Develop Bugs

Resoldering/hot glue manuever micro usb

Ok, so my micro usb port broken. Even though that was the case, I could still bend it to make it charg.(Note I got this phone at the I/O conference last year, it broke almost immedietly, I didn't attend this years)
So then I got a replacement for 15$ (<< A LOT OF MONEY)
Resoldered it, but I was unsure of how stable it was, since there are only about 2 places it is soldered to.
I put cable in, and then I touch it quite a bit, and bam, whole connector falls of. Tried to repair, but then a bit of solder falls into the micro usb port, and it's like impossibe to get it out of, and I can't put the connector in...
Moar 15$
This time, I put a bit of solder, and then hotglue over the joints.
I though victory, until I realize I can't plug the connector in anymore, don't know why it wouldn't. Just won't fit(Maybe recieved bad, never checked)...
15$ more dollars now...
Anyone else successfully repair the micro usb port on these? I am going to just try a hot glue approach, with no soldering next try.
I don't have any warranty on this, as it was a gift after all.

When my port went out, the techs at Sprint told me that it was impossible to fix. I don't know if that's true, or if it was just cheaper to give me a new one.
Sent from my Evo using Tapatalk

I tried to repair my wife's with no luck. I eventually took the phone back to Sprint repair store and they replaced it no questions asked, although we had the warranty service. I did find a few articles online if you search google they should come up. I tried their methods but the problem I always had was I could not get the solder to flow well enough to bond to the connector. From the looks of the connector it is a flush mount which really makes soldering impossible unless you have one of the factory wave type solder machines.

Well, the connector I bought kind of goes thru the holes on the EVO. I will just simply hotglue it, no solder... should stay stuck hopefully.
I just hope the metal makes decent contact without more solder. Will report back when I fail/win. It would be awesome if I could just whine to Sprint for a replacement, but uh, no warranty + a gift phone =low chance
I bought this for others, http://cgi.ebay.com/MICRO-USB-CHARG...ps=63&clkid=9172696127650377355#ht_997wt_1139
Note the two feet sticking out, the generic ones don't have these, that would be hell to solder. I just hate the fact that these things are so fragile and expensive.

Got it soldered.
I had to have steady aim pro(perk for Cod4 )
With a very little bit of solder I got it sticking.
Then hot glued all over, like your average male's jizz amount of hot glue I used.(That's actually a good camparison before you get grossed out)
It works great.

USB jack replacement

The USB Mini-B jack (the USB port) on my LG P930 Nitro HD needs replacement. (This is partly because the battery life on the device is so short I have had to connect the thing constantly, using a variety of cables). The metal guides in the socket first appeared to separate from the male plug and are now a mangled mess, mostly at the back of the connector.
Does anyone have experience with do-it-yourself (DIY) replacement of this port?
The phone is rooted and running a custom ROM, so I can't take it for warranty.
I find many tutorials on screen replacement, but all I can find online are the replacement parts (such as this). Not a word, anywhere it seems, on replacing that port.
It's not easy to tell from either phone teardown video or the part itself, but it appears the socket is soldered to the board. . If that's true, I won't attempt it.
Also, does anyone have experience with the national myPhoneMD franchises regarding hardware repair ?

I can't speak to the level of complexity for doing this replacement, but I can tell you that indeed it requires soldering and not your run-of-the-mill soldering that you can do with any hobby soldering iron either. The 4 posts from that part you linked are just to hold the component in place...(If I'm not mistaken) there's still the actual USB connectors and they're likely surface-mount (magnifying glass and pinpoint soldering skills required here).
You might be better off with buying extra spare batteries and using apps like WiFi Explorer for accessing files on the SD Card remotely.

micro soldering definitely required
Namuna said:
I can't speak to the level of complexity for doing this replacement, but I can tell you that indeed it requires soldering and not your run-of-the-mill soldering that you can do with any hobby soldering iron either. The 4 posts from that part you linked are just to hold the component in place...(If I'm not mistaken) there's still the actual USB connectors and they're likely surface-mount
Click to expand...
Click to collapse
Interesting idea using batteries & WiFi ADB, but this device gets heavy field use and serves as my GPS on long trips. Plus, removing and replacing the Ballistic case is time-consuming. It's really too bad because after the better part of a year, I finally found a stable ROM where the battery would not drain in 2 hours or where the phone spent 1/4 of the time rebooting.
I found a close up photo confirming your observation. The signal lead connections are definitely smaller than my hobby-level solder skill can manage. The part is available from multiple suppliers, so someone somewhere has the skill set to replace it. I just hope it's not a three-week ordeal.

I feel your pain. My young son has been playing with my Nitro and he's nowhere near as anal as I am about not straining the USB cable when connected. Lately I've been noticing that I'm not getting good connections with all the USB cables I usually use (won't charge from the car adapter anymore. )
I'm glad you're even able to use the GPS for extended periods. I'm using a Hyperion fatty and CM10.1 ROM and when the car adapter *was* working, it couldn't keep my Nitro charged while using the GPS...If I couldn't get there within a couple/few of hours, I was screwed....And it's a high-capacity car adapter too.
...These guys need to get this magnetic USB connector to market, ASAP!!!
http://outsmartingtechnologies.com/project/magnetic-usb-connection/

Namuna said:
I'm using a Hyperion fatty and CM10.1 ROM and when the car adapter *was* working, it couldn't keep my Nitro charged while using the GPS...If I couldn't get there within a couple/few of hours, I was screwed....And it's a high-capacity car adapter too.
...These guys need to get this magnetic USB connector to market, ASAP!!!
http://outsmartingtechnologies.com/project/magnetic-usb-connection/
Click to expand...
Click to collapse
GPS: I have the same problem with battery longevity on trips. I could not run the phone continuously--even with the screen off--without going to 0%. On long trips there has to be a "refractory period" for the phone either off or in minimal consumption mode, if I want some battery left at the end of the journey or when I really need the GPS. I've tried a variety of DC chargers, but even the Stanley PC1A09 inverter powering the stock LG A/C adapter ultimately loses the battery fight. I am guessing that the inverter's output does not provide the A/C waveform as a wall outlet.
That magnetic connector looks great, but there would have to be a micro-format version.
None of the local repair shops in New Orleans, Louisiana will take on solder work at this scale. I ordered the $6 part but probably won't even try to install it, as I might destroy the board. Now I'm deciding between a local used locked phone, or a "new" unlocked phone on eBay. One particular seller with the best price has 99% positive reviews, but nearly all the negatives are from people who got used when they paid for new.

Have you tried bringing it to an actual AT&T store? I think we can give up the hope that they'll fix it under warranty, but at least they should be able to fix it at a cost...And if it ends up being cheaper than buying another Nitro used, then you've got a better deal.

My quit working I can charge it by putting something under the cord u might want give that a try it work for me
Sent from my LG-P930 using xda premium

stickman1981 said:
My quit working I can charge it by putting something under the cord u might want give that a try it work for me
Sent from my LG-P930 using xda premium
Click to expand...
Click to collapse
That's been my mode for a couple of months. I had ordered a Monoprice cable that didn't fit tightly, but just on my phone (all the other Androids in the house worked fine with it). In retrospect, that was an early sign of trouble.
I think the housing was stretched or distorted by an accidental cable yank months ago, and the socket just deteriorated from there. The short battery life made for more frequent connect-disconnect cycles on the hardware than I would have liked.
I ended up ordering a new replacement with a warranty that I'll probably trade with my son, and then he'll have a plan-protected phone to take to college. He's going to be in Canada and will need an unlocked phone (or else win the lottery). I'll take his locked AT&T phone for myself.
And I will take the bad-socket phone to the AT&T Device store in my area and see what it will cost to replace that port. If it's under $80-100, I'll probably go for it.

[Q] Replacing USB port

Seems my USB port needs replacing, I first thought I may have had some lint or something inside there as it wouldn't charge but after checking with a flashlight one of the pins had bent completely.
The only thing I can find for the original desire is eBay ID 380759842289
Can anyone confirm if this is right, or where I could purchase one from the UK.
Are they hard to replace? Would it just be the case of removing the 2 lower t5 screws, taking the antenna out of way and then what? Are they soldered on or ribbon cable?
Cheers

I had a similar problem, my device couldn't connect via usb but it was able to charge, so my first thought was the same as yours (about the lint). I tried to clean it and I found something like a little wire which was out of its place.
I ordered a usb port (about 1.50 euros) for that model and I followed this guide on youtube to disassemble the device /watch?v=8sYB_AM_jHE
You have to dissolder the old one and then solder the new which is a little bit tricky. It Worked!
For the replacement parts you can search on ebay for htc desire g7 its the same or use google you will find a bunch of them.

is it worth it to repair?

My microUSB port is messed up and will not charge by wire anymore. I got this device as a gift from my family. Do you think I should have it repaired?

If you are comfortable soldering a new one on then yes. If you are looking to buy a new daughter board then it is not worth fixing. Just buy a wireless charger

replacing charging port

My charging port is very temperamental. The cord needs to be a just the right angle etc. I'm thinking of replacing the charging port. On ebay there is a kit for $13 (ships from China). And there is also an ifixit guide to replace it. https://www.ifixit.com/Guide/Google+Pixel+3a+XL+USB-C+Port+Replacement/124576
Has anyone done this before? My main question is, do I need to use adhesive when I put the screen back in, and if not, how will the screen stay in?

mrtimo said:
My charging port is very temperamental. The cord needs to be a just the right angle etc. I'm thinking of replacing the charging port. On ebay there is a kit for $13 (ships from China). And there is also an ifixit guide to replace it. https://www.ifixit.com/Guide/Google+Pixel+3a+XL+USB-C+Port+Replacement/124576
Has anyone done this before? My main question is, do I need to use adhesive when I put the screen back in, and if not, how will the screen stay in?
Click to expand...
Click to collapse
I would just take it in and have somebody qualified do that kind of job

I agree, take it in. They have the proper tools and adhesives, plus you will usually get a small warranty on their work. Unless you're planning on making a hobby out of screen replacements lol.

Thanks. It seems crazy to spend $100 to have the phone fixed (thats the price I was quoted) when the phone's value is now around $200. But, spending $100 is better than breaking my phone.