Related
I was trying to go to 4.3 stock using a 4.1.1 md5 stock via mobile odin
Then when I put to install update from external storage "update412.zip" (4.2 I think) it was updating and stuff then the phone just turned off!
I was suppose to do 413 too but it never went past 412 (413=4.3)
Now the phone wont even light up when i press the power button, but it shows it trying to connect to PC with my cable but obviously cant recognize it... Help meeeee!
ibroza said:
I was trying to go to 4.3 stock using a 4.1.1 md5 stock via mobile odin
Then when I put to install update from external storage "update412.zip" (4.2 I think) it was updating and stuff then the phone just turned off!
I was suppose to do 413 too but it never went past 412 (413=4.3)
Now the phone wont even light up when i press the power button, but it shows it trying to connect to PC with my cable but obviously cant recognize it... Help meeeee!
Click to expand...
Click to collapse
Sorry but the problem is not quite clear. Were you trying to flash 4.1.1 via Mobile Odin when you were already on 4.3? What you are describing sounds like a hard brick but it's hard to understand how Mobile Odin would have caused this since it doesn't attempt to mess with your bootloader partition. Please provide more info including your phone model and Android version you were on prior to the brick. If you had the AT&T version, the thread below may help you ...
http://forum.xda-developers.com/showthread.php?t=2549068
I recently installed miui from official website for lg e975. My phone is lg f180 so they both are same.
It was working fine till this morning it asked for update. I allowed. It retarted and now it starts shows google logo. Then goes to recovery.
I flashed my original backup rom. Then even flashed miui rom. Nothing changes. I wiped cache. Data dalvik a lot of times.
It just starts shows google logo. Goes to recovery. Please help
Im sorry if this thread doeant belong here. Mods please move
Thought i should add.
I dont have any other access but cwm recovery
I only have a backup of my original rom through cwm. No kdz files.
I have a miui zip rom on phone as well
awais3344 said:
Thought i should add.
I dont have any other access but cwm recovery
I only have a backup of my original rom through cwm. No kdz files.
I have a miui zip rom on phone as well
Click to expand...
Click to collapse
Flash stock zip kernel from artmod thread.
the problem is. I can't upload any files to mobile phone. if i connect to pc, it turns on, goes to recovery, so I click on mount storage, and other mount option, nothing happens. My computer detects phone as F180L with a exclamation mark.
If i go to download mode, and then try to flash any KDZ file from all the f180 KDzs. It gives me errors.
LG Support Tool on entering serial number and model name says "check out serial number and model"
ADB never detects my phone. So I can't upload anything.
No option to upload files via SD Card.
ok, so I have no clue what happened :crying: phone was in download mode. I did nothing, but only installed LG Support Tool USB driver, while the mobile connected.
Then I installed Microsoft .net framework 4.0. And my phone is now qhs_usbdload. it's officially bricked now. I have no clue what happened. This is all that happened before I restarted and selected "reboot to bootloader" and its dead. So there's nothing left to do but throw it out
WTF OKAY! I have no clue!
But, after seeing that qhs usbdload. (i have seen that before with other phones). I complete lost any hope.
So I for feeling contended, downloaded qpst, and emmc software download, and selected MPRG8064.hex and msimage.bin.
Then like I expected it threw an error "image download failed, cookie if present not received"
so I lost hope disconnected my phone and put it there. After a few minutes thought I should try one last time.
so I connect it my pc and VIOLA it turns ON!?
now I have that same rebooting to recovery problem. I have no explanation for whatever has happened to phone in past 3 hours. I have been with phones for years. This is the weirdest thing to happen ever :angel:
Now someone, please help me?
1. Why is this in Development section?
2. You can't mount internal SD as USB storage. Use adb push or adb sideload instead, that will help you to get the files onto your phone.
awais3344 said:
WTF OKAY! I have no clue!
But, after seeing that qhs usbdload. (i have seen that before with other phones). I complete lost any hope.
So I for feeling contended, downloaded qpst, and emmc software download, and selected MPRG8064.hex and msimage.bin.
Then like I expected it threw an error "image download failed, cookie if present not received"
so I lost hope disconnected my phone and put it there. After a few minutes thought I should try one last time.
so I connect it my pc and VIOLA it turns ON!?
now I have that same rebooting to recovery problem. I have no explanation for whatever has happened to phone in past 3 hours. I have been with phones for years. This is the weirdest thing to happen ever :angel:
Now someone, please help me?
Click to expand...
Click to collapse
Some user got that problem before. I am not sure about how they solve it but I guess that they flash their original KDZ back. If your phone can enter download mode, you should try LG Flash tool 2014 and flash your original kdz to restore incorrect system image.
About adb cannot find your phone, try to remove adb driver from device manager and reinstall LG usb driver.
artit said:
Some user got that problem before. I am not sure about how they solve it but I guess that they flash their original KDZ back. If your phone can enter download mode, you should try LG Flash tool 2014 and flash your original kdz to restore incorrect system image.
About adb cannot find your phone, try to remove adb driver from device manager and reinstall LG usb driver.
Click to expand...
Click to collapse
My phone is acting weird. Sometime it would start. Sometime the red light would blink. Sometimes the red light wouldn't blink at all. Then sometimes, it starts. And then it doesn't.
I have no clue what is going on with it.
But it went to download mode many times again, it would go to fastboot, bootloader, recovery etc. Then sometimes it will not respond to any buttons at all! I know its battery is down, but idk if it's charging or not?
I don't know how to know whether the phone is charging or not. I left it charging for 30 minute, and it didn't even buzz. :crying:
awais3344 said:
I know its battery is down, but idk if it's charging or not?
I don't know how to know whether the phone is charging or not. I left it charging for 30 minute, and it didn't even buzz. :crying:
Click to expand...
Click to collapse
One thing you can do (I've done it in the past a couple of times) is to crack your phone open, disconnect the battery, and charge it with an external charger. That would at least give you a full battery to start with...
Regarding the charging problems, I had that once. I was able to startup the phone by simply using a 2A charger instead of the LG's 1.2A.
When I had this issue it was charging while in recovery. Please look at this post and flash your kdz.
http://forum.xda-developers.com/showthread.php?p=54934779. This one helped me http://forum.xda-developers.com/showthread.php?p=53728658
Sent from my LG-E975 using XDA Free mobile app
kt-Froggy said:
One thing you can do (I've done it in the past a couple of times) is to crack your phone open, disconnect the battery, and charge it with an external charger. That would at least give you a full battery to start with...
Click to expand...
Click to collapse
thanks. but after charging it. I couldn't turn the screen off because it goes in recovery. I turned off the phone after good 30 minute charging. Then went to sleep. And in the morning I connected it to pc. by holding volume buttons for download mode. It didn't go to download mode. Only it's red light is blinking. and no display.
awais3344 said:
thanks. but after charging it. I couldn't turn the screen off because it goes in recovery. I turned off the phone after good 30 minute charging. Then went to sleep. And in the morning I connected it to pc. by holding volume buttons for download mode. It didn't go to download mode. Only it's red light is blinking. and no display.
Click to expand...
Click to collapse
Hey man. I have exaxt same prolem when update miui. Just do this when you got your recovey. Connect your phone to pc, let your pc update driver. Use adb sideload to flash stock zip kitkat e975 lgviet. Goodluck.
huy_gm said:
Hey man. I have exaxt same prolem when update miui. Just do this when you got your recovey. Connect your phone to pc, let your pc update driver. Use adb sideload to flash stock zip kitkat e975 lgviet. Goodluck.
Click to expand...
Click to collapse
Hi, regarding that. I was able to sideload exitrecovery.zip file. It goes to 100% then nothing happens. Nothing happened on phone screen as well.
And can you send me link to that stock zip kitkat? i have a miui.zip and few other roms that I have not tried. thanks
Edit: also what should I do about adb, am i doing correct?
Becuase in adb devices, my device is displayed with deviceID sideload
And i have only pasted adb folder, with a dll and a zip file, there is nothing else, do I need to install SDK?
I tried lg flash tool 2014 again, and it flashed, I swear yesterday I tried to flash it, and after clicking on it, it never showed me country and language selection menu, so it would sit there and do nothing. now I don't know how but it did it :laugh:
thank you so much you'all
please help me!! clearly i am more of a noob than I thought I was!
I rooted my phone using Odin a few months ago. Then it just crapped out on me. Now it is stuck in a boot loop mode. I can get it to recovery mood and download mode. I have tried wiping the cache partition and done the factory rest. That isn't the issue. The issue is that when I have Odin open the phone isn't being recognized. it keeps saying "USB device not recognized. the last USB device you connected to this computer malfunctioned, and Windows does not recognize it". I have tried reinstalling the drivers for my Sprint S6. I have also updated the media package for my windows 8.1. But it still isn't recognizing the phone. I also tried un instaling and reinstalling. I have smart switch but still nothing. I am not entirely sure how to fix this. Please Help!! Also, in the top left hand corner where it says "kernal is not seandriod enforcing. custom binary blocked by frp lock"
I've exhausted everything best to my knowledge. I appreciate all the help I can get from you experts. Thank all in advance from this tech noob!
Gladi80rPrincess09 said:
please help me!! clearly i am more of a noob than I thought I was!
...
I've exhausted everything best to my knowledge. I appreciate all the help I can get from you experts. Thank all in advance from this tech noob!
Click to expand...
Click to collapse
Geez... that sucks, and disappointing no one has replied yet.
I hate to reply with a few of the obvious tricks- but it has happened multiple times to me that my phone won't be recognized by ODIN (or anything other than as "charging"). Usually this is solved by switching to other USB ports, and plugging-unplugging a few times, but when that fails (which it does not infrequently)- I have gotten lucky by not just restarting my computer, but actually turning it off, waiting a moment and turning it back on.
Magically sometimes that does it.
Hope that works for you, and that others more senior weigh in on this :good:
I second what spammy said.
I just spent 6 hours fixing my Sprint s6. I got it domestic unlocked and somehow near-bricked it, and then got the dreaded usb not recognized message. Shutting my laptop all the way down and letting it sit a few minutes did the trick and I was able to use Odin afterwards.
update!!
so, i got it to connect by just lifting the tongue a little. It connected to Odin. I tried to flash it using the TAR file but it keeps saying failed. Can anyone tell me why it says "custom binary blocked by frp lock" and how to fix that ? I know I have to connect it to samsung online or something but the phone is stuck in boot loop mode so I cant really do much. Like I said before I tried to flash with the 5.0.2 TAR file and ended up with the following message at the top left and corner in red and black highlight "SW REV. CHECK FAIL. DEVICE: 2. BINARY: 1" what does this mean? is there a fix? and how do I fix it? my phone is already factory rest and I lost everything so I am not concerned about that as long as I can get it to turn back on. Please help me.
update
chatovishious said:
I second what spammy said.
I just spent 6 hours fixing my Sprint s6. I got it domestic unlocked and somehow near-bricked it, and then got the dreaded usb not recognized message. Shutting my laptop all the way down and letting it sit a few minutes did the trick and I was able to use Odin afterwards.
Click to expand...
Click to collapse
spammy l said:
Geez... that sucks, and disappointing no one has replied yet.
I hate to reply with a few of the obvious tricks- but it has happened multiple times to me that my phone won't be recognized by ODIN (or anything other than as "charging"). Usually this is solved by switching to other USB ports, and plugging-unplugging a few times, but when that fails (which it does not infrequently)- I have gotten lucky by not just restarting my computer, but actually turning it off, waiting a moment and turning it back on.
Magically sometimes that does it.
Hope that works for you, and that others more senior weigh in on this :good:
Click to expand...
Click to collapse
so, i got it to connect by just lifting the tongue a little. It connected to Odin. I tried to flash it using the TAR file but it keeps saying failed. Can anyone tell me why it says "custom binary blocked by frp lock" and how to fix that ? I know I have to connect it to samsung online or something but the phone is stuck in boot loop mode so I cant really do much. Like I said before I tried to flash with the 5.0.2 TAR file and ended up with the following message at the top left and corner in red and black highlight "SW REV. CHECK FAIL. DEVICE: 2. BINARY: 1" what does this mean? is there a fix? and how do I fix it? my phone is already factory rest and I lost everything so I am not concerned about that as long as I can get it to turn back on. Please help me.
Gladi80rPrincess09 said:
so, i got it to connect by just lifting the tongue a little. It connected to Odin. I tried to flash it using the TAR file but it keeps saying failed. Can anyone tell me why it says "custom binary blocked by frp lock" and how to fix that ? I know I have to connect it to samsung online or something but the phone is stuck in boot loop mode so I cant really do much. Like I said before I tried to flash with the 5.0.2 TAR file and ended up with the following message at the top left and corner in red and black highlight "SW REV. CHECK FAIL. DEVICE: 2. BINARY: 1" what does this mean? is there a fix? and how do I fix it? my phone is already factory rest and I lost everything so I am not concerned about that as long as I can get it to turn back on. Please help me.
Click to expand...
Click to collapse
Where you previously on 5.1.1? If so I hear downgrading causes problems. Download a more recent tar.
Mine is 5.1.1 OL1 modem.
I'm betting that is your problem.
help me!
chatovishious said:
Where you previously on 5.1.1? If so I hear downgrading causes problems. Download a more recent tar.
Mine is 5.1.1 OL1 modem.
I'm betting that is your problem.
Click to expand...
Click to collapse
i can't remember if my phone is upgraded or not. i did it with 5.0.2 and ive been on the search for the 5.1.1 file. where can I find it?
Gladi80rPrincess09 said:
i can't remember if my phone is upgraded or not. i did it with 5.0.2 and ive been on the search for the 5.1.1 file. where can I find it?
Click to expand...
Click to collapse
Sounds like your USB is a bit out of wack. You need to make sure that the PC you are using is finding the device properly, loading the drivers, and allowing you to access the internal storage. Just go to "My Computer" on your PC and your device should show up and allow you to access it. Otherwise trying to use Odin will be a waste of your time.
Once you have that Odin should find it no problem. However, if your microUSB on the device is acting intermittent and you start flashing in Odin and it disconnects for a sec there will be issues. You don't want an interrupt during the flash.
If you can do all this go to this link and download Odin 3.10.6 and the OJ7 tar file: http://forum.xda-developers.com/sprint-galaxy-s6/general/how-to-to-100-stock-root-t3075448
Don't use previous version of Odin as they are confirmed to have issues flashing some tar files on the S6. If it doesn't work try doing another factory reset through stock recovery and try again.
Report back your findings to continue troubleshooting if needed.
Thank you! progress/update
CCallahan said:
Sounds like your USB is a bit out of wack. You need to make sure that the PC you are using is finding the device properly, loading the drivers, and allowing you to access the internal storage. Just go to "My Computer" on your PC and your device should show up and allow you to access it. Otherwise trying to use Odin will be a waste of your time.
Once you have that Odin should find it no problem. However, if your microUSB on the device is acting intermittent and you start flashing in Odin and it disconnects for a sec there will be issues. You don't want an interrupt during the flash.
If you can do all this go to this link and download Odin 3.10.6 and the OJ7 tar file: http://forum.xda-developers.com/sprint-galaxy-s6/general/how-to-to-100-stock-root-t3075448
Don't use previous version of Odin as they are confirmed to have issues flashing some tar files on the S6. If it doesn't work try doing another factory reset through stock recovery and try again.
Report back your findings to continue troubleshooting if needed.
Click to expand...
Click to collapse
so, i downloaded the 5.1.1 Tar file progress is that I am going to flash it. I have been using the most updated version of Odin (3.10.7) could that be causing the issue? the phone stays connected while its flashing in Odin. Once it is connected I dont mess with it? Also, please answer me if I am able to fix this issue and will i be able to get my phone booted?
Gladi80rPrincess09 said:
so, i downloaded the 5.1.1 Tar file progress is that I am going to flash it. I have been using the most updated version of Odin (3.10.7) could that be causing the issue? the phone stays connected while its flashing in Odin. Once it is connected I dont mess with it? Also, please answer me if I am able to fix this issue and will i be able to get my phone booted?
Click to expand...
Click to collapse
I have not used the 3.10.7 version yet but should not be a problem.
Download the tar file, connect the device and make sure Odin shows the device as connected/ready, hit the AP button and select your tar file, then flash and let finish. Then it will reboot automatically and boot up normally.
Try this and post your findings.
question
CCallahan said:
Sounds like your USB is a bit out of wack. You need to make sure that the PC you are using is finding the device properly, loading the drivers, and allowing you to access the internal storage. Just go to "My Computer" on your PC and your device should show up and allow you to access it. Otherwise trying to use Odin will be a waste of your time.
Once you have that Odin should find it no problem. However, if your microUSB on the device is acting intermittent and you start flashing in Odin and it disconnects for a sec there will be issues. You don't want an interrupt during the flash.
If you can do all this go to this link and download Odin 3.10.6 and the OJ7 tar file: http://forum.xda-developers.com/sprint-galaxy-s6/general/how-to-to-100-stock-root-t3075448
Don't use previous version of Odin as they are confirmed to have issues flashing some tar files on the S6. If it doesn't work try doing another factory reset through stock recovery and try again.
Report back your findings to continue troubleshooting if needed.
Click to expand...
Click to collapse
CCallahan said:
I have not used the 3.10.7 version yet but should not be a problem.
Download the tar file, connect the device and make sure Odin shows the device as connected/ready, hit the AP button and select your tar file, then flash and let finish. Then it will reboot automatically and boot up normally.
Try this and post your findings.
Click to expand...
Click to collapse
i knocked the phone off the computer desk and it disconnected from Odin while it was in progress and it said failed. The phone was in download mode and now it is stuck on a blue screen that has white triangle with exclamation point. it reads "an error has occurred while updating the device software. use the emrgency recovery function in the smart swtch pc software" what did I do?
Gladi80rPrincess09 said:
i knocked the phone off the computer desk and it disconnected from Odin while it was in progress and it said failed. The phone was in download mode and now it is stuck on a blue screen that has white triangle with exclamation point. it reads "an error has occurred while updating the device software. use the emrgency recovery function in the smart swtch pc software" what did I do?
Click to expand...
Click to collapse
Can you get the device back in download mode?
update!!
CCallahan said:
Can you get the device back in download mode?
Sent from my SM-G920P using Tapatalk
---------- Post added at 10:59 AM ---------- Previous post was at 10:54 AM ----------
Can you get the device back in download mode?
Sent from my SM-G920P using Tapatalk
Click to expand...
Click to collapse
yes, i got it back to download mode. i tried to reflash it with Odin and now it says failed. i can't turn it on or off. if i try to boot it off then it goes to that blue screen again i tried to do the smart switch thing but it doesnt recognize my device
Gladi80rPrincess09 said:
yes, i got it back to download mode. i tried to reflash it with Odin and now it says failed. i can't turn it on or off. if i try to boot it off then it goes to that blue screen again i tried to do the smart switch thing but it doesnt recognize my device
Click to expand...
Click to collapse
Dont worry about that. That's what happened to me, but that screen functions the same as Download mode. you can still flash tar files from there.
Here was the link to the tar files I used.
http://www.droidviews.com/install-latest-ol1-stock-firmware-on-sprint-galaxy-s6-and-s6-edge/
thank you for the help!!
chatovishious said:
Dont worry about that. That's what happened to me, but that screen functions the same as Download mode. you can still flash tar files from there.
Here was the link to the tar files I used.
http://www.droidviews.com/install-latest-ol1-stock-firmware-on-sprint-galaxy-s6-and-s6-edge/
Click to expand...
Click to collapse
i got it to work!!!
Gladi80rPrincess09 said:
please help me!! clearly i am more of a noob than I thought I was!
I rooted my phone using Odin a few months ago. Then it just crapped out on me. Now it is stuck in a boot loop mode. I can get it to recovery mood and download mode. I have tried wiping the cache partition and done the factory rest. That isn't the issue. The issue is that when I have Odin open the phone isn't being recognized. it keeps saying "USB device not recognized. the last USB device you connected to this computer malfunctioned, and Windows does not recognize it". I have tried reinstalling the drivers for my Sprint S6. I have also updated the media package for my windows 8.1. But it still isn't recognizing the phone. I also tried un instaling and reinstalling. I have smart switch but still nothing. I am not entirely sure how to fix this. Please Help!! Also, in the top left hand corner where it says "kernal is not seandriod enforcing. custom binary blocked by frp lock"
I've exhausted everything best to my knowledge. I appreciate all the help I can get from you experts. Thank all in advance from this tech noob!
Click to expand...
Click to collapse
Hey! Still stuck?
Poebat said:
Hey! Still stuck?
Click to expand...
Click to collapse
No according to the post above yours.
koop1955 said:
No according to the post above yours.
Click to expand...
Click to collapse
K. Sometimes something appears to work and then fails :/ happens sometimes
Thank you all for the kelp! i finally got it to work. Never again will I root my phone. Now, the only sad thing about it is that I lost all my treasured memories ( pictures and videos)
Gladi80rPrincess09 said:
Thank you all for the kelp! i finally got it to work. Never again will I root my phone. Now, the only sad thing about it is that I lost all my treasured memories ( pictures and videos)
Click to expand...
Click to collapse
nothing wrong with rooting if you know what you're doing. ?
Sent from my SM-G900P using Tapatalk
Sorry If this is covered somewhere else but I've tried a number of search queries and haven't found anything.
My issue is that I have a rooted verizon LGG4 that has started acting up quite a bit. I would like to flash back to a stock kdz but because of the glitches with the current software my PC will not recognize the phone. I have used different usb cords and even had the port itself checked out and the tech said there was nothing wrong with it that he could tell. So I believe the issue is with the software. Is there anyway to flash the phone back with out a PC?
Thanks
Fracjunky said:
Sorry If this is covered somewhere else but I've tried a number of search queries and haven't found anything.
My issue is that I have a rooted verizon LGG4 that has started acting up quite a bit. I would like to flash back to a stock kdz but because of the glitches with the current software my PC will not recognize the phone. I have used different usb cords and even had the port itself checked out and the tech said there was nothing wrong with it that he could tell. So I believe the issue is with the software. Is there anyway to flash the phone back with out a PC?
Thanks
Click to expand...
Click to collapse
KDZ you need pc.. maybe format or try another PC.
I have tried 2 different PC's. None of them work with this phone but all work with another G4 no problem. I do have access to img and bin files but I'm still not sure how I could use them as all I have ever used to flash is LGUP on my PC and the C promt. If i could just figure out something to fix the USB issue I'd have it made otherwise I need to figure out a way to flash from the phone itself.
Have you tried lgup it is good for these types of issues.....
When I had issues I found that with lgup he best way is leave your device plugged in and pull the battery out and problem solved.....
9
Fracjunky said:
Sorry If this is covered somewhere else but I've tried a number of search queries and haven't found anything.
My issue is that I have a rooted verizon LGG4 that has started acting up quite a bit. I would like to flash back to a stock kdz but because of the glitches with the current software my PC will not recognize the phone. I have used different usb cords and even had the port itself checked out and the tech said there was nothing wrong with it that he could tell. So I believe the issue is with the software. Is there anyway to flash the phone back with out a PC?
Thanks
Click to expand...
Click to collapse
Does ure pc reconize device at all. Whats it say in device manager.
Have u checked your drivers?
I use the old lgflash tool from lg g2. Also works great for messed up situations.
Also have you tried booting in download mode to see if its reconized. Bad firmware shouldnt affect dl mode connections
LGUp is actually the program I prefer to use and it can't find my device any longer.
The PC will charge the phone and that's it. Current drivers and all but still says unrecognized device in the device manager. I have a couple of g4s that work just fine I might just start overwriting system files with working ones from the other devices until I figure out which one is corrupted.
Fracjunky said:
LGUp is actually the program I prefer to use and it can't find my device any longer.
The PC will charge the phone and that's it. Current drivers and all but still says unrecognized device in the device manager. I have a couple of g4s that work just fine I might just start overwriting system files with working ones from the other devices until I figure out which one is corrupted.
Click to expand...
Click to collapse
Try FlashFire from playstore. It can flash from within android. Never used it though..
And sorry to ask this but have you tried to change the connection mode (swipe down and change to ptp)?
.
Sent from my LG-H815 using XDA Labs
I tried and the error is: "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software".
The phone don't entry in mode recovery and the download mode, I tried many times...
The software (Smart Switch PC) does not recognize the phone.
Can anybody help me!
juninromualdo said:
I tried and the error is: "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software".
The phone don't entry in mode recovery and the download mode, I tried many times...
The software (Smart Switch PC) does not recognize the phone.
Can anybody help me!
Click to expand...
Click to collapse
THis happend to me a while back and it is easy to fix. All you have to do is close Odin. Then restart odin and load the correct files into each of the slots - then plug your phone into the USB/PC - you should see the phone connect in Odin - then just click start and run ODIN to update the files you added to the slots in odin.
When you get that error message, the phone is technically still in download mode and odin will still recognize the phone and allow you to update using the files for your phone. Be sure you are using the correct firmware - be sure you add each of the files into the appropriate slot.
Good Luck.
Geekser said:
THis happend to me a while back and it is easy to fix. All you have to do is close Odin. Then restart odin and load the correct files into each of the slots - then plug your phone into the USB/PC - you should see the phone connect in Odin - then just click start and run ODIN to update the files you added to the slots in odin.
When you get that error message, the phone is technically still in download mode and odin will still recognize the phone and allow you to update using the files for your phone. Be sure you are using the correct firmware - be sure you add each of the files into the appropriate slot.
Good Luck.
Click to expand...
Click to collapse
The ondin do not recognize :crying::crying::crying: but I can try, thanks
What version of Odin are you using? What version N10+ do you have? Where did you get the firmware from? I have seen downloads that were corrupt and needed to be redownloaded. Make sure when you extract it it’s the right firmware for your phone as well. Report back and I’m sure we can help you. These phones are tough to brick.
Sent from my iPad using Tapatalk
italbomber said:
What version of Odin are you using? What version N10+ do you have? Where did you get the firmware from? I have seen downloads that were corrupt and needed to be redownloaded. Make sure when you extract it it’s the right firmware for your phone as well. Report back and I’m sure we can help you. These phones are tough to brick.
Click to expand...
Click to collapse
Thank you, but I took earlier today at Samsung, there they solved the problem and even changed the battery. The biggest problem is that I wasn't entering the download screen anymore, I don't know what magic they did ...
Adm close the topic okay, Thank you
Geekser said:
THis happend to me a while back and it is easy to fix. All you have to do is close Odin. Then restart odin and load the correct files into each of the slots - then plug your phone into the USB/PC - you should see the phone connect in Odin - then just click start and run ODIN to update the files you added to the slots in odin.
When you get that error message, the phone is technically still in download mode and odin will still recognize the phone and allow you to update using the files for your phone. Be sure you are using the correct firmware - be sure you add each of the files into the appropriate slot.
Good Luck.
Click to expand...
Click to collapse
THANKS SO MUCH! Simple but everything I needed to know! I had no idea I was still IN download mode!
juninromualdo said:
Adm close the topic okay, Thank you
Click to expand...
Click to collapse
sometimes it is best to just leave the topic and post going - other people might have a similar problem - read the post - see what others have said and find that they can fix their phone. In the post right after the one you said to ask Admin to close the thread, someone else posted a thank you because they discovered they could fix their phone. Proof that sometimes it is best to just let it go - if no one reads it - it will fade out all on it's own. Just a thought.
Geekser said:
THis happend to me a while back and it is easy to fix. All you have to do is close Odin. Then restart odin and load the correct files into each of the slots - then plug your phone into the USB/PC - you should see the phone connect in Odin - then just click start and run ODIN to update the files you added to the slots in odin.
When you get that error message, the phone is technically still in download mode and odin will still recognize the phone and allow you to update using the files for your phone. Be sure you are using the correct firmware - be sure you add each of the files into the appropriate slot.
Good Luck.
Click to expand...
Click to collapse
YOU ROCK!!!! Thanks a Bunch!!!!