[Solved][Q] Phone detected as partitions only ? - Nokia X

Hi, I flashed my Nokia X with wrong zip from recovery. I think the phone is dead, when I connect the device to my linux pc, it's detected as partitions, there are many files in there of recovery, system,... and even my internal storage is detected (on windows nothing is detected). So when I plug the device in to my USB, the phone juste vibrates then nothing appear. Same thing when I remove battery then click power button. I hope anyone here can help me! Thank you for your support I really need my device back!

The problem is solved and this is the solution: http://forum.xda-developers.com/nokia-x/general/tutorial-how-to-revive-dead-nokia-x-t3000903

Related

Upgrade ROM code error

I've installed some ROMs before. Today's one, stucked at 20%, only possibility was to reset device. And - there is problem, after reseting I've chosen (by mistake) option by which phone memory should be erased. So now I got clean Internal memory, and no diamimg.nbh on it, so I don't know how to bring diamond to life.
Any help?
jusr make a reset with vol down pressed to enter bootloader mode, connect to computer and flash any rom with diamondcustomruu+.nbh file of the rom
Will diamondcustomruu see my phone if it can be started only in BootLoader mode? I'm connecting my phone in this mode to PC, however customRRU doesen't see it (windows does - it's recognized as qualcomm) .
EDIT: As for now, only possibility i see is connecting phone to USB host : http://wmpoweruser.com/?p=490 . Any other ideas?
EDIT2: OK. I've unchecked USB connection in ActiveSync to connect mtty. Flashing right now.
EDIT3: It did work. Diamond is alive. Problem SOLVED.

EMERGENCY Brick!

hi,
any help is hugely appreciated.
I wiped my phone in recovery with the option to wipe for new custom rom, this worked fine. when i went to install custom rom it failed and then turned itself off. now the phone just gets stuck at the Sony logo. the only way i can turn it off is via the red button in the sim slot.
I am unable to connect to the computer at all, no fastboot. I'm also unable to boot into recovery to restore.
Please help. Hope i haven't ****ed it up beyond fixing
Thanks
Flash a stock ftf with flashtool (in flashmode). You should definitely get into flashmode and fastboot, otherwise there is a problem with your computer.
Funny, I didn't even know there was a red button Holding Volume Up + Power for a few seconds always worked for me, no matter in which state the phone was.
Hi all,
I've exactely the same problem !!!
My phone stuck to Sony logo, and not reconyze on my 3 PC.... before that, usb connexion work fine on all PC, but now.... nothing
I've just POWER + and VOL+ (its power off the phone), i've no led color light
I've try flashboot, but not detect my phone
i've try to install :
flashtool-0.9.16.1-windows (not detected)
Flashtool-drivers-1.5-20140318 (my computer doesnt not see my phone)
Xperia_Z1_Compact_driver (my computer doesnt not see my phone too)
I can't go into Flashmode...
When i power off my Z1c, and i plug usb + (vol+) nothing appear...stuck Sony logo...
I'm lost... I need your help XDA members ! just U can help me
PS : the red button is in the SIM slot, but i think is same POWER + (VOL+).... its power off the phone
Because you're doing it wrong. Vol+ enters fastboot mode, you have to press Vol- to enter flashmode. Then use Flashtool to restore the firmware.
Iruwen said:
Because you're doing it wrong. Vol+ enters fastboot mode, you have to press Vol- to enter flashmode. Then use Flashtool to restore the firmware.
Click to expand...
Click to collapse
THX for your response !
Sorry it's a mistake....
I've try both (vol+ and USB) and (vol- and USB).... but no sound (device not detected), in device manager nothing appear too.
I've make a fresh install of windows 7 x64 on another PC.
I finaly working to boot (2-3 times) with Vol- + USB cable, but stay in sony logo and Flashtool whait for device...
Please i need u're help beacause i'm really lost (usualy i flash many phone S4, Mediatek, phones, etc...) but now i dont find solution
My problem come from the original cable
All this because of the USB cable does not work ... CRAZY !
This USB cable is new and original sony... just 2 Weeks
I solved my problem with new one
That's unfortunate, good you found the issue.

[Q] Please help!! Find7 boot without screen!! (bricked!)

Hi,
I was flash new version rom 2.0.8i and I boot into recovery , but I wipe all partitions....
and I reboot try to use tool-partition-repairscripts-for-oppo-find7-find7a
this tool to repair my partition, I boot into fastboot mode and run the tool , after almost 10 min my find7 has no response.
I remove the bettery and replace it, try to reboot again.
Now when I press power, it vibrate but no screen, just like not power on.
(tried to press vol+ and vol- , not work!)
How should I do to repair my Find7..... please help!
update.
When I press power and vol+ , plug usb to my computer
I found a new device named "ZEUS Flash Device"
Can I repair my find7 by this interface?
update 2.
after study, I found some post about "bricked"
I think I bricked my Find7.
So I tried to repair by some post like "guide-how-to-recover-your-bricked-find-7-7a.23067"
I got 2 device driver installed perfectly. (9008/9006??)
But when I reconnect and start the fix program, it stuck!
I can see a new "DISK DEVICE" in my windows disk manager.
But nothing happen in the fix program..
I wait over 5 min, and I give up.. (Almost AM4:00.. I need to work on AM7:00 OMG)
Today I will tried again to uninstall drivers and reboot windows , reinstall driver..
hope I can save my Find7..
BTW, I have other one smartphone and it is sony, so I have installed the driver for it, and the device interface called ZEUS...

Can't flash with SPflash, need help!

Hey there. I'mve having problems with installing TWRP on my P8000. What I've done:
Removed W7 drivers signature enforcement, reinstalled the drivers, and tried again running SPFlash. The programs opens, I select the scatter file from the the TWRP recovery folder. However, when I press Download, and connect the phone to the cable, nothing happens in the problem. Windows makes a sound of device connected, and lke 5 seconds later it makes the sound of device disconnected. After that the phone goes into that battery charging mode, and a battery appears in the screen.
Any thoughts on this?
Thank you
I would install TWRP via fastboot but to to answer your question: Is your phone turned off when connecting it to the PC and after you pressed download?

Water damaged OP3 only shows Tux at boot for 3 seconds (hard brick?)

Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Contact a software technician
juuz said:
hello,
i've got a water damaged op3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a linux logo (a small tux in the middle of the screen) and then turns off after 3 seconds. If i connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could i try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
Best regards and thanks in advance!
Click to expand...
Click to collapse
you better avoid doing experiments on op3. Symptoms you have mentioned in your thread, tells that your has been flashed (don't have usb drivers,no os,no firmware). I have faced same problem with my letv le 1s. It is a software problem. Your phone is totally empty. So do contact with any software technician, he uses sp flash tool to wake up the device. Download sp flash tool and follow procedure. If sp flash tool is detecting your device then it means your device hardware is fine.
juuz said:
Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Click to expand...
Click to collapse
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
tnsmani said:
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
Click to expand...
Click to collapse
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
juuz said:
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
Click to expand...
Click to collapse
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
tnsmani said:
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
Click to expand...
Click to collapse
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
juuz said:
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
Click to expand...
Click to collapse
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
tnsmani said:
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
Click to expand...
Click to collapse
No need to worry.. Of course, you couldn't know and there are a lot of people asking dump questions..
My phone is back a life, I guess the data transfer via USB is not working anymore, charging works although I needed to take my Oneplus One's battery (identical connector, just need to take care of the pin layout [+/-]) because my OP3 battery is pretty low and I don't know if I can reactivate it.. It has about 3,4V at the moment and charges very slow..
Finally, if anyone else faces this issue and can't boot his phone:
Try different button combinations and keep holding the buttons several seconds/minutes..

Categories

Resources