Develop Bugs

[Q] Soft Bricked? i747 help

hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.

mtsosie said:
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
Click to expand...
Click to collapse
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have

Ok, so I also wasn't able to get into recovery.
I decided to flash cwm via odin. After it flashed the phone rebooted and turned on normally. I have turned it on and off like 5 times and everytime it boots normal.....But, there is still a problem... baseband version is Unknown and there is no IMEI Number.

Larry2999 said:
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Click to expand...
Click to collapse
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.

mtsosie said:
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
Click to expand...
Click to collapse
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456

Larry2999 said:
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Click to expand...
Click to collapse
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.

mtsosie said:
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
Click to expand...
Click to collapse
You are most welcome. Glad to know it's now working.

hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open

dark_darkness said:
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
Click to expand...
Click to collapse
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486

can u share a link?
Larry2999 said:
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
Click to expand...
Click to collapse
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?

dark_darkness said:
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
Click to expand...
Click to collapse
I suggested custom recovery and not custom ROM. The idea is to get your phone back in working order first. Flashing a complete stock restore image should do it. Please refer to the thread I forwarded earlier. You should be able to flash custom recovery (like CWM or TWRP) to your phone via Odin and then use the custom recovery to flash the stock restore image.

need help badly! did i brick my phone?

need help
hello, i just downloaded the latest firmware NK2 link from the general thread, and run it thru Odin, and i unzip it. and Odin says PASS, but when turned it on my phone only stuck at the T-Mobile 4G LTE. whats wrong? what i need to do? help pls. thanks.
edit: i re do the odin, and now i got failed right away! now i cannot do the odin anymore. it gets failed right away. did i brick my phone? also if i turned it on it says
odin mode
product name : sgh-m919
current binary: samsung official
system status: custom
knox kernel lock: 0x0
knox warranty void: 0x0
csb-config-lsb: 0x30
write protection: enabl
eMMc: burst mode enabled
and it has a picture of phone yellow triangle with asterisk inside and computer
firmware upgrade encountered an issue. please select recovery mode in kies and try again.
pls help.

caloyzki said:
need help
hello, i just downloaded the latest firmware NK2 link from the general thread, and run it thru Odin, and i unzip it. and Odin says PASS, but when turned it on my phone only stuck at the T-Mobile 4G LTE. whats wrong? what i need to do? help pls. thanks.
edit: i re do the odin, and now i got failed right away! now i cannot do the odin anymore. it gets failed right away. did i brick my phone? also if i turned it on it says
odin mode
product name : sgh-m919
current binary: samsung official
system status: custom
knox kernel lock: 0x0
knox warranty void: 0x0
csb-config-lsb: 0x30
write protection: enabl
eMMc: burst mode enabled
and it has a picture of phone yellow triangle with asterisk inside and computer
firmware upgrade encountered an issue. please select recovery mode in kies and try again.
pls help.
Click to expand...
Click to collapse
update
after installing the firnware NK2, via odin, now im stuck at tmobile 4g lte logo. and i cant even access to my recovery to do wipe. pls help.

What happens when you try to access recovery?

caloyzki said:
update
after installing the firnware NK2, via odin, now im stuck at tmobile 4g lte logo. and i cant even access to my recovery to do wipe. pls help.
Click to expand...
Click to collapse
flash the root tar via odin somewhere in this forum or even on chainfires website. and then try rebooting. if not flash a custom recovery tar like philz and than i guarantee you will be able to boot into recovery and wipe your cache/ or flash a new rom

[Q] ODIN Fail on Unroot and Restore Stock Attempt

I am trying to unroot and restore stock ROM so that I can sell my Note 2014 10.1.
I am using ODIN 3.09 and P600UEUCNK1_P600XARCNK1_HOME.tar.md5
ODIN keeps giving me a FAIL. Looks like "Cant Open Serial Port". I have attached a screen shot from ODIN.
Any ideas as to what I can do here?
Thanks

You need to extract the zip file, and edit .md5 off the end, leaving a .tar file to flash. Make sure you unroot via superuser, then factory reset, then download mode.....Will take 7-9 minutes. Wait for reboot, and removed to show in ODIN. Just did this myself, and device shows official, and recovery is stock, without even the Knox splash showing recovery bit! Easy breezy. I flashed on top of 4.4.4 bootloader the 4.4.2 .tar, and let it update OTA. T-Mobile P607-T Gluck!

Worked like a charm my friend...Thanks so much
Sent from my SM-N900P using Tapatalk

I followed these steps. Flashed same tar file, and successful install. Although i cant update software because says my version has been modified. Anyway to still get updates and be totally stock?

Flash updates from Kies instead OTA is never going to work again.
Sent from my SM-P600 using XDA Free mobile app

Please could anyone had the steps ... the same issue is faced with Note 10.1 Gt-8000
I' m using N8000XXUDNF2_N8000OJVDNF3_N8000XXUDNF1_HOME.tar with ODIN 3.07 which is detecting the com 3 or com 6 with it, and failing always and the device is stopped at either ODIN MODE if I used the volume down plus power or at Firmware upgrade encountered an issue. please select recovery mode in kies and try again... it would never enter to the recovery mode or Bootloader, please advise... thanks in advanced.

Cant install TWRP after CF auto root bootloops phone, HELP.

I had 4.4.4 and flashed cf-auto-root trltrespr-smn910p. It said successful and auto rebooted into a bootloop. I tried downloading the twrp-2.8.7.0-trltespr.img.tar with odin3_v3.10.6 and no twrp. I unchecked autoboot, un plugged usb, battery for 10 seconds still nothing. Another problem is i lost the screenshot of the device info. Ive searched and triedwhat i could find but im at my whits end.

Try the NK2 stock tar. Backup internal sdcard (if you can) and wipe everything but extsdcard.
What you describe sounds like your bootloader is one of those that can't be downgraded. Have you ever been on Lollipop? {If so, you won't succeed getting it back to KitKat unless it never updated past OB7. In that case, you would have to Odin or KIES update to stock OG5. And root would only possible with kernel exploit on Beastmode kernel.}
Sent from my SM-N910P using Tapatalk

Ugh, Ok I downloaded the firmware file OG5 from sam mobile and it fails? Ive tried
N910PVPU4COG5_N910PSPT4COG5_N910PVPU4COG5_HOME.tar.md5
N910PVPU1ANK2_N910PSPT1ANK2_N910PVPU1ANK2_HOME.tar.md5
twrp-2.8.7.0-trltespr.img.tar
I just moved and Im using a 3g connection in the evenings until we can find an internet company that works out in the country so this is really frustrating.
Im lost on what to try next? Any other suggestions???

A week has past; are you restoring a nandroid from TWRP recovery and booting that?
If so, what is your bootloader? Use galaxy tools or save your TWRP log to sdcard and read it; the bootloader is near the bottom.
Reasons for OG5 tar failing could be that the tar wasn't extracted or you don't have a stock kernel installed. Try that or describe your current setup regarding bootloader and kernel.
Have you tried to update through KIES?
What Odin or KIES failures are you getting?
Sent from my SM-N910P using Tapatalk

Sorry, I have 3 other company phones so Ive been using one of those. We just moved ourselves and my irrigation and landscape company, still no home internet. Life is tough right now between work and 3 kids with all their activites. I had responded but I see it didn't go through so if you will let me start again and maybe we can get this brick working.
I use odin3 v3.10.6. Ive tried to use the cfauto flash and it will not stick. Ive tried to download the stock tars above and they don't work. I cant get to a custom boot with everything Ive tried. I cant find more than the above tars to download to the phone. When I go into download mode the phone says
Odin mode (high speed)
product name:sm-n910p
current binary: Custom
System Status: official
Reactivation lock: off
knox warranty void: 0x1 (4)
qualcom secureboot: enable (csb)
rp swrev: s1, t3, r1, a4, p1
secure download : enable
udc start
so what should I try now? Im begging for mercy on this thing...
And I don't get fails, Odin says all threads succeeded 1 / 0 fail

Not sure I follow without a text of Odin and version you're flashing.
Had a guy in the forum last week that could get Odin to flash but phone kept boot looping and TWRP wouldn't flash a zip. Finally flashed CWM but still looped. I believe what he finally did was Odin flash stock tar with no auto reboot, factory reset in recovery (may have been Philz CWM), flashed Odin stock tar with auto reboot enabled. Pull battery for thirty seconds prior to stock tar flash.
Sent from my SM-N910P using Tapatalk

Note 2 N7105 doesn't reboot after flashing to stock 4.4.2

Dear all,
I just have a serious problem with my Note 2 N7105. I bought this phone with a rooted 4.3 androit and everything worked fine beside using the automatic update function (over the air update of android).
Therefore I downloaded the german 4.4.2 from Sammobile and flashed it with odin.
sammobile.com/firmwares/download/32565/N7105XXUFNE3_N7105DBTFNE1_DBT
Odin flashed completely with any errors . -> All threads completed. (succeeded: 1 / fail: 0)
But unfortunately it is not rebooting to androit nor reboot into recovery mode. After turning on the phone, I can see the samsung logo and after that it tried to boot and a red exclamation mark pops up and it's restarting again. The only possible thing is to get into the download mode again.
I also downloaded the german 4.3 version from sammobile and flased it with odin - but results stay the same.
I would be very happy about any help. Sorry in advance for my unprofessional explanation.

make sure you have downloaded the right tar file for your samsung

Anilkumar12345 said:
make sure you have downloaded the right tar file for your samsung
Click to expand...
Click to collapse
Could fix it meanwhile - it wasn't a problem of the tar file - the tar file was correct - but whyever the recovery was broken after downloading and installing the cwm recovery I was able to get into the recovery mode again and afterwards also successfully install the stock 4.4.2 tar file from sammobile.
Cheers,
mr_moods