Have a bit of a problem here. I gave my parents my SGS3 and i know i had a root on it and was running stock. Im pretty sure that before giving it to them i ran an OTA lost root then re rooted. This most recent OTA has left the phone in a boot loop. Since it has been so long i have no idea what version it was running. Ive done some reading here and thought the solution would be to go back to 4.1.1 but i few posts warned that it could hard brick the phone if it was upgraded to 4.3... Anyway to tell what i have on there. I can get to download mode. Unable to get recovery open. ...Any help would be helpful. Thank you
Boot into download mode. Do you see anything on the screen about warranty bit?
Yes set to 1 now... it was zero earlier before I tried to fix my issues via kies.
Now I don't get boot loop any more but it just asks to be hooked back to kies to fix issue which it doesn't
Sent from my SAMSUNG-SGH-I337 using XDA
You tried to fix/update with kies? Are you getting an error message about a firmware problem?
The fact that you have a line in download mode about warranty means you have at least a 4.3 bootloader; therefore, you cannot flash back to 4.1.1.
I suggest you flash Philz Touch for the d2lte and flash CM11 to at least get your phone booted so you can confirm the bootloader and modem on your phone.
Yes I tried kies... It starts to download it but then fails and does not give me an "emergency recovery code" so i can not continue.
when turning on the phone no it loads up a screen that shows the ODIN info at the top like in download mode but in the center of the screen it says " Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again." Of course no luck there.
Ok so i at least have 4.3 bootloader... one check off the list...thank you
I will flash Philz touch and then CM11 ... I should be able to use ODIN ?
Going to use Philz touch philz_touch_6.48.4-d2lte.zip ...
Use Odin 3.07 to flash Philz Touch but make sure you download and flash the tar.md5 version, not the zip version.
I had 3.09 and got philz on .... trying to find a usable CM11 I have Att as my carrier.. was going to use one of the stable releases cm-10.2.1-d2att.zip ... used a micro sd to load on the rom ... but after i attempted to install the i got installation aborted ( Status 7)
http://download.cyanogenmod.org/?device=d2lte
"all I can really do, is stay out of my own way and let the will of heaven be done"
Ok so i got cm-11-20141209-NIGHTLY-d2lte.zip loaded.....
I would like to get this back to stock as or as close as possible ( touchwiz and all) this was my mothers phone 60+ years old ...she doesnt like change
thanks for the help so far what info do we need
Android version 4.4.4
Baseband I747UCUFNJ1
Kernel
3.4.104-cyanogenmod-g38a4e52
[email protected] #1
dont know if this one youre looking for but this should take you to stock 4.4.2. (read read read - have a backup - go slow and ask questions if not sure).
http://forum.xda-developers.com/showthread.php?t=2788357
"all I can really do, is stay out of my own way and let the will of heaven be done"
Thank you ... i will probaly need to down load the stock Odex or stock deodex?? i do not need
Stock Kernel, insecure, init.d, sdcard R/W, selinux permissive ? thanks
How can i tell what boot loader version i have ?
download samsung info app from play store. or if have terminal emulator app on phone type in : su (enter = to grant superuser priv.)
type in : getprop ro.bootloader (enter = this will tell bootloader version).
first option is easiest/less chance (0%) for error/mistype.
"all I can really do, is stay out of my own way and let the will of heaven be done"
ok ...downloaded it but I dont see where it says what version example 4.3 or 4.4.2
Im attempting to load the ROM you recommended.
http://forum.xda-developers.com/showthread.php?t=2788357
Prerequisites include a minimum of a 4.3 bootloader and modem.
If you are not on the official 4.4.2 bootloaders and modem then you will need to flash ktoonsez kernel. http://forum.xda-developers.com/show....php?t=1756776
Directions:
1. Factory data reset
2. Flash ROM
3. If your still on 4.3 bootloader flash ktoonsez kernel immediately after the rom.
4. Let phone boot up, go through start up etc...
5. Open SuperSU, Let it disable Knox. If it gets stuck, press the home button and reboot the phone and try it again. It will work the 2nd time.
6. Nothing else to see here.
Got that ROM installed finally but the WiFi will not turn on
***Never mind reloaded the kernel and 2nd time and worked.
Related
I'll try and give as much info as possible so that hopefully this is easy to figure out.
My phone is a Samsung Galaxy s3 sch-r530u the US Cellular version. I didn't see a US Cellular forum and read someplace that it's the same as the at&t one so that's why I'm posting in here.
About a month or so ago I rooted and installed cyanogenmod with the installer and it installed I believe 11.1 maybe 11.2. The Android version my phone said it was I'm pretty sure was 4.4.2. Today in about phone in the settings I got a new version available message so I tried to do an update, which I was understanding that it was a cyanogenmod update and not a stock update but maybe I was wrong.
Right after the update my phone would boot to the boot screen with the blue robot guy on it and freeze basically. I was able to get into CWM and also into download mode. I did a little looking around and went into CWM and did the factory reset/wipe and cleared the cache and dalvik and that changed nothing.
Then I tried to flash the cyanogenmod 10.2 from inside CWM because I read someplace that it fixed the problem for someone else and it just failed when I tried. I also tried to fix via Kies and it isn't accepting my serial number for some reason. Then I found the teamuscellular website and grabbed both roms that say are stock roms and tried to flash both of those (not at the same time) via Odin and when I did the first one I got the something happened during firmware upgrade error.
I eventually fixed that by flashing the pit file with Odin and now I'm back to being stuck on the blue robot boot screen. When I try to flash either stock rom from teamuscellular in Odin they fail at some point and then I have to reflash the pit file again.
Somewhere along the line I couldn't get into CWM anymore and had to reflash that and I now have the philz touch 6.09.2 version of that.
I currently can get into both CWM and Download mode but for the life of me nothing I try works. When I go into Download mode what reads in the top left corner is this
odin mode, in red letters
Product name: SCH-R530U, in white letters
Custom binary download: Yes (4 counts), in white letters
Current Binary: Custom, in white letters
System Status: Custom, in white letters
Qualcomm Secureboot: Enable, in grey letters
Waranty bit: 1, in red letters
Bootloader Ap Swrev: 1, in grey letters
When I try and flash a rom and it fails I get some other line of text in red but I forget what it says
Any help is greatly appreciated
Thanks in advance
EDIT - Also a number of places directed me to samsungs updates websites to get the stock mod for my phone but there isn't one there for the SCH-R530U.
Also I'm looking at the how to guide for unbricking and I see something there about the status 7 error, which I do believe I got when I tried to flash the 2 teamuscellular stock mods but I don't remember for certain. I know one thing I didn't try was updating my bootloader.
I've also tried fixing with the simple upgrade tool and it fails also.
OK so I went ahead and tried the simple upgrade tool again to see the errors it gave me and in the bottom left corner of the program it had gone through a few things and failed when it said ABOOT.
And also at that same time on the download mode screen it added this line in red text at the bottom of the list in the top left corner on my phone screen
SW REV CHECKFAIL: FUSED1>Binary0
Based on a quick search, your phone supports CDMA and the AT&T version is GSM so they are not identical.
Your phone has the 4.3 bootloader with knox security. Since you flashed a custom recovery, it tripped the knox counter which voids any existing warranty.
The 4.3 bootloader cannot be downgraded to an older version and attempts to do so, either in download or recovery, may brick the phone.
In order to flash the phone in Odin, you would need to have a full and completely stock 4.3 ROM and not just a OTA update of the 4.3 ROM.
I suggest that you upgrade your recovery to the latest version and flash a custom ROM to try and get your phone functioning.
audit13 said:
Based on a quick search, your phone supports CDMA and the AT&T version is GSM so they are not identical.
Your phone has the 4.3 bootloader with knox security. Since you flashed a custom recovery, it tripped the knox counter which voids any existing warranty.
The 4.3 bootloader cannot be downgraded to an older version and attempts to do so, either in download or recovery, may brick the phone.
In order to flash the phone in Odin, you would need to have a full and completely stock 4.3 ROM and not just a OTA update of the 4.3 ROM.
I suggest that you upgrade your recovery to the latest version and flash a custom ROM to try and get your phone functioning.
Click to expand...
Click to collapse
OK. What exactly should I be looking for when you say I should upgrade my recovery? If I remember right I thought I removed that stupid Knox crap or maybe I just disabled it I forget exactly.
Thequass said:
OK. What exactly should I be looking for when you say I should upgrade my recovery? If I remember right I thought I removed that stupid Knox crap or maybe I just disabled it I forget exactly.
Click to expand...
Click to collapse
You can try and fix your phone by updating your recovery to the latest version of CWM for your phone. Then, download an install a custom ROM for your phone.
If you are not sure of what or how to do upgrade your recovery, don't do it until you have done some research and really understand the process.
As with any software change, there is no guarantee you won't brick your phone in the process.
Yeah I understand, I just wanted to make sure you meant CWM. So you think I should try reflashing a 4.3 custom rom over a 4.4? It was running 4.4.2 totally fine for a month ish.
If you want to install another ROM, I recommend doing a full wipe, including the system, cache, Davik, and data, before installing the new ROM.
I have switched between older and newer ROMs without a problem on my i747m.
Ok. I'll definitely wipe everything as I did in the past maybe there's one that I'm missing somehow. I wipe everything and somehow the blue robot boot screen is still there.
Thanks for all of your help. Your suggestions definitely led me in the right direction. I ended up finding a modified stock 4.3 with the bootloader file removed and since it seemed like my issues were related to that I figured what the hell I'll try it, I was almost at the point of going and getting a new phone anyhow. Because it wasn't completely bricked I wanted to try everything I could though and this worked!!!
Thanks again!!
Hi all my name is Blake and I'm a noob. (Sigh) thanks in advance for answering my stupid questions and being the awesome intelligent human bada$$es you are and helping teach me to better understand and operate my phone! So I rooted my phone a while back (4.3) or at least attempted it but I think Knox or something along those lines was preventing the process from completing so I had a friend help me out to complete the root so I'm still not 100% on how to do this. So I want to upgrade to 4.4 assuming it's better but more importantly my phone has a lot of quirks and bugs that annoy the living crap out of me and I won't waste u r time listing them unless you need me to and I'm hoping updating will solve some of them and if not I'll be back to forum surfing... anyways I'm rooted and need to know how to get to where I can get the ota update and then root it or however would be easiest to get the update and back to being rooted? I tried reading and understanding the existing threads but I'm still learning the terminology and i couldn't quite understand the ones i could find. Also this is probably a stupid question but is there an app or anything that will magically go through my phone and fix any stupid bugs and stuff!
Also to show my appreciation if u guys have like a YouTube channel i can like and subscribe to or anything i can do to show my appreciation I'd be glad to do so just send me a link thanks again you're my hero!
magikalbum said:
Also to show my appreciation if u guys have like a YouTube channel i can like and subscribe to or anything i can do to show my appreciation I'd be glad to do so just send me a link thanks again you're my hero!
Click to expand...
Click to collapse
I know you wanted a video I don't have all of the equipment to do so .. this is just a lot of words but simple easy steps.
Best possible solution for you if you really wanted the 4.4 update (nothing really has changed except the basic updates (firmware/modem)
... nothing noticeable except when you click on About Phone lol and you see 4.4.2 and the description of your system. That's really it.
But if you really want to give it a try the best solution for you is:
1 ALWAYS BACK UP YOUR PHONE!
This WILL BE UNROOTED BUT WILL GIVE THE OPTION TO BE ROOTED IF YOU WOULD LIKE
2 Download Odin if you haven't already and download the .tar file for 4.4.2 (the OTA Update)
When you extracted everything and opened Odin make sure Auto Reboot and F Reset Time is the ONLY ones checked.
3 Put the .tar file in PDA on Odin and put your phone in download mode (home, vol down, and power) when it comes up press vol up and it will show downloading .. it may show NOT RESPONDING give it a minute it usually will load up
Attach the usb cable from computer to phone once it registers it (will say added) click start. let it finish and you will have a complete wipe of 4.4.2 STOCK ROM --- UNROOTED!
FOLLOW THESE STEPS (COLOR MATCH) TO BE ROOTED ..... 4.4.2 ROOTED OR 4.3 ROOTED
-THIS IS THE START FOR BOTH --
1 Download your custom recovery (Philz or TWRP) ... I use Philz it's simple and and does everything for you to make sure it goes through.
2 Open Odin once more (same checked) turn your phone off wait for the vibration to indicate it is completely off then put it in download mode.
3 Place your recovery in PDA then attach phone and click start.
It will reboot just turn phone off and enter recovery mode (home, vol UP, and power). If the recovery doesn't show (sometimes it won't due to knox again) Then try again this way:
Phone off, place recovery in PDA, attach phone, and UNCLICK Auto-Reboot and push start. It will show downloading wait for Odin to show pass then boot in recovery from the screen you are on by just pushing home vol up and power. It should load that time.
Once it's loaded...
FOR 4.4.2 - ROOTED
3. Factory reset/clean to install new rom ...
DO NOT wipe cache just simply factory reset ..wait.. done ... clean to install new rom .. wait .. done.
If you do you will get a Status 7 or an error message.
4. Flash rom
5. Reboot
-It may ask you if you want to disable custom recovery make sure you hit NO!
You will need to update SU on playstore. And you should be good to go (had problems the first few times).
FOR 4.3 - ROOTED
DO NOT TRY FLASHING .TAR THROUGH ODIN. It will fail everytime because you can not downgrade firmware through it.
1. You will need to go back to stock unrooted with this HERE (MC2 Download only)
2 Make sure you have the MC2 Download -- or you will receive a Status 7 .. which means you don't have the right rom to update from.
3 Once you're on the MC2 firmware I believe it is the 4.2 version.
4 Turn off phone, enter recovery mode and flash this MC2 to Mk4 Rooted (NEED TO HAVE MC2 first!)
5 Reboot - if it asks to disable custom recovery make sure you press NO or it will unroot it at start up.
.
I was trying to carrier unlock my phone, and to do that i tried to downgrade it 4.3 to 4.1.1, and only after i had pressed the button, i had noticed that this might brick my phone in a comment in one of the forums, this is what i did:
http://forum.xda-developers.com/showthread.php?t=2625461
after following this and trying to run odin with it, odin returned "FAIL", and due to my high level of stupidity at the time, i tried to use the original 4.1.1 as my PDA in odin right after, i didnt reboot or anything, just pressed start again with the other tar.md5 file....
so now i cannot go past the samsung galaxy s3 logo when booting. I CAN go into download mode though, but i have no clue what i am supposed to do afterwards
i have the Galaxy S 3 i747 (was 4.3 before the whole mess) at&t carrier, i am trying to unlock it because i am travelling and need a phone.
please help me fix it, i do not care about the warranty since i dont have it anymore anyways, as long as the phone is working
also, if possible, i also need to unlock it afterwards, any help is HIGHLY appreciated, thanks!
baruchadi said:
I was trying to carrier unlock my phone, and to do that i tried to downgrade it 4.3 to 4.1.1, and only after i had pressed the button, i had noticed that this might brick my phone in a comment in one of the forums, this is what i did:
http://forum.xda-developers.com/showthread.php?t=2625461
after following this and trying to run odin with it, odin returned "FAIL", and due to my high level of stupidity at the time, i tried to use the original 4.1.1 as my PDA in odin right after, i didnt reboot or anything, just pressed start again with the other tar.md5 file....
so now i cannot go past the samsung galaxy s3 logo when booting. I CAN go into download mode though, but i have no clue what i am supposed to do afterwards
i have the Galaxy S 3 i747 (was 4.3 before the whole mess) at&t carrier, i am trying to unlock it because i am travelling and need a phone.
please help me fix it, i do not care about the warranty since i dont have it anymore anyways, as long as the phone is working
also, if possible, i also need to unlock it afterwards, any help is HIGHLY appreciated, thanks!
Click to expand...
Click to collapse
Downgrading your boot loader from 4.3 is a guaranteed brick. I'm not sure if the brick will get you to the Samsung screen.
If you're already assuming its bricked reboot into recovery and do a full wipe. Restore a nandroid of something if you have one or try flashing a custom ROM. Because Odin failed maybe it never flashed the boot loader.
Worth a try
Sent from my SGH-I747M using XDA Free mobile app
baruchadi said:
I was trying to carrier unlock my phone, and to do that i tried to downgrade it 4.3 to 4.1.1, and only after i had pressed the button, i had noticed that this might brick my phone in a comment in one of the forums, this is what i did:
http://forum.xda-developers.com/showthread.php?t=2625461
after following this and trying to run odin with it, odin returned "FAIL", and due to my high level of stupidity at the time, i tried to use the original 4.1.1 as my PDA in odin right after, i didnt reboot or anything, just pressed start again with the other tar.md5 file....
so now i cannot go past the samsung galaxy s3 logo when booting. I CAN go into download mode though, but i have no clue what i am supposed to do afterwards
i have the Galaxy S 3 i747 (was 4.3 before the whole mess) at&t carrier, i am trying to unlock it because i am travelling and need a phone.
please help me fix it, i do not care about the warranty since i dont have it anymore anyways, as long as the phone is working
also, if possible, i also need to unlock it afterwards, any help is HIGHLY appreciated, thanks!
Click to expand...
Click to collapse
Welcome to the forum! Wished you'd come in much earlier though as you would have found you CANNOT downgrade from 4.3 to 4.1.1 to free unlock. Sorry, but once you are on 4.3, the surest way to unlock is to obtain the unlock code from the carrier or purchase one online. Sounds like you do have a soft brick. If your phone is still booting to the Samsung logo, then it's only a soft brick. Attempting to downgrade the 4.3 bootloader usually results in a hard brick so you may be in luck.
To fix this first, try to see if you can boot to recovery mode and do a hard wipe/factory reset. If you are able to boot to recovery (or download) mode then you have little to worry about. If the reset does not work, you can flash custom recovery via Odin and follow the instructions in the thread below to restore stock 4.3. Afraid, you have to revert to full stock 4.3 to get the phone back in working order and don't even think about 4.1.1.
http://forum.xda-developers.com/showthread.php?t=2658486
If you are not able to get to recovery, then you can see if you can boot from a debrick image following the instructions (on the first page) of the thread below ...
http://forum.xda-developers.com/showthread.php?t=2549068
Once your phone is working normally, you can request the unlock code from AT&T via the request form below. If eligible, they should provide this. Otherwise, you would have to buy one online ....
https://www.att.com/deviceunlock/client/en_US/
Let me know if you need any further help.
KorGuy123 said:
Downgrading your boot loader from 4.3 is a guaranteed brick. I'm not sure if the brick will get you to the Samsung screen.
If you're already assuming its bricked reboot into recovery and do a full wipe. Restore a nandroid of something if you have one or try flashing a custom ROM. Because Odin failed maybe it never flashed the boot loader.
Worth a try
Sent from my SGH-I747M using XDA Free mobile app
Click to expand...
Click to collapse
I tried wiping everything, i also wiped cache, still didn't boot, thanks though!
Larry2999 said:
Welcome to the forum! Wished you'd come in much earlier though as you would have found you CANNOT downgrade from 4.3 to 4.1.1 to free unlock. Sorry, but once you are on 4.3, the surest way to unlock is to obtain the unlock code from the carrier or purchase one online. Sounds like you do have a soft brick. If your phone is still booting to the Samsung logo, then it's only a soft brick. Attempting to downgrade the 4.3 bootloader usually results in a hard brick so you may be in luck.
To fix this first, try to see if you can boot to recovery mode and do a hard wipe/factory reset. If you are able to boot to recovery (or download) mode then you have little to worry about. If the reset does not work, you can flash custom recovery via Odin and follow the instructions in the thread below to restore stock 4.3. Afraid, you have to revert to full stock 4.3 to get the phone back in working order and don't even think about 4.1.1.
http://forum.xda-developers.com/showthread.php?t=2658486
If you are not able to get to recovery, then you can see if you can boot from a debrick image following the instructions (on the first page) of the thread below ...
http://forum.xda-developers.com/showthread.php?t=2549068
Once your phone is working normally, you can request the unlock code from AT&T via the request form below. If eligible, they should provide this. Otherwise, you would have to buy one online ....
https://www.att.com/deviceunlock/client/en_US/
Let me know if you need any further help.
Click to expand...
Click to collapse
I am able to get to recovery, but the first link isn't very clear.... i am not really familiar with odin and all this other stuff... lol, i am now downloading the files it says to download in the first link though, can you maybe tell me in a quick list what exactly im supposed to do?
thanks!
baruchadi said:
I tried wiping everything, i also wiped cache, still didn't boot, thanks though!
I am able to get to recovery, but the first link isn't very clear.... i am not really familiar with odin and all this other stuff... lol, i am now downloading the files it says to download in the first link though, can you maybe tell me in a quick list what exactly im supposed to do?
thanks!
Click to expand...
Click to collapse
It's time to start reading. Before doing any flashing/modding, you should make sure you understand what you're doing and know the risks.
Now as for Odin, it's quite straight forward. Phone needs to be in download mode, you put the PDA file in Odin and flash (if it's a Odin one-click, just need to hit start). One thing is to not interrupt it! Especially if flashing bootloaders cause that will brick your phone. Also, don't downgrade bootloaders.
There are a few guides in the sticky, I suggest you take an hour or two reading them so things like that don't happen again (or that you know what to do if it does).
GL!
baruchadi said:
I tried wiping everything, i also wiped cache, still didn't boot, thanks though!
I am able to get to recovery, but the first link isn't very clear.... i am not really familiar with odin and all this other stuff... lol, i am now downloading the files it says to download in the first link though, can you maybe tell me in a quick list what exactly im supposed to do?
thanks!
Click to expand...
Click to collapse
Alright. If wipe/reset didn't work, you'll need to restore full stock 4.3 via custom recovery. Here's what we need to do....
1) Download the Odin flashable *.Tar file for custom recovery. I prefer TWRP because of the GUI so that's where I'm pointing you to ...
http://techerrata.com/file/twrp2/d2att/openrecovery-twrp-2.6.3.1-d2att.tar
2) Download the stock restore file for 4.3 from the thread below... If you are using TWRP, then the first link is the one you need
http://forum.xda-developers.com/showthread.php?t=2658486
3) Copy the stock restore zip file to a good quality (micro) SD card
4) I presume you have Odin already so you will use this to flash custom recovery to your phone. Run Odin.exe on your PC. If you are using Odin v.3.09 then you need the AP tab. For all other versions, use the PDA tab. Navigate to the custom recovery *.Tar file you downloaded earlier and place this in the PDA (or AP tab). Leave the default settings as is and do not check/uncheck any boxes other than the default settings.
5) Boot the phone to download mode via the 3-button combo (Volume Down/Home/Power). When you get to Odin (Download) mode, press volume up to continue. Connect the phone to your PC with a good quality micro USB cable. Wait until Odin has recognized the device then click on the Start button to start firmware installation (flashing). Wait for the flashing to end and the <Pass> message. Disconnect the phone from the PC and pull the battery to stop auto reboot.
6) Place the micro SD card with the stock restore zip in your phone. Replace the battery and boot to recovery mode. If you were successful with the firmware flashing above, it should boot you to custom recovery.
7) Select install from external card and navigate to the stock restore zip file. Select this file and swipe the screen to start firmware installation. Wait for installation to complete. Then clear your cache/dalvik and reboot to system.
This will hopefully do it.
Hello Everyone.
Please, I need some help. I was trying to downgrade an ATT Samsung Galaxy S3 from 5.0 to 4.1.1 and try to unlock it.
First, Try to flash with Odin 3.04, Odin 3.07 and Odin 3.09 with the firmware 4.1.1 from Samsung. It always failes.
So I rooted it , installed a team Win Recovery Project 2.6.3.1 and flashed a custom rom based on Android
4.1.2 thinking it will break the bootloader. Nothing.
I tried Emergency Recovery with Kies did not work.
In odin mode:
Product Name: SGH-I747
Current Binary: Custom
System Status: Custom
Qualcom Scoreboot: Enable
Warranty Bit:1
Bootloader AP SWREV:3
I spent hours on it. I don't know what to do.
Anyone has a idea to help me please?
Thanks you very much in advance.
If you can get into download mode, flash the latest Philz d2lte recovery using the tar.md5 file and Odin. Copy a ROM to an external SD card (I recommend the latest CM11), boot into recovery, flash the ROM, boot the phone. Once the phone boots, confirm your bootloader and modem version. I recommend not flashing anthing until you at least know your bootloader version.
Continuing to flash files without knowing the bootloader verson can hard brick you phone.
audit13 said:
If you can get into download mode, flash the latest Philz d2lte recovery using the tar.md5 file and Odin. Copy a ROM to an external SD card (I recommend the latest CM11), boot into recovery, flash the ROM, boot the phone. Once the phone boots, confirm your bootloader and modem version. I recommend not flashing anthing until you at least know your bootloader version.
Continuing to flash files without knowing the bootloader verson can hard brick you phone.
Click to expand...
Click to collapse
Thank you for your quick answer like you said i tried to flash cyanogen mod 11 and it aborted. How can I find out my bootloader version?
MEEEEEEEE said:
Thank you for your quick answer like you said i tried to flash cyanogen mod 11 and it aborted. How can I find out my bootloader version?
Click to expand...
Click to collapse
If you're on Philz touch, download AROMA file manager and store it on your external SD. You can get it here.
Boot into recovery and flash the file manager like you would install a ROM and it will open the file manager. Once you're up in the AROMA file manager, one of the menu options is to open a console. Once you're up in the console window the following command will tell you what bootloader you have loaded:
Code:
getprop ro.bootloader
That command will work from ADB shell in custom recovery too, if you happen to have ADB and all the drivers set up right on your computer.
What error did you get when flashing with Philz? Was it error 7?
Yes. It was a status 7. And I don't know what happens. Right now it looks hard bricked. I can not even it start it and put it on the downloading mode. When I plugged it to the power source without the battery. I have a big red led on and any responses. What is it? Can I go back to the downloading mode with a jig?
MEEEEEEEE said:
Yes. It was a status 7. And I don't know what happens. Right now it looks hard bricked. I can not even it start it and put it on the downloading mode. When I plugged it to the power source without the battery. I have a big red led on and any responses. What is it? Can I go back to the downloading mode with a jig?
Click to expand...
Click to collapse
Pull the battery, leave it out for a few minutes, then try to boot into recovery or download mode. This has cured some curious behavior for me a few times (just a shot in the dark though).
Another random thought, do you know how much battery power you had left? I'm a little surprised a failed CM flash would result in a hard brick when you still had download and recovery working before. Any chance the battery is dead? It won't charge without a working rom.
If that doesn't work and you can't get into recovery or download mode it might be time to move on to the debrick threads.
You may have to try a de-brick image. Status 7 usually occurs when the recovery is out of date.
jason2678 said:
Pull the battery, leave it out for a few minutes, then try to boot into recovery or download mode. This has cured some curious behavior for me a few times (just a shot in the dark though).
Another random thought, do you know how much battery power you had left? I'm a little surprised a failed CM flash would result in a hard brick when you still had download and recovery working before. Any chance the battery is dead? It won't charge without a working rom.
If that doesn't work and you can't get into recovery or download mode it might be time to move on to the debrick threads.
Click to expand...
Click to collapse
I tried to take the battery out and the flash is light on for a micro second but the phone does not boot. I can not go either in the recovery mode nor the downloading mode.
The is a custom rom on the phone. There is a slim kat v9 on it.
MEEEEEEEE said:
I tried to take the battery out and the flash is light on for a micro second but the phone does not boot. I can not go either in the recovery mode nor the downloading mode.
The is a custom rom on the phone. There is a slim kat v9 on it.
Click to expand...
Click to collapse
You did put the battery back in after pulling it for a couple of minutes, right? Looking back at my previous post it was poorly worded.
The fact that you went from working recovery and download to not working on a status 7 is curious. Usually status 7 errors are the developers trying to protect us from ourselves; your recovery is out of date, you are trying to flash a rom that isn't for your phone or doesn't like your bootloader, something like that. When you get a status 7, usually the recovery didn't actually do anything. It failed a safety check and quit. That's what made me wonder if maybe your battery just died.
So you flashed CM11 for the d2lte using the latest version of Philz? Did you flash anything else?
Actually I gave the cellphone to someone few days ago and he told me that I needed to unlock the bootloader and install EZ-unlock. Unlocked the bootloader. Philz is still on the recovery partition. The firmware flashed is slim kat v9. Since the bootloader has been unlocked. The phone does not want to start. I tried to take out the battery for few minutes. it does not change anything.
MEEEEEEEE said:
Actually I gave the cellphone to someone few days ago and he told me that I needed to unlock the bootloader and install EZ-unlock. Unlocked the bootloader. Philz is still on the recovery partition. The firmware flashed is slim kat v9. Since the bootloader has been unlocked. The phone does not want to start. I tried to take out the battery for few minutes. it does not change anything.
Click to expand...
Click to collapse
the phone wont start because the i747 bootloader does not come locked. what ez-unlock does for this device is effectively BRICK it!!!!! i know because thats how i bricked my first i747. now you really do need the debrick image. when plugged in , without battery does the led show red ?
http://forum.xda-developers.com/showthread.php?t=2549068
"all i can really do , is stay out of my own way and let the will of heaven be done"
Yes. The red led is showing when I plugged the device without the battery.
mrrocketdog said:
the phone wont start because the i747 bootloader does not come locked. what ez-unlock does for this device is effectively BRICK it!!!!! i know because thats how i bricked my first i747. now you really do need the debrick image. when plugged in , without battery does the led show red ?
http://forum.xda-developers.com/showthread.php?t=2549068
"all i can really do , is stay out of my own way and let the will of heaven be done"
Click to expand...
Click to collapse
MEEEEEEEE said:
Yes. The red led is showing when I plugged the device without the battery.
Click to expand...
Click to collapse
pretty positive sign of a brick if thats all you can get. check the link for the "de-brick" thread that i posted. remember that sometimes it takes more than one try , and while one sdcard will work for one phone , it may or may not work for another. just keep trying. good luck.:thumbup:
"all i can really do , is stay out of my own way and let the will of heaven be done"
Do I need to get a jig to un-bricked it?
MEEEEEEEE said:
Do I need to get a jig to un-bricked it?
Click to expand...
Click to collapse
nope. read the thread. a de-brick image and sdcard should do it.
"all i can really do , is stay out of my own way and let the will of heaven be done"
A jig would be helpful if the phone boots but you can't get into download mode.
My Galaxy Note 2 is stuck at the Start up screen screen. Where its an all black bg and simply says Samsung Galaxy Note II
I have tried using recovery mode, cleared cache, and reset to factory. Neither troubleshoot method worked.
I have tried numerous Odin autoroots. none work. Whenever I try to root it fails. Im guessing it might be because I dont have Dev Debug enable and I cant get into my phone to enable it. because of this issue
I have tried looking for TWRP .tar but every file I download the file is always a .img
The Model of the phone is a SGH-T889 (T-mobile Note II)
I am all out of ideas, and I dont know what to do. I have been search for answers for hours and everytime I think I found a solution it doesnt work.
What ROM was your phone on when this happened ?
Can you get int to download mode ? If yes try flashing stock ROM and see if it helps.
ciphercodes said:
What ROM was your phone on when this happened ?
Can you get int to download mode ? If yes try flashing stock ROM and see if it helps.
Click to expand...
Click to collapse
It was on the offical default rom. the phone was never modded, or rooted.
My niece downloads a bunch of kiddie games onto the phone, we constantly have to uninstall them. My thoughts and the T-mobile tech suspects that it the crash may have been caused my too many updates or a bad updated file most likely due to the games or game.
I can get the phone into download mode, and recovery mode.
In reovery mode I have 6 options
reboot system now
apply update from ADB
apply update from external storage
wipe data/factory reset
wipe cashe partition
apply update from cache
I have tried Apply update from cache, Wipe cache partition, then Wipe data.factory reset. I also attempted to put a CF auto root .md5 file and a KIES .md5 file which I believe is a stock firmware file on a SD card. to try to use the apply update from external storage option, but neither file showed up when I went into the option. So I guess I didnt have the right sort of file.
So recovery didnt work so I tried using Odin v3.07 and Odin v3.09 with CF auto root files for the SGH-T889, that didnt work, ecerytime I tried to apply it, It was always Fail within seconds. I tried other root files that are made for other versions of the Galaxt Note 2 like the GT-N1700 but those also simply failed.
I tried using what I believe to be stock frimware files with Odin. and those also Failed.
Im not exactly the best person with these. I learn mostly what I know from the internet and reading various forums, youtube videos, and other people experiences. I cannot find anyone who's problem has not yet been fixed through the above methods. so I really dont know where to go from here.
I think the reason I cant Flash from PC is because it might be possible USB Debugging is not enabled. Not sure if this is what is causing all the Fails in odin
BramaKnox said:
It was on the offical default rom. the phone was never modded, or rooted.
My niece downloads a bunch of kiddie games onto the phone, we constantly have to uninstall them. My thoughts and the T-mobile tech suspects that it the crash may have been caused my too many updates or a bad updated file most likely due to the games or game.
I can get the phone into download mode, and recovery mode.
In reovery mode I have 6 options
reboot system now
apply update from ADB
apply update from external storage
wipe data/factory reset
wipe cashe partition
apply update from cache
I have tried Apply update from cache, Wipe cache partition, then Wipe data.factory reset. I also attempted to put a CF auto root .md5 file and a KIES .md5 file which I believe is a stock firmware file on a SD card. to try to use the apply update from external storage option, but neither file showed up when I went into the option. So I guess I didnt have the right sort of file.
So recovery didnt work so I tried using Odin v3.07 and Odin v3.09 with CF auto root files for the SGH-T889, that didnt work, ecerytime I tried to apply it, It was always Fail within seconds. I tried other root files that are made for other versions of the Galaxt Note 2 like the GT-N1700 but those also simply failed.
I tried using what I believe to be stock frimware files with Odin. and those also Failed.
Im not exactly the best person with these. I learn mostly what I know from the internet and reading various forums, youtube videos, and other people experiences. I cannot find anyone who's problem has not yet been fixed through the above methods. so I really dont know where to go from here.
I think the reason I cant Flash from PC is because it might be possible USB Debugging is not enabled. Not sure if this is what is causing all the Fails in odin
Click to expand...
Click to collapse
Lets see if we can get this resolved.
1) Do you remember what version of Android the phone was on 4.3 or 4.1.2 ?
2) Put your phone in download mode then connect to your computer via usb. Start Odin in admin mode (right click and run as admin).
3) Now do you see ID:COM section turn blue ? Under message you can see "Added!". If you see this then phone is recognized by Odin.
4) If your phone was on 4.3 then download this most up to date firmware - from here http://www.sammobile.com/firmwares/download/22863/T889UVUCMK7_T889TMBCMK7_TMB/
5) Once downloaded, extract the file(use 7zip or winrar), once extracted you will see a file with .md5 extension.
6) Now going back to ODIN, click on PDA and then browse to this file which you just extracted.
7) This takes some time, once done you should see a message like "Checking MD5 finished successfully", "Leave CS".
8) You can leave Auto reboot and F-reset time checked.
9) Now click Start and let the process finish.
10) If everything goes fine you should see a green message "Pass"
Let me know how it goes.
I have the same problem as the OP (boots only up to Samsung logo with black bg) but it was not caused by niece downloading games but instead from trying to install jedi masterx2 rom.
I did what ciphercodes recommended and put phone in download mode and odin went through the motions of installing the stock os (in my case version 4.3) but after apparently installing the rom it again booted up to Samsung note II logo in black bg.
luckily I can install either Clockword mod recovery v6.0.4.3 or teamwin v2.8.6.0
The clockword mod recovery can read the external sd card (whereas funnily enough the teamwin can't) and I can attempt recovery from previous backups on cmr or to install a rom from zip file but neither of these work - reboots again to Samsung logo in black background after apparently installing the rom.
both teamwin and cwr mention that they can't mount system and that's probably why no rom is install either using cwr or odin so my guess is that I have to reformat the partitions cause probably efs file is corrupt but I don't know how to do that and I have done extensive search in google but have not found a solution
so ciphercodes if you or anyone reading this can help please reply to this message
ciphercodes said:
Lets see if we can get this resolved.
1) Do you remember what version of Android the phone was on 4.3 or 4.1.2 ?
2) Put your phone in download mode then connect to your computer via usb. Start Odin in admin mode (right click and run as admin).
3) Now do you see ID:COM section turn blue ? Under message you can see "Added!". If you see this then phone is recognized by Odin.
4) If your phone was on 4.3 then download this most up to date firmware - from here
5) Once downloaded, extract the file(use 7zip or winrar), once extracted you will see a file with .md5 extension.
6) Now going back to ODIN, click on PDA and then browse to this file which you just extracted.
7) This takes some time, once done you should see a message like "Checking MD5 finished successfully", "Leave CS".
8) You can leave Auto reboot and F-reset time checked.
9) Now click Start and let the process finish.
10) If everything goes fine you should see a green message "Pass"
Let me know how it goes.
Click to expand...
Click to collapse
I am uncertain of which version the phone was on. If you need I can call t-mobile and have them tell me which version it was on.
I did these steps. the file took a hour to download. and It still didn't work. I follow all steps down to the exact. and when I pressed start. within one second it said FAIL. just the other attempts I made.
BramaKnox said:
I am uncertain of which version the phone was on. If you need I can call t-mobile and have them tell me which version it was on.
I did these steps. the file took a hour to download. and It still didn't work. I follow all steps down to the exact. and when I pressed start. within one second it said FAIL. just the other attempts I made.
Click to expand...
Click to collapse
Unless your t889 Note II was sitting in a drawer and not being updated for the last year or so you probably have 4.3
When you go to download mode do you see "custom binary download: yes ..."
and do you see "knox warranty void:" ?
if so, your phone has been rooted.
but unlike your case, when I try to install stock rom through Odin, it goes through the motions of installing and gives message pass - that is that the stock rom has been installed, but unfortunately it has not installed any rom that my phone can read.
koyanishi said:
Unless your t889 Note II was sitting in a drawer and not being updated for the last year or so you probably have 4.3
When you go to download mode do you see "custom binary download: yes ..."
and do you see "knox warranty void:" ?
if so, your phone has been rooted.
but unlike your case, when I try to install stock rom through Odin, it goes through the motions of installing and gives message pass - that is that the stock rom has been installed, but unfortunately it has not installed any rom that my phone can read.
Click to expand...
Click to collapse
No it says
Product Name: SGH-T889
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Official
Knox Warranty Void: 0
RP SWAEV: A2
BramaKnox said:
No it says
Product Name: SGH-T889
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Official
Knox Warranty Void: 0
RP SWAEV: A2
Click to expand...
Click to collapse
Then you have an un rooted 4.3 rom because the 4.1.2 did not have knox
koyanishi said:
Then you have an un rooted 4.3 rom because the 4.1.2 did not have knox
Click to expand...
Click to collapse
Okay thank you, well then link ciphercodes gave me for the firmware was the right one. But still Failed. *Sigh*
BramaKnox said:
Okay thank you, well then link ciphercodes gave me for the firmware was the right one. But still Failed. *Sigh*
Click to expand...
Click to collapse
Since your phone is not rooted then I think that ciphercodes advice will not work as you can only install a stock rom that way only if your phone is first rooted.
Probably you should try to root your phone using instructions from this thread
http://forum.xda-developers.com/showthread.php?t=2562994
But this might not work for you as it could be that efs file is corrupted or something else as we both boot up to a black screen that only has Samsung logo
koyanishi said:
Since your phone is not rooted then I think that ciphercodes advice will not work as you can only install a stock rom that way only if your phone is first rooted.
Probably you should try to root your phone using instructions from this thread
http://forum.xda-developers.com/showthread.php?t=2562994
But this might not work for you as it could be that efs file is corrupted or something else as we both boot up to a black screen that only has Samsung logo
Click to expand...
Click to collapse
Yeah the chainfire root fail as well. I have tried every file for all the Galaxy II's including mines. none work. Always FAIL in Odin. I'm guessing there is just nothing I can do
BramaKnox said:
Yeah the chainfire root fail as well. I have tried every file for all the Galaxy II's including mines. none work. Always FAIL in Odin. I'm guessing there is just nothing I can do
Click to expand...
Click to collapse
Since your phone is not rooted you may be able to get it repaired under warranty. I think that Samsung warranty is only good for a year, but if you purchased your phone with a American Express gold card (I think other gold cards will also apply) your warranty is extended to double what the original was. So perhaps you have a chance to have your credit card pay for the repair.
Otherwise:
I am no expert but if you want to continue playing with your phone before you get expert advice you may want to play with the recovery mode. To enter recovery mode press volume up and home and power buttons at the same time. once you feel vibrate or after a while release the power button but continue to hold volume up and home buttons and then you will enter recovery mode. you may want to go to menu that says wipe data/factory reset and see if that works. It may be that it is like my phone and the system cannot be mounted in which case you will get that message. After you are through to get out of this menu remove the battery.
But please be aware that I am no expert and you are using this info at your own risk
but I think of doing something catastrophic using this advice in my non expert opinion is small.
koyanishi said:
Since your phone is not rooted you may be able to get it repaired under warranty. I think that Samsung warranty is only good for a year, but if you purchased your phone with a American Express gold card (I think other gold cards will also apply) your warranty is extended to double what the original was. So perhaps you have a chance to have your credit card pay for the repair.
Otherwise:
I am no expert but if you want to continue playing with your phone before you get expert advice you may want to play with the recovery mode. To enter recovery mode press volume up and home and power buttons at the same time. once you feel vibrate or after a while release the power button but continue to hold volume up and home buttons and then you will enter recovery mode. you may want to go to menu that says wipe data/factory reset and see if that works. It may be that it is like my phone and the system cannot be mounted in which case you will get that message. After you are through to get out of this menu remove the battery.
But please be aware that I am no expert and you are using this info at your own risk
but I think of doing something catastrophic using this advice in my non expert opinion is small.
Click to expand...
Click to collapse
Yeah the warranty is expired. and I have tried recovery mode. thats actually the first step before trying to apply a firmware. So recovery hasnt worked either. Guess I will just have to get a new phone. thank you all for oyu help tho. I apperciate it
I was just reading through the thread.. It doesnt seem like you tried flashing Tmobiles Stock 4.3 Firmware in download mode. If you tried to flash a 4.1.2 Firmware when the phone was already updated then I think thats where it failed. Try again but with the 4.3 Firmware through ODIN. After it finishes try rebooting it manually and/or if it doesnt boot again then go back into recovery and factory/data reset again...shouldnt hurt to try..
Double0EK said:
I was just reading through the thread.. It doesnt seem like you tried flashing Tmobiles Stock 4.3 Firmware in download mode. If you tried to flash a 4.1.2 Firmware when the phone was already updated then I think thats where it failed. Try again but with the 4.3 Firmware through ODIN. After it finishes try rebooting it manually and/or if it doesnt boot again then go back into recovery and factory/data reset again...shouldnt hurt to try..
Click to expand...
Click to collapse
From my knowledge the other person who first replied gave me 4.3 firmeware fild link. But in the chances of it could u provide me with a link to a 4.3 firmware u believe will work, because all the ones I found have not worked