If you try this method, I nor anybody else is responsible for any further damage done to your phone.
Models Confirmed : V300L
We currently have firehose for V30.
Therefore, we can program UFS flash memory in 9008 mode.
It requires rawprogram?.xml(s) and patch?.xml(s) to program it.
It's easy to generate rawprogram?.xml(s) from kdz file, but generate patch?.xml(s) is not easy. (Unfortunately, I couldn't have time to generate patch?.xml(s)).
I have edited kdztools to generate rawprogram?.xml(s) easily (You can generate it by using "-r" argument. Currently, generate patch?.xml(s) is not supported. I'll add it soon).
I used patch?.xml(s) in post. it works well, but boot loop in the LG Logo.
However, it was possible to enter download mode.
------------------- GUIDE -------------------1. Download rawprogram?.xml patch?.xml with images from link. (It uses V300L30h000906.kdz)
2. Download firehose (prog_ufs_firehose_8998_lgev30.elf) from link.
<< Linux >>
3. Build qdl or download pre-built binary
4. Extract zip or tar.gz files 1, 2, 3 in any folder.
5. Run
Code:
$ ./qdl --storage ufs prog_ufs_firehose_8998_lgev30.elf rawprogram0.xml patch0.xml rawprogram1.xml patch1.xml rawprogram2.xml patch2.xml rawprogram3.xml patch3.xml rawprogram4.xml patch4.xml rawprogram5.xml patch5.xml rawprogram6.xml patch6.xml
in the terminal.
6. If LG logo shows, enter to the download mode.
<< Windows >>
3-6. You can program by QFIL similar as qdl.
7. Connect to any Windows PC with LGUP (must support Android Pie).
8. Flash kdz with ChipErase. (IMPORTANT)
9. If it boots successfully, your device has unbricked.
you can create rawprogramer and patch.xml with this program
I have already tried it on lg v10 kdz with successful.
after extract kdz :
1-open qualcomtool 2.4 and go to EMMC tabe.
2-clic browse and select primarygpt_0.bin
3- select all partitions and click exract partition
4- click extract firmware
you will find every things you need in extracted folder.
you can edid rowprogramer.xml with notepad ++ .
edit : tryed with lg v30 kdz not work
(gpt not present when select file)
Thank you for your work
download problem
quickwshell said:
If you try this method, I nor anybody else is responsible for any further damage done to your phone.
Models Confirmed : V300L
We currently have firehose for V30.
Therefore, we can program UFS flash memory in 9008 mode.
It requires rawprogram?.xml(s) and patch?.xml(s) to program it.
It's easy to generate rawprogram?.xml(s) from kdz file, but generate patch?.xml(s) is not easy. (Unfortunately, I couldn't have time to generate patch?.xml(s)).
I have edited kdztools to generate rawprogram?.xml(s) easily (You can generate it by using "-r" argument. Currently, generate patch?.xml(s) is not supported. I'll add it soon).
I used patch?.xml(s) in post. it works well, but boot loop in the LG Logo.
However, it was possible to enter download mode.
------------------- GUIDE -------------------1. Download rawprogram?.xml patch?.xml with images from link. (It uses V300L30h000906.kdz)
2. Download firehose (prog_ufs_firehose_8998_lgev30.elf) from link.
<< Linux >>
3. Build qdl or download pre-built binary
4. Extract zip or tar.gz files 1, 2, 3 in any folder.
5. Run
Code:
$ ./qdl --storage ufs prog_ufs_firehose_8998_lgev30.elf rawprogram0.xml patch0.xml rawprogram1.xml patch1.xml rawprogram2.xml patch2.xml rawprogram3.xml patch3.xml rawprogram4.xml patch4.xml rawprogram5.xml patch5.xml rawprogram6.xml patch6.xml
in the terminal.
6. If LG logo shows, enter to the download mode.
<< Windows >>
3-6. You can program by QFIL similar as qdl.
7. Connect to any Windows PC with LGUP (must support Android Pie).
8. Flash kdz with ChipErase. (IMPORTANT)
9. If it boots successfully, your device has unbricked.
Click to expand...
Click to collapse
thank you so much,but can't download zip from this website,if you can offer other download way,such as google,mega,onedrive,i will apreciate it so much,thanks for your work
Johoneycn said:
thank you so much,but can't download zip from this website,if you can offer other download way,such as google,mega,onedrive,i will apreciate it so much,thanks for your work
Click to expand...
Click to collapse
Sorry for the late reply
mega. nz/#!zCZBkC4D!Vxo9wrd1c9vsZgCfQIrLelcp3unTY7sJAqMXjANvzjQ is V30_UNBRICK.zip
and mega. nz/#!PLIBzQ6L!JKtfq_RH2iFgcQckkRi_LtZGt9u2zaO2YF6x8dtHL6A is a firehose.
It is a shame we resort to such lengths for this. Shame on vendors. It is like pure gold or diamonds when we come across a programmer...
Hi, @quickwshell, could you see this: Help! bootloop per 5 sec, cannot enter rec, download or fastboot. Does the problem I'm facing now is what your method targeting to?
@quickwshell
Thank you so much for sharing firehorse for v30 and this solution. I have LS998 bricked bootloop after interrupting upgrade as @zacox123. I tried your files posted but still phone cant get download mode. Now Im trying to create rawprogram.xml and patch.xml from specific firmware model ls998 but I want to know what partitions are necesary just for getting download mode and then try to upgrade for usb mode.
Could you please help me?
thanks in advance
Pulian said:
@quickwshell
Thank you so much for sharing firehorse for v30 and this solution. I have LS998 bricked bootloop after interrupting upgrade as @zacox123. I tried your files posted but still phone cant get download mode. Now Im trying to create rawprogram.xml and patch.xml from specific firmware model ls998 but I want to know what partitions are necesary just for getting download mode and then try to upgrade for usb mode.
Could you please help me?
thanks in advance
Click to expand...
Click to collapse
How did you do with your phone? Have you made your phone into 9008 mode? Did you use the correct tool?
I have not processed my problem yet. But I read some other posts introducing that, use qpst or miracle box or any similar tools with the edl file provided by @quickwshell to flash in twrp directly, instead of getting download mode back. Maybe you can have a trial.
I was converting my lg [email protected] for unlocking. I have tools for flashing and I did it before with others phones. Accidently flashing process was interrupted and phone got that condition, no download mode. Now I'm using testpoint connection and UMT (tool for repair Qualcomm Phones) for trying to recover download mode. I suppose you can use QFIL for programming after we have correct rawprogramer.xml and patch.xml. Let me finish my test and I'll post results.
Pd: bootloader is not unlocked and I don't know if I can write twrp and it'll work.
Could you share links referring this topic and phone? Thanks.
Well, it definitely worked :good:.
Partitions extracted from us998 firmware
. Now I'm flashing again.
Pd: sorry for inverted picture. I make it from cellphone without edition
Do we need any special process before the computer work, @quickwshell and @Pulian? Is any special cable or teardown work needed? I have never used 9008 before but see other brands like xiaomi cannot simply enter 9008 mode directly.
---------- Post added at 04:27 PM ---------- Previous post was at 04:08 PM ----------
Pulian said:
Well, it definitely worked :good:.
Partitions extracted from us998 firmware
. Now I'm flashing again.
Pd: sorry for inverted picture. I make it from cellphone without edition
Click to expand...
Click to collapse
I see octoplus in your pic. Could you please share your tools and detailed steps? I have never tried 9008, so I hope some extra hand-by-hand instructions. Thanks.
The post I read is from an Android community app, and I'm afraid I cannot provide a link to it. And the author of that post said he had not tested yet, just some common sense and rough idea. I'd hear more from you, afterwards you have succeeded.
Thanks again @quickwshell. Firehorse file is the most important think for starting.
1. I extracted files partitions from firmware KDZ using this software https://forum.xda-developers.com/showthread.php?t=2600575
2.. I used testpoint for getting EDL (QUALCOM 9008) connection. https://forum.xda-developers.com/showpost.php?p=78573920&postcount=2
3. I tried firmware posted here without success (Maybe it works on others). So I wrote critical partitions extracted from my specific firmware (US998) using UMT box and I didnt need to create .xml files because this tool can read and detect internal partitions.
4. I got download mode and just write firmware by USB using octoplusbox. Phone Alive!!
I think every step here can be replaced using diferent software. good luck!
nate0 said:
It is a shame we resort to such lengths for this. Shame on vendors. It is like pure gold or diamonds when we come across a programmer...
Click to expand...
Click to collapse
yes,i think so too, lg is too bad on the software
Pulian said:
Thanks again @quickwshell. Firehorse file is the most important think for starting.
1. I extracted files partitions from firmware KDZ using this software https://forum.xda-developers.com/showthread.php?t=2600575
2.. I used testpoint for getting EDL (QUALCOM 9008) connection. https://forum.xda-developers.com/showpost.php?p=78573920&postcount=2
3. I tried firmware posted here without success (Maybe it works on others). So I wrote critical partitions extracted from my specific firmware (US998) using UMT box and I didnt need to create .xml files because this tool can read and detect internal partitions.
4. I got download mode and just write firmware by USB using octoplusbox. Phone Alive!!
I think every step here can be replaced using diferent software. good luck!
Click to expand...
Click to collapse
After getting download mode back, do we need chiperase like @quickwshell mentioned? I don't know if octoplusbox did it before writing firmware and I suppose most people would still use LGUP for firmware writing. Did you lose s/n, imei, etc. after phone booting? If not, I guess partition dl should be OK.
I didnt touch imei and security partitions. My phone worked after flashing without problems.
Pulian said:
Thanks again @quickwshell. Firehorse file is the most important think for starting.
1. I extracted files partitions from firmware KDZ using this software https://forum.xda-developers.com/showthread.php?t=2600575
2.. I used testpoint for getting EDL (QUALCOM 9008) connection. https://forum.xda-developers.com/showpost.php?p=78573920&postcount=2
3. I tried firmware posted here without success (Maybe it works on others). So I wrote critical partitions extracted from my specific firmware (US998) using UMT box and I didnt need to create .xml files because this tool can read and detect internal partitions.
4. I got download mode and just write firmware by USB using octoplusbox. Phone Alive!!
I think every step here can be replaced using diferent software. good luck!
Click to expand...
Click to collapse
I searched a lot for UMT Box and it seems like one has to collect it with the dongle or else it's not gonna work. Getting frustrated here Are there any way other than umt? Can you or anyone suggest?
moyedchowdhury said:
I searched a lot for UMT Box and it seems like one has to collect it with the dongle or else it's not gonna work. Getting frustrated here Are there any way other than umt? Can you or anyone suggest?
Click to expand...
Click to collapse
use cracked miracle box
seloka180 said:
use cracked miracle box
Click to expand...
Click to collapse
THANKS FOR COMING BACK. Mine is a LS998 converted into US998.
I'm So disappointed right now. Past few days have been unbearable. Even my Blood pressure is getting high
I'll describe what happened so that the situation is understood and you could suggest accordingly.
*I unlocked bootloader by wtf method.
*Tried several roms.
*Decided to stay on LOS 17.1 Q [Nearly got f*****g everything]
*Flushed a module via magisk which offered pixel boot animation(actually was searching for smartpixel to turn off 50% pixels)
*Rebooted and the device stuck into bootloop
*Rebooted into fastboot mode and reinstalled twrp and reboot- No luck
*Used a guide to wipe different partitions via fastboot and then reinstall twrp. Success but still boot stuck.
*Tried to go into download mode by pressing volume up while connecting USB, went into the mode but "waiting for any connection..." showed and was not detected by device mgr.
*Thought relocking the bootloader might get me into download mode.(That's when I burnt my luck I guess...)
*Did lock the bootloader.
*Aaaand still not detected in device manager.
*Moreover, now showing that Your device has failed a routine security check and will not boot!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
*Opened the back and test pointed motherboard, detected in 9008 mode
*Tried QFIL with V30_Unbrick.zip, sahara error.
*Tried a bunch of other tools most of them were so old that they didn't even have the firehose for this model.
Please someone help.
seloka180 said:
use cracked miracle box
Click to expand...
Click to collapse
Can't thank you enough mate! Used it and miracle did happen. I even tried to use it before but after you said it, I tried hard this time. Searched here and there, then took some risk and started to do things like this way -
I had V30_UNBRICK.zip unzipped in a folder with firehose and xml files.
*Disable defender or any other antivirus. (Normally not recommended, but it's the first thing I do when doing these things, also I have an extra laptop where I do all these which doesn't have any private or necessary files, never had any problem though).
*Also, disable driver signature enforcement on Windows(https://windowsreport.com/driver-signature-enforcement-windows-10/)
1. I searched and found Miracle box Thunder v2.93 with loader (No box needed)
2. Select Qualcomm, then flashing and Write Flash.
3. Untick the auto button beside firehose.
4. Under "write flash"
see this image
i. Select firehose, this doesn't recognize the .elf file so renamed it to .mbn (finger was crossed) and it worked!
ii. There are six rawprogram?.xml and patch?.xml (Here, ? = 1, 2, 3....6), I only used rawprogram0.xml and
iii. patch0.xml
5. Got everything ready and then detached the phone from cable.
6. Pressed the start button right after entering into Testpoint EDL Mode. The process starts and failed after a while due to missing files. Then I matched which files were present corresponding to the lines in the xml file, after that deleted all the extra lines(i. e. file was not present in the V30_UNBRICK.zip) from rawprogram0.xml and saved the file (patch0.xml was untouched). I used Notepad++ for editing.
7. Again detached the phone, detached battery, reattached battery, pressed the start button right after I shorted the edl test points, even before the device was detected in the device manager, no delay.
8. The process was completed, files flashed. These files were flashed so that we can now flash proper kdz with download mode. Do not turn on the phone. Or else you'll get into bootloop.
9. Detached the battery, shorted power button for a while(skip if you don't understand), reattached the battery.
10. Pressed volume up and inserted USB cable. Not detected first time. Detached and reattached with pressing volume up button hard this time.
11. witnessed one of the happiest moment seeing it was detected as an LG device in device manager. Wasn't 100% sure yet.
12. Flashed chiperase(important) with patched LGUP in dev mode. And it was done.
13. I will upload the XML file, you can use it with the existing files inside V30_UNBRICK.zip.
the xml file here
Before doing all that I spent five horrific days searching for a solution and almost ordered a motherboard from Aliexpress with a price tag of $100. I tried to be as elaborative as possible so that whoever next encounter the issue don't have to go through what I experienced past few days. If you're reading this and having a problem understanding anything, read again, repeat 10 times, then repeat more 10 times(worked for me), still no solution? knock me here (also: [email protected]). I could help you(with v 30, g6) remotely if I have time, no charges, donate if you will and if you don't I'll still be happy to help. Keep flashing, peace.
---------- Post added at 05:36 AM ---------- Previous post was at 04:57 AM ----------
quickwshell said:
If you try this method, I nor anybody else is responsible for any further damage done to your phone.
Models Confirmed : V300L
We currently have firehose for V30.
Therefore, we can program UFS flash memory in 9008 mode.
It requires rawprogram?.xml(s) and patch?.xml(s) to program it.
It's easy to generate rawprogram?.xml(s) from kdz file, but generate patch?.xml(s) is not easy. (Unfortunately, I couldn't have time to generate patch?.xml(s)).
I have edited kdztools to generate rawprogram?.xml(s) easily (You can generate it by using "-r" argument. Currently, generate patch?.xml(s) is not supported. I'll add it soon).
I used patch?.xml(s) in post. it works well, but boot loop in the LG Logo.
However, it was possible to enter download mode.
------------------- GUIDE -------------------1. Download rawprogram?.xml patch?.xml with images from link. (It uses V300L30h000906.kdz)
2. Download firehose (prog_ufs_firehose_8998_lgev30.elf) from link.
<< Linux >>
3. Build qdl or download pre-built binary
4. Extract zip or tar.gz files 1, 2, 3 in any folder.
5. Run
Code:
$ ./qdl --storage ufs prog_ufs_firehose_8998_lgev30.elf rawprogram0.xml patch0.xml rawprogram1.xml patch1.xml rawprogram2.xml patch2.xml rawprogram3.xml patch3.xml rawprogram4.xml patch4.xml rawprogram5.xml patch5.xml rawprogram6.xml patch6.xml
in the terminal.
6. If LG logo shows, enter to the download mode.
<< Windows >>
3-6. You can program by QFIL similar as qdl.
7. Connect to any Windows PC with LGUP (must support Android Pie).
8. Flash kdz with ChipErase. (IMPORTANT)
9. If it boots successfully, your device has unbricked.
Click to expand...
Click to collapse
Thank you, Your post helped me to understand a lot of things. Without whome I'd be having an expensive brick which can't even be used to build anything.
This is the way I recovered. So posting it here for people might get help.
seloka180 said:
use cracked miracle box
Click to expand...
Click to collapse
Can't thank you enough mate! Used it and miracle did happen. I even tried to use it before but after you said it, I tried hard this time. Searched here and there, then took some risk and started to do things like this way -
I had V30_UNBRICK.zip unzipped in a folder with firehose and xml files.
*Disable defender or any other antivirus. (Normally not recommended, but it's the first thing I do when doing these things, also I have an extra laptop where I do all these which doesn't have any private or necessary files, but never had any problems).
*Also, disable driver signature enforcement on Windows(https://windowsreport.com/driver-sig...nt-windows-10/)
1. I searched and found Miracle box Thunder v2.93 with loader (No box needed)
2. Select Qualcomm, then flashing and Write Flash.
3. Untick the auto button beside firehose.
4. Under "write flash"
see this image
i. Select firehose, this doesn't recognize the .elf file so renamed it to .mbn (finger was crossed) and it worked!
ii. There are six rawprogram?.xml and patch?.xml (Here, ? = 1, 2, 3....6), I only used rawprogram0.xml and
iii. patch0.xml
5. Got everything ready and then detached the phone from cable.
6. Pressed the start button right after entering into Testpoint EDL Mode. The process starts and failed after a while due to missing files. Then I matched which files were present corresponding to the lines in the xml file, after that deleted all the extra lines(i. e. file was not present in the V30_UNBRICK.zip) from rawprogram0.xml and saved the file (patch0.xml was untouched). I used Notepad++ for editing.
7. Again detached the phone, detached battery, reattached battery, pressed the start button right after I shorted the edl test points, even before the device was detected in the device manager, no delay.
8. The process was completed, files flashed. These files were flashed so that we can now flash proper kdz with download mode.
9. Detached the battery, shorted power button for a while(skip if you don't understand), reattached the battery.
10. Pressed volume up and inserted USB cable. Not detected first time. Detached and reattached with pressing volume button hard this time.
11. witnessed one of the happiest moment seeing it was detected as an LG device in device manager. Wasn't 100% sure yet.
12. Flashed chiperase(important) with patched LGUP in dev mode. And it was done.
13. I will upload the XML file, you can use it with the existing files inside V30_UNBRICK.zip.
the xml file here
Before doing all that I spent five horrific days searching for a solution and almost ordered a motherboard from Aliexpress with a price tag of $100. I tried to be as elaborative as possible so that whoever next encounter the issue don't have to go through what I experienced past few days. If you're reading this and having a problem understanding anything, read again, repeat 10 times, then repeat more 10 times(worked for me). Keep flashing, peace.
Please, where can I find ME372CG files for xFSTK?
I want to restore bootloader of my ME372CG tablet.
I follow these instructions, which are for FE170CG:
https://forum.xda-developers.com/android/help/asus-fonpad-7-fe170cg-bricked-stuck-t3740819
But I did not find ME372CG files for xFSTK.
So I took them from official Asus ME372CG firmware (from UL-K00E-WW-7.6.0.0-user.zip).
I found different file names in ifwi folder and I am not sure, which to use fo xFSTK:
dnx_fwr_ctp_???.bin
ifwi_ctp_???.bin
CLVP_CSAB_FWR_DnX_20.29.bin
ME372CG_32_IFWI_v54.57_CSAB_PROD.bin
I could not find any Softfuse file either.
Most probably I do not have the correct files, because xFSTK download does not work.
The file names, which I used, and the result from xFSTK can be found here:
https://www.dropbox.com/s/cz8imzdrs1r551r/xFSTK_ME372CG files.JPG?dl=0
Where can I find the correct files for xFSTK?
Thank you very much.
Greetings from Slovakia
Juraj
---
Cause of malfunction:
My tablet reported some kind of UI error, so I restarted it (still within Android),
but it never started again. It just vibrates when switching on, always black screen (only almost unnoticeable flash of light on LCD, during switching on). The battery is full - I measured it.
Use this file, run as Administrator ME372CG Debrick.bat and connect your device.
https://gofile.io/d/P6Ja57
After that flash this raw file with asus flash tool and make sure to select right model name.
http://www.mediafire.com/file/fhtkb..._V11.2.3.33-raw_2015_SmartPhones.How.zip/file
Good Luck
Teddy Lo said:
Use this file, run as Administrator ME372CG Debrick.bat and connect your device.
https://gofile.io/d/P6Ja57
After that flash this raw file with asus flash tool and make sure to select right model name.
http://www.mediafire.com/file/fhtkb..._V11.2.3.33-raw_2015_SmartPhones.How.zip/file
Good Luck
Click to expand...
Click to collapse
Hey Teddy, The link has been expired! Can you upload it again?
I need FW DnX, IFWI, OS DnX for fonepad 7 ME372CG (K00e)
sid.1375 said:
Hey Teddy, The link has been expired! Can you upload it again?
I need FW DnX, IFWI, OS DnX for fonepad 7 ME372CG (K00e)
Click to expand...
Click to collapse
Hi, I received some suggestions from Teddy, but it did not work for me.
(I re-uploaded the files to Dropbox, so the links should work):
1. Download this zip: https://www.dropbox.com/s/1s5i85hd22yqlct/CSC_ME372CG_Debrick.7z?dl=0
2. Extract with 7-zip on your Desktop
3. Open extracted CSC_ME372CG_Debrick file ---> Right click on ME372CG Debrick.bat left click on Run as Administrator. And it should look like this:
https://www.dropbox.com/s/e3yulpxt70rn6ly/non-Administrator ME372CG Debrick.bat.png?dl=0
If that doesn't show up install this minimal adb and fastboot command
https://www.dropbox.com/s/zgr1ljdm13owlrs/minimal_adb_fastboot_v1.4.1_setup.exe?dl=0
Here is tutorial how to install:
https://forum.xda-developers.com/showthread.php?t=2317790
4. If the tool doesn't recognise your device press VOL + or VOl - and connect your device with pc while you are holding one of volume buttons.....
===
After I informed Teddy that it does not work for me,
he suggested this:
See this tutorial for another device to get the point, reinstall drivers and try again debrick files. Softfuse file I can't find for your device but with debrick.bat is trick for seconds I thing to get recognized to start flashing partition and firmware....
https://www.youtube.com/watch?v=xuD39TjQJGo
or buy package and download files for XFSTK.
https://easy-firmware.com/index.php?a=downloads&b=file&id=100391
(I have not bought those xFSTK files yet, but I will try it later this week and let you know.)
Juraj
jurajhotovy said:
Hi, I received some suggestions from Teddy, but it did not work for me.
(I re-uploaded the files to Dropbox, so the links should work):
1. Download this zip: https://www.dropbox.com/s/1s5i85hd22yqlct/CSC_ME372CG_Debrick.7z?dl=0
2. Extract with 7-zip on your Desktop
3. Open extracted CSC_ME372CG_Debrick file ---> Right click on ME372CG Debrick.bat left click on Run as Administrator. And it should look like this:
https://www.dropbox.com/s/e3yulpxt70rn6ly/non-Administrator ME372CG Debrick.bat.png?dl=0
If that doesn't show up install this minimal adb and fastboot command
https://www.dropbox.com/s/zgr1ljdm13owlrs/minimal_adb_fastboot_v1.4.1_setup.exe?dl=0
Here is tutorial how to install:
https://forum.xda-developers.com/showthread.php?t=2317790
4. If the tool doesn't recognise your device press VOL + or VOl - and connect your device with pc while you are holding one of volume buttons.....
===
After I informed Teddy that it does not work for me,
he suggested this:
See this tutorial for another device to get the point, reinstall drivers and try again debrick files. Softfuse file I can't find for your device but with debrick.bat is trick for seconds I thing to get recognized to start flashing partition and firmware....
https://www.youtube.com/watch?v=xuD39TjQJGo
or buy package and download files for XFSTK.
https://easy-firmware.com/index.php?a=downloads&b=file&id=100391
(I have not bought those xFSTK files yet, but I will try it later this week and let you know.)
Juraj
Click to expand...
Click to collapse
I tried that but it didn't work. Actually it's because we lost fastboot and droidboot.
About those xFSTK files, we can acquire them from rom (zip/raw). there is a zip file called "ifwi.zip" in the rom package.
I follow this tutorial to debrick it but I didn't make it:crying:
sid.1375 said:
I tried that but it didn't work. Actually it's because we lost fastboot and droidboot.
About those xFSTK files, we can acquire them from rom (zip/raw). there is a zip file called "ifwi.zip" in the rom package.
I follow this tutorial to debrick it but I didn't make it:crying:
Click to expand...
Click to collapse
Hi
Finally, did you can find a solution for K00E?
miter8 said:
Hi
Finally, did you can find a solution for K00E?
Click to expand...
Click to collapse
Unfortunately no.
Sorry for the late response.
First of all I want to thank @zogu without him, this guide would not be possible, This guide is for phones with Hard Brick, where the bootloader is destroyed and there are no tools that recognize the phone as odin
When you connect phones without a bootloader, Windows detects them as exynos9820 in device manager.
All of this is accomplished by trial / error method
I repaired my g975f and I have U3 and U8 files only for this model, but I will try to explain how to prepare files for any other model.
We have to use the same bootloader version that was previously on the phone, or if you're not sure, use the latest sboot.bin.
Plug in the phone and press and hold the power button.
Windows will detect the exynos9820 device, install the driver:
click manually,
com and lpt ports,
select the Driver Exynos USB Mode folder
Now we have to copy
WinDNWApi.dll
in:
C: \ Program Files \ Samsung \ Exynos USB Driver \ Drivers
There probably isn't this folder, just create it and copy the files.
Now we have to create the boot files.
Using lz4 1.9.2 we can unzip the sboot.bin.lz4 to sboot.bin and then be able to edit it, everything is explained in a guide inside the file
Download the last sboot.bin that was on your device
Now you have to extract the partitions from this file
In some hex editor, create 4 files and extract from sboot.bin
0x3000 is BL1 name> bl1
0x3000 ... 0x17000 is epbl
0x17000 ... 0x68000 is BL2
0x7e000 ... 0x7eb000 + 0x190000 = 0x1fe000 sboot
Dram_training do not need to be cut, it is not used in flashing
0x244000 ... 0x1BD000 is el3mon dram
Launch multiuploader.exe
Plug in the phone and press and hold the power button.
Search and find script.cfg
click start and the phone will go into odin mode.
Start odin and flash the firmware (in case of having split the stock rom sboot) or Combination (in case of having split the combination sboot)
the z-zip tool must be downloaded
Binary editor - Multidownload flash tool with files for sm-g975f u8 x32, x64,
https://drive.google.com/file/d/1GzgqNCCEE0e43CniitzuAxKcDax5QLaT/view?usp=sharing
link is restricted
Bro. Share file pls on your googledrive. We cantdownload it
Flar4eg said:
Bro. Share file pls on your googledrive. We cantdownload it
Click to expand...
Click to collapse
Excuse me, is that I uploaded the files to my google drive cloud and I detect a dll, or part of the flashtool as a virus, now I upload it again and put the link
https://mega.nz/file/eWRkiCwI#XP0yMOiBsfkUKIoxhKaZkLIgdhkwnEtiyVHqixMu8NI
multiuploader error: WinDNWApi.dll file could not be found.
Skyfall191299 said:
In some hex editor, create 4 files and extract from sboot.bin
0x3000 is BL1 name> bl1
0x3000 ... 0x17000 is epbl
0x17000 ... 0x68000 is BL2
0x7e000 ... 0x7eb000 + 0x190000 = 0x1fe000 sboot
Dram_training do not need to be cut, it is not used in flashing
0x244000 ... 0x1BD000 is el3mon dram
Click to expand...
Click to collapse
can anybody please explain how to make these files I have my Sboot.bin which was in the phone, I don't understand how to use hex editor. can some plz assist me, working on a750g. broke bootloader by flashing wrong firmware a750f after MDM bypass. software ver U1ARL3 for sboot
here is my sboot, can someone please create or show me how to create with hex https://drive.google.com/file/d/1CcEqe4MH__APK7H42aP3H2KGdqkAi-xx/view?usp=sharing
Skyfall191299 said:
https://mega.nz/file/eWRkiCwI#XP0yMOiBsfkUKIoxhKaZkLIgdhkwnEtiyVHqixMu8NI
Click to expand...
Click to collapse
getting error that el3mon_dram not found. can you help me?
Hello someone has the files ? The download link is inactive
The download link is inactive, please active or reupload please.
Skyfall191299 said:
First of all I want to thank @zogu without him, this guide would not be possible, This guide is for phones with Hard Brick, where the bootloader is destroyed and there are no tools that recognize the phone as odin
When you connect phones without a bootloader, Windows detects them as exynos9820 in device manager.
All of this is accomplished by trial / error method
I repaired my g975f and I have U3 and U8 files only for this model, but I will try to explain how to prepare files for any other model.
We have to use the same bootloader version that was previously on the phone, or if you're not sure, use the latest sboot.bin.
Plug in the phone and press and hold the power button.
Windows will detect the exynos9820 device, install the driver:
click manually,
com and lpt ports,
select the Driver Exynos USB Mode folder
Now we have to copy
WinDNWApi.dll
in:
C: \ Program Files \ Samsung \ Exynos USB Driver \ Drivers
There probably isn't this folder, just create it and copy the files.
Now we have to create the boot files.
Using lz4 1.9.2 we can unzip the sboot.bin.lz4 to sboot.bin and then be able to edit it, everything is explained in a guide inside the file
Download the last sboot.bin that was on your device
Now you have to extract the partitions from this file
In some hex editor, create 4 files and extract from sboot.bin
0x3000 is BL1 name> bl1
0x3000 ... 0x17000 is epbl
0x17000 ... 0x68000 is BL2
0x7e000 ... 0x7eb000 + 0x190000 = 0x1fe000 sboot
Dram_training do not need to be cut, it is not used in flashing
0x244000 ... 0x1BD000 is el3mon dram
Launch multiuploader.exe
Plug in the phone and press and hold the power button.
Search and find script.cfg
click start and the phone will go into odin mode.
Start odin and flash the firmware (in case of having split the stock rom sboot) or Combination (in case of having split the combination sboot)
the z-zip tool must be downloaded
Binary editor - Multidownload flash tool with files for sm-g975f u8 x32, x64,
https://drive.google.com/file/d/1GzgqNCCEE0e43CniitzuAxKcDax5QLaT/view?usp=sharing
Click to expand...
Click to collapse
good jod
im follwed to this instruction but all links not woriking
pla give me ur telegram or whtas app
and upload files to the new link plz
eldon301 said:
can anybody please explain how to make these files I have my Sboot.bin which was in the phone, I don't understand how to use hex editor. can some plz assist me, working on a750g. broke bootloader by flashing wrong firmware a750f after MDM bypass. software ver U1ARL3 for sboot
here is my sboot, can someone please create or show me how to create with hex https://drive.google.com/file/d/1CcEqe4MH__APK7H42aP3H2KGdqkAi-xx/view?usp=sharing
Click to expand...
Click to collapse
how to create with hex bro ?
links not woriking
link isn't working please fix
akbarshoxdedamirzayev said:
how to create with hex bro ?
Click to expand...
Click to collapse
Find the exact firmware that’s currently in the device, extract sboot from the firmware. You need to find correct location of bl1 bl2 el3 and others, names correspond to which is cut. You need 5 files from sboot. Am stuck on the forth file failing and I still don’t understand how to find them. What I did was follow others with exactly the same problem to see and understand how they got there’s and then tried it on my sboot. I am failing on part4 don’t even know how to make a cfg but from what I understand e for exynos and the number after so mine is e7885. Still not sure like I said
http://www.mediafire.com/file/sg5m2ti3k6a63z5/USB_Down_Load_32bit.zip/file download link
Skyfall191299 said:
First of all I want to thank @zogu without him, this guide would not be possible, This guide is for phones with Hard Brick, where the bootloader is destroyed and there are no tools that recognize the phone as odin
When you connect phones without a bootloader, Windows detects them as exynos9820 in device manager.
All of this is accomplished by trial / error method
I repaired my g975f and I have U3 and U8 files only for this model, but I will try to explain how to prepare files for any other model.
We have to use the same bootloader version that was previously on the phone, or if you're not sure, use the latest sboot.bin.
Plug in the phone and press and hold the power button.
Windows will detect the exynos9820 device, install the driver:
click manually,
com and lpt ports,
select the Driver Exynos USB Mode folder
Now we have to copy
WinDNWApi.dll
in:
C: \ Program Files \ Samsung \ Exynos USB Driver \ Drivers
There probably isn't this folder, just create it and copy the files.
Now we have to create the boot files.
Using lz4 1.9.2 we can unzip the sboot.bin.lz4 to sboot.bin and then be able to edit it, everything is explained in a guide inside the file
Download the last sboot.bin that was on your device
Now you have to extract the partitions from this file
In some hex editor, create 4 files and extract from sboot.bin
0x3000 is BL1 name> bl1
0x3000 ... 0x17000 is epbl
0x17000 ... 0x68000 is BL2
0x7e000 ... 0x7eb000 + 0x190000 = 0x1fe000 sboot
Dram_training do not need to be cut, it is not used in flashing
0x244000 ... 0x1BD000 is el3mon dram
Launch multiuploader.exe
Plug in the phone and press and hold the power button.
Search and find script.cfg
click start and the phone will go into odin mode.
Start odin and flash the firmware (in case of having split the stock rom sboot) or Combination (in case of having split the combination sboot)
the z-zip tool must be downloaded
Binary editor - Multidownload flash tool with files for sm-g975f u8 x32, x64,
https://drive.google.com/file/d/1GzgqNCCEE0e43CniitzuAxKcDax5QLaT/view?usp=sharing
Click to expand...
Click to collapse
Can you check the addresses and lenghts of the partitions cut out of sboot?
I think you've made a mistake.
Can give me the precise partition details?
Are you 100% positive that this is valid at least for most devices of the same chipset?
I'd like to try to make an automated script or a tool of some sort.
Also when I was dividing my A515F U5 sboot I've spotted some long breaks in data which I assumed were empty blocks at the end of partitions.
What confused me about it is that I didn't find those where you said partitions are ending.
Can you demonstrate graphically your partitions in a linear projection?
It’s been 3 years and still can’t get help with A750G hard brick. I guess XDA is not so friendly and helpful anymore.
The world is slowly dying. Peace to everyone who still cares
eldon301 said:
It’s been 3 years and still can’t get help with A750G hard brick. I guess XDA is not so friendly and helpful anymore.
The world is slowly dying. Peace to everyone who still cares
Click to expand...
Click to collapse
I'd like to help
NonStickAtom785 said:
I'd like to help
Click to expand...
Click to collapse
Hello my friend I am try to get life back into a A750G, it’s completely hard bricked showing exynos usb in device manager. Can i direct message you or should I keep it in the forums. I was falling on part 4 off the files needed to create, I didn’t even know if my cfg file was correct but I tried my best at understanding the creation of the files. Plz help my brothers