Develop Bugs

[SHV-E250s] Bricked my phone

Hi guys,
Got my Korean LTE (SHV-E250s) yesterday and thought I'd root it so I can install a new English OS on it (Cleanrom Ace 4.5).
I followed Chainfire's thread on how to root my phone (http://forum.xda-developers.com/showthread.php?t=1933542).
So, first I downloaded Odin3 v1.85 and CF-Auto-Root-t0lteskt-t0lteskt-shve250s.zip.
Extracted both and managed to install CF Auto Root with SuperSU v1.05.
Sweet, everything was going well.
Then I found Cleanrom Ace 4.5 and its thread (http://forum.xda-developers.com/showthread.php?t=2055170).
So I installed Goomio from the play store and downloaded the current version of "twrp".
Now, here is where I stuffed up bad because I didn't make a backup.
I copied the zip file of Cleanrom Ace 4.5 onto my micro SD as well as the internal storage.
I booted the phone into twrp and went to factory wipe and reset. I got a little bit worried here because this is where things go wrong.
I went ahead and did it, rebooted to twrp again and installed Cleanrom Ace 4.5.
I got to the options and it was looking hopeful. Chose stock or custom animations to boot up, apps to install, etc.
Then it went to installation screen showing the progress and it stayed on 0.0% when it was trying to install the boot up animations.
After about 2 minutes or so it would reboot. I would try and install the ROM again but each time I got the same thing.
I tried rebooting normally but then twrp told me that I didn't have an OS to boot to. Uh oh.
After doing another wipe and reset, I could access the download mode (vol down+home+power) and the other mode, which I'm not sure if it's recovery mode? (vol up+home+power).
I tried using Odin3 v1.08, v.3.04 and 3.07 to load up some stock ROMs (N7105ZHDMB1_N7105ZZHDMB1_N7105XXDLL5_HOME.tar.md5, N7105XXDMB2_N7105TMHDLK8_N7105XXDLL5_HOME.tar.md5, and N7105XXDMB2_N7105VNZDMA2_N7105XXDMA1_HOME.tar.md5).
I tried using different USB ports and different computers. Each time I would get a red 'FAIL' screen in Odin3.
Below is an example of the message I'd get from Odin3 v3.07:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7105ZHDMB1_N7105ZZHDMB1_N7105XXDLL5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> tz.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone help me? My phone gets stuck on the "Samsung Galaxy Note II" window and doesn't progress. I hold down the power button and it just reboots to the same window. I can get to download mode and what I think is recovery mode.
Any guidance is very appreciated. I have read around the threads and I know this isn't a hard brick so there may be some way to resolve this.
Cheers

Maybe this will help you or wait for Dr.Ketan to help you is a real doctor.
http://forum.xda-developers.com/showthread.php?t=2143515

adinfsfocus said:
Maybe this will help you or wait for Dr.Ketan to help you is a real doctor.
http://forum.xda-developers.com/showthread.php?t=2143515
Click to expand...
Click to collapse
Hi there, thanks for the link. I'm glad your issue was resolved.
However, I don't think I created a backup, so I couldn't just do a backup through recovery.
I can't reinstall any of the stock firmware I've downloaded as it says 'failed' every time in Odin3.

Update: I can't get into recovery mode now.

1. Even I had the same situation wen I ran megawipe script but stock rom installation in download mode gave life to my phone...
So first try installin wit different versions of odins and roms..
2. May be the whole internal memory lost all the partitions into which the files could be flashed.. 'wipe data factory reset' in recovery would have put them back ..but since ur phone recovery too is lost search for a tool which can put them back as I remember readin about such a tool... will search too..
Sent from my GT-N7100 using Tapatalk 2

maloolaba said:
Hi there, thanks for the link. I'm glad your issue was resolved.
However, I don't think I created a backup, so I couldn't just do a backup through recovery.
I can't reinstall any of the stock firmware I've downloaded as it says 'failed' every time in Odin3.
Click to expand...
Click to collapse
Try instal a costom recovery after you instal costom recovery with Odin (make a full wipe,format system,partition,wipe cache and dalvik) then download a costom rom and put on external SD card if you have if not borrow one or buy one and instal the rom from external Sd card.
I hope you solved.

adinfsfocus said:
Try instal a costom recovery after you instal costom recovery with Odin (make a full wipe,format system,partition,wipe cache and dalvik) then download a costom rom and put on external SD card if you have if not borrow one or buy one and instal the rom from external Sd card.
I hope you solved.
Click to expand...
Click to collapse
Would I still need GooManager or Terminal Emulator to install a custom rom like twrp? Because I can't install apps like GooManager or Terminal Emulator as my phone is bricked.
edit: Tried installing TWRP recovery using this hxxp://androidlegend.com/install-twrp-recovery-2-3-1-1-on-galaxy-note-2-n7100/ but Odin3 kept crashing every time I hit "start". I don't know if it's because my phone is an SHV-E250S and not a n7100 or what?
double edit: Update. I can get recovery mode again! Weird.
Options are:
reboot system now
apply update from ADB
apply update from external storage
wipe data/factory reset
wipe cache partition
apply update from cache
So I went ahead and selected "wipe data/factory reset". Rebooted and still the same.

Oh man!
So I've tried the method in this thread (http://forum.xda-developers.com/showthread.php?t=2040264) for Verizon Note 2 and I had a minor progress.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605_VRALJB_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
The progress bar underneath where it would say PASS or FAIL actually said something, ie. Boot, which is something that hasn't happened with the stock ROMs I've tried in the first post. Now I just need a stock from for the SHV-E250s that will work!
Upon rebooting, it adds to my flash number, so it is writing, but not completing the install.

Has anyone got any ideas I can try?

maloolaba said:
Has anyone got any ideas I can try?
Click to expand...
Click to collapse
Try contact dr.ketan is a master:good:
http://forum.xda-developers.com/showthread.php?t=1896696

After wipe data/factory reset in recovery did u try changing into download mode n flashin rom through pc odin ???.. plz try it if u have not..
Sent from my GT-N7100 using Tapatalk 2

hkkanha said:
After wipe data/factory reset in recovery did u try changing into download mode n flashin rom through pc odin ???.. plz try it if u have not..
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
Yes, I did just that. Still no luck. Is this possibly because there isn't much support for the SHV-E250s in terms of recovery ROMs and Odin3?
A recovery ROM for N71000 was able to begin writing on my phone, thus increasing flash count, but failed at the beginning in Odin3.
I don't know if it's a ROM problem or a phone problem or an Odin3 problem?
Noob here, btw.

these stock ROMs that you have tried are not for galaxy note 2 korean version/shv-e250s..
try this latest stock ROM/firmware for shv-e250s : E250SKSVME1_E250SSKTVMAA_SKT.zip
get it from sammobile

m41n54j4 said:
these stock ROMs that you have tried are not for galaxy note 2 korean version/shv-e250s..
try this latest stock ROM/firmware for shv-e250s : E250SKSVME1_E250SSKTVMAA_SKT.zip
get it from sammobile
Click to expand...
Click to collapse
Please help, i really need pit file for SHV-E250s. I softbrick my phone. Please

tuannghia1985 said:
Please help, i really need pit file for SHV-E250s. I softbrick my phone. Please
Click to expand...
Click to collapse
Plz donot Install N7100 or N7105 Stock Rom on your SHV-E250S, Download Samsung Official Stock Rom from the link given Below and flash it through PC ODIN http://www.sammobile.com/firmwares/1/?model=SHV-E250S&pcode=SKT#firmware

Accidentally wiped everything in TWRP, "no OS installed" - what are my options?

Accidentally wiped everything in TWRP, "no OS installed" - what are my options?
I rooted my tablet last night and everything went fine, and the next step way to install a custom ROM. So I was attempting to move my download of CleanROM onto my external SD...but I forgot that I have no external SD card! I went into TWRP and wiped internal storage thinking it would be there, and now I get a message saying "No OS Installed are you sure you want to reboot?" whenever i try to exit TWRP.
I am assuming my only option at this point would be to ODIN back to stock? If anyone could tell me exactly how to do this, step by step (and specifically which files I need & where to get them) it would be greatly appreciated because my tablet is a $600 paperweight at this point and I am not too familiar with ODIN.
I also read some things about using something called "ADB" to load a ROM onto the tablet, but again I am not familiar with this at all and I would need to know specifically how to do this. I tried to figure it out with Google but all the instructions seemed too device-specific.

RTbar said:
I rooted my tablet last night and everything went fine, and the next step way to install a custom ROM. So I was attempting to move my download of CleanROM onto my external SD...but I forgot that I have no external SD card! I went into TWRP and wiped internal storage thinking it would be there, and now I get a message saying "No OS Installed are you sure you want to reboot?" whenever i try to exit TWRP.
I am assuming my only option at this point would be to ODIN back to stock? If anyone could tell me exactly how to do this, step by step (and specifically which files I need & where to get them) it would be greatly appreciated because my tablet is a $600 paperweight at this point and I am not too familiar with ODIN.
I also read some things about using something called "ADB" to load a ROM onto the tablet, but again I am not familiar with this at all and I would need to know specifically how to do this. I tried to figure it out with Google but all the instructions seemed too device-specific.
Click to expand...
Click to collapse
Steps to follow :
1. Extract the attached odin 3.09.
2. Download your region rom from here http://samsung-updates.com/device/?id=SM-P600 or if you are looking for US firmware then from here http://www.sammobile.com/firmwares/1/?model=SM-P600&pcode=XAR#firmware.
3. Unzip your firmware.
4. Go into download mode by pressing power + volume down, then volume up.
5. Connect your phone to your PC/Laptop until the com port on the left hand side turns blue.
6. Place your extracted rom in the "AP" bar.
7. Hit "Start"
8. Wait till installation is complete .
You should be good to go .

Thank you so much. Before i go ahead and do this, could you clarify one thing for me? On the firmwares page, it does not specify which one would be for the WiFi, American version which is what I have. Do you know which one i should choose? It does not specify "2014" edition anywhere so i just want to make sure i pick the right one, thanks

RTbar said:
Thank you so much. Before i go ahead and do this, could you clarify one thing for me? On the firmwares page, it does not specify which one would be for the WiFi, American version which is what I have. Do you know which one i should choose? It does not specify "2014" edition anywhere so i just want to make sure i pick the right one, thanks
Click to expand...
Click to collapse
These are all for the 2014 edition, just choose the latest build date Nov. MK1 for the US

RTbar said:
Thank you so much. Before i go ahead and do this, could you clarify one thing for me? On the firmwares page, it does not specify which one would be for the WiFi, American version which is what I have. Do you know which one i should choose? It does not specify "2014" edition anywhere so i just want to make sure i pick the right one, thanks
Click to expand...
Click to collapse
The firmware for USA is Cellular South http://terafile.co/574648641665/P600UEUBMK1_P600XARBMK1_XAR.zip

I think a small couple of small files in "data/media", which holds mostly unimportant stuff, must not get deleted or it's bricktime. Like when i once formatted "data" on my old tablet.

I had this same problem, however I fixed it using adb sideload. You can install it from here. First go to advanced in TWRP and click the ADB option. Then you just need to open cmd, change your directory to where the ROM zip is, then write "adb sideload test.zip" where the quotes are removed and test is the name of your zip which should be something like "CleanROM-2.0-R2.zip"

Thanks for all the help. I was able to get back to stock using Odin and am now rooted running CleanROM. I'll be using that ADB info in the future for sure too.

Dealing with the same issue!
I did this too but this was my result. Note 4 Sprint.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910PVPU1BOB7_N910PSPT1BOB7_N910PVPU1BOB7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Whats going on?

Fractality said:
I did this too but this was my result. Note 4 Sprint.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910PVPU1BOB7_N910PSPT1BOB7_N910PVPU1BOB7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Whats going on?
Click to expand...
Click to collapse
It was be not Your model's firmware.
Try appropriate or exclude all except: bootloader, recovery, system & cache

stslam said:
It was be not Your model's firmware.
Try appropriate or exclude all except: bootloader, recovery, system & cache
Click to expand...
Click to collapse
Same thing is happening with me. How I can edit it ?
I tried Winzip and 7Zip but there are errors in Odin...

I'm facing a similar issue but my device is Moto G5s Plus.
The problem I'm facing is that I accidently wiped out the mobile's system completely, and now it does not even have an "internal storage" partition at all (since it shows 0 MB). Hence, I cannot even transfer any files to my mobile because my computer does show the phone detected but no "internal storage exists".
Please help me out..

asim.sidz said:
I'm facing a similar issue but my device is Moto G5s Plus.
The problem I'm facing is that I accidently wiped out the mobile's system completely, and now it does not even have an "internal storage" partition at all (since it shows 0 MB). Hence, I cannot even transfer any files to my mobile because my computer does show the phone detected but no "internal storage exists".
Please help me out..
Click to expand...
Click to collapse
If you have TWRP installed you may be able to flash a custom rom through OTG...
Otherwise you may be in the toilet...

hello ,I have galaxy note 2 Korea version ,model SHV-E250S build no KOT49H.E250SKSUKOH4 ,i try to update lineage os ,but unfortunately formatted OS ,now ohone showing no OS installed ,can someone help ,where to get sock rom for this model. i tried too many roms via TWRP & odin ,but error occured & solution is not there,plz help

Samsung a600fn
I did the same thing now it says no is installed and I don't know what firmware to install because I don't know the name of the file please help

Need guidance
Please tell me somebody still reads this.
So I recently got this tablet. Deleted everything.
Now it says no os installed.
I tried the odin suggestion. But odin keeps crashing on me.
Tried to install a hyperdrive zip though twrp. Just reboots.
It also says no super su installed.
Help. I haven't done this years and have no clue

BoomDiggy said:
Please tell me somebody still reads this.
So I recently got this tablet. Deleted everything.
Now it says no os installed.
I tried the odin suggestion. But odin keeps crashing on me.
Tried to install a hyperdrive zip though twrp. Just reboots.
It also says no super su installed.
Help. I haven't done this years and have no clue
Click to expand...
Click to collapse
I would try a different version of Odin Also make sure you have the correct tablet ROM, try getting yourself back to stock before other ROMS.

louvass said:
I would try a different version of Odin Also make sure you have the correct tablet ROM, try getting yourself back to stock before other ROMS.
Click to expand...
Click to collapse
Yes, and run Odin as admin (I'm an active user)

louvass said:
I would try a different version of Odin Also make sure you have the correct tablet ROM, try getting yourself back to stock before other ROMS.
Click to expand...
Click to collapse
Ty for replying.
I think I have the correct firmware file from sammobile. EUR-P600XXSDRI1-20190117145157.zip
I also noticed that the tablet says that there is no root. But I have trwp.

i accidentali wiped everything in TWRP ON MY REALME 3 PRO... now stuck in bootloader with twrp working.....

[Q] Softbrick, bootloop, TWRP Password

My girlfriends S3 (Bell, I747M, d2can) is currently boot looping. It had a custom ROM on it, but I'll be damned if I could tell you which one. It was working, then it wasn't. No updates, no flash/wipe/etc.
Now I turn on her phone, and it gets to the ROM's boot screen, and just as it's about to complete, it restarts again. I can enter TWRP (2.6.3.1) but it requires a password (which is a bug, afaik). I can press "cancel" and try to reset/wipe, but it won't mount or reset the cache partition, so it fails.
I used Odin (3.07, 3.09) to try and flash TWRP 2.6.3.0 and 2.7.0.0, and both failed. The result was Odin would reboot the phone, then it would enter the same bootloop, and the recovery would still be TWRP 2.6.3.1.
I tried downloading a stock S3 firmware and flashing it with Odin. Same problem.
I've tried new drivers. New cable. New USB port. I've tried using a different computer. Always the same result.
So a summary of what I can/can't do:
Can't use TWRP to reset/wipe
Can't use ADB Sideload
Can't modify device via ADB
CAN see the device via ADB
CAN enter download mode
Any help?
I pulled DMESG at some point during all this. Maybe it can help shed some light: http://pastebin.com/4c2uL3Qq

Dont know how much help it is but I quit using TWRP because of that bug, now I use CWM the philz touch version and haven't seen that again. When you are flashing the rcovery with ODIN you must absolutely uncheck the box for auto reboot. when you get the message that says the flash was successful you should then unplug the USB cable and do a battery pull, reinsert the battery, press the volume up key and the home key, press the power button until it vibrates then release the power button only, once the phone boots into recovery you may release the volume up and home buttons.
If you are trying to flash Stock roms be darn sure you have the right stuff IE AT&T phone using 4.3 you find here on XDA the correct odin flashable tar or for any other use www.sammobile.com if you have a canadian I747M go to www.sammobile.com and find the right one for the bootloaders currently on the phone. If you flash a phone that has 4.3 bootloaders on it with older bootloaders you will have an instant Hard Brick. Use Extreme Caution with bootloaders and ODIN tars. you could also use custom recovery to flash some stock or custom roms too those are alot safer and less likely to hard brick.
I think you are on the right track to trying to fix your ahem her phone, a little patience and reading go a long way IIRC the recovery thread instructions outline the need to uncheck the auto reboot box, with that being said you aren't the first one to over look it I have done it myself a few months ago. I wish you the best of luck and hope that a cache wipe will fix what you have going on if not try a factory reset, Good Luck.

theramsey3 said:
Dont know how much help it is but I quit using TWRP because of that bug, now I use CWM the philz touch version and haven't seen that again. When you are flashing the rcovery with ODIN you must absolutely uncheck the box for auto reboot. when you get the message that says the flash was successful you should then unplug the USB cable and do a battery pull, reinsert the battery, press the volume up key and the home key, press the power button until it vibrates then release the power button only, once the phone boots into recovery you may release the volume up and home buttons.
If you are trying to flash Stock roms be darn sure you have the right stuff IE AT&T phone using 4.3 you find here on XDA the correct odin flashable tar or for any other use www.sammobile.com if you have a canadian I747M go to www.sammobile.com and find the right one for the bootloaders currently on the phone. If you flash a phone that has 4.3 bootloaders on it with older bootloaders you will have an instant Hard Brick. Use Extreme Caution with bootloaders and ODIN tars. you could also use custom recovery to flash some stock or custom roms too those are alot safer and less likely to hard brick.
I think you are on the right track to trying to fix your ahem her phone, a little patience and reading go a long way IIRC the recovery thread instructions outline the need to uncheck the auto reboot box, with that being said you aren't the first one to over look it I have done it myself a few months ago. I wish you the best of luck and hope that a cache wipe will fix what you have going on if not try a factory reset, Good Luck.
Click to expand...
Click to collapse
Appreciate all the help! I've tried pretty much every combination.
I've turned off auto-reboot, flashed, but Odin stops at:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
Click to expand...
Click to collapse
I assume that's where it's supposed to be. Then I enter recovery and it's still the same TWRP 2.6.3.1. Very strange.
I don't think her phone is using 4.3 bootloaders, as I don't remember them being available when I flashed this phone. I'm a Nexus guy, so maybe I'm doing something wrong this time.
EDIT: I also seem to recall on my phones that when I flashed something in Download/Fastboot mode, there was a progress bar of sorts on the phone itself indicating it was receiving something. On this phone it doesn't display anything to imply something's happening.

Boot into download and let us know what it says on the download screen. If you have the 4.3 bootloader, try flashing a pre-rooted 4.3 Bell ROM using Odin 3.07. If you have a lower version bootloader, try flashing a pre-rooted 4.1.1 or 4.1.2 ROM.
http://forum.xda-developers.com/sho...mctr=(not provided)&__utmv=-&__utmk=139036464
In Odin, don't check auto reboot. When you see reset in the status windows, disconnect the USB cable and pull the battery. Boot into recovery and wipe cache, data, and reboot.

Thanks for the reply! I'm 99% sure it's a pre-4.3 bootloader. Here's what it shows in DL mode:
ODIN MODE
PRODUCT NAME: SHG-I747M
CUSTOM BINARY DOWNLOAD: Yes (2 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
DUALCOMM SECUREBOOT: ENABLE
If I recall correctly, a 4.3 bootloader would show two more lines at the bottom.

Tried installing a 4.1.1 ROM (root66_BMC_I747MVLDLK4)
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_BMC_I747MVLDLK4.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
4.1.2 (root66_BMC_I747MVLDMF1.7z)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_BMC_I747MVLDMF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse

I feel it's worth mentioning again: At no point, while using Odin, does the phone display a transfer bar of any sort.

Try installing Philz Touch recovery via Odin and see if you can boot into recovery. Copy a custom ROM on an external SD card and see if you can flash that ROM from recovery.

audit13 said:
Try installing Philz Touch recovery via Odin and see if you can boot into recovery. Copy a custom ROM on an external SD card and see if you can flash that ROM from recovery.
Click to expand...
Click to collapse
Tried Philz and Odin still doesn't seem to have flashed it.
I'll try with an SD card.

X04D said:
Tried Philz and Odin still doesn't seem to have flashed it.
I'll try with an SD card.
Click to expand...
Click to collapse
Try this: when you flash with Odin, uncheck auto reboot, start the flash process. When you see the word reset in the status window, remove the USB cable, pull the battery, and boot into recovery.

[Q] Unable to flash to stock with odin / having two 0 directories

So newb questions and might have been answered but I have been unable to find the answer I'm looking for.
Background:
SGH T999
Original I was on 4.1 stock. I used towelroot and was able to root and all that jazz. I uploaded an old version of CWM to my phone and was unable to flash and ROMs, they would all hang on the Samsung Galaxy SIII screen.
I updated CWM to put on a Cyanogen Mode ROM and all was good. I tried out a couple other ROMs then decided I wanted to go back to stock and see how stock 3.3 or 3.4 was. I tried using Odin to bring back to stock and no luck. I then installed PhilZ recovery and booted to Wicked ROM for 4.1. After this I got current TWRP and tried to update other roms. I went into ROM manager switched over to CWM 6.0.4.5 then updated my kernel. At some point along the way I noticed that on the internal sd card I have a 0 directory inside my 0 directory.
Now when I reboot my phone into Recovery mode I see a Samsung Galaxy SIII screen with the Cyanogen guy on it, then it loads to CWM but nothing is on the screen but the hat, then after a couple of seconds it loads to a Samsung screen quickly, then to the Samsung Galaxy SIII and hangs indefinitely. I'm still able to get the phone to go into download mode fine. Now I'm trying to just bring back to stock but not having any luck. Here's my repro:
1. Put hardware into download mode (HOME + Vol Down + Lock).
2. Open Odin 3.09 as Admin (I'm using Win 7).
3. Connect hardware to computer (Odin recognizes 0:Com5).
4. Place "T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5" in AP field.
5. With only "Auto Reboot" and "F.Reset Time" selected press Start button.
RESULT:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Then on my hardware I get
ODIN MODE
PRODUCT NAME: SGH-T999
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Offical
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOADER AP SWREV: 1
SW REV CHECK FAIL : Fused 1 > Binary 0
Click to expand...
Click to collapse
Any idea's how I can bring this back?

tiger_johnson said:
*snip*
Any idea's how I can bring this back?
Click to expand...
Click to collapse
Hmm, if the device is recognized in your PC by ODIN there's still hope. I personally recommend TWRP (LINK for latest ODIN flashable version) for everything as CWM has caused havoc with my phone before. Stay away from it. IF you can still access recovery, do format everything, including the internal SDcard. Also please use the PIT file when trying to use ODIN for the MD5 firmware you're choosing. LINK for the PIT file (choose your model's PIT and put it on the PIT part of ODIN then proceed on flashing the MD5 firmware - credit goes to DocHoliday for the PIT files). That little file can sometimes fix stuff when trying to ODIN the device back to stock firmware. Just giving ideas, don't give up and best of lucks!

You can't flash MD5. It looks like you are currently running MJC base firmware which means you can ONLY flash MJC or NC2 with Odin. Do not try to downgrade via any method or it will hard brick your device.
Sent from my SAMSUNG-SGH-I747 using Tapatalk
---------- Post added at 12:25 AM ---------- Previous post was at 12:23 AM ----------
"SW REV CHECK: Fused 1" means you currently have MJC. It will change to Fused 2 if you update to NC2. (If I'm remembering all those nemesis right).
Just FYI in case anyone was wondering.
Sent from my SAMSUNG-SGH-I747 using Tapatalk

Samsng Tab 3 7.0 probably hard bricked

My Samsung SM-T210R is in trouble . It all started after flashing a rom, I believe it was TranchidaKat v 4.3, However after that I have tried so many things that the start means little now.
Situation:
The tablet does not boot either to regular boot or into recovery. It actually appears pretty dead when trying, unless one pays attention to the back lighting of the screen.
Eventually I managed to consistently boot into download (actually ODIN) mode although without the large texting with the warnings and the instruction to press the up volume button (which I do nonetheless).
The report on screen upper left says:
ODIN MODE
PRODUCT NAME: SMT210R
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
HW REV: 0x5
From there attempting to flash a number of roms including stock fails. The MD5 checks are always successful. The failure modes are 2 different ones.
The first involves a PIT Partition missing. It happens when attempting to flash non stock roms
The second, flashing a stock rom (the latest: T210RUEU0COB1 and also: T210RUEAMK1 ) or also TWRP Recovery shows:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection.. (It hangs at this point for a very long time)
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I did a lot of searching for a pit file for my tablet model without coming up with it.
Can someone help me to solve this please?

untamed1 said:
My Samsung SM-T210R is in trouble . It all started after flashing a rom, I believe it was TranchidaKat v 4.3, However after that I have tried so many things that the start means little now.
Situation:
The tablet does not boot either to regular boot or into recovery. It actually appears pretty dead when trying, unless one pays attention to the back lighting of the screen.
Eventually I managed to consistently boot into download (actually ODIN) mode although without the large texting with the warnings and the instruction to press the up volume button (which I do nonetheless).
The report on screen upper left says:
ODIN MODE
PRODUCT NAME: SMT210R
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
HW REV: 0x5
From there attempting to flash a number of roms including stock fails. The MD5 checks are always successful. The failure modes are 2 different ones.
The first involves a PIT Partition missing. It happens when attempting to flash non stock roms
The second, flashing a stock rom (the latest: T210RUEU0COB1 and also: T210RUEAMK1 ) or also TWRP Recovery shows:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection.. (It hangs at this point for a very long time)
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I did a lot of searching for a pit file for my tablet model without coming up with it.
Can someone help me to solve this please?
Click to expand...
Click to collapse
Are you tried the search Funktion?
http://forum.xda-developers.com/showthread.php?t=2625163
Here are what you want.

bierma32 said:
Are you tried the search Funktion?
http://forum.xda-developers.com/showthread.php?t=2625163
Here are what you want.
Click to expand...
Click to collapse
Thank you for your response.
First if with search function you mean by using google, I have done a lot of of that, but so far with no luck.
I am pretty good with this stuff but not good enough. I would like to find someone who has either a lot of knowledge or has resolved a situation like mine and is willing to help.
The link you suggested is probably good, but does not totally relate to my situation. They had a working device they were simply trying to root. I instead don't have a working device and not even access to recovery mode. I don't even know right now what files and folders are on my device.
Thank you for the pit file though; now I have to find out whether repartitioning with it would be good, or whether it would push me down deeper in the hole.

You can also use the search Funktion here at this forum.
All wath you must do is simular to flash a recovery with Odin.
Download the Stockton from sammobile.com
Boot your tab into download mode
Startup odin
Check autoreboot , repartion and factory reset.
Under Pit you select the Pit.file
Under PDA you select your downloaded Stockrom what you have unziped,so that have a *.tar.md5 extension.
Press Start and Walt some minutes and the Tab will reboot.

bierma32 said:
You can also use the search Funktion here at this forum.
All wath you must do is simular to flash a recovery with Odin.
Download the Stockton from sammobile.com
Boot your tab into download mode
Startup odin
Check autoreboot , repartion and factory reset.
Under Pit you select the Pit.file
Under PDA you select your downloaded Stockrom what you have unziped,so that have a *.tar.md5 extension.
Press Start and Walt some minutes and the Tab will reboot.
Click to expand...
Click to collapse
Bierma32,
first of all thank you for spending the time to assist me it is very much appreciated. I followed your procedure and unfortunately it went nowhere fast. This is the report from Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210RUEU0COB1_T210RXAR0COB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
This is what happened earlier with the only difference being the "Set PIT file" command.
Any idea?

It looks like that Pit.file isnt working. Take a look in this link for a other Pit.file
http://forum.xda-developers.com/showthread.php?t=2722948

Hi. Im not able to help you, but im having issues aswell. I tried flashing some different things trying to root my device.. it seems it worked, but it never rooted it or anything even though my system status is Custom and the build number ****ing changed. Could you please tell me where you found your stocks for your device? To unroot.. i'd really appreciate it. I can't find any.

Rom's for Samsung Tab 3 7.0 SM-T210R
Doom1337 said:
Hi. Im not able to help you, but im having issues aswell. I tried flashing some different things trying to root my device.. it seems it worked, but it never rooted it or anything even though my system status is Custom and the build number ****ing changed. Could you please tell me where you found your stocks for your device? To unroot.. i'd really appreciate it. I can't find any.
Click to expand...
Click to collapse
For non stock ROM's:
http://forum.xda-developers.com/galaxy-tab-3/development-7
For Stock ROM's:
http://www.sammobile.com/firmwares/
For stock there are faster download sources also, do some google searching. By the way my issue has nothing to do with rooting.

bierma32 said:
It looks like that Pit.file isnt working. Take a look in this link for a other Pit.file
http://forum.xda-developers.com/showthread.php?t=2722948
Click to expand...
Click to collapse
I had found another PIT file as well, that looked very promising but did not work. I will try these two. Thanks.
:fingers-crossed:

Continuation
bierma32 said:
It looks like that Pit.file isnt working. Take a look in this link for a other Pit.file
http://forum.xda-developers.com/showthread.php?t=2722948
Click to expand...
Click to collapse
Tried both PIT files at that link with no success. Thanks for you help anyway. I am starting to loose hope and to wonder whether the problem is really not with the PIT file and partition tables. I just wish I knew linux.

untamed1 said:
Tried both PIT files at that link with no success. Thanks for you help anyway. I am starting to loose hope and to wonder whether the problem is really not with the PIT file and partition tables. I just wish I knew linux.
Click to expand...
Click to collapse
When you connect charger do tab shows battery charging.
If it shows then probably your kernel is working.
(i don't know about Samsung too much as they have download mode instead of fastboot.)
Sent from my D2212 using XDA Free mobile app

No battery picture
vinay said:
When you connect charger do tab shows battery charging.
If it shows then probably your kernel is working.
(i don't know about Samsung too much as they have download mode instead of fastboot.)
Sent from my D2212 using XDA Free mobile app
Click to expand...
Click to collapse
No, I am at a lower level than the kernel, I am sure. The only thing ever showing is the wording at the download mode screen.
Another curious thing that seems to be happening is that the battery seems to discharging or not charging since I can only enter download mode only while or after connecting the charger.
Any way thanks for your response.

untamed1 said:
No, I am at a lower level than the kernel, I am sure. The only thing ever showing is the wording at the download mode screen.
Another curious thing that seems to be happening is that the battery seems to discharging or not charging since I can only enter download mode only while or after connecting the charger.
Any way thanks for your response.
Click to expand...
Click to collapse
you just hard bricked your device.
but download mode is working so still a hope.(untill power end)
which version of odin are you using.?

I am using 3.06. Battery is not really a problem, other than for the unknown reason why it discharges or does not charge completely. I am questioning whether all the trial and errors I have done, since the issue occurred, may have caused some collateral damage. In any case, I can still start download mode after a short time charging

untamed1 said:
I am using 3.06. Battery is not really a problem, other than for the unknown reason why it discharges or does not charge completely. I am questioning whether all the trial and errors I have done, since the issue occurred, may have caused some collateral damage. In any case, I can still start download mode after a short time charging
Click to expand...
Click to collapse
When this happen.
What was you doing.
Like
Your tab was running you turned off and it won't turn on. Or you flashed a rom/kernel and it won't turn on.
Sent from my D2212 using XDA Free mobile app

Vinay, as I said in my first post...
. . . . . . . It all started after flashing a rom, I believe it was TranchidaKat v 4.3, However after that I have tried so many things that the start means little now.
Situation:
The tablet does not boot either to regular boot or into recovery. It actually appears pretty dead when trying, unless one pays attention to the back lighting of the screen.
Eventually I managed to consistently boot into download (actually ODIN) mode although without the large texting with the warnings and the instruction to press the up volume button (which I do nonetheless). . . . . . . . .
I hope you have some specific ideas or suggestions on what I can try. Without that I have pretty much given up.

untamed1 said:
Vinay, as I said in my first post...
. . . . . . . It all started after flashing a rom, I believe it was TranchidaKat v 4.3, However after that I have tried so many things that the start means little now.
Situation:
The tablet does not boot either to regular boot or into recovery. It actually appears pretty dead when trying, unless one pays attention to the back lighting of the screen.
Eventually I managed to consistently boot into download (actually ODIN) mode although without the large texting with the warnings and the instruction to press the up volume button (which I do nonetheless). . . . . . . . .
I hope you have some specific ideas or suggestions on what I can try. Without that I have pretty much given up.
Click to expand...
Click to collapse
First of all update your odin to 3.09 or higher if there is. And try flashing again.
(btw is that rom was made for your variant)
Sent from my Xperia E3 using XDA Free mobile app

same issue
i also have an unresponsive sm-t210r that has the OP's issues of a broken looking download screen, no boot and no recovery
pit file problems in odin and timeouts and now not postitive if my device made it to the 4.4.2 locked bootloader. looking to get it back to stock.
will help with files, time etc.
-ty

SOLVED
got my tab(SM-T210R) back up and running,,
been at it a few hours a day all this week,
kies firmware upgrade and initializaton somewhat didnt work. it installed it but always booted a black screen and backlight no sound. no vibiration,
so i am back to help the OP' and all others with this specific issue of dirty flashing directly to 4.4.2 from a rooted custom recovery tab3 that now have a messed up black screen problem but can still sneek into download mode thats looking all messed up> with the fallowing message
ODIN MODE
PRODUCT NAME: SMT210R
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
HW REV: 0x5
and then get PIT file errors and setup connection hangs.
please be shure you dont still have your custom recovery. you just have to hold home and vol+ ten seconds longer then usual after releasing the power button when the backlight appears. i thot i didnt have mine. until after i did this. now im just not shur if i held the buttons long enough then.
(if you need to get your current binary to offical please use odin's firmware and initialization process.. it will go thru and your binary will be changed to official but you will still have the black screen boot even though kies installed everything. proceed to next)
to get your brick back to being a useful loaf
this is what you need.
factory usb cable
odin 3.07
LT02.pit file from a 4.4.2 firmware (not 100%on that) ask me for the one i extracted if all eles fails
and T210.TWRP.2.8.0.0.tar.md5
start with opening odin
set your pit file and load the twrp recovery_
you want repartition checked for this (loading pit file should automatically fill the check box)
also autoreboot and f.reset time , checkboxes are checked
get your bricked device into download mode and connect
confirm odin sees the device and flash
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210.TWRP.2.8.0.0.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
at this point within 15 seconds after the reboot i got a splash screen and it booted up into 4.4.2 checked the status, device status of custom.
restarts and power offs are safe at this point. just take 5 seconds longer than normal.
so now we have an operating tablet with recovery and a messed up but working download mode.
checked download mode screen STILL CORRUPTED with the same weird message
ODIN MODE
PRODUCT NAME: SMT210R
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
HW REV: 0x5
i checked for twrp to operate it did. just took longer to boot it
PLEASE DO NOT AT THIS POINT wipe everything. it only got me back to the black screen with no booting.
and not being able to odin the .md5 package stock firmwares
it put me back an hour to get back to where these instructions end.
if this happends to you run keis firmware and intialize, to get the stock package back in and return to the corrupted download mode to see binary samsung offical.. then continue my odin instructions.
FALLOW UP:
had some time to experiment. i got back to %100 official system/binary and normal download mode with the green android guy being back.
i had updated to the latest TWRP and rooted.
i then unrooted with the super su app
then with the new kies program called SMARTSWITCH i again did the firmware and initialize and it went through and booted. without a hitch.
try it then go ahead and check for stock recovery and android man in download mode
-your welcome
b.t.w it seems in all the mess im still HW-rev 0x5 and it never installed the knox warraty bit..., blessing in disguise?
if this works for people somebody wanna make a sticky and add it to a 4.4.2 unbricking guide?
be aware that this is what worked for me. if you feel a different recovery or pit file may work go ahead. this is my results and wont be held accountable for what happens to you.
> DISCLAIMER> TRY AT YOUR OWN RISK< I AM NOT RESPONSIBLE

kal swift said:
got my tab(SM-T210R) back up and running,,
been at it a few hours a day all this week,
kies firmware upgrade and initializaton somewhat didnt work. it installed it but always booted a black screen and backlight no sound. no vibiration,
so i am back to help the OP' and all others with this specific issue of dirty flashing directly to 4.4.2 from a rooted custom recovery tab3 that now have a messed up black screen problem but can still sneek into download mode thats looking all messed up> with the fallowing message
ODIN MODE
PRODUCT NAME: SMT210R
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
HW REV: 0x5
and then get PIT file errors and setup connection hangs.
please be shure you dont still have your custom recovery. you just have to hold home and vol+ ten seconds longer then usual after releasing the power button when the backlight appears. i thot i didnt have mine. until after i did this. now im just not shur if i held the buttons long enough then.
(if you need to get your current binary to offical please use odin's firmware and initialization process.. it will go thru and your binary will be changed to official but you will still have the black screen boot even though kies installed everything. proceed to next)
to get your brick back to being a useful loaf
this is what you need.
factory usb cable
odin 3.07
LT02.pit file from a 4.4.2 firmware (not 100%on that) ask me for the one i extracted if all eles fails
and T210.TWRP.2.8.0.0.tar.md5
start with opening odin
set your pit file and load the twrp recovery_
you want repartition checked for this (loading pit file should automatically fill the check box)
also autoreboot and f.reset time , checkboxes are checked
get your bricked device into download mode and connect
confirm odin sees the device and flash
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210.TWRP.2.8.0.0.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
at this point within 15 seconds after the reboot i got a splash screen and it booted up into 4.4.2 checked the status, device status of custom.
restarts and power offs are safe at this point. just take 5 seconds longer than normal.
so now we have an operating tablet with recovery and a messed up but working download mode.
checked download mode screen STILL CORRUPTED with the same weird message
ODIN MODE
PRODUCT NAME: SMT210R
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
HW REV: 0x5
i checked for twrp to operate it did. just took longer to boot it
PLEASE DO NOT AT THIS POINT wipe everything. it only got me back to the black screen with no booting.
and not being able to odin the .md5 package stock firmwares
it put me back an hour to get back to where these instructions end.
if this happends to you run keis firmware and intialize, to get the stock package back in and return to the corrupted download mode to see binary samsung offical.. then continue my odin instructions.
FALLOW UP:
had some time to experiment. i got back to %100 official system/binary and normal download mode with the green android guy being back.
i had updated to the latest TWRP and rooted.
i then unrooted with the super su app
then with the new kies program called SMARTSWITCH i again did the firmware and initialize and it went through and booted. without a hitch.
try it then go ahead and check for stock recovery and android man in download mode
-your welcome
b.t.w it seems in all the mess im still HW-rev 0x5 and it never installed the knox warraty bit..., blessing in disguise?
if this works for people somebody wanna make a sticky and add it to a 4.4.2 unbricking guide?
be aware that this is what worked for me. if you feel a different recovery or pit file may work go ahead. this is my results and wont be held accountable for what happens to you.
> DISCLAIMER> TRY AT YOUR OWN RISK< I AM NOT RESPONSIBLE
Click to expand...
Click to collapse
I still cant get it working, i keep getting stuck with it saying it doesnt have a pit file even when i try to load it