So my USB Port is broken. I use this phone as my back up. Also just swap out batteries. However I was wondering how easy/hard would it be to replace the USB Port. Has any else looked into doing this?
Related
I have an E4GT and my USB port is being fickle. It doesn't connect unless I hold the cable in a strange upward tilt position.
In order to rule out any software cause for this, I ODIN'd back to stock but that didn't change anything. I tried all sorts of different USB cables (stock cable, monoprice cable, HTC cable) but no dice.
Anyone have this problem? is the USB port portion soldered on the motherboard or can it be replaced easily?
Guys I've have had problems with my original micro usb cable, it was not charging my phone anymore so I replaced with another micro usb cable. Now my device charges just fine, but when i plug my phone to computer it doesn't sees it anymore. It was fine 2-3 days ago. Why would that be? I didn't change or do anything. Is it something relevant to usb port pins? Any chance that they might be broken?
Edit: I've just googled about this problem and saw Xperia X10 has a lot of problems about loose usb port. I'm thinking same thing about my Xperia S.
75% loose usb port
sorry
I'm not able to get to the bootloader screen because the front usb port is not functioning on my unit. Has anyone been able to use one of the USB ports on the back to get to ADB and/or get to the bootloader? Is this a known issue with a workaround? I've done quite a bit of searching and have not turned up any solutions. Considering what is involved in shipping this back, I'd much rather figure something out. Thanks in advance for any help!
Edit: I should mention that I have used the adbon password and it does acknowledge that adb has been enabled. Just nothing seems to work on the front port. When I connect my Linux machine and run lsusb nothing shows for the unit. I have considered buying or making a USB-A to USB-A cable to connect my computer to one of the back USB ports, but I'm concerned about how these back USB ports are designed. Is it as simple as a built-in OTG cable? If so I'm probably fine. If it is more like a computer's USB port I could damage my laptop, my headunit, or both. I'd really like to hear if anyone else has had to deal with this. Unfortunately I haven't verified if the front USB will charge a phone. This is my next step.
dutchhome said:
I'm not able to get to the bootloader screen because the front usb port is not functioning on my unit. Has anyone been able to use one of the USB ports on the back to get to ADB and/or get to the bootloader? Is this a known issue with a workaround? I've done quite a bit of searching and have not turned up any solutions. Considering what is involved in shipping this back, I'd much rather figure something out. Thanks in advance for any help!
Edit: I should mention that I have used the adbon password and it does acknowledge that adb has been enabled. Just nothing seems to work on the front port. When I connect my Linux machine and run lsusb nothing shows for the unit. I have considered buying or making a USB-A to USB-A cable to connect my computer to one of the back USB ports, but I'm concerned about how these back USB ports are designed. Is it as simple as a built-in OTG cable? If so I'm probably fine. If it is more like a computer's USB port I could damage my laptop, my headunit, or both. I'd really like to hear if anyone else has had to deal with this. Unfortunately I haven't verified if the front USB will charge a phone. This is my next step.
Click to expand...
Click to collapse
My front USB also doesn't work. I even got mini to standard USB cable with unit, but plugging flash drive into it doesn't produce any reslt.
I also plugged extension cable to one of back USB ports and tried it (plugibg same USB flash) but it doesn't work either.
So I'm also confused.
Does that mean you are still running the stock ROM? I have been hesitant to install the custom ROM because they say you must be able to get into the bootloader even though I couldn't find a step in the process that required it.
Regarding the USB ports not working at all, you may find that you need to use a powered USB hub. I've seen reports of USB devices acting up due to the low power. This is one of the reasons I thought it might be safe to use the rear ports with my computer. (My first real test is going to be mangling a male-to-male USB cable so only the data lines are connected to see if I can get those rear USB ports to talk to the computer. I figure that way there is no chance of frying any circuits.. Each side already has its own power and I don't believe any signaling is sent via the power pins.)
On my unit (MTCB-KGL-V2.80), I have used a T-Mobile USB broadband modem successfully on the rear port, so I know rear ports are live. I did take it apart to see if something was obviously wrong with the front port, but nothing jumped out at me.
So I have a bit more information on my headunit. BTW, I have the BMW E46 model with MCU MTCB-KGL-V2.80.
On my system, both the front USB port and the rear 3G USB port are wired as device ports connected to an AU6258 USB controller (http://www.sunnyqi.com/upLoad/product/month_1403/201403162331285643.pdf). I don't remember exactly which USB ports they are connected to, but I believe the 3G port is connected to port 2 (pins 6 & 7) and the front USB port is connected to either ports 3 or 4 (pins 9 & 10 or 11 & 12 respectively). Nothing is connected to port 1 or to the upstream port. The other rear USB port is wired directly to the MTC_RK3188 board.
All three ports are wired with only four pins, so I'm concerned that none of them could work with the computer. The USB controller doesn't have USB ID pins, so does that mean that the 4 downstream ports are OTG and the upstream port is for a computer? Unfortunately I don't know the hardware side.
dutchhome said:
Does that mean you are still running the stock ROM? I have been hesitant to install the custom ROM because they say you must be able to get into the bootloader even though I couldn't find a step in the process that required it.
Regarding the USB ports not working at all, you may find that you need to use a powered USB hub. I've seen reports of USB devices acting up due to the low power. This is one of the reasons I thought it might be safe to use the rear ports with my computer. (My first real test is going to be mangling a male-to-male USB cable so only the data lines are connected to see if I can get those rear USB ports to talk to the computer. I figure that way there is no chance of frying any circuits.. Each side already has its own power and I don't believe any signaling is sent via the power pins.)
On my unit (MTCB-KGL-V2.80), I have used a T-Mobile USB broadband modem successfully on the rear port, so I know rear ports are live. I did take it apart to see if something was obviously wrong with the front port, but nothing jumped out at me.
Click to expand...
Click to collapse
No I flashed Malaysk ROM from GPS SD card. No problems. Just follow instruction. I had luck that I didn't need to recover from USB.
Did you tried with USB powered hub? I don't have one to try it myself.
RK3188 1024x600 front USB not working confirmed
pa.ko said:
My front USB also doesn't work. I even got mini to standard USB cable with unit, but plugging flash drive into it doesn't produce any reslt.
I also plugged extension cable to one of back USB ports and tried it (plugibg same USB flash) but it doesn't work either.
So I'm also confused.
Click to expand...
Click to collapse
I checked on my Linux workstation with
Code:
lsusb |wc -l
plugging and unplugging all three USB cables and the number did not change. BTW where did you use the "adbon" command? The only place that I could even try was at Settings > Factory Settings. Regards Flint
Hi all!
My computers USB port was broken and it let all the electric through (don't know how to write these thing in english)
I connect my phone to the USB and don't know that.. then my phone only charge through computers usb and pc doesn't even try to recognize it.
Then i connected my microsd cardreader to same usb and i heard "puff" and smelld burning electric.
Phone does not smell like burned or anything. Working just fine.. it only doesn't work with data transfer.
So.. is it possible to fix by myself? like changing the usb dock https://ae01.alicdn.com/kf/HTB1xvUoMVXXXXaoaXXXq6xXFXXXf/5PCS-For-Xiaomi-Mi-Max-Hexa-Core-6-44-Smartphone-USB-Charging-Port-Dock-Connector-Transfer.jpg
Or is my phone bricked forever and i cant use it through usb cable?
i hope that you all understand my problem, it's hard to write these thing different language
Anyone?
Replacing the usb dock piece will probably fix your problem and isnt very hard to replace and isnt very expensive from aliexpress. I cant post links but if you go to youtube and search "mi max disassembly" it will show you how to take apart the phone and get to the piece. i have taken myn apart before and it isnt very hard at all. Hope this helps
Sorry, it's not clear to me. Is there a problem with the USB port on your phone? Or only a problem with the USB port on your computer?
You may want to try a different USB cable. Sometimes the microUSB adapters can get worn out.
Problem is on the phone. Phone only charge from usb. Settings are ok.
Same usb port broke my Canon also. It has warranty and its fixed now. It was same way broken than my phone.
Computers usb is fixed now.
I had been somewhat unlucky and while charging my beloved FLO something went puf (literally). After that I don't have any USB connectivity. Charging my N7 works (very slowly), but no USB OTG or USB ADB. OK Fine and dandy if I wouldn't be total idiot and wipe system while trying to install new ROM before transferring ROM image to internal storage.
Now I have FLO paper clip able to go to TWRP but can't install nothing. As far I understand there's no way to enable wifi in TWRP.
Any ideas what would needed to be replaced to make my FLO work again so I can put some ROM on it and make it work again.
I'm not sure if USB daughter board would suffice and solve my problem. Any suggestions?
jxl69 said:
I had been somewhat unlucky and while charging my beloved FLO something went puf (literally). After that I don't have any USB connectivity. Charging my N7 works (very slowly), but no USB OTG or USB ADB.
Click to expand...
Click to collapse
Either the USB port developed "dry joints" or the wide silver cable (LCM) needs to be re-seated on both connectors.
Disconnect the battery before fixing LCM cable. Here is advice on USB port repair.
Replacing the daughterboard PCB should be the last resort because it is unlikely that the touch function will work 100%. It would work if we had access to the touch calibration software - the problems are described here https://forum.xda-developers.com/ne...rivers-to-calibrate-touch-screen-usb-t3334898
k23m said:
Either the USB port developed "dry joints" or the wide silver cable (LCM) needs to be re-seated on both connectors.
Disconnect the battery before fixing LCM cable. Here is advice on USB port repair.
Replacing the daughterboard PCB should be the last resort because it is unlikely that the touch function will work 100%. It would work if we had access to the touch calibration software - the problems are described here https://forum.xda-developers.com/ne...rivers-to-calibrate-touch-screen-usb-t3334898
Click to expand...
Click to collapse
I doubt re-seating would help or cleaning USB port, since it was something electrical happening with that *puf*. If my memory serves me right there was a smell of burnt electronics. I doubt that some shortage disconnected any cables.
jxl69 said:
I doubt re-seating would help or cleaning USB port, since it was something electrical happening with that *puf*. If my memory serves me right there was a smell of burnt electronics. I doubt that some shortage disconnected any cables.
Click to expand...
Click to collapse
Sounds like you need a new charging port and board. Easy to fit but difficult to get hold of one. Maybe purchase a broken Flo on eBay and extract the charging port board
dave457 said:
Sounds like you need a new charging port and board. Easy to fit but difficult to get hold of one. Maybe purchase a broken Flo on eBay and extract the charging port board
Click to expand...
Click to collapse
Even tho charging works? The only problem is data part of USB connection. USB OTG will not work neither will it connect to a PC for file transfer/adb. But if connected to PC or plug device charges. I believe it will not charge past 80 or 90%.
jxl69 said:
Even tho charging works? .
Click to expand...
Click to collapse
Yes