Hi,
I've using CM 11 for a while on my HOX. I didn't have the backup of my original ROM. I didn't think I'd need to sell the phone but I wanted to and I was told to restore the stock ROM back. I thought I got the correct RUU and when I tried to flash (after relocking bootloader and erasing cache), I was told by RUU GUI that there was a bootloader version problem. Reading about it, I found that my HBOOT version is 1.72.0000 and the RUU showed something like 1.29.
After reading further I found that I was downgrading the HBOOT and for that I need to have S-OFF (I have S-ON).
I then extracted the ROM.zip file from the RUU and tried to flash the system.img and boot_signed.img files and found myself in a situation where the phone goes into a boot loader loop.
The battery has been dead and I'm also plagued by the power management bug in HOX ( doesn't charge at all and had to leave it on for days). Luckily it started charging again but since the phone goes into a bootloader loop, the battery is dying.
I found the fastboot-battery-recharge on this forum where I'm trickle charging it.
Can you help me flash the original ROM back by identifying the correct RUU (android files. org)?
My phone details:
F:\HOX>fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.72.0000
(bootloader) version-baseband: 5.1204.164D3.31
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 4.17.161.3
(bootloader) serialno: XXXX
(bootloader) imei: XXXX
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ4610000
(bootloader) cidnum: VODAP001
(bootloader) battery-status: low
(bootloader) battery-voltage: 3547mV
(bootloader) devpower: 0
(bootloader) partition-layout: None
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
I downloaded this RUU: RUU_ENDEAVOR_U_JB_45_S_HTC_Europe_3.14.401.31_R_Radio_5.1204.162.29_release_302015_signed.exe
Would this work when the phone is charged?
Please assist as I want to sell the phone.
Thanks in advance guys.
The battery seems to have charged a little bit and I tried the RUU mentioned above, but it doesn't run fully. I get the initial messages to accept about battery being 30% etc, and then I'm shown the current image versoin 4.17.xxx and then the "Update" button. When I click it, the RUU just closes. I'm trying to download another RUU: RUU_ENDEAVOR_U_JB_45_S_HTC_Europe_3.14.401.27_Radio_5.1204.162.29_release_298897_signed.exe
In case there was something wrong with the ROM..
The flashing of the second RUU failed this time with error 158. Incorrect RUU. So I went ahead and unlocked bootloader again and CM is back working now thankfully. I still don't know how to flash it with stock ROM correctly. I'm reading about downloading some Nandroid backups 3.20.x versions and restoring it.
I don't want to risk anymore, so please let me know.
Standing by.........
corpuscallosum said:
The flashing of the second RUU failed this time with error 158. Incorrect RUU. So I went ahead and unlocked bootloader again and CM is back working now thankfully. I still don't know how to flash it with stock ROM correctly. I'm reading about downloading some Nandroid backups 3.20.x versions and restoring it.
I don't want to risk anymore, so please let me know.
Standing by.........
Click to expand...
Click to collapse
You will never succsses to flash RUU no RUU for this high main version restore nandroid or install custom rom on it
Ok thank you. That clarifies about RUU flashing. I have downloaded 3.14 (VODAP0001) Nandroid from one of pages of this site and follow the instructions to flash. Hopefully I'll get stock ROM back then.
Do I need to have the stock recovery also? Is stock recovery required for OTA and when factory reset on the stock ROM it would revert back to factory state (going through setup process again)?
corpuscallosum said:
Ok thank you. That clarifies about RUU flashing. I have downloaded 3.14 (VODAP0001) Nandroid from one of pages of this site and follow the instructions to flash. Hopefully I'll get stock ROM back then.
Do I need to have the stock recovery also? Is stock recovery required for OTA and when factory reset on the stock ROM it would revert back to factory state (going through setup process again)?
Click to expand...
Click to collapse
3.14 will not work you will have problem with the tuch will not work you need nandroid with your numbers. Yes stock recovery is need for OTA but you are with latest base I think
Ok. I think I'm having trouble identifying the correct versions then. I thought 3.14 is the bootloader version. Is that the baseband version then?
Since I have 5.1204, do I need to download a Nandroid 5.1204 version?
Can i get some help please unbricking mine i cant seem to find the correct ruu any where ive already relocked the bootloader and now ive been stuck with out a phone for 2 weeks
X:\Fastboot>fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.72.0000
(bootloader) version-baseband: 5.1204.164D3.31
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 4.17.161.3
(bootloader) serialno: SH25AW109670
(bootloader) imei: 354461055970384
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ4610000
(bootloader) cidnum: VODAP001
(bootloader) battery-status: good
(bootloader) battery-voltage: 3793mV
(bootloader) devpower: 71
(bootloader) partition-layout: None
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 1.050s
this is all ive got id really apreciate any help
corpuscallosum said:
Ok. I think I'm having trouble identifying the correct versions then. I thought 3.14 is the bootloader version. Is that the baseband version then?
Since I have 5.1204, do I need to download a Nandroid 5.1204 version?
Click to expand...
Click to collapse
you need nand backup with this numbers 4.17.161.3 this with the red is important dont look your CID if you find nand with this numbers is the prfect like 4.18.401.4 this with the red is WWE region, in your case is 161 maybe this is Vodafone I don't know Germany or UK
---------- Post added at 11:34 PM ---------- Previous post was at 11:33 PM ----------
RayOneX said:
Can i get some help please unbricking mine i cant seem to find the correct ruu any where ive already relocked the bootloader and now ive been stuck with out a phone for 2 weeks
X:\Fastboot>fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.72.0000
(bootloader) version-baseband: 5.1204.164D3.31
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 4.17.161.3
(bootloader) serialno: SH25AW109670
(bootloader) imei: 354461055970384
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ4610000
(bootloader) cidnum: VODAP001
(bootloader) battery-status: good
(bootloader) battery-voltage: 3793mV
(bootloader) devpower: 71
(bootloader) partition-layout: None
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 1.050s
this is all ive got id really apreciate any help
Click to expand...
Click to collapse
If you read the hole thread you will see no RUU for this main version and unlock your bootloader and flash recovery and then custom rom or nand backup with this numbers 4.17.161.3
Thant said:
you need nand backup with this numbers 4.17.161.3 this with the red is important dont look your CID if you find nand with this numbers is the prfect like 4.18.401.4 this with the red is WWE region, in your case is 161 maybe this is Vodafone I don't know Germany or UK
---------- Post added at 11:34 PM ---------- Previous post was at 11:33 PM ----------
If you read the hole thread you will see no RUU for this main version and unlock your bootloader and flash recovery and then custom rom or nand backup with this numbers 4.17.161.3
Click to expand...
Click to collapse
Can i please get help doing this with a step by step instruction list or even links please
---------- Post added at 05:38 PM ---------- Previous post was at 05:29 PM ----------
RayOneX said:
Can i please get help doing this with a step by step instruction list or even links please
Click to expand...
Click to collapse
Nandroid Backup 4.17.161.2 CID VODAP001 thanks to alextheg will this be okay its from this page http://forum.xda-developers.com/showthread.php?t=1975140
Thant, thanks. I guess 4.17.161.3 is for me. I'll see if there's a uk based VODAP001.
I will use this: 4.17.161.2 CID VODAP001. Will follow the steps mentioned where I got the Nand backup itself.
wohoo!! I got the 'stock' ROM back!! Thanks Thant! You're brilliant! I also copied the recovery.img from the Nand backup. Can I flash that with cmd: "fastboot flash recovery recovery.img"? Can I erase cache and relock bootloader to see if I get OTA? Is that the correct way forward?
corpuscallosum said:
wohoo!! I got the 'stock' ROM back!! Thanks Thant! You're brilliant! I also copied the recovery.img from the Nand backup. Can I flash that with cmd: "fastboot flash recovery recovery.img"? Can I erase cache and relock bootloader to see if I get OTA? Is that the correct way forward?
Click to expand...
Click to collapse
you need stock recovery not this in the backup search for stok recovery for your base or download OTA and choice install later then take the recovery from OTA and flash it
Fixed!! HOX stuck in bootloop and cannot restore ROM
Perfect! I choose install later when the OTA came up on the phone, connected it to my computer and navigated to the download folder on my phone. Found the file : "OTA_ENDEAVOR_U_JB_50_S_Vodafone_UK_4.17.161.3-4.17.161.2_release_369941".
Extracted recovery.img from the firmware.zip file within, copied to my computer, put the phone in fastboot mode and flashed the recovery using command: fastboot flash recovery recovery.img.
That was it. Rebooted the phone and installed the OTA without any issues!!
It back to factory state. Thanks a million Thant!!
corpuscallosum said:
Perfect! I choose install later when the OTA came up on the phone, connected it to my computer and navigated to the download folder on my phone. Found the file : "OTA_ENDEAVOR_U_JB_50_S_Vodafone_UK_4.17.161.3-4.17.161.2_release_369941".
Extracted recovery.img from the firmware.zip file within, copied to my computer, put the phone in fastboot mode and flashed the recovery using command: fastboot flash recovery recovery.img.
That was it. Rebooted the phone and installed the OTA without any issues!!
It back to factory state. Thanks a million Thant!!
Click to expand...
Click to collapse
Good to hear that
Related
I need to return my International HTC One M8 back to stock, I currently run with TWRP and Revolution 11.1 ROM.
My M8 is NOT S-OFF
I have found a guide that tells me how to achieve this, one of the first things it asks is to make note of the CID and version-main.
I have the CID of HTC__001, but my version-main is empty.
This is a problem as the HTC__001 nandroid backups (and recovery images) have two versions available as you can see below (1.54.xxx.xx and 2.22.xxx.xx)
CID HTC__001
1.54.401.10 - CWM Philz touch Thanks to spikeydoo2006
1.54.401.5 - TWRP Thanks to Fisha21
1.54.401.5 - CWM Philz touch Thanks to krihoum
1.54.401.5 - TWRP Thanks to jontyjon
1.54.401.10 - TWRP Thanks to ckpv5
2.22.401.4 - TWRP Thanks to ckpv5
2.22.401.5 - TWRP Thanks to ckpv5
2.22.401.5 - CWM Philz touch Thanks to MATRIKS
I have no idea what to do at this point, Google searching hasnt given me a definitive answer, can anyone here help and point me in the right direction please?
If its of any use..
HBOOT 3.18.0.000
RADIO 1.19.2331147A1.09G
Hboot 3.18 is at least 2.22 so i suggest you take the 2.22.401.4 and the 2.22.401 stock recovery. Restore the nand and then flash back the stock recovery. Then perform the available OTA and you are back on the latest stock rom
Mr Hofs said:
Hboot 3.18 is at least 2.22 so i suggest you take the 2.22.401.4 and the 2.22.401 stock recovery. Restore the nand and then flash back the stock recovery. Then perform the available OTA and you are back on the latest stock rom
Click to expand...
Click to collapse
Just the job, cheers.
All sorted now and back to stock with OTA capabilities and RELOCKED boot loader.
Thanks for your pointer.
Mr Hofs said:
Hboot 3.18 is at least 2.22 so i suggest you take the 2.22.401.4 and the 2.22.401 stock recovery. Restore the nand and then flash back the stock recovery. Then perform the available OTA and you are back on the latest stock rom
Click to expand...
Click to collapse
Sir, I have the same problem after rooting and flashing TWRP. Except that I am running an HBOOT of 3.19.0000. My software number is 3.28.709.5 and my CID is HTC__621. From the stock Nandroids backup link that everyone is using, I find 2 major software versions under that CID number. Is it also safe to flash the 2..22.709.4 version then? And also is there any possible way to reclaim version-main after processing any OTA updates and rooting again? Am i rooting it the wrong way or flashing the incorrect recovery to begin with? I use Hasoon's AIO Tool to flash.
Thanks!
Sorry to OP for hijacking your thread!
Main is BLANK - Help to find out stock recovery image FILE for HTC ONE M8 taiwan make
Hi Experts ,
Pl help to find out exact stock recovery image for HTC ONE M8 TAIWAN Model to roll back from TWRP.
Details:
1. I flashed TWRP "openrecovery-twrp-2.7.1.0-m8.img" on my HTC__621 using Fastboot ADB
2. Found list of CID for my Firmware(HTC__621) in http://forum.xda-developers.com/show....php?t=2545227
3. Fast boot command resulted in BLANK Main version to get the stock recovery image.
Details on the Fast boot with S-ON, rooted and unlocked:
C:\fastboot>fastboot oem readcid
...
(bootloader) cid: HTC__621
OKAY [ 0.002s]
finished. total time: 0.004s
C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.22.21331147A1.29G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: HT4C1WM01867
(bootloader) imei:
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: df77f8b7
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.021s
PLEASE HELP TO ROLL BACK TO STOCK RECOVERY and suggest me a good ROM but my SECURITY IS ON.
bharaka said:
Hi Experts ,
Pl help to find out exact stock recovery image for HTC ONE M8 TAIWAN Model to roll back from TWRP.
Details:
1. I flashed TWRP "openrecovery-twrp-2.7.1.0-m8.img" on my HTC__621 using Fastboot ADB
2. Found list of CID for my Firmware(HTC__621) in http://forum.xda-developers.com/show....php?t=2545227
3. Fast boot command resulted in BLANK Main version to get the stock recovery image.
Details on the Fast boot with S-ON, rooted and unlocked:
C:\fastboot>fastboot oem readcid
...
(bootloader) cid: HTC__621
OKAY [ 0.002s]
finished. total time: 0.004s
C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.22.21331147A1.29G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: HT4C1WM01867
(bootloader) imei:
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: df77f8b7
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.021s
PLEASE HELP TO ROLL BACK TO STOCK RECOVERY and suggest me a good ROM but my SECURITY IS ON.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=3019919
And please don't post the same message in about 5 or even more threads. Keep it in one because it's hard to follow like this ! Thank you
Stock recovery for M8 -
Thanks. Will keep my updates in the scope of this thread.
I am using TWRP. Couldn't find the stock recovery for my M8 Taiwan make HTC__0621. Details of the Firmware are inline in this thread.
Please help me to get the stock recovery image. Whether i can take it from the lollipop OTA Zip?
Kindly share your Expertise
Mr Hofs said:
http://forum.xda-developers.com/showthread.php?t=3019919
And please don't post the same message in about 5 or even more threads. Keep it in one because it's hard to follow like this ! Thank you
Click to expand...
Click to collapse
bharaka said:
Thanks. Will keep my updates in the scope of this thread.
I am using TWRP. Couldn't find the stock recovery for my M8 Taiwan make HTC__0621. Details of the Firmware are inline in this thread.
Please help me to get the stock recovery image. Whether i can take it from the lollipop OTA Zip?
Kindly share your Expertise
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=58417966&postcount=3926
Hi Ckpy,
Still i am not clear on the STOCK RECOVERY Version for my model HTC__621. Please suggest.
Details again i am giving below,
Details:
1. I flashed TWRP "openrecovery-twrp-2.7.1.0-m8.img" on my HTC__621 using Fastboot ADB
2. Found list of CID for my Firmware(HTC__621) in http://forum.xda-developers.com/show....php?t=2545227
3. Fast boot command resulted in BLANK Main version to get the stock recovery image.
Details on the Fast boot with S-ON, rooted and unlocked:
C:\fastboot>fastboot oem readcid
...
(bootloader) cid: HTC__621
OKAY [ 0.002s]
finished. total time: 0.004s
C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.22.21331147A1.29G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: HT4C1WM01867
(bootloader) imei:
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: df77f8b7
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.021s
PLEASE HELP TO ROLL BACK TO STOCK RECOVERY and suggest me a good ROM but my SECURITY IS ON.
bharaka said:
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.22.21331147A1.29G
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
PLEASE HELP TO ROLL BACK TO STOCK RECOVERY and suggest me a good ROM but my SECURITY IS ON.
Click to expand...
Click to collapse
You need 3.28.709.6 stock recovery.
Then later you can do OTA to lollipop 4.16.709.9
I can't suggest a good ROM as I don't use custom ROM, only my own made ROM.
After you update to Lollipop, you can try all the available Sense Custom ROM then decide on your own which one suit you the best.
Hi CkpV5,
Please suggest me where to get the IMAGE for STOCK recovery 3.28.709.6. Please help to to understand how you came to find out the correct stock for htc m8.
I forgot to mention that TWRP that i used is for HTC M8 GSM model.
bharaka said:
Hi CkpV5,
Please suggest me where to get the IMAGE for STOCK recovery 3.28.709.6. Please help to to understand how you came to find out the correct stock for htc m8.
I forgot to mention that TWRP that i used is for HTC M8 GSM model.
Click to expand...
Click to collapse
You don't read the link that I posted before ?
http://forum.xda-developers.com/showpost.php?p=58417966&postcount=3926
You details that I shortlisted in previous post tell me your stock version.
Hi CKPV5,
Thanks. I read your previous reply and downloaded the IMAGE 3.28.709.6 but there was another version of stock 4.16.709.9. so bit confused.
Can i flash this stock IMAGE 3.28.709.6? Is it based on the model number that you decide the STOCK?
Cheers,
-BharathI MU
bharaka said:
Hi CKPV5,
Thanks. I read your previous reply and downloaded the IMAGE 3.28.709.6 but there was another version of stock 4.16.709.9. so bit confused.
Can i flash this stock IMAGE 3.28.709.6? Is it based on the model number that you decide the STOCK?
Cheers,
-BharathI MU
Click to expand...
Click to collapse
use 3.28.709.6 as this is what your device need based on your hboot no and radio version no.
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.22.21331147A1.29G
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
then do OTA update, it will update your software to lollipop 4.16.709.9
Thank you Very much. I UPDATED MY STOCK RECOVERY USING IMAGE "3.28.709.6_recovery.img". Below is the output on my bootloader screen,
Pl confirm is this the correct output on the stock recovery screen.
1. Screen displays an Red Exclamation mark.
2. In the bottom of the screen there is a yellow display with the output : Device_CW_Install:No CW files. Skip cw installation. Write host_mode:0 done
Please confirm
Yes.. that's stock recovery
Now.. reboot, go settings-about-software update - do update checking - download - install OTA
If there is no problem with your current ROM, it will update it to lollipop
Hi,
My SECURITY IS ON - S-ON. I tried using Firewater and it was discontinued. In my STOCK RECOVERY, there was a TAMPERED word visible.
I UNLOCKED AND ROOTED.
Pl Help how to setup lollipop. I tried SUNSHINE app, but it prompted me that "team is still working on updates.
---------- Post added at 03:26 PM ---------- Previous post was at 03:20 PM ----------
Hi Expert,
Previously in my stock recovery, i can't update lollipop as it prompted me 'MOUNT SDCARD /0 exception. Now i updated my OTA there was a status bar progressing. let me check.
I UNLOCKED and rooted my phone myself. My security is S-ON.
---------- Post added at 03:53 PM ---------- Previous post was at 03:26 PM ----------
Hi CKPV5,
My software is updated to
5.0.1 and HTC sense version is 6.0
Software Number:4.16.709.9
Please let me know whether it is Lollipop version.
My root privilege has been revoked on this update. Can i again update to ROOT.
Pls advise
bharaka said:
Hi CKPV5,
My software is updated to
5.0.1 and HTC sense version is 6.0
Software Number:4.16.709.9
Please let me know whether it is Lollipop version.
My root privilege has been revoked on this update. Can i again update to ROOT.
Pls advise
Click to expand...
Click to collapse
Mentioned many times 4.16.709.9 is lollipop ....
Reflash TWRP then flash SuperSu again to root.
Wait ... you said you want to install custom ROM ... then you don't need to flash SuperSu because custom ROMs are pre-rooted. Just pick one of them and install.
To help you to install "which recovery" already done .. so now it's time for you to enjoy your lollipop and whatever ROM that you like .. I won't get involve when it comes to custom ROM.
Thank you very much
Hi CKPV5,
I have one clarification. Please clarify.
1. Earlier my phone was UNLOCKED and ROOTED. MY SECURITY IS ON.
2. During OTA update, it got failed and indicated "Mount error /0 in SD card".
3. I flashed TWRP 8.x.... and now reverted to STOCK recovery that you prescribed and I updated the same.
4. My OTA update worked finally and my Firmware got updated to Lollipop.
Please share and let me know how it got failed earlier and now got succeeded with same STOCK recovery 3.28.709.6.
Kind Regards,
-Bharathi
I really hope someone can help me!!
Tried to flash new boot loader version to 3.19 to install CM12 through fastboot. Had an error at the end saying it failed. I then tried to go back to stock and update with OTA's to get the new boot loader version so I could flash CM12, but that didn't work either. Rebooted phone and it was dead. Tried to do a wipe and restore nandroid backup. Said it couldn't read file. When I had my 64gb SD Card in the phone the Radio and Open DSP come up as invalid on the boot loader screen. But if I put in a 1 gb SD card or no SD card the Radio and Open DSP are OK. Put in a 1gb SD card with the CM11 zip and tried to flash in CWM recovery, looked to install OK, but still gets stuck in boot loop. Have tried re-flashing a few times and no luck.
Bootloader unlocked, s-on,
Can you provide your
fastboot getvar
Here's a thread that could help you out
http://forum.xda-developers.com/showthread.php?t=2735235
jball said:
Can you provide your
fastboot getvar
Here's a thread that could help you out
http://forum.xda-developers.com/showthread.php?t=2735235
Click to expand...
Click to collapse
C:\fastboot_adb\fastboot_adb>fastboot getvar all
< waiting for device >
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.16.0.0000
(bootloader) version-baseband: 1.15.2133156.UA13G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 1.54.206.5
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: SH44SWM10183
(bootloader) imei: 358714054617026
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B10000
(bootloader) cidnum: O2___001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: ab0efa49
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.085s
Find the ruu exe. For your version main: 1.54.206.5 and relock your bootlooader so you can run the exe .if you could find the right exe that matches or use the WWE exe .
jball said:
Find the ruu exe. For your version main: 1.54.206.5 and relock your bootlooader so you can run the exe .if you could find the right exe that matches or use the WWE exe .
Click to expand...
Click to collapse
I can't find the RUU for 1.54.206.5 anywhere. I've found nandroid backups, images, etc for 1.54.206.5 but they won't flash (I my be doing something wrong). Any other ideas? Can I run a newer RUU?
I got the WEE 1.54.1540.10 BrightstarUS RUU but it said it wasn't compatible? My CID is o2___001. Do I need to try find something that matches that as well as 1.54.206.5?
pats87 said:
I can't find the RUU for 1.54.206.5 anywhere. I've found nandroid backups, images, etc for 1.54.206.5 but they won't flash (I my be doing something wrong). Any other ideas? Can I run a newer RUU?
I got the WEE 1.54.1540.10 BrightstarUS RUU but it said it wasn't compatible? My CID is o2___001. Do I need to try find something that matches that as well as 1.54.206.5?
Click to expand...
Click to collapse
Is the device functional
jball said:
Is the device functional
Click to expand...
Click to collapse
What do you mean by functional? I can flash different recoveries, boot into them and boot into bootloader and RUU, and I can lock and unlock bootloader.
Should I be able to flash any WWE version?
are U s-on or s-off of u are s-off u can change your cid and mid number and flash developer edition ruu
Sorry
I forgot you said it does not boot to the system
---------- Post added at 11:12 AM ---------- Previous post was at 11:10 AM ----------
Neynge said:
are U s-on or s-off of u are s-off u can change your cid and mid number and flash developer edition ruu
Click to expand...
Click to collapse
He's S-ON
Hey Community,
My colleague gave me his cell phone (HTC One M8), because I have previously worked with cfws and was flashing phones (but this was at time of Gingerbread on LGP920).
That's why I'm not a novice but I'm not familiar with today's technology.
He updated his HTC (it isn't rooted) and get stuck at bootscreen. Now he can't do anything. Recovery & Hard-Reset nothing works for him. I just get into the fastboot mode.
Can you tell me what can I do next?
What's the details on fastboot/bootloader ?
Okey it's unlocked....
Software status: Official
M8_UL PVT SHIP S-ON
HBOOT-3.19.0.0000
RADIO-1.22.21331147A1.29G
OpenDSP-v46.2.2-00564-M8974_F0.0811
OS-3.28.401.9
eMMC-boot 2048 M
So it's still 4.4.4 firmware and not upgraded to lollipop yet.
Since it is unlocked, install TWRP 2.8.4.0
Then download the TWRP nandroid backup for 3.28.401.9 and stock recovery from here :
http://forum.xda-developers.com/showpost.php?p=56979449&postcount=2960
Restore that nandroid, then fastboot flash the stock recovery
then reboot and do OTA checking and let the system install the OTA.
ckpv5 said:
So it's still 4.4.4 firmware and not upgraded to lollipop yet.
Since it is unlocked, install TWRP 2.8.4.0
Then download the TWRP nandroid backup for 3.28.401.9 and stock recovery from here :
http://forum.xda-developers.com/showpost.php?p=56979449&postcount=2960
Restore that nandroid, then fastboot flash the stock recovery
then reboot and do OTA checking and let the system install the OTA.
Click to expand...
Click to collapse
But the Problem is... How I get TWRP on my device. I cant't start it at the moment.
You don't need to be on its desktop, only on bootloader (as you wrote the bootloader details)
Then flash the TWRP recovery in fastboot mode (connect to PC when on bootloader where you see the word fastboot usb in red on bootloader)
Run command fastboot flash recovery recovery.img (of course you need to have fastboot/adb already installed on PC)
ckpv5 said:
You don't need to be on its desktop, only on bootloader (as you wrote the bootloader details)
Then flash the TWRP recovery in fastboot mode (connect to PC when on bootloader where you see the word fastboot usb in red on bootloader)
Run command fastboot flash recovery recovery.img (of course you need to have fastboot/adb already installed on PC)
Click to expand...
Click to collapse
Thank You! I will try it later at home... Is it possible that the S-On creating problems with your methode?
Hi,
I am unfortunately in a very similar situation on an update I started that I must've made some mistakes on.
I'm trying to go from 4.4.3 (with Viper ROM 2.5.0), to 4.4.4 (with Viper ROM 3.2.1).
Have done a couple ROMs on 4.4.2 (even to a GPE edition and back to Sense 4.4.2 with Viper 1.8), then finally onto the 4.4.3 with Viper 2.5.0.... so I'm somewhat OK with understanding & following instructions (til now).
Tried a few things in fastboot, but always seem to get hung trying to load from a reboot....can only boot into fastboot (hangs trying to boot the 4.4.3 OS it seems, I've waited up to 45 minutes at the Green HTC Logo and 'powered by Android' screen.
Just tried the fastboot flash recovery openrecovery-twrp-2.8.4.0-m8.img and I'm again waiting ~30 minutes now....
The info from my fastboot getvar all:
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.22.21331147A1.29G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.28.401.9
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: --------------
(bootloader) imei: --------------
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B12000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: df77f8b7
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
Any help on where to go from here?
EDIT: Oh....I was eventually trying to go to 5.0 Lollipop, but another post in the Viper ROM thread said to go from 4.4.3, to 4.4.4, and then to 5.0. So I didn't start a new thread....
swedax94 said:
Thank You! I will try it later at home... Is it possible that the S-On creating problems with your methode?
Click to expand...
Click to collapse
It doesn't matter S-On or S-Off ... as long as the bootloader is UNLOCKED
---------- Post added at 01:56 AM ---------- Previous post was at 01:48 AM ----------
sttw1fa said:
Any help on where to go from here?
EDIT: Oh....I was eventually trying to go to 5.0 Lollipop, but another post in the Viper ROM thread said to go from 4.4.3, to 4.4.4, and then to 5.0. So I didn't start a new thread....
Click to expand...
Click to collapse
I'm not familiar with Viper ROM as I never use one so not sure their ROM's requirement.
But, your fastboot getvar all suggests that you flashed EU WWE 4.4.4 firmware without change of MID.
So what actually you want to do ? If it just to update to lollipop firmware then use maybe 5.0.1 based Viper, you only need to flash a modified lollipop firmware which include your MID 0P6B12000. Or easier, change your MID to EU 0P6B10000 then you can flashed the latest EU firmware 4.16.401.10
Or you want to get back to your original device region stock ROM and do update to lollipop if there is one available ?
Now when I'm starting the recovery there is a message ...this build is for devlopment purpose only....
swedax94 said:
Now when I'm starting the recovery there is a message ...this build is for devlopment purpose only....
Click to expand...
Click to collapse
That's normal because you have a custom recovery.
Can you get into recovery ? In there you can mount MTP then you can transfer the downloaded Nandroid backup (which you already extracted on PC) to your TWRP backup folder.
Make a backup of say boot only .. then you can see where the TWRP backup path so you can copy the extracted nandroid to the right location which look something like this
TWRP/BACKUPS/DeviceSerialNo/BackupFolder
sttw1fa said:
Hi,
I am unfortunately in a very similar situation on an update I started that I must've made some mistakes on.
I'm trying to go from 4.4.3 (with Viper ROM 2.5.0), to 4.4.4 (with Viper ROM 3.2.1).
Click to expand...
Click to collapse
This is not even remotely similar to the OP's issue. He is trying to boot after a failed OTA; not a custom ROM.
sttw1fa said:
Hi,
EDIT: Oh....I was eventually trying to go to 5.0 Lollipop, but another post in the Viper ROM thread said to go from 4.4.3, to 4.4.4, and then to 5.0. So I didn't start a new thread....
Click to expand...
Click to collapse
Not sure, but the incremental updating probably refers to the firmware (or possibly OTA to update the firmware), not the ROM.
---------- Post added at 01:14 PM ---------- Previous post was at 01:12 PM ----------
swedax94 said:
Okey it's unlocked....
Click to expand...
Click to collapse
What happens when you choose recovery from bootloader?
ckpv5 said:
That's normal because you have a custom recovery.
Can you get into recovery ?
Click to expand...
Click to collapse
redpoint73 said:
What happens when you choose recovery from bootloader?
Click to expand...
Click to collapse
No, it seems to stuck at entering recovery and after 2 minutes it goes to normal bootscreen.
swedax94 said:
No, it seems to stuck at entering recovery and after 2 minutes it goes to normal bootscreen.
Click to expand...
Click to collapse
Try run command
fastboot erase cache
fastboot reboot-bootloader
then try again to enter recovery
I need to sign-off now ... it's almost 2.30 am here.
I'll check tomorrow on your progress.
Maybe someone else will be able to help you in my absent.. good luck
ckpv5 said:
Try run command
fastboot erase cache
fastboot reboot-bootloader
then try again to enter recovery
Click to expand...
Click to collapse
This.
And if that doesn't work, flash recovery again.
and last thing from me for tonight ... if you don't mind losing everything on internal storage, you can use RUU zip.
See : http://forum.xda-developers.com/showpost.php?p=58504115&postcount=8
But you need to relock bootloader to use the RUU zip because your device is S-On
command to relock : fastboot oem lock
you can use either 3.28.401.9 or 4.16.401.10
redpoint73 said:
This is not even remotely similar to the OP's issue. He is trying to boot after a failed OTA; not a custom ROM.
Click to expand...
Click to collapse
Sorry for the mix up. Didn't mean to derail. At the time when I typed, the only accessible option of booting was into Fastboot (recovery option failed to boot, etc.), so I thought it was similar with all the searching I was doing.
Found a solution for me via the TWRP website. All good for me atm on 4.4.4 FW with Viper ROM 3.2.1. Headed to 5.0 FW with Viper later this evening.
redpoint73 said:
This is not even remotely similar to the OP's issue. He is trying to boot after a failed OTA; not a custom ROM.
Not sure, but the incremental updating probably refers to the firmware (or possibly OTA to update the firmware), not the ROM.
---------- Post added at 01:14 PM ---------- Previous post was at 01:12 PM ----------
What happens when you choose recovery from bootloader?
Click to expand...
Click to collapse
sttw1fa said:
Sorry for the mix up. Didn't mean to derail. At the time when I typed, the only accessible option of booting was into Fastboot (recovery option failed to boot, etc.), so I thought it was similar with all the searching I was doing.
Found a solution for me via the TWRP website. All good for me atm on 4.4.4 FW with Viper ROM 3.2.1. Headed to 5.0 FW with Viper later this evening.
Click to expand...
Click to collapse
Thank you! Problem solved. For People with same Problems i had done these steps:
1. Unlock your Bootloader
2. Load adb/fastboot (if you're to lazy to install this all, like me, use the version from the video https://www.youtube.com/watch?v=5xVl2dBTnmI)
3. Then load the latest Version of TRWP and flash it with fastboot
4. Download the right nandroid backup here http://forum.xda-developers.com/showpost.php?p=56979449&postcount=2960
5. Start Recovery on your Device and Make backup of boot (to see were the right place is to put in the nandroid)
6. Start Backup from the nandroid
7. Finish
THANKS FOR ckpv5!!!!! YOU HELPED ME SO MUCH!!!
ps. I reflashed TRWP then it worked sry for my bad english
Red triangle after attempt to restore to stock
HI THIS IS MY FIRST POSTING ON THIS SITE, HAVE AN HTC ONE M8 FROM EE UK , I ROOTED IT AND INSTALLED TWRP RECOVERY. WHEN LOLLIPOP CAME OUT I DECIDE TO RESTORE TO STOCK AND INSTALL UPDATE. I THINK I MUST HAVE INSTALLED THE WRONG FIRMWARE . SOMEHOW I STILL HAVE ROOT ACCESS EVEN THOUGH I'M SUPPOSED TO BE IN STOCK( ), BUT I CAN'T BOOT TO RECOVERY THE RED TRIANGLE SHOWS UP. I'M SURE I'VE MESSED UP THE PROCESS SOMEWHERE.
PLEASE I WOULD LIKE TO RESTORE MY PHONE TO STOCK AND INSTALL THE LOLLIPOP UPDATE, CAN YOU HELP?. IM ALSO HAVING CALL SIGNAL ISSUES, COMPLAINTS OF MY PHONE NOT BEING AVAILABLE EVEN THOUGH ITS ON.
No OS Number
M8_UL PVT SHIP S-ON
HBOOT-3.19.0.0000
RADIO-1.22.21331147A1.29G
OpenDSP-v46.2.2-00564-M8974_F0.0811
OS-
eMMC-boot 2048 M
C:\fastboot_adb>fastboot getvar all (bootloader) version: 0.5 (bootloader) version-bootloader: 3.19.0.0000 (bootloader) version-baseband: 1.22.21331147A1.29G (bootloader) version-cpld: None (bootloader) version-microp: None (bootloader) version-main: (bootloader) version-misc: PVT SHIP S-ON (bootloader) serial no: (bootloader) imei: (bootloader) imei2: Not Support (bootloader) meid: 00000000000000 (bootloader) product: m8_ul (bootloader) platform: hTCBmsm8974 (bootloader) modelid: 0P6B10000 (bootloader) cidnum: ORANG001 (bootloader) battery-status: good (bootloader) battery-voltage: 0mV (bootloader) partition-layout: Generic (bootloader) security: on (bootloader) build-mode: SHIP (bootloader) boot-mode: FASTBOOT (bootloader) commitno-bootloader: 4c3fbd70 (bootloader) hbootpreupdate: 11 (bootloader) gencheckpt: 0 all: Done! finished. total time: 0.039s
Axdel said:
HI THIS IS MY FIRST POSTING ON THIS SITE, HAVE AN HTC ONE M8 FROM EE UK , I ROOTED IT AND INSTALLED TWRP RECOVERY. WHEN LOLLIPOP CAME OUT I DECIDE TO RESTORE TO STOCK AND INSTALL UPDATE. I THINK I MUST HAVE INSTALLED THE WRONG FIRMWARE . SOMEHOW I STILL HAVE ROOT ACCESS EVEN THOUGH I'M SUPPOSED TO BE IN STOCK( ), BUT I CAN'T BOOT TO RECOVERY THE RED TRIANGLE SHOWS UP. I'M SURE I'VE MESSED UP THE PROCESS SOMEWHERE.
PLEASE I WOULD LIKE TO RESTORE MY PHONE TO STOCK AND INSTALL THE LOLLIPOP UPDATE, CAN YOU HELP?. IM ALSO HAVING CALL SIGNAL ISSUES, COMPLAINTS OF MY PHONE NOT BEING AVAILABLE EVEN THOUGH ITS ON.
No OS Number
M8_UL PVT SHIP S-ON
HBOOT-3.19.0.0000
RADIO-1.22.21331147A1.29G
OpenDSP-v46.2.2-00564-M8974_F0.0811
OS-
eMMC-boot 2048 M
C:\fastboot_adb>fastboot getvar all (bootloader) version: 0.5 (bootloader) version-bootloader: 3.19.0.0000 (bootloader) version-baseband: 1.22.21331147A1.29G (bootloader) version-cpld: None (bootloader) version-microp: None (bootloader) version-main: (bootloader) version-misc: PVT SHIP S-ON (bootloader) serial no: (bootloader) imei: (bootloader) imei2: Not Support (bootloader) meid: 00000000000000 (bootloader) product: m8_ul (bootloader) platform: hTCBmsm8974 (bootloader) modelid: 0P6B10000 (bootloader) cidnum: ORANG001 (bootloader) battery-status: good (bootloader) battery-voltage: 0mV (bootloader) partition-layout: Generic (bootloader) security: on (bootloader) build-mode: SHIP (bootloader) boot-mode: FASTBOOT (bootloader) commitno-bootloader: 4c3fbd70 (bootloader) hbootpreupdate: 11 (bootloader) gencheckpt: 0 all: Done! finished. total time: 0.039s
Click to expand...
Click to collapse
That red triangle means you have the stock recovery.
Hello
Since i flashed the gpe ruu, i cant get back to sense.
I tried almost everything. I tried 3 different ruu.exe's, 2 different ruu.zip's and dozens of firmwares. (old and new ones, international and devEd's)
My Bootloader is unlocked, i have s-off and supercid.
(I tried everything with a relocked bootloader, too!)
I followed this guide right here. (And a good hand full of other guides, here on xda)
Currently i have cm13 installed (without gapps!! -.- because /system is too small), but i really want sense back tho
I downloaded 3 different sense based custom roms and tried them all. But twrp is unable to flash them, due to the changed /system partition size. (i tried twrp 2.8.7.0 AND 3.0.0-1)
For those of you who are able to speak or read german, I have a different thread in a german forum.
I appreciate any help!
Thanks
What specific RUUs (file name) and firmwares (version numbers) did you try?
Do fastboot getvar all, and post the results (delete IMEI and serial number before posting).
Firmware's:
1.54.401.5-W_Splash.zip
M8_4.16.401.13_WWE_TWRP2870.zip
M8_6.12.401.4_WWE_FullStock.zip
M8_6.12.401.4_WWE_TWRP2870.zip
M8_6.12.1540.4_DevEd_FullStock.zip
RUU's:
RUU_M8_UL_L50_SENSE60_MR_HTC_Europe_4.16.401.10_Radio_1.25.214500021.06G_20.68.4196t.01_F_release_417003_signed.exe
RUU_3.28.401.9_M8_WWE_Stock.exe
0P6BIMG_M8_UL_M60_SENSE70_MR_HTC_Europe_6.12.401.4_Radio_1.29.214500021.12G_20.72.4196t.01_release_464360_signed.zip
0P6BIMG_M8_UL_L50_SENSE60_MR_HTC_Europe_4.16.401.10_Radio_1.25.214500021.06G_20.68.4196t.01_F_release_417809_signed.zip
fastboot getvar all: (i restored an old cm13 backup. i dont know why there is no version-main)
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.12G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: ----
(bootloader) imei: ----
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B17000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 76df2b54
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
crruell said:
(bootloader) modelid: 0P6B17000
Click to expand...
Click to collapse
There is your problem .. you need to change it to 0P6B10000 then flash the firmware.zip then install RUU.
See this on how to change it : http://forum.xda-developers.com/showthread.php?t=2708581
ckpv5 said:
There is your problem .. you need to change it to 0P6B10000 then flash the firmware.zip then install RUU.
See this on how to change it : http://forum.xda-developers.com/showthread.php?t=2708581
Click to expand...
Click to collapse
Oh my god..
Thank you mate! I will try this, when im back home
crruell said:
fastboot getvar all: (i restored an old cm13 backup. i dont know why there is no version-main)
Click to expand...
Click to collapse
Known TWRP bug, usually happens due to an older version TWRP being used at some point in the past.
Once you flash a firmware successfully, that firmware's version number will be properly shown as main version again.
Hm.
i still cant flash the ruu.
ruu.exe is still giving me errors and the .zip in hboot still says, that the /system partition is too small.
(i also tried the original mid [t-mobile])
solution:
ruu.exe & ruu zip wont work for me.
i tried flashing the firmware & latest twrp and then restoring 6.12.401.4-twrp backup.
and..
it actually worked.
(sorry for double post. i didnt mean to :s)
crruell said:
solution:
ruu.exe & ruu zip wont work for me.
i tried flashing the firmware & latest twrp and then restoring 6.12.401.4-twrp backup.
and..
it actually worked.
(sorry for double post. i didnt mean to :s)
Click to expand...
Click to collapse
As I said earlier.. flash firmware.zip first to change partition size then only you can install RUU.
Restoring a backup after firmware.zip is as same as install RUU after firmware.zip is flashed.
And to install RUU zip, you need to use htc_fastboot.exe
Htc one m8
fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.12G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.12.401.4
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: HT46PWM03644
(bootloader) imei: 3578710********
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B10000
(bootloader) cidnum: HTC__102
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 76df2b54
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.158s
Is there a solution without s-off
Tried Stock rom:
RUU_M8_UL_L50_SENSE60_MR_BrightstarUS_WWE_4.16.154 0.8_Radio_1.24.21331147A1.09G_20.68.4196.01_F_rele ase_411207_signed.exe
RUU_M8_UL_L50_SENSE60_MR_HTC_Europe_4.16.401.10_Ra dio_1.25.214500021.06G_20.68.4196t.01_F_release_41 7003_signed.exe
RUU_M8_UL_M60_SENSE70_MR_BrightstarUS_WWE_6.12.154 0.4.exe
with bootloader locked/unlocked state;
with s-on:
Failed
Tried zip
0P6BIMG_M8_UL_M60_SENSE70_MR_HTC_Europe_6.12.401.4 _Radio_1.29.214500021.12G_20.72.4196t.01_release_4 64360_signed.zip
Failed
Tried nandroid backup
M8_UL_TWRP_Nandroid_6.12.401.4.zip
succefully flashed backup but stuck on htc logo
Failed
Please help
What is the problem? Is it not booting into the ROM?
when there was boot.the phone at the startup gave (unfortunately------- has stopped)error and also no back key home key visible.
wiped the device. it was all same.
tried RUU it was the same
unlocked the boot loader
and flashed
stock recovery
twrp recovery
then tried nandroid backup restore
the restore was succefull but the phone wont reach startup (tried 1Hour max)
one peculiar thing i notice.earlier when it was booting to startup i was unable to copy anything to internal or external memory as it would say device not ready or disconnected.but i was able to browse the folders.
My opinion partition problem.Need others help to sort out
Note all the files i have mentioned is checked with md5
My comments below in red font:
raffazila said:
Tried Stock rom:
RUU_M8_UL_L50_SENSE60_MR_BrightstarUS_WWE_4.16.154 0.8_Radio_1.24.21331147A1.09G_20.68.4196.01_F_rele ase_411207_signed.exe
RUU_M8_UL_L50_SENSE60_MR_HTC_Europe_4.16.401.10_Ra dio_1.25.214500021.06G_20.68.4196t.01_F_release_41 7003_signed.exe
RUU_M8_UL_M60_SENSE70_MR_BrightstarUS_WWE_6.12.154 0.4.exe
None of these will ever work on your device, in the s-on configuration. The RUUs containing "BrightstarUS" are for the US Developer's Edition. They won't run on your phone, as they will fail CID and MID checks (your device has CID and MID - can't change these with s-on).
The one labeled "Europe" is for an older version (Lollipop) than what is installed on the phone (Marshmallow). This will fail version check. By definition, you can't "downgrade" by RUU with s-on
with bootloader locked/unlocked state;
with s-on:
Failed
with s-on, its absolutely mandatory to have a locked or relocked bootloader to flash RUU. Unlocked bootloader will make it fail
Tried zip
0P6BIMG_M8_UL_M60_SENSE70_MR_HTC_Europe_6.12.401.4 _Radio_1.29.214500021.12G_20.72.4196t.01_release_4 64360_signed.zip
Failed
This is the correct RUU for your version, and should run with s-on. Saying it "Failed" with no other info, is not enough. Were their any error messages, other outputs, etc.? What commands did you use to run it? Were you in fastbootRUU mode?
I would suggest trying to run this again, with the bootloader RELOCKED, and you also need to use htc_fastboot, as the "generic" fastboot will not work with RUU.
Click to expand...
Click to collapse
Firstly it is good someone with good knowledge is answering my doubts.
Secondly i want to tell you something which i noticed in most of the forum is irrelevant posts.I want to avoid those kind of post.
Finaly to say you have found the nearest problem which i was thinking too.
I will check and post.
@redpoint73 Problem soilved.Silly mistake.Thanks.
raffazila said:
Secondly i want to tell you something which i noticed in most of the forum is irrelevant posts.I want to avoid those kind of post.
Click to expand...
Click to collapse
I can't tell what you are referring too, as the statement is really vague. Can you give more details?
---------- Post added at 09:31 AM ---------- Previous post was at 09:28 AM ----------
raffazila said:
Problem soilved.Silly mistake.Thanks.
Click to expand...
Click to collapse
Its best if you posted the solution, and what the mistake was. Useful for those helping (to see whether we sent you on the right path), as well as anyone else reading which may have the same or similar issue.
No mistake is that silly when it comes to these devices. Its often just specific knowledge that was missing, or a detail you didn't catch before (which is an honest mistake, either way).