[TOOL] MOTO G xt1068 Andoid L [ 5.0 ] updater + Rooter - G 2014 Android Development

This tutorial is for those who can't wait for the official OTA and already unlocked their boot loader. This method actually fakes your firmware and enables support for the OTA as other countries like US has already released the Lollipop update for Moto G. I've updated my Moto G 2nd Gen to lollipop using this method.
Disclaimer
Unlocking boot loader voids your warranty and wipes everything from your internal memory. It's entirely possible to lose your phone by following this procedure. So I will not be held responsible for the possible outcomes.
Pre-requisites
*You must have an unlocked boot loader.
*This method is tried successfully on Moto G variants XT1068 (dual sim) and XT1069. Don’t try this on other variants.
*Backup your important data before proceeding.
*Download and install Motorola USB drivers from Here
Steps
Download the Tool [This is the minimal size] : Direct Download: (Fast!)bit.ly/moto55l OR Here or http://bit.ly/motoL5 oR NEW LINK http://bit.ly/moto5L OR http://bit.ly/MotoLL5
Extract it to a folder
Open Command Prompt by holding shift then right clicking in folder you extracted
Now run
Code:
updater.bat
Copy the file
Code:
update-nofsg-working.zip
to your internal storage.
Rename the file "CWM_Touch_Titan_V2.img " in the folder (on your PC) to "CWM_Touch_Titan_V2_2.img ".
Again boot your phone in boot loader mode and connect it to the computer. Open command window in the folder and run recovery.bat
In the bootloader menu, choose “Recovery” option. You will now enter into the Philz recovery. If it fails, repeat step 9.
In Philz recovery, choose install zip and select “update_nofsg.zip” file which you have copied in step 7.
Let it flash. It will take around 10 minutes to complete the flashing. After finishing, reboot the system and you’re done!
After installing "update_nofsg.zip" in Recovery there comes up the question if device should be rooted.
Tap on NO, reboot to Android L.
Rooting
Boot takes 10 minutes at least after rooting! (One time)
Make sure you have atleast Booted once in Andoid L
Copy the file
Code:
BETA-SuperSU-v2.19.zip
To your internal storage.
Reboot to fastboot then run
Code:
root.bat
It will reboot the phone.
Go to bootloader again and select Recovery
Intall
Code:
BETA-SuperSU-v2.19.zip
Reboot .. Rooted! (reboot will be ALOT longer than normal) wait at least 11/2 minutes, don’t be fooled by the time, I have been successful since the first attempt, but didn’t wait long enuff for the bootloader warning screen, and thought the device was locked up, and I would reflash KK and start over again, I done this at least five times, trying different procedures, trying to figure it out, but in reality, had it right the very first try..
If you are not rooted then again go to bootloader and run
Code:
root.bat
but don't flash SU again
Screenshots
Coming soon!
Confirmed Working Both Sims!
XDA:DevDB Information
MOTO G XT1068 Andoid L [ 5.0 ] updater + Rooter, Tool/Utility for the Moto G 2014
Contributors
Ashesh1708
Version Information
Status: Stable
Current Stable Version: 1
Stable Release Date: 2014-12-07
Created 2014-12-07
Last Updated 2014-12-07

two same threads????/ why????

Mirror The link please
DB having hiccups

fifa2151 said:
Mirror The link please
DB having hiccups
Click to expand...
Click to collapse
Thanks, Links updated!

Phone info
Ashesh1708 said:
This tutorial is for those who can't wait for the official OTA and already unlocked their boot loader. This method actually fakes your firmware and enables support for the OTA as other countries like US has already released the Lollipop update for Moto G. I've updated my Moto G 2nd Gen to lollipop using this method.
Disclaimer
Unlocking boot loader voids your warranty and wipes everything from your internal memory. It's entirely possible to lose your phone by following this procedure. So I will not be held responsible for the possible outcomes.
Pre-requisites
*You must have an unlocked boot loader.
*This method is tried successfully on Moto G variants XT1068 (dual sim) and XT1069. Don’t try this on other variants.
*Backup your important data before proceeding.
*Download and install Motorola USB drivers from Here
Steps
Download the Tool [This is the minimal size] : Here OR Mirror
Extract it to a folder
Open Command Prompt by holding shift then right clicking in folder you extracted
Now run
Code:
updater.bat
Copy the file
Code:
update-nofsg-working.zip
to your internal storage.
Again boot your phone in boot loader mode and connect it to the computer. Open command window in the folder and run recovery.bat
In the bootloader menu, choose “Recovery” option. You will now enter into the Philz recovery. If it fails, repeat step 9.
In Philz recovery, choose install zip and select “update_nofsg.zip” file which you have copied in step 7.
Let it flash. It will take around 10 minutes to complete the flashing. After finishing, reboot the system and you’re done!
Rooting
Make sure you have atleast Booted once in Andoid L
Copy the file
Code:
BETA-SuperSU-v2.19.zip
To your internal storage.
Reboot to fastboot then run
Code:
root.bat
It will reboot the phone.
Go to bootloader again and select Recovery
Intall
Code:
BETA-SuperSU-v2.19.zip
Reboot .. Rooted!
If you are not rooted then again go to bootloader and run
Code:
root.bat
but don't flash SU again
XDA:DevDB Information
MOTO G XT1068 Andoid L [ 5.0 ] updater + Rooter, Tool/Utility for the Moto G 2014
Contributors
Ashesh1708
Version Information
Status: Stable
Current Stable Version: 1
Stable Release Date: 2014-12-07
Created 2014-12-07
Last Updated 2014-12-06
Click to expand...
Click to collapse
Thanks for the work!
Phone screenshot of information you can give?
Thank you!

Noobie question:
After following the steps here, do we just update via OTA to Lollipop?
Also, can you confirm both the SIM cards work?

system info
What is the full version System?
Thank you!

Sorry but i dont understand properly....i have to download any firmware or just i receive it OTA
Sent from my XT1068 using XDA Premium 4 mobile app

Solution
amritmalviya said:
Sorry but i dont understand properly....i have to download any firmware or just i receive it OTA
Sent from my XT1068 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
You have to download my tool as a zip that will contain Android L rom then running the bat files accordingly will automatically install Android L on your XT1068

But it is just 0kb and also unable to download plz help
Sent from my XT1068 using XDA Premium 4 mobile app

I got through the steps until just before recovery.bat
I cannot get into recovery (Philz)
I get this error:
C:\Users\Windows\Downloads\Moto G Tool>recovery.bat
C:\Users\Windows\Downloads\Moto G Tool>mfastboot.exe flash recovery CWM_Touch_T
itan_V2_2.img
target max-sparse-size: 256MB
error: cannot load 'CWM_Touch_Titan_V2_2.img': No error

premaru said:
Noobie question:
After following the steps here, do we just update via OTA to Lollipop?
Also, can you confirm both the SIM cards work?
Click to expand...
Click to collapse
After you follow these steps you will automatically have AndroidL installed
This happens after you flash `update-nofsg-working.zip` In recovery

No screenshots
Screenshots do not work. ((

Ashesh1708 said:
After you follow these steps you will automatically have AndroidL installed
This happens after you flash `update-nofsg-working.zip` In recovery
Click to expand...
Click to collapse
Can i flash it directly on xt1068 or i have to download another firmware
Sent from my XT1068 using XDA Premium 4 mobile app
---------- Post added at 07:05 PM ---------- Previous post was at 07:02 PM ----------
Drop box is giving error....
Sent from my XT1068 using XDA Premium 4 mobile app

I cannot get into Philz recovery. Please help.
Also, the device is only showing one SIM now.
Please help me !

This Android L update is the one ported from XT1064 or the one for XT1068 got from the TWRP backup of general section?
Thanks

How do I restore it back to stock please???

Help i am unable to download tool
Sent from my XT1068 using XDA Premium 4 mobile app

system versyon?
Ashesh1708 said:
This tutorial is for those who can't wait for the official OTA and already unlocked their boot loader. This method actually fakes your firmware and enables support for the OTA as other countries like US has already released the Lollipop update for Moto G. I've updated my Moto G 2nd Gen to lollipop using this method.
Disclaimer
Unlocking boot loader voids your warranty and wipes everything from your internal memory. It's entirely possible to lose your phone by following this procedure. So I will not be held responsible for the possible outcomes.
Pre-requisites
*You must have an unlocked boot loader.
*This method is tried successfully on Moto G variants XT1068 (dual sim) and XT1069. Don’t try this on other variants.
*Backup your important data before proceeding.
*Download and install Motorola USB drivers from Here
Steps
Download the Tool [This is the minimal size] : Here
Extract it to a folder
Open Command Prompt by holding shift then right clicking in folder you extracted
Now run
Code:
updater.bat
Copy the file
Code:
update-nofsg-working.zip
to your internal storage.
Again boot your phone in boot loader mode and connect it to the computer. Open command window in the folder and run recovery.bat
In the bootloader menu, choose “Recovery” option. You will now enter into the Philz recovery. If it fails, repeat step 9.
In Philz recovery, choose install zip and select “update_nofsg.zip” file which you have copied in step 7.
Let it flash. It will take around 10 minutes to complete the flashing. After finishing, reboot the system and you’re done!
Rooting
Make sure you have atleast Booted once in Andoid L
Copy the file
Code:
BETA-SuperSU-v2.19.zip
To your internal storage.
Reboot to fastboot then run
Code:
root.bat
It will reboot the phone.
Go to bootloader again and select Recovery
Intall
Code:
BETA-SuperSU-v2.19.zip
Reboot .. Rooted!
If you are not rooted then again go to bootloader and run
Code:
root.bat
but don't flash SU again
Screenshots
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Confirmed Working Both Sims!
XDA:DevDB Information
MOTO G XT1068 Andoid L [ 5.0 ] updater + Rooter, Tool/Utility for the Moto G 2014
Contributors
Ashesh1708
Version Information
Status: Stable
Current Stable Version: 1
Stable Release Date: 2014-12-07
Created 2014-12-07
Last Updated 2014-12-07
Click to expand...
Click to collapse
This version of the system?

OP
It would be nicer if you respond to questions, I'm here with a broken phone?
One more question:
****
In the bootloader menu, choose “Recovery” option. You will now enter into the Philz recovery. If it fails, repeat step 9.
****
Are you sure it's step 9?

Related

[Guide] How To Install / Flash Custom Roms Step by Step | Noobs Easy Way | Xperia S

Complete Beginners Guide To Flash Custom ROM on Xperia S | 2011 Devices
This Guide Is Made Easier To Understand The Basics To Install / Flash Custom ROM (Specifically On Xperia Phones). You will not need to go to any annoying links and go on reading lengthy descriptions everything required is provided here. :victory:
Everything is Step By Step.
Just Follow Them And Everything Will Work Fine
Now Lets Get Down To Business.
​
This Tutorial is Specially For
For Complete Beginners
For Newcomers to Android
For Those Who Want To Learn Flashing ROM Easy Way
People who did not had any encounters with Programming
Click to expand...
Click to collapse
Thanks To All The Senior Developers For Providing Us The Knowledge In Developing Modding And Flashing And Amazing Guides Through Out XDA Forum. Without You People This Guide Would Not Have Been Complete
Click to expand...
Click to collapse
This Guide Is Covered in Next 4 Posts With Every Step As Described Below.
NOTE : I Will Explain This Thread For Flashing Custom ROM Cyanogenmod 10 for Xperia S.
Link here---> https://sites.google.com/site/projectfreexperia/
You can download any Stable ROM The Procedure is Same For All.​
Step by Step Process Tree
Step 1. Rooting Xperia S​Step 2. Unlocking Bootloader​Step 3. Installing CWM Recovery​Step 4. Flashing A Custom ROM​Step 5. That's it! You will Have The Custom Rom Running.​
Click to expand...
Click to collapse
Step 1 : Rooting Your Xperia S
Step 1 : Rooting Your Xperia S
This is done by Using A Root Tool Provided by Our Senior Developer @Bin4ry. Please Press His Thanks Button For Helping Out For The Amazing TooL!
Just Download The Tool By Clicking Here : Root_with_Restore_by_Bin4ry_v30
For Xperia S 2.55 Firmware look in this thread: http://forum.xda-developers.com/show...php?p=39498268
But Don't Start Running The Tool Yet. Before That you need to Do A Couple Of Things, :angel:
Before Rooting What You Need?
1.) Install Your Phones Software Driver, ---> PC Companion Will Do The Job Just Connect The Phone And Check If It Detects!
2.) Activate USB Debugging, Setting ---> Developer Options
3.) Activate Unknown Sources, Setting ---> Security
4.) Connect Your Phone via USB
5.) Confirm That Your Device Is Connected Properly In Device Manager.
Only Then,
6.) Proceed With Rooting Tool Kit.
Click to expand...
Click to collapse
How To Use It?
1.) Download Attached File.
2.) Extract it Using Winrar
3.) Double click the RunMe.bat and follow instructions!
Xperia phones with "older" firmware = Normal mode
Sony Tablet and similar = Special mode
Xperia phones with JB Firmare = Mode 3 (Goroh_kun mode)
Click to expand...
Click to collapse
Complete Video Tutorial: https://www.youtube.com/watch?v=7EpkrCq1gfM
Just Follow The On Screen Instructions. (Its really easy like installing a game :laugh
After The Software Finishes Its Work! Your Phone Must BE Rooted By Now!
Step 2 : Unlocking Bootloader on Xperia S
Step 2 : Unlocking Bootloader on Xperia S
Procedure To Unlock Bootloader of Sony Xperia S LT26i :
1.) Installation of Fastboot USB Drivers (Xperia S)​2.) Unlocking Bootloader of Xperia S​
Click to expand...
Click to collapse
Now, We Will Unlock The Bootloader,
Why to Unlock Bootloader?
1.) You can flash custom ROMs/Kernels
2.) You don't need to worry if the new firmware can be rooted or not as with unlocked bootloader u can always ROOT Your device
[ Before We Begin Unlocking Bootloader ]
Get the IMEI code for ur device: type *#06# in phone dialer to find it out, note only the digits (no dashes)
Make Sure The Fastboot Drivers Are Installed.
Make sure u have a windows PC with USB cable to connect the phone
Power down ur phone and keeping the Volume Up button pressed connect the USB cable to PC this will trigger FASTBOOT mode and windows
Will start driver installation, extract the above package and point the driver install to that location (usb_driver) folder
Once drivers are installed just disconnect cable and power on device.
[ How to Unlock ] (Official Way)
Video Link ---> http://www.youtube.com/watch?v=LRH3pC7MhEA
For better understanding, I highly recommend you to watch the above video along with the instructions below:
1.) Download ‘Fastboot Drivers And Pacakges File For Xperia S’ file from → Here
2.) Extract the file you downloaded above on your PC. You’ll get the following three files:
drivers.zip
fastboot_with_Android_USB_file.zip
3.) Go to: http://unlockbootloader.sonymobile.com/ and read everything!
This will open a web page in your default browser. Scroll to the bottom of the Instructions on the page and you’ll see a link like “Continue”, click on it.
In the pop-up window click “Yes, I’m sure” and then in the next window click on both the checkboxes, and then click “I accept”.
4.) Now insert the details as per the instructions:
First 14 digits of your IMEI No. Do NOT enter the last digit (15th) in the box. To know your IMEI No. dial *#06# on your Xperia Arc.
Your Name
Your Email Address
Click Submit.
5.) You’ll get a KEY to unlock boot loader. Write it down somewhere you can remember, it will be used later.
6.) Switch off your phone.
7.) Now extract the “fastboot_with_Android_USB_file.zip” file you got in Step 2.2.
8.) Pick up your phone (it must be switched off) and hold the “Menu” button (the key at the bottom right of your phone), now while holding the “Menu” button connect your phone to your PC with an USB cable.
9.) Once connected — the LED light near the phone’s USB plug will turn blue. If it doesn’t — repeat the Step 8.
10.) Now to install the drivers do the following:
Extract the “drivers.zip” file you got in Step 2.1
Open “Device Manager” on your PC and look for “S1Boot Fastboot” under the head “Other devices”
Right-click on “S1Boot Fastboot” and select “Update Driver Software…”
Now select “Browse my computer for driver software” and select the folder where you’ve extracted all the three files you got in Step 2. Once done — click Ok.
Now click Next (Make sure you’ve ticked the “Include subfolders” checkbox).
If you see any Windows security warning box, don’t worry . Just select “Install this driver software anyway”
Wait for “Windows has successfully updated your driver software” message to appear on your screen. Now click Close.
11.) Open the “fastboot” folder from the file we extracted in Step 7.
12.) Now hold Shift and press mouse right click (Shift + Mouse Right Click) anywhere on the empty white space inside the “fastboot” folder. And then select “Open command window here” from the context menu.
13.) Now in the command prompt window type/paste the following:
fastboot.exe -i 0x0fce getvar version​
14.) It should return a value like “0.3”. This ensures that your device is correctly connected.
15.) Now type/paste the following line in the command prompt window:
fastboot.exe -i 0x0fce oem unlock 0xKEY​
IMPORTANT! Replace the word “KEY” from the above line with the KEY that you received in Step 5. Then Hit Enter.
Click to expand...
Click to collapse
16.) Now wait for the process to complete. Command prompt will show a “Finished” message when it will be completed.
17.)Once it’s done, disconnect the USB cable from your phone and switch it ON.
18.)Your phone’s boot loader should now be Unlocked.
(The above videos and some steps are for Xperia 2011 devices, but most the steps are same for Xperia S/P/U/Sola)
Click to expand...
Click to collapse
Step 3 : Installing ClockWorkMod Recovery With RoceoverX
Step 3 : Installing ClockWorkMod Recovery With RoceoverX
We Will Install Recovery Using RecoverX Software.
Download The Software from Here ----> RecoverX v1.6.8.0
You just have to select your device and the recovery, click "Install" and RecoverX does the rest !!! It's that simple!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 4 : Flashing ROM
Step 4 : Flashing ROM
Assuming you have already downloaded your required file, let’s proceed.
ROM Flashing
1.) Copy Paste update on Phone
Copy update- copy update-xxx-xxx-xxx.zip coresponding to your device to sdcard
Copy GAPPS. Download Link [Here]
2.) Flash CM kernel
Set USB Debugging On from Settings - Developer Options.
Connect the phone to the PC.
Click 1 - Click the Lightning icon.
Select 2 - Select the Fastboot Mode.
Click 3 - Click Ok.
Click 4 - Select Reboot Into Fastboot Via Adb and wait for the phone to go into fastboot mode. (Blue led).
Click 5 - Select Reboot Into Fastboot Via Fastboot and wait for the phone to go into fastboot mode. (Blue led).
Click 6 and 7 - Select the boot.img (Extract The boot.img file from zip)
Click 8 - Reboot phone. After reboot, the phone will be in recovery mode.​
Click to expand...
Click to collapse
3.) Boot into Recovery
While FXP logo is displayed (and lights are lit) press several times volume up to enter CWM (recovery)
4.) Flash ROM
To update main rom select
Install zip from sdcard
Choose zip from sdcard
Select your update (copied at step 2)
To flash gapps redo steps a-c and select gapps package
Use gapps version designed for your android version !!! Link ---> Here, Gapps
5.Wipe device
Whip Cache
Whip Dalvik Cache (Advanced Option)
Cache Partition
If after boot you experience ForceClose then is recomended to reboot to recovery and wipe device​
Click to expand...
Click to collapse
6.) Partition format
7.) Reboot and Enjoy :victory:
Troubleshooting
If you experience a bootloop (phone constantly reboots and reboots on the boot screen) or a soft brick (powering on the phone shows an orange triangle with a phone and computer), don’t be afraid. XDA to the rescue!
For a bootloop:
Hold The Power Button And Volume Up Button
If You Hold For 3 Seconds = Soft Reset = 1 Viberation
If You Hold For 10 Seconds = Hard Reset = 3 Viberations***
Power on the Phone Again, Keep pressing Volume Up Button
Your phone will boot into recovery.
Select “Wipe data/ Factory reset”. (Volume Up for going up and Volume down to go down)
After the reset is done, select “Reboot system now”.
The phone will reboot and you should be all fine.
***Do Not Try Hard Reset Untill And Unless The Phone is Facing Major Problems,
For a soft brick:
You probably flashed some faulty firmware or firmware not meant for your device.
The File You Downloaded Must Be Incomplete.
Download the correct firmware and flash again.
Feedback And Corrections
Please Feel Free To Message Me About Any Dead Links Or Corrections​
Feedbacks Are Welcome!​​
Which is the best way to flash / install a custom ROM / gapps ? With Flashtool or through TWRP / CWM ?
I'm now on stock ROM, Xperia ZL. Do i have to wipe / factory reset / cache / Dalvik cache if i use TWRP ?
Every advice is welcome, thank you
xperia s 2013 jelly bean
I have a question for xperia s jellybean 4.1.2 , i already root it using some other easy method and i wanna know how to flash rom on to that , i have no idea how to flash a rom and i m scared if i try this something might happen so i m asking for help?:laugh:
I know its ment to be straight forward but I have become stuck...
In step 4 - "Click 6/7" when using the Xperia Flasher where do I find the boot.img i need to put on my phone?
Thanks
---------- Post added at 01:37 AM ---------- Previous post was at 12:45 AM ----------
chuckie987 said:
I know its ment to be straight forward but I have become stuck...
In step 4 - "Click 6/7" when using the Xperia Flasher where do I find the boot.img i need to put on my phone?
Thanks
Click to expand...
Click to collapse
It would appear the ROM i downloaded didnt have a kernel.img but now i have a differant ROM and it has a boot.img so all good again!
Can i follow this method on xperia sl and also can i flash xperia s roms to xperia sl.....my boatloader is unlocked but phone isnt rooted so i guess i will skip unlock boatloader method.....which kernel should i flash for slimbean 4.3...it will be great help if someone answer these questions
Please Help
Hi, I searched a lot for the way to flash a custom rom on my Xperia S. But now halfway through, I've got a problem. My device says it does not allow to unlock bootloader, so does that mean that there is no way I can flash a custom rom on my phone? :crying:
mjk123 said:
Hi, I searched a lot for the way to flash a custom rom on my Xperia S. But now halfway through, I've got a problem. My device says it does not allow to unlock bootloader, so does that mean that there is no way I can flash a custom rom on my phone? :crying:
Click to expand...
Click to collapse
You can use only Stock based ROM for locked bootloaders, not the unlocked bootloaders one.
This is very nice thread. For begginers like me in the rooting this.... loved it. i wast to ask a question
can we flash any zip file using flashtool or there are onle few specific files?
mr.sky10295 said:
This is very nice thread. For begginers like me in the rooting this.... loved it. i wast to ask a question
can we flash any zip file using flashtool or there are onle few specific files?
Click to expand...
Click to collapse
You cannot flash .zip files using flashtool. You can flash only Firmwares or kernel files using flashtool.
Mirhawk said:
You cannot flash .zip files using flashtool. You can flash only Firmwares or kernel files using flashtool.
Click to expand...
Click to collapse
ohh...then is there any other method to flash zips otherthan going into recovery?
i am asking because my recovery is not working. when i go into recovery, blank black screen comes up. and it gets stuck there. i waited for very long time to make sure that it is stuck
mr.sky10295 said:
ohh...then is there any other method to flash zips otherthan going into recovery?
i am asking because my recovery is not working. when i go into recovery, blank black screen comes up. and it gets stuck there. i waited for very long time to make sure that it is stuck
Click to expand...
Click to collapse
Which recovery are You using? The 2.8.1.0? It doesn't work with Xperia S. Use the 2.8.0.1 version.
Mirhawk said:
Which recovery are You using? The 2.8.1.0? It doesn't work with Xperia S. Use the 2.8.0.1 version.
Click to expand...
Click to collapse
Wait i will let you know the complete story.
so what happened is
first i was on CM11 for few mnths then switched to MIUIv5 for 1 month. everything was working fine
but when day before yesterday i flashed PA rom i am not able to access the recovery now (previously there was TWRP in my XS). now i can't flash any zip file
when i reboot to recovery it gets stuck on black blank screen. Even the recovery apps like twrp are not working. when i tried to install recovery through app, the app crashes.
As recovery is not working i cant even switch to other roms or any zip file.
i am totally stuck on this ROM
i asked this que on sony mobile group on FB (created by some sony fans), one of the member said "probably this is not ROM fault but the kernel fault. consider trying new kernel"
mr.sky10295 said:
Wait i will let you know the complete story.
so what happened is
first i was on CM11 for few mnths then switched to MIUIv5 for 1 month. everything was working fine
but when day before yesterday i flashed PA rom i am not able to access the recovery now (previously there was TWRP in my XS). now i can't flash any zip file
when i reboot to recovery it gets stuck on black blank screen. Even the recovery apps like twrp are not working. when i tried to install recovery through app, the app crashes.
As recovery is not working i cant even switch to other roms or any zip file.
i am totally stuck on this ROM
i asked this que on sony mobile group on FB (created by some sony fans), one of the member said "probably this is not ROM fault but the kernel fault. consider trying new kernel"
Click to expand...
Click to collapse
If You are on Beta 6 of PA, it doesn't have twrp or cwm. Flash the twrp v2.8.0.1 by terminal emulator method.
Mirhawk said:
If You are on Beta 6 of PA, it doesn't have twrp or cwm. Flash the twrp v2.8.0.1 by terminal emulator method.
Click to expand...
Click to collapse
i am on PA 4.6 BETA4
terminal emulator means the android app or PC's cmd?
PS: sorry giving you too much trouble by asking stupid questions. but i dont have much knowledge about this things deeply. so kindly bear me for some time.
mr.sky10295 said:
i am on PA 4.6 BETA4
terminal emulator means the android app or PC's cmd?
PS: sorry giving you too much trouble by asking stupid questions. but i dont have much knowledge about this things deeply. so kindly bear me for some time.
Click to expand...
Click to collapse
Ah yes, even that one doesn't have recovery.
Unlocked bootloader is must.
You need an Android app. You can find the app here. Also, here is the page of the twrp.
What You need to do is, download the twrp from here. Rename it to fotakernel.img .
Then copy it to Your sdcard.
Then run the following commands on the terminal emulator app:
Code:
su
dd if=/sdcard/fotakernel.img of=/dev/block/mmcblk0p11
TWRP installed!

[GUIDE] HOW to FLASH latest WW/CN/TW | ROOT | UNBRICK |

I. Before You Begin Doing Anything
**As with all of these types of tutorials, this may void the warranty of your device. Do it at your own risk.
**Download and install the Asus USB Drivers on your PC, if you haven’t done so yet.
**This should only work on a Windows based PC only.
II. Downloading Required Files
** Necessary tools and Drivers - Mediafire Folder
**Latest OTA form ASUS website : WW_2.17.40.12
** Boot.img, Droidboot.img and Recovery.img from this MEGA Drive posted by Chinaphonearena user and belong to Shakalaca.
** System.img - if you want your phone ROOTed on latest ASUS ZF2 Firmware.
III. Yeah! Im ready to do it
**Plug in your device to your PC using a USB cable.
**Boot your device to fastboot mode Power + Vol Up to enter Bootloader Mode
**Hold down Shift and Right-Click anywhere in Fastboot Folder on your PC and select Open command here. It will launch a Command Prompt Window for you to issue commands to your device.
**When it launches, type in the following command and press Enter (.img files has to be in same folder as fastboot tools):
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash fastboot droidboot.img - droidboot.img is fastboot, and if you somehow will flash corrupted image, you won't be able to boot to fastboot anymore. Thanks to sorg
fastboot flash system system.img - Only if you use Pre-ROOTed system image from MEGA Drive.
IV. Ready to go with OTA!
** Upload WW_2.17.40.12 or latest Firmware OTA ( Full firmware ) file to phone storage (Phone storage/File.zip)
** After uploading .zip OTA file to phone storage, unplug USB cable from phone. You will recieve notification that new OTA UPDATE is avaliable for installation.
When you bought CN version of ZF2 you may have to Rename OTA file from UL-Z00A-WW-2.17.40.12-user.zip to UL-Z00A-CN-2.17.40.12-user.zip to get notification about update avaliable.
** Wait till update will finish (approx 10 - 15 min) . Phone will restart when finished. First boot may take longer.
V. Dam! No Notification!? what now...
** Boot your device to fastboot mode Power + Vol Up to enter Bootloader Mode
** At Bootloader press Vol Up to choose Recovery Mode
** You will see an error message of updating ota. Wait 5 sec and then press Power + Vol Up simultaneously until you see recovery menu.
** Using Vol Down + Vol Up choose ADB mode and connect your phone to PC via USB cable
** You need Fastboot version 1.0.32 and up to make ADB Sideload working properly with Zenfone 2
** Extract Fastboot.zip somewhere at your PC and put OTA update file ( .zip) in same folder as Fastboot.
** Hold down Shift and Right-Click anywhere in Fastboot Folder on your PC and select Open command here. It will launch a Command Prompt Window for you to issue commands to your device.
** Use command : adb sideload filename.zip
** At 100% it will go back to Recovery Mode main menu. Restart your phone.
** Done !
** Hit THANKS button and RATE this thread for 5 STARS !​
Credits to : Chinaphonearena for posting a link to latest pre-rooted system images.
Credits to : Shakalaca for making it all possible
Remember ! You should only do this at your own responsibility.
Please note !
If you posting somwhere else my guide. Please give me a Credit or just link to this thread. Thanks​
Please read all pages if you have a issue with guide. I believe other people had it as well and its already solved.​
vivix said:
1) Download image files http://www.mediafire.com/folder/setyy42t2cymy#dy87k1a0f8m81
2) Boot to fastboot mode (Power + Vol Up)
3) Using ADB command prompt flash files by using fastboot commands :
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash fastboot droidboot.img
4) reboot phone
5) upload 2.15.40.10 OTA file to phone storage (http://dlcdnet.asus.com/pub/ASUS/Ze...user.zip?_ga=1.221138204.542811237.1430874705)
6) Update via notification about new update avaliable
7)Wait till update will finish (approx 10 min)
8)Enjoy
Say thanks if i helpedI lost 6 hours to achieve this.
Click to expand...
Click to collapse
Are you sure this works i mean there are thousands of threads regarding this issue but none of them work..Can someone with CN version confirm the working of this method....
I bought phone on Aliexpress website. Phone has WW OTA but update via Wi-Fi was impossible. Firmware was 13.40.13 so i think people with that firmware had CN version at start, then sellers updated it to 13.40.13 WW and sended to buyers. Following my method you can update to the latest WW.
Works fine. We've published a similar method. I recommend using the latest rooted ROM. Note, your LTE 4G bands won't be changed with this method.
Have written out the steps in detail for novice users. Includes setting up adb etc: http://www.chinaphonearena.com/forum/showthread.php?tid=10253
Chinaphonearena said:
Works fine. We've published a similar method. I recommend using the latest rooted ROM. Note, your LTE 4G bands won't be changed with this method.
Have written out the steps in detail for novice users. Includes setting up adb etc: http://www.chinaphonearena.com/forum/showthread.php?tid=10253
Click to expand...
Click to collapse
I agree.
But your method is only for pre-rooted system.img with 2.13.40.13 firmware.
I posted method for full OTA firmware upgrade.
Yes, it is similar )
vivix said:
I agree.
But your method is only for pre-rooted system.img with 2.13.40.13 firmware.
I posted method for full OTA firmware upgrade.
Yes, it is similar )
Click to expand...
Click to collapse
The method posted can be done with any system.img (don't have to use rooted ROM), there's no need to do the OTA update as its already the latest ROM (though it will be compatible with future OTA updates, thanks to the ROM creator), and you end up rooted.
They are essentially the same, except for flashing system.img at fastboot instead of doing OTA update. Take your pick. If not caring about root, your method is certainly quicker, as there's no need to DL the huge system.img file.
Thanks. Much appreciated
confirmed works fine on a rooted CN version
Hi,
I followed all the steps and apart from thinking I'd bricked it (the system update screen was sat with the blue bar unmoved for 15 minutes) . It's just completed perfectly.
Really great advice - thanks - I got 2 of these handsets yesterday via ebay both came rooted and it turns out they are CN models but had WW software on them - as per your model - prior to reading your post I was probably going to try and send them back.
I hope and presume for future updates I can continue to use this method?
will do 2nd one now.
Cheers
Ian
Thanksssssssssssssssssssss
Honestly, last time that I tried to have a custom ROM or in any other words, last time I installed and used ( I'm still using it) it was on my samsung galaxy tab(the first galaxy tab of all time) two years ago!
At first I was puzzled in all of these forum pages. I started to change my CN rom to WW Rom yesterday at 2 o'clock. Since I started this process, I just ate dinner and slept for 5 hours. The rest of the time I was trying to install 7 different roms which are available in this forum or asus zenfone forum by 3 different methods of loading a ROM! NONE OF THEM WORKED CORRECT AND COMPLETELY. so I had to start again and read. I can easily say that I've read more than a fat ass book for this process (most of them were duplicates, but I was looking for s.th new among them...)
Your method worked just nolw (@ 1 pm) and I'm really thankful. Honestly I was so bumped and I was thinking to send this device back, just an hour ago I saw your way for the second time and I just decided to try this time as the last way, before returning it!! thank u again for giving me a zenfone
keep up the good work
Confirmed ok on 2nd handset - red CN model 32gb 4gb ram.
It has removed the root access though... Supersu app has gone. and Root checker confirms not rooted.
Which is ok because I can now use Skygo app on the phone - really wasn't expecting that to work!
Thanks guys for good news that it work for you too. I hope that TUT will help others to get rid of 13.40.13 which drain battery as $%^&. Without root it's hard for efficient battery save but atm i use battery doctor from G market and I need to say after 4h it drained 3% battery with turned WiFi. I just wait for proper root tutorial.
vivix said:
Thanks guys for good news that it work for you too. I hope that TUT will help others to get rid of 13.40.13 which drain battery as $%^&. Without root it's hard for efficient battery save but atm i use battery doctor from G market and I need to say after 4h it drained 3% battery with turned WiFi. I just wait for proper root tutorial.
Click to expand...
Click to collapse
Several proper root tutorials already posted. Just follow your own tutorial but flash the pre-rooted system.img. Bam, done.
But latest system.img is not from newest bug fixed firmware mate. That's the problem.
vivix said:
But latest system.img is not from newest bug fixed firmware mate. That's the problem.
Click to expand...
Click to collapse
Latest pre-rooted system.img is the latest ROM available and OTA updateable.
https://www.mediafire.com/folder/k7z5qzh579oc4/Asus_Zenfone_2_ROOT_System_Image
Hello,
Im stuck at no.5, sorry to ask but I don't know what you mean by phone root storage and where it is found.
Can you help please
He means the base of your SD card. Don't copy the OTA into a folder on SD. Copy it to the base of the SD.
with my cable still connected and fastboot still open?
Because I have put it in the sd card nothing happen
Reboot the phone. You should get an OTA update notification. Or boot into recovery and apply the update from there.
Chinaphonearena said:
Latest pre-rooted system.img is the latest ROM available and OTA updateable.
https://www.mediafire.com/folder/k7z5qzh579oc4/Asus_Zenfone_2_ROOT_System_Image
Click to expand...
Click to collapse
Latest WW Firmware is : Version WW_2.15.40.10
Latest pre-rooted system.img you posted is : Version WW_2.13.40.13
I just rewrited whole GUIDE to make it more easier to understand.
vivix said:
1) Download 2.15.40.10 .img files from : http://www.mediafire.com/folder/setyy42t2cymy#dy87k1a0f8m81
2) Boot to fastboot mode (Power + Vol Up) to enter Bootloader Manu and connect it to PC using USB cable provided.
3) Download ADB TOOLS : http://tools.asuszenfoneblog.com/2014/10/adb-fastboot-tool.html
TIP : At Flashtool/fastboot folder <b>press Shift+Right Click then Open Command Here
Using ADB command prompt flash files by using following fastboot commands :
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash fastboot droidboot.img
4) Reboot phone connected to PC
5) Upload 2.15.40.10 Firmware OTA file to phone storage (Phone storage/File.zip) :
http://dlcdnet.asus.com/pub/ASUS/Ze...user.zip?_ga=1.221138204.542811237.1430874705
6) After uploading .zip file to phone storage, unplug USB cable from phone.
You will recieve notification that new OTS UPDATE is avaliable for installation.
7)Wait till update will finish (approx 10 - 15 min) . Phone will restart when finished.
Dont touch phone because you can mess up something .
8)Enjoy latest V2.15.40.10 WW Firmware.
Say THANKS if i helped !
I Lost 6 hours to achieve this and only THIS method working for 100%.​
You will lose your ROOT.
Be careful! Pre-rooted system.img widely avaliable have glitch where when you update superuser app you will soft/hard brick your phone, bootloops etc.
Above method work also as UNBRICK method.​
Click to expand...
Click to collapse
You fail to give credit to those who made this possible, especially shakalaca.
This is my version of the steps:
ddfault said:
I recommend using the tools directly from google. (Links fixed 2015MAY08)
These include fastboot and adb
Windows SHA1:720214bd29d08eb82673cd81a8159b083eef19d7
Linux SHA1:b78be9cc31cf9f9fe0609e29a6a133beacf03b52
MacOS SHA1:ddc96385bccf8a15d4f8a11eb1cb9d2a08a531c8
Click to expand...
Click to collapse
As far as steps, I can only speak of the ZE551ML. Start with an unrooted OS.
1.) Download the ADB and Fastboot tools from google (see links above). Download the pre-rooted from from shakalaca in post #1 (If you download the 200MB split version, Windows File Explorer will allow you to open the .zip and copy the .img file out.)
2.) Download the stock full ROM WW_2.15.40.10 directly from support.asus.com
3.) Plug the phone into the PC via USB and copy the UL-Z00A-WW-2.15.40.10-user.zip onto the phone.
4.) The phone will notify you that there is an update:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5.) When you select the notification you will be prompted of which file to use in the update:
6.) Hit OK and the phone will reboot and update everything it needs to update per ASUS. (This will include the fastboot/droidboot image, boot, recovery, system, silentlake, and modem firmware.)
7.) Once the update has completed, unplug and power off the phone.
8.) While holding volume up, press the power button until the phone vibrates. At this point release the power button but keep holding the volume up button until the screen flickers to the fastboot menu. Release the volume button when the screen flickers.
9.) Plug the phone back into your computer, open a command prompt and navigate to where you extracted the google tools and the system.img.
10.) Run:
fastboot devices
11.) You should see a your device listed, if you do not, your device is not in fastboot mode.
12.) Assuming you see your device listed in Step 10, run:
fastboot flash system system.img
This will erase your current system partition and then start writting the new image to the partition. Fastboot will split the system.img file into ruffly 500MB chucks and send them to your device.
13.) Once its finished, you can select boot normally on your phone by pressing the power button or run:
fastboot reboot[/QUOTE]

Blu Life One XL 6.0 link to download UPGRADE *

* *Support and Info thread* *Starting with kitkat 4.4.4. KTU84P​ ABOUT
Looking at the build #
and the Custom build# for Android 4.4.4 and 5.0.2​* Blu Life One XL KTU84P*
* KIT KAT 4.4.4 *
* Build number : KTU84P
* Custom build version : X030Q_V07_GENERIC 03-07-2015
* Blu Life One XL LRX22G*
* Lollipop 5.0.2 *
* Build number : LRX22G
* Custom build version : X30Q_V10_L_GENERIC 01-29-2016
NOTE:
Custom build date 03-07-2015
factory date that's on this phone,
may not be your date..??​
Read more .......Can be rooted. TWRP can be put on the KITKAT version so far. need help with 5.0.2 TWRP .
6.0 https://androidmtk.com/download-blu-stock-rom-models 6.0
-------------------------------------------------------------------------------------------------------------------------------------------
* LIFE ONE AND LIFE ONE XL FLASHING PROCEDURES *
@Using the Qualcomm flash image loader (QFIL)@
Drivers
1. PC needs to be turned on with “Disable driver signature enforcement” mode. - Press the “Windows logo key + X” at the same time, then click “Command Prompt (Admin). - Type: bcdedit /set testsigning on -Press enter then restart PC.
-If done correctly bottom right of PC should show “Test Mode”.
2. Run “Setup.exe” inside “Life One XL Drivers” folder.
Flashing software - QFIL
1. Download and extract software for device.
https://androidmtk.com/use-qualcomm-flash-image-loader-qfil
all instruction on the above link.
2. To install tool run “setup.exe” inside folder “QPST.2.7.425”. 3. When setup finishes click the Windows logo key > All Programs > QPST > QFIL
------------------------------------------------SPECIFICATIONS----------------------------------------------------------------
TECHNOLOGY
Android v4.4 KitKat, upgrade-able to Android 5.0 ?? YES it is... I have the
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Lollipop
3G 850/1700/1900/2100
4G LTE 700/1700/2600
Processor
64-Bit Qualcomm 1.2GHz Quad-Core
with Adreno 306 GPU
MEMORY
Internal 8GB, 1GB RAM
Micro SD Slot up to 64GB
DISPLAY
BLU Infinite View Technology (IPS)
5.5 HD 720 x 1280, 268 ppi
CAMERA
13MP Main | 5MP Front Camera |
LED Flash
HD 1080p Video @30fps
CONNECTIVITY
Bluetooth 4.0
Wifi, Hotspot
MicroUSB v2.0
SOME GOOD READING.. thank you all
http://forum.xda-developers.com/showthread.php?t=2317790
Thank you shimp208
DOWNLOAD
Minimal ADB and FASTBOOT
ALWAYS BACKUP
Downloaded * app called
BACK UP PARTITION
ADB and FAST BOOT
YOU will need
ADB FAST BOOT program - Install / with ADB driver
a list of commands - c : \ adb>
adb devices
adb reboot bootloader
fastboot devices
FILES FOR NEW RECOVERY AND INSTALLING ROM FILES NEEDED
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot reboot
.
Need qcn please
Enviado desde mi iPhone utilizando Tapatalk
Help
An Android update to 5.0.2 was released about a month ago that has made my phone run very slow and a fix has still not been released. I also have yet to receive a response from BLU support on what my options are. Prior to the update, the phone ran considerably better and now get hung up while performing mild multi-tasking such as switching between SMS and Facebook. Performing a Factory reset down not roll back the android version. I am trying to find an older android version but am not having much luck. All help is appreciated.
Model Number: BLU LIFE ONE XL
Processor: Qualcomm-Technologies MSM8916
Build: BLU_X030Q_V10_L_GENERIC
Screenshot
Here is a screen shot of my forced flashed upgrade to Lollipop 5.0.2
factory image found on needrom + Mediafire
You can use the SP FLASH TOOLS .......no need to root . Put phone into install mode.. UN-check ALL check mark in USB connection.
https://drive.google.com/open?id=0Byjq3QLeYsombkJKbG5VcERVbkU
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
can be rooted, No yet to put a recovery {twrp / or cwr } on this version Lollipop 5.0.2
no recovery [ twrp ] or [ cwr ]
Rooted with kingoroot backed up with Partition backup and restore
Steps to install TWRP on BLU Life One XL
Goto official TWRP page and download twrp-2.8.x.x-xxx.img file for your BLU Life One XL. Keep twrp-2.8.x.x-xxx.img file in a separate folder.
Your PC must have ADB & fastboot installed and configured. For quick installation try 15 Second ADB installer. Download link
Now connect your device to your PC and goto twrp folder and press and hold shift then rightclick on white space and "Open command window here".
Now type following commands at command prompt.
"adb reboot bootloader" - to boot your device into bootloader.
after booting into bootloader type "fastboot flash recovery twrp-2.8.x.x-xxx.img" - this will flash TWRP recovery on your BLU Life One XL.
"fastboot reboot" - to reboot your device.
After reboot type "adb reboot recovery" - to boot into recovery mode.
BOOT and RECOVERY image files
boot and recovery image in zip file
nandroid backup https://drive.google.com/file/d/0B_IWTAANhFJRcDg4ajJ6V0JrTmM/view
1View attachment 39739272View attachment 39739283View attachment 39739294View attachment 39739305View attachment 39739316View attachment 3973932
MODEL number
BLU LIFE ON XL
Build number
LRX22G release-keys
Custom build version
BLU_030Q_V10_GENERIC 29-01-2016 18:15:good:
Dude I'm just happy you responded to me about your backup. I almost gave up on this phone because i looked everywhere on the internet and it seemed as if the phone didn't exist to a stock ROM. Like i said before... I have twrp and root and no OS and just needed someone to make a backup using twrp so I can install it on my phone or at least find a stock one that I can use with twrp. Luckily you came thru and thank you for your response. Hopefully I don't have to use this cheapo (second phone) for long.
Sent from my XT1526 using XDA-Developers mobile app
Partition list
List of partiton files for the BLU LIFE ONE XL
RECOMMEND TO GET THIS APP after root access .
Also set app to save as IMG files . these are recommend to use in restore.
DDR ----------mmcblk0p19
ABOOT-------mmcblk0p4
ABOOTBAK--mmcblk0p5
BOOT---------mmcblk0p22
CACHE--------mmcblk0p25
CONFIG-------mmcblk0p28
FSC------------mmcblk0p16
FSG------------mmcblk0p20
HYP------------mmcblk0p10
HYPBAK-------mmcblk0p11
KEYSTORE-----mmcblk0p27
MISC-----------mmcblk0p15
MODEM-----mmcblk0p1 *EFS/IMEI*
MODEMST1--mmcblk0p13 *EFS/IMEI*
MODEMST2--mmcblk0p14 *EFS/IMEI*
OEM------------mmcblk0p29
PAD-------------mmcblk0p12
PERSIST---------mmcblk0p24
RECOVERY------mmcblk0p26
RPM -------------mmcblk0p6
RPMBAK---------mmcblk0p7
SBL1--------------mmcblk0p2
SBL1BAK --------mmcblk0p3
SEC---------------mmcblk0p21
SPLASH----------mmcblk0p18
SSD---------------mmcblk0p17
SYSTEM----------mmcblk0p23
TZ-----------------mmcblk0p8
TZBANK----------mmcblk0p30
USERDATA-------mmcblk0p
URL
reserved
LINKS TO DOWNLOAD
BLU LIFE ONE XL
WITH TWRP X030Q_V07_TWRP
https://www.dropbox.com/s/axx3ig6yl8vzixx/X030Q_V07_twrp.zip?dl=0​
Inspired
Deejaydark said:
Dude I'm just happy you responded to me about your backup. I almost gave up on this phone because i looked everywhere on the internet and it seemed as if the phone didn't exist to a stock ROM. Like i said before... I have twrp and root and no OS and just needed someone to make a backup using TWRP so I can install it on my phone or at least find a stock one that I can use with TWRP . Luckily you came thru and thank you for your response. Hopefully I don't have to use this cheapo (second phone) for long.
Sent from my XT1526 using XDA-Developers mobile app
Click to expand...
Click to collapse
did a lot of reading .... to find out it was only a corrupt boot image ... I was only getting TWRP recovery to load.
after reading About ADB and FASTBOOT
I learned how to flash the boot image , but first i need the ADB driver install on my PC.
Im not good at writing directions , but i took notes.... also was able to make back ups of all partitions.... We really only need to fix the ones we over written ... In my case was only boot image and recovery image.... my system was in tack..
thank you for inspiring me to go the distance.... I learned alot.
Rickrocks013 said:
did a lot of reading .... to find out it was only a corrupt boot image ... I was only getting TWRP recovery to load.
after reading About ADB and FASTBOOT
I learned how to flash the boot image , but first i need the ADB driver install on my PC.
Im not good at writing directions , but i took notes.... also was able to make back ups of all partitions.... We really only need to fix the ones we over written ... In my case was only boot image and recovery image.... my system was in tack..
thank you for inspiring me to go the distance.... I learned alot.
Click to expand...
Click to collapse
So I can install this with TWRP?
Sent from my XT1526 using XDA-Developers mobile app
vastalant said:
An Android update to 5.0.2 was released about a month ago that has made my phone run very slow and a fix has still not been released. I also have yet to receive a response from BLU support on what my options are. Prior to the update, the phone ran considerably better and now get hung up while performing mild multi-tasking such as switching between SMS and Facebook. Performing a Factory reset down not roll back the android version. I am trying to find an older android version but am not having much luck. All help is appreciated.
Model Number: BLU LIFE ONE XL
Processor: Qualcomm-Technologies MSM8916
Build: BLU_X030Q_V10_L_GENERIC
Click to expand...
Click to collapse
Added with my phone rooted w/twrp
Build: BLU_X030Q_V07_L_GENERIC
Deejaydark said:
So I can install this with TWRP?
Sent from my XT1526 using XDA-Developers mobile app
Click to expand...
Click to collapse
already done MOD version of Stock only recovery image and less bloat ware.
NOTE that TWRP is not fully supported... dont use the install to find your phone..
works great on backing up in recovery. must have root access .
Rickrocks013 said:
already done MOD version of Stock only recovery image and less bloat ware.
NOTE that TWRP is not fully supported... dont use the install to find your phone..
works great on backing up in recovery. must have root access .
Click to expand...
Click to collapse
So how do I install this zip file? My phone is already Rooted with TWRP.
Zenfone 2 Deluxe Special Edition
Deejaydark said:
So how do I install this zip file? My phone is already Rooted with TWRP.
Zenfone 2 Deluxe Special Edition
Click to expand...
Click to collapse
You need to unzip them on a pc or your SDCARD and flash in TWRP recovery mode... take your SDCARD out put on with pc.
THERES STOCK IMAGES also
2 method
1. ADB command with FASTBOOT read
http://www.xda-developers.com/how-to-install-twrp/
2. USE BACKUP in twrp ..after making a folder on sdcard TWRP another one BACKUP . unzip here.... get a zip program
tools.. zip program
I want to say thank you for getting my phone working again. Everything is working like it should.
Deejaydark said:
I want to say thank you for getting my phone working again. Everything is working like it should.
Click to expand...
Click to collapse
I must say i'm glad you got your phone back up and running..........
I know i put together a wild combo of files in the zip file..........
I hope it wasn't to hard to figure out......
. I labeled them the best i could.......
I can now flash upgrade with adb commands..... I don't need TWRP ,, its nice to know it works
The one thing I read is the most important is making a nandroid backup... all partitions in one Image file
Nice
---------- Post added at 05:31 AM ---------- Previous post was at 05:25 AM ----------
Now all we need is some ROMs
BLU Life One XL
Stock w/Twrp & Root
**FLASHING WITH QUALCOMM TOOLS**
Using the Qualcomm flash image loader (QFIL)
LIFE ONE AND LIFE ONE XL FLASHING PROCEDURES
Drivers
1. PC needs to be turned on with “Disable driver signature enforcement” mode. - Press the “Windows logo key + X” at the same time, then click “Command Prompt (Admin). - Type: bcdedit /set testsigning on -Press enter then restart PC.
-If done correctly bottom right of PC should show “Test Mode”.
2. Run “Setup.exe” inside “Life One XL Drivers” folder.
Flashing software - QFIL
1. Download and extract software for device. 2. To install tool run “setup.exe” inside folder “QPST.2.7.425”. 3. When setup finishes click the Windows logo key > All Programs > QPST > QFIL

[STOCK] D851 30D KDZ + Flashable ZIPs + All IMGs (Marshmallow!!)

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
T-Mobile LG G3 D851 30D​
This thread covers various methods of installing both stock and stock rooted Marshmallow 6.0 30D onto the T-Mobile LG G3 D851.​​
Information:
30D is the first official Marshmallow Android 6 update for the T-Mobile LG G3.
It was first released in KDZ form the morning of April 27 2016.
Official update methods include both an OTA update from 20G to 30D and a KDZ update through the LG Mobile Support Tool.
The bootloader is still unlocked with no sort of OEM Unlock toggle. Still no bootloader/fastboot mode.
Kingroot can temp-root 30D! At least 1 Marshmallow build will always have root. Not very secure... but good for modders.
Android Version: 6.0
Android security patch level: 2016-04-01
Baseband version: MPSS.DI.2.0.1.c1.13-00114-M8974AAAAANPZM-1.43646.2
Kernel version: 3.4.0
Build number: MRA58K
Software version D85130d
Security software version: MDF v1.1 Release 2
Install Directions:
OTA:
When the software update is available, the update icon will display in the status bar at the top of the screen.
Swipe down from the top and tap the notification.
Restart & Install
Note: If prompted, connect to a Wi-Fi network to download the software update.
Your device will restart to perform the update.
When the update is complete, your phone will restart and transition through a series of alerts stating "Android is upgrading".
Once your phone has powered on you will be notified that the software update successfully installed. Tap "OK" to close the notification.
Troubleshooting
If you have not been notified of an available software update, you can manually check if one is available.
From the Home Screen, tap Apps > Settings > General Tab > About phone
System updates > Check now to manually check for a new update.
You will be prompted if a new software update is available.
LG Mobile Flash Tool:
Click here to download the LG Mobile Support Tool to your computer, then open.
Connect your phone to your PC.
Tap Start Upgrade within the LG Mobile Support Tool to begin.
Device will progress through Analysis, Download, Update and Complete during the update process.
While updating, the device will power off and enter a download mode at 5% completion. This is normal. DO NOT DISCONNECT THE USB CABLE!
At approx 95% of completion, the device will power on. This may take several minutes. This is normal. DO NOT DISCONNECT THE USB CABLE!
If your software update stops before it has completed, please do not close the update tool and try the update again. Additional troubleshooting steps are below.
The tool will notify you when the update is complete. Tap Exit to return to the main screen.
Wait for device to power on. Once powered on, the device will reconnect to the LG Mobile Support Tool. When connected, observe that the version number reflects the latest Software D85110r. It is now OK to DISCONNECT THE USB CABLE.
Troubleshooting
If the phone software upgrade stopped before completion, please do not close the update tool and try to update again following original instructions.
If you already closed the update tool, and the phone will not turn on normally, please follow the steps below:
Remove back cover and battery.
Record IMEI/ESN/MEID from device label in battery well.
Replace battery and back cover.
Open LG Mobile Support Tool.
Connect the device to PC via USB cable.
From the drop down menu, select Options > Upgrade Recovery.
Enter your phone information and tap OK
After checking the phone information, it will start to update automatically. If it does not work, the device may require service to attempt recovery.
TWRP + Flashable-ZIPs:
These directions should be used by anyone who already has TWRP installed on their D851.
I used the latest TWRP 3.0 build @ https://dl.twrp.me/d851/
Don't want root? Then it's probably easiest to just flash the stock KDZ using LGUP.. or just skip the SuperSu steps.
1. Download the following 3 files and place them on the internal or external sdcard:
a. LG-D85130D-Flashable.COMPLETE.zip
b. LG-D85130D-Flashable.Boot-AUTOREPACK.zip
c. SuperSU 2.65 or higher. [STABLE] or [BETA] Thanks to Chainfire!​2. (re)Boot into TWRP if not there already.
3.* Backup current partitions: boot, system, data, efs (backing up anything is optional but suggested)
4.* Up to you if you want to wipe data (TWRP > Wipe > Swipe slider) but not needed if coming from a stock rom.
5. Install the 3 zip files you put on your sdcard, 1 at a time:
a. LG-D85130D-Flashable.COMPLETE.zip (Install > select zip > swipe to confirm/flash)
b. LG-D85130D-Flashable.Boot-AUTOREPACK.zip (Install > select zip > swipe to confirm/flash)
c. SuperSU zip (Install > select zip > swipe to confirm/flash)​
After zips finish flashing you can reboot! If TWRP asks if you want to install SU, hit no. If TWRP says No OS installed, ignore it.
Alternatively, if you are already on 30D already without root and want root/TWRP you can use Kingroot.
Click the button below to display how-to steps...
1. Download the latest Kingroot APK here.
2. Install Kingroot and get temproot with it.
3. Download TWRP @ https://dl.twrp.me/d851/ and download LG-D85130D-Flashable.Boot-AUTOREPACK.zip linked below.
4. Enable USB Debugging on your D851 and connect your device to the computer and run the following commands to install TWRP.
Code:
adb push LG-D85130D-Flashable.Boot-AUTOREPACK.zip /sdcard/
adb push twrp-3.0.0-0-d851.img /sdcard/
adb shell
su
dd if=/sdcard/twrp-3.0.0-0-d851.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
reboot recovery
[if no computer]
d/l TWRP n Boo Repack onto phone n move it to root of internal storage.
Run the su, dd and reboot commands above in terminal emulator.
5.* Backup current partitions: boot, system, data, efs (backing up anything is optional but suggested)
6.* Up to you if you want to wipe data (TWRP > Wipe > Swipe slider) but not needed if coming from a stock rom.
7. Install the 2 zip files you put on your sdcard, 1 at a time:
a. LG-D85130D-Flashable.Boot-AUTOREPACK.zip (Install > select zip > swipe to confirm/flash)
b. SuperSU zip (Install > select zip > swipe to confirm/flash)​
Downloads:
Please do not mirror my files!
LG-D85130D-Flashable.COMPLETE.zip
100% stock untouched system, boot, modem and bootloader. Recovery is not included so you don't lose TWRP.
LG-D85130D-Flashable.Modem.zip
This is a flashable stock 30D modem.
LG-D85130D-Flashable.Boot.zip
This is a flashable stock 30D boot.img. Boot.img contains kernel + dtb + ramdisk.
LG-D85130D-Flashable.Boot-AUTOREPACK.zip
This is a repacked boot.img to work properly when flashing SuperSu in TWRP.
LG-D85130D-Flashable.Bootloader.zip
This is a flashable stock 30D bootloader. It contains aboot, dbi, factory, laf, rpm, sbl1 and tz.
Also, KDZ + all stock images for 30D are available in the link below...
CODEFIRE DIRECTORY
30D KDZ Mirror Here
MD5 Sums:
Click button below to view MD5 for each file...
MD5 (aboot.img) = 3a984c57cea36f8356f5068cc7cdd4b4
MD5 (boot.img) = 98bfe8aaeb7e169d78ad249b5c362214
MD5 (dbi.img) = 1a78fd7454f7d0a6fa1bc71aa15c12e8
MD5 (factory.img) = 794327b47c4f1cd503591d804ab2a458
MD5 (laf.img) = 1e5971ef828b0d6afdfa4690efa26308
MD5 (modem.img) = 3969d7e27ffb83b5873c0ac9c796ea1d
MD5 (persist.img) = 039a73fb1b36df8cab1c0861cdea6bf3
MD5 (recovery.img) = 339bd050ddfac269f5c1c7ee36217df3
MD5 (rpm.img) = e9d136d6a7fcdd3726696a111f4b8f8e
MD5 (sbl1.img) = c4ec620062aaa2f7ebafa67c43218665
MD5 (system.img) = f22c8366fab71f65f5f50c7e8eaaa1cd
MD5 (tz.img) = 36a7d694d17f0f8183c0afb825dc9512
MD5 (LG-D85130D-Flashable.Boot-AUTOREPACK.zip) = f7f9507a81333f0a4e8a16033018e8b9
MD5 (LG-D85130D-Flashable.Boot.zip) = ffba4ffc1842c65b1f1defc2dc103330
MD5 (LG-D85130D-Flashable.Bootloader.zip) = cf37b49ab3b85eba9d0d43c5927d215d
MD5 (LG-D85130D-Flashable.COMPLETE.zip) = d2cbb2c8675bf0adc412b760c05ceb29
MD5 (LG-D85130D-Flashable.Modem.zip) = 87b50d33e7b0fba62847a2792648a310
MD5 (D85130d_00_0404.kdz) = a3d04df6fa1e964bd10b5e2ae59041ae
DISCUSSION THREAD:
Take all your nonsense to the marshmallow general thread here - http://forum.xda-developers.com/tmo...-t-mobile-lg-g3-d851-30d-marshmallow-t3367030
Click to expand...
Click to collapse
y u quote OP?
Follow me on twitter for future updates on LG-related things - twitter.com/@utoprime
Find this thread helpful? Hit the Thanks button!
Feeling extra generous? Click my name at the top of any post and hit donate or click here.
#TEAMCODEFIRE
Looks like name on your hosting site for the repacked boot was named wrong.
Actual file: http://downloads.codefi.re/autoprim...s/30D/LG-D85130D-Flashable.Boot-AUTORPACK.zip
mjoecarroll said:
Looks like name on your hosting site for the repacked boot was named wrong.
Actual file: http://downloads.codefi.re/autoprim...s/30D/LG-D85130D-Flashable.Boot-AUTORPACK.zip
Click to expand...
Click to collapse
404
nachumama said:
404
Click to expand...
Click to collapse
He fixed the link, use the link in the OP
gotcha...... ok so i downloaded all the necessary files but i want to use android pay, should i install superSU or not?
nachumama said:
gotcha...... ok so i downloaded all the necessary files but i want to use android pay, should i install superSU or not?
Click to expand...
Click to collapse
no
keki92 said:
no
Click to expand...
Click to collapse
thanks buddy
Modem and bootloader flashed over 20G and Exodus ROM. No problems to report. Thanks.
How big is he COMPLETE file size itself?
just upgraded ; it works great, thx
just need the stock dialer; t-mobile one is bad to say it lightly
Hello- I am currently using the D851 T Mobile version in New Zealand on Vodafone and all is well. The phone is obviously unlocked.
If I flash this update will I still be unlocked afterwards ?
Thanks To all, LL13-
lamplighter13 said:
Hello- I am currently using the D851 T Mobile version in New Zealand on Vodafone and all is well. The phone is obviously unlocked.
If I flash this update will I still be unlocked afterwards ?
Thanks To all, LL13-
Click to expand...
Click to collapse
Yes
RicardoSal24 said:
Yes
Click to expand...
Click to collapse
WooHoo, Im gonna flash away.
Thanks Ricardo !!! :highfive::highfive:
Hi there. Great work! Quick question though. If I have stock lollipop and it doesn't have root/twrp. The steps to do this would be to root first -> install twrp -> and then follow the steps?
Thanks,
keki92 said:
no
Click to expand...
Click to collapse
Do you need TWRP or Root to use Lg flash tool?
Kenneth_MC said:
Do you need TWRP or Root to use Lg flash tool?
Click to expand...
Click to collapse
No...
@autoprime
As always your work here is appreciated, thank you for the posting, this will benefit everyone.
@autoprime - awesome work, thanks so much!
A couple suggestions/notes, dunno if ypu want to put this in the OP for some people.
1. If you've encrypted your phone, you'll need to unencrypt first.
2. If you have Xposed installed, uninstall it before you start.
My phone feels new with this update, it's great.
Anyone updated please tell me knock code security with 6 taps or 3 taps like 20G? Thanks
If I am currently on CM13, besides the radio, can I flash bootloader and boot? If so which boot?
Thanks for the help.

[HONOR 6x EMUI 8.X Oreo] Installing EMUI 8.X on Honor 6X EMUI 5.X and RAM extend via SD Card

My problem is that I can't run correctly LineageOS on Honor 6x, and I didn't know how to run it properly, and I still don't know how to do it because I got bootloop, even if I factory reset...
=> For future people who still want to know how I switch Honor 6x on EMUI 5.X to EMUI 8.X, I write just below the full step and problems that I met during this process (But I think there is already some thread that talk about this.
________________________________________________________________________________________________________
Installing EMUI 8.X Oreo from scratch on a Honor 6x running with the EMUI 5.X Nougat
First of all, I have to thanks @Djiban that help me for the first step ✌
So, many Custom ROM/AOSP ROM for Honor 6x required an EMUI 8.X base.
And to update your Honor 6x to EMUI 8.X, you MUST DEBRAND your phone to BLN L22 India version of the OS
1/ Requirements (Search on Google for installation and how to use, or ask in this thread below)
Spoiler: 1/ Requirements
- You can choose between those 2 methods (Advise you to take the Huawei MultiTool):
Have ADB and Fastboot tools on Computer: ||__Minimal ADB__|| (also present with Android Studio, Unity3D with Android build support)
For Unity3D, if you had add the Android Build Support, the adb and fastboot tools should be here : C:\Program Files\Unity\Hub\Editor\20XX.X.X\Editor\Data\PlaybackEngines\AndroidPlayer\SDK\platform-tools (Replace 20XX.X.X with your version of Unity 3D)
You can ALSO use ||__Huawei MultiTool v8 __||, that get on more an interface(Great Noob Friendly tools).
I advise you to set the 2 tools inside the Windows 10 environment variable to easily use adb and fastboot command on command prompt. Type adb devices on the console tools of your computer, if it's correctly referenced you will see something like the screenshot:​
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
- Unlock the bootloader of your phone ! (you can use ||__DC unlocker__|| to get the bootloader code for 4€, or if someone know to get the number with a simple batch file code ? It would be awesome) (Huawei don't get you anymore the bootloader code, even with the paid service)
To make DC-UNLOCKER detect your phone :​
In your phone Settings -> About Phone -> Press 7 times the Build Number => To unlock Developpers Options; then go to Settings -> Developpers Options => Enable USB debugging
Install HiSuite from Huawei to get all the drivers needed to detect your Huawei/Honor phone on your computer
You have to type in dial pad(the default phone app) *#*#2846579#*#* then go to ProjectMenu -> Background Settings -> USB Ports Settings -> [U]Manufacture Mode[/U]. You have to redo this if you disconnected your phone, because it will set by default the HiSuite Port !
Once you get the code :​
In your phone Settings -> Developpers Options => Enable Unlocking OEM
Connect your phone to your computer and allow the debugging mode, and choose MTP mode(transfert files, not charging only)
With Huawei Multi-Tool, press Quick Actions(top right of the UI) -> Reboot to Fastboot mode (OS-FB) OR
Open the console (search cmd on windows), and type adb reboot bootloader
Open the console (search cmd on windows), and type fasboot oem unlock YOURCODE
If all good, type in the cmd : fastboot reboot
- MUST install TWRP Recovery 3.1.1 (Other versions will not work for EMUI 5.X Android Nougat) :
Use Huawei MultiTool : In Recovery Tab, it will normally propose you the EMUI5 twrp image or the 3.1.x version. Press Flash Recovery_ramdisk (require you to enable/allow USB debugging on your phone)
You can also choose an image from your download (see link below for twrp 3.1.1)
Or with the cmd
Boot into fastboot : adb reboot bootloader
Install TWRP : fastboot flash recovery twrp-3.1.1-0-berlin.img
||__All TWRP version for Honor 6x[berlin]__||
||__twrp-3.1.1-0-berlin.img__||
- Advise you also to make a backup with HiSuite to save your data, and a TWRP backup to recover your system in case.
- To reboot into TWRP Recovery mode, press Volume + and Power buttons. Or use Huawei MultiTool v8 Quick Actions or type into the cmd : adb reboot recovery
2/ Debrand to BLN-L22
Spoiler: 2/ Debrand to BLN-L22
- See if you already got the BLN-L22 or not : Honor6x -> Settings -> About phone -> Build number
If yes, you can skip this step
View attachment 5233545
- Here is the tutorial made by @shashank1320 to debrand to BLN-L22 (work for BLN and BLL models as I know): ||__LINK__||
(Careful, the 3 links on the firmware finder database may take 1-3 hours to download, they didn't get a good server speed, same as the step 3) And you may need to flash OEMInfo.zip via TWRP !
- Here is some issues that I encounterd and solved, the Huawei MultiTool ZIP is there also : ||__LINK__||
Kentoto2021 said:
OKKK after one all day (9:30AM to 10:30PM) I finally get it !!!!!!! THANK YOU for your advice you saved my phone if I can say Djiban A look of my new version phone below, very happy !!! Now I have to find how to get Emui 8.X on my Honor 6.X without broken my phone
I really thought that my phone was broken because I didn't backup my OEM info with the Huawei MultiTool and ended into a bootanimation loop even restoring my phone with TWRP.
______________________________________________________________________________________
For those who is doing this awesome tutorial : https://forum.xda-developers.com/t/...ln-l22-successful-case-noob-friendly.3679402/ I attach here to my message the Huawei MultiTool v7 that I found on this forum too (but can't find the link in my browser history ) :
For this tool, don't connect to internet when you launch it to avoid auto update, you can enable it after the question about proxy or when you see the main menu. The only bad thing that it's not in english, but the screenshot in the tutorial show you what is what
For the OEM info zip, if you get "sbin/su not found" when restauring int the MultiTool , try also to install it with the traditional way in TWRP via the button Install -> Install ZIP
At the step where you have done the dload method with the update.zip, you will be get stuck in the bootanimation or black screen, it says that you have to shutdown the phone and that's a bit complicated with Honor 6x, you can only reboot whatever you done and adb acess from computer is off (don't activate the bootloader, it can reject the new update you just put in the dload folder !!!)
What I have done is going to Huawei eRecovery mode by pressing and maintaining Power button and Volume +, then choose wipe cache then wipe data/factory reset (it will erase all your data that you have on your last system !). By that, the phone will reboot and get you into the EMUI 5.X and the menu too set your phone, and by that you can rename the folder dload-data to dload through computer as mentionned in the tutorial, then SHUTDOWN your phone and redo the dload activation (Volume + and - and power button pressing)
And that's it ! Some tips to avoid future people stuck for hours and panic because nothing is working and the phone seems to be good for bin
Click to expand...
Click to collapse
WARNING : Once you update the OEM info of your phone, the Huawei eRecovery won't find update to factory reset the entire firmware ! So if the Huawei eRecovery tell you that the system is broken and you have to reset your phone (can't avoid that if it tells you that I think), after that the bootloader will be locked, then you can't go to TWRP recovery or start the OS.
DON'T PANIC, go into fasboot/bootloader by shutting down your phone(if can't, just reboot and do the following steps before the phone vibrates when reboot !) : Hold AND Keep VOLUME - , then plug the USB cable
Then on your computer, unlock the bootloader as you already done with the command : fastboot oem unlock THEBOOTLOADERCODE (The bootloader code will be the same whatever your firmware version is, it's unique for your phone harware)
3/ Update to EMUI 8.X BLN-L22HNC675 [Android 8.0]
Spoiler: 3/ Update to EMUI 8.X BLN-L22HNC675 [Android 8.0]
Here is the firmware finder database same as the previous step if you want to pick other version of your firmware
Online firmware database ⋆ TEAM MT Developers
< PREVIOUS FIND MODEL NEXT > Дата изменения Полное название Файлы обновления Размер Тип G g v f 2021.11.09 MED-LGRP2-OVS 10.1.0.195 filelist 0 OTA 1458 104 519745 3 2021.11.08 patch01 filelist 0 OTA 1458 104 525603 1 2021.11.08 TAS-LGRP1-CHN 11.0.0.170 filelist 0 OTA 1458 104 525098 1 2021.11.08...
pro-teammt.ru
- Here is the tutorial also made by the same author at the step 2 : ||__LINK__||
- Some UPDATE Links about this tutorial:
The HwOTA8 tools : ||__LINK__||
Make sure to keep HWOTA8_BLN folder inside HWOTA_BLN_Eng folder
HWOTA_BLN_Eng should be put inside the Tools folder of Huawei Multi-Tool v8
Make sure the path don't contain SPACE such as C:/Program Files
They are new update of the BLN-L22HNC675 (B520)
The newest one is : BLN-L22HNC675CUSTC675D2B520 (8.0.0.520) update on 2018.11.29
Search BLN-L22HNC675CUSTC675D here
You can upload the 3 zip on my pCloud (it's faster): ||__LINK__||
WARNING : On the first boot, wait 3-4 mins. The reboot to the EMUI 8.X can take some times
If after some minutes, nothing happen and you still on the blue Honor bootloop, try to wipe cache AND factory reset the phone via Huawei eRecovery or via TWRP (don't format data, only at the last resort but I think you have to reinstall the firware through HwOTA8 again). Have to be patient, it takes me 6-8 mins to reboot after wiping cache and data at the 2nd attempt.
- After successfully installed EMUI 8.X :
It's possible that you can't access TWRP, you have to reinstall TWRP Recovery through Huawei Multi-Tool (same step at the step 1/ Requirementsabove).
The tool will automaticcaly detect your device and propose you the BLN_TWRP_EMUI8.zip (press Flash Recovery_ramdisk with your phone open in android and allow the debugging connection - see 1/ Requirements for more informations.
Or you can download TWRP 3.2.X-0 (version 3.2.X only ! Other versions may not work, I didn't try it)
With this version, you will encounter some issue with TWRP. You can't wipe chache, or mount/unmount data for example, so some installtion through TWRP may not work, like for OpenGAPPS who maybe can't be installed when you want to try other Custom ROM like LineageOS. If you know how to install OpenKirin(LineageOS) on Honor 6x EMUI 8.X, feel free to share in this thread !
4/ Extend your RAM via SD Card
Spoiler: 4/ Extend your RAM via SD Card
If you succeed all those steps, you may right now see that your device maybe a little buggy, particularly when you open severals android application.
- For me, I used AParted available on the Play Store : ||__LINK__||
- This app require a rooted phone of course : Install Magisk ||__LINK__|| through TWRP Installation (Reboot to TWRP -> Install -> Install ZIP) or use SuperSU propose by Huawei MultiTool button installation
A PDF/Tutorial are available on the app inside, showing you the step to do with screenshot
WARNING : Save your data of your SD card before continue
You may not see big difference by increasing the RAM memory, it will just allow you to open more apps at the same times without crashing or lag
Summary of steps :
Tab CREATE -> press ADD 2 times (or more if you already have some partitions)
Set Part 1 as fat32 and give him his total storage
Set Part 2 as swap and give him his storage (will be for the RAM) (For me, I choose 2Go)
Click APPLY
Go to Tab TOOLS
Select Part 2 - FS: swap
Choose Swap in the drop down menu next to the button Apply
Press Apply
Watch a video (advertising if yo uconnected to internet)
Cancel the installation of AMemoryBoost
Click ON and OK to enable Swap Partition
Now you will saw the current RAM and the Swap memory
I wish my post can be helpful and I wish you can enjoy your new phone !!!
I can't wait to see new thread about an AOSP 11 on the honor 11 !
let us know which ROM you did try to install, and how you did solve. thx
Kentoto2021 said:
=> For future people who still want to know how I switch Honor 6x on EMUI 5.X to EMUI 8.X, I write just below the full step and problems that I met during this process (But I think there is already some thread that talk about this.
Click to expand...
Click to collapse
Below?
Kentoto2021 said:
I wish my post can be helpful and I wish you can enjoy your new phone !!!
I can't wait to see new thread about an AOSP 11 on the honor 11 !
Click to expand...
Click to collapse
thanks for this excellent and very complete guide. Hop too that @DarkJoker360 AOSP 11 system.img from Huawei P8 Lite forum will work as it did for march and July AOSP 10!!! I'll give i a try next week for sure :
After a succesfull debrand to BLN-L22 with the very fast way, I'm following your guide to step to EMUI 8, first of all thanks for providing files from your pcloud !!
Kentoto2021 said:
HWOTA_BLN_Eng should be put inside the Tools folder of Huawei Multi-Tool v8
Click to expand...
Click to collapse
You did use multi tool V8 to update to EMUI 8 ? Can see any signe of that in the guide you did follow . I guess it just replace the adb fastboot command .
All went fine for me, I'm now on very last EMUI 8 stock ROM for BLN-L22! thx
But of course TWRP flash is now an issue:
all TWRP recovery versions I fastbooted flash (3.1.1, 3.2.3, 3.5.0, all for bacon) sent me the same message error in fastboot: "FAILED (remote: partition lentgh get error)" . Apparently not EMUI 8 version .....
Oh nice wonderful !!! Happy it helps
I used the Multi Tools for the 3 step because it contains the adb and fastboot tools. But if you have it with the minimal adb software it will work also.
And if you set the adb folder to the windows 10 variable path system, I think you can put the HwOTA almost anywhere in the computer disk.
Yep indeed the twrp not work properly...
And still all my attempt to upgrade my OS with another method without the 3 zip (update, public, data) is not working
There is a workaround for custom recovery, I'll try it seriously and post back here
Kentoto2021 said:
Oh nice wonderful !!! Happy it helps
I used the Multi Tools for the 3 step because it contains the adb and fastboot tools. But if you have it with the minimal adb software it will work also.
And if you set the adb folder to the windows 10 variable path system, I think you can put the HwOTA almost anywhere in the computer disk.
Yep indeed the twrp not work properly...
And still all my attempt to upgrade my OS with another method without the 3 zip (update, public, data) is not working
Click to expand...
Click to collapse
U can try elite twrp,it worked perfectly fine for me
MAK7246 said:
U can try elite twrp,it worked perfectly fine for me
Click to expand...
Click to collapse
You mean this one:
[TWRP][3.2.1-0][EMUI5.X and AOSP][Decryption Support] For Honor 6X by HassanMirza01
Elite TWRP Project For Honor 6X DONOT COPY MY WORK, Ask for Permissions or Gather it yourself,,, This ROM is only for Firmwares based on EMUI 5.X only... /* * Your warranty is now void. * * We are not responsible for bricked devices...
forum.xda-developers.com
"for EMUI 5 only" on EMUI 8 ?
Djiban said:
You mean this one:
[TWRP][3.2.1-0][EMUI5.X and AOSP][Decryption Support] For Honor 6X by HassanMirza01
Elite TWRP Project For Honor 6X DONOT COPY MY WORK, Ask for Permissions or Gather it yourself,,, This ROM is only for Firmwares based on EMUI 5.X only... /* * Your warranty is now void. * * We are not responsible for bricked devices...
forum.xda-developers.com
"for EMUI 5 only" on EMUI 8 ?
Click to expand...
Click to collapse
Yep that is working fine!
MAK7246 said:
Yep that is working fine!
Click to expand...
Click to collapse
thanks, I'll use it for making a nandroid backup. Right afterward I'll install TWRP recovery from pretoriano80 (https://mega.nz/#!LLhBXSzY!3runNNoW9z1tOHSu-heIUhyy-4u8XHvc8rZMsn547so ou https://eu.dl.twrp.me/prague/) because I plan to try ton install @DarkJoker360 AOSP 11 for P8Lite.
Djiban said:
thanks, I'll use it for making a nandroid backup. Right afterward I'll install TWRP recovery from pretoriano80 (https://mega.nz/#!LLhBXSzY!3runNNoW9z1tOHSu-heIUhyy-4u8XHvc8rZMsn547so ou https://eu.dl.twrp.me/prague/) because I plan to try ton install @DarkJoker360 AOSP 11 for P8Lite.
Click to expand...
Click to collapse
Let me know if u are successful!

Categories

Resources