.. very easy and handy.. How to do it? Instructions below!
open imgur mushroom app. Select button right side to upload button which has this "..." button.
now select "settings" in the newly opened pop up menu.
now scroll down and select "output type" in URL settings section.
select "URL to direct image"
select "prefix text" and add [img]
select "suffix text" and add [/img]
now go back and select "pick" button and choose your pics to upload. Alternatively you can multi select in a file browser and share them to this app to upload too! Hope this helps!
MAKE YOUR THREAD/POST NEAT BY USING BBCODE [Bulletin Board Codes]: Difficulty --> *
You see in many Threads and posts people using something to make it look cool / formatted to make it more readable?
And you wish to make your threads/posts the same way??
Then look at this link provided by XDA.. I know many wont know about this..
BBCODE EXPLAINED WITH EX. BY XDA.. CHECK THIS LINK
I will add other info that are not informed there soon..
BATTERY DRAIN?? READ THESE TIPS TO AVOID IT! Difficulty --> *
Are you using live wallpaper? it takes more battery!
Go to Settings-->Accounts and Sync-->Auto-sync option-->uncheck it to save more battery.
If you keep using 3g/wifi it will use more battery.. Use 3g only when u download something..
If you are using widgets, it does drain battery faster.. If you want your battery to last longer, remove them or keep it to minimum 1 or 2. I dont use any widgets.
You have to pay attention to your apps running in the background. Try "Quick system info pro" or "ES Task manager" or "some other apps which shows detailed info on processes running. Stop those processes.
If you are using too many notifications features types of apps it will drain battery as they run in the background all the time..
Keep the screen brightness to as low as possible and readable still. Brightness does takes battery a lot.
Playing games does drain battery faster.
If you have custom kernel, and keep minimum freq higher then it will drain faster too
When u sleep at night and wake up at morning how much battery u lose? I loose around 1 percent.. If its more than 2-10% may be your deep sleep feature is not working.. Check it with CPU SPY app available at play store.
[DUOS ONLY]Do you keep both sims alive? I switch off 1 in sim manager.. Do it if you don't need it all time..
Inspired by a.cid and mf2112 threads.
Enable Whatsapp *AUTO DOWNLOAD IMAGE OPTION* in new versions [TRICK] (2.9.**** versions and above)Difficulty --> *
If you have lost "Auto-download images" option.. Then you are not able to disable the auto download of images. So, to get back that option in Settings-->Chat Settings. You need to do these steps below:
Note: Make sure you have a working Whatsapp already before attempting this. That is you should have already passed the verification process etc and able to chat with others.
Step 1 : Make sure you have "Ticked" option "Unknown sources" under Settings-->Application Settings.
Step 2 : Download this old version Whatsapp and transfer it to click on the downloaded file. It will ask "Replace application"
Press "OK". Then, Press "Install" button. After install press "done".
Step 3 : Now, switch on "Airplane Mode" to "ON" by lidroid toggle or in Settings-->Wireless & network settings--> Flight mode "ON"
Step 4 : Go to Settings-->Date & Time.. Change date to any date/ November/ 2012. Now, open the Whatsapp.. You should see a old Whatsapp.
Inside Whatsapp, Go to settings-->Chat settings and now turn off "Auto-download mages" option by "unchecking" the tick box.
Step 5 : Now, install the new Whatsapp if you have a backup of the app and turn off "Airplane mode" and now you can also update from play store if you dont have a backup of latest version of Whatsapp.
Now open the new Whatsapp and see the option "Auto-download image" option.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
CLICK HERE TO GO TO FIRST POST

Useful links to threads/guides section
NOTE: I am not adding any SGY forum threads here.. as we all can look into it easily.. I am adding only other forums thread links of XDA which are very useful to us. So please dont ask me to add SGY forum thread links here. And if you find any useful threads which are not similar to already mentioned thread.. Then PM me the link.. I will add it if its good. Thank you for reading!​Thread Titles with links and info about it are below:
****XDA SITE RELATED THREADS****​[All XDA Members] Requests to Moderators and Admins --> Rather than sending a PM to an individual Moderator, please see this thread in need of Moderator or Admin assistance. They will all be monitoring this thread, and someone will reply without much delay.
XDA Android App - Problems / Bugs / Feature Requests etc. --> Report any faults you find with XDA app in this thread. You can also ask for new features, but cannot promise they will ever be delivered.
SPAM Users --> Any user Spamming in forums / threads? If you feel yes, then do go to this thread and report the user. Please give direct link to the users profile/posts which were spam so that it will help moderators.
[HOW TO]Make The Most Of The XDA App --> This is for all of you who use the app instead of desktop, but may not know how to do certain things.
I Will Post Your Question In The Dev Thread If.. --> Newbies not able to post in dev thread? Some report you want to get it there? Then check this thread to do exactly that!
Help Your Threads Get More Search Hits with Better Titles and Thread Tags! --> I have noticed that many threads do not have thread tags so I think most users don't know about them. This only works with
the XDA website, not the XDA app. Please read this thread to know more about tags which is a very useful method to get your thread popular!
Time Frame/Tell your story here on xda![Archive] --> Where we could talk about our years here at XDA. Lets see who is the oldest and what we have given to this forums.
Share your sig code please --> Very helpful to make your Signature look neat. Read this thread to make your signature better or if you have cool signature then post there.​****GENERAL INFO THREADS****​[MOD][2.56] AROMA Installer :: 121004-031 :: Open Source --> The World's First ANDROID Touch And Customizable ROM/KERNEL/MODS Installer
List of devices: ARMv7, ARMv6, ARMv5 --> I found a really nice thread that will maybe, help some developers who need to port Roms or for another Reason.
[v6.13] Online Nandroid Backup / Nandroid Backup without re-booting
[HOW-TO] Set up SDK/ADB on Ubuntu 11.10 | 32 & 64 bits
[TUTORIAL]How to make your own Live Wallpaper
[Tutorial/How-To][GB] Make Your Own Custom Rom & Kernel (Last Updated 30/07/2012)​****ROM RELATED/INFO THREADS****​
ROM DEVELOPMENT THREADS:
[HOW TO] Beginners Guide to Android ROM Development
[Guide]Complete Android ROM development and essential tutorials ~~ By Nero Young ~~
[KITCHEN] Android Kitchen, v0.213 [Linux / Mac / Windows]
[Ultimate Guide][Part 10 released][12/11/2011]Android App Development - From Scratch
ROM MOD THREADS:
[UTILITY] Android Utility - [apktool|dex2jar|smali|more][Mac & Linux][Feb13, 2012]
[MOD][HOW-TO]To disable signature checks
[GUIDE] How to add TABS to Settings with swipe gesture... \m/
[GUIDE] ICS Style 'Settings.apk' - Make it yourself !! !!
[UTIL][Sept 2 2012] Apktool v1.5.0 - a tool for reverse engineering apk files
[IDE][M10] Virtuous Ten Studio - The next level of editing apps
[KITCHEN][01/22] UOT Kitchen (Ultimate Online Theme Kitchen) version 4.0
[MOD][15 Toggles] How to mod Lidroid framework
[APP][DEV] Update me [ROM MAKER] - 2.0.3 - PUSH NOTIFICATION - (updated 2012-09-13)​****KERNEL RELATED/INFO THREADS****​
KERNEL DEVELOPMENT THREADS:
[KITCHEN]Android Kernel Kitchen 0.2.3 (Linux / Windows)
[Tutorial] Building Your First Kernel
HOWTO: Compile your own kernel from source (WIP)
[Tutorial] How to compile a kernel module outside the kernel
KERNEL MOD THREADS:
[REF][TWEAKS] Kernel Governors, Modules, I/O Schedulers, CPU Tweaks, AIO App Configs
[KERNEL MODULE] Extra modules pack v0.1.3 (feat. overclock) [OMAP4 kernel 3.0.8]​****RARE/COOL APPS THREADS****​[APP] Updated: 31/10/12 - PIT Magic v1.3.10 - Samsung PIT Creator, Editor, Analyzer!
[APP][DEV] ZipInstaller 2.4.2 for CWM-based + TWRP + 4EXT Recoveries
[APP][2.1+] Gidder - Git server for Android
[APP/5 NOV/2.2+]Turn screen off while MHL/HDMI mirroring WITH TOUCHPAD! [v1.96B11]
[APP][2.1+] FTP Server Ultimate - FTP, SFTP, FTPS server with multi-user, no-root
[App] WifiKill - disable internet for network hoggers (Android 4.x) [31/10/2012]
[App]Mediafire App for Android
[App][2.2+]LauncherWP8[6nov][v1.1.1]
[APP 2.2+] Android Tuner [BETA TESTING]
[APP]DroidSheep : ARP-Spoofing App for Android​****MISCELLANEOUS THREADS****​[TWEAKS][SCRIPTS] Collection of 'em all - build.prop; init.d; etc.
☠ [Add-on][Tweaks\\Mods]█ PIMP MY ROM █ v2.1.2 {Any Device // Any Rom}[AROMA][WIP] ☠
[Tool][Windows Only][Root] Android Reverse Tethering 2.30 --> surf on your phone using the ADSL of your PC.This work only for rooted users !
[ICON PACKS] mrFenyx's Icons - 8 packs, 800+ Icons, more to come
[Rooted][Guide]Wifi Reverse Tether - Windows and Ubuntu - Ad Hoc Networks​ CLICK HERE TO GO TO FIRST POST

Well, even though there are 2 kernel guides in our section.. Both are not complete.. So i thought of writing this.. a complete guide to make a kernel.
So, i'll keep updating this post as and when i get time to make it as good as possible..
Files Required:
You need to have Ubuntu or any other Linux distros.. But i recommend Ubuntu 11.10 32 bit as I'm using this version.
Kernel source from http://opensource.samsung.com . Search for 5360 and download "GT-S5360_GB_Opensource_Update3.zip"
Download Sourcery G++ Lite 2009q3-68 toolchain for ARM EABI from http://www.codesourcery.com/
Note: It should be Linux version without installer arm-2009q3-68-arm-none-eabi-i686-pc-linux-gnu.tar.bz2. Extract this file & you need to extract the file you got again to get "arm-2009q3" folder.
Download mkbootimg_src.zip from http://d-h.st/xnT
split_bootimg.pl is a perl script required to extract ramdisk from boot.img file. Or use dsixda or championswimmer's kitchen to extract it.
Get ncurses-5.9 lib if you want to work with menuconfig..Link
stock "boot.img" to extract ramdisk for your kernel.
Now that we have all the files required. Lets move on to next step of creating a Build Environment.
Build Environment Setup:
Make a folder. I'll call it "Kernel" folder here. You can name it whatever you want. Now, move the "arm-2009q3" folder inside this "kernel" folder. Extract mkbootimg_src.zip file and move "mkbootimg_src" folder inside "kernel" folder. Move "split_bootimg.pl" file under "kernel" folder too.
CLICK HERE TO GO TO FIRST POST

nice initiative but dont repeat any tuts which we already hav.. good luck!

hell_lock said:
nice initiative but dont repeat any tuts which we already hav.. good luck!
Click to expand...
Click to collapse
lol.. i know mate.. thats y i didnt write till today even though i wanted to write.. see the index page.. almost all are my own findings.. but whenever if i added from others.. then i will add credits as always..
do tell me / crrect me if i am wrong anywhere lol

nice guide...waiting for guide on building custom rom...
Sent from my GT-S5360 using xda app-developers app

anmolsharma1293 said:
nice guide...waiting for guide on building custom rom...
Sent from my GT-S5360 using xda app-developers app
Click to expand...
Click to collapse
My sign has it already..
Sent from my GT-S5360 using XDA

Hi, maybe you would like to incorporate my tool(AIOlog) in the retrieving logcat using computer as it works for Windows out of the box(provided that the driver is installed)

wcypierre said:
Hi, maybe you would like to incorporate my tool(AIOlog) in the retrieving logcat using computer as it works for Windows out of the box(provided that the driver is installed)
Click to expand...
Click to collapse
OK.. thanks for the heads up.. I will see.. I don't know about your tool yet.. so I have to see how it works.. and I still have to write about PC log too..
Thanks for the heads up..
Sent from the MUST have app!

nitubhaskar said:
OK.. thanks for the heads up.. I will see.. I don't know about your tool yet.. so I have to see how it works.. and I still have to write about PC log too..
Thanks for the heads up..
Sent from the MUST have app!
Click to expand...
Click to collapse
Basically for now its more or less the same as the ones in the market, but if you try the latest dev version, it has multiple device support(able to do logging even if there's more than one device, usually the logging would fail if there's more than one device) and many other features that are to be implemented

:good: :highfive:

Windows imageres.dll being a PiTa: Modding

I've edited my imageres.dll file and have it all nice nice, but when I try to paste it into system 32 (tried safe mode) It will not let me overwrite that file.
I've tried Safe mode, Taking Control, Granting full control permissions of file, system32 folder, windows folder, and C folder (both taking control, and granting full permissions to: User (me) and Administrator (also me) Yes, i'm on windows 7 64bit but there is no Win 7 Forum here, however the imageres.dll is mentioned here, and I'm assuming the file is more-or-less the same. Besides taking ownership in C for Win 8 being bad? I did this to both System32 file and Syswow64 file- its now apparent to me that both are in USE and thats why I can't overwrite/modify them =/ So how do I use my modded one? (startup sound etc.)
Following this:
Code:
How to Take Ownership in Windows 7
1. Locate the file or folder on which you want to take ownership in windows explorer
2. Right click on file or folder and select “Properties” from Context Menu
3. Click on Security tab
4. Click on “Advance”
5. Now click on Owner tab in Advance Security Settings for User windows
6. Click on Edit Button and select user from given Change Owner to list if user or group is not in given list then click on other users or groups. Enter name of user/group and click ok.
7. Now select User/group and click apply and ok. (Check “Replace owner on sub containers and objects” if you have files and folder within selected folder)
8. Click ok when Windows Security Prompt is displayed
9. Now Owner name must have changed.
10. Now click Ok to exist from Properties windows
Once you have taken the ownership of file or folder next part comes is Granting Permissions to that file/folder or object.
How to Grant Permissions in Windows 7
1. Locate the file or folder on which you want to take ownership in windows explorer
2. Right click on file or folder and select “Properties” from Context Menu
3. Click on Edit button in Properties windows Click ok to confirm UAC elevation request.
4. Select user/group from permission windows or click add to add other user or group.
5. Now under Permission section check the rights which you want to grant i.e check “Full Control” under the “Allow” column to assign full access rights control permissions to Administrators group.
6. Click Ok for changes to take effect and click ok final ok to exit from Properties window.
Now you can access files of folder in windows 7 with full permissions and take full control.
also tried cmd prompt
Code:
takeown /F "C:\Windows\System32\imageres.dll"
with Sucess message (probably the same as my right click takeown reg file context thing)
I'm the only person/login/user on my PC. Ugh this is a pain in the butt. No matter what I've googled/tried hasn't worked. I don't have a linux CD/USB boot *(dunno if I do? but don't think I do) to repair/replace file, I may have Win 7 repair on my CD, maybe not.
EDIT: replacing the startup sound in imageres.dll in System32 and SysWOW64 folders still leaves me with default windows startup sound =( Only other file was imageres.dll in winsxs folder- copied, edited the copy, deleted the original with Fileassassin (it was locked, wouldn't edit, blah blah) STILL uses old windows start up sound, WHyyyyyy? theres MUI files with info for imageres.dll but IDK what's left where this sound exists =/ or where its coming from.

there used to be this program made for replacing system files
i don't remember its name, though
http://www.askvg.com/right-click-re...utility-to-replace-system-files-in-windows-7/

No manual methods worked for me, but just came across this and it worked, WOOT!
http://winaero.com/download.php?view.10

Starting with Windows 8, the administrator is no longer the same as root. Microsoft has very, VERY severely limited the administrator's abilities with many aspects of the system. This was done in an ill-conceived notion that they could curb piracy of Windows Store apps (like there's anything worth stealing in there, including games). People have already found a way to pirate Windows Store apps, so it was all just a way to irritate admins and hobbyists in the end.

@dragon_76: Care to explain what you mean by that? For one thing, Administrator on NT has never been "the same" as root (on POSIX); there's always been the local SYSTEM SID (which does some of the things which root would handle, such as being the process that drivers and initial user-space processes run as) and while I'm not entirely sure when the TrustedInstaller SID was added (may have been there since NT3.1 for all I know), it's been a part of Windows since well before Win8. For another thing, unlike root on a POSIX system, Administrator does not (and never has) automatically have access to everything; it's a SID like any other, and ACLs can be put in place to control its access.
Now, two powers that Administrator (and members of the Administrators group) do have are as follows:
1) Take ownership of any securable object (this allows completely overwriting the ACLs).
2) Impersonate any other SID (although some, like TrustedInstaller, are possibly trickier to impersonate in Win8 than they used to be; I need to investigate that).
If what you're complaining about is the fact that \Program Files\WindowsApps\ is now owned by TrustedInstaller and harder to mess with than you'd like, um... sorry? It's not *that* hard to take ownership (or set it back) from TrustedInstaller; you can do it as Admin, in fact.

*Ahem*
Back to *actually* being on-topic, older versions of Windows* had a background service that would undo any modifications to system files by replacing them with un-tampered copies from a backup location. Starting with Vista, such a service supposedly no longer exists, but it would be easy to implement something like it using VSS. So, you should verify that the file isn't being reverted. The simplest check is the modify timestamp and (if it's different on your file than on the stock one) the size. Somewhat more advanced is to use a hash function, such as MD5 or something from the SHA family, on the on-disc file and see whether it matches the version you put there.
Beyond that, you can easily replace system files if you do it while the OS isn't booted. Linux can do it, although that has risks. Better is to use WinPE (the Pre-installation Environment that bootable Windows disks and recovery tools load) and replace it from there.
Incidentally, you can use the command line tool icacls (which may even be present in WinPE by default) to both change ownership and set permissions on files and folders.
* Pre-Vista, which was the first version to switch to using TrustedInstaller to protect system files rather than letting Admin write to them by default. That's the last major change I'm aware of in the powers of the Administrator account on Windows, incidentally...

[GUIDE] Full FileSystem Access over SFTP / CMD over SSH on Windows 10 Mobile

Hi all,
This guide uses the built-in SSH server on the phone that gets activated once you enable Device Discovery to give us TRUE full file system access. MTP doesn't truly give full file system access as there are files and folders that aren't accessible still.
NOTE: The automation of the steps listed in this whole guide has been incorporated into an easy GUI within @gus33000 's app called Interop Tools. Big thanks to him for taking the time to simplify this whole process.
Many thanks to @gus33000 [For the simplification and guinea pig process ] and @black_blob [ For making me try the UMCIAuditMode trick again]!
Manual Steps for SFTP
Tools needed
@djamol's Root Tool , or even the OEMSetting.reg tweak that @WojtasXda came up with
Some SFTP program (Swish Easy SFTP works the BEST, WinSCP works second best, but for some reason it can't read the root C: drive from SFTP).
Steps:
If you're using @djamol's Root Tool, use @vcfan's Lumia Registry Editor for this
The following keys should be set to the following string values under the Path of System\Currentcontrolset\control\ssh\sirepuser
Represented in this guide as key: value
stfp-home-dir : C:\
default-home-dir : C:\
sftp-mkdir-rex : .*
sftp-open-dir-rex : .*
sftp-read-file-rex : .*
sftp-remove-file-rex : .*
sftp-rmdir-rex : .*
sftp-stat-rex : .*
sftp-write-file-rex : .*
auth-method : password
user-pin : 1234
After you've verified that at least one of these keys have been set, exit the app
[*] Go to the phone settings app and put your Windows 10 Mobile phone in Developer Mode, activate Device Discovery then turn on Pair mode
[*] Pair to your phone using WConnect, either from usb connect mode ("wconnect usb") or IP (wconnect youripaddress) using the pin on your device
[*] When this is complete, go to %USERPROFILE%\appdata\local\Microsoft\WConnectSrv. In this directory, you should see a privkey.pem file. Hold on to this
[*] Open up PuttyGen, click on the Conversions menu and then click Import key. Point to the path that contains the privkey.pem file, then press Okay
[*] Back in PuttyGen, click on the Save private key button and then save the .ppk file off somewhere that you'll remember.
[*] Open Pagent, click Add key and point to the .ppk file you generated before. You'll want to make sure this is ALWAYS running.
If using Swish
Go to Windows Explorer, dbl-click on the Swish icon under Devices and Drives. Click on Add SFTP Connection at the top
Enter in a label that you wish to save the connection present as .
Under host your phone's IP as Host.
Enter in Sirepuser as the User.
Enter / as the Path.
Press Create
Go back to the Swish folder then click on the connection that you just created (YOU MUST HAVE PAGENT RUNNING FOR THIS TO WORK).
When prompted, enter "1234" as the password.
If using WinSCP:
Open WinSCP. Underneath of the Password box, click on Advanced.
Click on the SFTP menu item and set the Preferred SFTP protocol version to 2
Click on the SSH -> Authentication menu item. Click Allow agent forwarding, click on the ellipsis next to Private key file and choose the .ppk file you saved from PuttyGen
Press Ok to save the settings
Back on the WinSCP main screen, enter in your phone's Wi-Fi IP into host name and for the User name, type in Sirepuser. Press save and then save this session as a "Site" in WinSCP
Login. When prompted, enter "1234" as the password.
You'll receive an error initially about not being able to browse /C/ and blah blah. You can right-click and click on Goto Folder. /C/Data will be a nice folder to start at since that's where most of the goodies are.
Voila, you should know be able to have full file system access.
Now there are a FEW caveats to this..
If you're looking to modify/download any of the important files in the AOW folder, you won't be able to. For SOME REASON, it's returning "No such file or directory" if you try to download/modify some certain files. It will also return this if you try to do the same for the registry hives.
If you happen to remove all paired pins on your phone, you must add pin from the phone and use the pin as the password to your SFTP session
I'm tired of my SFTP access cutting out because the WiFi disappears when the screen goes to lock >_<. What do I do?!?!!?
Using the same Lumia Registry Editor from Djamol's Root Tool, Head to the \system\currentcontrolset\services\keepwifionsvc Path and set the following DWORD value
Start => 2
For some reason the service that keeps wifi running even while the screen is under lock is disabled on 10512. This enables it. Reboot and you'll have WiFi working under lock screen on 10512.
Manual Steps for running CMD over SSH (assuming you've done the SFTP steps above) Redstone builds required. 10586.XXX builds will NOT work
Tools Needed:
IoT Insider Preview ISO
Interop Tools - Download the latest arm package and all packages from the Dependencies directory. Install the dependencies first, THEN install the app.
Pageant
Putty
Steps:
First, you'll need to download the Windows IoT Core Insider Preview ISO. Mount it and then install the MSI. Next, you'll need to go into Disk Management (diskmgmt.msc) and create a new 4GB VHD by clicking Action-> Create VHD. Set the location to any place you wish for it to be, set the size to 4GB and keep the rest the same. Pay attention to the disk number shown in the Disk Management screen after you create and mount that VHD (They have a blue drive icon to the left of them).
When this is complete, open up an elevated command prompt. Go to C:\Program Files (x86\Microsoft IoT\FFU.
Run the following command:
Code:
dism.exe /Apply-Image /ImageFile:flash.ffu /ApplyDrive:\\.\PhysicalDriveN /SkipPlatformCheck
Where N is the disk number. At this point, you should start seeing a bunch of volumes created. The MainOS volume is the one we'll care about.
Go to that drive and copy the Windows\System32\cmd.exe and Windows\system32\en-us\cmd.exe.mui to your phone's Document's folder.
Next step is to open up the Interop Tools app, and tap on the Interop Unlock menu item from the hamburger menu. Select the option to restore NDTKSvc, reboot.
When the device comes back up, re-open Interop Tools and this time click on the Registry Editor from the hamburger menu.
Enter the following values, then press Write Data:
Registry Hive : HKEY_LOCAL_MACHINE
Registry Type: String
Registry Key Path: SYSTEM\Controlset001\Control\SSH\Sirepuser
Registry Value Name: default-shell
Registry Value Data: C:\Data\Users\Public\Documents\cmd.exe
Write this key tap on the hamburger menu and go to the Registry Browser. Travel to HKEY_LOCAL_MACHINE -> SYSTEM -> ControlSet001 -> Control -> Ci.
Tap the + button on the application bar and make sure the values are set to the following and then press Write:
Registry Hive: HKEY_LOCAL_MACHINE
Registry Type: Integer
Registry Key Path: SYSTEM\ControlSet001\Control\CI
Registry Value Name: UMCIAuditMode
Registry Value Data: 1
This actually enables the execution of unsigned executables. This is how we end up making CMD and the other programs work ^_^.
Reboot your phone. Wait a good 3-5 minutes before you try doing anything because your phone will be acting very unstable (Some apps crashing, and others working).
While you have pageant open and the private key added, open up a putty SSH session to your phone using the username of Sirepuser. You should be delighted at this point (If you did everything correctly) to see a Command Prompt. You should be getting random resource string errors when you try typing DIR, etc and this is due to the fact that we don't have the mui string in the correct place. Let's fix that.
ONE BIG THING TO NOTE: running CMD in SSH is very sensitive to keystrokes. If you are typing a command and press backspace even once, then the command won't send at all. It will state that it doesn't recognize what you're doing, so be sure to type these things in FLAWLESSLY (yeah it's annoying)
What we want to do now is then copy the cmd.exe to C:\Windows\System32 and the cmd.exe.mui to C:\Windows\System32\en-US. Run the following commands:
copy c:\Data\Users\Public\cmd.exe c:\Windows\System32
copy c:\Data\Users\Public\cmd.exe.mui c:\Windows\System32\en-US
Back on your phone, go back to Interop Tools and click on the Registry Editor. Follow the same exact steps as you did for changing the default-shell key, but make one change:
Registry Value Data: C:\Windows\system32\cmd.exe
At this point, restart your putty session and then you'll be good to go with CMD running over SSH as SYSTEM!
Extra:
There was a reason I said to copy off the system32 folder somewhere... If you follow the same process to get the files to your Documents folder and move them over to system32, you can have quite a bit of exes to run from the command line. The easiest thing to do is to use xcopy to get everything there.
Extra #2:
You can run .NET Console apps in CMD if they are named the following 3 names: TailoredDeploy.exe, WConnectAgent.exe or WConnectAgentLauncher.exe.
Make a directory on your SD Card named "test" or put it in the test directory on your phone's C: drive and it should go. Beware that the runtime is weird on the phone and not ALL things are possible to do with a .NET Console app
PLEASE... For the love of god DO NOT add DefApps to the Administrators group if you don't want all of your apps to stop working
Have fun ^_^
Also...
USE THIS AT YOUR OWN RISK! I AM NOT RESPONSIBLE IF YOU BLOW UP YOUR PHONE ON PURPOSE OR BY ACCIDENT

Hi, snickler! Can I have your permission to repost your tut? It's great and I wanna share with everyone since everyone's really hoping for a full fs access. Of course, i will link your post and add you and the others to the disclaimer.

OH My god . very good so fast . forget MTP Full FS for ever

ngame said:
OH My god . very good so fast . forget MTP Full FS for ever
Click to expand...
Click to collapse
"Theoretical Full FS"

I've tried, but failed
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

@zetvn, did you follow ALL steps? Make sure Device Discovery is on and that your phone's WiFi is on. That message basically means you have a timeout. Also check your IP address and see if it is the correct WiFi address

ADeltaX said:
"Theoretical Full FS"
Click to expand...
Click to collapse
It's full access until you want to modify any of the IMPORTANT files in the AOW directory lol. I'll see how I can get around that and post more, but yes this IS indeed full access.

snickler said:
It's full access until you want to modify any of the IMPORTANT files in the AOW directory lol. I'll see how I can get around that and post more, but yes this IS indeed full access.
Click to expand...
Click to collapse
I was replying about MTP, not about SSH access. lol

. Have you gotten any closer to rooting AOW @ADeltaX?

Is there any way to copy files to C:\Windows\Fonts in the phone without the PC?

snickler said:
. Have you gotten any closer to rooting AOW @ADeltaX?
Click to expand...
Click to collapse
70% yes.
Adb shell is now as root user.
SU binary works fine.
Busybox too.
Superuser app seems to work too.
BUT
Apps can't reference from superuser app because of limit of project astoria caused by some modified libs. (stderr stdout = null)
SU binary refernce from libc.so and it's also modified....

ADeltaX said:
70% yes.
Adb shell is now as root user.
SU binary works fine.
Busybox too.
Superuser app seems to work too.
BUT
Apps can't reference from superuser app because of limit of project astoria caused by some modified libs. (stderr stdout = null)
SU binary refernce from libc.so and it's also modified....
Click to expand...
Click to collapse
Brilliant! Is it on your thread yet? If so, point me to it

snickler said:
Brilliant! Is it on your thread yet? If so, point me to it
Click to expand...
Click to collapse
Not yet, I need to upload these files and create a new thread.
I have a very slow connection, so probably will be ready within 2-4 hours :\
I'll mention you if i'll open the thread/the file is ready.

ADeltaX said:
Not yet, I need to upload these files and create a new thread.
I have a very slow connection, so probably will be ready within 2-4 hours :\
I'll mention you if i'll open the thread/the file is ready.
Click to expand...
Click to collapse
Awesome! Yeah, definitely make a new thread for this. BTW, I updated my OP to include a reg key change to enable WiFi under lock screen. It may not be useful for everyone connecting via USB, but for those on IP it will be VERY helpful

guys please answer: Is there a way to copy files to fonts folder from the phone without using PC?

MrMHK said:
guys please answer: Is there a way to copy files to fonts folder from the phone without using PC?
Click to expand...
Click to collapse
Look at Djamol's Root Tool. There's utilities in there that you should be able to move files with.

Time to play... Thanks for this!

Invite me too
ADeltaX said:
Not yet, I need to upload these files and create a new thread.
I have a very slow connection, so probably will be ready within 2-4 hours :\
I'll mention you if i'll open the thread/the file is ready.
Click to expand...
Click to collapse
Invite me too plz, I want to learn much & much again...

Lost...
Hey there i am following the instructions as written, went to install the vcREG bootstrap and the instructions they give is to apply it to the reinstalled Extras+Info app on the SD card. well when i try to download it it says the app is no longer available? is there a work around?

AteBitDesigns said:
Hey there i am following the instructions as written, went to install the vcREG bootstrap and the instructions they give is to apply it to the reinstalled Extras+Info app on the SD card. well when i try to download it it says the app is no longer available? is there a work around?
Click to expand...
Click to collapse
You didn't follow instructions. It states to use Djamol's root tool and use the Lumia Registry Editor within it that is vcReg's.