Related
This guide is for you that have a new Xoom (WiFi only, US model) with Android 3.1 and want to
- get root access
- enable the external SD card unit
Please note that Android 3.2, which now is available for the US Wifi models, make this guide more or less obsolete. If your aim is to have root access, then there are probably simpler methods.
What you need to do can be encompassed in these following short steps (will be detailed later on) in the following order. Each step is required before you can proceed to the next one. However, make sure that you are very very careful and dont try to take any shortcuts. That may soft-brick your device, and you may have a difficult time to explain that to your wife ... You have been warned!
I strongly recommend you to read the entire guide before trying this. In fact, read it twice to ensure that you have understood everything. If there is wierd stuff that you dont understand, dont hesitate to ask. The reason for me writing this down is that I like to document what I have learned. This is to me an excellent way to ensure that I will remember what I just did. Another reason was that I could not find a single thread that encompassed all steps required. There are many different threads, but noone (that I could find) that really guides you from start to goal. So enjoy and good luck!
I would like to thank LandMaster and cam30era for helping out with advice during my initial trail-and-error session. I soft-bricked my device once and had big problems to get by point 4.3 (avoid overwriting of CWM), but with their encouragement I finally succeeded.
If someone else adapts this guide for the EU model or the 3G model, feel free to drop me an IM and I will update the guide for these devices too. Until then, this has only been tested on a WiFi only, 32 GB device bought in the US. If you brick your 3G or EU bought model, dont call me ...
0. Overview of the 6 required steps
1. Install Motorola USB drivers for your computers (for USB connectivity)
2. Install Java SDK and Android SDK tools (for adb and fastboot commands)
3. Unlock the device for flashing (allowing replacement of recovery and boot images)
4. Install a modified recovery image (ClockWorkMod recovery for Android)
5. Root the device (Allow r/w access to the device filesystem)
6. Flash a kernel that supports the SD card (SD card access, overclocking etc.)
Steps 1, 2, 4, 5 and 6 require that you download install, image and zip files needed for the flashing.
All this was performed on a Windows XP x86 SP3. Windows 7, Mac and Linux users will probably have to do some steps differently.
Update July 7: I have tested the procedure on Windows 7 x86 now and the procedure is identical to Windows XP.
1. Install the latest Motorola USB drivers
The installation file can be found here
http://www.motorola.com/Support/US-...tware_and_Drivers/USB-and-PC-Charging-Drivers
1.1 Install the drivers and ensure that your Xoom is recognized by the computer
2. Installation of development software
Java SDK 6 and Android SDK (for Honeycomb at least) need to be installed. You can find the installation kits here.
http://www.oracle.com/technetwork/java/javase/downloads/jdk-6u26-download-400750.html
http://developer.android.com/sdk/index.html
2.1 Install them as any other software.
2.2 What I had to do was to manually modify the PATH environment variable. I use Windows XP so I did that by right clicking on My Computer, choose Properties and select Advanced. Here I added the path to platform-tools and Tools
%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;C:\Program Files\Intel\WiFi\bin\;C:\Program Files\QuickTime\QTSystem\;D:\Java\Android-sdk\platform-tools;D:\Java\Android-sdk\tools
Note: If the Android SDK complains that the Java Dev Kit cant be found, just press Back and then Next again. Wierd, but that seems to do the trick ... go figure.
2.3 Test that ADB and FASTBOOT works. You should open a command window and go to your Android installation directory. Plug in your Xoom to your computer and write 'adb devices'. Your Xoom should now be listed like this
C:\Documents and Settings\Anders>adb devices
List of devices attached
0288414343813157 device
Did your device not show up? Make sure that you have USB debugging enabled in Settings / Applications / Development
3. Unlocking the device for flashing
This step will effectively erase the internal storage, including all your apps and settings. Use whatever backup you want to rescure important data before you start.
3.1 Power up and start the Xoom
3.2 Ensure that your device is fully recognized by the computer. A good sign is that the 'Portable device' dialog is activated on Windows when your Xoom has booted. The Xoom should also be seen in 'My Computer'. If not, go back to step 2 and double check your USB drivers.
3.3 Use the command 'adb reboot bootloader' to go into Flash mode
3.4 Use the command 'fastboot oem unlock'. This will trigger a dialog on your Xoom. Follow the instructions on the screen to complete the unlocking. I repeat, this *will* do a factory reset and all data will be lost!
3.5 Once unlocked, the Xoom will restart and work as normal, but now ready for step 4
4. Install recovery image (CWM)
Download the recovery image file and save it to your computer
4.1 Boot into flash mode with 'adb reboot bootloader'
4.2 Install your downloaded recovery image
C:\Documents and Settings\Anders> fastboot flash recovery recovery-Tiamat-R4c-100611-1150-cwm.img
4.3 Restart the device with 'fastboot reboot'. Timing is essential here, so be alert when the device restarts, or you will have to redo section 4.
4.4 Enter CWM with the following procedure
4.5 Once the Motorola logotype is shown, start counting to 3. At 3, press the Volume Down button. This should result in the text 'Android Recovery' in the top left corner. If it does not work, experiment with the timing ...
4.6 When 'Android Recovery' is shown press the Volume Up button. This should invoke the CWM recovery menu. If that works, then congratulations for reaching this far .
Here is a potential pitfall. If you are unable to enter CWM *before* the device boots into Honeycomb, then the newly installed recovery image will be overwritten by the system default recovery. There are ways to prevent this (see posts below), but I recommend you to redo step 4 instead of messing with removal of system files. But both methods would probably work. Experiment!
5. Rooting the Xoom
The root zip file is located here
5.1 You need to transfer the ROOT zip file to a working micro SD card. You can do this on a computer or cell phone, but the ROOT zip must be located in the root directory of the SD card.
5.2 Insert the now prepared SD card in the Xoom
5.3 Boot into recovery (as described in 4.3). Navigate using the volume buttons and press the power button to select the active option
5.4 Select 'Install ZIP from sd card'
5.5 Select 'Choose ZIP'
5.6 Navigate to the ROOT zip file with the Volume buttons and select it with the Power button. Confirm that you want to install it.
5.7 Everything should indicate success, so back out to the main CWM menu and reboot the device.
5.8 From Android Market, install the ROM Manager app and start it. If the rooting was successful, then ROM Manager should start without any complaints.
6. Flashing a new kernel that supports SD cards (and maybe more ...)
The kernel that I used is described here http://forum.xda-developers.com/showthread.php?t=978013
The kernel zip file is located here
6.1 This step is identical to 5, but swap the ROOT zip towards the KERNEL zip. For simplicity, you may want to prepare the SD card with both zip files at the same time in step 5.1 ...
Looks great. You just might want to give credit to LandMaster and cam30era, too.
Also is this for just USA or all, cos many people brick there xoom if its just for USA only
okantomi said:
Looks great. You just might want to give credit to LandMaster and cam30era, too.
Click to expand...
Click to collapse
Of course, done
juDGEY2k10 said:
Also is this for just USA or all, cos many people brick there xoom if its just for USA only
Click to expand...
Click to collapse
This is only tested on a US device. OP updated.
Will this wipe all USER data?
Also, is the location of the zipped root file fine? the title says "[BOOT] Wifi-Only Charge Light Off".
I only see one problem, you have recovery before boot.img. If you flash the recovery, without a rooted boot.img and happen to boot into honeycomb, it will erase your recovery and load stock. So you can remove /system/etc/install-recovery.sh and /system/recovery-from-boot.p or flash the boot.img BEFORE rebooting out of recovery.
BrokenPixel said:
Will this wipe all USER data?
Also, is the location of the zipped root file fine? the title says "[BOOT] Wifi-Only Charge Light Off".
Click to expand...
Click to collapse
When you unlock your Xoom, it will wipe all user data.
bwcorvus said:
I only see one problem, you have recovery before boot.img. If you flash the recovery, without a rooted boot.img and happen to boot into honeycomb, it will erase your recovery and load stock. So you can remove /system/etc/install-recovery.sh and /system/recovery-from-boot.p or flash the boot.img BEFORE rebooting out of recovery.
Click to expand...
Click to collapse
You're right. I rooted 1st and flashed CWR later. I then used brd's method to update to 3.1, re-root and flash the new bootloader and kernel. So there is a step missing after Step 3. I'm sorry, I don't remember exactly how to do this from HC 3.1. (meaning what files to use) as I was on HC 3.0 at the time.
BrokenPixel said:
Will this wipe all USER data?
Also, is the location of the zipped root file fine? the title says "[BOOT] Wifi-Only Charge Light Off".
Click to expand...
Click to collapse
Yes it will. Read 3.4 again, it will do factory reset.
The root file may vary from case to case, but the procedure is the same AFAIK. I used the one that "charge light off"... There are probably others too.
bwcorvus said:
I only see one problem, you have recovery before boot.img. If you flash the recovery, without a rooted boot.img and happen to boot into honeycomb, it will erase your recovery and load stock. So you can remove /system/etc/install-recovery.sh and /system/recovery-from-boot.p or flash the boot.img BEFORE rebooting out of recovery.
Click to expand...
Click to collapse
This is true, and I will update the OP to reflect that.
So has anyone followed this guide successfully yet? I don't really want to be the first...
yordikins said:
So has anyone followed this guide successfully yet? I don't really want to be the first...
Click to expand...
Click to collapse
Hi
I did!. And you know that someone gotta be first (actually second). Why not take the credit?
pingvinen said:
This is true, and I will update the OP to reflect that.
Click to expand...
Click to collapse
So I'm guessing the OP has been updated? I think I'm ready to dive in
Sent from my Xoom using XDA Premium App
Abracastabya said:
So I'm guessing the OP has been updated? I think I'm ready to dive in
Sent from my Xoom using XDA Premium App
Click to expand...
Click to collapse
Instructions are good to go. Just make sure that you don't reboot after flashing recovery, and before flashing boot image. If you do, by mistake, no harm done. You will just have to flash recovery again.
cam30era said:
Instructions are good to go. Just make sure that you don't reboot after flashing recovery, and before flashing boot image. If you do, by mistake, no harm done. You will just have to flash recovery again.
Click to expand...
Click to collapse
Sounds good and thanks B-)
Sent from my Xoom using XDA Premium App
Tnx . Very help full .
I don't know but ROM Manager just isn't budging showing any signs of root... or Superuser (+Elite)... or MarketEnabler...
I don't know, I'm kinda lost here. Let me retry (for the tenth time).
rmcsc said:
I don't know but ROM Manager just isn't budging showing any signs of root... or Superuser (+Elite)... or MarketEnabler...
I don't know, I'm kinda lost here. Let me retry (for the tenth time).
Click to expand...
Click to collapse
Try again, and remember that timing (3 seconds) are key to success ...
I'll retry being more precise. I do get into Recovery and I flash the file mentioned. It seems it flashes correctly but when I boot into the OS, there's no signs of root anywhere.
I'll update in a few. Thanks!
Sent from my T-Mobile G2 using Tapatalk
Hi together,
since my home button is broken, i need to flash the Stock-ROM (sending in the device for repair).
This not an easy task, since a cannot use CWM to flash, as the borken button is needed there.
ODIN would be another way, but i could not get it working under Win 8.1 x64 (tried two different usb cables, various driver versions, signature check disabled etc.. nothing worked for me - really hate this **** now )
I managed to flash a Touch Recovery via Terminal though, so i can flash zip's again.
Is there any flashable version of the european Stock-ROM? I found onr, but links are dead there .
I greatly appreciate any help.
Greets
//EDIT: Ok, seems as its actually not possible to use ODIN under Win 8.1 atm, due to unsolved driver issues.
Ok, solved. i finally installed Win7 on a seperate partition and flashed it with ODIn thiss way.
Btw: It seems to be possible to get in Download or Recovery Mode when you are stuck in Bootloop:
Enter
Code:
adb reboot download
or
Code:
adb reboot recovery
when your phone is not bootet, but battery is loading (battery animation visible, so it actuaööy has bootet, but not the ROM itself, only bootloader.)
Interestengly, this works, while calling the commands in the adb shell itself, does only work when you are rootet (which is likely not the case e..g. when you go back to stock rom, and end in a bootloop after flashing it).
Greets
EDIT: included rough procedures for OEM unlocking, and updated link to recovery-verified.img (Sorry for uploading the wrong file ><)
Hi all bv9000 pro Users!
Recently I went on a journey to root this awesome rugged phone with one purspose: to remove that F*@(#&$ god awful loud annoying sound triggered by the OS when you use a camera app to take a picture + the boot startup sound (A bug blackview hasn't gotten around to fixing).
I successfully managed to port TWRP 3.1.1 from the Blackview bv8000 Pro and run it on the Blackview bv9000 Pro-f!
I've then managed to flash in Magisk to gain root access.
DISCLAIMER: I do not take responsibility for any bricked phones caused by the process, do so at your own risk (yadayadayada).
NOTE 1: Although I've got it running on the bv9000 Pro-F, this image should also work for the non-fullHD version, if someone can test this I'd be happy.
The link to the stock ROM (with the modified recovery img) can be found in the post below.
NOTE 2: No need to download anything other than what I've listed, Magisk is included in my custom recovery to circumvent the need to load the devices encrypted storage (or any other external storage) nothing stops you from mounting external usb storage.
What you'll need:
- USB Mouse (As there is no touchscreen input support, your device should have come with a usb-c otg cable so there's no problem here!)
- MediaTek SP Flash tools (I'd recommend the latest version) https://spflashtool.com/
- unlocked bootloader (You should be able to do this via the developer settings -> unlock OEM Bootloader)
EDIT: To unlock the boot loader, do the following:
1) Go to settings -> unlock OEM Bootloader (tick)
2) plug your device in (assuming you have ADB installed), use adb to access fastboot via. command prompt:
"adb reboot bootloader"
Then once the device is rebooted into fastboot mode
"fastboot oem unlock"
KEEP IN MIND THIS WILL REMOVE ANY FILES, so back them up
- I've done this with windows, but you should be able to repeat with linux no problems!
- A little patience
Pre-preparation:
First install any updates and back up your data (it's just easiest to use the google cloud backup as restoring becomes easy as pie, updating also fixes the setup wizard crashing on first setup). This is necessary because OTA updates cannot be performed with TWRP recovery, and flashing TWRP before doing OTA updates will flick the device into a recovery boot loop.
Install the SP Flash tools, and the MediaTek VCOM Drivers
(I won't link the specifics here, a quick google search should be able to help you, just note you might need to disable driver signature enforcement)
Two options for flashing:
1)
My Full Stock ROM already pre-prepared for flashing:
Patched ROM
No need for extra prep here! you should just be able to load the scatter
2)
My custom patched TWRP stock rom: recovery-verified.img
Blackiew's stock rom: stock rom
- Download the stock rom, backup the recovery-verified.img in the R06 folder, and then replace it with my custom patched TWRP stock rom (file name should be the same).
- Run "CheckSum_Gen.exe" once you replaced the file, it will generate the necessary checksum to allow SP flash tools to successfully flash recovery.
Once you've done with the pre-prep, switch off your device, take a deep breath and you're ready to go!
Steps!
1) Load up SP Flash Tools, select the android scatter file you've downloaded in the R06 folder
2) Select Download Only (I MEAN IT, FORMATTING WILL REMOVE YOUR IMEI AND RENDER THE PHONE USELESS)
3) Deselect everything but recovery (You only want to flash this)
4) Hit download
https://pasteboard.co/HkufwZZ.png
5) Hold volume up + power and plug in your phone, keep the volume up button held
6) very quickly the flash should be complete, and you should be greeted with a big ol' green tick to verify
https://pasteboard.co/HkuiTBB.png
7) Once you're done, remove your USB cable, plug in the OTG then we proceed to flash magisk
8) Hold power + volume up until you reach the bootloader, then use the menu to select recovery
9) You *should* be greeted with the TWRP recovery screen (Which is great success! )
DON'T PANIC IF YOU CANNOT USE THE TOUCH SCREEN, the kernel I've patched is missing this, seems the driver is different between touch screens, just plug in your OTG mouse to continue from here!
10) Use your mouse to first hit cancel, we don't need to decrypt the user data storage.
11) But oh no! it's all in Russian (no problem, Next step sorts that)
12) Use your mouse to navigate the menus as shown here to change to English! (or your preferred language) Change Language
13) Click install, then navigate up folder levels until you are in the root directory
14) scroll down and click on Magisk.zip, install it, allow it to install any apps as system apps (because this will then install to the system image, not the userdata)
15) reboot the phone (if it hasn't rebooted already)
16) You should be able to boot into your usual phones OS, if you don't see Magisk listed in your phone apps, just download it from here:
Magisk Manager
17) Congratulations! You should have complete root access :laugh::laugh::laugh:
Feel free to express your thanks, or list any problems you have, but keep in mind my studies take all my life, so I may not be able to help with all the problems you have
Congrats! Would it work on the BV9000 HD version?
Hi!
From what I've seen they both run the helio p25 chip
(Just a difference in RAM size) so it should.
You're more than welcome to try.
Just keep a backup of the original ROMs recovery. If something goes wrong during the boot to recovery you can easily re flash
hi i tried both optinos but they didn't work for me
I tried the first and the second options and it was showed me same error:
ERROR: STATUS INSUFFICIENT_BUFFER(0XC0010007)
I tried download only, format all and download, if i install original ROM its installing without problems!
In settings-> developer options -> OEM unlocking is enabled
can someone give me tips if I'm doing something wrong. thanks
My phone is Blackview BV9000PRO-F
Hello,
i have the blackview 9000 pro Hd (not full hd)
i first tried your prepared patched rom = not working (get erorrers in step 6)
then i chose step 2 and i was thinking to use the stock rom from the NOT full hd rom
now i get a green screen from the flashing: but after rebooting in recovery nothing happens, just normal reboot then
perhaps this is not so clair for me:
- Download the stock rom, backup the recovery-verified.img in the R06 folder, and then replace it with my custom patched TWRP stock rom (file name should be the same).
- Run "CheckSum_Gen.exe" once you replaced the file, it will generate the necessary checksum to allow SP flash tools to successfully flash recovery.
the file name you posted here " My custom patched TWRP stock rom: recovery-verified.img" is ramdisk-recovery.img
i replaced the ramdisk-recovery.img... it is not clair need to replace recovery-verified.img to?
>I tried the first and the second options and it was >showed me same error:
>ERROR: STATUS INSUFFICIENT_BUFFER(0XC0010007)
> tried download only, format all and download, if i install >original ROM its installing without problems!
>can someone give me tips if I'm doing something wrong. >thanks
>My phone is Blackview BV9000PRO-F
Hi, you need to unlock the OEM bootloader, if this is still locked it will prevent the flashing of custom ROMS.
I might've missed this step, will update post as necessary.
>
dingsje said:
Hello,
>i have the blackview 9000 pro Hd (not full hd)
>i first tried your prepared patched rom = not working >(get erorrers in step 6)
>then i chose step 2 and i was thinking to use the stock >rom from the NOT full hd rom
>now i get a green screen from the flashing: but after >rebooting in recovery nothing happens, just normal >reboot then
>perhaps this is not so clair for me:
>- Download the stock rom, backup the recovery->verified.img in the R06 folder, and then replace it with >my custom patched TWRP stock rom (file name should >be the same).
>- Run "CheckSum_Gen.exe" once you replaced the file, >it will generate the necessary checksum to allow SP >flash tools to successfully flash recovery.
>the file name you posted here " My custom patched >TWRP stock rom: recovery-verified.img" is ramdisk->recovery.img
>i replaced the ramdisk-recovery.img... it is not clair >need to replace recovery-verified.img to?
Click to expand...
Click to collapse
Hi,
I've uploaded the wrong file, the uploaded file should be recovery-verified.img.
I'm uploading a new file and will correct the link now,
Please accept my apologies ><
hyperlethalvector92 said:
>I tried the first and the second options and it was >showed me same error:
>ERROR: STATUS INSUFFICIENT_BUFFER(0XC0010007)
> tried download only, format all and download, if i install >original ROM its installing without problems!
>can someone give me tips if I'm doing something wrong. >thanks
>My phone is Blackview BV9000PRO-F
Hi, you need to unlock the OEM bootloader, if this is still locked it will prevent the flashing of custom ROMS.
I might've missed this step, will update post as necessary.
Click to expand...
Click to collapse
I already did this step:
Enable developer options-> OEM unlocking is enabled
Is that enough for this MTK phone to be unlocked the bootloader ?
And tried the both options but the results are same.
I have been unlocking bootloaders on many phones but first time MTK phones. If i try with adb commands it recognize when is in the android with command adb devices and show my device but if I try reboot bootloader and check in device manager in windows its show its connected and drives are correct but if i try to show the devices, it doesn't show any device connected
Hi,
You need to install fastboot drivers once it's in bootloader mode,
then use fastboot, not adb.
"fastboot oem unlock"
Then follow instructions.
simply doing settings -> oem unlock won't unlock the bootloader, it allows you to do so later via. fastboot
Check the original post, I've added the extra instructions sorry about the confusion!
Thanks a lot. I finally succeeded to unlock the bootloader and root my phone and install the magisk.. I did without use your rom just I unlocked the bootloader and install your twrp file and after in the recovery mode i format the data and istall magic and i still have the last updated android.
I hope this it ill help to other people. Cheers
zlatkomas said:
Thanks a lot. I finally succeeded to unlock the bootloader and root my phone and install the magisk.. I did without use your rom just I unlocked the bootloader and install your twrp file and after in the recovery mode i format the data and istall magic and i still have the last updated android.
I hope this it ill help to other people. Cheers
Click to expand...
Click to collapse
I'm glad ^______^
Enjoy your rooted phone
I used this video to root my bv9000 pro hd
much easier than this above, i think it works to on bv9000 pro fhd
https://www.youtube.com/watch?v=c48ISLPjn4Q
Congratulations .... I need a tip,.
And, brother, thank you very much. Worked perfectly.
But first I would like to get you a tip ..
One of the main reasons I have done all this complicated process was to be able to disable the crap of the loud music that plays when the device is started.
I want complete silence at startup.
How do I disable this ****?
Code for Huawei mobile Wi-Fi e5577s-321
Pls help unlock my Huawei mobile Wi-Fi e5577s-321
Imei
860782038163889
TWRP looping after OTA update
My dear, the procedure worked very well, until an OTA update was downloaded.
You are now looping on TWRP. How do I get out of this?
:crying:
help!
i missed to run wireless software update,so ROM clashed.
How can i re-install custom ROM?
mackie_ma said:
help!
i missed to run wireless software update,so ROM clashed.
How can i re-install custom ROM?
Click to expand...
Click to collapse
Hi guys, lemme apologize for disappearing, life and whatnot!
For those stuck in a TWRP boot loop, simply restoring the original recovery then restarting the phone will be enough to fix the problem.
(Actually you really don't need TWRP after the phone is rooted, maybe I should update the guide?)
Many Thanks
First off, thank you for your hard work. Loved the "**** it we have an OTG cable let's use it" haha. It works fine for me.
Second, do you happen to know if someone has ported Oreo on our bv9000 ? Or do you know of any ETA ?
Thanks again,
Cheers
Anyone tried on the BV9000 Pro? Don't think mine is 'F' OR 'Fhd'.... I must have first model brought out...
Ugh.. Windows and Drivers?!?!
I keep getting Driver not Recognized in Windows 7 Pro X86.
I installed the latest vcom/usb drivers, in legacy also. No Go.
I installed from several other sources the drivers, including the Automatic Mediatek driver install. No Go.
So if anyone has a tip for me, please let me know because once more Windows is proving itself ridiculous. I can't even get to the storage of my phone. Did something change with a Windows Update that it's not allowed anymore?
I put my BV9000 Pro in OEM Unlock and USB Debugging. I backupped everything. My phone is ready for it. It's as ready as Amy having coitus with Sheldon for the first time.
Hello everyone, after struggling for a few hours I managed to finally disable force encryption in my phone (so that TWRP could backup the data partition).
I'd like to write a quick list of what I did in the form of a guide to unlocking the bootloader, installing TWRP and getting root with Magisk. I'm just a user, not a developer and this guide is brief, it's not a detailed tutorial and does not include trivial steps (like how to install drivers for your OS).
Warnings: Although small, there is always the chance this bricks your phone. I take no responsibilities.
This will factory reset your phone so back up everything before you start.
My phone is Lenovo S5 (K520) Global version (see screenshot) I don't know if this will work for other firmwares.
Prerequisites:
Install Phone, ADB and Fastboot drives. You can get ADB and Fastboot binaries from here:
https://forum.xda-developers.com/showthread.php?t=2588979
Download this archive:
http://www.mediafire.com/?4dcvzw1hdmzfn10
It contains all the files used in this guide.
Alternatively, download all the files used from their sources.
You will need an SD card or a USB flash drive with an OTG adapter.
Copy the following files to it:
A. "Disable_Dm-Verity_ForceEncrypt_12.16.2018.zip"
(Downloaded from http://forum.xda-developers.com/showthread.php?t=3817389 )
B. "Magisk-v18.0.zip"
(Downloaded from http://forum.xda-developers.com/showthread.php?t=3473445 )
C. (optional) "\stock\boot.img"
(Downloaded from the global firmware @ 4pda)
If you chose to use Micro SD card, you can insert it now.
Note: I know there is a way to push these files directly to TWRP from PC through USB instead of using SD Card/Flash drive but I've never tried it.
Lets start:
1. Go to 'Settings>About phone' and tap on "Lenovo version" several times until developer options are enabled.
2. Go to 'Settings>System>Developer options' and enable "OEM unlocking" (Note: for me this option was greyed out and I had to connect to wifi and wait for a minute or two).
Optional: Enable "USB debugging" if you wish to enter fastboot via ADB.
3. Turn off the phone and press and hold 'Volume down'+'Power' buttons until you see "fastboot mode" on the phone screen (alternatively, don't turn off the phone and instead enter fastboot mode via ADB (adb.exe reboot bootloader)).
4. Connect the phone to the PC via USB and open a command prompt in the location that you installed fastboot binary to.
Type (after each command press enter):
Code:
fastboot devices
To verify that the phone is recognized. And if it is type:
Code:
fastboot oem unlock
Now on the phone LCD navigate to "Yes" with volume buttons and press power to select it.
Your phone will factory reset, this will take a few minutes. Let it finish.
5. Put the TWRP image in your fastboot path. I used "recovery-twrp-3.2.3-crn-seoul(v3.2.3-1).img" downloaded from this URL:
https://forum.xda-developers.com/android/development/lenovo-s5-k520-twrps-t3863860
But I included 2 more files that I found (I did not try them).
6. Enter fasboot mode again and type:
Code:
fastboot flash recovery recovery-twrp-3.2.3-crn-seoul(v3.2.3-1).img
(Substitute "recovery-twrp-3.2.3-crn-seoul(v3.2.3-1).img" with the recovery filename of you choice)
7. If successful, disconnect the USB cable and enter Recovery mode, do not turn off or reboot the phone because upon restart the phone will revert to stock recovery (I.E. delete TWRP).
To enter Recovery mode press and hold 'Volume down'+'Power' buttons until you see "fastboot mode" and from there choose "Recovery mode" with the volume buttons and confirm with the power button.
(Alternatively, you can try holding 'Volume up'+'Power' to directly enter Recovery mode but I found it a little finicky)
8. In TWRP, swipe to allow changes. Press cancel when asked for a password to decrypt data.
If you chose to use a USB flash drive with an OTG adapter, connect it and mount it (Mount>usb-otg).
9. Go to Wipe>format data, type "yes" and confirm (if you have any data like installed apps, contacts etc., it will be deleted).
10. Go to Install and install "Disable_Dm-Verity_ForceEncrypt_12.16.2018.zip".
The files will be in (/external_sd/ or /usb-otg/).
11. Install "Magisk-v18.0.zip"
Important note: If you want to keep encryption (if you don't care if TWRP can't access /data/) and just obtain root, skip steps 9 and 10.
12. Reboot to system and wait for a few minutes for the initial setup.
If for some reason boot fails (nothing happens after 10 minutes) and you can still enter TWRP (hold 'Volume up'+'Power'), then you can revert the changes by restoring the stock boot image (TWRP>Install>Install image>boot.img - put a checkmark on "boot").
If this worked for you, please tell us by replying to this thread.
Thanks a lot man. This phone is a beast in quality/price when talking about hardware. Costs a bit more than 100€ and has the same hard than others at 180-200€ at least. Bad thing is software but with TWRP and root everything is possible . Just found what project treble is, amazing possibilities. Can't beliebe nobody replied yet to yor post. Its a great guide and you show all the sources from where your downloads come. As you said in another thread its better this way so people can trust your content more:
C4lculated said:
I also wanted to root but I didn't want to run a bunch of unknown programs (from XN Logos), so I managed to install TWRP and root with magisk. I wrote a guide on how to do it:
https://forum.xda-developers.com/ge...ide-lenovo-s5-k520-twrp-root-decrypt-t3882402
Click to expand...
Click to collapse
I am yet waiting for my Lenovo S5 to arrive but I will give this guide a try. I was about to follow XN logos (stupdroid) guide/software but I prefer yours. Just one question... have you checked whether the TWRP v3.2.3 (latest) from dmilz make proper working backups? Can I trust that a full backup will be loaded correctly after installing any unofficial ROM, to go back to stock if necessary? I made once the mistake of relying a TWRP and later I found out that one was ok for flashing but didn't create working backups. I asked him also the same question, but I guess you also tried yourself to make a backup and restore from it using TWRP.
Next step will be to flash an Android 8.1 or 9 GSI rom (did I already say I'm amazed by GSI/project treble roms? just found about them last days). I will update you about my luck following your guide
does anyone enable lte bands, 4 and 28?
just bought this phone, currently on shipping..
I'll first try with twrp + aosp 9 GSI
Hi man, have you upgrade to gsi
acost91 said:
Thanks a lot man. This phone is a beast in quality/price when talking about hardware. Costs a bit more than 100€ and has the same hard than others at 180-200€ at least. Bad thing is software but with TWRP and root everything is possible . Just found what project treble is, amazing possibilities. Can't beliebe nobody replied yet to yor post. Its a great guide and you show all the sources from where your downloads come. As you said in another thread its better this way so people can trust your content more:
I am yet waiting for my Lenovo S5 to arrive but I will give this guide a try. I was about to follow XN logos (stupdroid) guide/software but I prefer yours. Just one question... have you checked whether the TWRP v3.2.3 (latest) from dmilz make proper working backups? Can I trust that a full backup will be loaded correctly after installing any unofficial ROM, to go back to stock if necessary? I made once the mistake of relying a TWRP and later I found out that one was ok for flashing but didn't create working backups. I asked him also the same question, but I guess you also tried yourself to make a backup and restore from it using TWRP.
Next step will be to flash an Android 8.1 or 9 GSI rom (did I already say I'm amazed by GSI/project treble roms? just found about them last days). I will update you about my luck following your guide
Click to expand...
Click to collapse
Kindly drop the procedure am hitting brick with all the method i used .????????
Stock firmware lenovo k520
I have tried your method on ROM that is based on China and also globally, and TWRP was successfully installed, and I have also tried several Rom GSI, and only AOSP Extended is successful, but with Bluetooth bugs it cannot be turned on, if others want flash files and stock firmware for k520, just let me know, thanks.
Working on S5 Pro too?
Hi! Can it work on S5 Pro too? I really want to root this device and I don't find out a way to get this happening. Thanks!
Does this work for s5 pro l58041?
Thanks
B4ph0 said:
I have tried your method on ROM that is based on China and also globally, and TWRP was successfully installed, and I have also tried several Rom GSI, and only AOSP Extended is successful, but with Bluetooth bugs it cannot be turned on, if others want flash files and stock firmware for k520, just let me know, thanks.
Click to expand...
Click to collapse
Hi! Sorry for offtopic!
Could you please PM me the link on AOSP extended image which you installed. Thank you!
Hello! Did somebody managed to install GCAM to Lenovo S5? I'm trying and I can;t do this, magisk modules are not loading...
so far I've used 2 alternative rom and works fine, aosp & octopus os, especially octopus os
I need some help..
Did anyone had lenovo s5 persist.img..
I lost my persist afer flashing global rom.208st via qfil..
I check the rom has no persist.img
Please visit to https://youtu.be/wbpV59kutJM for tutorial flash and upgrade Lenovo S5 in YouTube
hello guys, i always get into download mode,after press reboot system (twrp), any solution for my problem ?
has anyone achieved unlocking bands in this phone?
Please port miui 11 9.10.30 mi-room pie 9.0 redmi note 4x SD625 to lenovo S5.
https://megaroms.net/miui-11-9-10-30-stable-port-for-redmi-note-4-4x/
https://sourceforge.net/projects/miui-ports.whats-new.p/files/mido/miroom/
After unlocking bootloader, is there anyway to remove the hideous "software can't check for corruption" warning? Thanks.
---------- Post added at 01:44 AM ---------- Previous post was at 01:39 AM ----------
Suryo75 said:
hello guys, i always get into download mode,after press reboot system (twrp), any solution for my problem ?
Click to expand...
Click to collapse
This means no rom is installed in your phone. Either you accidentally wipe system in twrp, or the rom is corrupted.
Download the deodexed stock rom below and flash with twrp. Should fix your problem.
https://drive.google.com/open?id=13tRqo5eSpRiVJwKiA-iSj2GyIF353ATQ
jychung93 said:
After unlocking bootloader, is there anyway to remove the hideous "software can't check for corruption" warning? Thanks.
---------- Post added at 01:44 AM ---------- Previous post was at 01:39 AM ----------
This means no rom is installed in your phone. Either you accidentally wipe system in twrp, or the rom is corrupted.
Download the deodexed stock rom below and flash with twrp. Should fix your problem.
https://drive.google.com/open?id=13tRqo5eSpRiVJwKiA-iSj2GyIF353ATQ
Click to expand...
Click to collapse
thank you i'll try
Could you plz make tutorial about getting back to stock unroot...thx
Twrp gone
Hello sir thank you for this wonderful tutorial,
But I have a problem , after booting to TWRP , then boot to system after that when I try to go back to recovery mode TWRP , twrp is gone , stock recovery back
EDIT:SOLVED -- READ BELOW:
I finally got it flashed by following a few guides here which I will link, and try to break it down easier for someone else to come across and follow. I thought I bricked my phone (flashed LineageOS then rebooted, phone did not show anything on screen, full black screen) but after following a few guides I got it solved.
If you get bricked, or just want to follow a clean perfect install, please start below (Skip to step 2 if you are starting fresh, if you have soft-bricked your device start from step 1)
1. Bricked it and had to execute QDLoader 9008 fix again.
Tutorial is easier than it looks, do not fear, if you have soft-bricked your device and see a black screen, go ahead and go through the qdloader brick solution.
2. From factory recovery updated to Version WW-16.1220.1909.193.
If you have started fresh, I would highly recommend updating to the more updated firmware first. For me this worked, and I suggest updating to get a more current kernel, which may play better with Lineage OS install. To install a newer stock firmware linked above, download the ~2GB Firmware above, and save it to your Minimal ADB / Fastboot folder. Power off your device, after it has been successfully restored (if you bricked it) or you want to start off fresh and get the install right the first time. With your device powered off, Hold Volume UP and then Hold Power Button until the Fastboot menu appears. Use your volume keys to select Recovery, then press Power button to enter the STOCK Recovery (we are still on stock firmware with stock recovery). When in stock recovery select install from ADB. We are going to push the install via ADB (I tried dragging the firmware to the internal and selecting install ZIP and that didnt work).
Go into your Minimal ADB / Fastboot folder on your computer and open command prompt by holding Shift+Control and Right clicking and then selecting open command prompt here.
Now, enter the following command in the command prompt and hit enter:
adb devices
This command will show if any fastboot device is connected. If it doesn’t show, then please check the drivers are installed properly and try again.
If your device is listed, then type the command given below and press enter:
adb sideload File_name.zip
^^This will be the ~2GB Firmware file downloaded above
Wait until the installation process completes.
Once the installation process is complete, restart your device.
Done. You have successfully upgraded the Asus ZenFone 6 to the newer firmware, please continue.
3. Downloaded OTA 16.1220.1909.193 to 16.1220.1909.194, renamed it to UL-ASUS_I01WD-ASUS-16.1220.1909.194-1.1.1-user.zip and placed into root of internal memory.
When I disconnected USB cable (or rebooted, not sure), I was prompted with update notification. I have updated it. Either way, reboot your device if you don't see the notification, and look in your notifications to see something saying: System Update Detected Proceed with Update - and select it and update.
4. Now that your phone is 100% Updated with the newest firmware, let's follow another guide I found here:
I assume you're on a fresh Android 9 stock ROM, or just finished restoring your phone with the Flashall_AFT.cmd from this tutorial.
You should at least boot once on the system, and disable any PIN or password to unlock your phone (hence putting a default password for the FBE).
Download the latest OFFICIAL TWRP.x.x.img (which we'll use to boot on it), and it's installer to install it later (TWRP.x.x.zip) if you want to use it.
LineageOS installation steps :
Reboot to bootloader (=fastboot mode), connect to your PC and boot on TWRP :
Command:
fastboot boot TWRP.x.x.img
Once on TWRP, you can see that we're on slot A (Menu > Reboot). Now go to wipe > factory reset and then wipe system (technically I suspect this only wipes slot A, but do it anyway, don't worry about the errors!)
Now go to Install > flash the newest official LOS_latest.zip. What happens here is that the LOS installer will flash LOS on the inactive slot (slot B in our case). And will also install the LOS recovery (on both slots it seems).
Reboot to recovery : your phone automatically switches slots and will boot the LineageOS recovery (Don't fear, we don't need TWRP right now, just go along with this step) on slot B.
On the LineageOS recovery, do factory reset (which seems to be a full /data format in fact, thus removing any previous encryption AND all your data on internal storage). If you want to use Magisk, go to the recovery's install menu and sideload it now
Use code:
adb sideload Magisk-v20.3.zip
Now reboot to system. It might take a while (one or 2 loops in my case), but your phone should boot, or in some cases will end up on LOS recovery asking for a 'factory data reset' (then do it and reboot again).
Once booted on your LOS rom, you can define a pin or password to lock your phone (that'll be the FBE decryption password).
Now if you want to use TWRP, reboot to bootloader and boot again on TWRP.img (step 1)
From TWRP > Install > flash TWRP.x.x.zip (that is, the TWRP installer). It installs on both slots by default. If you had installed Magisk, you have to flash it again (because anything modifying the boot.img - like the TWRP installer in our case - will erase it).
You can now reboot to system and enjoy LOS
Thanks for the nice documentation. I've recently also struggling with installing a custom ROM and this clears some things up.
Wanted to ask, if you also have the audio issue that 1) callers hear an echo of themselves, and 2) the bottom speaker is active when receiving a call?
Thanks.
abprie said:
Thanks for the nice documentation. I've recently also struggling with installing a custom ROM and this clears some things up.
Wanted to ask, if you also have the audio issue that 1) callers hear an echo of themselves, and 2) the bottom speaker is active when receiving a call?
Thanks.
Click to expand...
Click to collapse
Haven't actually put my sim in yet to make calls, will let you know later today, sorry about the delay!
I had previously attempted this a number of months ago, and managed to soft brick my Zenfone 6 several times, eventually kind of giving up and just using the stock firmware.
I tried again back on Memorial Day in the US. This time around, I bricked it hard. Could not get device to power on in any fashion. PC would not "see" USB connection at all.
I returned it to ASUS for service, and they've charged me a little over $200 to repair it. The only problem they noted was, "Device is rooted/unlock". So I have no way of knowing if their diagnosis is based on actual inspection of the device, or if they're just replacing the SOC on the basis that I used their official bootloader unlock tool, thus registering my phone's S/N.
Just a little caveat emptor for anyone attempting to use this guide. I was able to get TWRP to load, and succesfully updated the stock firmware, but any and all attempts to load the Lineage image failed.
Eventually one of them soft bricked my phone as before, and I think my mistake was interrupting the soft brick rewrite procedure by prematurely unplugging my phone from the PC.
I had a similar issue: Bricked and totally unresponsive phone (or so I thought until I realised the screen was flashing very faintly when I switched off the lights - I could only tell in the dark due to how dim the flashing on the display was) where de "Powered by Android" logo kept flashing for a millisecond and in a loop. None of the button combinations worked so I couldn't switch completely off, access recovery/fastboot, and my computer wouldn't recognise the phone when I connected it via USB. I ended up buying an EDL cable for deep flashing Qualcomm phones (€9) and within minutes I was back up and running. All solved.
~SilverLad~ said:
I had a similar issue: Bricked and totally unresponsive phone (or so I thought until I realized the screen was flashing very faintly when I switched off the lights - I could only tell in the dark due to how dim the flashing on the display was) where de "Powered by Android" logo kept flashing for a millisecond and in a loop. None of the button combinations worked so I could switch completely off, access recovery/fastboot, and my computer wouldn't recognize the phone when I connected it via USB. I ended up buying an EDL cable for deep flashing Qualcomm phones (€9) and within minutes I was back up and running. All solved.
Click to expand...
Click to collapse
Can you post a link to where you purchased the cable?
abprie said:
Can you post a link to where you purchased the cable?
Click to expand...
Click to collapse
I bought it from Amazon. The one I bought is out of stock now, but there are a lot of them available (from other brands/sellers). This one for example - is the one that most resembles the one I actually bought: https://www.amazon.es/ASHATA-tel%C3%A9fono-reparaci%C3%B3n-Adaptador-Engineering/dp/B086WZMFKW/ref=sr_1_18?__mk_es_ES=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=cable+edl&qid=1597417614&sr=8-18
Since the thread is already on topic, could I flash lineage os while being on a custom rom? I have Bliss ROM on partition A and stock on B. Is it possible to have both Bliss and Lineage in dual boot?
Also, maybe a little off topic, the partition A/B scheme was intended to be used as a dual OS boot like normal PCs? Because right now I can select A and boot Bliss, select B and boot stock, I don't get why the procedure for flashing Lineage OS is so convoluted(requires having stock both on B and A?!) since both partition seems to be standalone and separated from each other.
~SilverLad~ said:
I bought it from Amazon. The one I bought is out of stock now, but there are a lot of them available (from other brands/sellers). This one for example - is the one that most resembles the one I actually bought: https://www.amazon.es/ASHATA-tel%C3%A9fono-reparaci%C3%B3n-Adaptador-Engineering/dp/B086WZMFKW/ref=sr_1_18?__mk_es_ES=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=cable+edl&qid=1597417614&sr=8-18
Click to expand...
Click to collapse
Hey there, what's the process around using this cable?
vikashhero said:
Hey there, what's the process around using this cable?
Click to expand...
Click to collapse
The cable itself (on its own), doesn't seem to "do" anything, but is paramount in reaching the right area, in order to fix the problem by means of the appropriate instructions and files. I can't recall where I ended up getting the right instructions from - as I researched quite a bit, and did a lot of "trial an error" before getting it right - so I'm sorry but I can't refer you directly to them via link (so that whoever posted them originally gets the credit they deserve), but this is what I ended up doing (on a WINDOWS machine) based on said instructions:
DOWNLOADS:
- Qualcomm drivers: https://androidfilehost.com/?fid=11410963190603857508
- Firmware with scripts: https://androidfilehost.com/?fid=1395089523397969054
- Latest official ASUS firmware from the ASUS webpage (download and place it in a memory card)
- (If you don't already have it on your WINDOWS machine): download and install Microsoft Visual C++ 2010 Service Pack 1 Redistributable Package
PROCEDURE:
1- Install the Qualcomm drivers
2- Unpack the downloaded firmware containing the scripts
3- Place the memory card in the phone's slot (with the latest official ASUS firmware already in it)
4- Power off the phone by VolumeDown + Power buttons (keep them pressed for about <25 seconds)
5- Connect the phone to the computer via the EDL cable and press the button on the EDL cable (there was an extra bit on what to do with a archive from the drivers file if your computer doesn't recognise the port straight away, but it wasn't necessary in my case so I didn't keep that step/archive name in my notes... I'm afraid you will have to search for it like I did if you come across that issue).
6- Start update_image_EDL.bat script from the unpacked firmware
7- After the script in step 6 finishes, start script flashall_AFT.cmd
8- Start bootloader
9- Go to stock recovery mode and install the ASUS firmware from the memory card
X- (Instructions also suggested to repeat steps 8 & 9 again at this point - for a second time - but in my case it wasn't needed)
I hope this helps.
~SilverLad~ said:
The cable itself (on its own), doesn't seem to "do" anything, but is paramount in reaching the right area, in order to fix the problem by means of the appropriate instructions and files. I can't recall where I ended up getting the right instructions from - as I researched quite a bit, and did a lot of "trial an error" before getting it right - so I'm sorry but I can't refer you directly to them via link (so that whoever posted them originally gets the credit they deserve), but this is what I ended up doing (on a WINDOWS machine) based on said instructions:
DOWNLOADS:
- Qualcomm drivers: https://androidfilehost.com/?fid=11410963190603857508
- Firmware with scripts: https://androidfilehost.com/?fid=1395089523397969054
- Latest official ASUS firmware from the ASUS webpage (download and place it in a memory card)
- (If you don't already have it on your WINDOWS machine): download and install Microsoft Visual C++ 2010 Service Pack 1 Redistributable Package
PROCEDURE:
1- Install the Qualcomm drivers
2- Unpack the downloaded firmware containing the scripts
3- Place the memory card in the phone's slot (with the latest official ASUS firmware already in it)
4- Power off the phone by VolumeDown + Power buttons (keep them pressed for about <25 seconds)
5- Connect the phone to the computer via the EDL cable and press the button on the EDL cable (there was an extra bit on what to do with a archive from the drivers file if your computer doesn't recognise the port straight away, but it wasn't necessary in my case so I didn't keep that step/archive name in my notes... I'm afraid you will have to search for it like I did if you come across that issue).
6- Start update_image_EDL.bat script from the unpacked firmware
7- After the script in step 6 finishes, start script flashall_AFT.cmd
8- Start bootloader
9- Go to stock recovery mode and install the ASUS firmware from the memory card
X- (Instructions also suggested to repeat steps 8 & 9 again at this point - for a second time - but in my case it wasn't needed)
I hope this helps.
Click to expand...
Click to collapse
Hey buddy, I appreciate your reply. The cable is on its way but I got a bit fiesty and opened up the phone to short the two contacts. This did the trick for me, got me back into EDL mode, and I was able to flash the latest firmware. On that topic, I'm trying to find the most suitable firmware version to run LineageOS 17 on the phone. I grabbed Mauro's TWRP to temporarily boot into which allowed me to flash the latest Asus image from their site. I guell I'll just carry on from there.
vikashhero said:
Hey buddy, I appreciate your reply. The cable is on its way but I got a bit fiesty and opened up the phone to short the two contacts. This did the trick for me, got me back into EDL mode, and I was able to flash the latest firmware. On that topic, I'm trying to find the most suitable firmware version to run LineageOS 17 on the phone. I grabbed Mauro's TWRP to temporarily boot into which allowed me to flash the latest Asus image from their site. I guell I'll just carry on from there.
Click to expand...
Click to collapse
As far as I understand, that's pretty much what the cable does actually... I also came across that method along my research, but I didn't want to risk opening the phone up. Since you are in the "flashing state": be careful with some of the instructions out there - I flashed through TWRP as I have been doing all these years with other phones, following specific instructions for each ROM I've tried, and I had nothing but issues until I flashed through ADB. I still don't know why I was getting the "No OS" warning all the time despite flashing correctly from TWRP (contemplating the A/B partitions matter), but none worked...
~SilverLad~ said:
As far as I understand, that's pretty much what the cable does actually... I also came across that method along my research, but I didn't want to risk opening the phone up. Since you are in the "flashing state": be careful with some of the instructions out there - I flashed through TWRP as I have been doing all these years with other phones, following specific instructions for each ROM I've tried, and I had nothing but issues until I flashed through ADB. I still don't know why I was getting the "No OS" warning all the time despite flashing correctly from TWRP (contemplating the A/B partitions matter), but none worked...
Click to expand...
Click to collapse
Appreciated but I'm all sorted. I believe my pitfall was not using the copy-partitions .zip file detailed in the instructions. I had no idea that was a thing. Was extra careful this time and now I'm on the ROM I need.
I ****ing hate A/B partitioned phones, makes custom ROMs such a chore. Sort of getting fed up with phones in general but at least this is working well for now.
vikashhero said:
Appreciated but I'm all sorted. I believe my pitfall was not using the copy-partitions .zip file detailed in the instructions. I had no idea that was a thing. Was extra careful this time and now I'm on the ROM I need.
Click to expand...
Click to collapse
Happy to hear that Indeed be careful - this is a tricky phone...
vikashhero said:
I ****ing hate A/B partitioned phones, makes custom ROMs such a chore. Sort of getting fed up with phones in general but at least this is working well for now.
Click to expand...
Click to collapse
Same here. It was so easy to do the Samsungs "back in the day", and you always had ODIN as a fallback if things went south. But this "A/B" partition nonsense (as well as other useless changes they introduce every time they "upgrade" Android, or certain structure modifications every so often when a new phone comes out) are a pain in the butt! Changes clearly aimed at making things more annoying/difficult for us people who don't want standard/corporate/unnecessarily bloated phones... Actually (as a former Blackberry user) I was tempted to get one of these Android based Blackberrys (the KEY2), but I didn't in the end precisely due to the fact that the bootloader can't be touched, and it can be rooted...
vikashhero said:
Appreciated but I'm all sorted. I believe my pitfall was not using the copy-partitions .zip file detailed in the instructions. I had no idea that was a thing. Was extra careful this time and now I'm on the ROM I need.
I ****ing hate A/B partitioned phones, makes custom ROMs such a chore. Sort of getting fed up with phones in general but at least this is working well for now.
Click to expand...
Click to collapse
I want to switch to because the latest security update (August 2020) by Asus is soft bricking the phone for many users,
but I am seeing a few reports about some bugs (like the phone is stuck in the lineage boot symbol and cellular errors) in lineage os and also seeing few post with a lot of installation errors (like soft and total bricking) etc. and for me in developers options I'm not seeing the OEM and advanced boot options.(in my asus stock os) I just found out that I have to download the Unlock Boot loader apk separately from asus and install it using command prompt so I don't know how to proceed.
Can you please elaborate on how you actually did it with your Asus Zenfone 6(2019), I am a total noob in this and I also couldn't understand the partition a and b parts too.